# MEDAL II HERBICIDE

- EPA Reg No: **100-965**
- Registrant: SYNGENTA CROP PROTECTION, LLC
- Signal word: Caution
- Active ingredients: S-Metolachlor (82.4%)
- Label accepted: 2011-07-14
- Source PDF: https://www3.epa.gov/pesticides/chem_search/ppls/000100-00965-20110714.pdf

---
2011 r i7S
UNITED STATES ENVIRONMENTAL PROTECTION AGENCY
WASHINGTON, D.C. 20460
OFFICE OF CHEMICAL SAFETY
AND POLLUTION PREVENTION
Mr. Jerry Wells
Senior Regulatory Product Manager
Syngenta Crop Protection, Inc.
P.O. Box 18300 JUL M 20J'I
Greensboro, N.C 27419-8300
Subject: Label Amendment - Adding New York County Restrictions, Adding Resistance
Management Symbol, and Updating Warranty Statement
Product Name: Medal II Herbicide
EPA Registration Number: 100-965
Submission Date: April 1, 2011
Decision Number: 447557
Dear Mr. Wells:
The label amendment referred to above, submitted in connection with registration under
the Federal Insecticide, Fungicide, and Rodenticide Act (FIFRA), as amended is acceptable.
Please note that marketing claims made on the pesticide label must be substantiated by
data maintained in your files. If data supporting marketing claims made on the product label is
not available, then those claims must be removed.
Should you wish to add/retain a reference to the company's website on your label, then
please be aware that the website becomes labeling under the FIFRA, and is subject to review by
the Agency. If the website is false or misleading, the product would be misbranded and unlawful
to sell or distribute under FIFRA section 12(a)(l)(E). 40 CFR 156.10(a)(5) list examples of
statements EPA may consider false or misleading. In addition, regardless of whether a website is
referenced on your product's label, claims made on the website may not substantially differ from
those claims approved through the registration process. Therefore, should the Agency find or if
it is brought to our attention that a website contains false or misleading statements or claims
substantially differing from the EPA approved registration, the website will be referred to the
EPA's Office of Enforcement and Compliance.
Products shipped after 18 months from the date on this notice or the next printing of the
label whichever occurs first, must bear the new revised label. If these conditions are not
complied with, the registration will be subject to cancellation in accordance with FIFRA. Your
release for shipment of this product constitutes acceptance of these conditions. This label
supersedes all previously accepted labels. You must submit one copy of the final printed label
before the product is released for shipment. One copy of the label stamped "Accepted with
Comments" is enclosed for your records. If you have any questions, please contact Michael
Walsh by phone at (703) 308-2972 or via email at "walsh.michael@epa.gov",
SEE NEXT PAGE

Page 2 of 2
Label Amendment
Product Name: Medal II Herbicide
EPA Registration Number: 100-965
Decision Number: 447557
Sincerely,
Kathryn V. Montague
Product Manager (23)
Herbicide Branch
Registration Division (7505P)

[Front Cover of Removable Booklet - 2.5 Gallon and Bulk]
I GROUP BEE1 HERBICIDE
Note: It is illegal to sell, use or distribute this product within, or into, Nassau County or
Suffolk County, New York.
Medal® II
Herbicide
For weed control in corn, cotton, peanuts, pod crops, potatoes, safflowers, grain or
forage sorghum, and soybeans
Active Ingredient:
S-metolachlor (CAS No. 87392-12-9) 82.4%
Other Ingredients: 17.6%
Total:
Medal II contains 7.64 Ibs. of active ingredient per gallon.
KEEP OUT OF REACH OF CHILDREN.
CAUTION
See additional precautionary statements and directions for use inside booklet.
100.0%
Product of Switzerland
Formulated in the USA
EPA Reg. No. 100-965
EPAEst. 11773-IA-01VWC
EPA Est. 070989-IA-001OMH
EPAEst. 100-LAO-001SSG
(Superscript is first three letters of batch code on container)
SCP 965A L1 [2.5 gallon, Product ID 25060]
SGP 965A L2 [Bulk, Product ID 25061]
2.5 gallons
Net Contents
gallons
Net Contents
JUL I 4
f Under the yertsral Insecticide,
Pasgiolee, -AH~ SodentichJe Act,
! as amended, for ib.e pesfesida

r -2-
FIRST AID
If in eyes
If on skin or
clothing
If swallowed
If inhaled
« Hold eye open and rinse slowly and gently with water for 15-20
minutes.
• Remove contact lenses, if present, after the first 5 minutes, then
continue rinsing eye.
• Call a poison control center or doctor for treatment advice.
• Take off contaminated clothing.
• Rinse skin immediately with plenty of water for 15-20 minutes.
• Call a poison control center or doctor for treatment advice.
• Call a poison control center or doctor immediately for treatment
advice.
• Do not give any liquid to the person.
• Do not induce vomiting unless told to do so by the poison control
center or doctor.
• Do not give anything by mouth to an unconscious person.
• Move person to fresh air.
• If person is not breathing, call 91 1 or an ambulance, then give
artificial respiration, preferably mouth-to-mouth, if possible.
• Call a poison control center or doctor for further treatment advice.
Have the product container or label with you when calling a Poison Control Center or
doctor, or going for treatment.
HOT LINE NUMBER
For 24 Hour Medical Emergency Assistance (Human or Animal)
Or Chemical Emergency Assistance (Spill, Leak, Fire or Accident),
Call
1-800-888-8372
PRECAUTIONARY STATEMENTS
Hazards to Humans and Domestic Animals
CAUTION
Causes eye irritation. Harmful if swallowed or absorbed through skin. Avoid contact
with eyes, skin, or clothing. This product may cause skin sensitization reactions in
some people.

r shs-3-
Personal Protective Equipment
Applicators and other handlers must wear:
• Long-sleeved shjrt and long pants
• Chemical-resistant gloves, such as barrier laminate or Viton®
• Shoes plus socks
Follow manufacturer's instructions for cleaning/maintaining PPE. If no such instructions
for washables exist, use detergent and hot water. Keep and wash PPE separately from
other laundry.
Engineering Control Statements
Mixers and loaders supporting aerial applications are required to use closed systems.
The closed system must be used in a manner that meets the requirements listed in the
Worker Protection Standard (WPS) for agricultural pesticides [40 CFR 170.240(d)(4-6)].
When using the closed system, the mixers' and loaders' PPE requirements may be
reduced or modified as specified in the WPS.
When handlers use closed systems, enclosed cabs, or aircraft in a manner that meets
the requirements listed in the Worker Protection Standard (WPS) for agricultural
pesticides [40 CFR 170.240(d)(4-6)], the handler PPE requirements may be reduced or
modified as specified in the WPS.
User Safety Recommendations
Users should:
• Wash hands before eating, drinking, chewing gum, using tobacco, or using the
toilet.
• Remove clothing immediately if pesticide gets inside. Then wash thoroughly and put
on clean clothing.
• Remove PPE immediately after handling this product. Wash the outside of gloves
before removing. As soon as possible, wash thoroughly and change into clean
clothing.
Environmental Hazards
Do not apply directly to water, to areas where surface water is present, or to intertidal
areas below the mean high water mark. Do not contaminate water when disposing of
equipment wash water or rinsate.
Ground Water Advisory
The active ingredient in Medal II has the potential to leach through soil into ground
water under certain conditions as a result of agricultural use. Use of this chemical in

-4-
areas where soils are permeable, particularly where the water table is shallow, may
result in ground water contamination.
Surface Water Advisory
The active ingredient in Medal II has the potential to contaminate surface water through
ground spray drift. Under some conditions, the active ingredient may also have a high
potential for runoff into surface water (primarily via dissolution in runoff water) for
several months post-application. These include poorly drained or wet soils with readily
visible slopes toward adjacent surface waters, frequently flooded areas, areas
overlaying extremely shallow ground water, areas with in-field canals or ditches that
drain to surface water, areas not separated from adjacent surface waters with vegetated
filter strips, and areas overlaying tile drainage systems that drain to surface water.
Mixing/Loading Instructions
Care must be taken when using this product to prevent back-siphoning into wells, spills,
or improper disposal of excess pesticide, spray mixtures, or rinsates.
Check-valves or antisiphoning devices must be used on all mixing and/or irrigation
equipment.
This product may not be mixed or loaded within 50 ft. of perennial or intermittent
streams and rivers, natural or impounded lakes and reservoirs. This product may not
be mixed/loaded or used within 50 ft. of all wells, including abandoned wells, drainage
wells, and sink holes. Operations that involve mixing, loading, rinsing, or washing of this
product into or from pesticide handling or application equipment or containers within
50 ft. of any well are prohibited, unless conducted on an impervious pad constructed to
withstand the weight of the heaviest load that may be positioned on or moved across
the pad. Such a pad shall be designed and maintained to contain any product spills or
equipment leaks, container or equipment rinse or wash water, and rain water that may
fall on the pad. Surface water shall not be allowed to either flow over or from the pad,
which means the pad must be self-contained. The pad shall be sloped to facilitate
material removal. An unroofed pad shall be of sufficient capacity to contain at a
minimum 110% of the capacity of the largest pesticide container or application
equipment on the pad. A pad that is covered by a roof of sufficient size to completely
exclude precipitation from contact with the pad shall have a minimum containment
capacity of 100% of the capacity of the largest pesticide container or application
equipment on the pad. Containment capacities as described above shall be maintained
at all times. The above-specified minimum containment capacities do not apply to
vehicles when delivering pesticide shipments to the mixing/loading site.

-5-
CONDITIONS OF SALE AND LIMITATION OF WARRANTY AND LIABILITY
NOTICE: Read the entire Directions for Use and Conditions of Sale and Limitation of
Warranty and Liability before buying or using this product. If the terms are not
acceptable, return the product at once, unopened, and the purchase price will be
refunded.
The Directions for Use of this product must be followed carefully. It is impossible to
eliminate all risks inherently associated with the use of this product. Crop injury,
ineffectiveness or other unintended consequences may result because of such factors
as manner of use or application, weather or crop conditions, presence of other materials
or other influencing factors in the use of the product, which are beyond the control of
SYNGENTA CROP PROTECTION, LLC or Seller. To the extent permitted by
applicable law, Buyer and User agree to hold SYNGENTA and Seller harmless for any
claims relating to such factors.
SYNGENTA warrants that this product conforms to the chemical description on the label
and is reasonably fit for the purposes stated in the Directions for Use, subject to the
inherent risks referred to above, when used in accordance with directions under normal
use conditions. To the extent permitted by applicable law: (1) this warranty does not
extend to the use of the product contrary to label instructions or under conditions not
reasonably foreseeable to or beyond the control of Seller or SYNGENTA, and Buyer
and User assume the risk of any such use. TO THE EXTENT PERMITTED BY
APPLICABLE LAW, SYNGENTA MAKES NO WARRANTIES OF MERCHANTABILITY
OR OF FITNESS FOR A PARTICULAR PURPOSE NOR ANY OTHER EXPRESS OR
IMPLIED WARRANTY EXCEPT AS WARRANTED BY THIS LABEL.
To the extent permitted by applicable law, in no event shall SYNGENTA be liable for
any incidental, consequential or special damages resulting from the use or handling of
this product. TO THE EXTENT PERMITTED BY APPLICABLE LAW, THE
EXCLUSIVE REMEDY OF THE USER OR BUYER, AND THE EXCLUSIVE LIABILITY
OF SYNGENTA AND SELLER FOR ANY AND ALL CLAIMS, LOSSES, INJURIES OR
DAMAGES (INCLUDING CLAIMS BASED ON BREACH OF WARRANTY,
CONTRACT, NEGLIGENCE, TORT, STRICT LIABILITY OR OTHERWISE)
RESULTING FROM THE USE OR HANDLING OF THIS PRODUCT, SHALL BE THE
RETURN OF THE PURCHASE PRICE OF THE PRODUCT OR, AT THE ELECTION
OF SYNGENTA OR SELLER, THE REPLACEMENT OF THE PRODUCT.
SYNGENTA and Seller offer this product, and Buyer and User accept it, subject to the
foregoing Conditions of Sale and Limitation of Warranty and Liability, which may not be
modified except by written agreement signed by a duly authorized representative of
SYNGENTA.

-6-
DIRECTIONS FOR USE
It is a violation of federal law to use this product in a manner inconsistent with its
labeling.
Medal II should be used only in accordance with specifications on this label or in
separately published EPA accepted supplemental labeling recommendations for this
product.
Do not apply this product in a way that will contact workers or other persons, either
directly or through drift. Only protected handlers may be in the area during application.
For any requirements specific to your State or Tribe, consult the agency responsible for
pesticide regulation.
AGRICULTURAL USE REQUIREMENTS
Use this product only in accordance with its labeling and with the Worker Protection
Standard, 40 CFR part 170. This Standard contains requirements for the protection of
agricultural workers on farms, forests, nurseries, and greenhouses, and handlers of
agricultural pesticides. It contains requirements for training, decontamination,
notification, and emergency assistance. It also contains specific instructions and
exceptions pertaining to the statements on this label about personal protective
equipment (PPE) and restricted-entry interval. The requirements in this box only apply
to uses of this product that are covered by the Worker Protection Standard.
Do not enter or allow worker entry into treated areas during the restricted-entry
interval (REI) of 24 hours. Exception: If the product is soil-injected or soil-
incorporated, the Worker Protection Standard, under certain circumstances, allows
workers to enter the treated area if there will be no contact with anything that has been
treated.
PPE required for early entry to treated areas that is permitted under the Worker
Protection Standard and that involves contact with anything that has been treated, such
as plants, soil, or water is:
• Coveralls
• Chemical-resistant gloves, such as barrier laminate or Viton
• Shoes plus socks
FAILURE TO FOLLOW THE DIRECTIONS FOR USE AND PRECAUTIONS ON THIS
LABEL MAY RESULT IN POOR WEED CONTROL, CROP INJURY, OR ILLEGAL
RESIDUES.

C r <?(is -7- l
To avoid spray drift, do not apply under windy conditions. Avoid spray overlap, as crop
injury may result.
Note: It is illegal to sell, use or distribute this product within, or into, Nassau County or
Suffolk County, New York.
PRODUCT INFORMATION
Observe all precautions and limitations on the labels of each product used in tank
mixtures. Tank mixtures are permitted only in those states where the tank mix partner
is registered. Refer to and follow the label for each tank mix product used for
precautionary statements, directions for use, geographic and other restrictions.
Medal II is a herbicide recommended as a preplant surface-applied, preplant
incorporated, or preemergence treatment in water or fluid fertilizer for control of most
annual grasses and certain broadleaf weeds in corn (all types), cotton, peanuts, pod
crops, potatoes, safflowers, grain or forage sorghum, and soybeans.
When tank mixing or sequentially applying atrazine or products containing atrazine to
corn or sorghum do not exceed an application rate of 2.0 pounds active ingredient of
atrazine per acre for any single application and the total pounds of atrazine applied (Ib.
a.i. per acre) must not exceed 2.5 pounds active ingredient per acre per year.
Restriction: Do not use in nurseries, turf, or landscape plantings.
Do not apply under conditions which favor runoff or wind erosion of soil containing this
product to nontarget areas.
To prevent off-site movement due to runoff or wind erosion:
1. Avoid treating powdery dry or light sand soils when conditions are favorable for
wind erosion. Under these conditions, the soil surface should first be settled by
rainfall or irrigation.
2. Do not apply to impervious substrates, such as paved or highly compacted
surfaces.
3. Do not use tailwater from the first flood or furrow irrigation of treated fields to treat
nontarget crops, unless at least 1/4 inch of rainfall has occurred between
application and the first irrigation.
Where directions specify a Medal II tank mixture with AAtrex® formulations, other
brands of atrazine may be used. Follow the rates, recommendations, and limitations on
the AAtrex or respective atrazine product label, if other brands of atrazine are used.

-8-
Note: Certain states may have established rate limitations for atrazine within specific
geographical areas. Consult your state lead pesticide control agency for additional
information. It is a violation of this label to deviate from state use regulations.
If Medal II is incorporated, any supplemental tillage before planting must not exceed the
depth of incorporation.
Dry weather following an application of Medal II or a tank mixture may reduce
effectiveness. Cultivate if weeds develop.
Where reference is made to weeds partially controlled, partial control can either mean
erratic control from good to poor, or consistent control at a level below that generally
considered acceptable for commercial weed control.
SOIL TEXTURES AND HERBICIDE RATES
Where rates are based on coarse-, medium-, or fine-textured soils, it is understood that
soil textural classes are generally categorized as follows:
Coarse Medium Fine
Sand Loam Sandy clay loam
Loamy sand Silt loam Silty clay loam
Sandy loam Silt Clay loam
Sandy clay
Silty clay
Clay
Within rate ranges in the rate tables and elsewhere on this label, use the lowerVate on
soils relatively coarse-textured or low in organic matter; use the higher rate on soils
relatively fine-textured or high in organic matter.
Note: Medal II may be applied preemergence alone, or in combination with tank mix
partners specified on this label, following preplant incorporated herbicides when used
according to their label recommendations, provided that such use is not prohibited on
the respective labels.
Thoroughly clean sprayer or other application device before using. Dispose of cleaning
solution in a responsible manner. Do not use a sprayer or applicator contaminated with
any other materials, or crop damage or clogging of the application device may result.

C ((15-9-
MEDAL II APPLIED ALONE
WEEDS CONTROLLED
barnyardgrass foxtail millet signalgrass
(watergrass) galinsoga (Brachiaria)
bristly foxtail giant foxtail southwestern cupgrass
carpetweed goosegrass tall waterhemp
common waterhemp green foxtail wild proso millet*
crabgrass pigweed witchgrass
crowfootgrass prairie cupgrass woolly cupgrass*
Eastern black nightshade red rice yellow foxtail
fall panicum robust foxtails yellow nutsedge
Florida pusley (purple, white)
*For control of these weeds in corn only, refer to the Corn - Woolly Cupgrass and
Wild Proso Millet Control Program section of this label.
Weeds Partially Controlled*: common purslane, eclipta, Florida beggarweed**, hairy
nightshade, sandbur, seedling johnsongrass, shattercane, Texas panicum***, volunteer
sorghum, wild proso millet, and woolly cupgrass.
*See Product Information section. Control of these weeds can be erratic, due partially
to variable weather conditions. Control may be improved by following these suggested
procedures:
1. In corn, use 2.0-2.5 pts./A or the preplant surface-applied rates for Medal II
alone or in tank mixture, if allowed, when making preplant incorporated or
preemergence applications.
2. Thoroughly till moist soil to destroy germinating and emerged weeds. If Medal
II is to be applied preplant incorporated, this tillage may be used to incorporate
Medal II if uniform 2-inch incorporation is achieved as recommended under
Application Procedures.
3. Plant crop into moist soil immediately after tillage. If Medal II is to be used
preemergence, apply at planting or immediately after planting.
4. If available, sprinkler irrigate within 2 days after application. Apply 1/2-1 inch of
water. Use lower water volume (1/2 inch) on coarse-textured soils and higher
volume (1 inch) on fine-textured soils. Also, refer to the section on Center Pivot
Irrigation Application for this method of applying Medal II.

-10-
5. If irrigation is not possible and rain does not occur within 2 days after planting
and application, weed control may be decreased. Under these conditions, a
uniform, shallow cultivation is recommended as soon as weeds emerge.
**For partial control of this weed, use a minimum of 1.33 pts./A and apply
preemergence.
***For partial control of this weed, use a minimum of 1.33 pts./A and apply through a
center pivot irrigation system.
ROTATIONAL CROPS
Do not rotate to food or feed crops other than those listed below.
Medal II Alone: (1) If crop treated with Medal II alone is lost, any crop on this label may
be replanted immediately. Do not make a second broadcast application of Medal II. If
the original application was banded and the second crop is planted in the untreated row
middles, a second banded treatment may be applied. (2) Barley, oats, rye, or wheat
may be planted 4 1/2 months following treatment; alfalfa may be planted 4 months
following application. Tomatoes may be planted 6 months following application. (3) Any
crop on this label, in addition to root crops, tobacco, barley, buckwheat, milo, oats, rice,
rye, wheat, cabbage, or peppers, may be planted in the spring following treatment.
Clover may be seeded 9 months following application. Do not graze or feed forage or
fodder from cotton to livestock. (4) Following a lay-by treatment or multiple treatments
applied the previous season, any crop on this label, in addition to tobacco, cabbage,
peppers, stone fruits, or tree nuts, may be planted in the spring.
Medal II Tank Mixtures: For Rotational Crops restrictions for Medal II used in tank
mixtures, refer to the statements/restrictions above for Medal II and to the respective
product labels of any mixing partner(s) for additional statements/restrictions.
Important Notes: To avoid injury to rotational alfalfa or clover, (1) Do not apply more
than 1.9 Ibs. active ingredient per acre (2.0 pts. of Medal II) preemergence (including
preplant surface, preplant incorporated, postplant incorporated, etc.), and (2) Do not
make lay-by or other postemergent applications of Medal II.
APPLICATION PROCEDURES
Application Timing
Medal II alone or in some tank mixtures with other labeled herbicides may be applied for
weed control in certain crops at various times. Refer to the given crop section of the
label to determine if application timings listed below are recommended.

-11-
Preplant Surface-Applied: For minimum-tillage or no-tillage systems only, Medal II
alone and some Medal II tank mixtures may be applied up to 45 days before planting
certain crops. Use only split applications for treatments made 30-45 days before
planting, with 2/3 the recommended broadcast rate for the crop and soil texture applied
initially and the remaining 1/3 at planting. Treatments less than 30 days before planting
may be made either as a split or a single application. Refer to individual crop to
determine if early preplant surface application is recommended. If weeds are present at
the time of treatment, apply in a tank mixture combination with a contact herbicide (for
example, Gramoxone Inteon® or Roundup®). Observe directions for use, precautions,
and restrictions on the label of the contact herbicide. To the extent possible, do not
move treated soil out of the row or move untreated soil to the surface during planting, or
weed control will be diminished.
Preplant Incorporated: Apply Medal II to the soil and incorporate into the top 2 inches
of soil within 14 days before planting, using a finishing disk, narrow, rolling cultivator, or
similar implement capable of providing uniform 2-inch incorporation. Use a preplant
incorporated application if furrow irrigation is used or when a period of dry weather after
application is expected. If crop will be planted on beds, apply and incorporate Medal II
after bed formation, unless specified otherwise.
Preemergence: Apply Medal II during planting (behind the planter) or after planting,
but before weeds or crops emerge.
Postemergence: Medal II may be applied postemergence to corn, up to 40 inches tall.
Medal II will not provide postemergence weed control so it must be applied to a weed-
free soil surface or in combination with products that provide postemergence control of
weed species present at the time of application. Use only where allowed in crop
specific directions for use.
SPECIAL APPLICATION PROCEDURES
CA Only (Corn, Safflowers, Pod Crops): Preplant Incorporated: Broadcast Medal II
alone or with tank mix partners listed on this label to the soil and thoroughly incorporate
with a disk or similar implement set to till 4-6 inches deep. For more thorough
incorporation, till the soil in 2 different directions (cross-till). Crops may be planted on
flat surface or on beds. Caution should be used when forming the beds that only soil
from the Medal ll-treated zone is used (i.e., untreated soil should not be brought to soil
surface). If the application is made to preformed beds, incorporate Medal II with a tillage
implement set to till 2-4 inches deep. Care should be taken during tilling to keep the
tilled (Medal ll-treated) soil on the beds. Preemergence: Apply Medal II after planting.
Water with sprinkler or flood irrigation within 7-10 days.
Fall Application (Only in IA, MM, ND, SD, Wl, and portions of NE and IL - See
specific instructions in the Corn, Soybeans, and Pod Crops sections of this label
for timing of application and other information): Do not apply to frozen ground.
Use on medium and fine soils with greater than 2.5% organic matter that will be planted

-12-
to corn or soybeans the next spring. Ground may be tilled before or after application.
Do not exceed a 2 to 3-inch incorporation depth if tilled after treatment. Note: If a
spring application is made, the total rate of the fall plus spring applications must not
exceed the maximum total rate for the specific crop, or illegal residues may result.
Ground Application: Apply Medal II alone or in tank mixtures by ground equipment in
a minimum of 10 gals, of spray mixture per acre, unless otherwise specified.
Use sprayers that provide accurate and uniform application. For Medal II tank mixtures
with wettable powder or dry flowable formulations, screens and strainers should be no
finer than 50-mesh. Rinse sprayer thoroughly with clean water immediately after use.
Calculate the amount of herbicide needed for band treatment by the formula:
band width in inches x broadcast rate _ amount needed
row width in inches per acre per acre of field
For information on applying in lower volumes of carrier, see Low Carrier Application
section.
For application by air or through center pivot systems, see Aerial Drift Management
and Aerial Drift Reduction Advisory Information sections.
For information on impregnating dry fertilizer, see Dry Bulk Fertilizer section.
For information on application using variable-rate technologies, see Variable-Rate
Application section.
SPRAY EQUIPMENT
LOW CARRIER APPLICATION
For Broadcast Ground Application Only
Use sprayers, such as Ag-Chem RoGator®, Hagie, John Deere Hi-Cycle™, Melroe
Spra-Coupe, Tyler Patriot™, or Willmar Air Ride®, that provide accurate and uniform
application. Only water may be used as a carrier. Screens in suction and in-line
strainers should be 50-mesh. Manufacturers may require that tip screens as fine as
100-mesh be used with some nozzles. Use a pump with capacity to: (1) maintain up to
35-40 psi at the nozzles, and (2) provide sufficient agitation in tank to keep mixture in
suspension. Use a minimum of 5.0 gals, of spray mixture per acre. Maximum
recommended sprayer speed is 15 mph. Rinse sprayer thoroughly with clean water
immediately after each use.

-13-
Note: Low pressure nozzles are recommended to reduce drift and increase application
accuracy. Care should be taken when using automatic rate controlling devices to spray
the material within the rated working pressure and flow ranges of the nozzles selected.
Nozzle screens should be used when recommended by the manufacturer. All nozzles
should be placed on 20-inch centers, except flooding types which should be placed on
40-inch centers. When Flat Fan-type nozzles are used, angles of 80° or 110° are
recommended. Always read and follow the manufacturer's directions for optimum setup
and performance of their nozzles or tips.
AERIAL APPLICATION
Apply Medal II in water alone or in tank mixtures with AAtrex, Lexone®, Lorox®, or
Sencor® in a minimum total volume of 2.0 gals./A by aircraft. Medal II may also be
applied by air in combination with Balan®, Prowl®, or Treflan®. See specific tank
mixture sections for directions. Avoid application under conditions where uniform
coverage cannot be obtained or where excessive spray drift may occur. In order to
assure that spray will be controllable within the target area when used according to label
directions, make applications at a maximum height of 10 ft., using low-drift nozzles at a
maximum pressure of 40 psi, and restrict application to periods when wind speed does
not exceed 10 mph. To assure that spray will not adversely affect adjacent sensitive
nontarget plants, apply Medal II alone or Medal II + AAtrex by aircraft at a minimum
upwind distance of 400 ft. from sensitive plants, or apply Medal II + Lexone, Lorox, or
Sencor at a minimum upwind distance of 300 ft. from sensitive plants.
AERIAL DRIFT MANAGEMENT
The interaction of many equipment- and weather-related factors determine the potential
for spray drift. The applicator and the grower are responsible for considering all these
factors when making decisions.
The following drift management requirements must be followed to avoid off-target drift
movement from aerial applications to agricultural field crops. These requirements do
not apply to forestry applications, public health uses, or to applications using dry
formulations.
1. The distance of the outermost nozzles on the boom must not exceed 3/4 the length of
the wingspan or rotor.
2. Nozzles must always point backward parallel with the air stream and never be
pointed downward more than 45 degrees.
Where states have more stringent regulations, they must be observed.
The applicator should be familiar with and take into account the information covered in
the Aerial Drift Reduction Advisory Information section below.

-14-
Aerial Drift Reduction Advisory Information
Information on Droplet Size
The most effective way to reduce drift potential is to apply large droplets. The best drift
management strategy is to apply the largest droplets that provide sufficient coverage
and control. Applying larger droplets reduces drift potential, but will not prevent drift if
applications are made improperly, or under unfavorable environmental conditions (see
Wind, Temperature and Humidity, and Temperature Inversions).
Controlling Droplet Size
• Volume - Use high flow rate nozzles to apply the highest practical spray volume.
Nozzles with higher rated flows produce larger droplets.
• Pressure - Do not exceed the nozzle manufacturer's recommended pressures. For
many nozzle types, lower pressure produces larger droplets. When higher flow
rates are needed, use higher flow rate nozzles instead of increasing pressure.
• Number of nozzles - Use the minimum number of nozzles that provide uniform
coverage.
• Nozzle Orientation - Orienting nozzles so that the spray is released parallel to the
airstream produces larger droplets than other orientations and is the recommended
practice. Significant deflection from horizontal will reduce droplet size and increase
drift potential.
• Nozzle Type - Use a nozzle type that is designed for the intended application. With
most nozzle types, narrower spray angles produce larger droplets. Consider using
low-drift nozzles. Solid stream nozzles oriented straight back produce the largest
droplets and the lowest drift.
Application Height
Applications should not be made at a height greater than 10 ft. above the top of the
largest plants, unless a greater height is required for aircraft safety. Making applications
at the lowest height that is safe reduces exposure of droplets to evaporation and wind.
Swath Adjustment
When applications are made with a crosswind, the swath will be displaced downward.
Therefore, on the upwind and downwind edges of the field, the applicator must
compensate for this displacement by adjusting the path of the aircraft upwind. Swath
adjustment distance should increase with increasing drift potential (higher wind, smaller
drops, etc.).

C (
-15-
Wind
Drift potential is lowest between wind speeds of 2-10 mph. However, many factors,
including droplet size and equipment type, determine drift potential at any given speed.
Application should be avoided below 2 mph due to variable wind direction and high
inversion potential. Note: Local terrain can influence wind patterns.
Temperature and Humidity
When making applications in low relative humidity, set up equipment to produce larger
droplets to compensate for evaporation. Droplet evaporation is greatest when
conditions are both hot and dry.
Temperature Inversions
Applications should not occur during a temperature inversion because drift potential is
high. Temperature inversions restrict vertical air mixing, which causes small suspended
droplets to remain in a concentrated cloud. This cloud can move in unpredictable
directions due to the light variable winds common during inversions. Temperature
inversions are characterized by increasing temperatures with altitude and are common
on nights with limited cloud cover and light to no wind. They begin to form as the sun
sets and often continue into the morning. Their presence can be indicated by ground
fog; however, if fog is not present, inversions can also be identified by the movement of
smoke from a ground source or an aircraft smoke generator. Smoke that layers and
moves laterally in a concentrated cloud (under low wind conditions) indicates an
inversion, while smoke that moves upward and rapidly dissipates indicates good vertical
air mixing.
Sensitive Areas
The pesticide should only be applied when the potential for drift to adjacent sensitive
areas (e.g., residential areas, bodies of water, known habitat for threatened or
endangered species, nontarget crops) is minimal (e.g., when wind is blowing away from
the sensitive areas).
Avoid application to humans or animals. Flagmen and loaders should avoid inhalation
of spray mist and prolonged contact with skin.
CENTER PIVOT IRRIGATION APPLICATIONS
Medal II alone or in tank mixture with other herbicides on this label, which are registered
for center pivot application, may be applied in irrigation water preemergence (after
planting, but before weeds or crop emerge) at rates recommended on this label. Medal
II also may be applied postemergence to the crop and preemergence to weeds in crops
where postemergence applications are allowed on this label. Follow all restrictions
(height, timing, rate, etc.) to avoid illegal residues. Apply this product only through a

-16-
center pivot irrigation system. Do not apply this product through any other type of
irrigation system. Crop injury, lack of effectiveness, or illegal pesticide residues in the
crop can result from nonuniform distribution of treated water. If you have questions
about calibration, you should contact State Extension specialists, equipment
manufacturers, or other experts. Do not connect an irrigation system (including
greenhouse systems) used for pesticide application to a public water system, unless the
pesticide label-prescribed safety devices for public water systems are in place. A
person knowledgeable of the chemigation system and responsible for its operation, or
under the supervision of the responsible person, shall shut the system down and make
necessary adjustments should the need arise.
Operating Instructions
1. The system must contain a functional check-valve, vacuum relief valve, and low
pressure drain appropriately located on the irrigation pipeline to prevent water-
source contamination from backflow.
2. The pesticide injection pipeline must contain a functional, automatic, quick-
closing check-valve to prevent the flow of fluid back toward the injection pump.
3. The pesticide injection pipeline must also contain a functional, normally closed,
solenoid-operated valve located on the intake side of the injection pump and
connected to the system interlock to prevent fluid from being withdrawn from the
supply tank when the irrigation system is either automatically or manually shut
down.
4. The system must contain functional interlocking controls to automatically shut off
the pesticide injection pump when the water pump motor stops.
5. The irrigation line or water pump must include a functional pressure switch which
will stop the water pump motor when the water pressure decreases to the point
where pesticide distribution is adversely affected.
6. Systems must use a metering pump, such as a positive displacement injection
pump (e.g., diaphragm pump or piston pump), effectively designed and
constructed of materials that are compatible with pesticides and capable of being
fitted with a system interlock.
7. Do not apply when wind speed favors drift beyond the area intended for
treatment.
8. Prepare a mixture with a minimum of 1 part water to 1 part herbicide(s) and inject
this mixture into the center pivot system. Injecting a larger volume of a more
dilute mixture per hour will usually provide more accurate calibration of metering
equipment. Maintain sufficient agitation to keep the herbicide in suspension.

-17-
9. Meter into irrigation water during entire period of water application.
10. Apply in %-1 inch of water. Use the lower water volume (Vz inch) on coarse-
textured soils and the higher volume (1 inch) on fine-textured soils. More than 1
inch of water at application may reduce weed control by moving the herbicide
below the effective zone in the soil.
Precaution for center pivot applications: Where sprinkler distribution patterns do not
overlap sufficiently, unacceptable weed control may result. Where sprinkler distribution
patterns overlap excessively, crop injury may result.
DRY BULK GRANULAR FERTILIZERS
Many dry bulk granular fertilizers may be impregnated or coated with Medal II alone or
selected Medal II tank mixtures which are registered for preplant incorporated or
preplant surface application which are used to control weeds in crops on the Medal II
label and are not prohibited from use on dry bulk granular fertilizers.
When applying Medal II or Medal II mixtures with dry bulk granular fertilizers, follow all
directions for use and precautions on the respective product labels, regarding target
crops, rates per acre, soil texture, application methods (including timing of application),
and rotational crops.
All individual state regulations relating to dry bulk granular fertilizer blending,
registration, labeling, and application are the responsibility of the individual and/or
company selling the herbicide/fertilizer mixture.
Prepare the herbicide/fertilizer mixtures by using any closed drum, belt, ribbon, or other
commonly used dry bulk fertilizer blender. Nozzles used to spray Medal II and Medal II
mixtures onto the fertilizer must be placed to provide uniform spray coverage. Care
should be taken to aim the spray directly onto the fertilizer only and to avoid spraying
the walls of the blender.
If the herbicide/fertilizer mixture is too wet, add a highly absorptive material, such as
Agsorb® or Celatom MP-79®, or similar granular clay or diatomaceous earth materials,
to obtain a dry, free-flowing mixture. Absorptive materials should be added only after
the herbicide has been thoroughly blended into the fertilizer mixture. Best application
results will be obtained by using a granule of 6/30 particle size or of a size similar to that
of the fertilizer material being used. Generally, less than 2% by weight of absorptive
material will be needed. Avoid using more than 5% absorptive material by weight.

o -18-
Calculate amounts of Medal II, AAtrex, AAtrex + Princep®, Balance® Pro, Princep,
Sencor, Lexone, or Sonalan® by the following formula:
2.000 pts./A of liquid pts. of liquid or
Ibs. of fertilizer per X or flowable product = flow/able product per
acre ton of fertilizer
2.000 Ibs./A of dry Ibs. of dry product
Ibs. of fertilizer per X product = per ton of fertilizer
acre
Pneumatic (Compressed Air) Application (Medal II Alone): High humidity, high urea
concentrations, low fertilizer use rates, and dusty fertilizer may cause fertilizer mixture to
build up or plug the distributor head, air tubes, or nozzle deflector plates. To minimize
buildup, premix Medal II with Exxon Aromatic 200 at a rate of 1.0-4.0 pts./gal. of Medal
II. Aromatic 200 is a noncombustible/nonflammable petroleum product. Aromatic 200
may be used in either a fertilizer blender or through direct injection systems. Drying
agents should not be used when using Aromatic 200.
Notes: (1) Mixtures of Medal II and Aromatic 200 must be used on dry fertilizer only.
Poor results or crop injury may result if these mixtures are used in water or liquid
fertilizer solutions for spraying applications. (2) When impregnating Medal II in a
blender before application, a drier mixture can be attained by substituting a drying agent
for Aromatic 200. The use of Agsorb FG or drying agents of 6/30 particle size are
recommended. (3) Drying agents are not recommended for use with On-The-Go
impregnation equipment.
Restrictions: To avoid potential for explosion, (1) Do not impregnate Medal II or Medal
II mixtures on ammonium nitrate, potassium nitrate, or sodium nitrate, either alone or in
blends with other fertilizers. (2) Do not use Medal II or Medal II mixtures on straight
limestone, since absorption will not be achieved. Fertilizer blends containing limestone
can be impregnated.
Application
Apply 200-700 Ibs. of the herbicide/fertilizer mixture per acre. For best results, apply
the mixture uniformly to the soil with properly calibrated equipment immediately after
blending. Uniform application of the herbicide/fertilizer mixture is essential to prevent
possible crop injury. Nonuniform application may also result in unsatisfactory weed
control. In areas where conventional tillage is practiced, a shallow incorporation of the
mixture into the soil may improve weed control. On fine- or medium-textured soils in
areas where soil incorporation is not planned, i.e., reduced tillage situations or in some
conventional till situations, make applications approximately 30 days before planting to

r -19-
21
allow moisture to move the herbicide/fertilizer mixture into the soil. On coarse-textured
soils, make applications approximately 14 days prior to planting.
Restriction: To avoid crop injury, do not use the herbicide/fertilizer mixture on crops
where bedding occurs.
VARIABLE RATE APPLICATION
Variable-Rate Broadcast Ground Application for Corn and Soybeans
Variable-rate technologies may be used for more precise applications. Two additive
factors have been determined for use in applications using variable-rate technologies.
One of these factors (A) is directly related to soil texture and the other (B) is related to
percent organic matter (OM) and soil texture. When these two factors are added
together, the resulting application rate will be more precise for a soil of a given soil
texture and organic matter content. Use the formulas below to assure a more precise
rate for any given area within a field.
Formulas* for Preplant Surface-Applied, Preplant Incorporated, Preemergence,
and Early Preplant Applications
Refer to specific instructions regarding these applications in the Application
Procedures section of this label, as well as the appropriate crop section.
Soil Texture
COARSE
MEDIUM
FINE
Rates in Pints Per Acre
Preplant Surface-Applied
Preplant Incorporated
Preemergence
Factors
A B
1.0 + (0.1x%OM)
1.17 + (0.1x%OM)
1.33 + (0.1x%OM)
Early Preplant
Factors
A B
1.2 + (0.10 x%OM)
1.4 + (0.08 x%OM)
1.67 + (0.067 x % OM)
*Do not use on soils with greater than 8% organic matter (OM).
Formulas* for Fall Applications
This product is registered for use only where corn or soybeans will be grown the
following year in IA, MN, SD, ND, Wl, and portions of NE and IL. Refer to specific
instructions and restrictions regarding fall applications in the Corn and Soybeans
sections of this label.

-20-
Soil Texture
COARSE
MEDIUM
FINE
Rates in Pints Per Acre
Fall Applications
A
Factors
B
DO NOT USE
1.4
1.8
+ (0.113x%OM)
+ (0.067 x%OM).
*Do not use on soils with greater than 8% organic matter (OM).
MIXING INSTRUCTIONS
Medal II Alone: Mix Medal II with water or fluid fertilizer and apply as a spray. Fill the
spray tank 1/2-3/4 full with water or fluid fertilizer, add the proper amount of Medal II,
then add the rest of the water or fluid fertilizer. Provide sufficient agitation during mixing
and application to maintain a uniform emulsion.
Tank Mixtures: Fill the spray tank 1/4 full with water, and start agitation; add 2,4-D,
AAtrex, Balan, Balance Pro, Banvel®, Basagran®, Canopy®, Caparol® 4L,
Command®, Cotoran®, Eptam®, Gemini®, Lexone, Liberty® Herbicide, Liberty ATZ
Herbicide, Lorox, Lorox Plus®, Marksman®, Preview®, Princep, Prowl, Pursuit®,
AAtrex + Princep, Scepter®, Sencor, Sonalan, or Treflan, and allow it to become
dispersed; then add Medal II; then add Gramoxone Inteon, Landmaster® BW, or
Roundup (glyphosate products) if these products are being used; and finally the rest of
the water. For tank mixtures with AAtrex, Balance Pro, Banvel, Canopy, Caparol 4L,
Command, Cotoran*, Eptam, Gemini, Lexone, Lorox, Lorox Plus, Marksman, Preview,
Princep, Prowl*, Pursuit, AAtrex + Princep, Scepter, Sencor, Sonalan, or Treflan, fluid
fertilizers may replace all or part of the water as carrier, except in the AAtrex
postemergence and the Banvel postemergence tank mixes. For tank mixtures with
AAtrex, see additional mixing instructions on the AAtrex label. For each mixture, check
compatibility with fluid fertilizer, as described below, before mixing in spray tank. For all
tank mixtures, agitate during mixing and application to maintain a uniform suspension.
*See Special Mixing Instructions for tank mixtures with Cotoran, and with AAtrex or
Princep + Prowl under the appropriate tank mixture section.
For directions on how to conduct a compatibility test, see Compatibility Test section.
COMPATIBILITY TEST
Ajar test is recommended before tank mixing to ensure compatibility of Medal II with
other pesticides. The following test assumes a spray volume of 25 gals./A. For other
spray volumes, make appropriate changes in the ingredients.

-21-
Note: Nitrogen solutions or complete fluid fertilizers may replace all or part of the water
in the spray. Because liquid fertilizers vary, even within the same analysis, always
check compatibility with pesticide(s) before use. Incompatibility of tank mixtures is
more common with suspensions of fertilizer and pesticides.
Test Procedure
1. Add 1.0 pt. of carrier (fertilizer or water) to each of 2 one qt. jars with tight lids. Note:
Use the same source of water that will be used for the tank mix and conduct the test
at the temperature the tank mix will be applied.
2. To one of the jars, add % tsp. or 1.2 milliliters of a compatibility agent approved for
this use, such as Compex or Unite (1/4 tsp. is equivalent to 2.0 pts./100 gals, spray).
Shake or stir gently to mix.
3. To both jars, add the appropriate amount of pesticide(s) in their relative proportions
based on recommended label rates. If more than one pesticide is used, add them
separately with dry pesticides first; flowables next, and emulsifiable concentrates
last. After each addition, shake or stir gently to thoroughly mix.
4. After adding all ingredients, put lids on and tighten, and invert each jar ten times to
mix. Let the mixtures stand 15-30 minutes and then look for separation, large flakes,
precipitates, gels, heavy oily film on the jar, or other signs of incompatibility.
Determine if the compatibility agent is needed in the spray mixture by comparing the
two jars. If either mixture separates, but can be remixed readily, the mixture can be
sprayed as long as good agitation is used. If the mixtures are incompatible, test the
following methods of improving compatibility: (a) Slurry the dry pesticide(s) in water
before addition, or (b) add 1/4 the compatibility agent to the fertilizer or water and the
other !4 to the emulsifiable concentrate or flowable pesticide before addition to the
mixture. If incompatibility is still observed, do not use the mixture.
5. After compatibility testing is complete, dispose of any pesticide wastes in
accordance with the Storage and Disposal section in this label.
CROP USE DIRECTIONS
CORN (ALL TYPES) - MEDAL II ALONE
Apply Medal II, either preplant surface, preplant incorporated, preemergence,
postemergence, or lay-by, using the appropriate rate specified below.
PREPLANT SURFACE APPLIED
Refer to instructions for use of Medal II alone under Application Procedures.

r -22-
Fall Application:
1. Apply after September 30 in ND, SD, MN, Wl, and north of Route 30 in IA.
2. Apply after October 15 north of Route 91 in NE and south of Route 30 in IA.
3. Apply after October 31 north of Route 136 in IL.
In all locations, apply to crop stubble after harvest when the sustained soil temperature
at a 4-inch depth is less than 55°F and falling. In minimum-till or no-tillage systems on
soils having greater than 2.5% organic matter, use 1.67-2.0 pts./A on medium-textured
and 2.0 pts./A on fine-textured soils. Do not apply to frozen ground. A tillage operation
may precede the application. A fall and/or a spring tillage may follow application, but do
not exceed an incorporation depth greater than 2-3 inches. Minimize furrow and ridge
formation in the tillage operations. Note: If a spring application is made, the total rate
of the fall plus spring applications must not exceed the maximum total rate for corn, or
illegal residues may result.
Use on medium- and fine-textured soils with minimum-tillage or no-tillage systems in
CO, IA, IL, IN, KS, KY, MN, MO, MT, ND, NE, SD, TN, Wl, and WY. Apply 2/3 the
recommended rate of Medal II (1.67 pts./A on medium soils and 2.0 pts./A on fine soils)
as a split treatment 30-45 days before planting and the remainder at planting.
Applications made less than 30 days prior to planting may be as either a split or single
treatment. Apply 1.33 pts./A on coarse soils not more than 2 weeks before planting.
On medium- and fine-textured soils with minimum- or no-tillage systems in CT, DE, MA,
MD, ME, Ml, NH, NY, OH, PA, Rl, VA, VT, and WV, preplant surface applications may
be applied following the directions for use above. If the amount of rainfall results in
unsatisfactory length of weed control following the earlier treatment, a postemergence
application of an appropriately labeled broadleaf and/or grass weed herbicide may be
used, i.e., AAtrex, Beacon®, Bicep® MAGNUM, Bicep II MAGNUM®, Exceed®,
Accent®, Banvel, Basagran, bromoxynil (Brominal® or Buctril®), or 2,4-D. If the
postemergence treatment includes the herbicide used preplant surface-applied, do not
exceed the total labeled rate for corn on a given soil texture. Observe all directions for
use, precautions, and limitations on the label of the postemergent herbicide.
PREPLANT INCORPORATED OR PREEMERGENCE
Follow instructions for use of Medal II alone under Application Procedures. On
coarse soils, apply 1.0-1.33 pts./A of Medal II if organic matter content is less than 3%,
or 1.33 pts./A if organic matter content is 3% or greater. On medium soils, apply 1.33-
1.67 pts./A of Medal II. On fine soils, apply 1.33-1.67 pts./A of Medal II if organic matter
content is less than 3%, or 1.67-2.0 pts./A if organic matter content is 3% or greater.
POSTEMERGENCE OR LAYBY
To extend the duration of weed control in corn, a maximum rate of 2.0 pts./A of Medal II
may be applied after corn emergence until the corn plants reach 40 inches in height,

r-23-
following any preplant surface-applied, preplan! incorporated, or preemergence
herbicide application, including Medal II. For best results, applications should be made
to soil free of emerged weeds and directed toward the base of corn plants in excess of 5
inches tall. The total Medal II rate applied on corn during any one crop year should not
exceed 3.9 pts./A.
Note for all applications to corn: To avoid possible illegal residues(1) do not graze or
feed forage from treated areas for 30 days following application and (2) do not harvest
sweet corn ears from treated areas for 30 days following last application.
PROBLEM WEED CONTROL DIRECTIONS
Shattercane, Wild Proso Millet, Woolly Cupgrass, and Eclipta - Partial Control:
For more consistent partial control of shattercane, wild proso millet, woolly cupgrass, or
eclipta, apply 2.0-2.5 pts./A as a single application; or apply 1.0-1.33 pts./A of Medal II
preplant incorporated followed by 1.0-1.33 pts./A of Medal II preemergence; however,
do not apply more than a total of 2.5 pts./A. Make the preemergence application during
or after planting, but before weeds and corn emerge. Apply the 1.33 pts./A rate of
Medal II when a heavy infestation of shattercane, wild proso millet, woolly cupgrass, or
eclipta is expected. A shallow cultivation may be needed to control any late emerging
weeds.
Woolly Cupgrass and Wild Proso Millet Control Program: For control of these
species, use the following 3-step program: (1) Apply Medal II early preplant, preplant
incorporated, or preemergence at 1.67 pts./A on medium soils and 2.0 pts./A on fine-
textured soils, up to the maximum label rate. Lightly incorporate with a rotary hoe if
rainfall does not occur within 5-7 days; (2) Apply a postemergence tank mix of Beacon
at 0.38 oz./A or Exceed at 1 packet per 4 acres plus Accent SP at 0.33 oz./A plus 1.0 qt.
of crop oil concentrate plus 1.0 gal./A of 28% nitrogen, or the equivalent amount of
ammonium sulfate, when grasses are 2-3 inches tall and the corn is at least 4 inches
tall; and (3) Cultivate 14-21 days after the postemergence application.
MEDAL II PROGRAMS FOR PLANNED TWO-PASS WEED CONTROL SYSTEMS IN
ROUNDUP READY® AND GLYPHOSATE TOLERANT CORN
Medal II may be applied preplant incorporated or preemergence in Roundup Ready or
glyphosate tolerant corn at rates down to 1.0 pts./A on all soils when followed by a
planned postemergence application of an approved glyphosate based product -
examples include Touchdown and Roundup UltraMax. Follow all other directions for
use, precautions and restrictions listed for Medal II on this label. The glyphosate
product must be registered for postemergence applications in Roundup Ready or
glyphosate tolerant corn and be applied according to the weed and crop timings,
methods, precautions and restrictions listed on the glyphosate containing product label.
When used in this way, Medal II will provide reduced competition of the weeds listed as
controlled in the Product Information section of this label for a period of 30 or more

-24-
days, thus improving the timing flexibility and effectiveness of the glyphosate based
product application.
Restrictions and Precautions: (1) Do not apply more than the labeled application rate
for a given soil texture per year, either as a single or split treatment, or illegal residues
may result. (2) In corn, Medal II may be used up to 2.5 pts./A as either a preplant
surface, preplant incorporated, or preemergence treatment on soils having an organic
matter content between 6% and 20% or up to 2.0 pts./A on any soil for extended
residual control and where severe stands of problem weeds are expected. (3) In the
event of escape of annual weeds following a preplant surface, preplant incorporated, or
preemergence treatment of Medal II, follow with a postemergence application of an
appropriately labeled broadleaf and/or grass weed herbicide, i.e., AAtrex, Beacon, Bicep
MAGNUM, Bicep II MAGNUM, Bicep Lite II® MAGNUM, Exceed, Accent, Banvel,
Basagran, Brominal, Buctril, or 2,4-D. If the postemergence treatment includes the
herbicide used in the earlier treatment, i.e., AAtrex, do not exceed the total labeled rate
for corn on a given soil texture. (4) Brominal or Buctril may be applied postemergence
alone or in tank mix combination with AAtrex. Do not exceed 1.2 Ibs. a.i./A of AAtrex in
tank mix combination with Brominal or Buctril postemergence. Refer to the AAtrex,
Brominal, and Buctril labels for specific rates and precautions. (5) Do not use Medal II
on peat or muck soils.
CORN - MEDAL II COMBINATIONS
Medal II in any tank mixture for corn may be applied in water or fluid fertilizer before
corn emerges. Use only water as a carrier when Medal II is applied after corn
emergence.
Restrictions: For all applications to corn, (1) do not graze or feed forage from treated
areas for 30 days following application, or possible illegal residues may result and (2) do
not harvest sweet corn ears from treated areas for 30 days following application. (3) The
total Medal II rate applied on corn during any one crop year must not exceed 3.9 pts./A.
IMPORTANT: FOR TANK MIXTURES WITH AATREX (OR OTHER BRANDS OF
ATRAZINE) - If applying Medal II in tank mixture with AAtrex, all the restrictions
and rate limitations on the AAtrex label must be followed if more
restrictive/protective than those on this label. In addition, if AAtrex is/must be
applied at rates lower than those specified on this label, broadleaf weed control
may be affected. Refer to the AAtrex label for weeds controlled at the reduced
rates.

-25-
Chart 1: Medal II Tank Mixtures for Corn - Additional Weeds Controlled and
Special Instructions
Special Mixing
Instructions
Comments
Browntop panicum
Cocklebur
Common purslane
Hairy nightshade
Jimsonweed
Kochia
Lambsquarters
Morningglory
Mustard
Pigweed
Prickly sida
Ragweed
Smartweed
Velvetleaf
Medal II
+ AAtrex and/
or Princep
(Preplant
Surface, PPI,
PRE)
2,3,4,5,7,8
X
X
X
X
X
X
X
X
X
Medal II
+ AAtrex
(Post)
2,3,4,5
0
X
X
X
0
X
X
X
X
X
Medal II +
Banvel
(Field Corn)
0
0
X
0
X
X
0
Medal II +
AAtrex +
Lorox
2,3,4,5,6
X
X
X
X
X
X
X
X
X
X
Medal II +
AAtrex or
Princep +
Prowl
1
•2,3,4,5
X
X
X
X
X
X
X
X
X
X
Medal II
+
Balance PRO*
2,3,7
X
X
X
X
X
X
X
X
o-x
X = control; 0 = partial control; O-X = partial to full control depending on ratio of products used or on weed population
*Field corn only
Comments
1. Special Mixing Instructions for Medal II + AAtrex or Princep and Prowl
(1) Fill the spray tank % full with water or fluid fertilizer and start agitation. (2) To
aid compatibility, add a compatibility agent, such as Unite orX-77®, at 4.0
pts./100 gals, of spray mixture. (3) Then add the AAtrex or Princep and allow it
to become dispersed. (4) Then add Medal II and Prowl 4E. (5) Add the rest of
the water.
2. Although a single formulation for AAtrex or Princep is listed in the rate tables,
other formulations may be substituted, using the following formula:

-26-
• 1.0 Ib. of AAtrex Nine-O® or Princep Caliber 90® =
1.8 pis. of AAtrex 4L or Princep 4L
3. Although directions specify AAtrex formulations in tank mixture with Medal II,
other brands of atrazine may be used. Follow the rates, recommendations, and
limitations on the atrazine label.
4. See additional mixing instructions on the AAtrex label.
5. Restriction: Do not exceed a total of 2.5 Ibs. a./, of atrazine per acre per year.
However, certain states may have established rate limitations for atrazine within
specific geographical areas. Consult your state lead pesticide control agency for
additional information. It is a violation of this label to deviate from state use
regulations.
6. Other formulations of Lorox can be used: 1.0 Ib. of Lorox DF = 1.0 pt. of Lorox L.
7. In Minimum-Tillage and No-Tillage systems, mix with Gramoxone Inteon for
control of most emerged annual weeds and suppression of perennial weeds; or
with Landmaster BWfor suppression of emerged field bindweed and control or
suppression of annual weeds; or with Roundup for control of most emerged
annual and perennial weeds.
8. Refer to the Corn - Medal II Magnum Combinations - Tank Mixture with
AAtrex; or AAtrex + 2,4-D or AAtrex+ 2,4-D + Banvel for Minimum Tillage or
No-Tillage Systems sections for specific directions for 2,4-D or Banvel
burndown combinations in Minimum-Tillage and No-Tillage systems.
Medal II in any tank mixture for corn may be applied in water or fluid fertilizer,
except as noted.
Restrictions: (1) For all applications to corn, do not graze or feed forage from treated
areas for 30 days following application, and do not harvest sweet corn ears from treated
areas for 30 days following application or possible illegal residues may result. (2) When
applying Medal II in tank mixture with AAtrex, do not exceed a total of 2.5 Ibs. a.i. of
atrazine per acre per year. (3) Refer to Corn (All Types) - Medal II Alone, Note 3 for
recommended sequential postemergence treatments if escape weeds develop. (4) In
corn, Medal II may be used up to 2.0 pts./A in combinations on any soil for extended
residual control and where severe stands of problem weeds are expected.
TANK MIXTURE WITH AATREX OR PRINCEP, OR AATREX + PRINCEP -
PREPLANT SURFACE, PREPLANT INCORPORATED, OR PREEMERGENCE
In addition to the weeds controlled by Medal II alone, Medal II + AAtrex or Princep, or
Medal II + AAtrex + Princep, applied preplant surface, preplant incorporated, or
preemergence, also controls the following weeds: browntop panicum, cocklebur,

-27-
common purslane, hairy nightshade, lambsquarters, morningglory, ragweed,
smartweed, and velvetleaf.
Apply Medal II + AAtrex or Princep, or Medal II + AAtrex + Princep either preplant
surface, preplant incorporated, or preemergence.
Preplant Surface-Applied: Follow instructions for use of Medalll alone under
Application Procedures and under application instructions for Medal II alone on corn.
Apply Medal II + AAtrex or Princep, or Medal II + AAtrex + Princep on medium soils
(1.67 pts./A of Medal II + 3.2-4.0 pts./A of AAtrex 4L or Princep 4L, or AAtrex 4L +
Princep 4L combined) and on fine soils (1.67-2.0 pts./A of Medal II + 4.0-pts./A of
AAtrex 4L or 4.0-5.0 pts./A of Princep 4L, or AAtrex 4L + Princep 4L combined) in
minimum-tillage and no-tillage systems in CO, IA, IL, IN, KS, KY, MN, MO, MT, ND,
NE, SD, TN, Wl, and WY. Apply the tank mixtures as a split or single treatment in those
states and as indicated in the Medal II Alone - Preplant Surface-Applied section of
the label for corn. On coarse soils, apply 1.33 pts./A of Medal II and 3.2 pts./A of AAtrex
4L or Princep 4L, or AAtrex 4L + Princep 4L combined.
Preplant Incorporated or Preemergence: Follow instructions for use of Medal II alone
under Application Procedures. Apply Medal II + AAtrex or Princep, or Medal II +
AAtrex + Princep, using the appropriate rates from Table 1.
Restriction: Do not apply more than the labeled rate for a given soil texture per year,
either as a split or single treatment, or illegal residues may result.
Shattercane, Wild Proso Millet, Woolly Cupgrass, and Eclipta - Partial Control
For more consistent partial control of shattercane, wild proso millet, woolly cupgrass, or
eclipta, where Medal II is applied in tank mixture or sequentially with other registered
corn herbicides, apply 2.0-2.33 pts. as a single application, or the following applications
may be made:
1. Apply 1.0-1.33 pts./A of Medal II + 2.0 Ibs. a.i./A of AAtrex or Princep preplant
incorporated, followed by 1.0-1.33 pts./A of Medal II preemergence. Make the
preemergence application during or after planting, but before weeds and corn
emerge.
2. Apply Medal II at 1.33 pts./A alone or in tank mix combination with up to 2.0 Ibs.
a.i./A of AAtrex, or Princep, preplant incorporated. Do not exceed the total rate
of triazine herbicide recommended for corn grown on a given soil texture. Follow
with a post-directed application of Evik® SOW at 2.5 Ibs./A. Refer to the Evik SOW
label for specific directions for the post-directed application.

-28-
3. Apply Eradicane® or (or equivalent EPTC or butylate formulations) at labeled
rates preplant incorporated, followed by a preemergence application of Medal II
at 1.0-1.33 pts./A. Do not use Eradicane or on soils where rapid degradation has
been shown to occur. Make the preemergence application during or after
planting, but before weeds and corn emerge.
Precaution: When following the application regimes in numbers 1-3 above, a shallow
cultivation may be needed after the preemergence or postemergence application to help
control any late emerging shattercane or wild proso millet plants.
Table 1: Medal II + AAtrex or Princep, or Medal II + AAtrex + Princep, Preplant
Incorporated or Preemergence - Corn (All Types)
Soil Texture
COARSE
MEDIUM
FINE
Muck or Peat
(soils with more
than 20%
organic matter)
Broadcast Rates Per Acre
Less than 3% Organic Matter
Medal II +
AAtrex
Nine-O* OR
or
Princep
Caliber 90*
0.8-1 .Opt.
1.1-2.2 Ibs.
1.0-1 .33 pts.
1.3-2.2 Ibs.
1 .33 pts.
1.8-2.2 Ibs.
Medal II +
AAtrex
Nine-O**
Princep
Caliber 90**
0.8-1 .Opt.
0.6-1.1 Ibs.
0.6-1.1 Ibs.
1.0-1 .33 pts.
0.7-1.1 Ibs.
0.7-1.1 Ibs.
1 .33 pts.
0.9-1.1 Ibs.
0.9-1.1 Ibs.
3% Organic Matter or Greater
Medal II +
AAtrex
Nine-O* OR
or
Princep
Caliber 90*
1 .0 pt.
1.3-2.2 Ibs.
1.33 pts.
1.8-2.2 Ibs.
1.33-1 .67 pts.
1.8-2.2 Ibs.***
Medal II +
AAtrex
Nine-O*
Princep
Caliber 90*
1.0pt.
0.7-1.1 Ibs.
0.7-1.1 Ibs.
1 .33 pts.
0.9-1.1 Ibs.
0.9-1.1 Ibs.
1.33-1 .67 pts.
0.9-1.1 Ibs.***
0.9-1.1 Ibs.***
DO NOT USE
"Use Princep in preference to AAtrex when heavy infestations of crabgrass or fall
panicum are expected. On soils having between 6% and 20% organic matter,
Medal II may be used up to 2.33 pts./A in tank mix combination with 2.2 Ibs./A of
AAtrex Nine-O, or equivalent rates of AAtrex 4L. Refer to the AAtrex label for
weeds controlled at this reduced rate.

-29-
**When using the tank mixture of Medal II + AAtrex Nine-O + Princep Caliber 90, use
equal rates of each as shown when heavy broadleaf weed infestations are
expected. When heavy infestations of crabgrass or fall panicum are expected, use a
1:2 ratio of AAtrex + Princep instead of the 1:1 ratio given in Table 1. (Example'.
Total AAtrex Nine-O + Princep Caliber 90 = 1.2 Ibs./A, use 0.4 Ib. of AAtrex + 0.8 Ib.
of Princep, respectively.) Refer to Comment No. 3 following Chart 1 for AAtrex 4L
and Princep 4L conversions.
***For cocklebur, yellow nutsedge, and velvetleaf control on fine-textured soils above
3% organic matter, apply 2.25 Ibs./A of AAtrex Nine-O, or equivalent rates of AAtrex
4L, or the same total amount of AAtrex + Princep with 1.33-1.67 pts./A of Medal II.
TANK MIXTURE WITH AATREX - POSTEMERGENCE
Weeds Controlled Weeds Partially Controlled
barnyardgrass cocklebur
(watergrass) morningglory
crabgrass yellow nutsedge
crowfootgrass
fall panicum
giant foxtail
green foxtail
yellow foxtail
jimsonweed
kochia
lambsquarters
mustard
pigweed
prickly sida
purslane
ragweed
smartweed
velvetleaf
Apply 1.0 pt./A of Medal II + 1.3 Ibs./A of AAtrex Nine-O* on coarse so/7s, 1.33 pts./A of
Medal II + 1.8 Ibs./A of AAtrex Nine-O on medium soils, or 1.33-1.67 pts./A of Medal II +
1.8-2.2 Ibs./A** of AAtrex Nine-O on fine soils. Apply this tank mixture before grass and
broadleaf weeds pass the 2-leaf stage and before corn exceeds 5 inches in height.
Application to weeds larger than the 2-leaf stage will generally result in unsatisfactory
control.
Lay-by: Apply to corn plants not more than 12 inches tall. Applications to corn in
excess of 5 inches should be directed to the base of the corn plants; whereas,
applications to corn plants less than 5 inches tall may be made over the top.

-30-
Occasionally, some corn leaf burn may result, but this should not affect later growth or
yield. Do not apply this postemergence tank mixture in fluid fertilizer, or severe crop
injury may occur.
*When using AAtrex 4L, use equivalent rates. One Ib. of AAtrex Nine-O = 1.8 pts. of
AAtrex 4L
**For better control of cocklebur, morningglory, velvetleaf, and yellow nutsedge on fine-
textured soils above 3% organic matter, apply 2.2 Ibs./A of AAtrex Nine-O, or
equivalent rate of AAtrex 4L, with 1.33-1.67 pts./A of Medal II.
Tank mixtures of Medal II + AAtrex may be applied following use of any registered
preplant surface-applied, preplant incorporated, or preemergence corn herbicide,
including Medal II + AAtrex.
Note: The total Medal II rate should not exceed 3.9 pts., nor the AAtrex rate more than
2.5 Ibs. a.i./A during any one crop year, or illegal residues may result. Refer to the
AAtrex label for geographic, soil-texture, and rotational restrictions.
TANK MIXTURE WITH BANVEL
Preemergence: Use this tank mixture only on field corn which is flat-planted (no
furrows) in CO, IA, IL, IN, KS, MN, NE, OH, SD, and Wl.
In addition to the weeds controlled by Medal II alone, Medal II + Banvel, applied
preemergence, also controls lambsquarters, ragweed, smartweed, cocklebur*,
jimsonweed*, morningglory*, and velvetleaf*.
*Partially controlled.
Apply Medal II + Banvel preemergence. Broadcast 1.0 pt./A of Banvel with 1.33 pts./A
of Medal II on medium soils, or with 1.33-1.67 pts./A of Medal II on fine soils. Do not
apply on coarse so/7s or on soils with less than 2.5% organic matter. Apply this tank
mixture to the soil surface at planting or after planting, but before corn emerges. Plant
corn at least 1.5 inches deep and apply behind planting equipment, avoiding
incorporation by the planter wheel or other seed covering device. Do not incorporate
before corn emergence. If it is necessary to rotary hoe to break the soil crust, do not
disturb the soil more than Y2 inch deep.
Restrictions and Precautions: (1) Avoid drift to sensitive nontarget plants, such as
soybeans, during application, or injury may occur. (2) Do not apply with aircraft.
Postemergence for Control of Pigweed (Mid-Atlantic states, including DE, MD, PA,
VA, and WV): Apply 1.0-1.5 pts./A of Medal II + 0.5-1.0 pt./A of Banvel by ground
equipment when pigweed plants are less than 3 inches tall and before corn exceeds 5
inches in height in a minimum of 20 gals, of spray per acre. Use the lower rate on

-31-
coarse-textured and low organic matter soils. Use the higher rate on fine-textured and
high organic matter soils.
Banvel SGF® and Clarity® may be used at equivalent Ibs. of active ingredient per acre.
Restrictions and Precautions: (1) Avoid drift to sensitive nontarget plants, such as
soybeans, during application, or injury may occur. (2) Do not apply with aircraft.
TANK MIXTURE WITH AATREX AND LOROX FOR CONTROL OF
LAMBSQUARTERS AND PIGWEED
For prolonged control of lambsquarters and pigweed in DE, MD, NJ, NY, PA, VA, and
VW, Medal II may be applied preemergence in tank mix combination with AAtrex +
Lorox. Apply Medal II and AAtrex according to the rates in Table 1 and Lorox according
to the following rates.
Soil Texture
Sandy loam (1-3% organic matter)
Sandy loam (3-6% organic matter)
Medium- and fine-textured soils (1-6% organic matter)
Broadcast Rate Per Acre
0.67 Ib. Lorox
1.0 Ib. Lorox
1.0 Ib. Lorox
When using Lorox L or Lorox DF, use equivalent rates. One pt. of Lorox L equals 1.0
Ib. of Lorox DF.
Observe all directions for use, precautions, and limitations on the Medal II, AAtrex, and
Lorox labels when applying these products in tank mix combinations.
TANK MIXTURE WITH AATREX OR PRINCEP + PROWL FOR PROLONGED
CONTROL OF LAMBSQUARTERS AND PIGWEED IN FIELD CORN ONLY
(NORTHEAST U.S., INCLUDING Ml, IN, KY, AND STATES EAST OF THESE)
For prolonged control of lambsquarters and pigweed, in addition to a broad spectrum of
annual broadleaf and grass weeds, Medal II in tank mix combination with AAtrex* or
Princep + Prowl 4E may be applied after planting, but before corn or weeds emerge.
Apply by ground equipment in a minimum of 10 gals, of water or 20 gals, of liquid
fertilizer. Apply by air in a minimum of 5.0 gals, of water. Refer to Table 1 of this label
for rates of Medal II, AAtrex, or Princep to be applied. Apply Prowl 4E according to the
rates in Table 2.
*Do not apply Medal II in tank mix combination with AAtrex 80W+ Prowl, as this
combination is not compatible. Other AAtrex formulations may be used.
Mixing Instructions: See Comment No. 1 following Chart 1.

-32-
Table 2: Prowl 4E - Broadcast Rates Per Acre
Soil Texture
COARSE
MEDIUM
FINE
Percent Organic Matter in Soil
Less Than 1 .5%
1. 5-2.0 pts.
2.0 pts.
2.0 pts.
1.5-3%
2.0 pts.
3.0 pts.
3.0 pts.
Over 3%
3.0 pts.
3.0 pts.
3.0 pts.
Observe all directions for use, precautions, and limitations on the respective product
labels when applying these products in tank mix combination. Refer to the Prowl 4E
label for replanting instructions in the event of crop loss.
TANK MIXTURE OF MEDAL II WITH AATREX OR PRINCEP, OR AATREX +
PRINCEP WITH GRAMOXONE INTEON, LANDMASTER BW, OR ROUNDUP FOR
MINIMUM-TILLAGE OR NO-TILLAGE SYSTEMS
In minimum-tillage or no-tillage systems where corn is planted directly into a cover crop,
stale seedbed, established sod, or previous crop residues, the contact herbicides
Gramoxone Inteon, Landmaster BW, or Roundup should be tank mixed with Medal II,
Medal II + AAtrex, Medal II + Princep, or Medal II + AAtrex + Princep. See Comment
No. 7 following Chart 1. The Medal II, Medal II + AAtrex or Princep, or Medal II +
AAtrex + Princep portion of the tank mixture provides preemergence control of the
weeds listed on this label in the tank mixture section for Medal II, Medal II + AAtrex or
Princep, or Medal II + AAtrex + Princep - Preplant Surface, Preplant Incorporated,
or Preemergence.
Application: Apply before, during, or after planting, but before the corn emerges, at the
rates specified below. Add Gramoxone Inteon, Landmaster BW, or Roundup at the
following broadcast rates:
Gramoxone Inteon: 1.5-2.0, 2.0-2.5, or 2.5-3.0 pts./A to 1-3, 3-6, or 6-inch tall weeds,
respectively. Apply surfactant at 1.0 or 2.0 pts./100 gals, of spray mixture with 75% or
greater or 50-74% nonionic active ingredient, respectively. This treatment will not
control weeds taller than 6 inches.
Restriction: Do not apply combinations containing Gramoxone Inteon in suspension-
type liquid fertilizers, as the activity of paraquat will be reduced.
Landmaster BW: 27-54 oz./A depending on weed species and size. See the
Landmaster BW label for weeds controlled, recommended rates for specific weeds, and
other information concerning use.
Roundup: See the Roundup or Roundup RT label for weeds controlled, recommended
rates, and other use directions.
Apply in 20-60 gals, of water or fluid fertilizer per acre with ground equipment.

-33-
On coarse soils, apply 1.0 pt./A of Medal II with 1.3 \bs. of AAtrex Nine-O* or Princep
Caliber 90*, or with 0.7 Ib. of AAtrex Nine-O** + 0.7 Ib. of Princep Caliber 90**. On
medium soils, apply 1.33 pts./A of Medal II with 1.8 Ibs. of AAtrex Nine-O or Princep
Caliber 90, or with 0.9 Ib. of AAtrex Nine-O + 0.9 Ib. of Princep Caliber 90. On fine
soils***, apply 1.33-1.67 pts./A of Medal II with 1.8-2.2 Ibs. of AAtrex Nine-O or Princep
Caliber 90, or with 0.9-1.1 Ibs. of AAtrex Nine-O + 0.9-1.1 Ibs. of Princep Caliber 90.
*Use Princep in preference to AAtrex when heavy infestations of crabgrass or fall
panicum are expected.
**When using the tank mixture of Medal II + AAtrex Nine-O + Princep Caliber 90, use
equal rates of AAtrex and Princep as shown when heavy broadleaf weed
infestations are expected. When heavy infestations of crabgrass or fall panicum are
expected, use a 1:2 ratio of AAtrex + Princep instead of the 1:1 ratio given.
(Example: Total AAtrex Nine-O + Princep Caliber 90 = 1.8 Ibs./A, use 0.6 Ib. of
AAtrex +1.2 Ibs. of Princep, respectively.) Refer to Comment No. 2 following Chart
1 for AAtrex 4L and Princep 4L conversions.
***For cocklebur, yellow nutsedge, and velvetleaf control on fine-textured soils above
3% organic matter, apply 2.25 Ibs./A of AAtrex Nine-O, or equivalent rate of AAtrex
4L, or the same total amount of AAtrex + Princep, with 1.33-1.67 pts./A of Medal II.
TANK MIXTURE WITH AATREX; OR AATREX + 2,4-D;OR AATREX + 2,4-D +
BANVEL FOR MINIMUM-TILLAGE OR NO-TILLAGE SYSTEMS
In minimum-tillage or no-tillage systems where corn is planted directly into a cover crop,
stale seedbed, established sod, or previous crop residues, Medal II applied in
combination with AAtrex will kill most emerged small annual weeds. Apply Medal II +
AAtrex before, during, or after planting, but before corn emerges, according to the rates
in Table 1.
Where heavy crop residues exist, add 0.8-1.6 pts./A of an appropriately labeled 3.8 Ibs.
a.i./gal. of 2,4-D amine (such as Weedar64, Weedar64A, DMA-4 Herbicide,
Weedone® 638 or Formula 40) to the spray tank last and apply in a minimum of 25
gals, of carrier per acre.
As carriers, nitrogen solutions and complete liquid fertilizers, applied before corn
emergence, enhance burndown of existing weeds, and therefore, are recommended
instead of water. Add X-77 surfactant at 1.0-2.0 qts./100 gals, of diluted spray, or
another appropriate surfactant at its recommended rate, or add crop oil concentrate plus
28% liquid nitrogen (or equivalent). Apply before weeds exceed 3 inches in height. If
alfalfa is present, add Banvel to the spray mixture at 0.33-0.5 pt./A and apply before
alfalfa exceeds 6 inches in height.

r r -34-
For fields with existing sod grasses (e.g., bromegrass, orchardgrass, rye, or timothy),
when existing weeds exceed 3 inches in height or when very dry conditions exist, add
Gramoxone Inteon at the rate of 2.5 pts./A in place of or in addition to 2,4-D, as
indicated above. Do not apply Gramoxone Inteon in suspension-type liquid fertilizer.
Observe all directions for use, precautions, and limitations on the respective product
labels when applying these products in tank mix combination. Use Balance PRO
combinations only on field corn.
TANK MIXTURE WITH MARKSMAN IN CONSERVATION TILLAGE - FIELD AND
SILAGE CORN
In conservation tillage systems where corn is planted directly into a cover crop or
previous crop residue, Medal II + Marksman will kill most emerged small annual weeds.
Apply Medal II + Marksman before, during, or after planting, but before corn emergence
on medium and fine soils with greater than 2.5% organic matter. For fields with existing
vegetation exceeding 3 inches in height or when very dry conditions exist, add
Gramoxone Inteon at its standard rate. Medal II + Marksman may be applied
postemergence to corn less than 3 inches tall and before weedy grasses exceed the 2-
leaf stage.
As carriers, nitrogen solutions and complete liquid fertilizers, applied before corn
emergence, enhance burndown of existing weeds. Do not apply Gramoxone Inteon in
suspension-type liquid fertilizer or use on emerged corn.
Refer to the Marksman label and follow all directions, limitations, precautions, and
information regarding application and use in corn.
TANK MIXTURE WITH BALANCE PRO - FIELD CORN ONLY
Medal II and Balance PRO have a complementary crop response and weed control
profile which allows various tank mix rate combinations to be considered. The addition
of Balance PRO will improve the control of certain problem weeds including Texas
panicum, woolly cupgrass, and wild proso millet. Medal II improves both the duration
and spectrum of annual grass and small seeded broadleaf weed control, in particular
foxtails (yellow foxtail), witchgrass, and yellow nutsedge.
To reduce the risk of an adverse crop response, the Balance PRO label does not allow
applications to coarse textured soils with less than 1.5% organic matter and warns
about applications to all soils with less than 1.5% organic matter or with pH greater than
7.5, as well as applications made to areas in fields with clay knolls, eroded hillsides, and
exposed subsoil. Medal II has no adverse crop response warnings or use restrictions.
Listed below are compensating rate options for combinations of Medal II and Balance
PRO, i.e. higher rates of Medal II are combined with lower rates of Balance PRO, and
visa versa. Select a rate option for Medal II plus Balance PRO by weighing the intensity
of problem weed pressure (population presence and density) and your acceptance for

-35-
risk of an adverse crop response. For example, where Texas panicum, woolly
cupgrass, or wild proso millet are a primary target weed, use a tank mix combination
with a higher Balance PRO rate for the given soil type. Where your tolerance of an
adverse crop response risk is low and/or a more general weed spectrum is targeted
(especially yellow foxtail, witchgrass or yellow nutsedge), use a tank mix combination
with a higher Medal II rate for the given soil type. Where a target weed is listed as
controlled on both product labels, a tank mix combination option including intermediate
rates of both products may be used. Where a target weed is listed as controlled on only
one product label, do not apply at a lower given rate, or unacceptable control may
result. Follow all other directions for use, rate limitations, precautions and restrictions
on both the Medal II and Balance PRO product labels.
Medal II Plus Balance PRO Tank Mix Rate Options When Applied Pre-plant
(Incorporated or Surface Applied) Up to 7 Days Before Planting or Preemergence
in Field Corn
For coarse textured soils, where 1.5 or 1.88 oz./A of Balance PRO is used, 1.0-1.33
pts./A of Medal II may be applied. Do not use Balance PRO on coarse textured soils
with less than 1.5% organic matter.
For medium textured soils, where 1.5 oz./A of Balance PRO is used, rates as low as
1.33 pts./A of Medal II may be applied. Where 1.88 or 2.25 oz./A of Balance PRO is
used, rates as low as 1.0 pts./A of Medal II may be applied. Medal II can be used in
combinations with Balance PRO at rates up to 1.67 pts./A on medium textured soils.
For fine textured soils, where 1.5 oz./A of Balance PRO is used, rates as low as 1.33
pts./A of Medal II may be applied if the soil organic matter is less than 3% - if the soil
organic matter content is 3% or greater, 1.67 pts./A of Medal II should be applied.
Where 1.88 or 2.25 oz./A of Balance PRO is used, rates as low as 1.33 pts./A of Medal
II may be applied. Where 3.0 oz./A or more of Balance PRO are used, rates as low as
1.0 pts./A of Medal II may be applied. Medal II can be used in combinations with
Balance PRO at rates up to 2.0 pts./A on fine textured soils if the soil organic matter
content is 3% or greater.
TANK MIXTURES FOR POSTEMERGENCE SALVAGE WEED CONTROL IN FIELD
CORN ONLY
For postemergence control of weeds in specific types of field corn, the Medal II
combinations listed below may be used. Full season weed control from early preplant,
preplant incorporated, or preemergence treatments can lead to maximum yield potential
under competition-free conditions. However, if control of emerged weeds is needed, a
postemergence program listed below can be applied to provide residual control for the
remainder of the season.
Restrictions: (1) Follow all label directions, instructions, precautions, and limitations
for each product used. (2) Do not use fluid fertilizer with these mixtures or corn injury

f 32 IS
-36-
may occur. (3) For each tank mixture with Medal II, apply only to the specific field corn
type specified on the tank mix product label. (4) In-row weed control may be reduced
because of lack of coverage when applied to corn over 4 inches tall.
Medal II + Liberty Herbicide: Postemergence Use in LibertyLink® Corn or Corn
Warranted by Bayer CropScience as Being Tolerant to Liberty Herbicide
The tank mixture of Medal II + Liberty Herbicide can be applied postemergence to
weeds and corn from seed designated as LibertyLink or corn warranted by Bayer
CropScience as being tolerant to Liberty Herbicide. Liberty provides postemergence
control of a broad spectrum of grass and broadleaf weeds and the Medal II provides
residual control of grasses and certain broadleaf weeds listed in the label Medal II
Applied Alone - Weeds Controlled. Refer to section - Medal II Alone - Preplant
Incorporated or Preemergence and use the minimum rate per soil texture and organic
matter classification for season-long residual control from this tank mix combination with
Liberty. Refer to the Liberty label for the Liberty postemergence application rate
according to weed species and their maximum height at the time of postemergence
application. Where multiple weed species are present, use the highest Liberty rate
recommended to control the species and growth stages present.
Follow all applicable use directions, limitations, precautions, and information regarding
application to corn on the Medal II and Liberty Herbicide labels. Where difficult species
and/or severe weed populations are expected, use the maximum rate where rate
ranges are listed.
Medal II + Liberty ATZ Herbicide: Postemergence Use in LibertyLink Corn or Corn
Warranted by Bayer CropScience as Being Tolerant to Liberty ATZ Herbicide
The tank mixture of Medal II + Liberty ATZ Herbicide can be applied postemergence to
weeds and corn from seed designated as LibertyLink or corn warranted by Bayer
CropScience as being tolerant to Liberty ATZ Herbicide. Liberty ATZ Herbicide provides
postemergence control of a broad spectrum of grass and broadleaf weeds and the
Medal II provides residual control of grasses and certain broadleaf weeds listed in the
label Medal II Applied Alone - Weeds Controlled. Refer to Corn - Medal II Alone -
Preplant Incorporated or Preemergence and use the minimum rate per soil texture
and organic matter classification for season-long residual control from this tank mix
combination with Liberty ATZ Herbicide. Refer to the Liberty ATZ Herbicide label for the
Liberty ATZ Herbicide postemergence application rate according to weed species and
their maximum height at the time of postemergence application. Where multiple weed
species are present, use the highest Liberty ATZ Herbicide rate recommended to
control the species and growth stages present. Do not apply to corn exceeding 12
inches in height.
Follow all applicable use directions, limitations, precautions, and information regarding
application to corn on the Medal II and Liberty ATZ Herbicide labels. Where difficult

(-37-
species and/or severe weed populations are expected, use the maximum rate where
rate ranges are listed.
Medal II + Touchdown or Roundup Ultra for Postemergence Application to Corn
with the Roundup Ready Gene
The tank mixture of Medal II + Touchdown or Roundup Ultra can be applied
postemergence to weeds and to corn designated as containing the Roundup Ready
Gene. Application may be applied postemergence to Roundup Ready corn from
emergence until corn reaches 30 inches tall or the V8 stage (8 leaves with collars),
whichever comes first. This mixture will provide postemergence control of weed
species on the Roundup Ultra label and residual control of weed species on the Medal II
label. Use the minimum Medal II rate postemergence with Roundup Ultra in Roundup
Ready corn as specified in Corn - Medal II Alone - Preplant Incorporated or
Preemergence section of this label according to soil texture and organic matter. Refer
to the Supplemental Labeling of Touchdown or Roundup Ultra for Postemergence
Application to Corn with the Roundup Ready Gene and to the Roundup Ultra
herbicide label and follow appropriate use directions, application procedures,
precautions, and limitations. Apply 24-32 fl. oz./A of Roundup Ultra for control of
labeled broadleaf and grass weeds. Refer to the Roundup Ultra label for directions for
control of problem species.
Follow all applicable use directions, limitations, restrictions, and information regarding
application to corn on the Medal II and Touchdown or Roundup Ultra labels, and on the
Supplemental Labeling of Roundup Ultra for Postemergence Application to Corn
with the Roundup Ready Gene. Where difficult species and/or severe weed
populations are expected, use the maximum rate where rate ranges are listed.
Medal II + Roundup Ultra + AAtrex for Postemergence Application to Corn with
the Roundup Ready Gene
The tank mixture of Medal II + AAtrex + Roundup Ultra can be applied postemergence
to weeds and to corn designated as containing the Roundup Ready Gene. Application
may be applied postemergence to Roundup Ready corn from emergence up to 12
inches in height. This mixture will provide postemergence control of weed species on
the Roundup Ultra label and residual control of weed species on the Medal II + AAtrex
label. Use the minimum Medal II + AAtrex rate postemergence with Roundup Ultra in
Roundup Ready corn as specified in Corn - Medal II Combinations - Tank Mixture
with AAtrex or Princep, or AAtrex + Princep - Preplant Surface, Preplant
Incorporated, or Preemergence section - Table 1 of this label according to soil
texture and organic matter. Refer to the Supplemental Labeling of Roundup Ultra
for Postemergence Application to Corn with the Roundup Ready Gene and to each
product label and follow all appropriate use directions, application procedures,
precautions, and limitations. Apply 24-32 fl. oz./A of Roundup Ultra for control of
labeled broadleaf and grass weeds. Refer to the Roundup Ultra label for directions to
control problem species.

-38-
Follow all applicable use directions, limitations, restrictions, and information regarding
application to corn on the Medal II, AAtrex, and Roundup Ultra labels, and on the
Supplemental Labeling of Roundup Ultra for Postemergence Application to Corn
with the Roundup Ready Gene. Where difficult species and/or severe weed
populations are expected, use the maximum rate where rate ranges are listed.
COTTON - MEDAL II ALONE
Application: Apply Medal II preemergence only in Area 1* at the rate of 0.5-1.0 pts./A
on sandy loams, 0.66-1.33 pts./A on medium soils, or 1.0-1.33 pts./A on fine soils.
Apply Medal II preplant incorporated or preemergence in Area 2** at 1.0 pt./A on sandy
loams, 1.0-1.33 pts./A on medium soils, or 1.33 pts./A on fine soils. Do not use on
sands and loamy sand.
*Area 1 = AR, KS, LA, MS, TN, and Bootheel of MO
**Area 2 = NM, OK, and TX
Preplant Incorporated (NM, OK, and TX Only): Apply to the soil and incorporate into
the top inch of soil immediately before planting, at planting, or after planting, but before
crop or weeds emerge. Use a rolling cultivator or similar implement to uniformly
incorporate not more than 1 inch deep. Use a preplant incorporated application if furrow
irrigation is used or when a period of dry weather after application is expected. Where
furrow irrigation is used, wet the top of the bed for best results. If the crop is to be
planted on beds, apply and incorporate after bed formation. Cotton should be planted
below the zone of incorporation; i.e., at least 1 inch on fine soils and 1.5 inches on
coarse and medium soils. If incorporated prior to planting, use a planter that will result
in a minimum of soil disturbance.
Note: For best control of yellow nutsedge and suppression of seedling johnsongrass,
apply Medal II preplant incorporated at the maximum rate for the soil texture, whether
applied alone or mixed with Caparol 4L.
Preemergence: Apply to the soil surface at planting or after planting, but before weeds
or crop emerge.
Restrictions: To avoid crop injury, (1) Do not apply Medal II on sand or loamy sand
soils, or in areas where water is likely to "pond" over the bed; (2) To avoid concentration
in the seed furrow, do not make broadcast applications of Medal II to cotton planted in
furrows more than 2 inches deep. Band applications maybe made to cotton planted in
furrows deeper than 2 inches, but band width should not exceed the width of the bottom
of the furrow; and (3) Do not apply on Taloka silt loam. (4) Do not use in Games
County, TX.
Restriction: To avoid possible illegal residues, do not graze or feed forage or fodder
from cotton to livestock.

-39-
COTTON - MEDAL II COMBINATIONS
TANK MIXTURE WITH CAPAROL 4L
Medal II tank mixtures with Caparol 4L may be applied in water or fluid fertilizer. When
fluid fertilizer is used as a carrier for Medal II, either alone or in combination with
Caparol 4L, mix only the amount that will be sprayed in one operation. These mixtures
should not be allowed to stand without agitation.
In addition to those weeds controlled by Medal II alone, Medal II + Caparol 4L, applied
preplant incorporated or preemergence, also controls the following weeds: junglerice,
wild oats, annual morningglory, groundcherry, hairy nightshade, lambsquarters, malva,
mustard, prickly sida (teaweed), purslane, ragweed, and shallow-germinating seedlings
of cocklebur and coffeeweed.
Preplant Incorporated or Preemergence: Apply Medal II + Caparol 4L, either
preplant incorporated or preemergence, using the appropriate rate from Table 3. Cotton
should be planted below the zone of incorporation; i.e., at least 1.0 inch on fine soils
and 1.5 inches on coarse and medium soils. If incorporated before planting, use a
planter that will result in a minimum of soil disturbance.
Table 3: Medal II + Caparol 4L - Cotton (NM, OK, TX)
Use Areas
ALL
OK, and Blacklands and
Gulf Coast of TX
Rio Grande
Valley of TX
NM; High Plains, Rolling
Plains, Edwards Plateau of
TX; and Southwest TX
Soil Texture
Sand, loamy sand
Loams
Clays
Loams
Clays
Sandy loam
Loams
Sandy clay loams
Other clay soils
Broadcast Rates Per Acre
Medal II Caparol 4L
DO NOT USE
0.8-1. 33 pts.
1 .33 pts.
0.8-1. 33 pts.
1.33 pts.
0.8-1. Opt.
0.8-1 .33 pts.
1.33 pts.
1 .33 pts.
2.4 pts.
4.8 pts.
3.2pts.
4.8 pts.
1 .6 pts.
2.4 pts.
2.4 pts.
3.2 pts.
Precautions and Restrictions: (1) To avoid concentration in the seed furrow, do not
make broadcast applications of Medal II + Caparol 4L to cotton planted in furrows more
than 2 inches deep. Band applications may be made to cotton planted in furrows
deeper than 2 inches, but band width should not exceed the width of the bottom of the
furrow. To avoid crop injury, (2) Do not apply on sand or loamy sand soils, or in areas
where water is likely to "pond" over the bed; (3) Do not apply in cut areas of newly
leveled fields, or in areas of excess salt; (4) Do not apply to glandless cotton varieties;
and (5) Do not apply on Taloka silt loam. (6) Do not use in Gaines County, TX.

-40-
Restriction: To avoid possible illegal residues, do not graze or feed forage or fodder
from cotton to livestock.
Refer to the Caparol 4L label for further instructions and limitations.
TANK MIXTURE WITH COTORAN DF
Medal II may be applied in tank mixture with Cotoran DF preemergenoe for control of
those weeds controlled by Medal II alone and those as listed on the Cotoran DF label.
This combination will also control spotted spurge, hyssop spurge, nodding spurge, and
prostrate spurge. Apply to the soil surface at planting or after planting, but before
weeds or crop emerge, using the appropriate rates from Table 7.
Mixing Instructions: Incompatibility may occur when tank mixing Medal II and Cotoran
DF. To help overcome this condition, fill the spray tank % full with water or fluid fertilizer
and start agitation, add the Cotoran DF and allow it to become dispersed. Add X-77 at
0.5% volume/volume final spray (4.0 pts./100 gals.), then add the Medal II and finally
the rest of the water or fluid fertilizer. Agitate during mixing and application to maintain
a uniform suspension.
Table 7: Medal II + Cotoran DF - Cotton
Soil Texture
Sand, loamy sand
Sandy loam
Loam, silt loam, silt
Fine soil
Broadcast Rates Per Acre
Medal II (pts.)
Area 1* Area 2**
Cotoran DF***
(Ibs.)
DO NOT USE
0.5-1.0
0.66-1.33
1.0-1.33
0.8-1.0
1.0-1.33
1.33
1.2
1.2-1.9
1.9-2.4
*Area 1 = AR, LA, MS, Bootheel of MO and TN
**Area 2 = Eastern OK, Gulf Coast, Rio Grande Valley, and Eastern TX
***When using Cotoran 4L, use equivalent rates. Multiply Ibs. of Cotoran DF by 1.7 to
get pts. of Cotoran 4L.
Precautions and Restrictions: (1) Do not apply Medal II + Cotoran on sand or loamy
sand soils, or in areas where water is likely to "pond" over the bed, or crop injury may
occur. (2) To avoid concentration in the seed furrow, do not make broadcast
applications of Medal II + Cotoran to cotton planted in furrows more than 2 inches deep.
Band applications may be made to cotton planted in furrows deeper than 2 inches, but
band width should not exceed the width of the bottom of the furrow. (3) The use of
Cotoran following the use of a systemic insecticide at planting may result in crop injury.

-41-
(4) Do not use on Taloka silt loam, or crop injury may occur. (5) Do not use in Gaines
County, TX.
Refer to the Cotoran labels for further instructions, precautions, and limitations.
Restriction: To avoid possible illegal residues, do not feed treated forage or gin trash
to livestock, or graze treated areas.
TANK MIXTURE OF MEDAL II OR MEDAL II + COTORAN WITH GRAMOXONE
INTEON OR ROUNDUP FOR MINIMUM-TILLAGE OR NO-TILLAGE SYSTEMS
In minimum-tillage or no-tillage systems where cotton is planted directly into a cover
crop, stale seedbed, or previous crop residues, the contact herbicides Gramoxone
Inteon or Roundup may be added to a tank mix of either Medal II or Medal II + Cotoran,
When used as directed, the Gramoxone Inteon a portion of the tank mixture controls
most emerged weeds and suppresses many perennial weeds. Roundup combinations
will control emerged annual and perennial weeds when applied as directed on the
Roundup label. The Medal II and Medal II + Cotoran portion of the tank mixture
provides preemergence control of the weeds listed on this label in the Medal II and
Medal II + Cotoran sections, respectively.
Refer to the label of each product used in combination and observe the planting details,
information regarding application, geographical restrictions, and all other precautions
and limitations. Refer to Mixing Instructions under Tank Mixture with Cotoran DF
section.
Application: Apply before, during, or after planting, but before the cotton emerges, at
the rates specified below. Apply Medal II at 0.8-1.0 pt./A on sandy loams, medium-, and
fine-textured soils. Refer to Table 4 for the Cotoran DF rates.
Add Gramoxone Inteon or Roundup at the following broadcast rates:
Gramoxone Inteon: 1.5-2.0, 2.0-2.5, or 2.5-3.0 pts./Ato 1-3, 3-6, or 6-inch tall
weeds, respectively. Apply surfactant at 1.0 or 2.0 pts./100 gals, of spray mixture
with 75% or greater or 50-74% nonionic active ingredient, respectively. This
treatment will not control weeds taller than 6 inches.
Restriction: Do not apply combinations containing Gramoxone Inteon in
suspension-type liquid fertilizers, as the activity of paraquat will be reduced.
Roundup: See the Roundup label for weeds controlled, recommended rates,
and other use directions.
Apply in 20-60 gals, of water or fluid fertilizer per acre with ground equipment.

-42-
Restrictions and Precautions: (1) If heavy rain occurs soon after application, crop injury
may result, especially in poorly drained areas where water stands for several days, or
where the seeding slit has not been properly closed. (2) Refer to the Cotoran labels
and the Tank Mixture with Cotoran DF section of this label for further instructions,
precautions, and limitations. (3) Do not use in Gaines County, TX.
PEANUTS - MEDAL II ALONE
Apply Medal II, either preplan! incorporated, postplant incorporated, or preemergence,
using the appropriate rate specified below. Preplant Incorporated or Preemergence:
Follow instructions for use of Medal II alone under Application Procedures. Postplant
Incorporated: Apply and shallowly incorporate Medal II into the soil after planting, but
before peanut germination. Incorporation depth and incorporating implements must be
kept above the seed, or seed will be damaged.
Apply Medal II alone, preplant incorporated, postplant incorporated, or preemergence,
at a broadcast rate of 1.0-1.33 pts./A in the Southeast* and 0.8-1.33 pts./A in NM, OK,
and TX.
*ln the Southeast, use 1.33-2.0 pts./A and apply preemergence for partial control of
Florida beggarweed.
Restrictions and Precautions: (1) Medal II alone may be applied as directed after any
of the following preplant incorporated herbicides when used according to their label
recommendations: Balan at 3.0-4.0 qts./A; Treflan E.G. at 1.0 pt./A; Sonalan at 1.25-
3.0 pts./A; Pursuit at 0.25 pt./A; or Prowl at 1.0-2.0 pts./A. (2) Do not graze or feed
peanut forage or fodder to livestock for 30 days following application, and (3) Do not
apply within 90 days of harvest, or illegal residues may result.
PEANUTS - MEDAL II COMBINATIONS
TANK MIXTURE WITH BALAN L.C.
Medal II + Balan tank mixture applied preplant incorporated controls those weeds listed
under Medal II Applied Alone and those weeds as listed on the Balan label.
Apply 1.0-1.33 pts./A of Medal II + 3.0-4.0 qts./A of Balan in a minimum of 10 gals, of
spray volume per acre for ground application or in a minimum of 5.0 gals, of spray
volume per acre for aerial application. Follow the recommended procedures for Balan
on the Balan label for soil preparation and incorporation of this tank mix. Apply and
incorporate Medal II + Balan up to 14 days prior to planting.
Note: Follow all restrictions and precautions on the Balan label.

-43-
TANK MIXTURE OR SEQUENTIALLY WITH PURSUIT
The tank mixture or sequential treatment of Medal II and Pursuit controls all weeds
controlled by Medal II alone and by Pursuit alone. Refer to the Medal II Applied Alone
section for weeds controlled by Medal II and to the Pursuit label for weeds controlled by
Pursuit.
Refer to the respective labels for application methods, timing, rates, restrictions, and
precautions; and use in accordance with either product. Medal II will not control
emerged weeds.
TANK MIXTURE WITH SONALAN
The tank mixture controls all weeds controlled by Medal II alone and by Sonalan alone.
Refer to the Medal II Applied Alone section for weeds controlled by Medal II and to the
Sonalan label for weeds controlled by Sonalan.
Apply Medal II + Sonalan preplant incorporated, using the appropriate rate from Table 5.
Follow recommended soil preparation procedures for Sonalan.
Table 5: Medal II + Sonalan - Peanuts
Soil Texture
COARSE
MEDIUM
FINE
Broadcast Rates Per Acre
Southeast
Medal II
1.0-1.33pts.
1.0-1.33pts.
1.0-1. 33 pts.
Sonalan
1.25-2.0 pts.
1.75-2.5 pts.
2.25-3.0 pts.
NM, OK, TX
Medal II
0.8-1. 33 pts.
0.8-1 .33 pts.
0.8-1. 33 pts.
Sonalan
1.25-2.0 pts.
1.75-2.5 pts.
2.25-3.0 pts.
Note: Follow all use directions, limitations, precautions, and information regarding
application to peanuts on the Medal II and Sonalan labels.
TANK MIXTURE WITH PROWL
Medal II + Prowl applied preplant incorporated controls all weeds controlled by Medal II
alone plus Texas panicum, field sandbur, johnsongrass from seed, lambsquarters,
kochia, annual spurge, and other species on the Prowl label. Apply Medal II + Prowl by
ground or by aerial equipment within 14 days before planting. Incorporate into the top
1-2 inches of soil before planting and within 7 days of application, using a finishing disk
or similar implement capable of providing uniform incorporation. If peanuts will be
planted on beds, apply and incorporate after bed formation. Refer to the Incorporation
instructions of the respective labels for additional directions.
Apply Medal II + Prowl preplant incorporated, using the appropriate rates from Table 6.

-44-
Table 6: Medal II + Prowl - Peanuts
Soil Texture
Sand, loamy sand
Sandy loam
Fine soil
Broadcast Rates Per Acre
NM, OK, TX
Medal II + Prowl
0.8 + 1.0-1.5pts.
0.8-1.0 + 1.0-1. 5 pts.
1.33 + 1.0-1.5pts.
Other Peanut
Growing States
Medal II + Prowl
1.0-1 .33 +1.5-2.0 pts.
1.0-1.33 + 1.5-2.0 pts.
1.33 + 1.5-2.0 pts.
Note: Follow all use directions, limitations, restrictions, and information regarding
application to peanuts on the Medal II and Prowl labels.
SEQUENTIALLY WITH STORM
Apply Medal II according to the directions for Medal II Alone and follow with a
postemergence treatment of Storm as specified on its label for the control of weeds
listed on the Medal II label and on the Storm label. Refer to the Medal II - Peanuts -
Alone section and to the Storm label and follow all directions, limitations, and
restrictions for each product.
MULTIPLE APPLICATIONS
Where weed pressure is heavy or where species difficult to control are expected, Medal
II is most effective when used as follows:
Southeast Only (AL, FL, GA, NC, SC, VA)
Preplant Incorporated: Apply Medal II preplant incorporated as directed under
Peanuts - Medal II Alone or apply Medal II + Balan preplant incorporated as directed
previously in this section. Refer to the respective section for weeds controlled.
OR
Preemergence to before "ground cracking": Apply Medal II any time from
preemergence to before "ground cracking" at 1.0-2.0 pts./A for extended control of
weeds not yet emerged. Do not use Medal II after peanut emergence. If peanuts
have emerged, use Dual MAGNUM® according to its label: Peanuts - Combinations
- Multiple Applications.
Follow the PPI or PRE application by:
Lay-by: Do not use Medal II. Apply Dual MAGNUM at lay-by as directed under the
Peanuts - Alone section of the Dual MAGNUM label.

r
Restrictions: (1) Do not apply more than the equivalent of 2.67 Ibs. of active ingredient
of Medal II per acre during any one year, or illegal residues may result. If Dual
MAGNUM is used as a sequential treatment, the Ibs. of active ingredient (1.0 pt. =
0.95 Ib.) plus the Ibs. of active ingredient of Medal II should not exceed 2.67 Ibs. Do
not use Medal II, or Dual IIG MAGNUM after peanuts have emerged. (2) Do not
graze or feed peanut forage or fodder to livestock for 30 days following application, and
(3) Do not apply within 90 days of harvest, or illegal residues may result.
Southwest Only (NM, OK, TX)
1st Application: Apply Medal II preplant incorporated or preemergence to before
"ground cracking" as directed under Peanuts - Medal II Alone or apply Medal II +
Balan preplant incorporated as directed previously in this section. Do not use Medal II
after peanut emergence. If peanuts have emerged, use Dual MAGNUM according to
its label.
2nd Application: Do not use Medal II. Apply Dual MAGNUM at lay-by as directed
under the Peanuts - Alone section of the Dual MAGNUM label. Use only when late
germinating weeds are expected to be a problem. Refer to the product Applied Alone
section for a list of weeds controlled.
Restrictions: (1) Do not apply more than the equivalent of 2.67 Ibs. of active ingredient
of Medal II per acre during any one year, or illegal residues may result. If Dual
MAGNUM is used as a sequential treatment, the Ibs. of active ingredient (1.0 pt. =
0.95 Ib.) plus the Ibs. of active ingredient of Medal II should not exceed 2.67 Ibs. Do
not use Medal II, or Dual IIG MAGNUM after peanuts have emerged. (2) Do not
graze or feed peanut forage or fodder to livestock for 30 days following application, and
(3) Do not apply within 90 days of harvest, or illegal residues may result.
POD CROPS - MEDAL II ALONE
Pod crops, including garbanzo, great northern beans, kidney beans, lima beans, mung
beans, navy beans, peas (English*; southern peas, such as blackeye, pinkeye, crowder,
etc.), pinto beans, snap beans (green, wax, string), and lupines (sweet, white, white
sweet, and grain).
Fall Application:
1. Apply after September 30 in ND, SD, MN, Wl, and north of Route 30 in IA.
2. Apply after October 15 north of Route 91 in NE and south of Route 30 in IA.
3. Apply after October 31 north of Route 136 in IL.
In all locations, apply to crop stubble after harvest when the sustained soil temperature
at a 4-inch depth is less than 55°F and falling. In minimum-till or no-tillage systems on
soils having greater than 2.5% organic matter, use 1.67-2.0 pts./A on medium-textured
and 2.0 pts./A on fine-textured soils. Restriction: Do not apply to frozen ground. A

c-46-
tillage operation may precede the application. A fall and/or a spring tillage may follow
application, but do not exceed an incorporation depth greater than 2-3 inches. Minimize
furrow and ridge formation in the tillage operations.
Restriction: If a spring application is made, the total rate of the fall plus spring
applications must not exceed the maximum total rate for pod crops, or illegal residues
may result.
Spring Application:
Apply Medal II, either preplant incorporated or preemergence, using the appropriate rate
specified below. Preplant Incorporated or Preemergence: Follow instructions for use
of Medal II alone under Application Procedures. On coarse so/'/swith less than 3%
organic matter, apply 1.0-1.33 pts./A of Medal II or 1.33 pts./A if organic matter is 3% or
greater. On medium soils, apply 1.33-1.67 pts./A of Medal II. On fine soils, apply 1.33-
1.67 pts./A of Medal II if organic matter content is less than 3%, or 1.67-2.0 pts./A if
organic matter content is 3% or greater.
*On English peas, use only preemergence applications. Do not use on English peas in
northeastern U.S., or injury may occur.
Restrictions: To avoid possible illegal residues, (1) Do not cut for hay within 120 days
following a Medal II application, (2) Do not use for forage within 60 days following a
Medal II application, and (3) Do not apply more than 2.0 pts./A of Medal II during any
one crop year.
POD CROPS - MEDAL II COMBINATIONS
Restriction: When applying Medal II in combination on pod crops, do not cut for hay
within 120 days following application, or illegal residues may result.
TANK MIXTURE AND SEQUENTIAL APPLICATIONS WITH EPTAM - BEANS
(GREEN OR DRY)
This mixture controls all weeds controlled by Medal II alone and by Eptam alone. Refer
to the Medal II Applied Alone section of this label for weeds controlled by Medal II
alone and to the Eptam label for weeds controlled by Eptam.
Preplant Incorporated: Follow instructions for use of Medal II alone under
Application Procedures.
Sequential: Apply Eptam alone preplant incorporated, as specified on that label.
Follow with a preemergence application of Medal II, at rates specified for Medal II alone,
during planting (behind the planter) or after planting, but before the weeds or crop
emerge.

c-47-
Refer to the Product Information section of this label and to the Eptam label for
weather, cultural practices, and all other precautions and limitations that affect
performance of these products.
Apply 2.5-4.5 pts./A of Eptam 7E* with Medal II as specified. On coarse soils, apply
0.8 pt./A of Medal II if organic matter content is less than 3%, or 1.0 pt./A if organic
matter content is 3% or greater. On medium soils, apply 1.0 pt./A of Medal II if organic
matter content is less than 3%, or 1.33 pts./A if organic matter content is 3% or greater.
On fine soils, apply 1.33 pts./A of Medal II if organic matter is less than 3%, or 1.33-
1.67 pts./A if organic matter is 3% or greater.
*Refer to the Eptam label for rate limitations depending on geographical area, and for
species and varietal restrictions.
Restriction: Do not exceed 3.5 pts./A of Eptam 7E on small white beans or green beans
grown on coarse-textured soils.
TANK MIXTURE WITH TREFLAN - BEANS (DRY- KIDNEY, NAVY, PINTO, ETC.;
LIMA; AND SNAP)
Medal II + Treflan tank mix applied preplant incorporated controls those weeds listed
under Medal II Applied Alone and those weeds listed for Treflan alone on the Treflan
label. Medal II + Treflan may be applied by ground or by aerial equipment and
incorporated up to 14 days prior to planting. Follow the recommended procedures on
this label and on the respective Treflan label using equipment that provides uniform 2-
inch incorporation.
Apply Medal II + Treflan tank mix using the appropriate Medal II rate specified for Medal
II alone, and the Treflan rate from the Dry Beans, and the Lima and Snap Beans
sections of the respective Treflan label. Choose the product rate for the specific soil
texture/organic matter classification and weed species expected.
Note: Follow all restrictions and precautions on the respective Treflan label and in the
Pod Crops - Medal II Alone section of this label.
POTATOES - MEDAL II ALONE
Apply Medal II, either incorporated or preemergence, according to directions specified
below for control of weeds listed under the Product Information section. Within a rate
range, use the lower rate on soils relatively coarse-textured or low in organic matter;
use the higher rate on soils relatively fine-textured or high in organic matter.
Effectiveness will be reduced if later cultural practices expose untreated soil. For
application by center pivot irrigation, see Center Pivot Irrigation Application section.
Incorporated: Apply Medal II at 1.0-2.0 pts./A to the soil and incorporate into the top 3
inches before planting, using a finishing disk, harrow, rolling cultivator, or similar

-48-
implement. Planting and later cultural practices should not bring untreated soil to the
surface. Postplant incorporated application may be made any time after planting to
drag-off, but before potato emergence. Use an implement that evenly distributes Medal
II in the top 2 inches of soil. Do not damage potato seed pieces or sprouts with
incorporation equipment.
Preemergence: Apply Medal II at 1.0-2.0 pts./A, either after planting as a
preemergence, delayed preemergence, after drag-off or hilling treatment, but before
weeds emerge. Up to 2.5 pts./A of Medal II alone may be used where soil organic
matter is between 6% and 20%.
Restrictions: (1) Do not use on muck or peat soils. If cool, wet soil conditions occur
after application, Medal II may delay maturity and/or reduce yield of Superior and other
early maturing potato varieties. To avoid crop injury, (2) Do not use on sweet potatoes
or yams; (3) Do not apply both as a preemergence and an incorporated treatment; and
(4) Do not use in Kern County, CA.
Restriction: Potatoes treated with Medal II must not be harvested within 60 days after
the at-planting to drag-off application, or illegal residues may result.
POTATOES - MEDAL II COMBINATIONS
TANK MIXTURE WITH SENCOR OR LEXONE
In addition to those weeds controlled by Medal II alone, Medal II applied in tank mix
combination with, or sequentially with, any of the registered Sencor or Lexone
formulations, also controls the following broadleaf weeds: cocklebur*, hairy
nightshade*, hemp sesbania, jimsonweed*, lambsquarters, prickly sida, ragweed,
smartweed, velvetleaf, Venice mallow, and wild mustard.
*Partially controlled.
Medal II at 1.0-2.0 pts./A plus the labeled Sencor/Lexone use rate may be used
preemergence. Apply 1.0-1.33 pts./A of Medal II on coarse soils and 1.33-2.0 pts./A on
other soil textures. Within this rate range, use the lower rate on soils relatively coarse-
textured or low in organic matter; use the higher rate on soils relatively fine-textured or
high in organic matter. Effectiveness will be reduced if later cultural practices expose
untreated soil. Medal II will not control emerged weeds.
Refer to the Sencor or Lexone labels for precautionary statements, restrictions,
application information, center pivot irrigation application, weeds controlled, and varietal
limitations.
Restrictions: (1) Do not use Medal II + Sencor or Lexone on potatoes in Kern County,
CA. (2) Do not apply to sweet potatoes or yams. (3) Do not use this tank mixture on
muck or peat soils.

Restriction: Potatoes treated with Medal II jn tank mixture with Sencor or Lexone
cannot be harvested within 60 days after application, or illegal residues may result.
MEDAL II + LOROX TANK MIXTURE (EAST OF ROCKY MOUNTAINS)
Medal II may be applied in a tank mix combination with any of the registered Lorox
formulations as a preemergence broadcast application to potatoes. Apply to the soil
surface after planting and before emergence of the crop or after final drag-off according
to the rates specified in Table 7.
Table 7: Medal II + Lorox - Potatoes (East of Rocky Mountains)
Soil Texture
COARSE
Sandy loam
MEDIUM
Loam, silt loam,
silt
Broadcast Rates Per Acre
1% to Less Than 3%
Organic Matter
Medal II
1.0pt.
1.33pts.
Lorox*
1.0-1 .5 IDS.
1. 5-2.0 Ibs.
3-5%
Organic Matter
Medal II
1.33pts.
1. 67-2.0 pts.
Lorox*
1.5-2.0 Ibs.
2.0-2.5 Ibs.
*When using Lorox L or Lorox DF, use equivalent rates. One pt. of Lorox L equals 1.0
Ib. of Lorox DF.
Restrictions: To avoid crop injury, (1) Do not use on sands or loamy sands, and (2) Do
not incorporate or spray over the top of emerged potatoes.
Refer to the Product Information section of this label and to the Lorox label for
precautionary statements, restrictions, application information, and weeds controlled.
TANK MIXTURE WITH PROWL 4E
In addition to the weeds controlled by Medal II alone, this tank mixture with Prowl 4E
controls such problem species as kochia, lambsquarters, purslane, annual spurge,
stinging nettle, and others specified on the Prowl 4E Alone label. Apply Medal II +
Prowl 4E preemergence or preemergence incorporated, according to the specific
directions on the Prowl 4E label, using the rates in Table 8.

r-50-
Table 8: Medal II + Prowl 4E -Potatoes
Soil Texture
COARSE
MEDIUM
FINE
Broadcast Rates Per Acre
Less Than 3%
Organic Matter
Medal II + Prowl 4E*
1.0-1. 33 pts. + 1.0-1.5pts.
1.33pts. + 1.5-2.0 pts.
1 .33-1 .67 pts. + 2.0-3.0 pts.
More Than 3%
Organic Matter
Medal II + Prowl 4E*
1.0-1. 33 pts. + 1.0-1 .5 pts.
1.33-1. 67 pts. +2.0-3.0 pts.
1.67-2.0 pts. + 3.0 pts.
*When using other formulations of Prowl, use equivalent rates of active ingredient.
Refer to the Medal II and Prowl 4E labels and observe all directions, timings, limitations,
precautions, and restrictions concerning the use of these products on potatoes and
follow the most restrictive.
TANK MIXTURE WITH PROWL 4E + EPTAM
In addition to the weeds controlled by Medal II alone, this tank mixture will control those
species on the Prowl 4E and Eptam labels. Refer to the Medal II + Prowl 4E labels for
rates of those products and add Eptam 7E at 3.5-7.0 pts./A, depending on geographical
area. Refer to the respective Medal II, Prowl 4E, and Eptam labels and observe all
directions, limitations, precautions, and restrictions concerning the use of these
products on potatoes and follow the most restrictive.
SAFFLOWERS - MEDAL II ALONE
Preplant Incorporated or Preemergence: Follow instructions for use of Medal II alone
under Application Procedures.
On coarse soils, apply 1.0-1.33 pts./A of Medal II if organic matter content is less than
3%, or 1.33 pts./A if organic matter is 3% or greater. On medium soils, apply 1.33-1.67
pts./A of Medal II. On fine soils, apply 1.33-1.67 pts./A of Medal II if organic matter
content is less than 3%, or 1.67-2.0 pts./A if organic matter content is 3% or greater.
GRAIN OR FORAGE SORGHUM (SEED TREATED WITH CONCEP®) - MEDAL II
ALONE
Apply Medal II, either preplant surface, preplant incorporated, or preemergence, using
the appropriate rate specified below. Apply Medal II alone only when the sorghum seed
has been properly treated by the seed company with Concep.
Preplant Surface-Applied: Refer to instructions for use of Medal II under Application
Procedures. For minimum-tillage or no-tillage systems only, Medal II may be applied
up to 45 days before planting in CO, IA, IL, KS, MO, NE, and SD. Use only split

(" 53J7S
-51-
applications for treatments made 30-45 days prior to planting, with 2/3 of the broadcast
rate applied initially and the remaining 1/3 at planting. Apply 1.5 pts./A of Medal II on
medium soils or 1.67 pts./A on fine soils. Treatments less than 30 days prior to planting
may be made either as a split or single application. Apply 1.33 pts./A of Medal II on
coarse soils not more than 2 weeks prior to planting. Under dry conditions, irrigation
after application is recommended to move Medal II into the soil.
Preplant Incorporated or Preemergence: Refer to instructions for use of Medal II
under Application Procedures. Broadcast 1.0-1.33 pts./A of Medal II on coarse so/7s,
1.33-1.5 pts./A on medium soils, or 1.33-1.67 pts./A on fine soils.
Restrictions and Precautions: (1) If sorghum seed is not properly treated with Concep,
Medal II will severely injure the crop. (2) Under high soil moisture conditions prior to
sorghum emergence, injury may occur following the use of Medal II. The crop will
normally outgrow this effect (3) Do not use Medal II on sorghum grown under dry
mulch tillage, or injury may occur. (4) Except for the split preplant surface treatment, do
not make more than one application per year, or illegal residues may result.
GRAIN OR FORAGE SORGHUM (SEED TREATED WITH CONCEP) - MEDAL II
COMBINATIONS
Medal II tank mixtures with AAtrex may be applied in water or fluid fertilizer. Apply
Medal II in tank mixtures only when the sorghum seed has been properly treated by the
seed company with Concep.
IMPORTANT: FOR TANK MIXTURES WITH AATREX (OR OTHER BRANDS OF
ATRAZINE) - If applying Medal II in tank mixture with AAtrex, all the restrictions
and rate limitations on the AAtrex label must be followed if more
restrictive/protective than those on this label. In addition, if AAtrex is/must be
applied at rates lower than those recommended on this label, broadleaf weed
control may be affected. Refer to the AAtrex label for weeds controlled at the
reduced rates.
Restrictions and Precautions: (1) Applications of Medal II + AAtrex on highly alkaline
soils or on eroded areas where calcareous subsoils are exposed may cause sorghum
injury. (2) If sorghum seed is not properly treated with Concep, Medal II + AAtrex may
severely injure the crop. (3) Under high soil moisture conditions prior to sorghum
emergence, injury may occur following the use of Medal II + AAtrex. The crop will
normally outgrow this effect. (4) Do not use Medal II + AAtrex on sorghum grown under
dry mulch tillage, or injury may occur. (5) Except for the split preplant surface
treatment, do not make more than one application per year, or illegal residues may
result.

r-52-
TANK MIXTURE WITH AATREX
In addition to the weeds controlled by Medal II alone, Medal II + AAtrex also controls the
following broadleaf weeds when applied either preplant surface, preplant incorporated,
or preemergence: cocklebur, common purslane, hairy nightshade, lambsquarters,
morningglory, ragweed, smartweed, and velvetleaf.
Preplant Surface-Applied: Refer to instructions for use of Medal II under Application
Procedures. For minimum-tillage or no-tillage systems only, Medal II + AAtrex may be
applied up to 45 days prior to planting in IA, IL, eastern KS, MO, NE, and SD. Use only
split applications for treatments made 30-45 days prior to planting, with 2/3 of the
broadcast rate applied initially and the remaining 1/3 at planting. Apply 1.5 pts./A of
Medal II + 1.7-2.0 Ibs./A of AAtrex Nine-O* on medium soils with 1.5% organic matter or
greater. Apply 1.5 pts./A of Medal II + 1.7-2.0 Ibs./A of AAtrex Nine-O on fine soils with
less than 1.5% organic matter, or apply 1.67 pts./A of Medal II + 2.0-2.2 Ibs./A of
AAtrex Nine-O on fine soils with 1.5% organic matter or greater. Treatments less than
30 days prior to planting may be made either as a split or single application. Under dry
conditions, irrigation after application is recommended to move Medal II + AAtrex into
the soil.
Restrictions: To avoid crop injury, (1) Do not use on coarse soils, and (2) Do not use on
medium soils with less than 1.5% organic matter.
Preplant Incorporated or Preemergence: Refer to instructions for use of Medal II
under Application Procedures. On medium soils with 1.5% organic matter or greater,
apply 1.0 pt./A of Medal II + 1.3 Ibs./A of AAtrex Nine-O*. On fine soils with less than
1.5% organic matter, apply 1.0 pt./A of Medal 11 + 1.3 Ibs./A of AAtrex Nine-O; on fine
soils with 1.5% organic matter or greater, apply 1.2-1.33 pts./A of Medal 11 + 1.6-1.8
Ibs./A of AAtrex Nine-O.
*When using AAtrex 4L, use equivalent rates. One Ib. of AAtrex Nine-O equals 1.8 pts.
of AAtrex 4L.
Restrictions: To avoid crop injury, (1) Do not use on coarse soils; (2) Do not use on
medium soils with less than 1.5% organic matter; (3) Do not use in NM, OK, or TX,
except in northeast OK and the TX Gulf Coast and Blacklands areas; and (4) Do not
apply preplant incorporated in AZ or the Imperial Valley of CA.
TANK MIXTURE OF MEDAL II OR MEDAL II + AATREX, WITH GRAMOXONE
INTEON, LANDMASTER BW, OR ROUNDUP FOR MINIMUM-TILLAGE OR NO-
TILLAGE SYSTEMS
In minimum-tillage or no-tillage systems where sorghum (seed treated with Concep) is
planted directly into a cover crop, stale seedbed, established sod, or previous crop
residues, the contact herbicides Gramoxone Inteon, Landmaster BW, or Roundup may

( S5/7S
-53-
be tank mixed with Medal II or Medal II + AAtrex. See Comment No. 7 following Chart
1. The Medal II or Medal II + AAtrex portion of the tank mixture provides preemergence
control of the weeds listed on this label under the respective sections.
Refer to the label of each product used in combination and observe the planting details,
restrictions, and all other precautions and limitations.
Application: Apply before, during, or after planting, but before sorghum emerges, at
the appropriate rates listed under Grain or Forage Sorghum - Medal II Alone or -
Medal II Combinations - Medal II + AAtrex, respectively. Add Gramoxone Inteon,
Landmaster BW, or Roundup at the following broadcast rates:
Gramoxone Inteon: 1.5-2.0, 2.0-2.5, or 2.5-3.0 pts./A to 1-3, 3-6, or 6-inch tall weeds,
respectively. Apply surfactant at 1.0 or 2.0 pts./100 gals, of spray mixture with 75% or
greater or 50-74% nonionic active ingredient, respectively. This treatment will not
control weeds taller than 6 inches.
Landmaster BW: 27-54 oz./A depending on weed species and size. See the
Landmaster BW label for weeds controlled, recommended rates for specific weeds, and
other information concerning use.
Roundup: See the Roundup or Roundup RT label for weeds controlled, recommended
rates, and other use directions.
Apply in a minimum of 20 gals, of water per acre with conventional spray equipment.
SOYBEANS - MEDAL II ALONE
Apply Medal II, either preplant surface-applied, preplant incorporated, or preemergence,
or as a postemergence treatment using the appropriate rate specified below.
Preplant Surface-Applied, Preplant Incorporated, or Preemergence: Follow
instructions for use of Medal II alone under Application Procedures.
Preplant Surface-Applied
Fall Application:
1. Apply after September 30 in ND, SD, MN, Wl, and north of Route 30 in IA.
2. Apply after October 15 north of Route 91 in NE and south of Route 30 in IA.
3. Apply after October 31 north of Route 136 in IL.
In all locations, apply to crop stubble after harvest when the sustained soil temperature
at a 4-inch depth is less than 55°F and falling. In minimum-till or no-tillage systems on
soils having greater than 2.5% organic matter, use 1.67-2.0 pts./A on medium-textured
and 2.0 pts./A on fine-textured soils. Restriction: Do not apply to frozen ground. A
tillage operation may precede the application. A fall and/or a spring tillage may follow

c ay is-54-
application, but do not exceed an incorporation depth greater than 2-3 inches. Minimize
furrow and ridge formation in the tillage operations.
Restriction: If a spring application is made, the total rate of the fall plus spring
applications must not exceed the maximum total rate on soybeans, or illegal residues
may result.
Use on medium and fine soils with minimum-tillage or no-tillage systems in CO, CT, DE,
IA, IL, IN, KS, KY, MA, MD, ME, Ml, MN, MO, MT, ND, NE, NH, NY, OH, PA, Rl, SD,
TN, VA, VT, Wl, WV, and WY. Apply 2/3 the recommended rate of Medal II (1.67 pts./A
on medium soils and 2.0 pts./A on fine soils) as a split treatment 30-45 days prior to
planting and the remainder at planting. Applications made less than 30 days before
planting may be as either a split or single treatment. Apply 1.33 pts./A on coarse soils
not more than 2 weeks before planting.
Preplant Incorporated or Preemergence: On coarse soils, apply 1.0-1.33 pts./A of
Medal II if organic matter content is less than 3%, or 1.33 pts./A if organic matter
content is 3% or greater. On medium soils, apply 1.33-1.67 pts./A of Medal II. On fine
soils, apply 1.33-1.67 pts./A of Medal II if organic matter content is less than 3%, or
1.67-2.0 pts./A if organic matter content is 3% or greater.
MEDAL II PROGRAMS FOR PLANNED TWO-PASS WEED CONTROL SYSTEMS IN
ROUNDUP READY AND GLYPHOSATE TOLERANT SOYBEANS
Medal II may be applied preplant incorporated or preemergence in Roundup Ready or
glyphosate tolerant soybeans at rates down to1.0 pts./A on all soils when followed by a
planned postemergence application of an approved glyphosate based product-
examples include Touchdown and Roundup UltraMax. Follow all other directions for
use, precautions and restrictions listed for Medal II on this label. The glyphosate
product must be registered for postemergence applications in Roundup Ready or
glyphosate tolerant soybeans and be applied according to the weed and crop timings,
methods, precautions and restrictions listed on the glyphosate containing product label.
When used in this way, Medal II will provide reduced competition of the weeds listed as
controlled in the Product Information section of this label for a period of 30 or more
days, thus improving the timing flexibility and effectiveness of the glyphosate based
product application.
Restriction: On soybeans, Medal II may be used up to 2.5 pts./A as a preplant
surface-applied, preplant incorporated, or preemergence treatment on soils having an
organic matter content between 6% and 20%. The total Medal II rate applied to
soybeans during any one crop must not exceed 2.5 pts./A.

( £7 7S
-55-
POSTEMERGENCE USE ON SOYBEANS - MEDAL II ALONE
Postemergence: Apply 1.0-1.33 pts./A as a postemergence treatment to soybeans.
This treatment will control only weeds that have not emerged. Apply this treatment to
soybeans from emergence up through the third trifoliate leaf stage. A postemergence
application of Medal II may not be applied if a preplant surface, preplant incorporated, or
preemergence application of S-metolachlor products such as Medal or Medal II had
already been applied.
Restrictions: To avoid possible illegal residues when Medal II is applied
postemergence to soybeans: (1) Do not apply more than 1.33 pts./A postemergence.
(2) Make postemergence application at least 90 days before harvest. (3) Do not graze
or feed treated forage or hay from soybeans to livestock following a postemergence
application of Medal II.
SOYBEANS - MEDAL II COMBINATIONS
Water or fluid fertilizer may be used as carrier for Medal II in combination with Sencor,
Lexone, Lorox, Lorox Plus, Gemini, Canopy, Preview, Pursuit, Scepter, Sonalan, or
Command.
Restriction: For all of the following combinations, Medal II may be used up to
2.33 pts./A on soils having an organic matter content between 6% and 20%. The total
Medal II rate applied to soybeans during any one crop year must not exceed 2.5 pts./A.
TANK MIXTURE WITH SENCOR OR LEXONE
In addition to those weeds controlled by Medal II alone, Medal II + Sencor or Lexone,
when applied as directed, also controls the following broadleaf weeds: cocklebur*, hairy
nightshade, hemp sesbania, jimsonweed*, lambsquarters, prickly sida, ragweed,
smartweed, velvetleaf, Venice mallow, and wild mustard.
*Partially controlled.
Apply Medal II and Sencor or Lexone preplant incorporated or preemergence, using the
appropriate rates from Table 9. Preplant Incorporated or Preemergence: Follow
instructions for use of Medal II alone under Application Procedures.
Sequential: Apply Medal II alone Preplant Incorporated, as specified in Table 9 for
this tank mixture. Follow with a preemergence application of Sencor or Lexone during
planting (behind the planter) or after planting, but before weeds or soybeans emerge.
Refer to the Sencor or Lexone labels for planting details and soybean variety
restrictions.

•gff75
-56-
Table 9: Medal It + Sencor or Lexone - Soybeans
Soil Texture**
COARSE
Loamy sand
(over 2%
organic matter),
sandy loam
MEDIUM
FINE
Mississippi
Delta only
Silty clay, clay
Muck or Peat
(soils with more
than 20%
organic matter)
Broadcast Rates Per Acre
0.5% to Less Than 3%
Organic Matter
Medal II +
+
0.8-1 .Opt.
1.0-1.33pts. +
1.33pts. +
+.
1 .33 pts.
Sencor/
Lexone DF*
0.33 Ib.
0.5 Ib.
0.67 Ib.
1.0 Ib.
3% Organic Matter
or Greater
Medal II +
+
1 .0 pt.
1 .33 pts. +
1.33-1 .67 pts. +
+
1 .33-1 .67 pts.
Sencor/
Lexone DF*
0.5 Ib.
0.67 Ib.***
0.67 Ib.
1.0 Ib.
DO NOT USE
*When using Sencor 4 or Lexone 4L, multiply Ibs. of DF by 1.5 to get pts./A.
**On all sand and on loamy sand with less than 2% organic matter, do not use this tank
mixture preemergence, or the sequential treatment. Do not use the tank mixture
preplant incorporated on any sand, loamy sand, or sandy loam, or crop injury may
occur.
***Use 0.5 Ib./A if applied preplant incorporated.
Precautions: (1) Do not use the tank mix or sequential application on soil with less than
0.5% organic matter or on alkaline soil with a pH over 7.4, or crop injury may occur. (2)
If heavy rain occurs soon after application, crop injury may result, especially in poorly
drained areas where water stands for several days.
TANK MIXTURE WITH LOROX
In addition to those weeds controlled by Medal II alone, Medal II + Lorox, applied
preemergence, also controls the following broadleaf weeds: cocklebur*, jimsonweed*,
lambsquarters, morningglory*, prickly sida, ragweed, smartweed, velvetleaf*, Venice
mallow, and wild mustard.
Tartially controlled.

-57-
Preemergence: Apply during planting (behind planter) or after planting, but before
weeds or soybeans emerge. Refer to the Lorox label for planting details. Apply the
appropriate rates from Table 10.
Restriction: Do not use on soil with less than 0.5% organic matter, or crop injury may
occur.
Table 10: Medal II + Lorox - Soybeans
Soil Texture*
COARSE**
MEDIUM
FINE
Muck or Peat
(soils with more
than 20%
organic matter)
Broadcast Rates Per Acre
0.5
Medal II
0.8 pt.
1.0pt.
1 .33 pts
% to Less Than 3%
Organic Matter
+ Lorox DF***
+ 1.0 Ib.
+ 1.0-1 .5 Ibs.
+ 2.0 Ibs.
3% Organic Matter
or Greater
Medal II + Lorox DF***
1.0pt. + 1.0-1 .5 Ibs.
1.33 pts. + 1.5-2.0 Ibs.
1.33-1 .67 pts. + 2.5-3.0 Ibs.
DO NOT USE
*Do not use on sand, gravelly soils, or exposed subsoils.
**Do not use on loamy sand, except in the northeastern U.S. on loamy sand with over
1% organic matter.
***When using Lorox L or Lorox DF, use equivalent rates. One pt. of Lorox L equals 1.0
Ib. of Lorox DF.
TANK MIXTURE WITH TREFLAN
Medal II + Treflan tank mix applied preplant incorporated controls those weeds listed
under Medal II Applied Alone and those weeds listed for Treflan Alone on the Treflan
label. Medal II + Treflan may be applied by ground or aerial equipment and
incorporated up to 14 days before planting. Follow the recommended procedures on
the Treflan and Medal II labels, using equipment that provides uniform 2-inch
incorporation.
Apply Medal II + Treflan tank mix using the appropriate rate from the Soybeans -
Medal II Alone section of this label and the Treflan Alone section of the Treflan label for
the specific soil texture/organic matter classification and weed species expected.
To control DNA-resistant goosegrass* and other species on the respective labels where
the soil organic matter is 3% or less, apply the rate in Table 11.

-58-
Table 11: Medal II + Treflan - Organic Matter Content Less Than 3%
Soil Texture
COARSE*
MEDIUM
FINE
Broadcast Rates Per Acre
Medal II
Organic Matter
Less Than 3%
0.8-1 .Opt.
1 .0 pt.
1.33pts.
Treflan E.G.**
Organic Matter
Less Than 2%
1.0pt.
1 .5 pts.
2.0 pts.
2-3%
1.5 pts.
1.5 pts.
2.0 pts.
*Where a range of rates is given for Medal II, use the minimum rate where DNA-
resistant goosegrass is the predominant species.
**When Treflan MTF or Treflan 5 is used, use comparable rates. Multiply pts. of
Treflan E.G. by 1 for Treflan MTF and by 0.8 for Treflan 5.
Note: Follow all restrictions and precautions on the respective Treflan label and in the
Soybeans - Medal II Alone section of this label.
TANK MIXTURE WITH SCEPTER
This tank mixture controls all weeds controlled by Medal II alone and by Scepter alone.
Refer to the Medal II Applied Alone section for weeds controlled by Medal II and to the
Scepter label for weeds controlled by Scepter. Refer to the Scepter label for
geographical locations where this tank mixture may be applied.
Apply Medal II + Scepter preplant incorporated or preemergence, using rates in Table
12. Follow use directions under Application Instructions on the Scepter label. For
preplant incorporated applications, apply and incorporate within 30 days before planting.
Observe all other precautions and limitations on the Scepter labels.
Table 12: Medal II + Scepter - Soybeans
Broadcast Rates Per Acre
Soil Texture
COARSE
MEDIUM
FINE
Less Than 3%
Organic Matter
Medal II
0.8 pt.
1 .0 pt.
1 .33 pts.
Scepter
0.67 pt.
0.67 pt.
0.67 pt.
3% or More
Organic Matter
Medal II
1.0pt.
1 .33 pts.
1.33-1. 67* pts.
Scepter
0.67 pt.
0.67 pt.
0.67 pt.
Muck or Peat
(soils with more than
20% organic matter)
DO NOT USE
"Use the higher rate of Medal II if heavy weed infestations are expected.

-59-
Restrictions: (1) Do not apply within 90 days of harvest, and (2) Do not graze or feed
treated soybean forage, hay, or straw to livestock, or illegal residues may result.
TANK MIXTURE WITH LOROX PLUS
This tank mixture controls all weeds controlled by Medal II alone and by Lorox Plus
alone. Refer to the Medal II Applied Alone section for weeds controlled by Medal II
and to the Lorox Plus label for weeds controlled by Lorox Plus.
Apply Medal II + Lorox Plus preemergence after planting, but before soybeans emerge,
using rates in Table 13.
Note: Follow all use directions, limitations, precautions, information regarding
application to soybeans, and rotational restrictions on the Medal II and Lorox Plus
labels.
Table 13: Medal II + Lorox Plus - Soybeans
Soil Texture
COARSE
MEDIUM
FINE
Broadcast Rates Per Acre
0.5 - 3% Ore
Medal II
0.8 pt.
1 .0 pt.
1.33pts.
anic Matter
Lorox Plus (60DF)
12-14 oz.
14-1 6 oz.
16-1 8 oz.
Restriction: Do not apply to sand, or to any soil with less than 0.5% organic matter, or
to any soil with pH greater than 6.8.
TANK MIXTURE WITH GEMINI
This tank mixture controls all weeds controlled by Medal II alone and by Gemini alone.
Refer to the Medal II Applied Alone section for weeds controlled by Medal II and to the
Gemini label for weeds controlled by Gemini.
Apply Medal II + Gemini preemergence after planting, but before soybeans emerge,
using rates in Table 14.
Note: Follow all use directions, limitations, precautions, restrictions, and information
regarding application to soybeans, and rotational restrictions on the Medal II and Gemini
labels.

r r-60-
Table 14: Medal II + Gemini - Soybeans
Soil Texture
COARSE (Sandy loam only)
MEDIUM
FINE
Broadcast Rates Per Acre
0.5 - 3% Organic Matter
Medal II
0.8 pt.
1.0pt.
1 .33 pts.
Gemini (60DF)
12-16 oz.
16-20oz.
20-24 oz.
Restriction: Do not apply to sand or loamy sand, or to any soil with less than 0.5%
organic matter, or to any soil with pH greater than 7.0, except as noted on the Gemini
label.
TANK MIXTURE WITH CANOPY
This tank mixture controls all weeds controlled by Medal II alone and by Canopy alone.
Refer to the Medal II Applied Alone section for weeds controlled by Medal II and to the
Canopy label for weeds controlled by Canopy.
Apply preplant incorporated or preemergence, using the appropriate rates from Table
15. Preplant Incorporated: Apply within 2 weeks of planting. Uniformly incorporate
into the top 1-2 inches of soil before planting soybeans. Preemergence: Apply after
planting, but before soybeans emerge.
Note: Follow all use directions, varietal restrictions, limitations, precautions, information
regarding application to soybeans, and rotational restrictions on the Medal II and
Canopy labels.
Table 15: Medal II + Canopy - Soybeans
Broadcast Rates Per Acre
Soil Texture
COARSE
MEDIUM
FINE
0.5% to Less Than 3%
Organic Matter
Medal II
0.8 pt.
1.0pt.
1 .33 pts.
Canopy 75DF
6.0-1 Ooz.
8.0-1 2 oz.
10-1 4 oz.
3-5% Organic Matter
Medal II
1.0pt.
1 .33 pts.
1.33-1 .67 pts.
Canopy 75DF
6.0-1 Ooz.
8.0-1 2 oz.
10-1 4 oz.
Restriction: Do not apply to sand, or to any soil with less than 0.5% organic matter, or
to any soil with pH greater than 7.0, except as noted on the Canopy label.

r -61-
TANK MIXTURE WITH PREVIEW
This tank mixture controls all weeds controlled by Medal II alone and by Preview alone.
Refer to the Medal II Applied Alone section for weeds controlled by Medal II and to the
Preview label for weeds controlled by Preview.
Apply preplant incorporated or preemergence, using the appropriate rates from Table
16. Preplant Incorporated: Apply within 2 weeks of planting. Uniformly incorporate
into the top 1-2 inches of soil before planting soybeans. Preemergence: Apply after
planting, but before soybeans emerge.
Note: Follow all use directions, varietal and other restrictions, limitations, precautions,
and information regarding application to soybeans, and rotational restrictions on the
Medal II and Preview labels.
Table 16: Medal II + Preview - Soybeans
Soil Texture
COARSE
MEDIUM
FINE
Broadcast Rates Per Acre
0.5% to Less Than 3%
Organic Matter
Medal II
0.8 pt.
1.0pt.
1.33pts.
Preview 75DF
6.0 oz.
7.0 oz.
8.0 oz.
3-5% Organic Matter
Medal II
1 .0 pt.
1.33pts.
1.33-1. 67 pts.
Preview 75DF
7.0 oz.
8.0 oz.
9.0-1 Ooz.
Restriction: Do not apply to sand, or to any soil with less than 0.5% organic matter, or
to any soil with pH greater than 6.8.
TANK MIXTURE WITH COMMAND*
This tank mixture controls all weeds controlled by Medal II alone and by Command
alone. Refer to the Medal II Applied Alone section for weeds controlled by Medal II
and to the Command label for weeds controlled by Command.
Apply Medal II + Command preplant incorporated, using rates in Table 17. Follow all
Command application instructions as to incorporation interval, geographical location,
equipment operation, soil moisture conditions, etc.
*Note: Before making applications, read and strictly follow all use directions, limitations,
restrictions, precautions, and information regarding application to soybeans, and
rotational restrictions on the Medal II and Command labels.

r-62-
Table 17: Medal II + Command - Soybeans
Soil Texture
COARSE
MEDIUM
FINE
Broadcast Rates Per Acre
Medal II
0.5-3%
Organic Matter
0.8pt.
1.0pt.
1 .33 pts.
Greater Than
3% Organic
Matter
1 .0 pt.
1 .33 pts.
1 .33-1 .67 pts.
Command 4E
Northern Area
1.5-2.0 pts.
1.5r2.0pts.
1.5-2.0 pts.
Southern Area
2.0-2.5 pts.
2.0-2.5 pts.
2.0-2.5 pts.
TANK MIXTURE WITH SONALAN
This tank mixture controls all weeds controlled by Medal II alone and by Sonalan alone.
Refer to the Medal II Applied Alone section for weeds controlled by Medal II and to the
Sonalan label for weeds controlled by Sonalan.
Apply Medal II and Sonalan preplant incorporated, using the appropriate rates from
Table 18.
Preplant Incorporated: Follow recommended soil preparation procedures for Sonalan.
Sequential: Apply Sonalan alone preplant incorporated as specified on the Sonalan
label. Follow with a preemergence application of Medal II during planting (behind the
planter) or after planting, but before weeds or soybeans emerge.
Table 18: Medal II + Sonalan - Soybeans
Broadcast Rates Per Acre
Soil Texture
COARSE
MEDIUM*
FINE*
Less Than 3% Organic Matter
Medal II
1.0-1 .33 pts.
1.33-1 .67 pts.
1.33-1 .67 pts.
Sonalan
1 .25-2.0 pts.
1.75-2.5 pts.
2.25-3.0 pts.
3% or More Organic Matter
Medal II
1.33 pts.
1.33-1 .67 pts.
1.67-2. Opts.
Sonalan
1.25-2.0 pts.
1.75-2.5 pts.
2.25-3.0 pts.
Muck or Peat
(soils with more
than 20%
organic matter)
DO NOT USE
*For eastern black nightshade on these soils, apply Sonalan at 3.0 pts./A on medium
and 3.5 pts./A on fine-textured soils, and follow with 2 incorporation passes.
Note: Follow all use directions, limitations, restrictions, precautions, and information
regarding application to soybeans on the Medal II and Sonalan labels.

-63-
TANK MIXTURE WITH PURSUIT
This tank mixture controls all weeds controlled by Medal II alone and by Pursuit alone.
Refer to the Medal II Applied Alone section for weeds controlled by Medal II and to the
Pursuit label for weeds controlled by Pursuit. Refer to the Pursuit label for geographical
locations where this tank mixture may be applied.
Apply Medal II + Pursuit early preplant, preplant incorporated, or preemergence after
planting, using rates in Table 19. Application can be made in water or liquid fertilizer.
Follow all use directions under Soil Applications on the Pursuit label. For early preplant
and preplant incorporated applications, apply within 30 days before planting.
Note: Follow all use directions, limitations, precautions, information regarding
application to soybeans, and rotational restrictions on the Medal II and Pursuit labels.
Table 19: Medal II + Pursuit - Soybeans
Soil Texture
COARSE
MEDIUM
FINE
Broadcast Rates Per Acre
Less Than 3%
Organic Matter
Medal II
0.8 pt.
1 .0 pt.
1 .33 pts.
3% or More
Organic Matter
Medal II
1.0pt.
1 .33 pts.
1.33-1 .67 pts.
Less Than 3% -
3% or More
Organic Matter
Pursuit
0.25 pt.
0.25 pt.
0.25 pt.
Sequential: Apply Medal II early preplant, preplant incorporated, or preemergence
after planting at 0.8 pt./A on coarse soils and 1.0 pt./A on medium- and fine-textured
soils. Follow with a sequential postemergence application of Pursuit to control emerged
weeds according to the Pursuit label. Medal II will improve the consistency and level of
control from Pursuit on most grass species. Refer to the Pursuit postemergence label
for a listing of weeds controlled, application rate, and growth stage limitations.
TANK MIXTURE WITH LEXONE, SENCOR, SCEPTER, LOROX, LOROX PLUS,
GEMINI, CANOPY, PREVIEW, OR PURSUIT, PLUS GRAMOXONE INTEON OR
ROUNDUP FOR MINIMUM-TILLAGE OR NO-TILLAGE SYSTEMS
In minimum-tillage or no-tillage systems where soybeans are planted directly into a
cover crop, stale seedbed, established sod, or previous crop residues, the contact
herbicides Gramoxone Inteon or Roundup may be added to a tank mix of either Medal II
+ Sencor or Lexone, Medal II + Scepter, Medal II + Lorox, Medal II + Lorox Plus, Medal
II + Gemini, Medal II + Canopy, Medal II + Preview, or Medal II + Pursuit. When used
as directed, the Gramoxone Inteon portion of the tank mixture controls most emerged
weeds and suppresses many perennial weeds. Roundup combinations will control
emerged annual and perennial weeds when applied as directed on the Roundup label.

-64-
The Medal II + Sencor/Lexone, Scepter, Lorox, Lorox Plus, Gemini, Canopy, Preview,
or Pursuit portion of the tank mixture provides preemergence control of the weeds listed
on this label in the tank mixture section for Medal II + Sencor/Lexone, Medal II +
Scepter, Medal II + Lorox, Medal II + Lorox Plus, Medal II + Gemini, Medal II + Canopy,
Medal II + Preview, and Medal II + Pursuit, respectively.
Refer to the label of each product used in combination and observe the planting details,
soybean variety restrictions, information regarding application to soybeans,
geographical restrictions, and all other precautions and limitations.
Refer below for rates of Gramoxone Inteon or Roundup, Medal II + Sencor/Lexone,
Medal II + Scepter, Medal II + Lorox, Medal II + Lorox Plus, Medal II + Gemini, Medal II
+ Canopy, Medal II + Preview, and Medal II + Pursuit, respectively.
Application: Apply before, during, or after planting, but before the soybeans emerge,
at the rates specified below. Add Gramoxone Inteon or Roundup at the following
broadcast rates:
Gramoxone Inteon: 1.5-2.0, 2.0-2.5, or 2.5-3.0 pts./A to 1-3, 3-6, or 6-inch tall weeds,
respectively. Apply surfactant at 1.0 or 2.0 pts./100 gals, of spray mixture with 75% or
greater or 50-74% nonionic active ingredient, respectively. This treatment will not
control weeds taller than 6 inches.
Restriction: Do not apply combinations containing Gramoxone Inteon in suspension-
type liquid fertilizers, as the activity of paraquat will be reduced.
Roundup: See the Roundup or Roundup RT label for weeds controlled, recommended
rates, and other use directions.
Apply in 20-60 gals, of water or fluid fertilizer per acre with ground equipment.
Medal II + Lexone/Sencor + Gramoxone Inteon or Roundup
On loamy sand with over 2% organic matter, apply 1.0 pt./A of Medal II + 0.33-0.5 Ib./A
of Sencor or Lexone DF. On medium soils, apply 1.33 pts./A of Medal II + 0.5-0.67 Ib./A
of Sencor or Lexone DF. On fine soils, apply 1.33-1.67 pts./A of Medal II + 0.67 Ib./A of
Sencor or Lexone DF.
*When using Sencor 4 or Lexone 4L, multiply Ibs. of DF by 1.5 to get pts./A.
Restrictions and Precautions: To avoid crop injury, (1) Do not use this tank mixture on
soil with less than 0.5% organic matter, on alkaline soil with a pH over 7.4, or on all
sand and on loamy sand with less than 2% organic matter. (2) If heavy rain occurs
soon after application, crop injury may result, especially in poorly drained areas where
water stands for several days, or where the seeding slit has not been properly closed.

IS-65-
Medal II + Scepter + Gramoxone Inteon or Roundup
On coarse so/7s, apply 1.0 pt./A of Medal II + 0.67 pt./A of Scepter. On medium soils,
apply 1.33 pts./A of Medal II + 0.67 pt./A of Scepter. On fine soils, apply 1.67 pts./A of
Medal II + 0.67 pt./A of Scepter.
Restrictions: (1) Do not apply within 90 days of harvest, and (2) Do not graze or feed
treated soybean forage, hay, or straw to livestock, or illegal residues may result.
Medal II + Lorox + Gramoxone Inteon or Roundup
On coarse soils*, apply 1.0 pt./A of Medal II + 1.0-1.5 Ibs./A of Lorox DF**. On medium
soils, apply 1.33 pts./A of Medal II + 1.0-2.0 Ibs./A of Lorox DF. On fine soils, apply
1,33-1.67 pts./A of Medal II.+ 2.0-3.0 Ibs./A of Lorox DF.
*Do not use on loamy sand, except in the northeastern U.S. on loamy sand with over
1% organic matter, or injury may occur. Do not use on sand, gravelly soils, or
exposed subsoils, or injury may occur.
**When using Lorox L or Lorox DF, use equivalent rates. One pt. of Lorox L equals 1.0
Ib. of Lorox DF.
Restriction: Do not use on soil with less than 0.5% organic matter, or crop injury may
occur.
Medal II + Lorox Plus + Gramoxone Inteon or Roundup
Use only where soils have 0.5-3% organic matter. On coarse soils, apply 1.0 pt./A of
Medal II + 12-14 oz./A of Lorox Plus 60DF. On medium soils, apply 1.33 pts./A of
Medal II + 14-16 oz./A of Lorox Plus. On fine soils, apply 1.33-1.67 pts./A of Medal II +
16-18 oz./A of Lorox Plus.
Restriction: Do not apply to sand or to any soil with pH greater than 6.8.
Medal II + Gemini + Gramoxone Inteon or Roundup
Use only where soils have 0.5-3% organic matter. On coarse soils (sandy loam only),
apply 1.0 pt./A of Medal II + 12-16 oz./A of Gemini 60DF. On medium soils, apply
1.33 pts./A of Medal II + 16-20 oz./A of Gemini. On fine soils, apply 1.33-1.67 pts./A of
Medal II + 20-24 oz./A of Gemini.
Restriction: Do not apply to sand or loamy sand, or to any soil with less than 0.5%
organic matter, or to any soil with pH greater than 7.0, except as noted on the Gemini
label.

-66-
Medal II + Canopy + Gramoxone Inteon or Roundup
Use only where soils have 0.5-5% organic matter. On coarse soils (except sand), apply
1.0 pt./A of Medal II, on medium soils, apply 1.33 pts./A of Medal II, and on fine soils,
apply 1.33-1.67 pts./A of Medal II. Refer to the Canopy label for appropriate rate,
according to geographical location, soil and organic matter classification, pH limitations,
and all other use directions.
Restriction: Do not apply to sand, or to any soil with less than 0.5% organic matter, or
to any soil with pH greater than 7.0, except as noted on the Canopy label.
Medal II + Preview + Gramoxone Inteon or Roundup
Use only where soils have 0.5-5% organic matter. On coarse soils (except sand), apply
1.0 pt./A of Medal II + 6.0*-7.0 oz./A of Preview 75DF. On medium soils, apply
1.33 pts,/A of Medal II + 7.0*-8.0 oz./A of Preview. On fine soils, apply 1.33-1.67 pts./A
of Medal II + 8.0* to 9.0-10 oz./A of Preview.
*Use this rate where the soil organic matter is in the 0.5 to less than 3% range.
Restriction: Do not apply to sand, or to any soil with less than 0.5% organic matter, or
to any soil with pH greater than 6.8.
Medal II + Pursuit + Gramoxone Inteon or Roundup
On coarse soils, apply 1.0 pt./A of Medal II + 0.25 pt./A of Pursuit. On medium soils,
apply 1.33 pts./A of Medal II + 0.25 pt./A of Pursuit. On fine soils, apply 1.67 pts./A of
Medal II + 0.25 pt./A Pursuit.
POSTEMERGENCE USE ON SOYBEANS - MEDAL II TANK MIXTURES
Tank Mixture with Glyphosate Products
Medal II at 1.0-1.33 pts./A may be tank mixed with glyphosate products at labeled rated
and applied from emergence up through the third trifoliate leaf stage of Roundup Ready
or glyphosate-tolerant soybeans. Medal II alone will not control emerged weeds. Use
this treatment only on soybeans designated for use with glyphosate (e.g., Roundup
Ready or glyphosate-tolerant soybeans). The glyphosate product must be registered
for postemergence use in Roundup Ready or glyphosate-tolerant soybeans.
Tank Mixture with Pursuit
Medal II at 1.0-1.33 pts./A may be tank mixed with Pursuit at labeled rates and applied
from emergence up through the third trifoliate leaf stage of soybeans. Medal II alone
will not control emerged weeds.

( 4,1 IS
-67-
Tank Mixture with Glufosinate Ammonium (Liberty) Products
Medal II at 1.0-1.33 pts./A may be tank mixed with glufosinate products at labeled rates
and applied from emergence up through the third trifoliage leaf stage of soybeans.
Medal II alone will not control emerged weeds. Use this treatment only on soybeans
designated for use with glufosinate (e.g., Liberty Link).
Note: Follow the tank mix product label for adjuvant recommendations. The use of
COC or UAN with Medal II may result in temporary crop injury. To avoid possible illegal
residues when Medal II is applied postemergence to soybeans: (1) Do not apply more
than 1.33 pts./A postemergence. (2) Make postemergence application at least 90 days
before harvest. (3) Do not graze or feed treated forage or hay from soybeans to
livestock following a postemergence application of Medal II.
STORAGE AND DISPOSAL
Pesticide Storage
This product may be stored at temperatures down to 30 degrees below 0°F.
Pesticide Disposal
Do not contaminate water, food, or feed by storage or disposal. Open dumping is
prohibited. Wastes resulting from the use of this product are toxic. Improper disposal of
unused pesticide, spray mixture, or rinsate is a violation of federal law. Pesticide, spray
mixture, or rinsate that cannot be used according to label instructions must be disposed
of according to federal, state, or local procedures. For guidance in proper disposal
methods, contact your State Pesticide or Environmental Control Agency, or the
Hazardous Waste representative at the nearest EPA Regional Office.
Container Handling (less than 5 gallons)
Non-refillable container. Do not reuse or refill this container. Offer for recycling if
available. Triple rinse container (or equivalent) promptly after emptying. Triple rinse as
follows: Empty the remaining contents into application equipment or a mix tank and
drain for 10 seconds after the flow begins to drip. Fill the container % full with water and
recap. Shake for 10 seconds. Pour rinsate into application equipment or a mix tank or
store rinsate for later use and disposal. Drain for 10 seconds after the flow begins to
drip. Repeat this procedure two more times. Then offer for recycling if available or
puncture and dispose of in a sanitary landfill, or by incineration, or, if allowed by state
and local authorities, by burning. If burned, stay out of smoke.
For minor spills, leaks, etc., follow all precautions indicated on this label and clean up
immediately. Take special care to avoid contamination of equipment and facilities

70J7S
-68-
during cleanup procedures and disposal of wastes. In the event of a major spill, fire, or
other emergency, call 1-800-888-8372, day or night.
Container Handling (Bulk/Mini-Bulk)
Refillable container. Refill this container with pesticide only. Do not reuse this container
for any other purpose. Cleaning the container before final disposal is the responsibility
of the person disposing of the container. Cleaning before refilling is the responsibility of
the person refilling. To clean container before final disposal, empty the remaining
contents from this container into application equipment or mix tank. Fill the container
about 10 percent full with water. Agitate vigorously or recirculate water with the pump
for 2 minutes. Pour or pump rinsate into application equipment or rinsate collection
system. Repeat this rinsing procedure two more times. Then offer for recycling if
available or puncture and dispose of in a sanitary landfill, or by incineration, or by other
procedures allowed by state and local authorities.
For minor spills, leaks, etc., follow all precautions indicated on this label and clean up
immediately. Take special care to avoid contamination of equipment and facilities
during cleanup procedures and disposal of wastes. In the event of a major spill, fire, or
other emergency, call 1-800-888-8372, day or night.
AAtrex®, AAtrex® Nine-O®, Beacon®, Bicep MAGNUM®, Bicep II MAGNUM®, Bicep
Lite II MAGNUM®, Caparol®, Concep®, Dual MAGNUM®, Dual II MAGNUM®,
Eptam®, Eradicane® Evik®, Exceed®, Gramoxone Inteon®, Medal®, Princep®,
Princep® Caliber® 90, Starfire®, and the Syngenta logo are trademarks of a Syngenta
Group Company
Accent®, Canopy®, Gemini®, Lexone®, Lorox®, Lorox Plus®, Preview® and Viton®
trademarks of E. I. duPont de Nemours and Company, Inc.
Ag-Chem RoGator® trademark of Ag-Chem Equipment Company
Agsorb® trademark of Oil-Dri Corporation
Balan®, Sonalan®, and Treflan® trademarks of Dow AgroSciences
Balance® PRO, Brominal®, and Buctril® trademarks of Aventis
Banvel®, Banvel SGF®, Basagran®, Clarity®, Marksman®, and Storm® trademarks of
BASF Corporation
Celatom MP-79® trademark of Eagle-Picher Industries, Inc.
Command® trademark of FMC Corporation

f f fl -69-
Compex® trademark of KALO Agricultural Chemicals, Inc.
Cotoran® trademark of Griffin LLC
Hi-Cycle™ trademark of John Deere Company
Landmaster®, Roundup®, Roundup Ultra™, Roundup Ready® trademarks of
Monsanto Company
Liberty®, LibertyLink®, Sencor® trademarks of Bayer CropScience
Prowl®, Pursuit®, and Scepter® trademarks of American Cyanamid Company
Tyler Patriot™ trademark of Tyler Ltd. Partnership
Unite® trademark of HACO, Inc.
Weedone® trademark of NuFarm, Inc.
Willmar Air Ride® trademark of Willmar Manufacturing
X-77® trademark of Loveland Industries, Inc.
©201X Syngenta
Manufactured for:
Syngenta Crop Protection, LLC
P.O. Box 183001
Greensboro, North Carolina 27419-8300
SCP 965A-L1
SCP 965A-L2

-70-
[Container Label - 2.5 gallon]
GROUP mim HERBICIDE
Note: It is illegal to sell, use or distribute this product within, or into, Nassau County or
Suffolk County, New York.
Medal® II
Herbicide
For weed control in corn, cotton, peanuts, pod crops, potatoes, safflowers, grain or
forage sorghum, and soybeans
Active Ingredient:
S-metolachlor (CAS No. 87392-12-9) 82.4%
Other Ingredients: 17.6%
Total: 100.0%
Medal II contains 7.64 Ibs. of active ingredient per gallon.
KEEP OUT OF REACH OF CHILDREN.
CAUTION
See directions for use in attached booklet.
AGRICULTURAL USE REQUIREMENTS
Use this product only in accordance with its labeling and with the Worker Protection
Standard, 40 CFR part 170. Refer to supplemental labeling under "Agricultural Use
Requirements" in the Directions for Use section for information about this standard.
Product of Switzerland
Manufactured in the USA
EPA Reg. No. 100-965
EPAEst. 11773-IA-01VVVC
(Superscript is first three letters of batch code on container)
2.5 gallons
Net Contents

C -71-
Precautionary Statements
Hazards to Humans and Domestic Animals
Causes eye irritation. Harmful if swallowed or absorbed through skin. Avoid contact
with eyes, skin, or clothing. This product may cause skin sensitization reactions in
some people.
FIRST AID
If in eyes
If on skin or
clothing
If swallowed
If inhaled
• Hold eye open and rinse slowly and gently with water for 15-20
minutes.
• Remove contact lenses, if present, after the first 5 minutes, then
continue rinsing eye.
• Call a poison control center or doctor for treatment advice.
• Take off contaminated clothing.
• Rinse skin immediately with plenty of water for 1 5-20 minutes.
• Call a poison control center or doctor for treatment advice.
• Call a poison control center or doctor immediately for treatment
advice.
• Do not give any liquid to the person.
• Do not induce vomiting unless told to do so by the poison control
center or doctor.
• Do not give anything by mouth to an unconscious person.
• Move person to fresh air.
• If person is not breathing, call 91 1 or an ambulance, then give
artificial respiration, preferably mouth-to-mouth, if possible.
• Call a poison control center or doctor for further treatment advice.
Have the product container or label with you when calling a Poison Control Center or
doctor, or going for treatment.
HOT LINE NUMBER
For 24 Hour Medical Emergency Assistance (Human or Animal)
Or Chemical Emergency Assistance (Spill, Leak, Fire or Accident),
Call
1-800-888-8372
Environmental Hazards
Do not apply directly to water, to areas where surface water is present, or to intertidal
areas below the mean high water mark. Do not contaminate water when disposing of
equipment wash water or rinsate.

r -72-
Ground Water Advisory
The active ingredient in Medal II has the potential to leach through soil into ground
water under certain conditions as a result of agricultural use. Use of this chemical in
areas where soils are permeable, particularly where the water table is shallow, may
result in ground water contamination.
Surface Water Advisory
The active ingredient in Medal II has the potential to contaminate surface water through
ground spray drift. Under some conditions, the active ingredient may also have a high
potential for runoff into surface water (primarily via dissolution in runoff water) for
several months post-application. These include poorly drained or wet soils with readily
visible slopes toward adjacent surface waters, frequently flooded areas, areas
overlaying extremely shallow ground water, areas with in-field canals or ditches that
drain to surface water, areas not separated from adjacent surface waters with vegetated
filter strips, and areas overlaying tile drainage systems that drain to surface water.
Mixing/Loading Instructions
Care must be taken when using this product to prevent back-siphoning into wells, spills,
or improper disposal of excess pesticide, spray mixtures, or rinsates.
Check-valves or antisiphoning devices must be used on all mixing and/or irrigation
equipment.
This product may not be mixed or loaded within 50 ft. of perennial or intermittent
streams and rivers, natural or impounded lakes and reservoirs. This product may not
be mixed/loaded or used within 50 ft. of all wells, including abandoned wells, drainage
wells, and sink holes*.
*For exceptions to this restriction, see the Environmental Hazards section of the
Precautionary Statements in attached booklet.
Aerial Drift Management Requirements
Do not apply this product by air, unless the supplemental labeling on Aerial Drift
Management in attached booklet is followed.
Chemigation
Refer to supplemental labeling in attached booklet for use directions for chemigation.
Do not apply this product through any irrigation system, unless the supplemental
labeling on chemigation is followed.

-73-
Container Handling
Non-refillable container. Do not reuse or refill this container. Offer for recycling if
available. Triple rinse container (or equivalent) promptly after emptying. Triple rinse as
follows: Empty the remaining contents into application equipment or a mix tank and
drain for 10 seconds after the flow begins to drip. Fill the container % full with water and
recap. Shake for 10 seconds. Pour rinsate into application equipment or a mix tank or
store rinsate for later use and disposal. Drain for 10 seconds after the flow begins to
drip. Repeat this procedure two more times. Then offer for recycling if available or
puncture and dispose of in a sanitary landfill, or by incineration, or, if allowed by state
and local authorities, by burning. If burned, stay out of smoke.
Medal II™ and the Syngenta logo are trademarks of a Syngenta Group Company
©201XSyngenta
Manufactured for:
Syngenta Crop Protection, LLC
P.O. Box 18300
Greensboro, North Carolina 27419-8300
SCP 965A-L1 [2.5 gallon booklet, Product ID 25060]
SCP 965A-L2 [Bulk booklet, Product ID 25061]
MEDAL II 965 MAS 0809 AMENDE APR2011 - bb - 7-6-11
000100-00965.20110401B.MEDAL-ll_AMEND_APR2011.pdf