# F9651-2 Fungicide

- EPA Reg No: **279-3605**
- Registrant: FMC CORPORATION 
- Signal word: Caution
- Active ingredients: Bixafen (14.03%); Tebuconazole (29.83%)
- Label accepted: 2018-12-06
- Source PDF: https://www3.epa.gov/pesticides/chem_search/ppls/000279-03605-20181206.pdf

---
Registration Notice Unconditional v.20150320 
 
 
 
 
U.S. ENVIRONMENTAL PROTECTION AGENCY 
Office of Pesticide Programs 
Registration Division (7505P) 
1200 Pennsylvania Ave., N.W. 
Washington, D.C. 20460 
 
EPA Reg. Number: 
 
279-3605 
 
Date of Issuance: 
 
12/6/18 
NOTICE OF PESTICIDE: 
 X Registration 
 Reregistration 
 
Term of Issuance: 
Unconditional 
 (under FIFRA, as amended) 
Name of Pesticide Product: 
F9651-2 Fungicide 
 
Name and Address of Registrant (include ZIP Code): 
Callista O. Chukwunenye, Ph.D. 
Manager Sr., Product Registrations 
FMC Corporation 
2929 Walnut Street 
Philadelphia, PA 19104 
 
Note: Changes in labeling differing in substance from that accepted in connection with this registration must be submitted to and accepted by the 
Registration Division prior to use of the label in commerce. In any correspondence on this product always refer to the above EPA registration number. 
 
On the basis of information furnished by the registrant, the above named pesticide is hereby registered 
under the Federal Insecticide, Fungicide and Rodenticide Act. 
 
Registration is in no way to be construed as an endorsement or recommendation of this product by the 
Agency. In order to protect health and the environment, the Administrator, on his motion, may at any 
time suspend or cancel the registration of a pesticide in accordance with the Act. The acceptance of any 
name in connection with the registration of a product under this Act is not to be construed as giving the 
registrant a right to exclusive use of the name or to its use if it has been covered by others. 
 
This product is unconditionally registered in accordance with FIFRA section 3(c)(5) provided that you: 
 
1. Submit and/or cite all data required for registration/reregistration/registration review of your 
product when the Agency requires all registrants of similar products to submit such data. 
 
 
 
Signature of Approving Official: 
 
Rachel C. Holloman, Chief 
Fungicide and Herbicide Branch, 
Registration Division (7505P) 
 
Date: 
 
 
 12/6/18 
EPA Form 8570-6

Page 2 of 2 
EPA Reg. No. 279-3605 
Decision No. 517293 
 
 
 
2. Make the following label changes before you release the product for shipment: 
 
• Revise the EPA Registration Number to read, “EPA Reg. No. 279-3605.” 
 
3. Submit one copy of the revised final printed label for the record before you release the product 
for shipment. 
 
Should you wish to add/retain a reference to the company’s website on your label, then please be aware 
that the website becomes labeling under the Federal Insecticide Fungicide and Rodenticide Act and is 
subject to review by the Agency. If the website is false or misleading, the product would be misbranded 
and unlawful to sell or distribute under FIFRA section 12(a)(1)(E). 40 CFR 156.10(a)(5) list examples 
of statements EPA may consider false or misleading. In addition, regardless of whether a website is 
referenced on your product’s label, claims made on the website may not substantially differ from those 
claims approved through the registration process. Therefore, should the Agency find or if it is brought to 
our attention that a website contains false or misleading statements or claims substantially differing from 
the EPA approved registration, the website will be referred to the EPA’s Office of Enforcement and 
Compliance. 
 
If these conditions are not complied with, the registration will be subject to cancellation in accordance 
with FIFRA section 6. Your release for shipment of the product constitutes acceptance of these 
conditions. A stamped copy of the label is enclosed for your records. Please also note that the record for 
this product currently contains the following CSFs: 
 
• Basic CSF dated 12/21/2017 
 
If you have any questions, please contact Aswathy Balan by phone at 703-347-0510, or via email at 
balan.aswathy@epa.gov.

P a g e | 1 
NOT FOR USE IN CALIFORNIA 
 
F9651-2 Fungicide 
ACTIVE INGREDIENTS: % BY WEIGHT 
*Bixafen: N-(3',4'-dichloro-5-fluorobiphenyl-2-yl)-3-(difluoromethyl)- 
1-methyl-1H-pyrazole-4-carboxamide…………………………………………….14.03% 
**Tebuconazole: alpha-[2-(4-chlorophenyl)ethyl]-alpha- 
(1,1-dimethylethyl)-1H-1,2,4-triazole-1-ethanol………………………………….29.83% 
Other Ingredients……………………………………………………………….….56.14% 
Total………………………………………………………………………………….100.0% 
 
F9651-2 is a suspension concentrate (SC) containing 1.33 pounds bixafen and 2.83 
pounds tebuconazole per gallon. 
*CAS No.: 581809-46-3 and **CAS No.: 107534-96-3 
 
KEEP OUT OF REACH OF CHILDREN 
CAUTION 
 PRECAUCION 
 
Si usted no entiende la etiqueta, busque a alguien para que se la explique a usted en 
detalle. (If you do not understand this label, find someone to explain it to you in detail.) 
 FIRST AID 
IF SWALLOWED x Call a poison control center or doctor immediately for 
treatment advice. 
x Have person sip a glass of water if able to swallow. 
x Do not induce vomiting unless told to do so by a 
poison control center or doctor. 
x Do not give anything by mouth to an unconscious 
person. 
For MEDICAL emergencies, call 24 hours a day at 1-800-331-3148. Have the 
product container or label with you when calling a poison control center or doctor 
or going for treatment. 
For TRANSPORTATION and SPILLS, Call CHEMTREC: (800) 424-9300. 
 
EPA Reg. No. 279-GANL EPA Est. No. 279-NY-1 
 N e t C o n t e n t s : 2 . 5 g a l l o n s 
Sold By 
 FMC Corporation 
2929 Walnut Street 
Philadelphia, PA 19104 
BIXAFEN
 GROUP 7 FUNGICIDE 
TEBUCONAZOLE GROUP 3 FUNGICIDE 
12/06/2018
279-3605

P a g e | 2 
PRECAUTIONARY STATEMENTS 
HAZARDS TO HUMANS AND DOMESTIC ANIMALS 
CAUTION 
Harmful if swallowed. Wash thoroughly with soap and water after handling and before eating, 
drinking, chewing gum, using tobacco or using the toilet. 
 
PERSONAL PROTECTIVE EQUIPMENT (PPE) 
Applicators and other handlers must wear – 
x Long-sleeved shirt and long pants 
x Chemical-resistant gloves (such as natural rubber) 
x Shoe plus socks 
 
USER SAFETY REQUIREMENTS 
Follow manufacturer's instructions for cleaning/maintaining personal protective equipment 
(PPE). If no such instructions for washables exist, use detergent and hot water. Keep and 
wash PPE separately from other laundry. 
 
ENGINEERING CONTROLS 
When handlers use closed systems, enclosed cabs, or aircraft in a manner that meets the 
requirements listed in the Worker Protection Standard (WPS) for agricultural pesticides [40 
CFR 170.240 (d) (4-6)], the handler PPE requirements may be reduced or modified as 
specified in the WPS. 
 
USER SAFETY RECOMMENDATIONS 
Users should: 
x Remove clothing/PPE immediately if pesticide gets inside. Then wash thoroughly and 
put on clean clothing. 
x Remove PPE immediately after handling this product. Wash the outside of gloves 
before removing. As soon as possible, wash thoroughly and change into clean 
clothing. 
 
ENVIRONMENTAL HAZARDS 
This pesticide is toxic to mammals, fish and aquatic invertebrates. For terrestrial uses, do not 
apply directly to water, or to areas where surface water is present or to intertidal areas below 
the mean high-water mark. Drift and runoff may be hazardous to aquatic organisms in 
neighboring areas. Do not contaminate water when disposing of equipment washwater or 
rinsate. 
 
Ground Water Advisory: This pesticide has properties and characteristics associated with 
chemicals detected in ground water. This chemical may leach into ground water if used in 
areas where soils are permeable, particularly where the water table is shallow. 
 
Surface Water Advisory: This pesticide can contaminate surface water through aerial and 
ground spray applications. Under some conditions, it may also have a high potential for runoff 
into surface water after application. These include poorly draining or wet soils with readily 
visible slopes toward adjacent surface waters, frequently flooded areas, areas overlaying 
extremely shallow ground water, areas with in- field canals or ditches that drain to surface

P a g e | 3 
water, areas not separated from adjacent surface waters with vegetated filter strips, and areas 
overlaying tile drainage systems that drain to surface water. 
 
DIRECTIONS FOR USE 
It is a violation of Federal law to use this product in any manner inconsistent with its 
labeling. Read entire label before using this product. 
Do not apply this product in a way that will contact workers or other persons, either directly or 
indirectly or through drift. Only protected handlers may be in the area during application. For 
any requirements specific to your State or Tribe, consult the agency responsible for pesticide 
regulation. 
 
FAILURE TO FOLLOW THE DIRECTIONS FOR USE AND PRECAUTIONARY 
STATEMENTS ON THIS LABEL MAY RESULT IN POOR DISEASE CONTROL, CROP 
INJURY AND/OR ILLEGAL RESIDUES. 
 
[Optional state restriction language for the state of NY: Not for sale, distribution, or use in -- 
Counties of New York State.] 
 
RESISTANCE MANAGEMENT 
For resistance management, please note that F9651-2 contains both a Group 7 (Bixafen) and 
Group 3 (Tebuconazole) fungicide. Any fungal population may contain individuals naturally 
resistant to F9651-2 and other Groups 7 or Group 3 fungicides. A gradual or total loss of pest 
control may occur over time if these fungicides are used repeatedly in the same fields. 
Appropriate resistance-management strategies must be followed. 
 
To delay fungicide resistance, take one or more of the following steps: 
x Use tank mixtures with fungicide from a different group that a re equally effective on the 
target pest when such use is permitted. Use at least the minimum application rate as 
labeled by the manufacturer. 
x Adopt an integrated disease management program for fungicide u se that includes 
scouting, uses historical information related to pesticide use, and crop rotation, and 
which considers host plant resistance, impact of environmental conditions on disease 
development, disease thresholds, as well as cultural, biological and other chemical 
control practices. 
x Where possible, make use of predictive disease models to effec tively time fungicide 
applications. Note that using predictive models alone is not sufficient to manage 
resistance. 
x Monitor treated fungal populations for resistance development. 
x Contact your local extension specialist or certified crop advi sor for any additional 
pesticide resistance-management and/or IPM recommendations for specific crops and 
pathogens. 
x For further information or to report suspected resistance cont act your pesticide 
distributor or university extension specialist.

P a g e | 4 
AGRICULTURAL USE REQUIREMENTS 
Use this product only in accordance with its labeling and with the Worker Protection Standard, 40 CFR 
part 170. This Standard contains requirements for the protection of agricultural workers on farms, forests, 
nurseries, and greenhouses, and handlers of agricultural pesticides. It contains requirements for training, 
decontamination, notification, and emergency assistance. It also contains specific instructions and 
exceptions pertaining to the statements on this label about personal protective equipment (PPE) and re-
entry interval. The requirements in this box only apply to uses of this product that are covered by the 
Worker Protection Standard. 
 
Do not enter or allow worker entry into treated areas during the restricted entry interval (REI). The REI for 
each crop is listed in the application directions associated with each crop. 
 
PPE required for early entry to treated areas that is permitted under the Worker Protection Standard and 
that involves contact with any- thing that has been treated, such as plants, soil, or water, is: coveralls, 
chemical-resistant gloves (barrier laminate, butyl rubber (> 14 mils), nitrile rubber (> 14 mils), neoprene 
rubber (> 14 mils), polyvinyl chloride (PVC) (> 14 mils), or viton (> 14 mils)), and shoes plus socks. 
 
 
STORAGE AND DISPOSAL 
Do not contaminate water, food, or feed by storage or disposal. 
 
PESTICIDE STORAGE 
If storing this product below freezing, user must shake or roll the container to ensure proper product 
consistency. Keep out of reach of children and animals. Store in original containers only. Store in a cool, 
dry place and avoid excess heat. Carefully open containers. After partial use, replace lids and close 
tightly. Do not put concentrate or dilute material into food or drink containers. Do not contaminate other 
pesticides, fertilizers, water, food, or feed by storage or disposal. In case of spill, avoid contact, isolate 
area and keep out animals and unprotected persons. Confine spills. Call FMC: 1-(800)-331-3148. To 
confine spill: If liquid, dike surrounding area or absorb with sand, cat litter or commercial clay. Place 
damaged package in a holding container. Identify contents. 
 
PESTICIDE DISPOSAL 
Wastes resulting from the use of this product may be disposed of on site or at an approved waste disposal 
facility. 
 
CONTAINER HANDLING 
Non-refillable container. Do not reuse or refill this container. Triple rinse container (or equivalent) promptly 
after emptying. Triple rinse as follows: Empty the remaining contents into application equipment or a mix 
tank and drain for 10 seconds after the flow begins to drip. Fill the container ¼ full with water and recap. 
Shake for 10 seconds. Pour rinsate into application equipment or a mix tank or store rinsate for later use 
or disposal. Drain for 10 seconds after the flow begins to drip. Repeat this procedure two more times Offer 
for recycling, if available, or reconditioning or puncture and dispose of in a sanitary landfill or by 
incineration or, if allowed by state and local authorities, by burning. If burned, stay out of smoke. 
 
RETURNABLE -- REFILLABLE CONTAINERS 
Refillable container. Refill this container with F9651-2 Fungicide only. Do not reuse this container for any 
other purpose. Cleaning the container before final disposal is the responsibility of the person disposing of 
the container. 
Cleaning before refilling is the responsibility of the refiller. To clean the container before final disposal, 
empty the remaining contents from this container into application equipment or mix tank. Fill the 
container about 10 percent full with water. Agitate vigorously or recirculate water with the pump for 2 
minutes. Pour or pump rinsate into application equipment or rinsate collection system. Repeat this rinsing 
procedure two more times. This material may be repackaged in 30 gallon returnable-refillable containers 
by FMC Corporation or a registered establishment under contract to FMC Corporation. After use, return 
the container to the point of purchase or designated locations. Prior to refilling, inspect thoroughly for 
damage such as cracks, punctures, abrasions and damaged or worn out threads on closure devices. Do 
not refill or transport damaged or leaking containers. Check for leaks after refilling and before 
transportation. If the container is not being refilled, return it to the point of purchase.

P a g e | 5 
 
SPRAY DRIFT MANAGEMENT 
SENSITIVE AREAS: 
The pesticide must only be applied when the potential for drift to adjacent sensitive areas (e.g., 
residential areas, bodies of water, known habitats for threatened or endangered species, non-
target crops) is minimal (e.g., when wind is blowing away from the sensitive areas). 
Avoiding spray drift at the application site is the responsibility of the applicator. The interaction 
of many equipment and weather-related factors determine the potential for spray drift. The 
applicator and the grower are responsible for considering all these factors when making 
decisions. 
The following drift management requirements must be followed to avoid off-target drift 
movement from aerial applications to agricultural field crops. These requirements do not apply 
to forestry applications, public health uses or to applications using dry formulation. 
1. The distance of the outer most nozzles on the boom must not exceed 3/4 the length of 
the wingspan or rotor. 
2. Nozzles must always point backward parallel with the air str eam and never be pointed 
downwards more than 45 degrees. 
Where states have more stringent regulations, they must be observed. The applicator must be 
familiar with and take into account the information covered below. 
 
INFORMATION ON DROPLET SIZE: 
The most effective way to reduce drift potential is to apply large droplets. The best drift 
management strategy is to apply the largest droplets that provide sufficient coverage and 
control. Applying larger droplets reduces drift potential but will not prevent drift if applications 
are made improperly, or under unfavorable environmental conditions (see Wind, Temperature 
and Humidity, and Temperature Inversions below). 
 
CONTROLLING DROPLET SIZE: 
x Volume - Use high flow rate nozzles to apply the highest pract ical spray volume. 
Nozzles with higher rated flows produce larger droplets. 
x Pressure - Do not exceed the nozzle manufacturer’s recommended pressures. For 
many nozzle types, lower pressure produces larger droplets. When higher flow rates are 
needed, use higher flow rate nozzles instead of increasing pressure. 
x Number of nozzles - Use the minimum number of nozzles that pro vide uniform 
coverage. 
x Nozzle Orientation - The nozzles must be oriented such that th e spray is released 
parallel to the airstream. This produces larger droplets than other orientations. 
Significant deflection from horizontal will reduce droplet size and increase drift potential. 
x Nozzle Type - Use a nozzle type that is designed for the inten ded application. With 
most nozzle types, narrower spray angles produce larger droplets. Consider using low-
drift nozzles. Solid stream nozzles oriented straight back produce the largest droplets 
and the lowest drift. 
 
BOOM LENGTH: 
For some use patterns, reducing the effective boom length to less than 3/4 of the wingspan or 
rotor length may further reduce drift without reducing swath width. 
 
APPLICATION HEIGHT:

P a g e | 6 
Applications must not be made at a height greater than 10 feet above the top of the largest 
plants unless a greater height is required for aircraft safety. Making applications at the lowest 
height that is safe reduces exposure of droplets to evaporation and wind. 
 
SWATH ADJUSTMENT: 
When applications are made with a crosswind, the swath will be displaced downwind. 
Therefore, on the up and downwind edges of the field, the applicator must compensate for this 
displacement by adjusting the path of the aircraft upwind. Swath adjustment distance must 
increase, with increasing drift potential (higher wind, smaller drops, etc.) 
 
WIND: 
Drift potential is lowest between wind speeds of 2 - 10 mph. However, many factors, including 
droplet size and equipment type determine drift potential at any given speed. Application must 
be avoided below 2 mph due to variable wind direction and high inversion potential. 
 
NOTE: Local terrain can influence wind patterns. Every applicator must be familiar with local 
wind patterns and how they affect spray drift. 
 
TEMPERATURE AND HUMIDITY: 
When making applications in low relative humidity, set up equipment to produce larger droplets 
to compensate for evaporation. Droplet evaporation is most severe when conditions are both 
hot and dry. 
 
TEMPERATURE INVERSIONS: 
Applications must not occur during a temperature inversion because drift potential is high. 
Temperature inversions restrict vertical air mixing, which causes small suspended droplets to 
remain in a concentrated cloud. This cloud can move in unpredictable directions due to the 
light variable winds common during inversions. Temperature inversions are characterized by 
increasing temperatures with altitude and are common on nights with limited cloud cover and 
light to no wind. They begin to form as the sun sets and often continue into the morning. Their 
presence can be indicated by ground fog; however, if fog is not present, inversions can also be 
identified by the movement of smoke from a ground source or an aircraft smoke generator. 
Smoke that layers and moves laterally in a concentrated cloud (under low wind conditions) 
indicates an inversion, while smoke that moves upward and rapidly dissipates indicates good 
vertical air mixing. 
 
APPLICATION AND CALIBRATION TECHNIQUES FOR CHEMIGATION 
 
Apply this product only through center pivot, motorized lateral move, traveling gun, solid set 
and portable (wheel move, side roll, end tow, or hand move) irrigation system(s). Do not apply 
this product through any other type of irrigation system. Crop injury, lack of effectiveness, or 
illegal pesticide residues in the crop can result from non-uniform distribution of treated water. If 
you have questions about calibration, you must contact State Extension Service specialists, 
equipment manufacturers or other experts. Do not apply this product through irrigation systems 
connected to a public water system. “Public water system” means a system for the provision to 
the public of piped water for human consumption if such system has at least 15 service 
connections or regularly serves an average of at least 25 individuals daily at least 60 days per 
year. Controls for both irrigation water and pesticide injection systems must be functionally 
interlocked, to automatically terminate pesticide injection when the irrigation water pump motor 
stops. A person knowledgeable of the irrigation system and responsible for its operation shall

P a g e | 7 
be present to discontinue pesticide injection and make necessary adjustments, should the 
need arise. 
 
The irrigation water pipeline must be fitted with a functional, automatic, quick-closing check 
valve to prevent the flow of treated irrigation water back toward the water source. The pipeline 
must also be fitted with a vacuum relief valve and low pressure drain, located between the 
irrigation water pump and the check valve, to prevent back-siphoning of treated irrigation water 
into the water source. Always inject F9651-2 Fungicide into irrigation water after it discharges 
from the irrigation pump and after it passes through the check valve. Never inject pesticides 
into the intake line on the suction side of the pump. Pesticide injection equipment must be 
fitted with a functional, normally closed, solenoid- operated valve located on the intake side of 
the injection pump. Interlock this valve to the power system, to prevent fluid from being 
withdrawn from the chemical supply tank when the irrigation system is either automatically or 
manually turned off. 
 
The pesticide injection pipeline must contain a functional, automatic, quick-closing check valve 
to prevent the flow of fluid back toward the injection pump. The irrigation line or water pump 
must include a functional pressure switch which will stop the water pump motor when the water 
pressure decreases to the point where pesticide distribution is adversely affected. Spray 
mixture in the chemical supply tank must be agitated always, otherwise settling and uneven 
application may occur. Do not apply when wind speed favors drift beyond the area intended for 
treatment. Systems must use a metering pump, such as a positive displacement injection 
pump (e.g., diaphragm pump), effectively designed and constructed of materials that are 
compatible with pesticides and capable of being fitted with a system interlock. 
 
F9651-2 Fungicide may be used through two basic types of sprinkler irrigation systems as 
outlined in Sections A and B below. Determine which type of system is in place, then refer to 
the appropriate directions provided for each type. 
 
A. Center Pivot, Motorized Lateral Move and Traveling Gun Irrig ation Equipment 
 
For injection of pesticides, these continuously moving systems must use a positive 
displacement injection pump, of either diaphragm or piston type, constructed of materials that 
are compatible with pesticides and capable of being fitted with a system interlock and capable 
of injection at pressures approximately 2-3 times those encountered within the irrigation water 
line. Venturi applicator units cannot be used on these systems. Thoroughly mix specified 
amount of F9651-2 Fungicide for acreage to be covered into same amount of water used 
during calibration and inject into system continuously for one revolution or run. Mixture in the 
chemical supply tank must be continuously agitated during the injection run. Shut off injection 
equipment after one revolution or run but continue to operate irrigation system until F9651-2 
Fungicide has been cleared from last sprinkler head. 
 
B. Solid Set and Portable (Wheel Move, Side Roll, End Tow, or H and Move) Irrigation 
Equipment 
With stationary systems, an effectively designed in-line venturi applicator unit is preferred 
which is constructed of materials that are compatible with pesticides; however, a positive-
displacement pump can also be used. Determine acreage covered by sprinkler. Fill tank of 
injection equipment with water and adjust flow to use contents over a thirty to forty-five-minute 
period. Mix desired amount of F9651-2 Fungicide for acreage to be covered with water so that 
the total mixture of F9651-2 Fungicide plus water in the injection tank is equal to the quantity of 
water used during calibration and operate entire system at normal pressures recommended by

P a g e | 8 
the manufacturer of injection equipment used, for amount of time established during 
calibration. Mixture in the chemical supply tank must be continuously agitated during the 
injection run. F9651-2 Fungicide can be injected at the beginning or end of the irrigation cycle 
or as a separate application. Stop injection equipment after treatment is completed and 
continue to operate irrigation system until F9651-2 Fungicide has been cleared from last 
sprinkler head. 
 
MIXING INSTRUCTIONS 
Ensure the sprayer tank, filter and lines are clean, then partially fill the spray tank with clean 
water. Measure the required amount of F9651-2 Fungicide and add this to the tank. 
Agitate to ensure thorough mixing while filling tank with remaining water. Maintain agitation 
during application and apply with properly calibrated application equipment. Do not allow spray 
mixture to stand overnight or for prolonged periods, as some chemical breakdown may occur. 
A high quality, nonionic spreader can be used as a spray tank additive for every application. 
F9651-2 Fungicide must be added to the tank before the addition of any adjuvant. Consult the 
adjuvant label or manufacturer for crop tolerance and safety information when used with 
F9651-2 Fungicide. 
 
APPLICATION TIMING 
F9651-2 Fungicide can be used in a preventive spray program to manage diseases in labeled 
crops. Complementary dual modes of action provided by F9651-2 Fungicide helps prevent the 
development of disease resistance. It is directed that this product be used within an Integrated 
Pest Management Program (IPM), rotating with non FRAC 3 or FRAC 7 fungicides. Carefully 
read, and understand, and follow all directions and precautions. Disease pressure and 
environmental conditions will determine application rates and the length of the spray intervals. 
Consult local disease advisory system recommendations to determine the predicted disease 
pressure and the associated application rates and intervals. 
 
COMPATIBILITY 
The tank mixing behavior of this fungicide with other pesticides has not been fully investigated. 
If tank mixing with other pesticides is desirable, conduct a jar test with rates and volumes of 
carrier typically used in an agricultural application. Look for signs of separation, globules, 
sludge, flakes or other precipitates. DO NOT tank mix with the other pesticide if the jar test with 
F9651-2 Fungicide has indicated incompatibility. Follow the most restrictive labeling on this 
label or the tank mixture partner. Before adding F9651-2 Fungicide along with other additives 
or pesticide products to a spray tank, a compatibility jar test must be conducted. 
 
It is the pesticide user’s responsibility to ensure that all products are registered for the intended 
use. Read and follow the applicable restrictions and limitations and directions for use on all 
product labels involved in tank mixing. Users must follow the most restrictive directions for use 
and precautionary statements of each product in the tank mixture. 
 
Compatibility Jar Test: 
F9651-2 Fungicide is compatible with most products, however not all have been tested. Use 
the following compatibility test to ensure physical compatibility. 
 
Using a quart jar, add the proportionate amounts of the products to approximately one quart of 
water with agitation. Add wettable powders and water dispersible granular products first, next 
liquid flowables, then emulsifiable concentrates, and last liquid soluble products. After thorough 
mixing, allow this mixture to stand for 5 minutes. If the combination remains mixed or can be 
readily remixed, it is physically compatible. Once compatibility has been proven, use the same

P a g e | 9 
procedure for adding products to the spray tank. Use tank mix combinations on a small 
number of plants before treating larger areas. When tank mixing, follow more restrictive 
labeling of any tank mix partner. Do not tank mix with any product that contains a prohibition 
on tank mixing. 
 
Before applying any tank mixture not specifically directed on this label, the crop safety of the 
target crop must be confirmed by applying the mixture to a small area of the target crop in 
accordance to the label instructions. 
 
FOLIAR APPLICATION 
Maximum benefit of F9651-2 Fungicide from foliar applications requires coverage both outside 
and inside the plant canopy. Thorough coverage of foliage is obtained by using proper spray 
pressure, a minimum of 10 gallons per acre, appropriate nozzles that provide uniform spray 
distribution and minimize drift, nozzle spacing and sprayer speed. Follow directions of nozzle 
manufacturer for nozzle pressures.
 
 
ROTATIONAL CROP GUIDELINES: After making the last F9651-2 Fungicide 
application, rotational crops may be planted with the following intervals: 
 0 days F9651-2 Fungicide labeled crops 
 30 days Leafy crops 
 365 days Unlabeled crops 
 
RESTRICTIONS 
AERIAL APPLICATION: 
Do not apply in less than 2 gallons per acre. 
 
CHEMIGATION APPLICATION: 
Do not apply by flood systems. 
 
WATER BODIES: 
Do not apply when spray could drift into a body of water. 
 
FORAGE: 
Do not harvest or feed forage until number of days specified after last F9651-2 Fungicide 
application for each crop. 
 
RATE EQUIVALENCY TABLE 
Product Rate 
(fl. oz./A) 
Total Active 
Ingredient Rate 
(lb a.i./A) 
Equivalent Bixafen 
Active Ingredient Rate 
(lb a.i./A) 
Equivalent 
Tebuconazole Active 
Ingredient Rate 
(lb a.i./A) 
3.5 0.114 0.036 0.077 
5.0 0.163 0.052 0.110 
6.6 0.215 0.069 0.146

P a g e | 10 
FIELD AND ROW CROPS 
 
Crop Disease (Pathogen) Single Use Rate Application 
Instructions 
Corn 
(sweet 
corn, field 
corn, field 
corn grown 
for seed 
and 
popcorn) 
Gray leaf spot 
(Cercospora sorghi) 
 
Southern corn rust 
(Puccinia polysora) 
 
Common corn rust 
(Puccinia sorghi) 
 
Northern corn leaf 
blight 
(Setosphaeria turcica) 
 
Southern corn leaf 
blight (Cochliobolus 
heterostrophus) 
 
Northern corn leaf spot 
(Cochliobolus 
carbonum) 
 
Eyespot (Kabatiella 
zeae) 
 
Anthracnose leaf blight 
(Glomerella 
graminicola) 
 
Diplodia ear rot and 
stalk rot 
(Botryosphaeria 
festucae, Diplodia 
frumenti, Diplodia 
maydis) 
 
Physoderma brown 
spot (Physoderma 
maydis) 
 
Yellow leaf blight 
(Phyllosticta maydis) 
 
Tar spot 
(Phyllachora maydis) 
 
 
 5.0 – 6.6 fl. oz./A 
 
 (0.163 – 0.215 lb. a.i./A) 
Foliar disease: Apply 
F9651-2 by aerial, ground 
and/or chemigation in a 
protective spray schedule, 
or when weather 
conditions are favorable 
for disease development. 
Repeat applications at 7- 
to 14-day intervals. When 
disease is high, use the 
higher rate and shorter 
interval. 
 
For optimum control of 
foliar diseases, a 
surfactant must be tank-
mixed with F9651-2. 
 
For management of fungal 
pathogen resistance 
development, do not 
make more than 2 
sequential applications 
per year before alternating 
to another fungicide from 
a FRAC group different 
from FRAC groups 7 and 
3. 
 Restrictions: 
x Not registered for use in California. 
x Maximum 2 applications per year. 
x Do not apply more than 13.2 fl. oz. of product/A per year. 
x Do not apply more than 0.675 lb. a.i. of tebuconazole/A per ye ar from all tebuconazole 
containing products. 
x Do not apply more than 0.138 lb. a.i. of bixafen/A per year fr om all bixafen containing products. 
x Restricted-entry interval (REI) = 12 hours. 
x Do not use an adjuvant after the V8 stage and prior to the VT stage of corn. An adjuvant may 
be used at any other growth stage. 
x Do not apply after R4 growth stage of corn. 
x F9651-2 may be applied up to 10 days before harvest for forage , and 30 days before harvest 
for grain or stover.

P a g e | 11 
 
Crop Disease (Pathogen) Single Use Rate Application Instructions 
Peanut Stem rot [white mold, 
southern blight, southern 
stem rot] (Sclerotium rolfsii) 
 
Rhizoctonia limb rot 
(Rhizoctonia solani) 
 
Early leaf spot 
(Mycosphaerella arachidis, 
Cercospora arachidicola) 
 
Late leaf spot 
(Mycosphaerella berkeleyi, 
Phaeoisariopsis personata) 
 
Leaf Rust (Puccinia 
arachidis) 
 
Web blotch (Phoma sp) 
 
Pepper spot 
(Leptosphaerulina sp) 
 
Aspergillus crown rot 
(Aspergillus niger) 
 
Cylindrocladium black rot 
(Cylindrocladium 
crotalariae) 
5.0 – 6.6 fl. oz./A 
 
 (0.163 – 0.215 lb. a.i./A 
Soil disease: For best control in 
high infestation level field, apply 
three applications by ground, 
aerial and/or chemigation using 
the maximum rate at 2, 3 and 4 
of a 7- application preventive 
spray schedule. For most fields 
two applications at application 
timings 2 and 4 (28-day interval) 
is advised. 
 
Apply as a 30-40 gal/A spray, 
targeting the root and pod zone 
with nozzles producing large 
droplets to penetrate canopy. For 
soil-borne diseases, rainfall or 
irrigation will optimize activity of 
F9651-2. 
 
Foliar disease: Apply F9651-2 
by aerial, ground and/or 
chemigation. Apply the lower 
rate early and higher later in a 
preventive spray schedule. 
Repeat applications at 7 to 14-
day intervals. When disease is 
high, use the higher rate and 
shorter interval. For optimum 
control of foliar diseases, a 
surfactant must be tank-mixed 
with F9651-2. 
 
To discourage development of 
resistant strains of 
pathogens, applications of 
different FRAC group 
fungicide must be made prior to 
and following applications of 
F9651-2. 
Restrictions: 
• Not registered for use in California. 
• Maximum 3 applications of soil and/or foliar sprays per year. 
• Do not apply more than 19.8 fl. oz. of product/A per year. 
• Do not apply more than 0.81 lb. a.i. of tebuconazole/A per ye ar from all tebuconazole containing 
products. 
• Do not apply more than 0.207 lb. a.i. of bixafen/A per year f rom all bixafen containing products. 
• Restricted-entry interval (REI) = 12 hours. 
• F9651-2 may be applied up to 14 days before harvest. 
• Do not feed hay or threshings or allow livestock to graze in treated areas.

P a g e | 12 
 
Crop Disease (Pathogen) Single Use Rate Application Instructions 
Soybean Brown spot (Septoria 
glycines) 
 
Frogeye leaf spot 
(Cercospora sojina) 
 
Cercospora leaf blight 
[purple seed stain] 
(Cercospora kikuchii) 
 
Rust (Phakopsora 
meibomiae) 
 
White mold (Sclerotinia 
sclerotiorum) 
 
Anthracnose (Colletotrichum 
truncatum) 
 
Pod and stem blight 
(Diaporthe phaseolorum) 
 
Aerial web blight 
(Thanatephorus cucumeris, 
Rhizoctonia solani) 
 
Target spot (Corynespora 
cassiicola) 
 
Powdery mildew 
(Microsphaera diffusa) 
3.5 – 6.6 fl. oz./A 
 
 (0.114 – 0.215 lb. a.i/A 
Apply F9651-2 by aerial, ground 
and/or chemigation in a 
protective spray schedule or 
when weather conditions are 
favorable for disease 
development. Repeat 
applications at 10 to 14-day 
intervals. 
For optimum control of foliar 
diseases, a surfactant must be 
tank-mixed with F9651-2. 
 
For management of fungal 
pathogen resistance 
development, do not make 
more than 2 sequential 
applications per year before 
alternating to another 
fungicide from a FRAC group 
different from FRAC groups 7 
and 3. 
Restrictions: 
• Not approved for use in New York . 
• Not registered for use in California. 
• Maximum 2 applications per year. 
• Do not apply more than 13.2 fl. oz. of product/A per year. 
• Do not apply more than 0.337 lb. a.i. of tebuconazole/A per y ear from all tebuconazole 
containing products. 
• Do not apply more than 0.138 lb. a.i. of bixafen/A per year f rom all bixafen containing products. 
• Restricted-entry interval (REI) = 12 hours. 
• F9651-2 may be applied up to 21 days before harvest. 
• Do not feed hay or threshings or allow livestock to graze in treated areas.

P a g e | 13 
Crop Disease (Pathogen) Single Use Rate Application Instructions 
Wheat 
Barley 
Leaf rust 
(Puccina triticina = Puccinia 
recondita) 
 
Stripe rust 
(Puccinia striformis) 
 
Stagonospora leaf / glume 
blotch 
[=Septoria leaf & glume 
blotch] 
(Phaeosphaeria 
herpotrichoides) 
 
Tan spot 
(Pyrenophora tritici- 
repentis) 
 
Septoria leaf blotch 
(Mycosphaerella 
graminicola, anamorph 
Septoria tritici) 
Stem rust 
(Puccinia graminis) 
Powdery mildew 
(Blumeria graminis) 
Sooty mold 
(Cladosporium sp, Alternaria 
sp) 
 
Eyespot [=foot rot] 
(Tapesia yallundae, = 
Pseudocercosporella 
herpotrichoides) 
Spot blotch 
(Cochliobolus stivus) 
 
3.5 – 5.0 fl. oz./A 
 
(0.114 – 0.163 lb. a.i./A) 
 
 
Apply F9651-2 by aerial, ground 
and/or chemigation in a 
protective spray schedule or 
when weather conditions are 
favorable for disease 
development and disease 
thresholds are met. Apply lower 
rates early season. Application 
of high rate at flag leaf ligule 
emergence protects the upper 
foliage during critical grain fill 
period. 
Repeat applications at 10 to 14-
day intervals. 
 
For optimum control of foliar 
diseases, a surfactant must be 
tank-mixed with F9651-2. 
F9651-2 needs two to four 
hours of drying time on plant 
foliage to move systemically into 
plant tissue and be resistant to 
weathering, before rain or 
irrigation occurs. 
 
For management of fungal 
pathogen resistance 
development, do not make more 
than 2 sequential applications 
per year before 
alternating to another fungicide 
from a FRAC 
group different from FRAC 
groups 7 and 3. 
Restrictions: 
• Not registered for use in California. 
• Maximum 1 application per year. 
• Do not apply more than 5.0 fl. oz. of product/A per year. 
• Do not apply more than 0.112 lb. a.i. of tebuconazole/A per y ear from all tebuconazole 
containing products. 
• Do not apply more than 0.052 lb. a.i. of bixafen/A per year f rom all bixafen containing products. 
• Restricted-entry interval (REI) = 12 hours. 
• F9651-2 may be applied up to 10 days before harvest for forag e, 20 days for hay, and 30 days 
before harvest for grain or stover.

P a g e | 14 
 
CONDITIONS OF SALE AND LIMITATION OF WARRANTY AND LIABILITY 
 
Notice: Read the entire Directions for Use and Conditions of Sale and Limitation of 
Warranty and Liability before buying or using this product. If the terms are not 
acceptable, return the product at once, unopened, and the purchase price will be 
refunded. 
 
The Directions for Use of this product must be followed carefully. It is impossible to 
eliminate all risks inherently associated with the use of this product. Crop injury, 
ineffectiveness, or other unintended consequences may result because of such 
factors as manner of use or application, weather or crop conditions beyond the control 
or FMC or Seller. All such risks shall be assumed by Buyer and User, and, to the 
extent permitted by applicable law, Buyer and User agree to hold FMC and Seller 
harmless for any claims relating to such factors. Seller warrants that this product 
conforms to the chemical description on the label and is reasonably fit for the 
purposes stated on the Directions for Use when used in accordance with the 
directions under normal conditions of use. TO THE EXTENT PERMITTED BY 
APPLICABLE LAW, FMC MAKES NO WARRANTIES OF MERCHANTABILITY OR 
OF FITNESS FOR A PURPOSE, NOR ANY OTHER EXPRESS OR IMPLIED 
WARRANTIES WITH RESPECT TO THE SELECTION, PURCHASE, OR USE OF 
THIS PRODUCT. Any warranties, express or implied, having been made are 
inapplicable if this product has been used contrary to label instructions, or under 
abnormal conditions, or under conditions not reasonably foreseeable to (or beyond the 
control of) seller or FMC, and, to the extent permitted by applicable law, buyer 
assumes the risk of any such use. 
To the extent permitted by applicable law, FMC or seller shall not be liable for any 
incidental, consequential or special damages resulting from the use or handling of this 
product. TO THE EXTENT PERMITTED BY APPLICABLE LAW, THE EXCLUSIVE 
REMEDY OF THE USER OR BUYER, AND THE EXCLUSIVE LIABILITY OF FMC 
AND SELLER FOR ANY AND ALL CLAIMS. LOSSES, INJURIES OR DAMAGES 
(INCLUDING CLAIMS BASED ON BREACH OF WARRANTY, CONTRACT, 
NEGLIGENCE, TORT, STRICT LIABILITY OR OTHERWISE) RESULTING FROM 
THE USE OR HANDLING OF THIS PRODUCT, SHALL BE THE RETURN OF THE 
PURCHASE PRICE OF THE PRODUCT OR, AT THE ELECTION OF FMC OR 
SELLER, THE REPLACEMENT OF THE PRODUCT. 
 
This Conditions of Sale and Limitation of Warranty and Liability may not be amended 
by any oral or written agreement. 
 
F9651-2 Fungicide and FMC – Trademarks of FMC Corporation 
 
© 2015-2018 FMC Corporation all rights reserved. 
 
Label Tracking: 20 November 2018