crop-chem-docs/corpus/epa_ppls/34704-207.md

DIMETHOATE 400

• EPA Reg No: 34704-207
• Registrant: LOVELAND PRODUCTS, INC.
• Signal word: Warning
• Active ingredients: Dimethoate (43.5%)
• Label accepted: 2014-06-05
• Source PDF: https://www3.epa.gov/pesticides/chem_search/ppls/034704-00207-20140605.pdf

---

UNITED STATES ENVIRONMENTAL PROTECTION AGENCY WASHINGTON, DC 20460 OFFICE OF CHEMICAL SAFETY AND POLLUTION PREVENTION Premjit Halarnkar, Ph.D., MPA Registration Manager HIM H Loveland Products, Inc. Jun U P.O. Box 1286 Greeley, CO 80632-1286 Subject: Label Notification per PRN 98-10 - Revision of the ornamental crops statement Product Name: Dimethoate 400 EPA Registration Number: 34704-207 Application Date: 6/5/2014 Decision Number: 491834 Dear Dr. Halarnkar, The Agency is in receipt of your Application for Pesticide Notification under Pesticide Registration Notice (PRN) 98-10 for the above referenced product. The Registration Division (RD) has conducted a review of this request for its applicability under PRN 98-10 and finds that the action requested falls within the scope of PRN 98-10. The Agency acknowledges the following label change:

1. Revision of the ornamental crops statement The label submitted with the application has been stamped "Notification" and will be placed in our records. If you have any questions, you may contact me at (703) 347-0559 or via email at marchese.jacquelyn@epa.gov Sincerely, Jacquelyn Marchese, Entomologist Insecticide-Rodenticide Branch Registration Division (7505P) Office of Pesticide Programs

c 2 '/egjjfl read Instructions on reverse before completing form. Form Approved. OMB No. Z070-OQ6Q United States £ P/\ Environmental Protection Agency Washington. DC 20460 D Registration D Amendment S3 Other OPP Identifier Numbe Application for Pesticide -

1. Company/Product Number 34704-207
2. Company/Product (Name) DIMETHOATE 400
3. EPA Product Manager Venus Eagle PMtt
4. Proposed Classification S None D Restricted
5. Name and Address of Applicant (Include ZIP Code) Loveland Products Inc. P.O. Box 1286 Greeley, CO 80632-1286 f'i Check If this is a new address
6. Expedited Review. In accordance with FIFRA Section 3(c)(3)(b)(i), my product is similar or identical in composition and labeling to: EPA Reg. No. Product Name Section - II D Amendment- Explain below. CJ Resubmission in response to Agency letter dated 0 Notification - Explain below. [J Final printed labels in response to D "Me Too" Application. A*encv letter dated D Other - Explain below. Explanation : Use additional page(s) If necessary. (For Section I and Section II.) A minor revision on the label per EPA's email dated May 27, 2014. NOTIFICATION JUN 0 5 20tt Section - III
7. Material This Product Will Be Packaged In: Child Resistant Packaging D Yes* S No

• Certification must be submitted Unit Packaging DYes* 0 No If'Yes" Unit Packaging wgt. No. per container Water Soluble Packaging D Yes* S3 No If "Yes" Package wgt N/A No. per container N/A

2. Type of Container D Metal S3 Plastic D Glass D Paper D Other (Specify)
3. Location of Net Contents Information SJj Label jj Container
4. Size(s) RetailContainer 2.5 GAL, 30 GAL, 55 GAL, BULK
5. Location of Label Directions 0 On Label I—I On Label accomoanvinH product
6. Manner in Which Label is Affixed to Product D Lithograph D Paper glued D Stenciled Other Self-Adhesive Section - IV
7. Contact Point (Complete items directly below for Identification of Individual to be contacted, If necessary, to process this application.) Name Premjit Halarnkar, Ph.D., MPA premjit.halarnkar@cpsagu.com Title Manager of Registrations Telephone No. (Include Area Code) (970) 685-3579 Certification I certify that the statements I have made on this form and all attachments thereto are true, accurate and complete. I acknowledge that any knowingly false or misleading statements may be punishable by fine or imprisonment or both under applicable law.
8. Signature
9. Tyoed Name Premjit Halarnkar, Ph.D., MPA premjlt.halarnkaf@cpsagu.com
10. Title Manager of Registrations
11. Date 6/5/2014
12. Date Application Received (Stamped) EPA Form 8570-1 (Rev. 8-94) Previous editions are obsolete.

C C LovelandPRODUCTS Get Growing June 5, 2014 Venus Eagle (PM 1) Insecticide-Rodenticide Branch/Registration Division Document Processing Desk (NOTIF) Office of Pesticide Programs (7504C) U.S. Environmental Protection Agency Room S4900, One Potomac Yard 2777 S Crystal Drive Arlington, VA 22202 Subject: Dimethoate 400 (EPA Reg. No. 34704-207) Submission of Revised Label Dear Ms. Eagle: "Per EPA'sTemairdated May27 20147 to veland Products is submitting this notification for the revised label for Dimethoate 400 (EPA Reg. No. 34704-207). Enclosed, please find the following documents in support of this application.

1. Form 8570-1 Application
2. One copy of the red-lined label
3. One copy of the black-lined label This notification is consistent with the provisions of PR Notice 98-10 and EPA regulations at 40 CFR 152.46, and no other changes have been made to the labeling or the confidential statement of formula of this product. I understand that it is a violation of 18 U.S.C. Sec. 1001 to willfully make any false statement to EPA. I further understand that if this notification is not consistent with the terms of PR Notice 98-10 and 40 CFR 152.46, this product may be in violation of FIFRA and I may be subject to enforcement action and penalties under sections 12 and 14 of FIFRA. If you have any questions, please contact me at (970) 685-3579 or by email: premiit.halarnkar@cpsagu.com Sincerely, Premjit Halarnkar, Ph.D., MPA Registration Manager PO Box 1286, Greeley, CO 80632-1286 • Phone: (970) 685-3300 • Fax: (970) 685-3911

r Love/and NOTIFICATION JUN 0 5 20ft c GROUP [El INSECTICIDE | DIMETHOATE 4 I I Organophosphate Insecticide SYSTEMIC INSECTICIDE-MITICIDE ACTIVE INGREDIENT: Dimethoate (0,0-dimethyl-S-[(methylcarbamoyl) methyl] phosphorodithioate) OTHER INGREDIENTS:* TOTAL . 43.5% . 56.5% 100.0% This product contains petroleum distillates. (1.0 gallon contains 4.0 pounds of dimethoate) KEEP OUT OF REACH OF CHILDREN WARNING—AVISOSi usted no entiende la etiqueta, busque a alguien para que se la explique a usted en details. (If you do not understand this label, find _someoneJo.explainJt_tp_yo.ujn_detail.) , See Below For Additional Precautionary Statements DO NOT STORE BELOW 45 °F. FIRST AID If swallowed: If in eyes: If on skin or clothing: If inhaled: Call a poison control center or doctor immediately for treatment advice. Do not give any liquid to the person. Do not induce vomiting unless told to do so by the poison control center or doctor. Do not qive anything bv mouth to an unconscious person. Hold eye open and rinse slowly and gently with water for 15 to 20 minutes. Remove contact lenses, if present, after the first 5 minutes, then continue rinsing eye. Call a poison control center or doctor for treatment advice. Take off contaminated clothing. Rinse skin immediately with plenty of water for 1 5 to 20 minutes. Call a poison control center or doctor for treatment advice. Move person to fresh air. If person is not breathing, call 911 or an ambulance, then give artificial respiration, preferably by mouth-to-mouth, if possible. • Call a poison control center or doctor for further treatment advice. Have the product container or label with you when calling a poison control center or doctor, or going for treatment. NOTE TO PHYSICIANS: Contains petroleum distillate. Vomiting may cause aspiration pneumonia. Contains an Organophosphate that inhibits cholinesterase. Atropine is antidotal only if symptoms of cholinesterase inhibition are present. Pralidoxime chloride (2-PAM; PROTOPAM chloride) may be effective as an adjunct to atropine. Use according to label directions. FOR A MEDICAL EMERGENCY INVOLVING THIS PRODUCT CALL: 1-866-944-8565. EPA REG. NO. 34704-207 EPA EST. NO. 34704-MS-001 NET CONTENTS 2.5 GAL (9.46 L) 1 020614V2D06Y14

CDIMETHOATE 400 EPA REG. NO. 34704-207 PRECAUTIONARY STATEMENTS HAZARDS TO HUMANS AND DOMESTIC ANIMALS WARNING May be fatal if swallowed. Causes substantial but temporary eye injury. Do not get in eyes or on clothing. Harmful if absorbed through skin. Avoid contact with skin. Personal Protective Equipment (PPE): Some materials that are chemical-resistant to this product are barrier laminate, butyl rubber (> 14 mils), nitrile rubber (> 14 mils) and viton (> 14 mils). If you want more options, follow the instructions for category "F" on an EPA chemical-resistance category selection chart. Mixers, loaders, applicators, tlaggers, and other handlers must wear: • Long-sleeved shirt and long pants, • Shoes plus socks, • Chemical-resistant gloves, • Protective eyewear (goggles, face shield, or safety glasses), • A NIOSH-approved dust mist filtering respirator with MSHA/IMIOSH approval number prefix TC-21C or a NIOSH-approved respirator with any R, P, or HE filter, • Chemical-resistant apron when mixing, loading, cleaning up spills, or equipment. See Engineering Controls for additional requirements and exceptions. User Safety Requirements: Follow manufacturer's instructions for cleaning/maintaining PPE. If no such instructions for washables exist, use detergent and hot water. Keep and wash PPE separately from other laundry. Discard clothing and other absorbent materials that have been drenched or heavily contaminated with this product's concentrate. Do not reuse them. Engineering Controls: Mixers and loaders supporting aerial application to alfalfa, corn, cotton, safflower, sorghum, soybeans, and wheat must use a closed sys- tem that meets the requirements listed in the Worker Protection Standard (WPS) for agricultural pesticides [40 CFR 170.240(d)(4)]. The system must be capable of removing the pesticide from the shipping container and transferring it into mixing tanks and/or application equipment. At any disconnect point, the system must be equipped with a dry disconnect or dry couple shut-off device that is warranted by the manufacturer to minimize drippage to no more than 2.0 ml per disconnect. In addition, mixers and loaders must: • Wear the personal protective equipment required on this labeling for mixers/loaders, except no respirator is required; • Wear protective eyewear, if the system operates under pressure; and • Be provided and have immediately available for use in an emergency, such as a broken package, spill, or equipment breakdown, chemical resistant footwear and a respirator of the type specified in the PPE section of this labeling. Pilots must use an enclosed cockpit that meets the requirements listed in the Worker Protection Standard (WPS) for agricultural pesti- cides [40 CFR 170.240(d)(6)]. Pilots need not wear the PPE required in this labeling for applicators, but must wear at least a long-sleeved shirt, long pants, shoes, and socks. When handlers use closed systems, or enclosed cabs in a manner that meets the requirements listed in the Worker Protection Standard (WPS) for agricultural pesticides [40 CFR 170.240(d)(4-5)], the handler PPE requirements may be reduced or modified as specified in the WPS. USER SAFETY RECOMMENDATIONS Users should: • Wash hands before eating, drinking, chewing gum, using tobacco or using the toilet. • Remove clothing/PPE immediately if pesticide gets inside. Then wash thoroughly and put on clean clothing. • Remove PPE immediately after handling this product. Wash the outside of gloves before removing. As soon as possible, wash thoroughly and change into clean clothing. ENVIRONMENTAL HAZARDS This product is toxic to wildlife and aquatic invertebrates. This product is highly toxic to bees and other pollinators exposed to direct treat- ment or residues on blooming crops or weeds. Do not apply this product or allow it to drift to blooming crops or weeds if bees or other pollinating insects are foraging in the treatment area.

f (, 6 (7 DIMETHOATE 400 EPA REG. NO. 34704-207 Do not apply directly to water, or to areas where surface water is present or to intertidal areas below the mean high water mark. Do not contaminate water when disposing of equipment washwater or rinsate. Dimethoate is'known to leach through soil into ground water under certain conditions as a result of label use. Use of this chemical in areas where soils are permeable, particularly where the water table is shallow, may result in ground-water contamination. This product may contaminate water through drift of spray in wind. This product has a high potential for runoff for several days after application. Poorly draining soils and soils with shallow water tables are more prone to produce runoff that contains this product. A level, well maintained vegetative buffer strip between areas to which this product is applied and surface water features such as ponds, streams, and springs will reduce the potential for contamination of water from rainfall-runoff. Runoff of this product will be reduced by avoiding applications when rainfall is forecasted to occur within 48 hours. A vegetative filter strip constructed and maintained in accordance with the 2000 Natural Resources Conservation Service publication Conservation Buffers to Reduce Pesticide Losses (http://www.nrcs.usda.gov/feature/buffers/) will significantly reduce the potential for contamination of water from rainfall-runoff. PHYSICAL AND CHEMICAL HAZARDS Combustible. Do not use or store the product near heat or open flame. DIRECTIONS FOR USE It is a violation of Federal law to use this product in a manner inconsistent with its labeling. This product is for use in commercial settings only. Use in residential settings is prohibited. Do not apply this product in a way that will contact workers or other persons, either directly or through drift. Only protected handlers may be in the area during application. For any requirements specific to your State or Tribe, consult the agency responsible for pesticide regulation. High Pressure Handwand Equipment: When applications are made by high pressure handwand equipment, the maximum application rate for all crops and use-patterns is 0.0025 pound active ingredient per gallon. Requirements for Reducing Spray Drift: Do not apply under circumstances where possible drift to unprotected persons or to food, forage, or other plantings that might be dam- aged or crops thereof rendered unfit for sale, use, or consumption can occur.

1. Use the largest droplet size consistent with acceptable efficacy. Formation of very small droplets may be minimized by appropriate nozzle selection, by orienting nozzles away from the air stream as much as possible, and by avoiding excessive spray boom pressure. For groundboom and aerial applications, use medium or coarser spray nozzles according to ASAE 572 definition for standard nozzles or a volume mean diameter (VMD) of 300 microns or greater for spinning atomizer nozzles.
2. Make aerial or ground applications when the wind velocity favors on target product deposition. Apply only when the wind speed is less than or equal to 10 mph. For all non-aerial applications, wind speed must be measured adjacent to the application site on the upwind side, immediately prior to application.
3. Do not make aerial or ground applications into areas of temperature inversions. Inversions are characterized by stable air and increasing temperatures with increasing distance above the ground. Mist or fog may indicate the presence of an inversion in humid areas. Where permissible by local regulations, the applicator may detect the presence of an inversion by producing smoke and observing a smoke layer near the ground surface.
4. Low humidity and high temperatures increase the evaporation rate of spray droplets and therefore the likelihood of increased spray drift. Avoid spraying during conditions of low humidity and/or high temperatures.
5. All aerial and ground application equipment must be properly maintained and calibrated using appropriate carriers.
6. For groundboom applications, apply with nozzle height no more than 4 feet above the ground or crop canopy.
7. For airblast applications, turn off outward pointing nozzles at row ends and when spraying the outer two rows. To minimize spray loss over the top in orchard applications, spray must be directed into the canopy.
8. For aerial applications, release spray at the lowest height consistent with efficacy and flight safety. If the application includes an aquatic buffer zone, 'do not release spray at a height greater than 10 feet above the ground or crop canopy.

r DIMETHOATE 400 EPA REG. NO. 34704-207 9. For aerial applications, the spray boom should be mounted on the aircraft so as to minimize drift caused by wing tip vortices. The minimum practical boom length should be used and must not exceed 75% of the wingspan or 90% of rotor blade diameter. Use upwind swath displacement. AGRICULTURAL USE REQUIREMENTS Use this product only in accordance with its labeling and with the Worker Protection Standard, 40 CFR part 170. This Standard con- tains requirements for the protection of agricultural workers on farms, forests, nurseries, and greenhouses, and handlers of agricul- tural pesticides. It contains requirements for training, decontamination, notification, and emergency assistance. It also contains spe- cific instructions and exceptions pertaining to the statements on this label about personal protective equipment (PPE), and restricted- entry interval. The requirements in this box only apply to uses of this product that are covered by the Worker Protection Standard. Do not enter or allow worker entry into treated areas during the restricted entry interval (REI). PPE required for early entry to treated areas that is permitted under the Worker Protection Standard and that involves contact with any- thing that has been treated, such as plants, soil, or water, is: •Coveralls over long-sleeved shirt and long pants, •Chemical-resistant gloves made of any waterproof material, •Chemical-resistant footwear plus socks, •Chemical-resistant headgear for overhead exposure. Notify workers of the application by warning them orally and by posting warning signs at entrances to treated area. AERIAL APPLICATION: USE AUTOMATIC FLAGGING DEVICES WHENEVER FEASIBLE. APPLICATION THROUGH IRRIGATION SYSTEMS- CHEMIGATION Apply this product only through sprinkler, including center pivot, lateral move, end tow, side (wheel) roll, traveler, big gun, solid set, or JiajidjTipj/e;f|ood(basln);_furrow; border; or drip (trickle) irrigation systems. Do not apply this product through any other type of jrriga- tion system. Crop injury, lack of effectiveness, or illegal pesticide residues in the crop can result from nonuniform distribution of treated water. If you have questions about calibration, you should contact State Extension Service specialists, equipment manufacturers or other experts. Do not connect an irrigation system (including greenhouse systems) used for pesticide application to a public water system unless the pesticide label-prescribed safety devices for public water systems are in place. A person knowledgeable of the chemigation system and responsible for its operation, or under the supervision of the responsible person, shall shut the system down and make necessary adjustments should the need arise. Mix in clean supply tank the specified amount of this product for acreage to be covered, and needed quantity of water. This product should not be tank-mixed with other pesticides, surfactants or fertilizers unless prior use has shown the combination non- injurious under your conditions of use. Follow precautionary statements and directions for all tank-mixed products. On all crops, use sufficient gallonage of water to obtain thorough and uniform coverage, but not cause runoff or excessive leaching. This will vary depending on-equipment, pest problem and stage of crop growth. Application of more or less than optimal quantity of water may result in decreased chemical performance, crop injury or illegal pesticide residues. Meter this product into the irrigation water uniformly during the period of operation. Do not overlap application. Follow specified label rates, application timing, and other directions and precautions for crop being treated. Continuous mild agitation of pesticide mixture may be needed to assure a uniform application, particularly if the supply tank requires a number of hours to empty. CHEMIGATION SYSTEMS CONNECTED TO PUBLIC WATER SYSTEMS Note: Loveland Products, Inc. does not encourage connecting chemigation systems to public water supplies. The following information is provided for users who have diligently considered all other application and water supply options before electing to make such a connection.

r DIMETHOATE 400 EPA REG. NO. 34704-207 Public water system means a system for the provision to the public of piped water for human consumption if such system has at least 15 service connections or regularly serves an average of at least 25 individuals daily at least 60 days out of the year. Chemigation sys- tems connected to public water systems must contain a functional, reduced-pressure zone, backflow preventer (RPZ) or the functional equivalent in the water supply line upstream from the point of pesticide introduction. As an option to the RPZ, the water from the public water system should be discharged into a reservoir tank prior to pesticide introduction. There shall be a complete.physical break (air gap) between the outlet end of the fill pipe and the top or overflow rim of the reservoir tank of at least twice the inside diameter of the fill pipe. The pesticide injection pipeline must contain a functional, automatic, quick-closing check valve to prevent the flow of fluid back toward the injection pump. The pesticide injection pipeline must contain a functional, normally closed, solenoid-operated valve located on the intake side of the injec- tion pump and connected to the system interlock to prevent fluid from being withdrawn from the supply tank when the irrigation system is either automatically or manually shut down. The system must contain functional interlocking controls to automatically shut off the pesticide injection pump when the water pump motor stops, or in cases where there is no water pump, when the water pressure decreased to the point where pesticide distribution is adversely affected. Systems must use a metering pump, such as a positive displacement injection pump (e.g., diaphragm pump) effectively designed and con- structed of materials that are compatible with pesticides and capable of being fitted with a system interlock.. Do not apply when wind speed favors drift beyond the area intended for treatment. SPRINKLER CHEMIGATION (FOLIAR SPRAY USES) The system must contain a functional check valve vacuum relief valve, and low pressure drain appropriately located on the irrigation pipeline to prevent water source contamination from backflow. The pesticide injection pipeline must contain a functional, automatic, quick-closing check valve to prevent the flow of fluid back toward the injection pump. The pesticide injection pipeline must also contain a functional, normally closed, solenoid-operated valve located on the intake side of the injection pump and connected to the system interlock to prevent fluid from being withdrawn from the supply tank when the irrigation system is either automatically or manually shut down. The system must contain functional interlocking controls to automatically shut off the pesticide injection pump when the water pump motor stops. The irrigation line or water pump must include a functional pressure switch which will stop the water pump motor when the water pres- sure decreases to the point where pesticide distribution is adversely affected. Systems must use a metering pump, such as a positive displacement injection pump (e.g., diaphragm pump) effectively designed and con- structed of materials that are compatible with pesticides and capable of being fitted with a system interlock. Do not apply when wind speed favors drift beyond the area intended for treatment. FLOOD (BASIN), FURROW AND BORDER CHEMIGATION (SOIL DRENCH USES) Systems using a gravity flow pesticide dispensing system must meter the pesticide into the water at the head of the field and downstream of a hydraulic discontinuity .such as a drop structure or weir box to decrease potential for water source contamination from backflow if water flow stops. Systems utilizing a pressurized water and pesticide injection system must meet the following requirements: a. The system must contain a functional check valve, vacuum relief valve, and low pressure drain appropriately located on the irrigation pipeline to prevent water source contamination from backflow. b. The pesticide injection pipeline must contain a functional, automatic, quick-closing check valve to prevent the flow of fluid back toward the injection pump. c. The pesticide injection pipeline must also contain a functional, normally closed, solenoid-operated valve located on the intake side of the injection pump and connected to the system interlock to prevent fluid from being withdrawn from the supply tank when the irrigation system is either automatically or manually shut down. d. The system must contain functional interlocking controls to automatically shut off the pesticide injection pump when the water pump motor stops. e. The irrigation line or water pump must include a functional pressure switch which will stop the water pump motor when the water pressure decreases to the point where pesticide distribution is adversely affected. f. Systems must use a metering pump, such as a positive displacement injection pump (e.g., diaphragm pump) effectively designed and constructed of materials that are compatible with pesticides and capable of being fitted with a system interlock. 5

C DIMETHOATE 400 EPA REG. NO. 34704-207 DRIP (TRICKLE) CHEMIGATION (SOIL DRENCH USES) The system must contain a functional check valve, vacuum relief valve and low pressure drain appropriately located on the irrigation pipeline to prevent water source contamination from backflow. The pesticide injection pipeline must contain a functional, automatic, quick-closing check valve to prevent the flow of fluid back toward the injection pump. The pesticide injection pipeline must also contain a functional, normally closed, solenoid-operated valve located on the intake side of the injection pump and connected to the system interlock to prevent fluid from being withdrawn from the supply tank when the irrigation sys- tem is either automatically or manually shut down. The system must contain functional interlocking controls to automatically shut off the pesticide injection pump when the water pump motor stops. The irrigation line or water pump must include a functional pressure switch which will stop the water pump motor when the water pres- sure decreases to the point where pesticide distribution is adversely affected. Systems must use a metering pump such as a positive displacement injection pump (e.g., diaphragm pump) effectively designed and con- .structed of materials that are compatible with pesticides and capable of being fitted with a system interlock. USE DIRECTIONS BEFORE USING, READ WARNING STATEMENTS ON CONTAINER LABEL This product is for use in conventional hydraulic sprayers, ground applicators, aerial sprayers and listed chemigation equipment. Do not apply when weather conditions favor drift of spray from treated areas. Repeat applications as necessary unless otherwise specified. Consult your state experiment station or state extension service for proper timing of applications. -Dimethoate-400-has-systemic-and-contact-activity-against-a broad spectrum of-piercing, sucking and-chewing insects. - - - - •- COMPATIBILITY: Dimethoate 400 is compatible in spray tank mixes with most insecticides, miticides, and fungicides, provided they are not alkaline in reaction. FOR PROPER MIXING, SPRAY TANK MUST BE AT LEAST THREE-QUARTERS FILLED WITH WATER BEFORE ADDING DIMETHOATE 400. MECHANICAL AGITATION OR RECIRCULATION THROUGH PUMP BYPASS TO TANK IS USUALLY SUFFICIENT FOR MAINTAINING A GOOD DISPERSION. To increase the consistency and performance of Dimethoate 400 when less than ideal water conditions exist (when pH is greater than 7), use LI 700® at 1.0 pint per 100 gallons of spray mixture. Spray tank mixtures of Dimethoate 400 with alkaline insecticides and fungicides should be applied promptly. ODOR: Dimethoate 400 formulations may produce a distinctive odor during the spray operation, but under normal conditions this odor does not persist. Aerial Applications: Apply at least 1.0 gallon of finished spray per acre. Apply at least 5.0 gallons of finished spray per acre in California. Automatic flagging devices should be used whenever feasible. If human flaggers are employed, they must wear the protective clothing and respirator specified on this label. Ground Applications: Use water for dilution and apply at least 5.0 gallons of finished spray per acre unless otherwise directed.

c c .(01 DIMETHOATE 400 EPA REG. NO. 34704-207 FRUIT TREES (INCLUDING NONBEARING AND NURSERY STOCK) Crops Pears Cherries Preharvest Idaho, Oregon and Washington only
Cherries Postharvest (trees~afterharvest) ~ Idaho, Oregon, and Washington only Pests Controlled Aphids Leafhoppers Mites (except Rust mite) Pear osvlla Rate 0.5 to 1. Opt/1 00 gal water (0.25 to 0.5 Ib Al/IOOgal) Interval (Days) Between Last Application and Harvest 28 Do not apply when trees or substantial numbers of weeds in the orchard are in bloom. Maximum application rate: 1.0 pound active ingredient per acre. Maximum total application rate per year: 1.0 pound active ingredient per acre. The REI is 10 days; however, the REI is increased to 14 days in outdoor areas where the average annual rainfal is less than 25 inches per year. Aphids Cherry fruit fly Mites Dilute Applications: 0.5 pt/A (0.25 Ib AI/A) in a minimum of 100 gal water; Concentrate Applications: Use up to 2.66 pt/A (1.33 Ib AI/A) in a minimum of 50.0 aal water 21 Concentrate sprays should be used with caution to avoid fruit marking and injury. Make a single application within 7 days of adult fly emergence in the area. This single application should be made in late May or early June when the fruit are small in size. Maximum application rate: 1.33 pounds active ingredient per acre. Maximum total application rate per year: 1.33 pounds active ingredient per acre. The REI is 10 days; however, the REI is increased to 14 days in outdoor areas where the averaae annual rainfall is less than 25 inches oer vear. Aphids Cherry fruit fly Mites Dilute Applications:

1. Opt/1 00 gal water Dotiot-exceed 2:66-pt/A - or1.33lbAI/A Make a single application a minimum of 7 days after final harvest or apply in cases where a decision is made not-to harvest due to poor fruit quality; a- light crop, or unfavorable market conditions. For best results, make application before fruit hardens or drops. Maximum application rate: 1.33 pounds active ingredient per acre. Maximum total application rate per year: 1.33 pounds active ingredient per acre. The REI is 10 days; however, the REI is increased to 14 days in outdoor areas where the averaae annual rainfall is less than 25 inches oer vear. CITRUS TREES INCLUDING NONBEARING AND NURSERY STOCK Consult your state agricultural experimental station or state agricultural extension service for proper timing application. Restrictions: Maximum application rate: 1.0 pound active ingredient per acre per year. The REI is 10 days; however, the REI is increased to 14 days in outdoor areas where the average annual rainfall is less than 25 inches per year. Crops Grapefruit Lemons. Oranges Tangerines Pests Controlled Aphids . Mites (except Rust mite) Scales (except Black or Snow) Rate Ground Equipment: 0.5 to 1. Opt/1 00 gal water. Apply as an outside coverage sorav. Ground Equipment: 0.5 to 1 .Opt/1 00 gal water. Apply as a thorough distribution coverage spray. Ground Equipment: 1.0 to 1.5 pt/100gal water. Apply as a thorough coverage sorav. Interval (Days) Between Last Application and Harvest 15 15 15 Cont'd. next page

(//IT DIMETHOATE 400 EPA REG. NO. 34704-207 Citus Trees Includina Non Crops Grapefruit Lemons Oranges Tangerines CITRUS: (California, Arizona: Nonbearing and nursery stock) Grapefruit Lemons Oranges Tanaerines CITRUS: Grapefruit Lemons Oranges Tangerines (Arizona only) bearina and Nurserv Stock cont'd.: Pests Controlled Thrips Whiteflies Citrus psyllid Rate Ground Equipment: 0.5 to 1. Opt/1 00 gal water. Aoplv as a mist sprav. Ground Equipment: 1 .0 pt/1 00 gal water. Apply as a thorough distribution coverage spray. Aerial application: 1.0 pt in a minimum of 5.0 gal water. Interval (Days) Between Last Application and Harvest 15 15 Thorough coverage is necessary. Do not apply when trees or substantial number of weeds in the grove are in bloom. Do not use on citrus seedlinas. Make no more than 2 aoolications to mature fruit. Aphids Thrips Foliar Spray: 1.0 pt/1 00 gal water Soil Drench (trees 1 to 3 vrold): 1.0 at/A 15 Repeat applications as necessary. May be applied in the year grapefruit, lemon, orange and tangerine trees begin to bear fruit. Apply in the furrow or basin around the base of tree. Aoolv when insect injury to new growth appears. Do not apply to trees that will bear fruit within 1 year. The REI is 10 days; however, the REI is increased to 14 days in outdoor areas where the averaae annual rainfall is less than 25 inches per vear. Thrips Aerial application: 2.0 pt/5.0 gal water Ground application: 2.0 pt/20.0 aal water 15 The REI is 10 days; however, the REI is increased to 14 days in outdoor areas where the average annual rainfall is less than 25 inches per vear. Note: Use of dimethoate is prohibited during any time of day in any given orchard from when that orchard has 10% open blooms until such time as there has been at least 75% petal fall on the north side of the trees. Applications of dimethoate shall be limited to that peri- od of time between one (1) hour after sunset to three (3) hours before sunrise when any one of the following conditions prevail: 1) Before the onset of petal fall, the orchard to be treated has open blooms present and these open blooms represent less than 10% of the total anticipated blooms in the orchard. 2) After the initiation of petal fall there are less than 25% of open blooms remaining in the orchard to be treated. 3) It is between the calendar dates of February 15th and May 1st. All applications of dimethoate on citrus must be documented on Form 1080 written either by a pest control advisor, farm owner or farm manager as is normally required for custom applications of pesticides; except that private applicators may omit the "Pesticide Application Report" section. The description of the status of bloom of the orchard to be treated as it was at the time of the application shall be indi- cated in the section for "Label Restrictions/Special Instruction." Both private and custom applicators shall mail to the Agriculture Department's Phoenix office the original or each completed Form 1080 done in accordance with this label. Each Form 1080 shall be post- marked not later than Monday following the week in which the application was made, except when holidays intervene. PECANS FOR COMMERCIAL USE ONLY Crops Pecans Pests Controlled Aphids Leafhoppers Mites Rate 0.66 pt/A (0.33 Ib AI/A) Interval (Days) Between Last Application and Harvest 21 Maximum application rate: 0.33 pound active ingredient per acre and no more than 1 REI is 48 hours. application per year. The

DIMETHOATE 400 EPA REG. NO. 34704-207 VEGETABLE CROPS FOR COMMERCIAL USE ONLY Crops Asparagus (Do not use on Asparagus in California or Arizona) Beans (including fresh, Snap, Lima and dry; excluding Cow peas) Broccoli Cauliflower r» _L 13russels~sprouts - Celery (Florida) Garbanzo beans Endive Escarole Kale Pests Controlled Aphids Asparaaus beetles Rate

1. Opt/A (0.5lbAI/A) Interval (Days) Between Last Application and Harvest 180 Apply after the last harvest. Do not apply less than 180 days before harvest. Maximum single application rate: 0.5 pound active ingredient per acre, 1 4-day retreatment interval. Maximum total rate per season: 1 .0 pound active inaredient per acre. The REI is 48 hours. Aphids Bean leaf beetle Grasshoppers Leafhoppers Leaf miners Lygus bugs Mexican bean beetle Mites 0.5 to 1. Opt/A (0.25 to 0.5 Ib AI/A) Beans may be harvested mechanically on day of application. This pesticide is highly toxic to bees; do not apply if bees are visiting the areas to be treated when crop or weeds are in bloom. Maximum single application rate: 0.5 pound active ingredient per acre, 14-day retreatment interval. Maximum total rate oer season: 1 .0 pound active inaredient oer acre. The REI is 48 hours. Aphids 0.5 to 1 .0 pt/A (0.25 to 0.5 Ib AI/A) 7 Maximum application rate: 0.5 pound active ingredient per acre, 7-day retreatment interval. Maximum total rate per season: 1 .5 pounds active ingredient per acre. The REI is 48 hours; however, the REI is increased to 72 hours in outdoor areas where the averaae annual rainfall is ess than 25 inches oer vear. Aphids • Apply when insects first appear and repeat as needed. -Ground-Equipment: Apply up to 1.0 pt/A (0.5 Ib AI/A) in a minimum of 100 gal of water/A. Do not apply by air. 10 - - - Maximum application rate: 0.5 pound active ingredient per acre, 7-day retreatment interval. Maximum total rate per year: 1 .5 pounds active ingredient per acre. The REI is 48 hours; however, the REI is increased to 72 hours in outdoor areas where the average annual rainfall is less than 25 inches per year. Carmine mite Leaf miners Two-spotted spider mite 1.0 pt/A (0.5 Ib AI/A) 7 Maximum application rate: 0.5 pound active ingredient per acre, 7-day retreatment interval. Maximum total rate per year: 1 .5 pounds active ingredient per acre. The REI is 48 hours. Aphids Grasshoppers Leafhoppers Leaf miners Lygus bugs Mites 0.5 to 1 .0 pt/A (0.25 to 0.5 Ib AI/A) Beans may be harvested mechanically on day of application. This pesticide is highly toxic to bees; do not apply if bees are visiting the areas to be treated when crop or weeds are in bloom. Maximum application rate: 0.5 pound active ingredient per acre, 14-day retreatment interval. Maximum total rate oer season: 1.0 oound active inaredient per acre. The REI is 48 hours. Aphids Leafhoppers Leaf miners 0.5 pt/A (0.25 Ib AI/A) 14 Leaf lettuce Mustard greens Swiss chard Turnip (greens and roots) Endive, Escarole, Leaf lettuce and Swiss chard: Maximum application rate: 0.25 pound active ingredient per acre, 7-day reapplication interval. Maximum total rate per year: 0.5 pound active ingredient per acre. The REI is 48 hours. Kale: Maximum application rate: 0.25 pound active ingredient per acre, 15-day reapplication interval. Maximum total rate per year: 0.5 pound active ingredient per acre. The REI is 48 hours. Mustard greens: Maximum application rate: 0.25 pound active ingredient per acre, 9-day reapplication interval. Maximum total rate per year: 0.5 pound active ingredient per acre. The REI is 48 hours. Turnips: Maximum application rate 0.25 pound active ingredient per acre, 3-day reapplication interval. Maximum total rate per vear: 1.75 pounds active ingredient per acre. The REI is 48 hours.

f cDIMETHOATE 400 EPA REG. NO. 34704-207 Crops Lentils Lupine ' Pests Controlled LVQUS bua Rate 1.0ot/A (0.5 Ib AI/A) Interval (Days) Between Last Application and Harvest 14 Maximum application rate: 0.5 pound active ingredient per acre, 7-day reapplication interval. Maximum total rate per vear: 1 .0 pound active inaredient oer acre. The REI is 48 hours. Aphids 0.5 to 1 .0 pt/A (0.25 to 0.5 Ib AI/A) 14 This pesticide is highly toxic to bees; do not apply if bees are visiting the areas to be treated when crop or weeds are in bloom. Maximum application rate: 0.5 pound active ingredient per acre, 7-day reapplication interval. Maximum total rate per vear: 1 .0 pound active inaredient per acre. The REI is 48 hours. Aphids LVQUS buas 0.5 to 1 .0 pt/A (0.25 to 0.5 Ib AI/A) Apply when Aphids first appear. Lupine may be harvested mechanically on dav of application. Do not feed treated vines. This pesticide is highly toxic to bees, do not apply if bees are visiting the areas to be treated when crop or weeds are in bloom. Maximum application rate: 0.5 pound active ingredient per acre, 14-day retreatment interval. Maximum total rate per year: 1.0 pound active ingredient per acre. The REI is 4.8 hours. Melons (except watermelons) Watermelons Peas (succulent) Peppers Potatoes Tomatoes Aphids Leafhoppers Leaf miners Thrips 1.0 pt/A (0.5 Ib AI/A) 3 Maximum application rate: 0.5 pound active ingredient per acre, 7-day reapplication interval. Maximum total application rate per vear: 1 .0 pound active inaredient per acre. The REI is 48 hours. Aphids Leafhoppers Leaf miners 0.5 to 1.0 pt/A (0.25 to 0.5 Ib AI/A) 3 Maximum application rate: 0.5 pound active ingredient per acre, 7-day reapplication interval. Maximum total application rate per vear: "1.0 pound active inaredient per acre. The REI is 48 holirs. Aphids 0.32 pt/A (0.1 6 Ib AI/A) Peas may be harvested mechanically on day of application. This pesticide is highly toxic to bees; do not apply if bees are visitng the areas to be treated when crop or weeds are in bloom. Maximum application rate 0.16 pound active ingredient per acre. Maximum total rate oer vear: 0.16 oound active inaredient per acre. The REI is 48 hours. Not for use on field peas. Aphids Leaf miners Maaaots 0.5 to 0.6 pt/A (0:25 to 0.33 Ib AI/A) Peppers may be harvested mechanically on day of application. Maximum application rate 0.33 pound active ingredient per acre, 7-day reapplication interval. Maximum total rate per vear: 1 .65 oound active inaredient per acre. The REI is 48 hours. Aphids Grasshoppers Leafhoppers Leaf miners 0.5 to 1 .0 pt/A (0.25 to 0.5 Ib AI/A) Potatoes may be harvested mechanically on day of application. Maximum application rate: 0.5 pound active ingredient per acre, 7-day reapplication interval. Maximum total rate per vear: 1 .0 pound active inaredient per acre. The REI is 48 hours. Aphids Leafhoppers Leaf miners 0.5 to 1.0 pt/A (0.25 to 0.5 Ib AI/A) 7 Maximum application rate 0.5 pound active ingredient per acre, 6-day reapplication interval. Maximum total rate per vear: 1.0 pound active inaredient per acre. The REI is 48 hours. Where Cabbage worms and Cabbage loopers are a problem, the above rates of Dimethoate 400 are compatible with endosulfan or malathion. Use in accordance with the manufacturers directions for control of these insects. 10

DIMETHOATE 400 EPA REG. NO. 34704-207 FIELD AND SEED CROPS Crops FIELD CROPS: Alfalfa (Hay) Pests Controlled Aphids Grasshoppers Leafhoppers Plant bugs including Lygus reduction of Alfalfa weevil larvae Rate 0.5 to 1. Opt/A (0.25 to 0.5 Ib AI/A) Interval (Days) Between Last Application and Harvest 10 This pesticide is highly toxic to bees; do not apply if bees are visiting the areas to be treated when crop or weeds are in bloom. Do not apply within 10 days of harvest or pasturing. Maximum application rate: 0.5 pound active ingredient per acre. Maximum total rate per crop cycle or cutting: 0.5 pound active ingredient per acre. The REI is 48 hours. Field Corn Popcorn (corn grown for seed) Cotton (grown in California and Arizona) Cotton Safflower Sorghum (milo) Aphids Banksgrass mites (excluding Trans-Pecos area of Texas) Bean beetle Corn rootworm adult Two-spotted spider mite Grasshoppers 0.6 to 1. Opt/A (0.33 to 0.5 Ib AI/A)

1. Opt/A (0.5 Ib AI/A) 14 - forage •28 - grain Apply as necessary. Crops may be more susceptible to injury in the early reproductive stages. Do not apply to corn during the pollen-shed period if bees are present. Maximum application rate: 0.5 pound active ingredient per acre. Maximum total rate per year 0.5 pound active ingredient per acre. The is 48 hours PROHIBITION: Workers are prohibited from entering the treated area to perform detasseling tasks for 4 days in nonarid areas and for 15 days in outdoor areas where the average annual rainfall is less than 25 inches per vear. Fleahoppers Leafhoppers Plant bugs includina Lvaus 0.5 to 1. Opt/A (0.25 to 0.5 Ib AI/A) REI 14 Maximum application rate: 0.5 pound active ingredient per acre, 14-day retreatment interval. Maximum rate per season: 1 .0 pound active inaredient oer acre. The REI is 48 hours. Aphids Mites Thrips Fleahoppers Plant bugs includina Lvaus 0.25 to 0.5 pt/A (0.1 25 to 0.25 Ib AI/A) 0.5 pt/A (0.25 Ib AI/A) total 14 Maximum application rate: 0.5 pound active ingredient per acre, 14-day retreatment interval. Maximum rate per season: 1 .0 pound active inaredient per acre. The REI is 48 hours. Aphids Leafhoppers Plant bugs including Lygus Thrios 0.5 to 1.0 pt/A (0.25 to 0.5 Ib AI/A) total 14 Maximum application rate: 0.5 pound active ingredient per acre. Maximum total rate per crop cycle or cutting: 0.5 pound active inaredient per acre. The REI is 48 hours. Aphids Banksgrass mites (excluding Trans-Pecos area of Texas) Spider mites Grasshoppers Sorghum midge 0.5 to 1.0 pt/A (0.25 to 0.5 Ib AI/A) 1.0 pt/A (0.5 Ib AI/A) 1 .0 pt/A (0.5 Ib AI/A) 0.25 to 0.5 pt/A (0.1 25 to 0.25 Ib AI/A) 28 Maximum application rate: 0.5 pound active ingredient per acre, 7-day reapplication interval. Maximum total rate per season: 1.0 pound active inaredient per acre. The REI is 48 hours. 11

c DIMETHOATE 400 EPA REG. NO. 34704-207 Crops Soybeans Wheat Pests Controlled Aphids Bean leaf beetle Leafhoppers Mexican bean beetle Spider mites Three-cornered alfalfa hopper Grasshoppers Rate 1 .0 pt/A (0.5 Ib AI/A) 1 .0 pt/A (0.5 Ib AI/A) Interval (Days) Between Last Application and Harvest 21 Maximum application rate: 0.5 pound active ingredient per acre, 7-day reapplication interval. Maximum application rate per vear: 1.0 pound active inaredient per acre. The REI is 48 hours. Aphids (greenbugs) Brown wheat mite Grasshoppers 0.5 to 0.75 pt/A (0.25 to 0.375 Ib AI/A) 0.3 to 0.5 pt/A (0.1 6 to 0.25 Ib AI/A) 0.75 Dt/A (0.375 Ib AI/A) 35 Maximum single application rate: 0.5 pound active ingredient per acre. Maximum total application rate crop cycle: 0.5 pound active inaredient per acre. The REI is 48 hours. total per Crops SEED CROPS: Alfalfa Grasses (grown for seed) (Idaho, Oregon & Washington only) Pests Controlled Aphids Leafhoppers Lygus bugs Grasshoppers reduction of Alfalfa weevil larvae Rate 0.5 to 1.0 pt/A (0.25 to 0.5 Ib AI/A) Interval (Days) Between Last Application and Harvest 10 This pesticide is highly toxic to bees; do not apply if bees are visiting the areas to be treated weeds are in bloom. Maximum single application rate: 0.5 pound active ingredient per acre, application rate per croo cvcle: 0.5 pound active inaredient oer acre. The REI is 48 hours. Aphids Plant bugs Thrips Winter arain mites Apply 0.5 to 0.6 pt/A (0.25 to 0.33 Ib AI/A) in a minimum of 2.0 aal water Apply by ground or aerial application. Maximum application rate: 0.5 pound active ingredient per acre, 90-day retreatment interval rate per vear: 1 .0 oound active inaredient per acre. The REI is 48 hours. __.... when crop or Maximum total Maximum total Do not use on seed onions, seed carrots or seed bermuda grass. ORNAMENTAL PLANTS AND CHRISTMAS TREES GROWN IN NURSERIES ONLY Do not use on ornamental plants grown in greenhouses, Christmas tree and conifer plantations, landscapes, interiorscapes and residen- tial, public, recreational, commercial, industrial and institutional establishments. Dimethoate 400 is effective in controlling many sucking, piercing and chewing insects, including aphids, leaf miners, leafhoppers, mites, psyllids, scales and thrips that attack valuable ornamental plantings. For proper timing of treatments for the control of specific pests on ornamental plants, consult local agricultural authorities. Apply sprays uniformly and thoroughly to foliage, except as otherwise directed, when insects or their damage is first observed. Repeat applications as needed. Do not overdose or overspray. SOIL INJECTION: For control of pests on any Ornamental species, a soil injection application can be used. (DO NOT APPLY THIS PROD- UCT BY SOIL INJECTION IN CALIFORNIA). Use a 1:2 dilution (1 part Dimethoate 400 to 2 parts water) for all soil injections. Inject 0.5 fluid ounce of dilution per inch of tree cir- cumference (measure tree circumference at approximately 4 to 5 feet above ground level). Make injections within dripline of tree and into root zone at a depth appropriate for root uptake of the species type and species growth stage to be treated. Application can be made once per growing season or twice for difficult to control species such as ELM LEAF BEETLE. For control of Elm leaf beetle, apply once shortly after trees leaf out, then follow with a second application 6 to 8 weeks later if necessary. 12

r DIMETHOATE 400 EPA REG. NO. 34704-207 IMPORTANT: Use injection equipment capable of delivering metered dosage to a soil depth of at least 6 inches. Number of injections should equal inches of tree circumference. Avoid direct injections into live root tissue. Water heavily after injection, at least 2 inches of water is recommended. Some species such as Honeysuckle, River birch, Ornamental cherry, and Plum (Prunus spp.), Hawthorne, Japanese lace maple, and Aspens are more sensitive to Dimethoate 400 at early growth stages. Do not apply to sensitive species that have not been established for at least 3 years. DO NOT USE ON BEARING FRUIT TREES. Always wear full PPE (Personal Protective Equipment) as described on page 2 of this label for application, mixing, loading and handling of Dimethoate 400. Chemical resistant headgear not necessary for soil injection. DO NOT inject into soil areas where children or pets may dig or exhume treated soil. Do not make soil injections within 20 feet of edible crop gardens. Do not use on ornamental plants that are not listed on this label unless a sample test area has shown Dimethoate 400 is not phytotoxic- to your plants. A small test area should always be sprayed first before use. Do not use on any ornamental stock plants grown as a source of propagation material, such as cuttings, layers, root stocks or scions for grafting or budding. Do not use in spray mixtures containing oil. Do not use on plants growing in greenhouses. Restrictions: Herbaceous Ornamentals: Maximum application rate: 0.25 pound active ingredient per acre. Maximum total rate per year: 0.25 pound active ingredient per acre. The REI is 48 hours. Woody Ornamentals and Christmas Trees Nurseries: Maximum application rate 1.0 pound active ingredient per acre, 14-day reapplica- tion interval. Maximum total rate per year: 3.0 pounds active ingredient per acre. When applications are made by high pressure hand wand equipment, the maximum application rate for all crops and use patterns is 0.0025 pound active ingredient per gallon.The REI is 10 days; however, the REI is increased to 14 days in outdoor areas where the average annual rainfall is less than 25 inches per year. Crops Arborvitae Azaleas Birch Boxwood Camellias Carnations Cedar Cypress Daylillies Douglas fir Euonymus Pests Controlled Aphids Bagworm Mites Lace bug Leaf miners Mites Tea scale Whiteflies Aphids Leaf miners Leaf miners Mealybug Mites Aphids Camellia scale Mites Tea scale Aphids Mites Thrips Mites Bactra moth larvae Aphids Thrips Fir cone midge Aphids Scale Rate 3.5 fl oz in 1'0.0 gal water 1.75flozin 10.0 gal water 1.75flozin 10.0 gal water 1.75flozin 10.0 gal water Foliar spray: 1.75 fl oz in 10.0 gal water. Soil drench: 2.0 fl oz in 1.0 gal water. For plants up to 6' tall. Increase rate proportionately for larger plants. Soil drench: 2.0 floz /500 sq ft of bed or bench 3.5 floz in 10.0 gal water 1.75 floz in 10.0 gal water 3.5fl oz in 10.0 gal water 6.5 floz in 10.0 gal water 3. 5 floz in 10.0 gal water Interval (Days) Between Last Application and Harvest ..... For Leaf miners, apply when leaves are expanded, about mid-May, and repeat in early July. For Leaf miners, apply in spring when Leaf miner flies first appear, or in early summer for control of larvae in the infested leaves. Foliar spray: apply 2 sprays, 6 weeks apart the first year, followed by annual applications soon after first growth begins in the spring. Soil drench: apply as a soil drench around the base of plants in early spring. Apply in sufficient water for even distribution. Water in thoroughly following application. Apply as a drenching spray. Make thorough coverage application when cones are closed and pendant. Use hydraulic or backpack spraver. 13

r 19-11DIMETHOATE 400 EPA REG. NO. 34704-207 Crops Ficus nitida Gardenias Gerberas Gladiolus Hackberry Hemlock Holly (English & American) not Burford variety Honeysuckle Iris Juniper and other evergreen species Oak Pines Pinyon pine Poinsettia Prunus spp. Roses Taxus (upright or spreading yew) Pests Controlled Thrips Tea scale Whiteflv Thrips Aphids Thrips Hackberry budgall psyllid Hackberry nipplegall psvllid Mites Scale Leaf miners Mites Soft scale Honeysuckle aphid Aphids Iris borer Thrips Aphids Bagworms Midges Mites Golden oak scale Loblolly pine sawfly Nantucket pine tip moth Zimmerman pine moth Pinyon needle scale Pinyon "pitch mass" borer Pinyon spindle gall midge Tip moth Aphids Mealybug Mites Whiteflv Aphids Leafhoppers Mites Thrips Aphids Leafhoppers Mites Thrips Fletcher scale Mealybug Mites Rate 1.75 fl oz in 10.0 gal water 1.75 fl 02 in TO.O gal water 1.75flo2in 10.0 gal water

1. 75 fl 02 in 10.0 gal water 6.0 fl ozin 10.0 gal water
2. 75 f I oz in 10.0 gal water
3. 75 fl 02 in 10.0 gal water 3.5 fl ozin 10.0 gal water 3.5 fl ozin 10.0 gal water 3.5 fl ozin 10.0 gal water 3.5 fl ozin 10.0 gal water G.Oflozin 10.0 gal water 3.5 f I ozin 10.0 gal water 25.5 fl ozin 10.0 gal water
4. 75 f I ozin 10.0 gal water G.Oflozin 10.0 gal water 6.0 fl ozin 10.0 gal water 3.5 fl ozin 10.0 gal water Interval (Days) Between Last Application and Harvest Apply prior to bud break. Do not apply to plants that have not been established for at least 3 years. For Leaf miners, apply in spring when Leaf miner flies first appear, or in early summer, for control of larvae in infested leaves. Do not apply to plants that have not been established for at least 3 years. For Borer control, spray when new leaves are 5 to 6 inches tall. Apply when most larvae are in the second and third instars. Spray in mid-April and/or in early September for larvae control. Apply spray to egg masses at the base of the trees and to all rough bark and crotches that can be reached from the ground. Make this bark application when crawlers start to emerge from the eggs. Use hydraulic or backpack sprayer. Do not spray leaves or needles since phytotoxicity may result. For Spindle gall midge and Tip moth, apply in mid to late spring. For Pinyon borer, make application in earlv summer. 14

r DIMETHOATE 400 EPA REG. NO. 34704-207 Crops Pests Controlled Rate Christmas trees Bagworms Balsam twig aphid Blue aphid European pine shoot moth Mites Nantucket pine tip moth .Zimmerman pine moths Use 1.0 to 1.5 pt/A in 30.0 to 50.0 gal of water with a mist blower. Use 1.0 tblsp in a backpack or hand held sprayer. Ornamental shade and nursery trees Aphids Elm leaf beetle Soil Injection: Use 2.5 to 3.5 ml of product/inch of tree circumference measured at approximately 4.5 to 5 ft above ground level. For Aphid control, make 1 application. A second application 6 to 8 weeks later may be required during seasons of extreme pest pressure. Make 2 applications per season for Elm leaf beetle; once shortly after trees leaf out, and once 6 to 8 weeks later. Some species such as River birch, (Prunus spp.), Ornamental cherry, Hawthorne, Japanese lace maple and Aspens may show phytotoxic effects at label rates. DO NOT USE ON BEARING ORNAMENTAL TREES. Use a Kioritz Injector with a 6-inch probe tip or similar type equipment capable of delivering metered dosage. Follow Personal Protective Equipment section of this label. Insert product 4 to 6 inches below ground surface. Equally distribute injections radially in the area around the tree trunk to drip line. Number of insertions should equal inches of tree circumference. Do not inject concentrate directly into live root tissue. Water heavily after injection. At least 2 inches of water is recommended. CAUTION - DO NOT USE ON JAPANESE MAPLES OR RED LEAF ORNAMENTAL SPP. STORAGE AND DISPOSAL PROHIBITIONS: Do not contaminate water, food, or feed by storage or disposal. Open dumping is prohibited. Do not reuse empty con- •tainer-Do-not-store-under-eonditions whieh-might adversely affect-the container or its ability-to function properly. Do not ship or store with food, feeds, drugs, or clothing. Do not cut or weld metal containers. PESTICIDE STORAGE: Do not store below temperature of 45 °F. Store in safe manner. Store in original container only. Keep container tightly closed when not in use. Reduce stacking height where local conditions can affect package strength. Personnel should use cloth- ing and equipment listed under "PRECAUTIONARY STATEMENT" when handling open containers. PESTICIDE DISPOSAL: Pesticide wastes are acutely hazardous. Improper disposal of excess pesticide, spray mixture, or rinsate is a violation of Federal law. If these wastes cannot be disposed of by use according to label instructions, contact your State Pesticide or Environmental Control Agency, or the Hazardous Waste representative at the nearest EPA Regional Office for guidance. CONTAINER HANDLING: Nonrefillable container. Do not reuse this container to hold materials other than pesticides or dilute pesticides (rinsate). After empty- ing and cleaning, it may be allowable to temporarily hold rinsate or other pesticide-related materials in the container. Contact your state regulatory agency'to determine allowable practices in your state. Once cleaned, some agricultural plastic pesticide containers can be taken to a container collection site or picked up for recycling. To find the nearest site, contact your chemical dealer or manufacturer, or contact The Agricultural Container Recycling Council (ACRC) at www.acrecycle.org. If not recycled, then puncture and dispose of in a sanitary landfill, or incineration, or if allowed by state and local authorities, by burning. If burned, stay out of smoke. Triple rinse or pressure rinse container (or equivalent) promptly after emptying. (For packages up to 5 gallons:) Triple rinse as follows: Empty the remaining contents into application equipment or a mix tank and drain for 10 seconds after the flow begins to drip. Fill the container 1/4 full with water and recap. Shake for 10 seconds. Pour rinsate into application equipment or a mix tank or store rinsate for later use or disposal. Drain for 10 seconds after the flow begins to drip. Repeat this procedure two more times. Pressure rinse as follows: Empty the remaining contents into application equipment or a mix tank and continue to drain for 10 seconds after the flow begins to drip. Hold container upside down over application equipment or mix tank or collect rinsate for later use or disposal. Insert pressure rinsing nozzle in the side of the container, and rinse at about 40 PSI for at least 30 seconds. Drain for 10 seconds after the flow begins to drip. (For packages greater than 5 gallons or 50 IDS:) Triple rinse as follows: Empty the remaining contents into application equipment or a mix tank. Fill the container 1/4 full with water. Replace and tighten closures. Tip container on its side and roll it back and forth, ensur- ing at least one complete revolution, for 30 seconds. Stand the container on its end and tip it back and forth several times. Turn the container over onto its other end and tip it back and.forth several times. Empty the rinsate into application equipment or a mix tank or store rinsate for later use or disposal. Repeat this procedure two more times. Pressure rinse as follows: Empty the remaining contents into application equipment or a mix tank and continue to drain for 10 seconds after the flow begins to drip. Hold container upside down over application equipment or mix tank or collect rinsate for later use or disposal. Insert pressure rinsing nozzle in the side of the con- tainer, and rinse at about 40 PSI for at least 30 seconds. Drain for 10 seconds after the flow begins to drip. (For square bottom caged totes greater than 55 gals.): Triple rinse or pressure rinse as follows: Empty the remaining contents into application equipment or a mix tank and continue to drain for 10 seconds after the flow begins to drip. Fill the container about 1/4 full with water, rinsing down all sides inside the container thoroughly. Recirculate water with the pump for 2 minutes. Empty the rinsate 15

c c DIMETHOATE 400 EPA REG. NO. 34704-207 Storage & Disposal cont'd.: into application equipment or a mix tank or store rinsate for later use or disposal. Repeat this procedure two more times. (For refillable containers:) Refill this container with pesticide only. Do not reuse this container for any other purpose. Cleaning the con- tainer before final disposal is the responsibility of the person disposing of the container. Cleaning before refilling is the responsibility of the refiller. To clean the container before final disposal, empty the remaining contents from this container into application equipment or mix tank. Fill the container about 10 percent full with water. Agitate vigorously or recirculate water with the pump for 2 minutes. Pour or pump rinsate into application equipment or rinsate collection system. Repeat this rinsing procedure two more times. For help with any spill, leak, fire or exposure involving this material, call day or night CHEMTREC -1-800-424-9300. I? I? CONDITIONS OF SALE AND LIMITATION OF WARRANTY AND LIABILITY BEFORE BUYING OR USING THIS PRODUCT, read the entire Directions for Use and the following Conditions of Sale and Limitation of Warranty and Liability. By buying or using this product, the buyer or user accepts the following Conditions of Sale and Limitation of Warranty and Liability, which no employee or agent of LOVELAND PRODUCTS, INC. or the seller is authorized to vary in any way. Follow the Directions for Use of this product carefully. It is impossible to eliminate all risks inherently associated with the use of this prod- uct. Crop or other plant injury, ineffectiveness, or other unintended consequences may result from such risks as weather or crop condi- tions, mixture with other chemicals not specifically identified in this product's label, or use of this product contrary to the label instruc- tions, all of which are beyond the control of LOVELAND PRODUCTS, IMC. and the seller. The buyer or user of this product assumes all such inherent risks. Subject to the foregoing inherent risks, LOVELAND PRODUCTS, INC. warrants that this product conforms to the chemical description on the label and is reasonably fit for the purposes stated in the Directions for Use when the product is used in strict accordance with such Directions for Use under normal conditions of use. EXCEPT AS WARRANTED IN THIS LABEL AND TO THE EXTENT CONSISTENT WITH APPLICABLE LAW, THIS PRODUCT IS SOLD "AS IS," AND LOVELAND PRODUCTS, INC. MAKES NO OTHER WARRANTY, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR ELIGIBILITY OF THIS -PRODUCT-FOR-ANY-PARTICULAR TRADE USAGE: - - IN THE UNLIKELY EVENT THAT BUYER OR USER BELIEVES THAT LOVELAND PRODUCTS, INC. HAS BREACHED A WARRANTY CON- TAINED IN THIS LABEL AND TO THE EXTENT REQUIRED BY APPLICABLE LAW, BUYER OR USER MUST SEND WRITTEN NOTICE OF ITS CLAIM TO THE FOLLOWING ADDRESS: LOVELAND PRODUCTS, INC., ATTENTION: LAW DEPARTMENT, P.O. BOX 1286, GREELEY, CO 80632-1286. TO THE EXTENT CONSISTENT WITH APPLICABLE LAW, THE BUYER'S OR USER'S EXCLUSIVE REMEDY FOR ANY INJURY, LOSS, OR DAMAGE RESULTING FROM THE HANDLING OR USE OF THIS PRODUCT, INCLUDING BUT NOT LIMITED TO CLAIMS OF BREACH OF WARRANTY OR CONTRACT, NEGLIGENCE, STRICT LIABILITY, OR OTHER TORTS, SHALL BE LIMITED TO ONE OF THE FOLLOWING, AT THE ELECTION OF LOVELAND PRODUCTS, INC. OR THE SELLER: DIRECT DAMAGES NOT EXCEEDING THE PURCHASE PRICE OF THE PRODUCT OR REPLACEMENT OF THE PRODUCT. TO THE EXTENT CONSISTENT WITH APPLICABLE LAW, LOVELAND PRODUCTS, INC. AND THE SELLER SHALL NOT BE LIABLE TO THE BUYER OR USER OF THIS PRODUCT FOR ANY CONSEQUENTIAL, SPECIAL, OR INDI- RECT DAMAGES, OR DAMAGES IN THE NATURE OF A PENALTY. LI 700 is a registered trademark of Loveland Products, Inc. j FORMULATED FOR LOVELAND PRODUCTS, INC. P.O. BOX 1286, GREELEY, COLORADO 80632-1286 16