# CANSIO HERBICIDE

- EPA Reg No: **279-9630**
- Registrant: FMC CORPORATION 
- Signal word: Caution
- Active ingredients: Metribuzin (64.3%); Thifensulfuron (7.1%); Tribenuron-methyl (3.6%)
- Label accepted: 2019-09-23
- Source PDF: https://www3.epa.gov/pesticides/chem_search/ppls/000279-09630-20190923.pdf

---
September 23, 2019
Subject;
Dear Mr. Ambrose;
Reg Review Label Acceptable v.20151230
OFFICE OF CHEMICAL SAFETY 
AND POLLUTION PREVENTION
Should you wish to add/retain a reference to the company’s website on your label, then please be 
aware that the website becomes labeling under the Federal Insecticide Fungicide and Rodenticide 
Act and is subject to review by the Agency. If the website is false or misleading, the product 
would be misbranded and unlawful to sell or distribute under FIFRA section 12(a)(1)(E). 40 
CFR 156.10(a)(5) list examples of statements EPA may consider false or misleading. In addition, 
regardless of whether a website is referenced on your product’s label, claims made on the 
website may not substantially differ from those claims approved through the registration process. 
Therefore, should the Agency find or if it is brought to our attention that a website contains false 
or misleading statements or claims substantially differing from the EPA approved registration, 
the website will be referred to the EPA’s Office of Enforcement and Compliance.
The Agency, in accordance with the Federal Insecticide, Fungicide and Rodenticide Act 
(FIFRA), as amended, has completed reviewing all of the information submitted with your 
application to support the Registration Review of the above referenced product in connection 
with the 22 Sulfonylurea (SU) Herbicides Interim Decision, and has concluded that your 
submission is acceptable. The label referred to above, submitted in coimection with registration 
under FIFRA, as amended, is acceptable.
A copy of your label stamped “Accepted” is enclosed. Products shipped after 12 months from the 
date of this amendment must bear the new revised label. Your release for shipment of the 
product bearing the amended label constitutes acceptance of these conditions. If these conditions 
are not complied with, the registration will be subject to cancellation in accordance with FIFRA 
section 6.
Richard Ambrose
FMC Corporation
c/o FMC Stine Research Center 
P.O. Box 30
Newark, Delaware 19714-0030
UNITED STATES ENVIRONMENTAL PROTECTION AGENCY 
WASHINGTON, DC 20460
Registration Review Label Mitigation for Thifensulfuron Methyl and Tribenuron- 
methyl
Product Name; Cansio Herbicide
Application Date; 5/2/2019
EPA Registration Number; 279-9630 (formerly 352-912)
Decision Number; 551678; 554903

Sincerely,
Enclosure
Linda Arrington, Branch Chief
Risk Management and Implementation Branch 4
Pesticide Re-Evaluation Division
Office of Pesticide Programs
If you have any questions about this letter, please contact Jaclyn Pyne by phone at 703-347- 
0445, or via email at pyne.jaclyn@epa.gov.
Page 2 of 2
EPAReg. No. 279-9630
Decision No. 551678; 554903

CANSIO™
HERBtCJOE
EPA Est. No. 
OR
Sold B ACCEPTEDSold By
•fAac Sep 23,2019
279-96301
5
2
2
FMC Corporation
2929 Walnut Street 
Philadelphia, PA 19104
METRIBUZIN
THIFENSULFURON-METHYL
TRIBENURON-METHYL
GROUP
GROUP
GROUP
HERBICIDE
HERBICIDE
HERBICIDE
Refillable Container
Net: 
,.Jriyi?r Lni; FtKJfjrgi . Fyiigiclde
<!iid RDdenucicie Ad as amended, lor the 
pssilicide registered under 
EPA Reg. No.
Dry flowable
For control of certain grasses and broadleaf
weeds in spring and winter barley, winter wheat, fallow and burndown
Active Ingredient_______________________________________________________
Metribuzin 
Thifensulturon-methyl
Tribenuron-methyl
Other Ingredients
TOTAL
EPA Reg. No. 279-9630
Contains 0.75 lb. active ingredient per pound (metribuzin 0.643, thifensulfuron-methyl 0.071, & tribenuron-methyl 0.036 per 
poimd)
Nonrefillable Container
Net: 
By ff^eight 
64.3% 
7.1% 
3.6% 
25.0%
100.0%
KEEP OUT OF REACH OF CHILDREN
CAUTION
Si usted no entiende la etiqueta, busque a alguien para que se la explique a usted en detalle. (If you do not understand this 
label, find someone to explain it to you in detail.)
FIRST AID
IF SWALLOWED: Call poison control center or doctor immediately for treatment advice. Have person sip a glass of 
water if able to swallow. Do not induce vomiting unless told to do so by a poison control center or doctor. Do not give 
anything to an unconscious person,
IF ON SKIN OR CLOTHING: Take off contaminated clothing. Rinse skin immediately with plenty of water for 15-20 
minutes. Call a poison control center or doctor for treatment advice.
IF INHALED: Move person to fresh air. If person is not breathing, call 911 or ambulance, then give artificial respiration, 
preferably mouth-to-mouth, if possible. Call a poison control center or doctor for treatment advice. 
IF IN EYES: Hold eye open and rinse slowly and gently with water for 15-20 minutes. Remove contact lenses, if present, 
after the first 5 minutes, then continue rinsing eye. Call a poison control center or doctor for further treatment advice. 
Have the product container or label with you when calling a poison control center or doctor or going for treatment. You 
may also contact 1-800-331-3148 for emergency medical treatment information.
PRECAUTIONARY STATEMENTS
HAZARDS TO HUMANS AND DOMESTIC ANIMALS
CAUTION
Harmful if swallowed. Harmful if absorbed through skin. Harmful if inhaled. Causes moderate eye irritation. Avoid contact 
with eyes, skin, or clothing. Avoid breathing dust. Prolonged or frequently repeated skin contact may cause allergic 
reactions in some individuals. Wash thoroughly with soap and water after handling and before eating, drinking, chewing 
gum, using tobacco, or using the toilet.
For medical emergencies involving this product, call toll-free 1-800-331-3148.
PERSONAL PROTECTIVE EQUIPMENT (PPE)
Applicators and other handlers must wear:
Long-sleeved shirt and long pants
Chemical resistant gloves made of any waterproof material such as polyethylene or polyvinyl chloride. 
Shoes plus socks
Discard clothing and other absorbent materials that have been drenched, or heavily contaminated with this product. 
Follow manufacturer’s instructions for cleaning/maintaining PPE. If no such instruction for washables exists, use detergent 
and hot water. Keep and wash PPE separately from other laundry.

2
IMPORTANT : When reduced PPE is worn because a closed system is being used, handlers must be provided all 
PPE specified above for "applicators and other handlers" and have such PPE immediately available for use in an 
emergency, such as a spill or equipment break-down.
ENGINEERING CONTROL
When handlers use closed systems, enclosed cabs, or aircraft in a manner that meets the requirements listed in the 
Worker Protection Standard (WPS) for agricultural pesticides (40 CFR 170.240(d)(4-6), the handler PPE 
requirements may be reduced or modified as specified in the WPS.
ENVIRONMENTAL HAZARDS
Do not apply directly to water, to areas where surface water is present or to intertidal areas below the mean 
highwater mark. Do not apply when weather conditions favor drift from areas treated. Do not contaminate water 
when disposing of equipment washwaters or rinsate.
Groundwater Advisory
Metribuzin is a chemical which can travel (seep or leach) through soil and can contaminate groundwater which may 
be used as drinking water. Metribuzin has been found in groundwater as a result of agricultural use. Users are 
advised not to apply metribuzin where the water table (groundwater) is close to the surface, and where the soils are 
very permeable, i.e., well drained soils such as loamy sands. Yom local agricultural agencies can provide further 
information on the type of soil in your area and the location of groundwater.
Surface Water Advisory
This product may impact surface water quality due to runoff of rain water. This is especially true for poorly draining 
soils and soils with shallow ground water. This product is classified as having high potential for reaching surface 
water via runoff for several weeks or more after application. A level, well-maintained vegetative buffer strip 
between areas to which this product is applied and surface water features such as ponds, streams, and springs will 
reduce the potential loading of this product from runoff water and sediment. Runoff of this product will be greatly 
reduced by avoiding applications when rainfall or irrigation is expected to occur within 48 horns.
Windblown Soil Particles Advisory
This product has the potential to move off-site due to wind erosion. Soils that are subject to wind erosion usually 
have a high silt and/or fine to very fine sand fractions and low organic matter content. Other factors which can affect 
the movement of windblown soil include the intensity and direction of prevailing winds, vegetative cover, site slope, 
rainfall, and drainage patterns. Avoid applying this product if prevailing local conditions may be expected to result 
in off-site movement.
Non-target Organism Advisory
This product is toxic to plants and may adversely impact the forage and habitat of non-target organisms, including 
pollinators, in areas adjacent to the treated area. Protect the forage and habitat of non-target organisms by 
minimizing spray drift. For further guidance and instructions on how to minimize spray drift, refer to the Spray Drift 
Management section of this label.
USER SAFETY RECOMMENDATIONS
USERS SHOULD: Wash thoroughly with soap and water after handling and before eating, drinking, chewing 
gum, using tobacco or using the toilet. Remove clothing/PPE immediately if pesticide gets inside. Then wash 
thoroughly and put on clean clothing. Remove PPE immediately after handling this product. Wash the outside of 
gloves before removing. As soon as possible, wash thoroughly and change into clean clothing.
DIRECTIONS FOR USE
It is a violation of Federal law to use this product in a manner inconsistent with its labeling.
DO NOT apply this product in a way that will contact workers or other persons, either directly or through drift. Only 
protected handlers may be in the area during application. For any requirements specific to your State or Tribe, consult the 
agency responsible for pesticide regulation.
CANSIO™ herbicide, referred to below as CANSIO herbicide, must be used only in accordance with the instructions on this 
label, or as otherwise permitted by FIFRA. Always read the entire label, including the Limitation of Warranty and Liability.

Do not apply, drain or flush equipment on or near desirable trees or other plants or on areas where their roots may 
extend, or in locations where the chemical may be washed or moved into contact with their roots.
Do not use on lawns, walks, driveways, or tennis courts.
Do not allow drift of spray to off-target plants.
o 
o
Do not apply CANSIO herbicide through any type of irrigation system. 
Do not apply when weather conditions favor spray drift.
Do not apply when sensitive or cool season crops, including cole crops, onions, peas, or strawberries are present in 
adjacent fields or in areas where wheat is growing in coarse textured soils.
Do not use low-pressure, high-volume hand wand equipment.
Do not apply to wheat and barley underseeded with another crop.
Do not store pesticides near a well that provides water.
Do not apply CANSIO herbicide by air in the state of New York.
Do not contaminate any body of water with product.
Do not apply aerially when CANSIO herbicide is tank-mixed with alachlor.
For applications, do not apply during a temperature inversion, when wind speed is less than 2 mph or above 10 mph, 
3
BIOLOGICAL ACTIVITY
CANSIO herbicide is absorbed through the foliage and roots of plants rapidly inhibiting the growth of susceptible weeds. 
One to 3 weeks after application to weeds (2 to 5 weeks for wild garlic), leaves of susceptible plants appear chlorotic, and 
the growing point subsequently dies. Following application of CANSIO herbicide susceptible weeds may germinate and 
emerge, but growth then ceases, and leaves become yellow and/or brown 3-5 days after emergence. Death of leaf tissue 
and growing point will follow in some species while others will remain green but stunted and noncompetitive. 
CANSIO herbicide provides the best control in vigorously growing crops that shade competitive weeds. Weed control in 
areas of thin crop stand or seeding skips may not be as satisfactory. However, a crop canopy that is too dense at application 
can intercept spray and reduce weed control.
The herbicidal action of CANSIO herbicide may be affected in crops stressed from adverse environmental conditions 
(including extreme temperatures or moisture), abnormal soil conditions, cultural practices, or variations in crop variety. In 
warm, moist conditions, the expression of herbicide symptoms is accelerated; in cold, dry conditions, expression of 
herbicide symptoms is delayed. In addition, weeds hardened-off by drought stress are less susceptible to CANSIO 
herbicide.
PRODUCT INFORMATION
CANSIO herbicide is a water dispersible granule that can be applied alone or in combination with other herbicides for 
selective control of broadleaf weeds and grasses in spring and winter barley, winter wheat, fallow and bumdown. 
When applied according to instructions on this label the best control is obtained when CANSIO herbicide is applied to 
young, actively growing weeds. The specified use rate will depend on weed spectrum and size of weed at time of 
application.
Residual applications of CANSIO herbicide require rainfall or sprinkler irrigation to activate the herbicide. Degree of 
control and duration of effect depend on; rate used, weed spectrum, growing conditions at and following time of 
treatment, weed size, soil pH, texture, organic matter, moisture and precipitation.
Best residual control is obtained if CANSIO herbicide is applied to moist soil and followed by rainfall or irrigation (~1”) 
before weeds germinate. Several small rainfalls of less than 1/4” each are not as beneficial as one large rainfall of 1/2-1”. 
On dry soil, more moisture is required for activation (1-2”) before weed emergence. If moisture is insufficient to activate 
the herbicide, a rotary hoeing or shallow cultivation needs to be made after emergence of the crop while weeds are small 
enough to be controlled by mechanical means. If heavy rains occur within 3 weeks of planting, crop injury may result.
RESTRICTIONS
• Injury to or loss of desirable trees or vegetation may result from failure to observe the following: 
o
AGRICULTURAL USE REQUIREMENTS
Use this product only in accordance with its labeling and with the Worker Protection Standard, 40 CFR part 170. This 
Standard contains requirements for the protection of agricultural workers on farms, forests, nursenes. and greenhouses, and 
handlers of agricultural pesticides. It contains requirements for training, decontamination, notification, and emergency 
assistance. It also contains specific instructions and exceptions pertaining to the statements on this label about personal 
protective equipment (PPE) and restricted-entry interval. The requirements in this box only apply to uses of this product that 
are covered by the Worker Protection Standard.
Do not enter or allow worker entry into treated areas dining the restricted entry interval (REI) of 12 hours. 
PPE required for early entry to treated areas that is permitted under the Worker Protection Standard and that involves 
contact with anything that has been treated, such as plants, soil, or water, is;
Coveralls
Chemical resistant glovesmade of any waterproof material.
Shoes plus socks

4
or when conditions favor poor coverage and/or off-target spray drift.
When using CANSIO herbicide in tank mixes or sequential applications with other products containing 
thifensulfuron-methyl and/ or, tribenuron-methyl. and/or metribuzin, do not exceed 0.0469 lb. ai/A thifensulfuron- 
methyl, 0.0156 lb. ai/A tribenuron-methyl, and 0.05 lb. ai/A metribuzin.
PRECAUTIONS
• Injiuy to or loss of adjacent sensitive crops and vegetation may result from failure to observe the following:
o Take all necessaiy' precautions to avoid all direct or indirect contact (including spray drift) with non-target 
plants or areas.
o Carefully observe all sprayer cleanup instructions both prior to and after using this product, as spray tank residue 
may damage crops other than those listed on this label.
• Calibrate sprayers only with clean water away from well sites.
• Make scheduled checks of spray equipment.
• Ensure that all operation employees accurately measiue pesticides.
• Mix only enough product for the job at hand.
• Avoid overfilling of spray tank.
• Dilute and agitate excess solution and apply at labeled rates or uses.
• When triple-rinsing the pesticide container, be sure to add the rinsate to the spray mix.
• For ground applications applied when dry, dusty field conditions exist, control of weeds in wheel track areas may be 
reduced.
• Refer to crop section for specific crop related restrictions andprecautions.
WEED RESISTANCE MANAGEMENT
CANSIO herbicide, which contains the active ingredients metribuzin, thifensulfuron-methyl and tribenuron-methyl are group 
2 or 5 herbicides based on the mode of action classification system of the Weed Science Society of America.
Proactively implementing diversified weed control strategies to minimize selection for weed populations resistant to one or 
more herbicides is a best practice. A diversified weed management program may include the use of multiple herbicides 
with different sites of action and overlapping weed spectrum with or without tillage operations and/or other cultural 
practices. Research has demonstrated that using the labeled rate and directions for use is important to delay the selection 
for resistance.
The continued effectiveness of this product depends on the successful implementation of a weed resistance management 
program.
To aid in the prevention of developing weeds resistant to this product, users should;
• Scout fields before application to ensure herbicides and rates will be appropriate for the weed species and weed sizes 
present.
• Start with a clean field, using either a bumdown herbicide application or tillage.
• Control weeds early when they are relatively small (less than 4 inches).
• Apply full rates of CANSIO herbicide, for the most difficult to control weed in the field at the specified time (correct 
weed size) to minimize weed escapes.
• Scout fields after application to detect weed escapes or shifts in control of weed species.
• Control weed escapes before they reproduce by seed or proliferate vegetatively.
• Report any incidence of non-performance of this product against a particular weed to your FMC representative, local 
retailer, or county extension agent.
• Contact your FMC representative, crop advisor, or extension agent to find out if suspected resistant weeds to these 
MO As have been found in your region. Do not assume that each listed weed is being controlled by multiple sites of 
action. Products with multiple active ingredients are intended to broaden the spectrum of weeds that are controlled. Some 
weeds may be controlled by only one of the active ingredients in this product.
• If resistance is suspected, treat weed escapes with an herbicide having a site of action other than Group 2 or 5 
and/or use nonchemical methods to remove escapes, as practical, with the goal of preventing further seed 
production.
• Suspected herbicide-resistant weeds may be identified by these indicators:
- Failure to control a weed species normally controlled by the herbicide at the dose applied, especially if control is 
achieved on adjacent weeds;
- A spreading patch of non-controlled plants of a particular weed species; and
- Surviving plants mixed with controlled individuals of the same species
Additionally, users should follow as many of the following herbicide resistance management practices as is practical:
• Use a broad-spectrum soil-applied herbicide with other sites of action as a foundation in a weed control program.
• Utilize sequential applications of herbicides with alternative sites of action.

TANK MIX COMPATIBILITY TESTING
Perform a jar test prior to tank mixing to ensure compatibility of CANSIO herbicide and other pesticides. Use a clear glass 
quart jar with lid and mix the tank mix ingredients in their relative proportions. Invert the jar containing the mixture 
several times and observe the mixture for approximately 1/2 hour. If the mixture balls-up, forms flakes, sludges, gels, oily 
film or layers, or other precipitates, it is not compatible.
Tank Mixing - The crop safety of all tank mixtures with CANSIO herbicide which may include physically compatible 
pesticides, fertilizers, adjuvants, and/or additives, has not been tested. When considering the use of a tank mixture on a 
labeled crop without prior experience, or which is not specifically described in the CANSIO herbicide product labeling or 
in other FMC product use instruction, it is important to first understand crop safety. To test for crop safety, prepare a small 
volume of the intended tank mixture, apply it to an area of the target crop as directed by both this and the tank mix partner 
product label(s) and observe the treated crop to ensure that a phytotoxic response does not occur. FMC will not be 
responsible for any crop injury arising from the use of a tank mixture that is not specifically described on the CANSIO 
herbicide product labeling or in other FMC product use instructions.
This product may be tank mixed with registered products for these uses including products containing the active 
ingredients 2,4-D, bromoxynil, dicamba, glufosinate, glyphosate, MCPA, paraquat, or saflufenacil in accordance with the 
most restrictive label limitations and precautions. DO NOT exceed label dosage rates. This product may not be mixed with 
any product containing a label prohibition against such mixing. Refer to crop specific information section of this label for 
additional information.
It is the pesticide user’s responsibility to ensure that all products are registered for the intended use. Read and follow the 
applicable restrictions and limitations and directions for use on all product labels involved in tank mixing. Users must 
follow the most restrictive directions for use and precautionary statements of each product in the tank mixture. If the 
instructions on the tank mix partner label conflicts with this CANSIO herbicide label, DO NOT use in a tank mixture with 
CANIO herbicide.
SOIL TEXTURE: As used on this label, “Coarse soils” are loamy sand or sandy loam soils. “Medium soils” are loam, silt
loam, silt, sandy clay, or sandy clay loam. “Fine soils” are silty clay, silty clay loam, clay, or clay loam. Silty clay loam soils
5
INTEGRATED PEST MANAGEMENT
This product may be used as part of an Integrated Pest Management (IPM) program that can include biological, cultural, 
and genetic practices aimed at preventing economic pest damage. IPM principles and practices include field scouting or 
other detection methods, correct target pest identification, population monitoring, and treating when target pest 
populations reach locally determined action thresholds. Consult your state cooperative extension service, professional 
consultants or other qualified authorities to determine appropriate action treatment threshold levels for treating specific 
pest/crop systems in your area.
• Rotate the use of this product with non-Group 2 or 5 herbicides.
• Avoid making more than two applications of CANSIO herbicide, and any other Group 2 or 5 herbicides within a 
single growing season unless mixed with an herbicide with a different site of action with an overlapping spectrum for 
the difficult-to- control weeds.
• Incorporate non-chemical weed control practices, such as mechanical cultivation, crop rotation, cover crops and weed- 
free crop seeds, as part of an integrated weed control program.
• Use good agronomic principles that enhance crop development and crop competitiveness.
• Thoroughly clean plant residues from equipment before leaving fields suspected to contain resistant weeds.
• Manage weeds in and around fields, during and after harvest to reduce weed seed production.
USE INFORMATION
MIXING: When using CANSIO herbicide, make sure the sprayer is completely clean and free of rust or corrosion 
which occurs from winter storage. Examine strainers and screens to be sure the sprayer is clean from previously used 
pesticides.
Any tank-mix containing CANSIO herbicide needs to be kept agitated and sprayed out immediately. DO NOT allow tank­
mixes to stand for prolonged periods of time.
The proper mixing procedures for CANSIO herbicide alone or in tank-mix combinations with other herbicides is:
1. Fill the spray tank 1/4 to 1/3 full with clean water.
2. Add specified rate of CANSIO herbicide while recirculating and with agitatorrunning.
3. Follow the triple rinse procedure described under “STORAGE AND DISPOSAL” to ensure that all product is removed 
from the container.
4. Add all other desired herbicides to tank and agitate thoroughly.
5. Mix thoroughly and add clean water to fill spray tank to desired level.
6. Continue agitation during application and until sprayer tank is empty.

6
Boom-less Ground Applications:
• Applicators are required to use a Medium or coarser droplet size (ASABE S572,1) for all applications.
• Do not apply when wind speeds exceed 10 miles per hour at the application site.
• Do not apply during temperature inversions.
are transitional soils and may be classified as medium textured soils in some regions of the U.S. 
CHEMIGATION;
DO NOT apply CANSIO herbicide through any type of irrigation system.
MANDATORY SPRAY DRIFT MANAGEMENT
Ground Boom Applications:
• Apply with the nozzle height recommended by the manufacturer, but no more than 3 feet above the ground or 
crop canopy.
• For applications prior to the emergence of crops and target weeds, applicators are required to use a Coarse or 
coarser droplet size (ASABE S572.1).
• For all other applications, applicators are required to use a Medium or coarser droplet size (ASABE S572.1).
• Do not apply when wind speeds exceed 10 miles per hour at the application site.
• Do not apply during temperature inversions.
Aerial Applications:
• Do not release spray at a height greater than 10 feet above the vegetative canopy, unless a greater application height 
is necessary for pilot safety.
• For applications prior to the emergence of crops and target weeds, applicators are required to use a Coarse or 
coarser droplet size (ASABE S572.1).
• For all other applications, apphcators are required to use a Medium or coarser droplet size (ASABES572.1).
• The boom length must not exceed 65% of the wingspan for airplanes or 75% of the rotor blade diameter forhelicopters.
• Applicators must use one-half swath displacement upwind at the downwind edge of the field.
• Nozzles must be oriented so the spray is directed toward the back of the aircraft.
• Do not apply when wind speeds exceed 10 miles per hour at the application site.
• Do not apply during temperature inversions.
SPRAY DRIFT MANAGEMENT ADVISORIES
THE APPLICATOR IS RESPONSIBLE FOR AVOIDING OFF-SITE SPRAY DRIFT.
BE AWARE OF NEARBY NON-TARGET SITES AND ENVIRONMENTAL CONDITIONS.
IMPORTANCE OF DROPLET SIZE
An effective way to reduce spray drift is to apply large droplets. Use the largest droplets that provide target pest control. 
While applying larger droplets will reduce spray drift, the potential for drift will be greater if applications are made 
improperly or under unfavorable environmental conditions.
Controlling Droplet Size — Ground Boom
• Volume - Increasing the spray volume so that larger droplets are produced will reduce spray drift. Use the highest 
practical spray volume for the application. If a greater spray volume is needed, consider using a nozzle with a higher 
flow rate.
• Pressure - Use the lowest spray pressure recommended for the nozzle to produce the target spray volume and droplet 
size.
• Spray Nozzle - Use a spray nozzle that is designed for the intended application. Consider using nozzles designed to 
reduce drift.
Controlling Droplet Size — Aircraft
• Adjust Nozzles - Follow nozzle manufacturers recommendations for setting up nozzles. Generally, to reduce fine 
droplets, nozzles should be oriented parallel with the airflow in flight.
BOOM HEIGHT - Ground Boom
Use the lowest boom height that is compatible with the spray nozzles that will provide uniform coverage. For ground 
equipment, the boom should remain level with the crop and have minimal bounce.

BOOM-LESS GROUND APPLICATIONS:
• Setting nozzles at the lowest effective height will help to reduce the potential for spray drift.
DRIFT CONTROL ADDITIVES
Using product compatible drift control additives can reduce drift potential. When a drift control additive is used, read and 
careftilly observe cautionary statements and all other information on the additive’s label. If using an additive that increases 
viscosity, ensure that the nozzles and other application equipment will function properly with a viscous spray solution.
Preferred drift control additives have been certified by the Council of Producers & Distributors of Agrotechnology 
(CPDA).
HANDHELD TECHNOLOGY APPLICATIONS: 
• Take precautions to minimize spray drift.
RELEASE HEIGHT - Aircraft
Higher release heights increase the potential for spray drift. When applying aerially to crops, do not release spray at a 
height greater than 10 ft above the crop canopy, unless a greater application height is necessary for pilot safety. 
SHIELDED SPRAYERS
Shielding the boom or individual nozzles can reduce spray drift. Consider using shielded sprayers. Verify that the shields 
are not interfering with the uniform deposition of the spray on the target area.
TEMPERATURE AND HUMIDITY
When making applications in hot and dry conditions, use larger droplets to reduce effects of evaporation.
TEMPERATURE INVERSIONS
Drift potential is high during a temperature inversion. Temperature inversions are characterized by increasing temperature 
with altitude and are common on nights with limited cloud cover and light to no wind. The presence of an inversion can be 
indicated by ground fog or by the movement of smoke from a ground source or an aircraft smoke generator. Smoke that 
layers and moves laterally in a concentrated cloud (under low wind conditions) indicates an inversion, while smoke that 
moves upward and rapidly dissipates indicates good vertical air mixing. Avoid applications during temperature inversions.
APPLICATION OF CANSIO HERBICIDE WITH HERBICIDE SPRAY EQUIPMENT
Use a standard low pressure (20 to 40 psi.) herbicide boom sprayer equipped with suitable nozzles and screens no finer 
than 50-mesh in nozzle and in-line strainers. Agitate thoroughly before and during application with bypass agitation. 
GROUND APPLICATION: Apply the proper rate of CANSIO herbicide in a minimum of 10 to 40 gallons of spray 
mixture per acre broadcast.
Banded Application; Use proportionally less CANSIO herbicide per acre in a band versus a broadcast application. For band 
application use 1/4 to 1 gallon of spray mix per inch of band width regardless of row spacing.
AERIAL APPLICATION: Where permitted, apply specified rate in a minimum of 2 to 10 gallons of spray mixture per 
acre.
Restriction: Aerial application is not permitted in the State of New York.
For All Applications of CANSIO herbicide; Sprayer must be accurately calibrated before applying CANSIO herbicide. 
Check sprayer during application to be sure it is working properly and delivering a uniform spray pattern. As the volume 
of spray mixture decreases per acre, the importance of accurate calibration and uniform application increases. Avoid other 
application, misapplication, and boom and spray swath overlapping that will increase spray dosage. (Crop injury may 
occur as a result). Avoid spray skips and gaps which allow weeds to grow in untreated soil.
SPRAYER CLEANUP; Spray equipment must be thoroughly cleaned to remove remaining traces of herbicide that might 
injure other crops to be sprayed. Drain any remaining spray solution of CANSIO herbicide from the spray tank and dispose 
of according to label disposal instructions. Rinse the spray tank and refill with water, adding a heavy-duty detergent at the 
rate of one cup per 20 gallons of water. Recycle this mixture through the equipment for 5 minutes and spray out. Repeat this 
procedure twice. Fill the spray tank with clean water, recycle for 5 minutes, and spray out. Clean pump and nozzle screens 
thoroughly. Wash away spray mixture from the outside of spray tank, nozzles or spray rig. All rinse water must be disposed 
of in compliance with local, state, and Federal guidelines.
APPLICATION OF CANSIO HERBICIDE IN FLUID FERTILIZERS
Crop injury may occur when CANSIO herbicide is applied in fluid fertilizer solutions. Follow the appropriate mixing 
procedures and compatibility check if you chose to apply CANSIO herbicide in fluid fertilizer solutions. When using tank­
mix combinations, be sure all components are compatible. Compatibility checks of CANSIO herbicide and tank-mix 
combinations which include CANSIO herbicide needs to be made for each batch of fluid fertilizer because of the 
variability of these fertilizers. It is the pesticide user’s responsibility to ensure that all products are registered for the 
intended use. Read and follow the applicable restrictions and limitations and directions for use on all product labels 
involved in tank mixing. Users must follow the most restrictive directions for use and precautionary statements of each 
product in the tank mixture. If the instructions on the tank mix partner label conflict with this CANSIO herbicide label, DO
7

8
RESTRICTIONS - BARLEY AND WHEAT:
Do not exceed rates specified on this label.
NOT use in a tank mixture with CANSIO herbicide.
Compatibility Check:
1. Pre-mix 2 teaspoons of CANSIO herbicide with 8 teaspoons of water (1:4 ratio) in a quart jar by adding the water 
first and follow with CANSIO herbicide. Mix thoroughly, if a second herbicide is to be used, double the amount of 
water (1:8 ratio) and add the second herbicide after mixing CANSIO herbicide first.
2. Then pour 1 pint of fluid fertilizer into the quart jar and shake well.
3. Allow to stand for 5 minutes.
THIS COMPATIBILITY CHECK MUST ONLY BE USED WHEN MIXING WITH FLUID FERTILIZERS. 
Interpretation of Results: If the solution in the jar appears to be uniform, without signs of agglomeration, or without a 
separation of an oily film on top of the fertilizer, the mixture may be used. If not, repeat the compatibility check using twice 
the amount of water or add a compatibility agent to the water. If separation occurs, but the mixture can be resuspended by 
shaking, then application is possible with good agitation in the spray tank.
Tank-mixing Guidelines:
1. Add the required amount of water and compatibility agent (if required) to the tank. Start agitation while adding 
CANSIO herbicide and follow by adding the fluid fertilizer and agitate.
2. If a second herbicide is to be used, follow as above in 1, but use twice the amount of water. Start agitation and add 
CANSIO herbicide and follow by adding the second herbicide, and then continue filling the tank with fluid 
fertilizer.
3. Maintain continuous agitation to ensure uniform spray mixture until the tank is emptied.
SPRING AND WINTER BARLEY AND WINTER WHEAT
CANSIO herbicide may be used for control or suppression of certain grasses and broadleaf weeds when applied 
postemergence to spring and winter barley or winter wheat at initial tillering to just before jointing. CANSIO herbicide 
may be used alone or in a tank-mixture in the following states: AR, DE, GA, ID, IL, IN, KS, KY,LA, MD, MS, MO, MT, 
NC, NV, OH, OK, OR, PA, SC, TN, TX, UT, VA, and WA.
Mixing: See the “Use Information” section of this label for specific mixing procedures. When tank-mixing, carefully 
follow the instructions on this label. Refer to the other product labels registered for use in barley and winter wheat for 
additional use directions, rates, weeds controlled and restrictions. It is the pesticide user’s responsibility to ensure that 
all products are registered for the intended use. Read and follow the applicable restrictions and limitations and 
directions for use on all product labels involved in tank mixing. Users must follow the most restrictive directions for 
use and precautionary statements of each product in the tank mixture. If the instructions on the tank mix partner label 
conflict with this CANSIO herbicide label, DO NOT use in a tank mixture with CANSIO herbicide.
Application: CANSIO herbicide may be applied by aerial (except in the state of New York), or ground application 
equipment. Use a minimum spray volume of 2 gpa by air and 10 gpa by ground. Uniform spray coverage is necessary to 
obtain optimum weed control and to minimize potential for crop injury. Apply CANSIO herbicide when the crop is healthy 
and actively growing.
On irrigated barley and wheat, apply 0.5 inch or less of water for the first irrigation, the maximum amount for each 
additional irrigation must not exceed 1 inch. Allow a minimum of 14 days between the first irrigation and subsequent 
inigations.
Performance Factors: Weed control may not be observed for 2 to 4 weeks under normal growth conditions and for 4 to 6 
weeks under very dry conditions. Moisture (at least 1/2 inch) is required within 2 to 3 weeks after application to move 
CANSIO herbicide into the weed root zone. Lack of adequate moisture after application may result in poor or erratic weed 
control. Control or suppression of listed weeds is dependent on weed size at time of application. Control or suppression 
may be reduced if broadleaf weeds are taller than 1 inch or grasses have more than 2 leaves.
Tank-mixtures: CANSIO herbicide may be tank-mixed with full or reduced rates of other herbicide, insecticide, and 
fungicide products registered for use in the specified crops. Consult tank mix partner labeling for rate and crop rotation 
restrictions. It is the pesticide user’s responsibility to ensure that all products are registered for the intended use. Read and 
follow the applicable restrictions and limitations and directions for use on all product labels involved in tank mixing. 
Users must follow the most restrictive directions for use and precautionary statements of each product in the tank mixture. 
If the instructions on the tank mix partner label conflicts with this CANSIO herbicide label, DO NOT use in a tank 
mixture with CANSIO herbicide. Ensure the tank mix product is labeled for the same timing, method of application, 
adjuvants, and use restrictions as CANSIO herbicide, as well as other products used in the tank mixture.
Weed control and crop safety resulting from the use of tank mixtures not specifically noted on this label, or in separately 
published FMC information, are the responsibility of the user. For tank-mix combinations, follow the most restrictive label.

9
Do not apply CANSIO herbicide through any type of irrigation equipment.
Do not use on spring wheat and Durum wheat varieties.
Do not plant spring seeded cereals following fall fallow applications of CANSIO herbicide.
Do not apply CANSIO herbicide in the spring where CANSIO herbicide was applied in the fall.
Do not use on soils containing less than 0.75% organic matter.
Do not apply more than a 4.2 ounces per acre per single application of CANSIO herbicide (0.1688 lb, metribuzin, 0.0186 lb. 
thifensulfuron-methyl, 0.0095 lb. tribenuron-methyl per acre), review use direction for crop growth stage, soil texture and 
soil organic matter for appropriate rate.
Do not apply more than a total of 4.2 ounces per acre per year of CANSIO herbicide (0.1688 lb. metribuzin,
0.0186 lb. thifensulfuron-methyl, 0.0095 lb. tnbenuron-methyl per acre per year).
Do not apply CANSIO herbicide on barley and wheat more than one time per year.
Do not graze wheat within 14 days of CANSIO herbicide application.
Do not graze or harvest barley before crop maturity.
Pre-harvest Interval (PHI): Do not harvest sooner than 45 days after the last application of CANSIO herbicide. 
Do not graze fallow treated fields.
Do not apply to wheat and barley underseeded with another crop.
WHEAT AND BARLEY VARIETAL SENSITIVITY
Wheat and barley varieties vary in their sensitivity to CANSIO herbicide. To avoid possible crop injury, contact the seed 
supplier or herbicide expert for a variety direction prior to treatment or treat a small strip of the unlisted variety with the 
labeled CANSIO herbicide rate to ascertain crop sensitivity before treating an entire field.
Spring and Winter Barley and Winter Wheat Rotations Following Potatoes Treated with Metribuzin: If planting a 
sensitive variety, following potatoes treated with metribuzin containing products, refer to the potato section of the 
metribuzin label for special cultural practices to follow.
PRECAUTIONS - BARLEY AND WHEAT:
Crop injury may occur if CANSIO herbicide is applied:
1 When the crop is under stress including winter kill, frost damage, prolonged cold weather, wide fluctuations in day/night 
temperatures, disease, insect damage, drought or excessive moisture, severe grazing, low fertility or when these 
conditions follow the application.
2. In combination with fluid fertilizer especially with the addition ofsurfactant.
3. Prior to the growth stage specified on this label.
4. To soils high in lime or sodium, a pH greater than 7.7, calcareous, gravelly, thinly covered or exposed subsoil areas.
5. To fields where seeds have been planted less than 1 inch deep.
6. To a non-winter hardy wheat or barley variety.
7. To a sensitive wheat or barley variety.
8. To frozen soil or crop still in winter dormancy.

APPLICATION DIRECTIONS:
POSTEMERGENCE BROADCAST APPLICATIONS OF CANSIO HERBICIDE
Coarse
3.5 3.5 to 4.2
3.5 to 4.2
3.5 to 4.2
CANSIO herbicide
Use Rate Active Ingredient Equivalent
Use Rate Active Ingredient Equivalent
10
3 Tillers to Just 
Before Jointing
Do not apply more than a 4.2 ounces per acre per single application of CANSIO herbicide (0.1688 lb. metribuzin,
0.0186 lb. thifensulfuron-methyl, 0.0095 lb. tribenuron-methyl per acre).
Do not apply more than a total of 4.2 ounces per acre per year of CANSIO herbicide (0.1688 lb. metribuzin,
0.0186 lb. thifensulfuron-methyl, 0.0095 lb. tribenuron-methyl per acre).
Do not apply CANSIO herbicide on fallow more than one time per year.
SOIL
TEXTURE
Apply 2.3 - 4.2 oz CANSIO™ herbicide per acre 
as a bumdown treatment.
CANSIO herbicide alone or in a tank-mix with labeled broadleaf herbicides may be applied by aerial or ground spray 
equipment as a broadcast postemergence spray.
Apply 2.3 - 4.2 oz CANSIO™ herbicide per acre 
to fallow.
Metribuzin
(Lb. ai/A)
0.0924
0.1407 
0.1688
Active Ingredient Equivalent 
Thifensulfuron-methyl 
(Lb. ai/A)_________________
______0.0102_____________ 
_____ 0.0155_____________ 
0.0186
Metribuzin
(Lb. ai/A)
0.0924 
to 
0.1688
Metribuzin
(Lb. ai/A)
0.0924 
to 
0.1688
3.5
3.5
Thifensulfuron-methyl
(Lb. ai/A) 
0.0102 
to 
0.0186
Thifensulfuron-methyl 
(Lb. ai/A) 
0.0102 
to 
0.0186
Tribenuron-methyl 
(Lb. ai/A)
0.0052
0.0079 
0.0095
3.5
3.5
T ribenuron-methyl 
(Lb. ai/A)
0.0052 
to 
0.0095
CANSIO herbicide may be applied in combination with other suitable registered fallow herbicides including products with 
the active ingredients 2,4-D (LVE), chlorimuron ethyl, glufosinate, glyphosate, rimsulfuron, saflufenacil, thifensulfuron- 
methyl, tribenuron-methyl, dicamba, paraquat, or for control of emerged weeds. Observe all precautions and limitations on 
the labeling of all products used in tank-mixtures.
RESTRICTIONS - FALLOW
3.5 to 4.2
3.5 to 4.2
DO NOT apply within 2 weeks after grazing or breaking of winter dormancy. Apply after 
the crop is at or beyond the 3-tiller growth stage but before jointing. Secondary roots need 
to be developed and larger than 1 inch long. DO NOT apply before 75 days after planting. 
For dryland winter wheat (non-irrigated), apply the highest specified rate to achieve 
maximum weed suppression/control.
GEORGIA ONLY: Wheat must be planted before November 15 in the Piedmont area and 
Northern part of the state, and before December 1 in the Coastal Plain area.
FALLOW
CANSIO herbicide may be used as a fallow treatment, in the spring through the fall when the majority of weeds have 
emerged and are actively growing.
PRE-PLANT BURNDOWN
CANSIO herbicide can be used as a bumdown treatment prior to planting soybeans or com. See “ROTATIONAL 
CROP GUIDELINES” for the minimum time interval required before planting other crops.
CROP GROWTH 
STAGE _________
Initial Tillering
to 2 Tillers
Rate
(Oz/A)
2.3
3.5
4.2
Medium
Fine
Use these rates on crops with secondary roots smaller than 1 inch.
For dryland winter wheat (non-irrigated), apply the highest specified rate to achieve 
maximum weed control
Coarse
Medium
Fine
CANSIO 
herbicide
Rate 
(Oz/A)
2.3 
to 
4.2
CANSIO 
herbicide
Rate 
(Oz/A)
2.3 
to 
4.2
Tribenuron-methyl (Lb.
________ai/A)________ 
0.0052
to 
0.0095
CANSIO HERBICIDE (Oz/A)
0.75 to 2.0 % Organic Matter
2.3
Over 2.0 % Organic Matter
3.5

11
Apply only by ground equipment. CANSIO herbicide may be applied in combination with other suitable registered 
bumdown herbicides including products containing the active ingredients 2,4-D (LVE), chlorimuron ethyl, dicamba, 
glufosinate, glyphosate, paraquat, rimsulfuron, saflufenacil, thifensulfuron-methyl, or tribenuron-methyl for control of 
emerged weeds. Observe all precautions and limitations on the labeling of all products used in tank-mixtures. It is the 
pesticide user’s responsibility to ensure that all products are registered for the intended use. Read and follow the 
applicable restrictions and limitations and directions for use on all product labels involved in tank mixing. Users must 
follow the most restrictive directions for use and precautionary statements of each product in the tank mixture. If the 
instructions on the tank mix partner label conflict with this CANSIO herbicide label, DO NOT use in a tank mixture with 
CANSIO herbicide.
CANSIO herbicide bumdown can be applied before planting in the following areas:
Field Corn; Illinois, Indiana, Iowa, Kansas, Kentucky, Michigan, Minnesota, Missouri, Nebraska, Ohio, South Dakota, and 
Wisconsin.
Soybeans: All areas
RESTRICTIONS - BURNDOWN:
• Do not apply these treatments after crop emergence. Observe all precautions and restrictions on the labeling of all 
products used in tank mixtures. Follow the most restrictive directions.
• Do not apply more than a 4.2 ounces per acre per single application of CANSIO herbicide (0.1688 lb. metribuzin,
0.0186 lb. thifensulfuron-methyl, 0.0095 lb. tribenuron-methyl per acre).
• Do not apply more than a total of 4.2 ounces per acre per year of CANSIO herbicide (0.1688 lb. metribuzin, 0.0186 lb. 
thifensulfuron-methyl, 0.0095 lb. tribenuron-methyl per acre per year).
• Do not apply CANSIO herbicide for bumdown more than one time per year
Field Corn
1. Do not apply on coarse textured soils with less than 1.5% organic matter.
2 Do not apply on soils having pH 7.0 or greater.
3. Com seed needs to be planted a minimum of 1.5 inches deep.
4. CANSIO herbicide may only be used in hybrid seed com production fields if both inbred parents are known to be 
tolerant to metribuzin.
5. Do not apply more than 4.0 oz ai (0.25 lb. ai/A) of metribuzin for bumdown before com per acre per year. 
Soybeans:
1. If tank mixing with 2,4-D, apply only 2,4-D low volatile ester formulations which are registered and specified for 
preplant or bumdown use in soybeans.
2. Do not apply tank mixtures containing 2,4-D LVE if wind is blowing toward desired susceptible plants (i.e. cotton, 
tobacco, tomato, etc.) or when wind speeds exceed 6 miles per hour.
Feeding and Harvest:
Pre-harvest Interval (PHI): Com treated with CANSIO herbicide may be harvested for silage or grain 60 days after 
treatment. Soybean vines or hay treated with CANSIO herbicide may be grazed or fed to livestock 40 days after 
application.
Follow the most restrictive preharvest interval of all products used in a tank-mixture.
SPRAY ADJUVANTS
Always include a spray adjuvant with applications of CANSIO herbicide when used for fallow or bumdown 
applications. In addition to a spray adjuvant, an ammonium nitrogen fertilizer may be used.
Consult your Ag dealer or applicator, local FMC fact sheets, technical bulletins, and service policies prior to using an 
adjuvant system. If another herbicide is tank mixed with CANSIO herbicide, select adjuvants authorized for use with 
both products.
Nonionic Surfactant (NIS)
Apply 0.06 to 0.50% volume/volume (1/2 pt to 4 pt per 100 gal of spray solution).
Surfactant products must contain at least 60% nonionic surfactant with a hydrophilic/lipophilic balance (HLB) greater than 
12.
Petroleum Crop Oil Concentrate (COC) or Modified Seed Oil (MSO)
Apply at 1% volume/volume (1 gal per 100 gal spray solution) or 2% volume/volume under and conditions.
Oil adjuvants must contain at least 80% high quality, petroleum (mineral) or modified vegetable seed oil with at least 15% 
surfactant emulsifiers.

*
Blue/Purple mustard Corncockle Tansymustard
Spring (Vernal) whitlowgrassButtercup, spp
*
4.2 0.1688
12
Common ragweed, Lanceleaf sage: In wheat and barley apply
CANSIO herbicide at 3.5 ounces per acre in combination with 2, 4- 
D (ester formulations work best) when weeds are small and actively 
growing. When using 2, 4-D, be sure to add surfactant at the rate of
* See SPECIFIC WEED INSTRUCTIONS for more information.
f Naturally occurring Sulfonylurea (Group 2) resistant biotypes are known to occur.
CANSIO
herbicide
CANSIO
herbicide
Metribuziii
(Lb. ai/A)
Canada thistle* 
Catchweed bedstraw
Common sunflower f
Conical (Sand) catchfly
Com chamomile______
Com gromwell*_______
Com spurry
Cheat
Dandelion*
Vetch* (common, hairy) 
Wild oat
Windgrass
Winter vetch
Tarweed fiddleneck_____
Tumble/ Jim Hill mustard
Slimleaf lambsquarters 
Smallflower buttercup
Smallseed falseflax f
Stinking chickweed
Swinecress
Tribenuron- 
methyl 
(Lb. ai/A) 
0.0095
Tribenuron- 
methyl 
(Lb. ai/A)
0.0079
Broadleaf dock_________
Bur buttercup
Bushy wallflower/Treacle 
mustard f______________
Carolina gromwell, spp 
Catchweed (Madwort) 
Clasping pepperweed 
Coast fiddleneck 
Common buckwheat
Common duckweed *f 
Common cocklebur 
Common groundsel 
Common lambsquarters f 
Common radish 
Common ragweed *f
Kochia *t
Ladysthumb 
Lanceleaf sage
London rocket 
Marshelder f
Mayweed chamomile/Stinking
mayweed/dog fennel
(Anthemis cotula L.) f_______
Miners lettuce_______________
Mousear chickweed
Metribuziii
(Lb. ai/A)
0.1407
Ammonium Nitrogen Fertilizer
Use 2 qt/acre of a high-quality urea ammonium nitrate (UAN), including 28%N or 32%N, or 2 Ib/acre of a 
spraygrade ammonium sulfate (AMS). Use 4 qt/acre UAN or 4 Ib/acre AMS under arid conditions. See 
"APPLICATION OF CANSIO herbicide IN FLUID FERTILIZERS" for instructions on using fertilizer as a carrier 
in place of water.
Special Adjuvant Types
Combination adjuvant products may be used at doses that provide the required amount of NIS, COC, MSO and/or 
ammonium nitrogen fertilizer. Consult product literature for use rates mid restrictions.
WEEDS CONTROLLED
Used at specified rates, CANSIO herbicide will control many annual broadleaf weeds. Control is best when applied 
to young, actively growing weeds. Weeds controlled by CANSIO herbicide include:_______________________________
Annual knawel
Annual polemonium 
Annual sowthistle
Bittercress_________
Black mustard
Nightflowering catchfly
Pennsylvania smartweed 
Pigweed, spp.__________
Pineappleweed_________
Prickly lettuce * j_______
Prostrate knotweed 
Redmaids_____________
Redroot pigweed f_____
Russian thistle *t______
Scentless______________
Chamomile/mayweed 
Sheperdspurse
Cress (mouse-ear)______
Curly dock
Cutleaf evening primrose
False chamomile_______
Field chickweed________
Field peimycress________
Filaree (redstem, Texas) 
Flixweed______________
Geranium 
Green smartweed_______
Hempnettle____________
Henbit_________________
Jacob’s Ladder_________
Ivyleaf speedwell
WEEDS SUPPRESSED 
Annual bluegrass________
Blackgrass
Bulbous bluegrass
Active Ingredient Equivalent 
Ibifensulfuron- 
methyl 
(Lb. ai/A)
0.0155
Rate
(Oz/A)
See SPECIFIC WEED INSTRUCTIONS for more information.
* * Suppression: A visual reduction of weed population as well as a significant loss of vigor. For better results, use the highest 
specified rate of CANSIO herbicide per acre. For broadleaf weeds include a tank mix partner including active ingredients 
including 2,4-D, MCPA, bromoxynil or dicamba.
SPECinC WEED INSTRUCTIONS____________________________
Canada thistle: For control in wheat and barley, apply 4.2 ounces
of CANSIO herbicide per acre plus surfactant when all thistles are
4” to 8” with 2” to 6” of new growth. Make the application in the
spring. Control will be improved by using CANSIO herbicide in 
combination with 2,4-D.
Common chickweed (including ALS resistant): Control is best when common chickweed is 3 inches tall or less.
Active Ingredient Equivalent 
Ihifensulfuron- 
methyl 
(Lb. ai/A) 
0.0186
Downy brome
Foxtail, spp. Hare (Wild) 
barley_________________
Japanese brome________
Mallow (common, little)
Rate
(Oz/A) 
L5~
Nightshade (cutleaf, hairy)
Rescuegrass
Ripgut brome
Virginia pepperweed
Volunteer lentils 
Volunteer peas_____
Volunteer sunflower 
Wild buckwheat*
Wild chamomile 
Wild garhc*_______
Wild mustardf_____
Wild radish*
Wild turnip

2.3 0.0924 0.0102 0.0052
*
Cover crops for soil building or erosion control may be planted anytime but DO NOT graze or harvest for food or feed.
t
13
0.1407
to
0.1688
0.1407
to
0.1688
0.0155 
to
0.0186
0.0155
to
0.0186
0.0079
to
0.0095
0.0079
to
0.0095
1/4 to 1/2 quart per 100 gallons of spray solution (0.06 to 0.125% 
v/v—use the higher rate under stress conditions).
CANSIO
herbicide
CANSIO
herbicide
CANSIO 
herbicide
3.5
to
4.2
3.5
to
4.2
Metribuzin 
(Lb. ai/A)
Metribuzin 
(Lb. ai/A)
Tribenuron- 
methyl 
(Lb. ai/A)
Tribennron- 
methyl 
(Lb. ai/A)
14 days______
Field Com***
18 months_________________________
Onions____________________________
Sugar beets________________________
Oher root crops not listed on this label 
All other crops not listed on this label
Tribenuron- 
methyl 
(Lb. ai/A)
0.0079 
to
0.0095
Metribuzin
(Lb. ai/A)
0.1407 
to 
0.1688
Wild radish: For best results in wheat and barley, apply 3.5 to 4.2
ounces CANSIO herbicide per acre plus surfactant either in the fall or 
spring to wild radish rosettes less than 6 inches in diameter.
Applications made later than 30 days after weed emergence will result 
in partial control. For increased control of severe wild radish
infestations, or wild radish emerged greater than 30 days, apply
CANSIO herbicide at 2.3 ounces per acre in combination with MCPA.
Surfactant is required when tank mixing with MCPA, add 1 quart per
100 gallons of spray solution (0.25% vol/vol). Fall applications needs 
to be made prior to hardening off of plants.
ROTATIONAL CROP GUIDELINES
The following table shows minimum recropping intervals following CANSIO herbicide application:
* Cover crops for soil building or erosion control may be planted anytime but DO NOT graze or harvest for food or feed. 
Stand reduction may occur in some areas.
** Following peas, lentils orsoybeans.
*** Where CANSIO™ is used on light textured soils (including sands and loamy sands) or on high pH soils (>7.9), extend time to 
planting by 7 additional days.
DO NOT rotate rice after any application to a primary crop greater than 1.0 pounds of active ingredient per acre of metribuzin 
per year.
Rate
(Oz/A)
Rate
(Oz/A)
Active Ingredient Equivalent
Tbifensulfuron- 
raethyl 
(Lb. ai/A)
0.0155 
to 
0.0186
Active Ingredient Equivalent 
Ihifensulfuron- 
raethyl 
(Lb. ai/A)
Active Ingredient Equivalent 
Ihifensulfuron- 
raethyl 
(Lb. ai/A)
8 months 
Barley
Lentils 
Peas 
Wheat
12 months
Potatoes
Ricef
4 months
Alfalfa 
Asparagus
Barley**
Forage grasses 
Sainfoin_____
Sugarcane
Tomatoes
Wheat**
Rate
(Oz/A) 
L5~ 
to 
4.2
7 days______
Soybeans***
Corn gromwell, Wild buckwheat: For control in wheat and barley, use
3.5 to 4.2 ounces CANSIO herbicide per acre plus surfactant.
Dandelion: For best results, apply 3.5 to 4.2 ounces CANSIO
herbicide per acre plus surfactant before flowering. The addition of
2,4-D or MCPA may improve control of heavy populations, stressed 
weeds, and larger weeds.
Kochia, Russian thistle, Prickly lettuce: Naturally occurring SU resistant biotypes of these weeds are known to occur. 
For best results, use CANSIO herbicide in a tank mix with registered for this use containing the active ingredients 
including dicamba and 2,4-D; or bromoxynil and 2,4-D. CANSIO herbicide needs to be applied in the spring when weeds 
are less than 2” tall or 2” across and are actively growing.
Vetch (common and hairy): For control in wheat and barley, use 3.5
to 4.2 oimces of CANSIO herbicide per acre plus surfactant when vetch 
is less than 6” in length. For severe infestations of vetch, or when vetch 
is greater than 6” in length, use CANSIO herbicide in combination with
2,4-D or MCPA.
Wild garlic: CANSIO herbicide may provide reduced control of wild 
garlic as compared to HARMONY® EXTRA. For best control in 
wheat and barley, use 3.5 to 4.2 ounces CANSIO herbicide per acre 
plus surfactant when wild garlic plants are less than 12” tall with 2” to
4” of new growth. Plants hardened-off by cold weather and/or drought 
stress may be more difficult to control.
Thorough spray coverage of all garlic plants is essential. Typical
symptoms of dying garlic plants may not be noticeable for 2 to 5 
weeks.

14
STORAGE AND DISPOSAL
Pesticide Storage: Store product in original container only. Do not contaminate water, other pesticides, fertilizer, food 
or feed in storage. Store in a cool, dry place.
Pesticide Disposal: Do not contaminate water, food, or feed by disposal. Waste resulting from the use of this product 
must be disposed of on site or at an approved waste disposal facility.
Container Handling: Refer to the Net Contents section of this product’s labeling for the applicable ‘Nonrefillable 
Container” or “Refillable Container” designation.
Nonrefillable Plastic and Metal Containers (Capacity Equal to or Less Than 50 Pounds): Nonrefillable container. Do 
not reuse or refill this container. Triple rinse container (or equivalent) promptly after emptying. Triple rinse asfollows: 
Empty the remaining contents into application equipment or a mix tank. Fill the container 1/4 full with water and 
recap. Shake for 10 seconds. Pour rinsate into application equipment or a mix tank or store rinsate for later use or 
disposal. Drain for 10 seconds after the flow begins to drip. Repeat this procedure two more times. Then, for Plastic 
Containers, offer for recycling if available or puncture and dispose of in a sanitary landfill, or by incineration. Do not 
bum, unless allowed by state and local ordinances. For Metal Containers, offer for recycling if available or 
reconditioning if appropriate, or puncture and dispose of in a sanitary landfill, or by other procedures approved by 
state and local authorities.
Nonrefillable Plastic and Metal Containers (Capacity Greater Than 50 Pounds): Nonrefillable container. Do not reuse 
or refill this container. Triple rinse container (or equivalent) promptly after emptying. Triple rinse as follows: Empty 
the remaining contents into application equipment or a mix tank Fill the container 1/4 full with water. 
Replace and tighten closures. Tip container on its side and roll it back and forth, ensuring at least one complete 
revolution, for 30 seconds. Stand the container on its end and tip it back and forth several times. Turn the container 
over onto its other end and tip it back and forth several times. Empty the rinsate into application equipment or a mix 
tank or store rinsate for later use or disposal. Repeat this procedure two more times. Then, for Plastic Containers, offer 
for recycling if available or puncture and dispose of in a sanitary landfill, or by incineration. Do not bum, unless 
allowed by state and local ordinances. For Metal Containers, offer for recycling if available or reconditioning if 
appropriate, or puncture and dispose of in a sanitary landfill, or by other procedures approved by state and local 
authorities.
Nonrefillable Plastic and Metal Containers, e.g.. Intermediate Bulk Containers [IBC] (Size or Shape Too Large to be 
Tipped, Rolled or Turned Upside Down): Nonrefillable container. Do not reuse or refill this container. Clean container 
promptly after emptying the contents from this container into application equipment or mix tank and before final 
disposal using the following pressure rinsing procedure. Insert a lance fitted with a suitable tank cleaning nozzle into 
the container and ensure that the water spray thoroughly covers the top, bottom and all sides inside the container. The 
nozzle manufacturer generally provides mstructions for the appropriate spray pressure, spray duration and/or spray 
volume. If the manufacturer’s instructions are not available, pressure rinse the container for at least 60 seconds using a 
minimum pressure of 30 PSI with a minimum rinse volume of 10% of the container volume. Drain, pour or pump 
rinsate into application equipment or rinsate collection system. Repeat this pressure rinsing procedure two more times. 
Then, for Plastic Containers, offer for recycling if available or puncture and dispose of in a sanitary landfill, or by 
incineration. For Metal Containers, offer for recycling if available or reconditioning if appropriate, or puncture and 
dispose of in a sanitary landfill, or by other procedures approved by state and local authorities.
Nonrefillable Paper or Plastic Bags, Fiber Sacks including Flexible Intermediate Bulk Containers (FIBC) or Fiber 
Drums With Liners: Nonrefillable container. Do not reuse or refill this container. Completely empty paper or plastic 
bag, fiber sack or drum liner by shaking and tapping sides and bottom to loosen clinging particles. Empty residue into 
application or manufacturing equipment. Then offer for recycling if available or dispose of empty paper or plastic bag, 
fiber sack or fiber drum and liner in a sanitary landfill, or by incineration. Do not bum, unless allowed by state and 
local ordinances.
Refillable Fiber Drums With Liners: Refillable container (fiber drum only). Refilling Fiber Drum: Refill this fiber 
drum with CANSIO herbicide containing thifensulfuron methyl, tribenuron methyl, and metribuzin only. Do not 
reuse this fiber drum for any other purpose. Cleaning before refilling is the responsibility of the refiller. Completely 
empty liner by shaking and tapping sides and bottom to loosen clinging particles. Empty residue into application or 
manufacturing equipment. Disposing of Fiber Drum and/or Liner: Do not reuse this fiber drum for any other purpose 
other than refilling (see preceding). Cleaning the container (liner and/or fiber drum) before final disposal is the 
responsibility of the person disposing of the container. Offer the liner for recycling if available or dispose of liner in a 
sanitary landfill, or by incineration. Do not bum, unless allowed by state and local ordinances. If drum is 
contaminated and cannot be reused, dispose of it in the manner required for its liner. To clean the fiber drum before 
final disposal, completely empty the fiber drum by shaking and tapping sides and bottom to loosen clinging particles. 
Empty residue into application or manufacturing equipment. Then offer the fiber drum for recycling if available or 
dispose of in a sanitary landfill, or by incineration. Do not bum, unless allowed by state and local ordinances.

D-4040 050319
14
NOTICE TO BUYER: Purchase of this material does not confer any rights under patents of countries outside of the 
United States.
FMC and CANSIO are trademarks of FMC Corporation or an affiliate.
All Other Refillable Containers; Refillable container. Refilling Container: Refill this container with CANSIO 
herbicide containing thifensulfuron methyl, tribenuron methyl, and metribuzin only. Do not reuse this container for 
any other purpose. Cleaning before refilling is the responsibility of the refiller. Prior to refilling, inspect carefully for 
damage such as cracks, punctures, abrasions, worn out threads and closure devices. If damage is found, do not use the 
container, contact FMC at the number below for instructions. Check for leaks after refilling and before transporting. If 
leaks are found, do not reuse or transport container, contact FMC at the number below for instructions. Disposing of 
Container; Do not reuse this container for any other purpose other than refilling (see preceding). Cleaning the 
container before final disposal is the responsibility of the person disposing of the container. To clean the container 
before final disposal, use the following pressure rinsing procedure. Insert a lance fitted with a suitable tank cleaning 
nozzle into the container and ensure that the water spray thoroughly covers the top, bottom and all sides inside the 
container. The nozzle manufacturer generally provides instructions for the appropriate spray pressure, spray duration 
and/or spray volume. If the manufacturer’s instructions are not available, pressure rinse the container for at least 60 
seconds using a minimum pressure of 30 PSI with a minimum rinse volume of 10% of the container volume. Drain, 
pour or pump rinsate into application equipment or rinsate collection system. Repeat this pressure rinsing procedure 
two more times. Then, for Plastic Containers, offer for recycling if available or puncture and dispose of in a sanitary 
landfill, or by incineration. Do not bum, unless allowed by state and local ordinances. For Metal Containers, offer for 
recycling if available or reconditioning if appropriate, or puncture and dispose of in a sanitary landfill, or by other 
procedures approved by state and local authorities.
Outer Foil Pouches of Water Soluble Packets (WSP); Nonrefillable container. Do not reuse or refill this container. 
Offer for recycling if available or, dispose of the empty outer foil pouch in the trash as long as WSP is unbroken. If the 
outer pouch contacts the formulated product in any way, the pouch must be triple rinsed with clean water. Add the 
rinsate to the spray tank and dispose of the outer pouch as described previously.
Do not transport if this container is damaged or leaking. If the container is damaged, leaking or obsolete, or in the 
event of a major spill, fire or other emergency, contact CHEMTREC (Transportation and Spills) at 1-800-424-9300, 
day or night.

CONDITIONS OF SALE AND LIMITATION OF WARRANTY AND LIABILITY
This Condition of Sale and Limitation of Warranty and Liability may not be amended by any oral or written agreement.
15
FMC Corporation, 2929 Walnut Street, Philadelphia, PA 19104 
© 1998-2019 FMC Corporation. All rights reserved.
Notice: Read the entire Directions for Use and Conditions of Sale and Limitation of Warranty and Liability before buying or 
using this product. If the terms are not acceptable, return the product at once, unopened, and the purchase price will be refunded.
The Directions for Use of this product must be followed carefully. It is impossible to eliminate all risks inherently associated with 
the use of this product. Crop injury, ineffectiveness, or other unintended consequences may result because of such factors as 
manner of use or application, weather or crop conditions beyond the control of FMC or Seller. To the extent consistent with 
applicable law, all such risks shall be assumed by Buyer and User, and, to the extent consistent with applicable law. Buyer and 
User agree to hold FMC and Seller harmless for any claims relating to such factors.
Seller warrants that this product conforms to the chemical description on the label and is reasonably fit for the purposes 
stated on the Directions for Use when used in accordance with the directions under normal conditions of use. TO THE 
EXTENT CONSISTENT WITH APPLICABLE LAW, FMC MAKES NO WARRANTIES OF MERCHANTABILITY 
OR OF FITNESS FOR A PARTICULAR PURPOSE, NOR ANY OTHER EXPRESS OR IMPLIED WARRANTIES 
WITH RESPECT TO THE SELECTION, PURCHASE, OR USE OF THIS PRODUCT. Any warranties, express or 
implied, having been made are inapplicable if this product has been used contrary to label instructions, or under 
abnormal conditions, or under conditions not reasonably foreseeable to (or beyond the control of) Seller or FMC, and, to 
the extent permitted by applicable law. Buyer assumes the risk of any such use.
To the extent consistent with applicable law, FMC or Seller shall not be liable for any incidental, consequential or special 
damages resulting from the use or handling of this product. TO THE EXTENT CONSISTENT WITH APPLICABLE LAW, 
THE EXCLUSIVE REMEDY OF THE USER OR BUYER, AND THE EXCLUSIVE LIABILITY OF FMC AND SELLER 
FOR ANY AND ALL CLAIMS, LOSSES, INJURIES OR DAMAGES (INCLUDING CLAIMS BASED ON BREACH OF 
WARRANTY, CONTRACT, NEGLIGENCE, TORT, STRICT LIABILITY OR OTHERWISE) RESULTING FROM THE USE 
OR HANDLING OF THIS PRODUCT, SHALL BE THE RETURN OF THE PURCHASE PRICE OF THE PRODUCT OR, AT 
THE ELECTION OF FMC OR SELLER, THE REPLACEMENT OF THE PRODUCT.