crop-chem-docs/corpus/epa_ppls/264-819.md

FLUFENACET 4 SC FLOWABLE HERBICIDE

• EPA Reg No: 264-819
• Registrant: BAYER CROPSCIENCE, LLC
• Signal word: Caution
• Active ingredients: Flufenacet (41%)
• Label accepted: 2021-04-30
• Source PDF: https://www3.epa.gov/pesticides/chem_search/ppls/000264-00819-20210430.pdf

---

UNITED STATES ENVIRONMENTAL PROTECTION AGENCY WASHINGTON, DC 20460

Amended Under Reregistration and Label Amendment v.20150612

OFFICE OF CHEMICAL SAFETY AND POLLUTION PREVENTION April 30, 2021

Steven Callen Bayer CropScience LP 800 N. Lindbergh Blvd. St. Louis, MO 63167

Subject: Registration Review Label Mitigation for Flufenacet Product Name: Flufenacet 4 SC Flowable Herbicide EPA Registration Number: 264-819 Application Date: 7/16/2019 Decision Number: 553277

Dear Mr. Callen:

The Agency, in accordance with the Federal Insecticide, Fungicide and Rodenticide Act (FIFRA), as amended, has completed reviewing all of the information submitted with your application to support the Registration Review of the above referenced product in connection with the Flufenacet Interim Decision, and has concluded that your submission is acceptable. The agency also completed review of your amended label referred to above, submitted in connection with registration under FIFRA, as amended, and has determined the label is also acceptable.

Should you wish to add/retain a reference to the company’s website on your label, then please be aware that the website becomes labeling under the Federal Insecticide Fungicide and Rodenticide Act and is subject to review by the Agency. If the website is false or misleading, the product would be misbranded and unlawful to sell or distribute under FIFRA section 12(a)(1)(E). 40 CFR 156.10(a)(5) list examples of statements EPA may consider false or misleading. In addition, regardless of whether a website is referenced on your product’s label, claims made on the website may not substantially differ from those claims approved through the registration process. Therefore, should the Agency find or if it is brought to our attention that a website contains false or misleading statements or claims substantially differing from the EPA approved registration, the website will be referred to the EPA’s Office of Enforcement and Compliance. A copy of your label stamped “Accepted” is enclosed. Products shipped after 12 months from the date of this amendment must bear the new revised label. Your release for shipment of the product bearing the amended label constitutes acceptance of these conditions. If these conditions are not complied with, the registration will be subject to cancellation in accordance with FIFRA section 6.

Page 2 of 2 EPA Reg. No. 264-819 Decision No. 553277

If you have any questions about this letter, please contact Jaclyn Pyne by phone at 703-347- 0445, or via email at pyne.jaclyn@epa.gov.

Sincerely,

Linda Arrington, Branch Chief Risk Management and Implementation Branch 4 Pesticide Re-Evaluation Division Office of Pesticide Programs

Enclosure

1

Flufenacet 4 SC Herbicide ABN: DEFINE™ SC HERBICIDE FOR CONTROL OF CERTAIN GRASS AND BROADLEAF WEEDS IN CORN AND SOYBEANS ACTIVE INGREDIENT: Flufenacet N-(4-Fluorophenyl)-N-(1-methylethyl)-2-[[5--(trifluoromethyl)-1,3,4-thiadiazol-2-yl]-oxy]acetamide ........................ 41.0% OTHER INGREDIENTS: .......................................................................................................................................... 59.0% Contains 4 lbs of N-(4-Fluorophenyl)-N-(1-methylethyl)-2-[[5-(trifluoromethyl)-1,3,4-thiadiazol-2-yl]-oxy]acetamide per gallon. Total 100.0% EPA Reg No. 264-819 EPA Est. No. KEEP OUT OF REACH OF CHILDREN CAUTION For MEDICAL And TRANSPORTATION Emergencies ONLY Call 24 Hours A Day 1-800-334-7577 For PRODUCT USE Information Call 1-866-99BAYER (1-866-992-2937) See [Back][Side] Panel for First Aid Instructions and [Leaflet][Booklet] for Complete Precautionary Statements and Directions for Use. (Note to reviewer: Location of additional precautionary statements, directions for use will vary between those listed, depending on container type/size.) FIRST AID IF SWALLOWED: x Call a poison control center or doctor immediately for treatment advice. x Have person sip a glass of water if able to swallow. x Do not induce vomiting unless told to do so by a poison control center or doctor. x Do not give anything by mo uth to an unconscious person. IF ON SKIN OR CLOTHING: x Take off contaminated clothing. x Rinse skin immediately with plenty of water for 15-20 minutes. x Call a poison control center or doctor for treatment advice. For MEDICAL Emergencies Call 24 Hours A Day 1-800-334-7577. Have the product container or label with you when calling a poison control center or doctor or going for treatment. NOTE TO PHYSICIAN: No specific antidote is available. Treat the patient symptomatically.

FLUFENACET GROUP 15 HERBICIDE Apr 30, 2021 264-819

2

PRECAUTIONARY STATEMENTS HAZARDS TO HUMANS AND DOMESTIC ANIMALS CAUTION Harmful if swallowed or absorbed through skin. Avoid contact with skin, eyes, or clothing. Removing and washing contaminated clothing before reuse may reduce exposure. Personal Protective Equipment: All handlers must wear a minimum of: long sleeved shirt, long pants, shoes and socks, and chemical resistant gloves. Additional required PPE for specific activities/crops are included in the application instructions for each crop. Corn In addition to the PPE for all handlers, mixers and loaders must use Engineering Controls that meet the requirements listed in the WPS for agricultural pesticides (40 CFR 170. 607(d)(2)(i) &(ii)] for dermal and inhalation protection. Except when using an enclosed cab that meet the requirements listed in the WPS for agricultural pesticides (40 CFR 170. 305for dermal and inhalation protection, applicators must wear the following PPE in addition the PPE required for all handlers: x a NIOSH approved particulate re spirator with any N,R,or P filt er with NIOSH approval number prefix TC- 84A. Higher-level respirators that are NIOSH approved for particulates can also be used. Soybeans Mixers and Loaders must use Engineering Controls that meet the requirements listed in the WPS for agricultural pesticides (40 CFR 170. 607(d)(2)(i) &(ii)] for dermal and inhalation protection. Follow manufacturer’s instructions forcleaning/maintaining PPE. If no such instructions for washables, use detergent and hot water. Keep and wash PPE separately from other laundry.

ENGINEERING CONTROLS When handlers use closed systems, enclosed cabs, or aircraft in a manner that meets the requirements listed in the Worker Prote ction Standard (WPS) for agricultural pesticides (40 CFR 170.240(d)(4-6 )), the handler PPE requirements may be reduced or modified as specified in the WPS.

User Safety Recommendations User should: ƒ Wash hands before eating, drinking, chewing gum, using tobacco or using the toilet. ƒ Remove clothing immediat ely if pesticide gets inside. Then wash thoroughly and put on clean clothing. ƒ Remove PPE immediately after handling this product. Wash the ou tside of gloves before removing. As soon as possible, wash thoroughly and change into clean clothing.

3

ENVIRONMENTAL HAZARDS For Terrestrial Uses: Do not apply di rectly to water, or to areas where surface water is present or to intertidal areas below the mean high water mark. Do not contaminate water when disposing of equipment washwater or rinsate. Ground Water: This product is known to leach through soil into groundwater under certain condi tions as a result of label use. This chemical may leach into groundwater if used in areas where soils are permeable, particularly where the water table is shallow. Surface Water: This product may impact surface water quality due to runoff of rain water. This is especially true for poorly draining soils and soils with shallow ground water. This product is classified as having high potential for reaching surface water via runoff for several months or more after application. A level, well-maintained vege tative buffer strip between areas to which this product is appli ed and surface water features such as ponds, streams, and springs will reduce the potential loading of flufenacet and its degradates from runoff water and sediment. Runoff of this product will be reduced by avoiding applications when rainfall or irrigation is expected to occur within 48 hours.

DIRECTIONS FOR USE It is a violation of Federal law to use this product in a manner inconsistent with its labeling. Do not apply this product in a way that will contact workers or other persons, either directly or through drift. Only protected handlers may be in the area during application . For any requirements specific to your State or Tribe, consult the ag ency responsible for pes ticide regulation. AGRICULTURAL USE REQUIREMENTS Use this product only in accordance with its labeling and with the Worker Protection Standard, 40 CFR part 170. This Standard contains requirements for the protection of agricultural workers on farms, forests, nurseries, and greenhou ses, and handlers of agricult ural pesticides. It contains requirements for training, decontamination, notification, and emergency assistance. It also contains sp ecific instructions and exceptions pertaining to the statements on t his label about personal protective equipment (PPE), and restricte d-entry interval. The requirements in this box only apply to uses of this product that are covered by the Worker Protection Standard. Do not enter or allow workers to enter during the restricted-entry interval (REI). The REI and exce ptions are listed in the Dir ections for Use associated with the crop. Notify workers of the exception (including when entry is permitted for each of the tasks named in the exception). Exception: If the product is soil-injecte d or soil- incorporated, the Worker Protection Standard, under certain circumstances, allows workers to enter the treated area if there will be no contact with anything that has been treated. PPE required for early entry to treated areas that is permitted under the Worker Protection Standard and that involves contact with anything that has been treated, such as plants, soil, or water, is: ƒ Coveralls ƒ Chemical-resistant gloves made of any waterproof material ƒ Shoes plus socks

4

PRODUCT INFORMATION FLUFENACET 4 SC HERBICIDE is a selective herbicide for control of many annual grasse s and certain broadleaf weeds in field corn , white corn, corn grown for silage, field corn grown for seed, sweet corn, and soybeans. FLUFENACET 4 SC HERBICIDE may be applied preplant surface, preplant incorporated (mix into the top 1 to 2 inch layer of soil) and preemergence and/ or early postemergenc e. FLUFENACET 4 SC HERBICIDE will provide its most effective weed control when applied and subseque ntly moved into the soil by rainfall, sprinkler irrigation or mechanical tillage prior to weed emergence. FLUFENACET 4 SC HERBICIDE may be applied using either water or sprayable fluid fertilizer as a liquid carrier. FLUFENACET 4 SC HERBICIDE may be applied either alone or in tank mix combination with additional herbicides. When tank mixing, always observe all precautionary statements and limitations on labeling of all products. Dry weather following preemergence application of FLUFENACET 4 SC HERBICIDE or recommended tank mixtures may reduce effectiveness. Cultivate if weeds develop.

USE RESTRICTIONS FLUFENACET 4 SC HERBICIDE is for use on field corn, white corn, corn grown for silage, field corn grown for seed, sweet corn, a nd soybean. Do not use on popcorn. Do not apply this product through any type of irrigation system. Do not apply aerially. Do not use flood irrigation to apply, activate or incorporate FLUFENACET 4 SC HERBICIDE. Do not apply more than 25 fluid ounces FLUFENACET 4 SC HERBICIDE per acre per year in corn and 14 ounces per acre per year in soybeans. Do not make a postemergence application of FLUFENACET 4 SC HERBICIDE to corn beyond the 5 th leaf collar growth stage (begin count with the 1st leaf-rounded tip). Do not harvest corn forage (silage) within 75 days after a postemergence application. Do not make a postemergence application of FLUFENACET 4 SC HERBICIDE to corn beyond the 5th leaf collar growth stage (begin count with the 1st leaf-rounded tip). Do not harvest corn forage (silage) within 75 days after a postemergence application. Corn and soybean seed should be planted a minimum of 1-1/2 inches deep. If any crop treated with FLUFENACET 4 SC HERBICIDE is lost, corn or soybeans may be replanted immediately. Do not make a second application of FLUFENACET 4 SC HERBICIDE. This product may not be mixed or loaded within 50 feet of any wells (including abandoned wells and drainage wells), sink holes, perennial or intermittent streams and rivers, and na tural or impounded lakes and reservoirs. This setback does not apply to properly capp ed or plugged abandoned wells and does not apply to impervious pad or properly diked mixing / loading areas. Operations that involve mixing, loading, rins ing, or washing of this product into or from pesticide handling or application equ ipment or containers within 50 feet of an y well are prohibited unless conduc ted on an impervious pad constr ucted to withstand the weight of the heaviest load that may be positioned on or moved across the pad. Such a pad shall be designed and maintained to contain any product spills or equipment leaks, container or equipment rinse or washwater, and rainwater that may fall on the pad. Surface water shall not be allowed to either flow over or from the pad, which means the pad must be self contai ned. The pad shall be sloped to facilitate material removal. An unroofed pad shall be of sufficient capacity to cont ain at a minimum 110% of the capacity of the largest pesticide container or application equipment on the pad. A pad that is covered by a roof of sufficient size to comple tely exclude precipitation fro m contact with the pad shall have a minimum containmen t capacity of 100% of the capacity of th e largest pesticide co ntainer or applicatio n equipment on the pad. Containmen t capacities as described above sh all be maintained at all time s. The above specific minimum containment capacities do not apply to v ehicles when delivering pesticide shipments to the mixing / loading site. States may h ave in effect additional requirements regarding wellhead setbacks and operational containment. This product must be used in a manner which will prevent back siphoning in wells, spills or improper disposal of excess pesticide, spray mixtures or rinsates.

SPRAY DRIFT

1. When using ground application equipment, apply with nozzle height no more than 4 feet above the ground or crop canopy.
2. Applicators are required to use Medium droplet size (ASABE SS72.l).
3. Do not apply when wind speeds exceed 10 miles per hour at the application site.
4. Do not apply during temperature inversions.

5

SPRAY DRIFT ADVISORIES

The interaction of many equipm ent and weather-related factors determines the potential for spra y drift. The applicator is responsible for considering all these factors when making application decisions.

IMPORTANCE OF DROPLET SIZE The most effective way to reduce drift pote ntial is to apply large drople ts. The best drift management strategy is to apply the largest droplets that provide sufficient coverage and control. The presence of se nsitive species nearby, the environmental conditions, and pest pressure may affect how an applicator balances drift control and coverage. APPLYING LARGER DROPLETS REDUCES DRIFT POTENTIAL, BUT WILL NOT PREVENT DRIFT IF APPLICATIONS ARE MADE IMPROPERLY OR UNDER UNFAVORABLE ENVIRONMENTAL CONDITIONS! See Wind, Temperature and Humidity, and Temperature Inversions sections of this label.

Controlling Droplet Size x Volume - Use high flow rate nozzles to apply the highest prac tical spray volume . Nozzles with higher rated flows produce larger droplets. x Pressure - Use the lower spray pressures recommended for th e nozzle. Higher pressure reduces droplet size and does not improve canopy penetration. WHEN HIGHER FLOW RATES ARE NEEDED, USE A HIGHER- CAPACITY NOZZLE INSTEAD OF INCREASING PRESSURE. x Nozzle Type - Use a nozzle type that is designed for the intended application. With most nozzle types, narrower spray angles produce larger droplets. Consider using low-drift nozzles.

BOOM HEIGHT Setting the boom at the lowest referenced height (if specified) which provides uniform coverage reduces the exposure of droplets to evaporation and wind. For ground equipment, the boom should remain level with the crop and have minimal bounce.

WIND Drift potential increases at wind speeds of less than 3 mph (due to inversion potential) or more than 10 mph. However, many factors, including droplet size and equipment type determine drift potential at any given wind speed. AVOID APPLICATIONS DURING GUSTY OR WINDLESS CONDITIONS. Note: Local terrain can influence wind patt erns. Every applicator should be familiar with local wind patterns and how they affe ct spray drift.

TEMPERATURE AND HUMIDITY When making applications in hot and dry conditions, set up equipment to produce larger droplets to reduce effects of evaporation.

TEMPERATURE INVERSIONS Drift potential is high during a temperature inversion. Temper ature inversions restrict vertic al air mixing, which causes small suspended droplets to remain close to th e ground and move laterally in a concentrated cloud. Temperature inversions are characterized by increasing temperature with altitude and are common on nights with lim ited cloud cover and light to no wind. They begin to form as the sun sets and often continue into the morning. Their presence can be indicated by ground fog; however, if fog is not present, inversions can also be identified by the movement of smoke from a ground so urce or an aircraft smoke generator. Smoke that layers and moves laterally in a concentrated cloud (under low wind conditions) indicates an inversion, while smoke that moves upward and rapidly dissipates indicates good vertical air mixing.

SHIELDED SPRAYERS Shielding the boom or individual nozzles can reduce the effects of wind. However, it is the responsibility of the applicator to verify that the shields are preventing drift and not interfering with uniform deposition of the product.

POLLINATOR ADVISORY STATEMENT This product contains an herbicide, therefore follow all label directions and precautions to minimize potential off-target exposure in order to prevent effects to non-target plants adjacent to the treate d site which may serve as habitat or forage for pollinat ors, including monarch butterflies (and larvae), birds, and bats.

RESISTANCE MANAGEMENT FLUFENACET 4 SC HERBICIDE is a Group 15 Herbicide (inhibition of very long chain fatty acids). A given weed population may contain or develop resistance to a herbicide after repeated use. Appropriate resistance-management strategies should be followed to mitigate or delay resistance. The following Integrated Weed Management Techniques are effective in reducing problems with herbicide resistant weed biotypes. It is best to use multiple practices to manage or delay resistance, as no single strategy is likely to be totally effective.

x Rotate crops. Crop rotation diversifies weed management. x Rotate herbicide-tolerant traits. Alternate herbicide-tolerant (HT) traits and/or use HT trait stacks for more efficient rotation.

6

x Use multiple herbicide sites of action. Use tankmix partners and multiple SOAs during both the growing season and from year to year to reduce the selection pressure of a single SOA. x Know your weeds, know your fields. Closely monitor problematic areas with difficult-to-control weeds or dense weed populations. x Start with clean fields. Effective tillage or the use of a burndown herbicide program can control emerged weeds prior to planting. x Stay clean – use residual herbicides. Regardless of tillage system, pre-emergence or early post-emergence soil-applied residual herbicides should be used when possible. x Apply herbicides correctly. Ensure proper application, including timing, full use-rates and appropriate spray volumes. x Control weed escapes. Consider spot herbicide applications, row wicking, cultivation or hand removal of weeds or other techniques to stop weed seed production and improve weed management. x Zero tolerance – reduce the seed bank. Do not allow surviving weeds to set seed, which will help decrease weed populations from year to year and prevent major weed shifts. x Clean equipment. Prevent the spread of herbicide-resistant weeds and their seeds.

Contact your local extension specialist, certified crop advisory and /or Bayer CropScience representative for additional resistance management or IPM recommendation. Also for more information on Weed Resistance Management, visit the Herbicide Resistance Action Committee (HRAC) on the web at http://www.hracglobal.com.

RATE SELECTION/SOIL TEXTURE The application rates of FLUFENACET 4 SC HERBICIDE are determined by texture and organic matter content of the soil being treated. Unless a specific soil texture is mentioned, rate tables throughout this label refer to the following three soil texture groups: coarse, medium and fine. If you are not sure how to classify your soil, contact your Bayer Corporation representative, the Cooperative Extension Service or other knowledgeable person. The foll owing chart includes a co mplete listing of soil textures included in each of the soil te xtures groupings:

COARSE MEDIUM FINE Sand Loamy sand Sandy loam Loam Silt loam Silt Sandy clay loam Sandy clay Silty clay loam Silty clay Clay loam Clay MIXING INSTRUCTIONS LIQUID CARRIERS: FLUFENACET 4 SC HERBICIDE is a flowable herbicide that must be mixed in water or sprayable f luid fertilizer. Compatibility of FLUFENACET 4 SC HERBICIDE or its labeled tank mix products with these liquid carriers should always be determined prior to spraying. Refer to the SPRAYABLE FLUID FERTILIZER COMPATIBILITY TEST (App endix I) of this label to determine product compatibility in fluid fertilizer carriers. Before mixing FLUFENACET 4 SC HERBICIDE and its labeled tank mixtures, examine the spray equipment making sure it is completely clean and free of rust or corrosion. Be sure the equipment is free of any residues from previously used pesticides. Flush lines with clean water or recommended detergents after the last application. Use an approved method for disposing of rinsate. For optimum spray tank mixing and efficacy, FLUFENACET 4 SC HERBICIDE is recommended to be added to the spray tank via an eductor system. The proper mixing sequence for FLUFENACET 4 SC HERBICIDE and recommended tank mixtures with the appropriate liquid carrier is as follows:

1. Fill the spray tank or nurse tank 1/4 full with the appropriate liquid carrier.
2. Start recirculation and agitation system and continue throughout mixing and application.
3. If the compatibility test in dicates the need of a compatibility agent, add the recommended amount of compatibility agent to the spray tank.
4. If ammonium sulfate is to be used, add it now.
5. Next add the specified quantity of F LUFENACET 4 SC HERBICIDE through the educ tor or to the spray tank [slowly add FLUFENACET 4 SC HERBICIDE if water or sprayable grade nitrogen fertilizers (28-0-0, 32-0-0) are the carriers; for other sprayable grade fertilizers first check compatibility and then either mix directly or preslurry in water depending in the results of the compatibility test].
6. If tank mixing with wettable powders or dry fl owable products in water, they may be added now.

7

If tank mixing these products in a sprayable fertilizer carrier, first make a slurry of the products with water and then add t he slurry slowly to the spray tank. 7. If tank mixing with emulsifiable concentrates or soluble products, add the products to the spray tank. 8. If tank mixing with a glyphosate-co ntaining product or Touchdown®, add the products to the spray tank. 9. If mixing spray adjuvants in the mixture, ad d them after all other products have been mixed. 10. Fill the spray tank to the desired level with the appropriate liquid carrier. 11. Continue agitation during transport and application until the spray tank is empty. FLUFENACET 4 SC HERBICIDE and all registered mixtures should be kept agitated once mixed and then sprayed immediately. Do not allow mixtures to stand for prolonged periods of time. Water quality, pH, temperature and/or other components of the mixture may affect how long the mixture may stand before application.

APPLICATION INFORMATION SPRAYER APPLICATION Ground Broadcast Treatment: Accurately calibrate the sprayer prior to mixing the herbicide treatments. Apply FLUFENACET 4 SC HERBICIDE and the labeled tank mixtures in a minimum of 10 gallons of total spray volume per acre using broadcast boom equipment. Use a pump with capacity to ma intain 30 to 40 psi at the no zzles, maintain adequate in-tank agitation to keep the spray mixture in suspension and provide a minimum of 20% bypass at all times. If mixed with other labeled herbicides, the spray volume may be no less than the minimum volume specified by the tank mix product or 10 gallons, whichever is greater. The use of screens to protect the pump and nozzles is recommended. Screens placed on the suction side of the pump should be 16-mesh or coarser. Do not place a screen in the recirculation line. Use 50-mesh or coarser screens between the pump and boom, and where required, at the nozzles. Refer to the nozzle manufacturer for additional recommendations. Agitate thoroughly before and during application with either bypass or mechanical agitation. Rinse the sprayer thoroughly with clean water immediately after each use. Band Treatment: FLUFENACET 4 SC HERBICIDE and the labeled tank mixtures may be applied as a band treatment. Use the following formula to calculate the amount of herbicide needed for band treatments: Band width in inches X Broadcast rate = Band rate Row width in inches per acre per acre APPLICATION METHODS AND TIMING FLUFENACET 4 SC HERBICIDE may be applied eith er alone or in tank mixtur es with or sequentially with certain other registered an d recommended herbicides. Applicatio ns may be made preplant surface, preplant in corporated or preemergence. FLUFENACET 4 SC HERBICIDE may be used in either a single or split application program. Preplant Surface: For use in conservation, minimum or no- tillage crop production systems, FLUFENACET 4 SC HERBICIDE alone or as a recommended tank mixture may be applied as a broadcast spray up to 45 days before planting in corn and 14 days before planting in soybeans. A split application is recommended for applications made 30 to 45 days prior to planting, where 2/3 of the highest specified broadcast rate for the crop and soil texture is applied initially and the remaining 1/3 is applied at planting. Treatments made less than 30 days before planting may use either a single or split application. If weeds are present at the time of application, apply the FLUFENACET 4 SC HERBICIDE treatment in tank mixture wi th a recommended nonselective foliar herbic ide. If possible, do not move treated soi l out of the row or move untreated soil to the soil surface prior to or during planting, as weed control may be reduced. Preplant Incorporation: Apply FLUFENACET 4 SC HERBICIDE alone or in combination with recommended tank-mixes as a broadcast spray and incorporate into the up per 1 to 2 inches of the soil surface up to 14 days before plan ting. Avoid deep incorporation since reduced weed control and/or crop injury may result. Incorporate with implements which provide uniform, shallow incorporation (example -finishing disk, harrow, rolling cultivator, etc.) Preemergence: FLUFENACET 4 SC HERBICIDE alone and its recommended tank mixes may be applied to the soil surface as a broadcast spray or band application after pla nting of the crop but prior to weed or cro p emergence. If weeds are present at the time of application, apply FLUFENACET 4 SC HERBICIDE with a nonselectiv e foliar herbicide. Rainfall and/or overhead sprinkler irrigatio n is necessary to move FLUFENACET 4 SC HERBIC IDE into the upper soil surface where we ed seeds germinate. Dry weather conditions following application may reduce weed control. If adequate mois ture is not received within 7 to 10 days after applications and weeds begin to emerge from the soil, a light rotary hoeing or shallow incorporation (no deeper than 1/2 inch deep) will improve performance and minimize crop damage. Excessive rainfall or irrigation after application may reduce weed control. Early Postemergence: When used as an early postemer gence treatment, FLUFENACET 4 SC HE RBICIDE may be applied once per year alone or in combination with or sequentially with certain herbicides. Use of an adjuvant is recommended in some applications. Refer to crop sections of the label for specific information. Special Applications: Fall Application (for use only in IA, MN, ND, SD, WI, north of Route 20 in NE, north of Route 136 in IL, and north of Interstate 70 in OH): Following harvest of crops in the fall, F LUFENACET 4 SC HERBICIDE may be applied to crop stubble after Oc tober 15, when the sustained soil temperature at the four-inch soil depth is less than 50o F, but before the ground is frozen. This application is limited to only medium- and fine-textured soils with an organic matter of 2.5% or greater and which will be planted to corn the following spring. The soil may be tilled before or after application with incorporation dept h no more than two to three in ches following herbicide applica tion. If a

8

spring application of FLUFENACET 4 SC HERBICIDE follows the fall application, the total FLUFENACET 4 SC HERBICIDE rate for both applications must not exceed 25 fluid ounces. CORN (Field, Seed, and Sweet) FLUFENACET 4 SC HERBICIDE flowable herbicide is a selective he rbicide for control of most annual grasses and selected annual broadleaf weeds in corn. A maximum of two applications may be made alone or in tank-mix combination with certain registered herbicides. The following types of applications are allowe d: preplant surface, preplant incorporat ed and preemergence and early postemergence. Most effective weed control will occur when the applied product is moved into the soil by rainfall, sprinkler irrigation or mechanical tillage prior to weed emergence from the soil. For post-emergent use in Corn: The REI is 23 days. Exception: In addition to the early entry exceptions allowed by the Worker Protection Standard, you may enter or allow workers to enter treated areas to scout 3 days following application as long as the worker wea rs long pants, long sleeved shirt and shoes plus socks. Special Precautions: Field seed corn inbred lines and sweet corn varieties may vary in th eir response to FLUFENACET 4 SC HERBICIDE. Do not apply FLUFENACET 4 SC HERBICIDE to inbreds without first verifying with your local seed corn company (supplier) the FLUFENACET 4 SC HERBICIDE selectivity on your inbred line.

9

WEED SPECIES CONTROLLED BY FLUFENACET 4 SC HERBICIDE Flufenacet 4 SC Herbicide applied at specified dosages and application timings will control many important annual grasses and broadleaf weeds.

WEEDS CONTROLLED ANNUAL GRASS WEEDS Barnyardgrass Crabgrass, large Crabgrass, smooth Foxtail, giant Foxtail, green Foxtail, yellow Goosegrass Johnsongrass (seedling) Lovegrass, India Panicum, browntop Panicum, fall Signalgrass, broadleaf Witchgrass ANNUAL BROADLEAF WEEDS Carpetweed Purslane, common Pusley, Florida Spurge, spotted WEED SPECIES PARTIALLY CONTROLLED BY FLUFENACET 4 SC HERBICIDE Flufenacet 4 SC Herbicide will provide partial control or reduced competition for many additional grass and broadleaf weeds. Re duced competition weeds will be stunted in growth and/or be of reduced populations as compared to non-treated areas but control will generally not be commercially acceptable.

WEED SPECIES PARTIALLY CONTROLLED ANNUAL GRASS/SEDGE WEEDS Cupgrass, woolly Millet, wild-proso Nutsedge, yellow Panicum, Texas Sandbur, field Shattercane ANNUAL BROADLEAF WEEDS Beggarweed, Florida Lambsquarters, spp. Mustard spp. Nightshade, eastern black Pigweed spp. Ragweed, common Sida, prickly Waterhemp, common Waterhemp, tall FLUFENACET 4 SC HERBICIDE USE RATES IN FALL, PREPLANT SURFACE, PREPLANT INCORPORATED AND PREEMERGENCE APPLICATIONS AND EARLY POSTEMERGENCE For FALL Application ( For use only in IA, MN, ND, SD, WI, north of Rout e 20 in NE, north of Rout e 136 in IL, and north of Interstate 70 in OH): After October 15, when the susta ined soil temperature at the four inch soil depth is less than 50 o F, FLUFENACET 4 SC HERBICIDE may be applied to remaining crop stubble following harvest. In conservation, minimum and no-tillage systems on soils having 2.5% organic matter or greater, apply FLUFENACET 4 SC HERBICIDE at 23 to 25 fluid oz/A on medium textured soils and 25 fluid oz/A on fine textured soils. Apply before the ground is frozen. The soil may be tilled before or after application with an incorporation depth no more than two to three inches following the fall application. Minimize furrow and ridge formation in the tillage operations after application of FLUFENACET 4 SC HERBICIDE. If a spring application is made, the total rate of both fall and spring must not exceed the maximum total rate for corn, or illegal residues may occur. For CONVENTIONAL Tillage Systems With Applications Made TW O WEEKS OR LESS Preplant Surface, Preplant Incorporated or Preemergence: FLUFENACET 4 SC HERBICIDE use rates are located in Table 1. Rates are based on soil texture and organic matter and are for applications made within two weeks of planting and until corn emergence. Do not use on peat or muck soils (soils with 20% or more organic matter).

10

TABLE 1 FLUFENACET 4 SC HERBICIDE USE RATES IN CONVENTIONAL TILLAGE APPLICATIONS MADE TWO WEEKS OR LESS PREPLANT SURFACE, PREPLANT INCORPORATED OR PREEMERGENCE. FLUFENACET 4 SC HERBICIDE RATE (FL. OZ. PER ACRE)1 SOIL TEXTURAL GROUP 2 SOIL ORGANIC MATTER CONTENT Less than 3% 3% or More COARSE 15 fl oz 17 fl oz MEDIUM 17 to 19 fl oz 19 to 22 fl oz FINE 22 to 24 fl oz 22 to 25 fl oz 1 Use the higher rate of FLUFEN ACET 4 SC HERBICIDE within the applicable rate range under any of the following conditions: heavy surface plant residues, heavy weed pressure and/or when soil organic matter is at the upper end of the range. 2 For more information, refer to the "Rate Selection/Soil Texture" section of this label. For CONSERVATION, MINIMUM, and NO-TILLAGE Systems; or CONVENTIONAL Tillage Systems With Applications GREATER THAN TWO WEEKS Preplant: FLUFENACET 4 SC HERBICIDE use rates are located in Table 2. Rates are higher for these types of tillage systems and application timings than in Table 1 due to the extended period of weed control needed and the increased crop residue present. Refer to the “Application Methods and Timing” section of the label for details. Weed control will generally be greater the closer the applications are made to planting but prior to weed emergence. If weeds ar e present at application, a nonselective herbicide such as a glyphosate-containing product or Touchdown used at specified rates may be mixed with FLUFENACET 4 SC HERBICIDE treatments. Do not use on peat or muck soils (soils with 20% or more organic matter).

TABLE 2 FLUFENACET 4 SC HERBICIDE USE RATES IN CONSERVATION, MINIMUM, AND NO-TILLAGE SYSTEMS; OR CONVENTIONAL TILLAGE SYSTEMS WITH APPLICATIONS GREATER THAN TWO WEEKS PREPLANT SURFACE. FLUFENACET 4 SC HERBICIDE RATE (FL. OZ. PER ACRE)1 SOIL TEXTURAL GROUP2 SOIL ORGANIC MATTER CONTENT Less than 3% 3% or More COARSE 16 fl oz 18 fl oz MEDIUM 19 to 22 fl oz 22 to 24 fl oz FINE 24 to 25 fl oz 24 to 25 fl oz 1 Use the higher rate of FLUFENACET 4 SC HERBICIDE within the applicable rate range under any of the following conditions: heavy surface plant residues, heavy weed pressure an/or when soil organic matter is at the upper end of the range. 2 For more information, refer to the "Rate Selection/Soil Texture" section of this label.

FOR EARLY POSTEMERGENCE APPLICATIONS: FLUFENACET 4 SC HERBICIDE Flowable Herbicide use rates are located in Table 1. FLUFENACET 4 SC HERBICIDE alone and/or certain FLUFENACET 4 SC HERBICIDE tank mixtures ma y be applied to corn from emergence through the 5 th leaf collar growth stage. Begin le af count with the first leaf (rounde d tip). FLUFENACET 4 SC HERBICIDE alone will not provide control of emerged weeds. For control of emerged weeds, FLUFENACET 4 SC HERBICIDE may be tank mixed with approved postemergence herbicides. Read and follow all precautions/restrictions and directions on tank mix partner labels. Corn treated with FLUFENACET 4 SC HERBICIDE early postemergence may be harvested for forage (silage) 75 days or more after treatment. Adjuvants for early postemergence: The adjuvant types listed below may be utilized with FLUFENACET 4 SC HERBICIDE Flowable Herbicide. UAN (urea ammonium nitrate) is commonly refe rred to as 28, 30, or 32%N. UAN can be used as an adjuvant in certain herbicide tan k mixtures with FLUFENACET 4 SC HERBICIDE, or as a spray carrier for FLUFENACET 4 SC HERBICIDE. Fluid fertilizers applied after crop emergence can result in crop tissue “burn” symptoms. Using fluid fertilizer as a postemergence spray carrier to apply FLUFENACET 4 SC HERBICIDE is not recommended if fluid fertilizer burn is not considered acceptable. Ammonium sulfate (spray grade) is recommended as an alternative to UAN as a spray solution adjuvant with certain tank mixture partners. When tank mixing FLUFENACET 4 SC HERBICIDE Flowable Herbicide with other herbicides be certain to select adjuvants recommended and compatible for use with all herbicides included in the tank mixture.

11

FLUFENACET 4 SC HERBICIDE TANK MIXTURES FLUFENACET 4 SC HERBICIDE may be applied in tank mixture with cert ain herbicides to improve control of broadleaf weeds such as velvetleaf, common cocklebur and morningglory species provided that the other herbicide is registered on soybeans and that the tankmix product does not prohibit such mixing. Mixtures may be used in either conventional, conservation, minimum and no-tillage systems. They may be applied with similar timings and methods as FLUFENACET 4 SC HERBICIDE alone unless specif ically prohibited in the mix partner’s product label. Three-way or multiple tank mixtures are permitted unless restricted by the product label. Refer to the individual product labels for specified use rates, precautions and/or restrictions. The following herbicides may be tank-mixed with FLUFENACET 4 SC HERBICIDE provided the product to be tank-mixed is registered for use on this site. Herbicides recommended for tank mixtures with FLUFENACET 4 SC HERBICIDE include: Atrazine Axiom Balance® Balance Pro® Banvel® Clarity® Epic Glyphosate Hornet® Prowl® Python® Marksman® Eradicane® Roundup® Roundup Ultra® 2,4-D Sencor® Touchdown®

FLUFENACET 4 SC HERBICIDE SEQUENTIAL APPLICATIONS Sequential herbicide applications either before or following FLUFENACET 4 SC HERBICIDE treatments may be used to control additional weeds. Herbicides recommended for sequential applications include: Atrazine Accent® Accent® Gold Aim® Balance® Balance Pro® Banvel® Basagran® Basis® Basis Gold® Battalion® Beacon® Bromoxynil Bromoxynil +Atrazine Buctril® Buctril® + Atrazine Buctril® Gel Callisto® Clarity® Distinct® Exceed® Glyphosate Hornet® Liberty® Lightning® Marksman® Northstar® Permit® Poast® Prowl® Pursuit® Python® Resolve® Resource® Roundup® Roundup Ultra® Scorpion III® Sencor® Spirit® Touchdown® 2,4-D

Refer to the above tank mixture and sequential application information and the individual product labels for use directions, use rates and special precautions/restrictions. SOYBEAN FLUFENACET 4 SC HERBICIDE is a selective herbicide for control/suppression of most annual grasses in soybeans. FLUFENACET 4 SC HERBICIDE may be applied once per year either alone, in tank mix combination with or sequentially with certain registered herbicides. The following types of application are allowed: preplant surface, preplant incorporated and pree mergence. The preplant surface and preplant incorporated treatments may be applied up to 14 days before planting. The mo st effective weed control will occur when the applied product is moved into the soil by rainfall, sprinkler irrigation or mechanical tillage prior to weed emergence form the soil. Do not graze or feed forage, hay or straw to livestock.

For post-emergent use, do not enter or allow worker entry into treated areas during the restricted entry interval (REI) of 13 days.

12

WEED SPECIES CONTROLLED BY FLUFENACET 4 SC HERBICIDE Flufenacet 4 SC Herbicide applied alone at the specified dosages and application timings will provide control of certain annual grasses. WEEDS CONTROLLED1 ANNUAL GRASS WEEDS Barnyardgrass Crabgrass, large Crabgrass, smooth Foxtail, giant Foxtail, green Foxtail, yellow Goosegrass Lovegrass, India Panicum, fall 1 Full season weed control will be achiev ed only on coarse textured soils using the maximum 14 ounce use rate. Use rates of 8 to 14 ounces will provide only early season weed control on all other soil textures. To complement early season w eed control, FLUFENACET 4 SC HERBICIDE is recommended for use in tank-mixture with or sequentially with other herbicides that provide additional control of these weed species.

WEED SPECIES PARTIALLY CONTROLLED BY FLUFENACET 4 SC HERBICIDE Flufenacet 4 SC Herbicide will provide partial control or reduced competition for additional annual grasses. Reduced competition weeds will be stunted in growth and/or be of reduced populations as compared to non-treated areas but control will generally not be commercially acceptable. WEED SPECIES PARTIALLY CONTROLLED ANNUAL GRASS WEEDS Johnsongrass, seedling Panicum, browntop Sandbur, field Signalgrass, broadleaf Shattercane Witchgrass

FLUFENACET 4 SC HERBICIDE USE RATES The use rates for FLUFENACET 4 SC HERBICIDE applied alone, in tank mix combination with and/or sequentially with other herbicides for all application methods and timings is 8 to 14 fluid ounces per acre. The 14 fluid ounce rate of FLUFENACET 4 SC HERBICIDE will provide full season control of annual grasses in coarse textured soils but will provide only early season weed control on medium and fine textured soils. Rates lower than 14 fluid ounces will provide only early season weed control on all soil textures. To complement this early season weed control, FLUFENACET 4 SC HERBICIDE should be used in tank-mixture or sequentially with other herbicides that provide additional control of these weed species.

FLUFENACET 4 SC HERBICIDE TANK MIXTURES FLUFENACET 4 SC HERBICIDE may be applied in tank mixture with certain herbicides to improve co ntrol of annual grasses and/or broadleaf weeds such as velvetle af, common cocklebur and morningglory species provided that the other herbicide is registered o n soybeans and that the tankmix product does not prohibit such mixing. Mixtures may be used in either conventional, conservation, minimum and no-tillage systems. They may be appl ied with similar timings and methods as FLUFENACET 4 SC HERBICIDE alone unless specifically prohibited in the mix partner product label. Three-way or multiple tank mixtures are permitted unless restricted b y the mix partner product labels. Refer to the individual product labels for use rates, precautions and/or restrictions. The following herbicides may be tank-mixed with FLUFENACET 4 SC HERBICIDE provided the product to be tank-mixed is registered for use on this site. Herbicides recommended for tank mixtures with FLUFENACET 4 SC HERBICIDE include:

Authority Broadleaf® Canopy® Canopy XL® Classic® DF Command® FirstRate® Gauntlet® Glyphosate Linuron (Lorox® and others) Prowl® Pursuit® Roundup® Roundup Ultra® Scepter® Sencor® (Metribuzin) Sonolan HFP® Touchdown® Trifluralin

13

FLUFENACET 4 SC HERBICIDE SEQUENTIAL APPLICATIONS Sequential herbicide applications may be used in a FLUFENACET 4 SC HERBICIDE weed control program to control additional weeds. Herbicides recommended for use either before or following FLUFENACET 4 SC HERBICIDE treatments include: Assure II® Basagran® Canopy® Classic® Cobra® Command® Concert® FirstRate® Flexstar® Fusilade® Fusion® Galaxy® Glyphosate Liberty® Linuron Option II® Pinnacle® Poast® Poast Plus® Prowl® Pursuit® Raptor® Reflex® Reliance STS® Resource® Roundup® Roundup Ultra® Scepter® Select® Sencor® Sonalan HFP® Storm® Synchrony STS® Tornado® Touchdown® Trifluralin 2,4-D

Refer to the above tank mixture and sequential application information and the individual product labels for use directions, use rates and special precautions/restrictions.

CORN AND SOYBEAN CROP ROTATION INSTRUCTIONS In the event of a crop failure any crop on this label can be replanted immediately. Do not make a second application of FLUFENACET 4 SC HERBICIDE. Do not graze or feed to livestock the forage or fodder of cotton planted 5 months after a FLUFENACET 4 SC HERBICIDE application. Waiting period after Flufenacet 4 SC Herbicide application before the following crops can be planted.

Immediately Corn Soybean 1 month Potato 4 months Cabbage Carrots Cotton Lettuce Peppers Radish Sugar beets All other leafy vegetables 12 months Alfalfa Barley Bermudagrass Bluegrass Bromegrass Buckwheat Clover Fescue Millet, pearl Millet, prose Oats Popcorn Rice Rye Sorghum Teosinte Triticale Wheat Wild Rice All other crops

14

APPENDIX I SPRAYABLE FLUID FERTILIZER COMPATIBILITY TEST A compatibility test is highly recommended for all applications with liquid fertilizers. Prior to mixing products in the spray tank, small quantities of each product can be mixed in proportionate quantities to evaluate compatibilities. The following test assumes a spray volume of 25 gallons per acre. If other spray volumes are to be used, adjust the appropriate amounts of ingredients. To check for comp atibility, use the following procedure:

1. Add two inches of the liquid carrier (water or liquid fertilizer) to a one-quart jar fitted with a tight lid.
2. Add the appropriate amount of herbicide. If more than one product is used, the recommended mix sequence is the dry herbicide first, flowables next and emulsified concentrates last. For dry herbicides, add 1-1/2 level teaspoons/pound/acre use rate and for liquids add 1/2 teaspoon/pint/acre use rate.
3. Add one pint of the li quid carrier (water or liquid fertilizer) to the jar. Place the lid on the jar and gently shake the jar for one minute. Place the jar on a level surface and let it stand for 30 minutes.
4. Reagitate the mixture and observe the mi xture for signs of phase separation, flakes , particles, gels, precipitates, etc. If none of these conditions occur, the mix is compatible.
5. If incompatible, use of a compatibilit y agent is recommended. Rerun the above test but first add a compatibility agent (1/4 teaspoon is equal to a use rate of 2 pints/100 gallons spray mix) and gently shake the jar prior to adding herbicides.
6. If the mixture is now compatible, a compatibility agent should be used in the spray mixture at its recommended rate.
7. If the components of the solution are still incompatible, the mixture should not be attempted for use in the spray tank.
8. Contact your Bayer representative for further reco mmendations on testing spray solution compatibilities.

15

STORAGE AND DISPOSAL Do not contaminate water, food or feed by storage or disposal. PESTICIDE STORAGE: Store in a cool, dry place and in such a manner as to prevent cross contamination with other pesticides, fertilizers, food, and feed. Store in original container and out of the reach of children, preferably in a locked storage area. Handle and open container in a manner as to prevent spillage. If the container is leaking, invert to prevent leakage. If container is leaking or material spilled for any reason or cause, carefully dam up spilled material to prevent runoff. Refer to Precautionary Statements on label for hazards associated with the handling of this material. Do not walk through spilled material. Absorb spilled material with absorbing type compounds and dispose of as directed for pesticides below. In spill or leak incidents, keep unauthorized people away. PESTICIDE DISPOSAL: Wastes resulting from the use of t his product may be disposed of on site or at an approv ed waste disposal facility.

[Non-Seed Treatment Products in Non-Refillable Containers]

Rigid, Non-refillable containers (equal to or less than 5 gallons) Non-refillable container. Do not reuse or refill this container. Triple rinse or pressure rinse container (or equivalent) promptly after emptying. Triple rinse as follows: Empty the remaining contents into application equipment or a mix tank and drain for 10 seconds after the flow begins to drip. Fill the container 1/4 full with water and recap. Shake for 10 seconds. Pour rinsate into application equipment or a mix tank or store rinsate for later use or disposal. Drain for 10 seconds after the flow begins to drip. Repeat this procedure two more times.

Pressure rinse as follows: Empty the remaining contents into application equipment or a mix tank and continue to drain for 10 seconds after the flow begins to drip. Hold container upside down over application equipment or mix tank or collect rinsate for later use or disposal. Insert pressure rinsing nozzle in the side of the container, and rinse at about 40 PSI for at least 30 seconds. Drain for 10 seconds after the flow begins to drip.

Once container is rinsed, offer for recycling if available or puncture and dispose of in a sanitary landfill or by incineration.

Rigid Non-refillable Containers that are too large to shake (i.e., with capacities greater than 5 gallons or 50 lbs) Non-refillable container. Do not reuse or refill this container. Refer to Bottom Discharge IBC or Top Discharge IBC, Drums, Kegs information as follows.

Bottom Discharge IBC (e.g. – Schuetz Caged IBC or Snyder Square Stackable) Pressure rinsing the container before final disposal is the responsibility of the person disposing of the container. To pressure rinse the container before final disposal, empty the remaining contents from the IBC into application equipment or mix tank. Raise the bottom of the IBC by 1.5 inches on the side which is opposite of the bottom discharge valve to promote more complete product removal. Completely remove the top lid of the IBC. Use water pressurized to at least 40 PSI to rinse all interior portions. Continuously pump or drain rinsate into application equipment or rinsate collection system while pressure rinsing. Continue pressure rinsing for 2 minutes or until rinsate becomes clear. Replace the lid and close bottom valve. Top Discharge IBC, Drums, Kegs (e.g.– Snyder 120 Next Gen, Bonar B120, Drums, Kegs) Triple rinsing the container before final disposal is the responsibility of the person disposing of the container. To triple rinse the container before final disposal, empty the remaining contents from this container into application equipment or mix tank. Fill the container at least 10 percent full with water. Agitate vigorously or recirculate water with the pump for 2 minutes. Rinse all interior surfaces. Pour or pump rinsate into application equipment or rinsate collection system. Repeat this procedure two more times.

Top Discharge IBC, Drums, Kegs (e.g.– Snyder 120 Next Gen, Bonar B120, Drums, and Kegs) Triple rinsing the container before final disposal is the responsibility of the person disposing of the container. To triple rinse the container before final disposal, empty the remaining contents from this container into application equipment or mix tank. Fill the container at least 10 percent full with water. Agitate vigorously or recirculate water with the pump for 2 minutes. Rinse all interior surfaces. Pour or pump rinsate into application equipment or rinsate collection system. Repeat this procedure two more times.

Once container is rinsed, offer for recycling if available or puncture and dispose of in a sanitary landfill or by incineration.

Non-Seed Treatment Products in Non-Refillable Fiber Drums with Liners Non-refillable container. Do not reuse or refill this container. Completely empty liner by shaking and tapping sides and bottom to loosen clinging particles. Empty residue into application equipment, then offer for recycling if available or dispose of in a sanitary landfill or by incineration. If drum is contaminated and cannot be reused, dispose of it in the manner required for its liner.

Non-Seed Treatment Products in Non-Rigid, Non-refillable Containers Nonrefillable container. Do not reuse or refill this container. Completely empty container into application equipment. Then offer for recycling if available or dispose of in a sanitary landfill or by other procedures approved by state and local authorities."

16

[Non-Seed Treatment Products in Refillable Containers]

Refillable container. Refer to Bottom Discharge IBC or Top Discharge IBC, Drums, Kegs information as follows. Refill this container with pesticide only. Do not reuse this container for any other purpose. Contact your Ag retailer or Bayer CropScience for container return, disposal and recycling information.

Bottom Discharge IBC (e.g. – Schuetz Caged IBC or Snyder Square Stackable) Pressure rinsing the container before final disposal is the responsibility of the person disposing of the container. Cleaning before refilling is the responsibility of the refiller. To pressure rinse the container before final disposal, empty the remaining contents from the IBC into application equipment or mix tank. Raise the bottom of the IBC by 1.5 inches on the side which is opposite of the bottom discharge valve to promote more complete product removal. Completely remove the top lid of the IBC. Use water pressurized to at least 40 PSI to rinse all interior portions. Continuously pump or drain rinsate into application equipment or rinsate collection system while pressure rinsing. Continue pressure rinsing for 2 minutes or until rinsate becomes clear. Replace the lid and close bottom valve.

Top Discharge IBC, Drums, Kegs (e.g.– Snyder 120 Next Gen, Bonar B120, Drums, Kegs) Triple rinsing the container before final disposal is the responsibility of the person disposing of the container. Cleaning before refilling is the responsibility of the refiller. To triple rinse the containers before final disposal, empty the remaining contents from this container into application equipment or mix tank. Fill the container at least 10 percent full with water. Agitate vigorously or recirculate water with the pump for 2 minutes. Rinse all interior surfaces. Pour or pump rinsate into application equipment or rinsate collection system. Repeat this procedure two more times.

Once container is rinsed, offer for recycling if available or puncture and dispose of in a sanitary landfill or by incineration.

End users are authorized to remove tamper-evident cables as required to remove the product from the container unless the container is equipped with one-way valves and refilling or returning is planned. If this is the case, end-users are not authorized to remove tamper- evident cables, remove one-way valves, or clean container.

17

IMPORTANT: READ BEFORE USE Read the entire Directions for Use, Condit ions, Disclaimer of Warranties and Limitation s of Liability before using this product . If terms are not acceptable, return the unopened product container at once. By using this product, user or buyer accepts the following Conditions, Disclaimer of Warranties and Limitations of Liability. CONDITIONS: The directions for use of this product are believed to be adequate and must be followed carefully. However, it is impossible to eliminate all risks associated with the use of this product. Crop injury, ineffectiveness or other unintended consequences may result because of such factors as weather conditions, presence of other materials, or the manner of use or application, all of which are beyond the control of Bayer CropScience. All such risks shall be assumed by the user or buyer. DISCLAIMER OF WARRANTIES: TO THE EXTENT CONSISTENT WITH APPLICABLE LAW, BAYER CROPSCIENCE MAKES NO OTHER WARRANTIES, EXPRESS OR IMPL IED, OF MERCHANTABILITY OR OF FITNESS FOR A PARTICULAR PURPOSE OR OTHERWISE, THAT EXTEND BEYOND THE STATEMENTS MADE ON THIS LABEL. No agent of Bayer CropScience is authorized to make any warranties beyond those contained herein or to modify the warranties contained herein. TO THE EXTENT CONSISTENT WITH APPLICABLE LAW, BAYER CROPSCIENCE DISCLAIMS ANY LIABILITY WHATSOEVER FOR SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OR HANDLING OF THIS PRODUCT. LIMITATIONS OF LIABILITY: TO THE EXTENT CONSISTENT WITH APPLICABLE LAW, THE EXCLUSIVE REMEDY OF THE USER OR BUYER FOR ANY AND ALL LOSSES, INJURIES OR DAMAGES RESULTING FROM THE USE OR HANDLING OF THIS PRODUCT, WHETHER IN CONTRACT, WARRANTY, TORT, NEGLIGENCE, STRICT LIABILITY OR OTHERWISE, SHALL NOT EXCEED THE PURCHASE PRICE PAID, OR AT BAYER CROPSCIENCE’S ELECTION, THE REPLACEMENT OF PRODUCT.

NET CONTENTS: 220 GALLONS

Axiom, Balance, Buctril, Liberty, Option, Epic, and Sencor are registered trademarks of Bayer. Banvel®, Basagran®, Clarity®, Distinct®, Galaxy®, Lightning®, Marksman®, Passport®, Poast®, Poast Plus®, Prowl®, Pursuit®, Raptor®, Resolve®, Scepter®, and Storm® are trademarks of BASF Corporation. FirstRate®, Hornet®, Python®, Scorpion III® and Sonalan HFP® are trademarks of Dow Agro Sciences. Accent®, Accent® Gold™, Assure II®, Basis®, Basis Gold®, Canopy®, Canopy XL®, Classic®, Concert®, Extrazine II®, Lorox®, Pinnacle®, Reliance STS® and Synchrony STS® are trademarks of DuPont. Aim®, Authority Broadleaf®, Command® and Gauntlet® are trademarks of FMC Corporation. Battalion®, Permit®, Roundup® and Roundup Ultra®, are trademarks of Monsanto. Beacon®, Callisto™, Eradicane®, Exceed®, Flexstar®, Fusilade®, Fusion®, Northstar®, Reflex®, Spirit® Tornado® and Touchdown® are trademarks of Syngenta. Cobra®, Resource® and Select® are trademarks of Valent.

Produced for

Bayer CropScience LP 800 N. Lindbergh Blvd. St. Louis, MO 63167 1-866-99BAYER (1-866-992-2937)

FLUFENACET 4 SC HERBICIDE (PENDING) 04/17/2019, 01/22/2020, 08/20/2020, 12/17/2020