crop-chem-docs/corpus/epa_ppls/524-689.md

ROUNDUP D-PAK HERBICIDE

• EPA Reg No: 524-689
• Registrant: BAYER CROPSCIENCE, LLC
• Signal word: Caution
• Active ingredients: Glyphosate, isopropylamine salt (62%)
• Label accepted: 1999-11-04
• Source PDF: https://www3.epa.gov/pesticides/chem_search/ppls/000524-00494-19991104.pdf

---

PM EPA Reg. No. 524-494 ROUNDUP D-PAK Herbicide by Monsanto Complete Directions for Use J! ' 11;; r AVOID CONTACT OF HERBICIDE WITH FOLIAGE, GREEN STEMS, EXPOSED NON-WOODY ROOTS OR FRUIT OF CROPS (EXCEPT AS SPECIFIED FOR INDIVIDUAL ROUNDUP READY CROPS), DESIRABLE PLANTS AND TREES, BECAUSE SEVERE INJURY OR DESTRUCTION MAY RESULT Roundup is a registered trademark of Monsanco Co. Container Statement: Read "Limit of Warranty and Liability" which appears in the label booklet, before buying or using. If terms are not acceptable, rerum at once unopened. 21-Sep-1999 Page 1 of 66 Round~p D-Pak 99 revise.doc

Read the entire label before using this product. Use only according to label instructions. It is a violation of Federal law to use this product in any manner inconsistent with its labeling. Read the "LIMIT OF WARRANTY AND LIABILITY" statement at the end of the label before buying or using. If terms are not acceptable. return at once unopened. THIS IS AN END-USE PRODUCT. MONSANTO DOES NOT INTEND AND HAS NOT REGISTERED IT FOR REFORMULATION. SEE INDIVIDUAL CONTAINER LABEL FOR REPACKAGING LIMITATIONS. Conlainer Label Statemenl: THIS IS AN END-USE PRODUCT MONSANTO DOES NOT INTEND AND HAS NOT REGISTERED IT FOR REFORMULATION. IT IS INTENDED THAT REPACKAGING BE ONLY IN ACCORDANCE WITH A MONSANTO REPACKAGING OR TOLL REPACKAGING AGREEMENT. CONTENTS 1 1.0 INGREDIENTS 2 2.0 IMPORTANT PHONE NUMBERS 3 3.0 PRECAUTIONARY STATEMENTS 3.1 Hazards to Humans and Domestic Animals 3.2 Environmental Hazards 3.3 Physical or Chemical Hazards 4 4.0 STORAGE AND DISPOSAL 5 5.0 GENERAL INFORMATION (How this product works) 6 6.0 MIXING 6.1 Mixing with Water 6.2 Surfactant 6.3 Tank Mixing Procedure 6.4 Mixing for Hand-Held Sprayers 6.5 Ammonium Sulfate 6.6 Colorants or Dyes 6.7 Drift Control Additives 7 7.0 APPLICATION EQUIPMENT AND TECHNIQUES 7.1 Aerial Equipment 7.2 Ground Broadcast Equipment 7.3 Hand-Held and High-Volume Equipment 7.4 Selective Equipment (Wipers, etc.) 7.5 Injection Systems 7.6 CDA Equipment 8 8.0 CROPS (Alphabetical) 21-Sep-1999 Page 2 of 66 Roundup D-Pak 99 revise.doc

3] n 8.1 Alfalfa and Clover 8.2 Asparagus 8.3 Cereal Crops 8.4 Christmas Trees 8.5 Citrus Crops 8.6 Conservation Reserve Program (CRP) 8.7 Corn 8.8 Cotton 8.9 Fallow Systems 8.10 Grain Sorghum (Milo) 8.11 Grass Seed Production 8.12 Herbs 8.13 Pastures 8.14 Peanuts 8.15 Small Fruits and Berries 8.16 Soybeans 8.17 Sugarcane 8.18 Sunflowers 8.19 Tree and Vine Crops (General) 8.20 Tree Fruits 8.21 Tree Nuts 8.22 Tropical Crops 8.23 Vegetable Crops 8.24 Vine Crops 9 9.0 Roundup Ready Crops 9.1 Canola with the Roundup Ready Gene 9.2 Corn with the Roundup Ready Gene 9.3 Conon with the Roundup Ready Gene 9.4 Soybeans with the Roundup Ready Gene 9.5 Sugar beets with the Roundup Ready Gene 10 100 FARMSTEADS 10.1 General Weed Control and Trim-And-Edge 10.2 Chemical Mowing 10.3 Cut Stumps IDA Habitat Management \1 11.0 ANNUAL WEEDS RATE TABLE ALPHABETICALLY BY SPECIES I I. I Rates for !O to 40 GPA 11.2 Tank Mixtures with 2,4-D, Dicamba 12 12.0 PERENNIAL WEEDS RATE TABLE ALPHABETICALLY BY SPECIES 13 13.0 WOODY BRUSH AND TREES RATE TABLE ALPHABETICALLY BY SPECIES 14 14.0 LIMIT OF WARRANTY AND LIABILITY' 21-Sep-1999 Page 3 of 66 Roundup D-Pak 99 revise.doc

1.0 INGREDIENTS ACTIVE INGREDIENT: *Glyphosate, N-(phosphonomethyi) glycine, in the form of its isopropylamine salt ............................................................................. . OTHER INGREDIENTS: ................................................................................................... . ..... 62.0% 38.0% 100.0% 'Contains 769 grams per litre or 6.42 pounds per U.S. gallon of the active ingredient glyphosate, in the form of its isopropyl amine salt. Equivalent to 570 grams per litre or 4.75 pounds per U.S. gallon of the acid, gJyphosate. This proouct is protected by U.S. Patent No. 4,405,531. Other patents pending. No license granted under any non-U.S. patent(s). 2.0 IMPORTANT PHONE NUMBERS I. FOR PRODUCT INFORMATION OR ASSISTANCE IN USING THIS PRODUCT, CALL TOLL-FREE, 1-800-332-3111 2. IN CASE OF AN EMERGENCY INVOLVING TillS PRODUCT, OR FOR MEDICAL ASSISTANCE, CALL COLLECT, DAY OR NIGHT, (314)-694-4000 3.0 PRECAUTIONARY STATEMENTS 3.1 Hazards to Humans and Domestic Animals Keep out of reach of children. CAUTION! DOMESTIC ANIMALS: This product is considered to be relatively nontoxic to dogs and other domestic animals: however, ingestion of this prcx:luct or large amounts of freshly sprayed vegetation may result in temporary gastrointestinal irritation (vomiting, diarrhea. colic, etc.). If such symptoms are observed, provide the animal with plenty of fluids to prevent dehydration. Call a veterinarian if symptoms persist for more than 24 hours. Personal Protective Equipment (PPE) Applicators and other handlers mllSt wear: long-sleeved shirt and long pants. shoes plus socks. Follow manufacturer's instructions for cleaning/maintaining PPE (Personal Protective Equipment). If no such instructions for washables, use detergent and hot water. Keep and wash PPE separately from other laundry. 2l-Sep-1999 Page 4 of 66 Roundup D-Pak 99 revise.doc

\Vhen handlers use closed systems, enclosed cabs. or aircraft in a manner that meets the requirements listed in Worker Protection Standard (WPS) for agricultural pesticides [40 CFR 170.240 (d) (4-6)], the handler PPE requirements may be reduced or modified as specified in the WPS. User Safety Recommendations: Users should: • Wash hands before eating, drinking, chewing gum, using tobacco, or using the toilet. Remove clothing immediately if pesticide gets inside. Then wash thoroughly and put on clean clothing. 3.2 Environmental Hazards Do not apply directly to water, to areas where surface water is present or to intertidal areas below the mean high water mark. Do not contaminate water when disposing of equipment washwaters. 3.3 Physical or Chemical Hazards Spray solutions of this product should be mixed. stored and applied using only stainless steel. aluminum, fiberglass, plastic or plastic-lined steel containers. DO NOT MIX. STORE OR APPLY TIDS PRODUCT OR SPRAY SOLlITIONS OF THIS PRODUCT IN GALVANIZED STEEL OR UNLINED STEEL (EXCEPT STAINLESS STEEL) CONTAINERS OR SPRA Y TANKS. This product or spray solutions of this product react with such containers and tanks to prlXluce hydrogen gas which may form a highly combustible gas mixture. This gas mixture could flash or expltxle, causing serious personal injury, if ignited by open flame, spark, welder's torch, lighted cigarette or other ignition source. DIRECTIONS FOR USE It is a violation of Federal law to use this product in any manner inconsistent with its labeling. Do not apply this proouct in a way that will contact workers or other persons, either directly or through drift. Only protected handlers may be in the area during application. For any requirements specific to your State or Tribe, consult the agency responsible for pesticide regulations. Agricultural Use Requirements Use this product only in accordance with its labeling and with the Worker Protection Standard, 40 CFR part 170. This Standard contains requirements for the protection of agricultural workers on farms, forests, nurseries, and greenhouses, and handlers of agricultural pesticides. It contains requirements for training, decontamination, notitication, and emergency assistance. It also contains specific instructions and exceptions pertaining to the statements on this label about personal protective equipment (PPE) and restricted entry interval. The requirements in this box only apply to uses of this product that are covered by the Worker Protection Standard. 21-Sep-1999 Page 5 of 66 Roundup D-Pak 99 revise.doc

Do not enter or allow worker entry into treated areas during the restricted entry interval (REI) of 4 hours. PPE required for early entry 10 treated areas that is permilled under the Worker Protection Standard and that involves contact with anything that has been treated. such as plants, soil, or water, is:- coveralls, waterproof gloves, shoes plus socks. Non-Agricultural Use Requirements The requirements in this box apply to uses of this product that are NOT within the scope of the Worker Protection Standard for agricultural pesticides (40 CFR Part 170). The WPS applies when this product is used to produce agricultural plants on farms, forests, nurseries or greenhouses. Keep people and pets off treated areas until spray solution has dried (0 prevent transfer of this product onto desirable vegetation. 4.0 STORAGE AND DISPOSAL Do not contaminate water. foodstuffs. feed or seed by storage or disposal. See container label for STORAGE AND DISPOSAL instructions. Container Label Statements: (ALL CONTAINERS) Wastes reSUlting from the use of this product that cannot be used or chemically reprocessed should be disposed of in a landfill approved for pesticide disposal or in accordance with applicable Federal. state. or local procedures. Emptied container relains vapor and proouct residue. Observe all labeleD safeguards until conlainer is cleaned, reconditioned, or destroyed. (FOR REFILLABLE PORTABLE CONTAINERS) Do not reuse this conlainer except for refill in accordance with a valid Monsanto Repackaging or Toll Repackaging Agreement. If not refiIJed or returned to the authorized repackaging facility, triple rinse conrainer, then puncture and dispose of in a sanitary landfill, or by incineration, or, if allowed by state and local authorities. by burning. If burned. stay out of smoke. (FOR BULK CONTAINERS) Triple rinse emptied bulk container. Then offer for recycling Of reconditioning, or dispose of in a manner approved by stare and local authorities. (FOR PLASTIC I-WAY CONTAINERS & BOTILES) Do not reuse container. Triple rinse container. then puncture and dispose of in a sanitary landfill. or by incineration, or, if allowed by state and local authorities, by burning. If burned, stay out of smoke. (FOR DRUMS) Do not reuse container. Return container per the Monsanto container return program. If not returned, triple rinse container. then puncture and dispose of in a sanitary landfill. or by incineration. or. if allowed by state and local authorities, by burning. If burned. stay out of smoke. 21Sep1999 Page 6 of 66 Roundup D-Pak 99 revise. doc

5.0 GENERAL INFORMA TION (HOW THIS PRODUCT WORKS) Product Description: This product is a postemergent. systemic herbicide with no soil residual activity. It is generally non-selective and gives broad spectrum control of many annual weeds. perennial weeds, woody brush and trees. It is formulated as a water-soluble liquid. It may be applied through most standard industrial or field· type sprayers after dilution and thorough mixing with water or other carriers according to label instructions. This product requires the use of a nan ionic surfactant. When using this product, mix 2 or more quarts of a nanionic surfactant per 100 gallons of spray solution. The surfactant should contain at least 70 percent active ingredient. Time to Symptoms: This product moves through the plant from the point of foliage contact to and into the root system. Visible effects on most annual weeds occur within 2 to -l days, but on most perennial weeds may not occur for 7 days or more. Extremely cool or cloudy weather following treatment may slow activity of this product and delay development of visual symptoms. Visible effects are a gradual wilting and yellowing of the plant which advances to complete browning of above-ground growth and deterioration of underground plant parts. Stage of Weeds: Annual weeds are easiest to control when they are small. Best contra) of most perennial weeds is obtained when treatment is made at late growth stages approaching maturity. Refer to the annual, perennial, woody brush and trees rate tables for recommendations for specific weeds. Always use the higher rate of this product per acre within the recommended range when weed growth IS heavy or dense or weeds are growing in an undisturbed (noncullivared) area. Do not treat weeds under poor growing conditions such as drought stress, disease or insect damage, as reduced weed control may result. Reduced results may also occur when treating weeds heavily covered with dust. Cultural Considerations: Reduced control may result when applications are made to annual or perennial weeds that have been mowed, grazed, or cut, and have not been allowed to regrow to the recommended stage for treatment. Rainfastness: Heavy rainfall soon after application may wash this product otT of the foliage and a repeat application may be required for adequate control. Spray Coverage: For best results, spray coverage should be uniform and complete. Do not spray weed foliage to the point of runoff. Mode of Action: The active ingredient in this proouct inhibits an enzyme found only in plants and microorganisms that is essential to formation of specific amino acids. No Soil Activity: Weeds must be emerged at the time of application to be controlleJ by this product. Weeds germinating from seed after application will not be controlled. Unemerged plants arising from unattached underground rhizomes or root stocks of perennials will not be affected by the herbicide and will continue to grow. When this product comes in contact with soil. it is bound (0 soil particles. Under recommended use situations, once this product is bound to soil particles, it is not available for plant uptake and will not harm off-site vegetation where roots grow into the treated area or if the soil is transported off-site. The strong 21-Sep-1999 Page 7 of 66 Roundup D-Pak 99 revise.doc

aft1nity of this product to soil particles prevents this product from leaching out of the soil profile and entering ground water Biological Degradation: Degradation of this product is primarily a biological process carried out by soil microbes. Volatility: Roundup DPAK is non-volatile. Therefore. it cannot move as a vapor after application to affect nearby vegetation. Toxicology Testing: Exposure to workers and other applicators generally is expected to pose minimal risk based on results of shorHerm toxicity studies. Glyphosate has been thoroughly tested and determined nol to cause cancer or other adverse long-term health effects. Tank Mixing: This product does not provide residual weed controL For subsequent residual weed control. follow a fabeJ~approved herbicide program. Read and carefully observe the cJurionary ta£ernents and a/! other information appearing on the labels of aJJ herbicides used. Use according to the most restrictive label directions for each product in the mixture. Buyer and all users are responsible for all loss or damage in connection with the use or handling of mixtures of this proouct with herbicides or ocher materials chac are noc expressly recommended in this labeling. Mixing this product with herbicides or other materials not recommended on this label may result in reduced performance. Annual Maximum Use Rate: Except as otherwise specified in a crop section of this label, the combined total of all treatmems must not exceed 5 quarts of this product per acre per year. For noncrop uses, the combined total of all treatments must not exceed 6.7 quarts of this proouct per acre per year. NOTE: Use of this product in any manner nor consistent with this label may result in injury to persons, animals or crops. or other unintended consequences. 6.0 MIXING Clean sprayer parts immediately after using this product by thoroughly flushing with water. NOTE: reduced results may occur if water containing soil is used, such as visibly muddy water or water from ponds and ditches that is not clear. 6.1 Mixing with Water This product mixes readily with water. Mix spray solutions of this product as follows: Fill the mixing or spray lank with the required amount of water. Add the recommended amount of this product near the end of the filling process and mix well. Use caution to avoid siphoning back into the carrier source. Use approved anti­ back-siphoning devices where required by state or local regulations. During mixing and application, foaming of the spray solution may occur. To prevent or minimize foam, avoid the use of mechanical agitators, terminate by-pass and return lines at the bottom of the tank and. if needed, use an approved anti-foam or defoaming agent. 6.2 Surfactant 21-Sep-1999 Page 8 of 66 Roundup DPak 99 revise.doc

This product requires use of a non ionic surfactant. When using this product, mix 2 or more quarts of non ionic surfactant per 100 gallons of spray solution. The surfactant should contain at least 70 percent active ingredient. 6.3 Tank Mixing Procedure Mix labeled tank mixtures of this product with water as follows: I. Place a 20 to 35 mesh screen or welting basket over filling port. 2. Through the screen, fill the spray tank one-half fun with water and start agitation. 3. If a wettable powder is used, make a slurry with the water carrier, and add it SLOWLY thruugh the s.creen into the tank. Continue agitation. 4. If a tlowable formulation is used, premix one part flowable with one part water: Add diluted mixture SLO\VL Y through the screen into the tank. Continue agitation. 5. If an emulsifiable concentrate formulation is used, premix one part emulsifiable concentrate with two pans \valer. Add diluted mixture slowly through the screen into the tank. Continue agitation. 6. Continue tilling the spray tank with water and add the required amount of this product near the end of the filling process. 7, Add nonionic surfactant to the spray tank before completing the filling process. 8. Add individual formulations 10 the spray tank as follows: wettable powder, tlowable, emulsifiable concenfwre, drift conrro! additive and water soluble liquid. Maintain goc.x1 agitation at al1 times until the contents of the tank are sprayed. If the spray mixture i~ allowed to settle, thorough agitation is required to resuspend the mixture before spraying is resumed. Keep by-pass line on or near the bottom of the tank (Q minimize foaming. Screen size in nozzle or line strainers should be no finer than 50 mesh. Always predetermine the compatibility of labeled tank mixtures of this produce wirh water carrier by mixing small proportional quantiries in advance. Refer to the 'Tank Mixing" section of "GENERAL INFORMATION" for additional precautions. 6.4 Mixing for Hand-held Sprayers Prepare the desired volume of spray solution by mixing the amount of this product in water as shown in the following table: SQray Solution AmOUDi of Roundup D-PAK Desired Volume 1/3% 2/3% 1114% 31/2% 7% I Gal 1/2 oz loz I 2I30z 4 112 oz 90z 21-Sep-1999 Page 9 of 66 Roundup D-Pak 99 revise.doc

25 Gal 100 Gal \0 2/3 oz I 1/3 qt 210z 2213 qt I 1/4 qt 1 114 gal 3 1/2 qt 3 112 gal 2 tablespoons ~ I fluid ounce 7 qt 7 gal For use in knapsack sprayers, it is suggested that the recommended amount of this product be mixed with water in a larger container. Fill sprayer with the mixed solution. 6.5 Ammonium Sulfate The addition of I to 2 percent dry ammonium sulfate by weight or 8.5 to 17 pounds per 100 gallons of water may increase the performance of this product, particularly when tank mixed with certain residual herbicides on annual and perennial weeds. The equivalent rate of ammonium sulfate in a liquid formulation may also be used. Ensure that ammonium sulfate is completely dissolved in the spray tank before adding herbicides. Thoroughly rinse the spray system with clean water after use to reduce corrosion. NOTE: When using ammonium sulfate, apply this product at rates recommended in this labe. Lower rates will result in reduced performance. 6.6 Colorants or Dyes Agriculturally-approved colorants or marking dyes may be added to this product. Colorants or dyes used in spray solutions of this product may reduce performance. especially at lower rates or dilutions. Use colorants or dyes according to the manufacturer's recommendations. 6.7 Drift Control Additives Drift control additives may be used with all equipment types, except wiper applicators. sponge bars and CDA equipment. When a drift control additive is used. read and carefully observe the cautionary statements and all other information appearing on the additive labeL 7.0 APPLICA nON EQUIPMENT AND TECHNIQUES Do not apply this product through any type of irrigation system. This product may be applied with the following application equipment: Aerial--Fixed Wing and Helicopter Ground Broadcast Spray--Boom or boomless systems, pull-type sprayer, floaters, pick-up sprayers, spray coupes and other ground broadcast equipment. Hand-Held and High-Volume Spray Equipment--Knapsack and backpack sprayers, pump-up pressure sprayers, handguns, hand wands, mistblowers*, lances and other hand-held and motorized spray equipment used to direct the spray onto weed foliage. *This product is not registered in California or Arizona for use in mistblowers. Selective Equipment--Recirculating sprayers, shielded and hooded sprayers, wiper applicators and sponge bars. 21-Sep-1999 Page 10 of 66 Roundup D-Pak 99 revise doc

Injection Systems--Aerial or ground injection sprayers. Controlled Droplet Applicator (CDA)--Hand-held or boom-mounted applicators which produce a spray consisting of a narrow range of droplet sizes. Apply these spray solutions in properly maintained and calibrated equipment capable of delivering desired volumes. SPRAY DRIFT MANAGEMENT A VOID DRIFT. EXTREME CARE MUST BE USED WHEN APPLYING THIS PRODUCT TO PREVENT INJURY TO DESIRABLE PLANTS AND CROPS. DO NOT allow the herbicide solution to mist, drip. drift or splash onto desirable vegetation since minute quantities of this product can cause severe damage or destruction to the crop, plants or other areas on which treatment was not intended. Avoiding spray drift at the application site is the responsibility of the applicator. The interaction of many equipment-and-weather-reJated factors determine the potentia] for spray drift The applicator and the grower are responsible for considering all these factors when making decisions. 7.1 Aerial Equipment DO NOT apply this prcx1uct using aerial spray equipment except under conditions as specified within this label. Use the recommended nHes of this herbicide in 3 to 15 gallons of water per acre unless otherwise specified on this label. Unless otherwise specified, do not exceed 20 fluid ounces per acre. Aerial applications of this product may be made in unnual cropping conventional tillage systems, falJow and reduced tillage systems and preharvest application::., Refer to the individual use area sections of this label for recommended volumes, application rates and further instructions. Note: For aerial application in CALIFORNIA or ARKANSAS, refer to the federal supplemental label for aerial applications in that state for specific instructions, restrictions and requirements. For aerial applications, consult with state or local authorities regarding any additional requirements for aerial treatments. AERIAL SPRAY DRIFT MANAGEMENT The following drift management requirements must be followed to avoid off-target drift movement from aerial applications to agricultural field crops.

1. The distance of the outermost nozzles on the boom must not exceed % the length of the wingspan or rotor.
2. Nozzles must always point backward parallel with the air stream and never be pointed downwards more than 45 degrees. Where states have more stringent regulations, they should be observed. Importance of droplet size The most effettive way to redute drift potential is to apply large droplets. The best drift management strategy is to apply the largest droplets that provide sufficient coverage and control. Applying larger droplets reduces 21-Sep-1999 Page 11 of 66 RounQup D-Pak 99 revise.doc

drift potential, but will not prevent drift if applications are made improperly, or under unfavorable environmental conditions (see the Wind, Temperature and Humidity, and Temperature Inversion sections of this label). Controlling droplet size • Volume: Use high flow rate nozzles to apply the highest practical spray volume. Nozzles with the higher rated flows produce larger droplets. • Pressure: Use the lower spray pressures recommended for the nozzle. Higher pressure reduces dropJec size and does nol improve canopy protection. When higher flow fates are needed. use higher flow rate nozzles instead of increasing pressure. • Number of nozzles: Use the minimum number of nozzles that provide uniform coverage. • Nozzle orientation: Orienring nozzles so that the spray is released backwards. parallel !O the air~'re;Im, will produce larger droplets than other orientations. Significant deflection from the horizontal will reduce droplet size and increase drift potential. • Nozzle type: Use a nozzle type that is designed for the intended application. With most nozzle types, narrower spray angles produce larger droplets. Consider using low-drift nozzles. Solid stream nozzles oriented straight back produce larger droplets than other nozzle types. • Boom Length: For some use patterns, reducing the effective boom height to less than % of the wingspan or rotor length may further reduce drift without reducing swath width. • Application Height: Applications should not be made at a height greater than 10 feet above the top of the largest plants unless a greater height is required for aircraft safety. Making applications at the lowest height that is safe reduces the exposure of the droplets to evaporation and wind. Swath Adjustment When applications are made with a crosswind, the swath will be displaced downward. Therefore, on the up and downwind edges of the field, the applicator must compensate for this displacement by adjusting the path of the aircraft upwind. Swath adjustment distance should increase. with increasing drift potential (higher wind. smaller droplets. etc.). Wind Drift potential is lowest between wind speeds of 2 to iO mph. However, many factors, including droplet size and equipment type determine drift potential at any given speed. Application should be avoided below 2 mph due to variable wind direction and high inversion potential. NOTE: Local terrain can intluence wind patterns. Every applicator should be familiar with local wind patterns and how they affect spray drift. Temperature and Humidity When making applications in low relative humidity, set up equipment to produce larger droplets to compensate for evaporation. Droplet evaporation is most severe when conditions are both hot and dry. Temperature inversions Applications should not occur during a temperature inversion because drift potential is high. Temperature inversions restrict vertical air mixing. which causes small suspended droplets to remain in a 21-Sep-1999 Page 12 of 66 Roundup D-Pak 99 revise,doc

concentrated cloud, This cloud can move in unpredictable directions due to the light variable winds common during inversions. Temperature inversions are characterized by increasing temperatures with altitude and are common on nights with limited cloud cover and light to no wind. They begin to fonn as the sun sets and often continue into the morning. Their presence can be indicated by ground fog; however, if fog is not present, inversions can also be identified by the movement of smoke from a ground sautee or an aircrafr smoke generator. Smoke that layers and moves laterally in a concentrated cloud (under low wind conditions) indicates an inversion, while smoke that moves upward and rapidly dissipates indicates good vertical air mixing. Sensitive areas The product should only be applied when the potential for drift to adjacent sensitive areas (e.g. residential areas, bodies of water, known habitat for threatened or endangered species, non-target crops) is minimal (e.g. when wind is blowing away from the sensitive areas). Avoid direct application to any body of water. Ensure uniform application--To avoid streaked. uneven or overlapped application. use appropriate marking devices. Thoroughly wash aircraft, especially landing gear. after each day of spraying to remove residues of this product accumulated during spraying or from spills. PROLONGED EXPOSURE OF THIS PRODUCT TO UNCOATED STEEL SURFACES MAY RESULT IN CORROSION AND POSSIBLE FAILURE OF THE PART. LANDING GEAR ARE MOST SUSCEPTIBLE. The maintenance of an organic coating (paint), which meets aerospace specification MIL-C-384 I 3. may prevent corrosion. Banvel tank mixtures may not be applied by air in California. 7.2 Ground Broadcast Equipment Use the recommended rates of this product in 3 to 40 gallons of water per acre as a broadcast spray unle~s otherwise specitied. As density of weeds increases, spray volume should be increased within the recom­ mended range (0 ensure complete coverage. Carefully select proper nozzles to avoid spraying a tine mise For best res.ults with ground application equipment, use flat fan nozzles. Check for even distribution of spray droplets. 7.3 Hand-Held and High-Volume Equipment Apply to foliage of vegetation to be controlled. For applications made on a spray-to-wet basis, spray coverage should be uniform and complete. Do not spray to the point of runoff. Use coarse sprays only. Refer to Section 6.0 "MIXING" in this label for more information on preparing spray solutions of cenain percentage content. For control of weeds listed in the annual weeds rate tables. apply a 113 percent solution of this product to weeds less than 6 inches in height or runner length. Apply prior to seedhead formation in grass or bud formation in broadleaf weeds. For annual weeds over 6 inches tall, or unless otherwise specitied, use a 2/3 percent solution. For best results, use a 1 1/4 percent solution on harder-to-control perennials. such as bermudagrass, dock, 'Iield bindweed. hemp dogbane. milkweed and Canada thistle. 21-Sep-1999 Page 13 of 66 Roundup D-Pak 99 revise.doc

When using application methoos which result in less than complete coverage, use a 3 112 percent solution for annual and perennial weeds and a 3 112 to 7 percent solution for woody brush and trees. 7.4 Selective Equipment This product may be applied through recirculating spray systems, shielded applicators, hooded sprayers, wiper applicators or sponge bars after dilution and thorough mixing with water to listed weeds gro~,'ing in any noncTop site specified on this label and only when specifically recommended in cropping systems. A recirculating spray system directs the spray solution onto weeds growing above desirable vegetation, while spray solution not intercepted by weeds is collected and returned to the spray tank for reuse. A shielded or hooded applicator directs the herbicide solution onto weeds, while shielding de:-,irab!e vegefmion from the herbicide. A wiper or sponge applicator applies the herbicide solution onto weeds by rubbing the weed with an aborbcnt material conraining the herbicide solution, A VOID CONTACT OF HERBICIDE WITH DESIRABLE VEGETATION. Contact of the herbicide solution with desirabe vegetation may result in damage or destruction. Applicators used above desirable vegetation should be adjusted. so that the lowest spray stream or wiper contact point is at leas[ 2 inches above [he desirable vegetation. Droplets, mist, foam or splauer of the herbicide solution settling on desirable vegetation may resuh in discoloration, stunting or destruction. Applications made above [he crops should be made when the weeds are a minimum of 6 inches aoove the desirable vegetation. Better results may be obtained when more of the weed is exposed to the herbicide solution. Weeds not contacted by the herbicide solution will not be affected. This may occur in dense clumps, severe infestations or when the height of the weeds varies so that not all weeds are contacted. In these instances, repeat treatment may be necessary. Shielded and hooded applicators Use nozzles that provide uniform coverage within the treated area. Keep shields on these sprayers adjusted to protect desirable vegetation. EXTREME CARE MUST BE EXERCISED TO A VOID CONTACT OF HERBICIDE WITH DESIRABLE VEGETATION. A hooded sprayer is a type of shielded applicator. The spray pattern is completely enclosed un the top and all 4 sides by a hood, thereby shielding the crop from the spray solution. This equipment must be set up and operated in a manner that avoids bouncing or raising the hoods off the ground in any way. If the hcxx!s are raised. spray particles may escape and come into contact with the crop, causing damage or destruction of the crop. The spray hoods must be operated on the ground or skimming across the ground. Tractor speed must be adjusted to avoid bouncing of the spray hoods. Avoid operation on rough or sloping ground where the spray hoods might be raised off the ground. Wiper applicators and sponge bars Wiper applicators are devices that physically wipe appropriate amounts of this product directly onto the weed. Equipment must be designed, mainfained and operated. to prevent the herbicide solution from contacting desirable vegetation. Operate this equipment at ground speeds no greater than 5 mph. Performance may be 21-Se.p-1999 Page 14 of 66 Roundup D-Pak 99 revise doc

improved by reducing speed in areas of heavy weed infestations to ensure adequate wiper saturation. Beller results may be oblained jf 2 applications are made in opposite directions. Avoid leakage or dripping onto desirable vegetation. Adjust height of applicator to ensure adequate contact with weeds. Keep wiping surfaces clean. Be aware that, on sloping ground, the h'erbicide solution may migrate, causing dripping on the lower end and drying of the wicks on the upper end of a wiper applicator. Do not use wiper equipment when weeds are wet. Mix only the amounl of s.olution to be used during a l-day period, as reduced activilY may result from use of leftover solutions. Clean wiper parts immediately after using this product by thoroughly flushing with water. Nonionic surfacran( at a fate of 10 percent by volume of total herbicide solution is recommended v., .. ith all wiper applications. For Rope or Sponge \'ick Applicators--Mix 2.5 quarts of this proouct in 2 gallons of water plus 1 quart of nan ionic surfactant. Apply this solution to weeds listed in this section. For Porous-Plastic Applicators--SoJutions ranging from 25 to 75 percent of this product in water may be used in porous-plastic wiper applicators. When applied a' recommended, this product CONTROLS the following weeds: Corn, volunteer Panicum, Texas Rye, common Shattercane Sicklepod Spanishneedles Starbur, bristly When applied as recommended, this product SUPPRESSES the following weeds: Beggarweed. Florida Bermudagrass Dogbane, hemp Dogfennel Guineagrass Johnsongrass Milkweed Nightshade, silverleaf Pigweed. redroot 7.5 Injection Systems Ragweed, common Ragweed, giant Smutgrass Sunflower Thistle, Canada Thistle, musk Vaseygrass Velvetleaf This product may be used in aerial or ground injection spray systems. It may be used as a liquid concentrate or diluted prior to injecting into the spray stream. Do not mix this product with the concentrate of other products when using injection systems. 7.6 CDA Equipment The rate of this product applied per acre by vehicle-mounted CDA equipment must not be less than the amount recommended in this label when applied by conventional broadcast equipment. For vehicle-mounted CDA equipment, apply 2 to 15 gallons of water per acre. For the control of annual weeds with hand-held CDA units, apply a 12.5 percent solution of this product at a flow rate of 2 fluid ounces per minute and a walking speed of 1.5 mph (20 fluid ounces per acre). For the 21-Sep-1999 Page 15 of 66 Roundup D~Pak 99 revise.doc

control of perennial weeds. apply a 12.5 to 25 percent solution of this product at a flow rate of 2 fluid ounces per minute and a walking speed of 0.75 mph (40 fluid ounces to 2.5 quarts per acre). Controlled droplet application equipment produces a spray pattern which is not easily visible. Extreme care must be exercised to avoid spray or drift contacting the foliage or any other green tissue of desirable vegetation, as damage or destruction may result. 8.0 CROPS (Alphabetical) This section is organized alphabetically by crop category. There may be several labeled crops listed in a crop category. Unless orherwise specified, applications may be made to control any weeds listed in the annual, perenniJI and woody brush tables. Also refer to the "SELECTIVE EQUIPMENT" section. For any crop not listed in this "CROPS" seclion, appJications must be made at least 30 days prior to planljng. See Section 9.0 "ROUNDUP READYQll CROPS" for use of this product in crops that contain the Roundup Ready gene. DO NOT use the instructions in this "CROPS" Section. For broadcast postemergent treatments, do not harvest or feed treated vegetation for 8 weeks follo\lv;ng application, unless otherwise specified. When applying this product prior to transplanting crops into plastic mulch, care must be taken to remove residues of this product, which could cause crop injury. from the plastic prior to transplanting. Residues can be removed by a single 0.5 inch application of water. either by natural rainfall or via a sprinkler system. Applicarions made at emergence will result in injury or death to emerged seedlings. 8.1 Alfalfa, Clover, and Other Forage Legumes LABELED CROPS: Alfalfa. clover. kudzu. lespedeza. lupin. sainfoin. trefoil. velvet bean. vetch, crown vetch, milk vetch TYPES OF APPUCA TIONS: Preplant. preemergence. at-plan ling. preharvest (Alfalfa only), spot treatment (alfalfa and clover only). wiper applicators (alfalfa and clover only). renovation Preplant, Preemergence and At-planting USE INSTRUCTIONS: This product may be applied before. during or after planting crops listed in this section. Applications must be made prior to emergence of the crop. PRECAlITIONS. RESTRlCTIONS: Remove domestic livestock before application and wait 8 weeks after application before grazing or harvesting. Preharvest (Alfalfa only) USE INSTRUCTIONS: This product may be used in declining alfalfa stands or any stand of alfalfa where crop destruction is acceptable. This application will severely injure or destroy Ihe stand of alfalfa. This product will control annual and perennial weeds, including quackgrass. when applied prior to the harvest of alfalfa. The treated crop and weeds can be harvested and fed to livestock after 36 hours. Allow a minimum of 36 hours between application and harvest. Applications may be made at any time of the year. Make only one application to an existing stand of alfalfa per year. For control of quackgrass, apply in the spring. late 21-Sep-1999 Page 16 of 66 Roundup D-Pak 99 revise.doc

summer or fall when quack grass is actively growing. Treatments for quackgrass must be followed by deep tillage for complete control. PRECAUTIONS, RESTRICTIONS: Do not apply more than 20 fluid ounces of this product per acre as a pre harvest treatment. Do not use for alfalfa grown for seed, as a reduction in germination or vigor may occur. Spot treatment or Wiper applications (Alfalfa and Clover only) USE INSTRUCTIONS: This product may be applied as a spot treatment in alfalfa or clover. This product may be applied with wiper applicators to control or suppress the weeds listed under "WIPER APPLICATORS" in the "SELECTIVE EQUIPMENT" section of this label. Applications may be made in the same area at 30-day intervals. PRECAUTIONS, RESTRICTIONS: For spot treatment and wiper applications, apply in areas where the movement of domestic livestock can be controlled. No more than one-tenth of any acre should be treated at one time. Remove domestic rivestock before application and wait 14 days after application before grazing livestock or harvesting. Renovation USE INSTRUCTIONS: This product may be applied as a broadcast spray to existing stands of alfalfa, clover, and other labeled forage legumes. Labeled crops may then be planted into the treated area. PRECAUTIONS, RESTRICTIONS: Remove domestic livestock before application and wait 8 weeks after application before grazing or harvesting. 8,2 Asparagus TYPES OF APPLICATIONS: Preplant, preemergence, spot treatment, postharvest Preplant, Preemergence USE INSTRUCTIONS: This product may be applied prior to emergence of asparagus. PRECAUTIONS, RESTRICTIONS: Do nor apply within a week betore the lirst spears emerge. Spot treatment USE INSTRUCTIONS This product may be applied immediately after cutting, but prior to the emergence of new spears. PRECAUTIONS, RESTRICTIONS: Do nor treat more than 10 percent of the total lield area to be harvested. Do not harvest within 5 days of treatment. Postharvest USE INSTRUCTIONS: This product may be applied after the last harvest and all spears have been removed. If spears are allowed to regrow, delay application until ferns have developed, Delayed treatments should be applied as a directed or shielded spray in order to avoid contact of the spray with ferns, stems or spears. PRECAlmONS, RESTRICTIONS: Direct contact of the spray with the asparagus may result in serious crop injury. Select and use recommended types of spray equipment for postemergence postharvest applications, A directed spray is any application where the spray pattern is aligned in such a way as to avoid direct contact of 21-Sep-1999 Page 17 of 66 Roundup D-Pak 99 revise.doc 17618

the spray with the crop. A shielded spray is any application where a physical barrier is positioned and maintained between the spray and the crop to prevent contact 'of spray with the crop. 8.3 Cereal Crops LABELED CROPS: Barley. Buckwheat, Millet (Pearl, Proso), Oats, Rice, Rye, Teosinte, Triticale, Wheal (All), Wild rice TYPES OF APPUCATIONS: Preplant, preemergence, at-planting, spot treat men! (except rice), post·harvest, preharves[ (wheat only), wiper applicators (wheat only). Red rice control prior to planting rice Do not treat rice fields or levees when the field contains flood water. Preplant, Preemergence and At-planting USE INSTRUCTIONS: This product may be applied before, during or after planting of cereal crops. Applications must be made prior 10 emergence of the crop. Spot treatment (except rice) USE INSTRUCTIONS: This product may be applied as a spot treatment in cereal crops, Apply this product before heading in small grains. PRECAUTIONS, RESTRICTIONS: Do not treat more than 10 percent of the total field area to be harvested. The crop receiving spray in the treated area wi)) be killed. Take care to avoid drift or spray outside target area for the same reason. Postharvest USE INSTRUCTIONS: This product may be applied after harvest of cereal crops. Higher rates may be required for control of large weeds which were growing in the crop at the time of harve\t. Tank mixtures with 2,4-D or dicamba may be used. PRECAUTIONS, RESTRICTIONS: For any crop not listed on this label, applications must be made at least 30 days prior 10 planting the next crop. Do not harvest or feed treated vegetation for g weeks following applicalion. Preharvest (wheat only) USE INSTRUCTIONS: This product provides weed control when applied prior ro harvest of wheat. Apply after the hard-dough stage of grain (30% or less grain moisture) and at least 7 days prior to harvest. Wheat stubble may be grazed immediately after harvest. This product may be applied using either aerial or ground spray equipmen'. For ground applications, apply this product in 10 to 20 gallons of water per acre, For aerial applications, apply this product in 3 to 10 gallons of water per acre. PRECAUTIONS, RESTRICTIONS: Do not apply more than 20 fluid ounces of this product per acre. Do not apply to wheat grown for seed, as a reduction in germination or vigor may occur. 'Wiper applications (wheat only) 21-Sep-1999 Page 18 of 66 Roundup D-Pak 99 reviSE.doc

USE INSTRUCTIONS: Wiper applications may be used in wheat. To control common rye or cereal rye, apply after the weeds have headed and achieved maximum growth, when the rye is at least 6 inches above the wheat crop. PRECAUTI01\S, RESTRICTIONS: Allow at least 35 days between application and harvest. Do not use roller appl icators. Red rice control prior to planting rice USE INSTRUCTIONS: Apply I quart of this product in 5 to 10 gallons of water per acre. Flush fields prior to application !O obrain uniform germination and stand of red rice. Make application when the majority of the red rice plailts are in the 2-leaf stage and no more than 4 inches tall. Red rice plants with less than 2 true leaves may be only p;:mialJy controlled. PRECAUTJO:'i. RESTRICTIONS: Avoid spraying during low humidity conditions, as reduced control ma, result. Do no! ;reat rice fields or levees when the fields contain water. Do not re-tlcxxf treated fields for 8 days following appjicarion. 8.4 Christmas Trees TYPES OF APPLlCA TIONS: Post-directed, spot treatment, site preparation Post-directed, Spot treatment USE INSTRGCTIONS: This product may be used as a post-directed spray and spot treatment around established ChrIstmas trees. PRECAUTIO:\S. RESTRICTIONS: Desirable plants may be protected from the spray solution by using shields or w,oflngs made of cardboard or other impermeable material. THIS PRODUCT IS NOT RECOMME1\DED FOR USE AS AN OVER-THE-TOP BROADCAST SPRAY IN CHRISTMAS TREES. Care must be c\Cfcised to avoid contact of spray, drift or mist with foliage or green bark of established Christmas tree~. Site preparation USE INSTRCCTIONS: This product may be used prior to planting Christmas trees. PRECAUTIO\S, RESTRICTIONS: Precautions should be taken to protect nontarget plants during site preparation applications. 8.5 Citl""us Crops LABELED CROPS: Calamondin, Chironja, Citron, Citrus Hybrids, Grapeli-uit, Kumquat, Lemon, Lime, Mandarin (tanf:erine). Orange (All), Pummelo. Tangelo. Tangor TYPES OF APPLICATIONS: General weed contrOl, middles (between rows of trees), strips (in row of trees), selective equipmenr NOTE: For general use directions, see the "TREE, NUT AND VINE (GENERAL)" section. The following directions are specific to citrus crops. 21-Sep-199, Page 19 of 66 Roundup D-Pak 99 revise.doc

Florida and Texas only: For burndown or conlrol of the weeds listed below. apply Ihe recommended rales of this product in 3 to 30 gallons of water per acre. Where weed foliage is dense. use 1010 30 gallons of water per acre. For goatweed. apply I 1/4 to 2 quarts of this product per acre. Apply in 20 to 30 gaftons of water per acre when plants are aClively growing. Use I )/4 quarts per acre when plants are less than 8 inches tall and 2 quarts per acre when plants are greater than 8 inches tall. If goat weed is greater than 8 inches tall, the addition of Krovar m II or Karmexn~ may improve control. Refer to the individual product labels for specitic crops, rates, geographic restrictions and precautionary statements. Perennial weeds: S = Suppression PC = Partial control WEED SPECIES Bermudagrass Guineagrass Texas and Florida Ridge Florida Flatwoods Paragrass Torpedograss B = Bumdown C = Control ROUNDUP D-PAK RATE PER ACRE 1/3 QT I 1/4 QT 2 QT 3.2 QT B B S B C B C C C C PC PC C C C C C PRECAUTIONS. RESTRICTIONS: Allow a minimum of I day between last application and harvest. 8.6 Conservation Reserve Program (CRP) TYPES OF APPLICATIONS: Renovation (rotating out of CRP). site preparation. postemergence weed control in dormant eRP grasses, wiper Rotating out of CRP, Site preparation USE INSTRUCTIONS: This product may be used to prepare CRP land for crop production. Postemergence weed control in dormant CRP grasses, Wiper USE INSTRUCTIONS: This product may be used to suppress competitive growth and seed production of undesirable vegetation in CRP acres. Such applications may be made with wiper application equipment or as a broadcast or spot treatment to dormant CRP grasses. For selective applications with broadcast spray equipment, apply 8 to 10 t1uid ounces of this product per acre in early spring before desirable CRP grasses. such as crested and tall wheatgrass. break dormancy and initiate green growth. Late fall applicalions can be made after desirable perennial grasses have reached dormancy. PRECAUTIONS. RESTRICTIONS: Some stunting of eRP perennial grasses will OCcur if broadcast applications are made when plants are not dormant. 8.7 Com 21-Sep-1999 Page 20 of 66 Roundup D-Pak 99 revise.doc

TYPES OF CORN: Field corn, seed corn, sweet corn and popcorn TYPES OF APPLICATIONS: Preplant, preemergence, at-planting, sPot treatment, hooded sprayers, preharvest, post-harvest. For Roundup Ready corn, see the Roundup Ready Section of this label. Preplant, Preemergence and At-Planting USE INSTRUCTIONS: This product may be applied before, during or after planting corn. Applications must be mnde prior to emergence of the crop. The following tank mixtures may be applied before, during or after planting in conventional tillage systems, into a cover crop, established sod or in previous crop residue. Apply these tank mixtures in 10 to 20 gallons of water or 10 to 60 gallons of nitrogen solution per acre. For Southern stales. do nol apply in nitrogen solutions to tough-to-control gra~ses such as barnyardgrass, fall panicum, broadleaf signaigrass, annual ryegrass and any perennial weeds. See the map in the Annual Weeds section of this label for areas included in this recommendation. ATRAZINE EXTRAZlNE'M LOROX'M BANYEL FRONTIER'M MARKSMAN'M BICEP'M GUARDSMAN'M MICRO-TECH® BICEP II HARNESS® PARTNER® BLADEXICY ANAZlNE HARNESS XTRA PROWL'M BROADSTRIKE'M HARNESS XTRA 5.6L SIMAZINE BULLET® LARIAT® SURPASS'M DUAL'M LASSO®I ALACHLOR SURPASS I ()() DUAL II LINEX'M TOPNOTCH'M For improved burndown, this product may be tank mixed with 2,4-D or dicamba. Annual weeds--For difficult-to-control weeds such as fall panicum, barnyardgrass, crabgrass, shatlercane and broad leaf signalgrass up to 2 inches tall, and Pennsylvania smartweed up to 6 inches tall, apply this product at 20 fluid ounces per acre in these tank mixtures. For other labeled annual weeds, apply 10 to 15 fluid ounces of this product per acre when weeds are less than 6 inches tall, and 20 to 30 fluid ounces when weeds are over 6 inches tall. PRECA UTJONS, RESTRICTIONS: Applications of 2,4-D or dicamba must be made at least 7 days prior to planting corn. The rank mix recommendations in chis seceion are nor registered in California. Hooded Sprayers USE INSTRUCTIONS: This product may be used through hooded sprayers for weed control between the rows of corn. Only hooded sprayers that completely enclose the spray pattern may be used. When applying to corn that is grown on raised beds, ensure that the hcxx:i is designed to completely enclose the spray solution. If necessary, extend the front and rear flaps of the hcxx:is to reach the ground in deep furrows. Follow these requiremems: • The spray hoods must be operated on the ground or skimming across the ground. • Do not apply more than 20 fluid ounces of this product per acre per application. 21-Sep-1999 Page 21 of 66 Roundup D-Pak 99 revise. doc

• Corn must be at least 12 inches tali, measured without extending leaves. • Leave at least an 8 inch untreated strip over the drill row. For example, if the crop row width is 38 inches, the maximum width of the spray hood should be 30 inches. • Maximum traclOr speed: 5 mph. • Maximum wind speed: 10 mph. • Use low-drift nozzles. Crcp injury may occur when the foliage of treated weeds comes into direct contact with leaves of the crop. Do not apply this product when the leaves of the crop are growing in direct contact with weeds to be treated. Droplets. mist, foam or splatter of the herbicide solution may contact the crop and cause discoloration, stunting or destruction. PRECAUTIONS, RESTRlCTlONS: Contact of this product in any manner to any vegetation to which treatment in not intended may cause damage. Such damage shall be the sole responsibility of the applicator Allow a minimum of 7 days between application and grazing or harvest. Do not apply more than 2 quart., of this product per acre per year for hooded sprayer applications. Spot treatment USE INSTRUCTIONS: For spot treatments, apply this product prior 10 silking of corn. PRECAUTIONS, RESTRlCTIONS: Do not treat more than 10 percent of the total field area to be harvesteD. The crop receiving spray in the treated area will be killed. Take care to avoid drift or spray outside target area for the same reason. Preharvest USE INSTRUCTIONS: Make applications at 35 percent grain moisture or less. Ensure that maximum kernel fIIi is complete and the corn is physiologically mature (black layer formed). For ground applications, apply up to 2 quarts of this product per acre. For aerial applications, apply up to 20 fluid ounces of this product per acre .. PRECAUTIONS, RESTRlCTlONS: Allow a minimum of 7 days between application and harvest 11 is not recommended thac corn grown for seed be treated because a reduction in germinarion Or vigor may result. Post-harvest USE INSTRUCTIONS: This product may be applied afler harvest of corn. Higher rates may be required for control of large weeds which were growing in the crop at the cime of harvest. Tank mixtures with 2,4-D or dicamba may be used. PRECAUTIONS, RESTRlCTIONS: Do not harvest or feed treated vegetation for 8 weeks following application. 8,8 Cotton TYPES OF APPLICATIONS: Preplant, preemergence, at-planting, hooded sprayer, selective equipment, spot treatment, preharves!. For Roundup Ready Calion, see the Roundup Ready Section of this label. Preplant, Preemergence, and At-planting 21-Sep-1999 Page 22 of 66 Roundup D-Pak 99 revise,doc

USE INSTRUCTIONS: This product may be applied before, during or after planting cotton. Applications must be made prior to emergence of the crop. Hooded sprayer, Selective equipment USE INSTRUCTIONS: This product may be applied through hooded sprayers, recirculating sprayers, shielded applicators or wiper applicators in coUon. PRECAUTIONS, RESTRlCTIONS: See the "SELECTIVE EQUIPMENT" part of the "APPLICATION EQlJJPMENT AND TECHNlQUES" section of this label for information on proper use and calibration of this equipment. Allow at least 7 days between application and harvest. Spot treatment USE INSTRUCTIONS: For spot treatments, apply this product prior to boll opening of COllon. PRECAUTIONS, RESTRlCTIONS: Do not treat more than 10 percent of the total field area to be harvested. The crop receiving spray in treated area will be killed. Take cafe to avoid drift or spray outside target area for the same reason. Prcharvest USE INSTRUCTIONS: This product provides weed control and cotton regrowth inhibition when applied prior to harvest of coHon. For weed control, apply at rafes given in the annual, perennial and woody brush tables. Apply to to 40 fluid ounces of this product per acre for cotton regrowth inhibition. Allow a minimum of 7 days between application and harvest of cotton. This product may be applied using either aerial or ground spray equipment. For ground applications, apply this proouct in 10 to 20 gallons of water per acre. For aerial applications, apply this proouct in 3 to 10 gallon.'. of water per acre. Apply after sufficient bolls have developed to produce the desired yield of cotton. Applications made prior to this time could affect maximum yield potential. This pnxiuct may be tank mixed with DEF 6, FoJexTl.A, or PrepT~ 10 provide additional enhancement of cotton leaf drop. PRECAUTIONS. RESTRICTIONS: Do nor feed or graze treared cotton forage or hay following preharvesr applications. Applications up to 40 tluid ounces per acre per year of this product may be applied by ground or air at preharvest timing. Do not exceed this amount. Do not apply to cotton grown for seed, as a reduction in germination or vigor may occur. 8,9 Fallow Systems TYPES OF APPLICATIONS: Chemical fallow, preplant fallow beds, aid-to-tillage Chemical fallow USE INSTRUCTIONS: This product may be applied during the fallow period prior to planting or emergence of any crop listed on this label. For any crop not listed on this label, applications must be made at least 30 days prior to planting. This product may be used as a substitute for tillage to control annual weeds in fallow 21-Sep-1999 Page 23 of 66 Roundup D-Pak 99 revise.doc

fields. Also, broadcast or spot treatments will control or suppress many perennial weeds in fallow fields. Ground or aerial application equipment may be used. Tank mixtures with 2,4-D and dicamba may be used. PRECAUTIONS, RESTRICTIONS: Do not apply Banvel tank mixtures by air in California. Refer to the specific proouct labels for crop rotation restrictions and cautionary statements of all 'products used in lank mixtures. Some crop injury may occur if Banvel is applied within 45 days of planting. Preplant fallow beds USE INSTRUCTIONS: This product may be applied to fallow beds prior to planting or emergence of any crop listed on this label. For any crop not listed on this label, applications must be made at least 30 days prior to planting. This product will control weeds listed in the annual, perennial and woody brush tables. In addition, g fluid ounces of this proouct plus 2 to 4 oz of Goal™ 2XL per acre will control the following weeds with the maximum heighr or lengrh indicated: 3" -- common cheeseweeJ, chickweed, groundsel: 6"-­ London rocket, shepherd's-purs..". 10 t1uid ounces of this product plus 2 to 4 oz of Goal 2XL per acre will control the following weeds with the maximum height or length indicated: 6" -- common cheeseweed, groundsel, marestail (Coll),za canadensis), 12" -- chickweed, London rocket, shepherd's-purse. Aid-to-tillage USE INSTRUCTIONS: This product may be used in conjunction with tillage practices in fallow systems or preplant to labeled crops to control downy brome, cheat, volunteer wheat, tansy mustard and foxtail. Apply 5 fluid ounces of this product in 3 to 10 gallons of water per acre. Make applications before weeds are 6 inches in heighr. Application must be followed by conventional tillage practices no later than 15 days arrer treatment and before regrowth occurs. Allow at least 1 day after application before tillage. PRECAUTIONS. RESTRICTIONS: Tank mixtures with residual herbicides may result in reduced performance. 8.10 Grain Sorghum (Milo) TYPES OF APPUCA nONS: Preplant. preemergence, at-planting. spot treatment. wiper applicators, hooded sprayers, preharvest, post-harvest Preplant, Preemergence, At-planting USE INSTRUCTIONS: This product may be applied before, during or after planting grain sorghum. Applications must be made prior to emergence of the crop. Spot treatment and Wiper applications USE INSTRUCTIONS: This product may be applied as a spot treatment in grain sorghum. Make spot treatments before heading of milo. This product may be applied with wiper applicators to control or suppress the weeds listed under "WIPER APPUCA TORS" in the "SELECTIVE EQUIPMENT" section of this label. PRECAUTIONS, RESTRICTIONS: For spot treatment, do not treat more than 10 percent of the total field area to be harvested. The crop receiving spray in treated area will be killed. Take care to avoid drift or spray outside target area for the same reason. 21-Sep-1999 Page 24 of 66 Roundup D-pak 99 revi~e.doc

) For wiper applicators, allow at least 40 days between application and harvest. Do not use roller applicato". Do not feed or graze treated milo fodder. Do not ensile treated vegetation. Hooded Sprayers USE INSTRUCTIONS: This product may be used through hooded sprayers for weed control between the rows of milo. Only hooded sprayers that completely enclose the spray pattern may be used. When applying to milo that is grown on raised beds, ensure that the hood is designed to completely enclose the spray solution. If necessary, extend the front and rear flaps of the hoods to reach the ground in deep furrows. Follow these requirements: • The "pr<lY hoods must be operated on the ground or skimming across the ground. • Do nor apply more than 20 tluid ounces of this product per acre per application. • Milo must be at least 12 inches tall. measured without extending leaves. Treat before milo sends tillers between the drill rows. If such tillers are contacted with the spray solution, the main plant may be killed • Leave at least an 8 inch untreated strip over the drill row. For example. if the crop row width is 38 inc he" the maximum width of the spray hood should be 30 inches, • Maximum tractor speed: 5 mph. • Maximum wind speed: 10 mph. • Use low-drift nozzles. Crop injury may occur when the foliage of treated weeds comes into direct contact with leaves of the crop. Do nOl apply this product when the leaves of the crop are growing in direct contact with weed, to be treated. Droplets, mist, foam or splatter of the herbicide solution may contact the crop and cause discoloration, stunting or destruction. PRECAUTIONS, RESTRlCTIONS: Contact of this product in any manner to any vegetation to which treJ.tment in not intended may cause damage. Such damage shall be the sole responsibility of the applicator. Do nOI graze or feed milo forage or fodder following applications of this product through hooded sprayers.. Do not apply more than 2 quarts of this product per acre per year for hooded sprayer applications. Preharvest USE INSTRUCTIONS: Make applications at 30% grain moi'ture or less. PRECAUTIONS, RESTRlCTIONS: Do not apply more than 40 tluid ounces of this product per acre. Allow a minimum of 7 days between application and harvest of sorghum. It is not recommended that sorghum grown for seed be treated, as a reduction in germination or vigor may occur. The use of this product for preharvest grain sorghum (Milo) is not registered in California Post-harvest USE INSTRUCTIONS: This product may be applied after harvest of grain sorghum. Higher rates may be required tor control of large weeds which were growing in the crop at the time of harvest. Tank mix.tures with 2,4-D or dicamba may be used. This product may be applied to grain sorghum (milo) stubble following harvest to suppress or control regrowth. Apply 20 fluid ounces of this product per acre for control, or 15 fluid ounces of this product per acre for suppression. 21-Sep-1999 Page 25 of 66 Roundup D-Pak 99 revise.do(·

PRECAUTIONS. RESTRICTIONS: Do not harvest or feed treated vegetation for 8 weeks following application. 8.11 Grass Seed Production TYPES OF APPLICATIONS: Preplant, preemergence, renovation, site preparation. shielded sprayers. wiper applicators, spot treatments, creating rows in annual ryegrass USE INSTRUCTIONS: This proouct may be applied before, during, or after planting or renovation of turf or forage grass areJ.) grown for seed production. Applications MUST be made prior to the emergence of the crop to avoid crop injury. For maximum control of existing vegetation, delay planting to determine if any regrov..lh from escaped underground plant parts occurs. Where repeat treatments are necessary, sufficient regrowth must be attained prior to application. For warm-season grasses, such as bermudagrass, summer or fall applications pro'ide best control. PRECAUTIO""'S. RESTRICTIONS: Do not feed or graze treated areas for 8 weeks following application. Do not disturb soil or underground plam parts before treatment. Tillage or renovation techniques such as vertical mowing, coring or slicing should be delayed for 7 days after application to allow proper translocation into underground plant parts. Shielded sprayers USE INSTRUCTIONS Apply 22 fluid ounces to 2 quarts of this product as a broadcast spray in 10 to 20 gallons of water per acre to control weeds in the rows, Uniform planting in straight rows aid in shielded sprayer applications. Bc:st results are obtained when the grass seed crop is small enough to easily pass by or through the protective shields. PRECAUTIONS. RESTRICTIONS: Contact of this product in any manner to any vegetation to which treatment in not intended may cause damage. Such damage shall be the sole responsibility of the applicator. Wiper Applications PRECAUTIONS. RESTRICTIONS: Contact of the herbicide solution with desirable vegetation may result in damage or destruction Applicators should be adjusted so that the wiper contact point is at least 2 inches above the desirable vegetation. Weeds should be a minimum of 6 inches above the desirable vegetation. Better results may be obtained when more of the weed is exposed 10 the herbicide solution. \Veeds not contacted by the herbicide sO!Ulion "Oil! not be affected. This may occur in dense clumps, severe infeslations, or when height of weeds varies :>0 that not all weeds are contacted. In these instances, repeat treatments may be necessary. Better results may be obtained if 2 applications are made in opposite directions. Spot Treatments USE INSTRUCTIONS' Use a 213 to I percent solution. PRECAUTIC:-JS, RESTRICTIONS: Apply this product prior to heading of grasses Do not treat more than 10 percent of the total field to be harvested. The crop receiving the spray in the treated area will be killed. Take care to avoid drift or spray outside the target area for the same reason. Creating Rows in Annual Ryegrass USE INSTRUCTIONS: Use 10 to 20 fluid ounces of this product per acre mixed with water. Use the higher rate when the ryegrass is greater than 6 inches tall. Best results are obtained when applications are made before the ryegrass reaches 6 inches in height. 21-Sep-1999 Page 26 of 66 Roundup ~-Pak 99 revise.doc

PRECAUTIONS, RESTRICTIONS: Set nozzle heights to allow the establishment of the desired row spacing while preventing spray droplets, spray fines, or drift to contact the ryegrass plants not treated. Use of low pressure nozzles. or drop nozzles designed to target the application over a narrow band are recommended. G rower assumes all responsibility for crop losses from misapplication. 8.12 Herbs LABELED CROPS: Peppermint, spearmint USE INSTRUCTIONS: This product may be used as a spot treatment in spearmint and peppermint. Apply spray-ta-wet with hand-held equipment, such as backpack and knapsack sprayers, pump-up pressure sprayers, hand-guns, hand-wands or any other hand-held or motorized spray equipment used to direct the spray solution on to a limited area. PRECAUTIONS, RESTRICTIONS: Allow at least 7 days between application and harvest. Further applications may be made in the same area at 30 day intervals. No more than one-tenth of any acre should be treJted at one time. The crop receiving spray in the rreared area will be kiJJed. Take care ro avoid drift or spray outside the target area for this reason. 8,13 Pastures TYPES OF PASTURES: Bahiagrass, bermudagrass, bluegrass, brame, fescue, orchard grass, ryegrass, timothy, wheatgrass, alfalfa and clover TYPES OF APPLICATIONS: Spot treatment, wiper application, preplant, preemergence, pasture renovation Spot treatment and Wiper application USE INSTRUCTIONS: This product may be applied as a spot treatment or with wiper applicators in pastures. Applications may be made in the same area at 30-day intervals. PRECAUTIONS, RESTRICTIONS: For spot treatment and wiper applications, apply in areas where the movement of domestic livestock can be controlled. No more than one-tenth of any Defe should be treated al one lime. Remove domestic livestock before application and wait 14 days after application befnre grazing livestock or harvesting. Preplant, Precmergence and Pasture renovation USE INSTRUCTIONS: This product may be applied prior to planting or emergence of forage grasses and legumes. In addition, this product may be used to control perennial pasture species listed on this label prior to fe-planting. PRECAUTIONS, RESTRICTIONS: Remove domestic livestock before application and wait 8 weeks arrer application before grazing or harvesting. 8,14 Peanuts TYPES OF APPLICATIONS: Preplan!, preemergence, at-planting Page 27 of 66 Roundup D-Pak 99 revise.doc

USE INSTRUCTIONS: This product may be applied before, during or after planting peanuts. Applications must be made prior to the emergence of the crop. 8,15 Small Fruits and Berries LABELED CROPS: Blackberry, Blueberry, Boysenberry, Cranberry, Currant, Dewberry, Elderberry, Gooseberry, Huckleberry, Loganberry, Olallieberry, Raspberry (Black, Red), Youngberry TYPES OF APPLICATIONS: Preplant, preemergence, directed spray (except cranberry), wiper application USE INSTRUCTIONS: This product may be applied as a preplant or preemergence broadcast application or as a wiper application for crops listed in this section. Directed sprays may be applied to any crop except cranberries. Applications may be made to dry ditches in cranberry fields, but directed sprays around the base of the plants i~ not permitted. For wick or wiper applicators, mix 2)3 gallon of this proouct in 4 gallon:.- of water to prepare a 20 percent solution. In severe infestations, reduce equipment ground speed to ensure that adequate amounts of this producr are wiped on the weeds. A second treatment in the Opposile direction may be beneficial. PRECAUTIONS, RESTRICTIONS: Do not permit herbicide solution to contact desirable vegetation, including green shoots, canes or foliage. Allow a minimum of 30 days between last application and harvest of cranberries. For other small fruits and berries. allow a minimum of 14 days between last application and harvest. 8.16 Soybeans TYPES OF APPLICATIONS: Preplant, preemergence, at·planting, spot treatment, preharvest, selective equipment. For Roundup Ready soybeans, see the Roundup Ready Section of this label. Preplant, Preemergence and At-planting USE INSTRUCTIONS: This product may be applied before, during or after planting soybeans. Applications must be made prior to emergence of the crop. The following tank mixtures may be applied before. during or after planting in conventional tillage systems, into a cover crop, established sod or in previous crop residue. CANOPYTM LASSOIALACHLOR PROWL COMMANDTM LINEX PURSUIT'M DUAL LOROXILINURON PURSUIT PLUS DUAL II LOROXPLUS SCEPTERTM FRONTIER MICRO-TECH SENCORTMILEXONETM FUSIONTM PARTNER SQUADROl'TM GEMINFM PREVIEWTM TURBOTM For improved burndown, this product may be tank-mixed with 2,4-D or 2,4-DB. See the 2,4-D label for imervals between application and planting . . Annual weeds: For difficult-to-control weeds such as fall panicum, barnyardgrass, crabgrass, shattercane and broadleaf signal grass up to 2 inches tall, and Pennsylvania smartweed up to 6 inches tall, apply this product at 20 fluid ounces per aCre in these tank mixtures. For other labeled annual weeds, apply 10 to 15 tluid ounces 21-Sep-1999 Page 28 of 66 Roundup D-Pak 99 revise.doc

of this product per acre when weeds are less than 6 inches tall, and 20 to 30 fluid ounces when weeds are over 6 inches tall. PRECAUTIONS, RESTRICTIONS: The tanK mix recommendations in this section are not registered in California. Spot treatment USE INSTRUCTIONS: For spot treatments, apply this product prior to initial pod set in soybeans. PRECAUTIONS, RESTRICTIONS: Do not treat more than 10 percent of the roral field area to be harve"ed. The crop receiving spray in treated area will be killed. Take care to avoid drift or spray outside target area for the same rcason. Preharvest USE INSTRUCTIONS: This product provides weed control when applied prior to harvest of soybeans. Apply at rates given in the annual, perennial and woody brush tables. This product may be applied using either aerial or ground spray equipment. For ground applications, apply this producr in 10 to 20 gallons of water per acre. For aerial applications, apply this product in 3 to 10 gallons of water per acre. Apply after pods have ser and lost all green color. Allow a minimum of 7 days berween application and harvest of soybeans. Care should be taken to avoid excessive seed shatter loss due to ground application equipment. PRECAUTIONS. RESTRICTIONS: Do not graze or harvest treated crop for livestock feed within 25 days of last preharvest application. DO NOT APPLY MORE THAN 3.75 QUARTS PER ACRE OF THIS PRODUCT FOR PREHARVEST APPLICATIONS. DO NOT APPLY MORE THAN 20 FLUlD OUNCES PER ACRE OF THIS PRODUCT BY AIR. Do not apply to soybeans grown for seed as a reduction in germination or vigor may occur. Selective equipment USE INSTRUCTIONS: This product may be applied through recirculating ,prayers, shielded applicators, hocxled sprayers, wiper applir.:ators or sponge bars in soybeans. Allow at least 7 days between application and harvest. PRECAUTIONS, RESTRICTIONS: See the "SELECTIVE EQUlPMENT" pan of the "APPLICATION EQUlPMENT AND TECHNIQUES" section of this label for information on proper use and calibrarion of this equipment 8.17 Sugarcane TYPES OF APPLICATIONS: Preplant, preemergence, spot rreatment, fallow, hooded sprayers Preplant, Preemergence USE INSTRUCTIONS: This product may be applied in or around sugarcane fields or in fields prior to the emergence of plant cane. PRECAUTIONS. RESTRICTIONS: Do not apply to vegetation in or around ditches, canals or ponds containing water to be used for irrigation. 21-Sep-1999 Page 29 of 66 Roundup D-Pak 99 revise.doc

Spot treatment USE INSTRUCTIONS: This product may be applied as a spot treatment in sugarcane. For control of volunteer or diseased sugarcane, make a 213 percent solution of this product in water' and spray to wet the foliage of vegetation to be controlled. Volunteer Qf diseased sugarcane should have at least 7 new leaves. PRECAUTIONS, RESTRICTIONS: Avoid spray contact with healthy cane plants since severe damage or destruction may result. Do not feed Of graze treared sugarcane foliage following application. Fallow treatments USE INSTRUCTIONS This product may be used as a replacement for tillage in fJelds that are lying fallow between sugarcane crops. This product may also be used to remove the last stubble of ratcxm cane. For removal of la~I stubble of ratoon cane, apply 2.5 IO 3.2 quarts of this product in 10 to 40 gallons of wilter per acre {Q new growrh having at least 7 new leaves. Allow 7 or mOre days afcer application before tillage. Hooded sprayers USE INSTRUCTIONS: This product may be used through hooded sprayers for weed control between the rows of sugarcane. See the "APPLICATION EQUlPMENT AND TECHNIQUES" section of this label for guidance on the use of hooded sprayers, \'hen applying to sug::lfcane that is grown on raised beds, ensure that the h<XX1 is designed to completely enclose the spray. If necessary, extend the front and rear flaps of the hoods to reach the ground in furrows between the rows. PRECAUTIONS. RESTRICTIONS: Equipment must be designed, maintained and operated to prevent the herbicide solution from contacting the crop, Contact of this product in any manner to any vegetation to which treatment is not intended may cause damage. Do not allow treated weeds to come into contact with the crop. Droplets, mist, foam or splatter of the herbicide solution settling on the crop may result in discoloration, stunting or destruction. Such damage shall be the sole responsibility of the appJicaror. 8.18 Sunflowers TYPES OF APPLICA nONS: Preplant, preemergence USE INSTRUCTIONS' This product may be applied before, during or after planting sunflowers. Applications must be made prior to emergence ·of the crop. A tank mixture with Prow! may be applied before. during or after planting in conventional tillage systems. into a cover crop. established sod or in previous crop residue. PRECAUTIONS, RESTRICTIONS: Do nOl apply more than 20 fluid ounces of this product per acre for sunflowers. Make only one preplant or preemergent application per year. Do not feed or graze sunflower forage following application of this product. 8,19 Tree and Vine Crops (General) TYPES OF APPLICATIONS: General weed control, middles (between rows of trees), strips (in row of trees), perennial grass suppression, selective equipment (except kiwi), 21-Sep-1999 Page 30 of 66 Roundup D-Pak 99 revise. doc

NOTE: this section gives general directions that apply to all citrus crops, tree fruits, tree nuts and vine crops. See the individual crop sections for instructions, preharvest intervals, precautions and restrictions for specific crops. This product may be applied in middles. strips and for general weed control in established citrus groves. tree fruit and tree nut orchards, and vineyards. Apply at 10 fluid ounces to 3.2 quarts per acre. Repeat applications may be made up to a maximum of 6.7 quarts per acre per year. This proouct may also be used for site preparation prior to transplanting these crops. Allow a minimum of 3 days between application and transplanting. Applications may be made with boom equipment. COA. shielded sprayers, hand-held and high-volume wands, lances, orchard guns or with wiper applicator equipment, except as directed. Middles (between rows) USE INSTRLCTIONS: This product will control or suppress annual and perennial weeds and ground covers growing between the rows of labeled tree and vine crops. If weeds are under drought stress, irrigate prior to application. Reduced control may result if weeds have been mowed prior to application. A tank mixture of this product plus Goal 2XL may be used for annual weeds in middles between rows of citrus crops, tree fruirs, rree nuts and vine crops. This mixture is recommended when weeds are stressed or growing in dense populations. 10 to 20 fluid ounces per acre of this product plus 3 to 12 fluid ounces per acre of Goal 2XL wil! control annual weeds with a maximum height or diameter of 6 inches, including crabg.rass, hairy fleabane (Coll.rza bonariensis), common groundsel, junglerice, common lambsquarters, red root pigweed, London rocket, common ryegrass, shepherd's-purse, annual sowthistle, common cheeseweed (malvJ), maree (suppression), horseweedlmarestail (Conyza cQnadensis), stinging nettle and commo"n purslane (suppression). 8 to 20 fluid ounces per acre of this product plus 3 to 12 fluid ounces per are of Goal 2XL \'i1l control common cheeseweed (malva) with a maximum height or diameter of 3 inches. Strips (in rows) USE INSTRCCTIONS: This product may be applied in rows of tree or vine crop, and may also be tank mixed with the following products: OEYRINOL'" 50 OF DIREX'" 4L GOAL2XL KARMEX DF KROYARI KROVAR II PROWL PRINCEP CALIBER TM90 SIMAZlNE4L SIMAZlNE 80W SIM-TROL'M 4L; SOLICAMTM OF SURFLANTM AS SURFLAN75W Do not apply these tank mixtures in Puertt> Rico. Refer to the individual product labels for specific crops. rates, geographic restrictions and precautionary statements. Apply 10 tluid ounces to 3.2 quarts of this product per acre in these tank mixtures. Use rates at the higher end of the recommended rate range when weeds are stressed, growing in dense populations or are greater than 12 inches tall. Perennial grass suppression This product will suppress perennial grasses such as bahiagrass. bermudagrass. tall fescue. orchardgrass. Kentucky bluegrass, and quackgrass that are grown as ground covers in tree and vine crops. 21-Sep-1999 Page 31 of 66 Roundup D-Pak 99 revise.doc

For suppression of tall fescue. tine fescue. orchardgrass and quackgrass. apply 5 fluid ounces of this product in 10 rn 20 ga!!ons of water per acre. For suppression of Kentucky bluegrass covers, apply 4 fluid ounces of this product per acre. Do not add ammonium sulfate. For be.! results, mow cool season grass covers in the spring to even their height and apply this producl 3 to 4 days after mowing. For :.uppression of vegetative growth and seedhead inhibition of bahiagrass for approximately 45 days, apply 4t1uiJ ounces of this pr<xiuct in 10 to 25 gallons of water per acre. Apply 1 to 2 weeks after full green-up or aflt.'T mowing to J uniform height of 3 to 4 inches. This application must be made prior to ::.eedhc£Jd erne[·cncc For :,uppre:,sion up to 120 days, apply 2.5 fluid ounces of this product per acre, followed by an application of I to J fluid ounces per acre about 45 days later. Make no more than 2 applications per year. For burndown of bermudagrass. apply 20 to 40 fluid ounces of this product in 3 to 20 galions of water per acre. Use this treatment only if reduction of the bermudagrass stand can be tolerated. When burn down is reqlired prior to harvest, allow at least 21 days to ensure sufficient time for burndown to occur. For '·,uppression of bermudagrass. apply 4 to 10 fluid ounces of this proouct per acre east of the Rocky M()untain~ and 10 fluid ounces of this product per acre west of the Rocky Mountains. Apply in a total spray volume of 3 to 20 gallons per acre, no sooner than] to 2 weeks after full green-up. If the bermuda grass is mowed prior to application, maintain a minimum of3 inches in height. Sequential applications may be made when regrowth occurs and bermudagrass injury and stand reduction can be tolerated. East of the Rocky Mountains, rates of 4 to 6 fluid ounces per acre should be used in shaded conditions or where a ies.'>er degree of suppre-;sion is desired. SdectiH~ equipment (except kiwi) Shieldeu and wiper applicators may be used in tree crops and grapes. Refer to the individual crop ec!ions for time intavJI hetv.'een application and harvest. PREC\UTIO:--lS. RESTRICTIONS: For citron and olives. apply as a post-directed spray only. Avoid painting cut stUll1PS \vith this product as injury resulting from root grafting may occur in adjacent trees. EXTRHIE CARE MUST BE EXERCISED TO AVOID CONTACT OF HERBICIDE SOLUTION. SPRAY. DRIFf OR MIST WITH FOLIAGE OR GREEN BARK OF TRUNK, BRANCHES. SUCKERS. FRUIT OR OTHER PARTS OF TREES AND VINES. CONTACT OF THIS PRODUCT WITH OTHER THAN MATURED BROWN BARK CAN RESULT IN SERIOUS CROP DAMAGE. S.20 Tree Fruits LABELED CROPS: Apple. Apricot. Cherry (Sweet. Sour). Crabapple. Loquat. Mayhaw, Nectarine. Olive. Peach. Pear. Plum/Prune (All). Quince TYPES OF APPLICATIONS: General weed control, middles (between rows of trees), strips (in row of trees). selective equipment 21-Sep-1999 Page 32 of 66 Roundup D-pak 99 revis.doc

NOTE: For general use directions, see the "TREE, NUT AND VINE (GENERAL)" section. The following directions are specific to tree fruits. Restrictions on application equipment For cherries, any application equipment listed in this section may be used in all states. Any application equipment listed in this section may be used in apricots, nectarines, peaches and plums/prunes growing in Arizona, California, Colorado, Idaho, Kansas, Kentucky, New Jersey, North Dakota, Oklahoma, Oregon, Texas, Utah and Washington. except for peaches grown in the states specified in the following paragraph. In all other states use wiper equipment only. For PEACHES grown in Alabama, Arkansas, Florida. Georgia, Louisiana, Mississippi, North Carolina, South CHolina and Tennes$ee only, apply with a shielded boom sprayer or shielded wiper applicator, which prcvenL,> any contact of this product with the foliage or bark of trees. Apply no later than 90 day,',. after first bloom. Applic;.\tions made after this time may result in severe damage. Remove suckers and Jow-hanging limbs at least 10 days prior to application. Avoid applications near trees with recent pruning wounds or other mech"nic"1 injury. Apply only near trees which have been planted in the orchard for 2 or more years. EXTREME CARE MUST BE TAKEN TO ENSURE NO PART OF THE PEACH TREE IS CONTACTED. PRECAUTIONS, RESTRlCTIONS: Allow a minimum of I day between last application and harvest for apple, crabapple, loquat, may haw, pear, quince. Allow <.J minimum of J 7 days between last application and harvest for apricot, cherry. nectarine, olive, peach, plum/prune. 8.21 Tree Nuts LABELED CROPS: Almond, Beechnut, Brazil nut, Butternut, Cashew, Chestnut, Chinquapin, Filbert (Hazelnut), Hickory nut, Macadamia, Pecan, Pistachio, Walnut (Black, English) TYPES OF APPLICATIONS: General weed control, middles (between rows of trees), strips (in row of trees), selective equipment NOTE: For general use directions, see the "TREE, NUT AND VINE (GENERAL)" section. The following directions are specific to tree nuts. PRECAUTIONS, RESTRICTIONS: Allow a minimum of 3 days between last application and harvest of tree nuts. 8.22 Tropical Crops LABELED CROPS: Atemoya, Avocado, Banana, Barbados Cherry (acerola), Breadfruit, Canistel, Carambola. Cherimoya. Cocoa beans, Coconuts, Coffee, Dates, Durian, Figs, Guava, Jaboticaba, Jackfruit, Longan, Lychee, Mango, Mangosteen, Marmaladebox (genip), Papaya, Passion fruit, Persimmon, Pineapple, Plantain. Pomegranate, Rambutan, Sapodilia, Sapote (black. marney, white), Soursop, Sugar apple, Tamarind. Tea . . USE INSTRUCTIONS: This product may be applied for general weed control or for site preparation prior to transplanting crops listed in this section. In coffee and banana, delay applications 3 months after transplanting to allow the new coffee or banana plant to become established. 21-Sep-1999 Page 33 of 66 Roundup D-Pak 99 revise.doc

PRECAlJIlONS. RESTRICTIONS: Allow a minimum of I day between last application and harvest of banana, gUJva, papaya and plantain. Allow a minimum of 14 days between last applicarion and harvest of acerola, atemoya. avocado. breadfruit, canistel, carambola, cherimoya. cocoa beans, coconuts, dates, figs, genip. jaboticaba. jackfruit. longan. Iychee. mango. mayhaw. passion fruit. persimmon. pomegranate. sapodilla.,apote. soursop. sugar apple. tamarind. and tea. Allow a minimum of 28 days between last application and harvest of coffee. Do not feed or graze treated pineapple forage following application. 8.23 Vegetable Crops LABELED CROPS: Amaranth. Arrugula. Artichoke (Jerusalem). Beans (All). Beet greens. Garden beets. Broccoli (.\11). Brussels sprouts. Cabbage (All), Cabbage (Chinese). Cantaloupe. Cardoon. Cavalo Broccolo. Carrot. CO·Jlitlower. Casaba melon. Celery. Celery (Chinese). Celeriac. Celtuce. Chard (Swiss). Chayote. Chervil. Chick peas. Chicory. Chrysanthemum. Collards. Corn salad. Crenshaw melon. Cress. Cucumber. Dandelion. Dock (sorrel), Eggplant, Endive. Fennel (florence), Garlic, Gherkin. Ginseng. Gourds, Ground cherry. Guar. Honeydew melon. Honey ball melon. Horseradish. Kale. Kohlrabi. Leek. Lentils. LeUuce. Mango melon, Melons (All), Mizuna, Muskmelon. Mustard greens. Okra, Onion, Oriental radish, Parsley. Parsnips, Peas (All). Pepinos. Pepper (All). Persian melon. Potato (Irish). Pumpkin, Purslane, Radish, Rape greens, Rhubarb, Rutabaga, Salsify, Shallot, Spinach (All), Mustard Spinach, Squash (Summer. Winter), Sugar beets. Sweet potato, TomatiJlo. Tomato, Turnip, Watercress, Watermelon, Yams. USE INSTRUCTIONS: This product may be applied prior to the emergence of direct seeded vegetables or prior to transplanting vegetables. except that for the following crops, apply only prior to planting. Allow at least 3 dJ~s between application and plan ring of cantaloupe, casaba melon, crenshaw melon, cucumber, eggplant, hcrkjn, gourds, ground cherry. honeydew melon. honey ball melon, mango melon. melons (all), muskmelon. pepper (all), persian melon, pumpkin, squash (summer, winter), tamatillo, watercress, and watermelof. PRECAUTIONS, RESTRICTIONS: When applying this product prior to transplanting crops into plastic mulch, care must be taken to remove residues of this product, which could cause crop injury, from the plastic prior to rransplanting. Residues can be removed by a single 0.5 inch application of water, either by narural rainfall or -ia <.J sprinkler system, Applicarions made at emergence will result in injury or dearh ro emerged seedlings. Wipe:r applicators may be used in rutabagas, Allow at least 14 days between application and harvest. 8.24 Vine Crops LABELED CROPS: Grapes (raisin, table. wine). Kiwi fruit TYPES OF APPLICATIONS: General weed control. middles (between rows), strips (in row). selective equipment NOTE: For general use directions. see the 'TREE. NUT AND VINE (GENERAL)" section. The following directions are specific to vine crops. Applications should not be made when green shoots, canes or foliage are in the spray lone. 21-Sep-:'399 Page 34 of 66 Roundp D-Pak 99 revise.doc

In the northeast and Great Lakes regions, applications must be made prior to the end of bloom stage of grapes to avoid injury, or make applications with shielded sprayers or wiper equipment. PRECAUTIONS. RESTRICTIONS: Allow a minimum of 14 days between last application and harves!. 9.0 Roundup Ready® Crops The following instructions include all applications which can be made onto Roundup Ready® crops during the complete cropping season. DO NOT combine these instructions with other recommendations made for crop varieties which do not contain the Roundup Ready gene, in the CROPS (ALPHABETICAL) Section 8 of this label. MONSANTO COMPANY RECOMMENDS USE OF THIS PRODUCT FOR POSTEMERGENCE APPLICATION ONLY ON CROP VARIETIES DESIGNATED AS CONTAINING THE ROUNDUP READY® GENE. Applying this product to crop varieties which are not designated as Roundup Ready will result in severe crop injury and yield loss. Avoid contact with foliage, green stems, or fruit of crops, or any desirabJe plants which do not contain the Roundup Ready gene, since severe injury or destruction wHj result. The Roundup Ready designation indicates that the crop variety contains a patented gene which provides tolerance to Monsanto's Roundup brand herbicides. Information on Roundup Ready crop varieties may be obtained from your seed supplier or Monsanto representative. SPRA Y DRIFT MANAGEMENT A VOID DRIFT. EXTREME CARE MUST BE USED WHEN APPLYING TillS PRODUCT TO PREVENT INJURY TO DESIRABLE PLANTS AND CROPS. For proper stewardship of aerial applications over-the-top of Roundup Ready crops, Monsanto recommends th()t growers ()nd applicators read and follow all precautions and procedures contained in the use guide "A Guide to On-Target Aerial Application" available by calling I-SOD-ROUNDUP (1-800-768-6387) or on the internet at www.FARMSOURCETM.com. See the MIXING and APPLlCA nON EQUIPMENT AND TECHNIQUES sections of this label for additional directions and restrictions on the application of this product. DO NOT exceed a maximum rate of 20 fluid ounces per acre of this product when making applicatjons by air unless otherwise directed. For aerial application in California or Arkansas, refer to the Federal supplemental label for aerial applications in those state~ for specific instruccions, res(ric(ions and requirements. Tank mixtres with other herbicides, insecticides, or fungicides may result in reduced weed control or crop injury and are NOT recommended for over-the-top applications of this product. Sprayer Preparation: It is important that sprayer, lines, filters, and mixing equipment be clean and free of pesticide residue before making applications of this product to Roundup Ready crops. Follow the cleaning procedures specified on the label of the product(s) previously used. Many crops can be very sensitive to herbicides at extremely low concentrations and care should be taken to thoroughly clean all equipment prior to use. NOTE: The following recommendations are based on a clean start at planting by using a burn down application or tillage to control existing weeds before crop emergence. In notil1 and stale seedbed systems, a 21-Sep-1999 Page 35 of 66 Roundup D-Pak ~9 revise.doc

) preplant burn-down treatment of 15 to 40 fluid ounces per acre of this product is recommended to control existing weeds prior to crop emergence. There are no rotational crop restrictions following the application of this product. 9.1 Canol a with the Roundup Ready Gene TYPES OF APPLICATIONS: Preplant, preemergence, postemergence USE INSTRUCTIONS lJxirnum Allowable Combined Application Quantities Per Season PrepJant (lnd preemergence applications Total in-crop app!icJtion from emergence to 6 leaf 40 fluid ounces per acre 20 fluid ounces per acre For "round applications with broadcast equipment, apply this product in 5 to 20 gallons of spray solution per acre. Carefully select proper nOlzle and spray pressure to avoid spraying a fine £!list. For best results v.ith ground application equipment use flat fan nozzles. Check for even distribution of spray droplets. For aerial applications apply this. product in 3 to 15 gallons of water per acre. Preplat or Preemergent applications; This product may be applied by aerial or ground application equipment prior to planting or emergence of canola. Over-the-top applications: This product may be applied by aerial or ground application equipment postemergence to Roundup Ready canola from emergence through the six leaf stage of development. To maximize yield potentia! spray canDIa early to eliminate competing weeds. Any single over-the-top broadcast 3pplication should not exceed 10 fluid ounces per acre. No more than two over-the-top broadcast appJi("ations may be made from crop emergence through the six leaf stage of development. Sequential over-the-top applic;lIions of this product musr be at least JO days apart \Veeds controlled. for specific rates of application and instructions for control of various annual and perennial weeds. refer (() [he annual and perennial weed rate tables in this booklet. Some weeds with mu!!iple germination times or suppressed (stunted) weeds may require sequential applications of this product for control. The second application should be made after some regrowth has occurred and at leas! I () days after a previous application of this product. This product will control or suppress, most perennial weeds. For some perennial weeds, repeat applications may be required to eliminate crop competition throughout the growing season. PRECAUTIONS, RESTRICTIONS: See section 9.0 for general precautionary instructions for use in Roundup Ready crops. Allow a minimum of 60 days between last application and canola harvest. DO NOT use this product on canDia with the roundup ready gene planted in the following states: Alabama, Delaware. Florida, Georgia, Kentucky, Maryland, New Jersey, North Carolina, South Carolina, Tennessee, Virginia and West Virginia. 9.2 Corn with the Roundup Ready Gene 21-Sep-1999 Page 36 of 66 Roundup D-Pak 99 revisE.doc

TYPES OF APPLICATIONS: Preplant, preemergence, at-planting, postemergence, spot treatment. preharvesl, post-harvest USE INSTRUCTIONS: When applied as directed. this product controls labeled annual grass and broad leaf weeds in Roundup Ready corn. Many perennial grasses and broad leaf weeds will be controlled or suppressed with one or more application of this product. Applications should be made to actively growing weeds before they reach the maximum size listed in the annual and perennial weed rate tables. Refer to the "MIXING" section for proper use instructions. This product may be applied postemergence to Roundup Ready corn from emergence through the VB stage (8 leaves with collars) Or until corn height reaches 30 inches, whichever comes first. Single in-crop applications of this product are not to exceed 20 fluid ounces per acre. Sequential in-crop applications of this product from emergence through the V8 stage or 30 inches must not exceed 40 fluid ounces per acre per growing season. Maximum Allowable Application Rates I. Combined total per year for all applications 5 quarts per acre 2. PrepJant, Preemergence applications 3.2 quarts per acre 3. Total in-crop applications from emergence through 40 fluid ounces per acre the V8 stage or 30 inches 4. Maximum preharvest application rate after maximum kernal 20 fluid ounces per acre fill is complete and the crop is physiologically mature (black layer formation) until 7 days before harvest The addition of I to 2 percent dry ammonium sulfate by weight or 8.5 to 17 pounds per 100 gallons of water may increase the performance of this product under hard water conditions, drought conditions or when tank mixed with BulJetl!', Micro-Tech:: or Partner Z Herbicides. Ensure that ammonium sulfate is completely dissolved in the spray tank before adding herbicides. Thoroughly rinse the spray system with clean water after use to reduce corrosion. The addition of other additives. including fertilizers and micronutrients are not recommended with this product since this may result in increased potential for crop injury. For ground applications: Use the recommended rates of this product in 5 to 20 gallons of spray solution per acre as a broadcast spray. Carefully select correct nozzles and spray pressure to avoid spraying a fine mist. Check for even distribution of spray droplets. For aerial applications: Use the recommended rates of this product in 3 to 15 gallons of spray solution per acre. PRECAUTIONS, RESTRICTIONS: See section 9.0 for general precautionary instructions for use in Roundup Ready crops. Allow a minimum of 50 days between application of this product and harvest of COrn forage and 7 days between application and harvest of corn grain. Allow a minimum of 10 days between in-crop applicatiuns of this product. Weeds Control Recommendations Apply 15 to 20 fluid ounces of Roundup D-PAK herbicide per acre for control of labeled grasses and broad leaf weeds in conventional and no-till corn production systems. Refer to the "ANNUAL WEED RATE TABLE" for rate recommendations for specific annual weeds. Roundup D-PAK herbicide applied at up to 20 fluid ounces per acre will control or suppress the growth of perennial weeds such as: bermudagrass, Canada thistle, common milkweed, field bindweed, hemp dogbane, horsenettle, nutsedge. quackgrass, rhizome 21-Sep-1999 Page 37 of 66 Roundup D-Pak 99 revise.doc 11, )'I!

johnsongrass, redvine, trumpetcreeper, swamp smart weed. and wirestem muhly. For additional information on perennial weeds, see the "PERENNIAL WEED RATE TABLE". Preemergence followed by Postemergence Weed Control Program This product may be applied postemergence in-crop following any labeled preemergence herbicide application. The post application of this product should be made before the weeds reach a height andior density that the weeds become competitive with the crop. A single in-crop application of this product at the recommended rate will provide control of emerged weeds listed on the label. This product may be applied postemergence to Roundup Ready corn from emergence through the V8 stage (8 leaves with collars) or until corn height reaches 30 inches (free standing), whichever comes first. Postemergence Only Weed Control Program This product may be applied alone as a postemergence in-crop application to provide control of emerged weeds listed on the label. The postemergence application of this product should be made before the weeds ret1ch.a heigh! and/or density thai rhe weeds become competitive with the crop.]f new flushes of weeds occur, a sequential application of this product at 15 to 20 fluid ounces per acre will control the labeled grasses and broad leaf weeds. This product may be applied postemergence to Roundup Ready corn from emergence through the V8 stage or until corn height reaches 30 inches (free standing), whichever comes first. This product may be applied in tank mixture with a labeled rate of Harness®, Harness® Xtra, Harness® Xtra S.6L, Micro-Tech"', Bullet", Panner", Permit~ or Atrazine. Refer to the specific product label and observe all precautions and limitations on the label for all products used in tank mixtures. including application timing restrictions. soil restrictions, minimum recropping interval and rotational guidelines - the more restrictive requirements apply. Maximum Height Of Corn Tank Mix Partner For Application Harness II inches Harness Xtra Harness Xtra 5.6 Bullet' 5 inches Micro-Tech* Partner* Permit 24 inches Atrazine 12 inches *Bullef, Micro-Tech and Partner are not registered for use as a postemergence application in Texas. 9.3 Cotton with the Roundup Ready Ge!,e TYPES OF APPLICA nONS: Preplant, preemergence, at-planting, over-the-top, post-directed, hooded sprayer, pre harvest ATTENTION: Monsanto recommends this product for use only over-the-top of or directed onto improved cotton varieties that are designated as cotton with the Roundup Ready" gene, SEVERE INJURY OR DEATH OF COTTON WILL RESULT IF ANY COTTON VARIETIES NOT PROPERLY DESIGNATED AS HA VING THE ROUNDUP READy" GENE ARE SPRA YED WITH THIS PRODUCT_ ROUNDUP READY® COTTON VARIETIES MUST BE PURCHASED FROM AN AUlliORIZED LICENSED SEED SUPPLIER. lliE DESIGNA nON, "ROUNDUP READY", INDICATES lliE COTTON V ARIETY CONTAINS A PATENTED PROPRIETARY TRAIT. 21-Sep-1999 Page 38 of 66 Roundup D-Pak 99 revis€.doc

USE INSTRUCTIONS: Maximum Allowable Yearly Rates

1. Combined total per year for all applications 5 quarts pencre
2. Preplant, Preemergence applications 3.2 quarts per acre
3. Toral in-crop applications from cracking to layby 2.5 quarts per acre
4. Maximum preharvest application rate 1.25 quarts per acre For ground applications with broadcast equipment, apply this product in 5 to 20 gallons of spray solution per acre. Carefully select proper nozzle and spray pressure 10 avoid spraying a fine mist. For best results with ground application equipment, use flat fan nozzles. Check for even distribution of spray droplets. For aerial nppiications, apply this product in 3 to 15 gallons of water per acre. PRECAUTIONS, RESTRICTIONS: See section 9.0 for general precautionary instructions for use in Roundup Ready crops. The combined total application from crop emergence until harvest must not exceed 3.75 quarts per acre. Over-the-lop applications: This product may be applied by aerial or ground application equipment postemergence to Roundup Ready cotton from the ground cracking stage until the four leaf (node) stage of development (until the fifth true leaf reaches the size of a quarter). Over-the-lOp applications made after the four leaf (nodeJ stage of development may result in boll loss, delayed maturity and/or yield loss. Any single over-the-top broadcast application should not exceed 20 fluid ounces per acre. No more than two over-the-top broadcast applications may be made from crop emergence through the four leaf (node) stage of development. Sequential over-the-top applications of this product must be at least 10 days apart and cotton must have at least two nodes of incrementa! growth between applications. Post-directed or hooded applications. This product may be applied using precision pOSl-directed or hooded sprayers to Roundup Ready cotton through layby. At this stage, posr-directed equipment should be used which directs the spray to the base of the cotton plants. Contact of the spray with cotton leaves should be avoided to the maximum extent possible. To minimize spray onto the leaves of the coHon plants. place nozzles in a low position directing a horizonwl spray pattern under the coUon leaves ro contact weeds in the row, and maintain low spray pressure (less than 30 PSI). For best results. make applications while weeds are small (less than 3 inches). Any single post-directed application should not exceed 20 fluid ounces per acre of this product. No more than two applications should be made from the fifth leaf through Jayby. Sequential in­ crop applications of this product must be at least 10 days apan and cotton must have at least two nodes of incremental growth between applications. AITENTION: USE OF ROUNDUP D-PAK IN ACCORDANCE WITH LABEL DlRECTIONS IS EXPECTED TO RESULT IN NORMAL-GROWTH OF ROUNDUP READY COITON, HOWEVER, VARIOUS ENVIRONMENTAL CONDITIONS, AGRONOMIC PRACTICES AND OTHER FACTORS MAKE IT IMPOSSIBLE TO ELIMINATE ALL RISKS ASSOCIATED WITH THIS PRODUCT, EVEN WHEN APPLICATIONS ARE MADE IN CONFORMANCE WITH THE LABELSPECIFJCATIONS. IN SOME CASES, THESE FACTORS CAN RESULT IN BOLL LOSS, DELAYED MATURITY AND/OR YIELD LOSS. Salvage Treatment. This treatment may be used after the four leaf stage of development and should only be used where weeds threaten to cause the loss of the crop. 20 fluid ounces per acre may be applied either as an over-the~top applications or as a post-directed treatments sprayed higher on the cotton plants and over the weeds. NOTE: SALVAGE TREATMENTS WILL RESULT IN SIGNIFICANT BOLL LOSS, VELA YED MATURITY AND/OR YIELD LOSS, NO MORE THAN ONE SAL V AGE TREA TMENT SHOULD BE USED PER GROWING SEASON. 21-Sep-1999 Page 39 of 66 Roundup D-Pak 99 revise.doc

Weeds controlled. For specific rates of application and instructions for control of specific weed species, refer to the annual and perennial weed rate tables in this booklet. Roundup D-PAK applied at 20 fluid ounces per acre will burndown or suppress the growth of the following perennial weeds and reduce crop competition: yellow and purple nutsedge, rhizome johnsongrass, common bennudagrass, silverleaf nightshade, trumpet creeper, and redvine. Fall preharvest applications may be' required for control of these 'perennial weeds. Some weeds with multiple germination times or suppressed (stunted) weeds may require sequential applications of this product for control. Preharvest applications. This product may be applied for pre harvest annual and perennial weed control as a broadcast treatment to Roundup Ready cotton after 20% boll crack. Allow a minimum of 7 days between application and harvest. NOTE: Roundup D-PAK will not enhance the performance of harvest aids when applied to Roundup Ready cotton. DO NOT apply Roundup D-PAK pre harvest to crops grown for seed. 9.4 Soybeans with the Roundup Ready Gene TYPES OF APPLICATIONS: Preplant, preemergence, at-planting, postemergence, pre harvest, post-harvest USE INSTRUCTIONS: When applied as directed, this product will control labeled annual grasses and broadleaf weeds in Roundup Ready soybeans. Many perennial grasses and broad leaf weeds will be controlled Or suppressed with one or more applications of this product. Maximum Allowable Application Rates I. Combined total per year for all applications 5 quarts per acre 2. Preplant, Preemergence applications 3.2 quarts per acre 3. Total in-crop applications from cracking throughout flowering 2 quarts per acre 4. Maximum preharvest application rate 20 fluid ounces per acre PRECAUTIONSIRESTRICTIONS: See section 9.0 for general precautionary instructions for use in Roundup Ready crops. The combined total application from crop emergence through harvest must not exceed 2 quarts per acre. The maximum rate for any single in crop application is 40 fluid ounces per acre. The maximum combined total of this product \.'hich can be applied during flowering is 40 fluid ounces per acre. Allow a minimum of 14 days between tinal application and harvest or feeding of soybean grain, forage or hay. ANNUAL WEED RATE TABLES The following rate recommendations will provide control of labeled grasses and broadleaf weeds in conventional and no-till Roundup Ready soybean production systems. Refer to the "ANNUAL WEED RATE TABLE" in this label for rate recommendations for specific annual weeds. Monsanto will not warrant crop safety or weed control when Roundup Ready soybeans are treated with herbicides not specified on this supplemental label. Because of the potential for: I) crop injury, 2) poor weed control from antagonism, and/or 3) rotational crop restrictions, herbicides not specified on this supplemental label should not be used, whether applied preemergence or applied postemergence as a tank mixture with Roundup D-PAK herbicide. This product may be used up to 40 fluid ounces per acre in any single in-crop application for control of annual weeds, where heavy weed densities exist. MIDWESTI MID-ATLANTIC RECOMMENDATIONS 21-Sep-1999 Page 40 of 66 Roundup D-Pak 99 revise.doc

Narrow row or drilled soybeans: A single in-crop application of this product will provide effective control of labeled weeds. For best results, an initial application of 20 fluid ounces per acre, on 4 - 8" weeds is recommended. Weeds will generally be 4 - 8" tall 3 to 5 weeks after planting. If the initial application is delayed and weeds are 8 - 18" tall, use 30 fluid ounces per acre for best results. Under adverse growing conditions such as drought, hail, wind damage or a poor soybean stand that slows or delays canopy closure, a sequential application of this product at J5 to 20 fluid ounces per acre may be necessary to control late flushes of weeds. Wide row soybeans: An in-crop appl ication of this product will provide effective control of the initial stand of labeled v.eeds. For best results, an initial application of 20 fluid ounces per acre, on 4 - 8" weeds is recommended. Weeds will generally be 4 - 8" tall 3 to 5 weeks after planting. If new flushes of weeds occur. they can be controlled by sequential applications of this product. Initial and Sequential (if needed) Applications Weed Height (inches I 1-3 4-8 8-18 Rate (fl oz/A) 15 20 3D Giant ragweed: Apply 20 fluid ounces per acre when the weed is 8 -12" tall to avoid the need for sequential application. Black nightshade. Pennsylvania smartweed, ladysthumb smart weed, velvetleaf and waterhemp : Apply 20 fluid ounces per acre to weeds 3 - 6" tall and 30 fluid ounces per acre when weeds are up to 12 inches tall. For Morningglory species apply 20 fluid ounces per acre when weeds are up to 4 inches tall, and 30 tluid ounces per acre when weeds are up to 6 inches tall. Some weeds, such as black nightshade. woolly cupgrass. shattercane, wild proso millet, burcumber, and gianr ragweed. wirh mulciple germinacion rimes may require a sequencial applicarion of chis product. Suppressed or stunted weeds may also require sequential applications. Sequential applications should be made after some regrowth has occurred. Use a minimum of IS fluid ounces of this product per acre for sequenrial applicarions. SOUTHEAST RECOMMENDATIONS Narrow row, drilled, or wide-row soybeans: An in-crop application of this product will provide effective control of the initial stand of labeled weeds. For best results, an initial application of20 fluid ounces per acre, on 3 - 6" weeds is recommended. WeedS'will generally be 3 - 6" tall 2 to 3 weeks after planting. Initial Treatment Weed Height (inches) 3-6 6-12 Rate (fl oz/A) 20 30 Under adverse growing conditions such as drought, hail, wind damage or a poor soybean stand that slows or delays canopy closure, a sequential application of this product at 10 to 20 fluid ounces per acre may be necessary to control late flushes of weeds. 21-Sep-1999 Page 41 of 66 Roundup D-Pak 99 revise.doc 'fl~ ?'{

Sequential Application (if needed) Weed Height (inches) 2-3 3-6 6-12 Rate (fl ozl A) 10 15 20 Florida pusley, hemp sesbania and spurred anoda: Apply 20 fluid ounces per acre to weeds 2 - 4"lor the initial application. Apply 20 fluid ounces per acre when these weeds are 3 - 6" tall if a sequential application is necessary. Morningglory, black nightshade, groundcherry. and Pennsylvania smart weed: Apply 15 fl ounces per acre on I - 3" weeds, 20 fluid ounces per acre on 3 - 6" weeds, or 30 fluid ounces per acre on 6 - 12" weeds for the initial application. Some weeds, such as black nightshade. broadleaf signal grass, Texas panicum, burcumber, and sicklepod, with multiple germination times may require a sequential application of this product. Suppressed or stunted weeds may also require sequential applications. Sequential applications should be made after some regroVith has occurred. Use a minimum of 10 fluid ounces of this product per acre for sequential applications. DELT AlMID-SOUTH RECOMMENDATIONS Narrow row, drilled, or wide row soybeans: An in-crop application of this product will provide effective control of the initial stand of labeled weeds. A sequential application will be required to control new Ilushes of weeds. For best results. an initial application of 20 fluid ounces per acre. on 2 - 4" weeds is recommended. Weeds will generally be 2 - 4" tall 2 to 3 weeks after planting. Initial Treatment Weed Height (inches) 2-4 5-12 Rate (tl oz/A) 20 30 Sequential Application Weed Height Rate (inches) (tl oz/A) 2-3 10 3-6 15 6-12 20 Hemp sesbania and spurred anoda: Apply a sequential treatment of 20 tl ounces per acre on 3 - 6"weeds if necessary Some weeds, such as black nightshade. broadleaf signalgrass. Texas panicum. burcumber. and sicklepod. with multiple germination times may require a sequential applicatjon of this product. Suppressed or stunted weeds may also require sequential applications. Sequential applicalions should be made after some regrowth has occurred. Use a minimum of to fluid ounces of this product per acre for sequential applications. PERENNIAL WEEDS RATE RECOMMENDATIONS A 20 to 40 fluid ounces per acre rate (Single or multiple applications) of this product will control or suppress perennial weeds such as: bermudagrass, Canada thistle, common milkweed, field bindweed, hemp dogbane. horsenellie. marestail (horseweed). nutsedge. quack grass, rhizome jOhnsongrass, redvine, trumpelcreeper, swamp smartweed, and wirestem muhly. 21-Sep-1999 Page 42 of 66 Roundup D-Pak 99 revise.doc

For best results, allow perennial weed species to achieve at least 6" of growth before spraying with Roundup D-PAK herbicide. 9.5 Sugar beets with the Roundup Ready Gene TYPES OF APPLICATIONS: Preplant. preemergence. postemergence USE INSTRUCTIONS: This product may be applied postemergent over the top of Roundup Ready sugar beets from emergence to 30 days prior [Q harvest. To maximize yield potential spray sugar beets early to eliminate competing weeds. Up to.:1. sequential over-the-top applications of this product may be made, and they should be at least 10 days apart. Maximum Allowable Application Rates

1. Combined total per year for all applications 5 quarts per acre
2. Preplant, Preemergence applications 3.2 quarts per acre
3. Emergence to 8 leaf stage 1.5 quarts per acre
4. Between 8 leaf stage and canopy closure 20 fluid ounces per acre For ground applications with broadcast equipment. apply this product in 5 to 40 gallons of spray solution per acre. Carefully select proper nozzle and spray pressure (0 avoid spraying a fine mist. For best results with ground application equipment use nat fan nozzles. Check for even distribution of spray droplets. For aerial application: Use the recommended rmes of this product in 3 to 15 gallons of spray solution per acre. PRECAUTIONS. RESTRICTIONS: See section 9.0 for general precautionary instructions for use in Roundup Ready crops. The combined total application from crop emergence through harvest must not exceed 2.8 quarts per acre. The maximum rate for any single application between emergence [0 the 8 leaf stage is 1 quarts per acre. The maximum rate for any single application between the 8 leaf stage and canopy closure is 20 fluid ounces per acre. Allow a minimum of 30 days between last application and sugar beet harvest. For any crop NOT listed in the ··CROPS·· section of this label booklet. applications must be at least 30 days prior to planting. \Veeds controlled. For rates of application and instructions for control of specific weed species, refer to the annual and perennial weed tables in this label booklet. Ammonium sulfate may be mixed with this product for applications to Roundup Ready sugar beets. Refer to the "Mixing" section for use instructions t:or ammonium sulfate. Some weeds with multiple germination times or suppressed (stunted) weeds may require a second application of this product for complete control. The second application should be made after some regrowth has occurred and at least 10 days after a previous application of this product. This product will control or suppress, most perennial weeds. For some perennial weeds, repeat applications may be required to eliminate crop competition throughout the growing season. 10.0 Farmsteads 21-Sep-1999 Page 43 of 66 Roundup D-Pak 99 revise.doc

TYPES OF APPLlCA nONS: General nonselective weed control, trim-and-edge, greenhouse / shadehouse, chemical mowing. cut slUmps, habitat management. 10.1 General nonselective weed control, Trim-and-edge, Greenhouse!Shadehouse . USE INSTRUCTIONS: This product may be used to control annual weeds, perennial weeds and woody brush which are found in any part of the farmstead, including building foundations, along and in fences, in dry ditches and canals, along ditch banks, farm roads, shelterbelts, prior to landscape plantings and equipment srorage areas. This product may be tank mixed with the following products. Refer to these product labels for approved farmstead sites and application rates. For annual weeds, use 20 fluid ounces per acre of this product when weeds are less than 6 inches tall and 30 tluid ounces per acre when weeds are greater than 6 inches tall. For perennial weeds, apply 40 fluid ounces to 3.2 quarts per acre in these tank mixes. For lank mixtures with these products through backpack sprayers. handguns or other high-volume spray-to-wet applications, see the "HAND-HELD AND HIGH VOLUME EQUIPMENT' section of this label for recommended rates. Arsenal Plateau Banvel Princep DF Barricade 65WG Princep Liquid Diuron Ronstar 50 WP Endurance Sahara Escort Simazine Karmex DF Surflan Krovar I DF Telar Oust Vanquish Pendulum 3.3 EC 2,4-D Pendulum WDG Banvel tank mixtures may not be applied by air in California. Greenhouse/Shadehouse This produci may be used to control weeds in and around greenhouses and shadehouses. Desirable vegetation must not be present during application and air circulation fans must be turned off. 10.2 Chemical mowing USE INSTRUCTIONS: This product will suppress perennial grasses listed in this section to serve as a substitute for mowing. Apply this product at a rate of 3.75 to 5 fluid ounces per acre. Use 5 fluid ounces of this product per acre when treating tall fescue, fine fescue. orchardgrass or Quackgrass covers. Use 3.75 fluid ounces of this product per acre when treating Kentucky bluegrass. Apply treatments in 10 to 20 gallons of spray solurion per acre. Chemical mowing applications may be made along farm ditches and other parts of farmsteads. PRECAUTIONS, RESTRICTIONS: Use only in areas where some temporary injury or discoloration of perennial grasses can be tolerated. 10.3 Cut Stumps 21-Sep-1999 Page 44 of 66 Roundup D-Pak 99 revise.doc

TYPES OF APPLICA TION: Treating cut slUmps in any noncrop site listed on this label USE INSTRUCTIONS: This product will control regrowth of cut stumps and resprouts of many types of woody brush and tree species, some of which are listed below. Apply this product using suitable equipment to ensure coverage of the entire cambium. Cut trees or resprouts close to the soil surface. Apply a 50 to 100 percent solution of this product to the freshly-cut surface immediately after CUlling. Delays in application may result in reduced performance. For best results, applications should be made during periods of active growth and full leaf expansion Alder Eucalyptus Madrone Oak Reed, giant Salt-cedar Sweetgum Tan oak Willow PRECAl'T10NS, RESTRlCTIONS: DO NOT make cut stump applications when the roots of desirable woody brush or (rees may be grafted to the roots of the cut stump. injury resulting from root grafting may occur in adjacent woody brush or trees. lOA Habitat Management TYPES OF USES: Habitat restoration and maintenance, wildlife food plots Habitat restoration and maintenance USE INSTRUCTIONS: This product may be used to control exotic and other undesirable vegetation in habitat management areas. Applications can be made to allow recovery of native plant species, prior to planting desirable native species, and for similar broadspectrum vegetation control requirements in habitat management areas. Spot treatments can be made to selectively remove unwanted plants for habitat maintenance and enhancement. The tank mixtures listed in this section of the Jabel may be used for habitat res[orarion and mainrenance. Wildlife food plots USE INSTRUCTIONS: This product may be used as a sire preparation treatment to control annual and perennial weeds prior to planting wildlit<: food plots. Any wildlife f,m species may be planted after applying this producr, or native species may be allowed to repopUlate the area. If tillage is needed to prepare a seedbed, wait 7 days after application before tillage. 11.0 AN:-iUAL WEEDS RATE TABLE ALPHABETICALLY BY SPECIES Water carrier volumes of 3 to 10 gallons per acre for ground applications and 3 to 5 gallons per acre for aerial applications are recommended. Apply to actively growing annual weeds. Do not tank mix with soil residual herbicides when using these rates unless otherwise specified. For weeds that have been mowed, grazed or cut, allow regrowth to occur prior to treatment 21-Sep-1999 Page 45 of 66 Roundup D-Pak 99 revise.doc

For those rates less than 30 fluid ounces per acre. this product may be used up to 30 fluid ounces per acre where heavy weed densities exist. ANNUAL WEEDS RATE TABLE RATE WEED (FLUID OUNCES PER ACRE) SPECIES 10 15 20 25 30 MAXIMUM HEIGHTILENGTH Annoda. spurred 2" 3" 5" 8" Barley 18" 18"+ Barnyardgrass 3" 6" 7" 9" Bassia. fivehook 6" Bittercress 12" 20" Bluegrass, annual JO" Bluegrass, bulbous 6" Brame, downy U 6" 12"- Bmme, Japanese 6" 12" 24" Browntop panicum 6" 8" 12" 24" Buckwheat, wild.1 I" 2" Burcucumber 6" 12" 18" Buttercup 12" 20" Carolina foxtail 10" Carolina geranium 4" 9" Carpet weed 6" 12" Cheal 2 6" 20" Chervil 20" Chickweed 12" 18" Cocklebur 12" 18" 24" 36" Copperleaf. hophornbeam 2" 4" 6" 21-Sep-1999 Page 46 of 66 Roundup D-Pak 99 revise.doc

7 , 7, Copperleaf, Virginia 2" 4" 6" Corn 6" 12" 20" Corn speedwell 12" Crabgrass 6" 12" 18" Cutleaf evening primrose 3" 6" Devilsclaw (unicorn plant) 3" 6" Dwarf dandelion 12" Eastern mann"lgras 8" 12" Eelipta 4" 8" 12" Fall panicum 4" 6" 8" 12" 24" Falsedandelion 20" Falseflax, small seed 12" Fiddleneek 6" 12" Field pennyeress 6" 12" Filaree 6" 12" Fleabane. annual 6" 20" Fleabane, hairy 6" 10" (Conyza bonariensis) Fleabane, rough 3" 6" 12" Florida pusley 4" 6" Foxtail 6" 12" 20" Goatgrass, joinzed 6" 12" Goosegrass 3" 5" 8" 18" Grain sorghum (milo) 6" 12" 20" Groundsel, common 6" 10"- Hemp sesbania 2" 4" 6" 8" Henbit 6" 12" Horseweedl 6" 12" IS" 21-Sep-1999 Page 47 of 66 Roundup D- Pak 99 revise.doc

'f~ b 1~ Marestail (Coflyza canadensis) Itchgrass 6" 12" 18" Jimsonweed 12" 18" Johnsongrass. 12" 18" 24" seedling Jungierice 3" 6" T 9" Knotweed 3" 8" 12" 20" , Kochia - 3 t06" 12" Lambsquaner~ 6" S" 12" 20" LillIe barley 12" London rocker 6" 24" Mayweed 2" 6" 12" 18" Morningg\ory. annual (Ipomoea spp.) 2" 3" 4" 6" Mustard. blue 6" 12" IS" Mustard. tans~ 6" 12" 18" Mustard. tumble 6" 12" lW' Mustard. wild 6" 12" 18" Nightshade. black 4" 8" Nightshade, hairy 4" 8" Oats 6" 20" Pigweed species 12" 18" 24" Prickly lelluce 6" 12" Purslane 6" 8" 12" Ragweed, common 6" 12" IS" Ragweed. giant 4" 9" 18" Red rice 4" Russian thistle 6" 12" 21-Sep-1999 Page 48 of 66 Roundup D- Pak 99 re'vJ.se.doc

~~ hit Rye, cereal 2 6" 18" 18"+ Ryegrass 6" 12" Sand bur, field 6" 12" Shattercane 12" 18" Shepherd's-purse 6" 12" Sicklepod 2" 4" 8" Signal grass, broadleaf 3" 6" 7" 9" Smartweed, ladysthumb 6" 9" ) Smartweed, Pennsylvania 6" 9" Sowthistle, annual 6" 12" Spanishneedles 8" 18" Speedwell, purslane 12" Sprangletop 6" 12" 20" Spurge, prostrate 6" 12" Spurge, spotted 6" 12" Spurry, umbrella 6" Stinkgrass 12" Sunflower 12" 18" Teaweedl Prickly sidw. 2" 4" 6" Texas panicum 6" 8" 12" 24" Velvetleaf 3" 6" 12" Virginia pepperweed 18 Waterhemp 3" 6" 12" Wheat 2 6" 12" IS" Wheat, 6" 12" 18+" (overwi ntered) Wild oats 6" 20" 21-Sep-19S) Page 49 of 66 Roundup D-Pak 99 revise.doc

Wild Proso Millet 6" 12" 18" Witchgrass 12" Woolly cupgrass 6" 12" Yellow rocket 12" 20" 1 For control of Downy Brame in no-till systems. use 15 fluid ounces per acre, 1 Performance is better if application is made before this weed reaches the boot stage of growth. 3 Use 15 fluid ounces per acre of this product to control wild buckwheat in the cotyledon to 2-leaf stage. Use 20 fluid ounce:::. per acre to control 2 to 4-Jeaf wild buckwheat. For improved control of wild buckwheat over 2 im:he~ in size. use sequential Irealments of 20 fluid ounces followed by 20 fluid ounces of this product per acre, ~ Do not [rea! kochia in the bU[lDn stage. 11.1 Annual Weeds--Waler Carrier Volumes of 10 10 40 Gallons per Acre Apply 20 to 30 fluid ounces of this product per acre. Use 20 fluid ounces per acre if weeds are less than 6 inches tall and 30 fluid ounces per acre if weeds are over 6 inches tall. These rates will provide control of weeds listed in the annual weed control tables when water carrier volumes are 10 to 40 gallons per acre for ground applications. 11.2 Annual Weeds -- Tank Mixtures wilh 2,4-D or Banvel 8 to 10 tluid ounces of this product plus 0.25 pound a.i. of Ban vel or 0.5 pound a.i. of 2,4-D per acre will control the follO\ .... ing weeds with the maximum height or length indicated: 6" -- prickly lettuce, marestaillhorseweed (Collyza calladellsis), morningglory (Ipomoea spp.J, kochia (Banvel only); 12"-­ cocklebur, lambsquarters. pigweed, Russian thistle. 10 fluid ounces of this product plus 0.5 pound a.i. of 2,4-D per acre will control the following weeds when they are a maximum height or length of 6 inches: common ragweed. giant ragweed, Pennsylvania srnartweed. and velvetleaf. 8 fluid ounces of this product plus 0.25 pound a.i. of Banvel or 0.5 pound a.i. of 2,4-D per acre will control foxtail up to 18". Refer to the specific product labels for crop rotation restrictions and cautionary statements of all products used in tank mixtures. Some crop injury may occur if Banvel is applied within 45 days of planting. DO NOT apply Banvel tank mixtures by air in California. 12.0 PERENNIAL WEEDS RATE TABLE ALPHABETICALLY BY SPECIES 'Apply to actively growing perennial weeds. 21-Sep-1999 Page 50 of 66 Roundup D-Pak 99 revise.doc ~o i l'ci

NOTE: If weeds have been mowed or tilled. do nO! treat until plants have resumed active growth and have reached the recommended stages. Repea! treatments may be necessary to control weeds regenerating from underground parts or seed. Repeat treatments must be made prior to crop emergence. ' Unless otherwise stated. allow 7 or more days after application before tillage. Best results are obtained when soil moisture is adequate for active weed growth. Weed Species Rate Water Hand-Held (QT/A) Volume (GPA) % Solution Alfalb 2/3- I 114 3-10 I 1140/, AlJigmorweed 2.5 3-20 1% Anise (fennel) I-I 1/4% Bahiagra:;~ 2-3.2 3-20 I 1/4% Benrgrass 10-20 I 1/4% Bermudagrass 2-3.2 3-20 I 1/4% Bermudagrass, water (knotgrass) 2/3- I 5-10 I 1/4% Comments Make applications after the last hay cutting in the fall. Allow alfalfa to regrow to a height of 6 to 8 inches or more prior to treatment. Applications should be followed with deep tillage at least 7 days after treatment. but before soil freeze-up. Partial contra!. Apply when most of the plants are in bloom. Repeat applications will be required to maintain comrol. Apply as a spray-to-wet treatment. Optimum results are obtained when plants are treated at the bud to full-bloom stage of growth. Apply when most plants have reached the early head stage. For suppression in grass seed production areas. For ground applications only. Ensure entire crown area has resumed growth prior to a fall application. Bentgrass should have at least 3 inches of growth. Tillage prior to treatment should be avoided. Tillage 7 to 10 days after application is recommended for best results. For control, apply 3.2 quarts of this product per acre. For partial control. apply 2 quarts per acre. Treat when bermudagrass is actively growing and seedheads are present. Retreatment may be necessary to maintain control. Apply I quarts of this product in 5 to JO gallons of water per acre. Apply when water bermudagrass is 12 to 18 inches in length. 21-Sep-:999 Page 51 of 66 Roundup D-Pak 99 revise.doc

Bind"eed, field 0.5-3.2 3-20 21-Sep-1999 I 1/4% Allow 7 or more days before tilling, flushing or flooding the field. Fall applications only: Apply 20 fluid ounces of this product in 5 to 10' gallons of water per acre. Fallow fields should be tilled prior to application. Apply prior to frost on water bermudagrass that is 12 to 18 inches in length. This product is not registered in California for use on water bermuda grass. Do not treat when weeds are under drought stress as good soil moisture is necessary for active growth. For control, apply 2.5 to 3.2 quarts of this product per acre west of the Mississippi River and 2 to 2.5 quarts east of the Mississippi River. Apply when the weeds are at or beyond full bloom. For best results, apply in late summer or fall. Fall treatments must be applied before a killing frost. Also for control, apply I 1/4 quarts of this product plus 0.5 pound a.i. of Banvel in 10 to 20 gallons of water per acre. Do not apply by air. For suppression on irrigated agricultural land, apply 213 to I 1/4 quarts of this product plus I pound a.i. of 2,4-D in IOta 20 gallons of water per acre with ground equipment only. Applications should be made following harvest or in fall fallow ground when the bindweed is activefy growing and the majority of runners are 12 inches or more in length. The use of at least one irrigation will promote active bindweed growth. For suppression, apply 10 fluid ounces of this product plus 0.5 pound a.i. of 2,4-D in 3 to 10 gallons of water per acre for ground applications and 3 to 5 gallons of water per acre for aerial applications. Apply by air in fallow and reduced tillage systems only. Applications should be delayed until maximum emergence has occurred and when vines are between 6 to 18 inches in length. In California only, apply 213 to 3.2 quarts of this product per acre. Actual rate needed for suppression or control will vary within this Page 52 of 66 Roundup D-Pak 99 revise.doc

Bluegrass, Kentucky 213-1 114 Blueweed, Texas 2-3.2 Brackenfern Bromegrass, smooth Bursage, woolly-leaf Canary grass, 21-Sep-1999 2-2.5 213-1 1/4 3-40 3-40 3-40 3-40 3-20 1114% I 114% 213-1% I 114% I 114% range depending on local conditions. For suppression on irrigated land where annual tillage is performed. apply 20 fluid ounces of this product in 3 to 10 gallons of water per acre. Apply to bindweed·that has reached a length of 12 inches or greater. Allow maximum weed emergence and runner growth. Allow 3 or more days affer applicarion before £illage. Apply I 114 quarts of this product in 10 to 40 gallons of water per acre when most plants have reached boot-to-early seed head stage of development. For paniJI control in pasture or hay crop renovation, apply 2/3 to I quarts of this product in 3 to 10 gallons of water per acre. Apply to actively growing plants when most have reached 4 to 12 inches in height. Apply 2.5 to 3.2 quarts of this product per acre west of the Mississippi River and 2 to 2.5 quarts per acre east of the Mississippi River. Apply when plants are at or beyond fulr bloom. New leaf development indicates active growth. For best results, apply in late summer or fall. Fall treatments must be applied before a killing frost. Apply to fully expanded fronds which are at least 18 inches long. Apply I 114 quarts of this product in 10 to 40 gallons of water per acre when most plants have reached boot-ta-early seedhead stage of development. For partial control in pasture or hay crop renovation, apply 2/3 to I quarts of this product in 3 to 10 gallons of water per acre. Apply to actively growing plants when most have reached 4 [0 12 inches in height. For control, apply I 114 quarts of this product plus I pint of Banvel per acre. For partial control. apply. 20 fluid ounces of this product plus I pint of Banvel per acre. Apply when plants are producing new active growth which has been initiated by moisture for at least 2 weeks and when plants are at or beyond flowering. Page 53 of 66 Roundup D-Pak 99 revise,aoc

$'/ ~ 1~ reed I 1/4-2 3-40 I 1/4% For best results, apply when most plants have reached the boot-to-head stage of growth. Cattail 2-3.2 3-40 I 1/4% Apply when most plants have reached the early head stage. Clover; red, white2-3.2 3-20 I 1/4% Apply when most plants have reached the early bud stage. Cogongrass 2-3.2 10-40 I 1/4% Apply when cagangrass is at least 18 inches tall in lale summer or faJl. Due to uneven stages of growth and {he dense nature of vegetation preventing good spray coverage, repeat trea[mems may be necessary to maimain control. Dailisgrass 2-3.2 3-20 I 114% Apply when most plants have reached the early head stage. Dandelion 2-3.2 3-40 I 114% Apply when most plants have reached the early bud stage of growth. Also for control, apply 10 fluid ounces of this product plus 0.5 pound a.i. 2,4-D in 3 to 10 gallons of water per acre. Dock, 2-3.2 3-40 I 114% Apply when most plants have reached the early bud curly stage of growth. Abo for control, apply 10 fluid ounces of this product plus 0.5 pound a.i. 2,4-D in 3 to 10 gallons of water per acre. Dogbane, hemp 2.5 3-40 I 1/4% Apply when most plants have reached the late bud 10 flower stage of growth. Following crop harvest or mowing, aJlow weeds to regrow to a mature stage prior to !realmen!. For best results, apply in late summer or fall. For suppression, apply 10 fluid ounces of this product plus 0.5 pound a.i. of 2,4-D in 3 to 10 gallons of water per acre for ground applications and 3 to 5 gallons of warer per Jcre for aerial applications. Delay applications until maximum emergence of dogbane has occurred. Fescue 2-3.2 3-20 I 1/4% Apply when most plants have reached the early head (except tall) stage. Fescue, tall 2/3-2 3-40 I 1/4% Apply 2 quarts of this product per acre when most plants have reached boot-la-early seedhead stage of development. 21- Sep-19 9 9 Page 54 of 66 Roundup D-Pak 99 revise.doc

Guineagrass Horsenettle Horseradish leeplant Jerusalem artichoke Johnsongrass 21-Sep-1999 2 3-40 3-20 2,5 3-40 2-3,2 3-20 0.5-2 3-40 2/39, I 11490 I 1/490 I-I 114% I 11490 21390 ·Fall applications only: Apply 20 fluid ounces of this product in 3 to 10 gallons of water per acre. Apply to fescue in the fall when plants have 6to 12 inches of new growth. A sequential application of 10 fluid ounces per acre of this product will improve long-term control and control seedlings germinating after fall treatments or the following spring. Apply when most plants have reached at least the 7-leaf stage of growth. Ensure thorough coverage when using hand-held equipment. Apply when most plants have reached the early bud stage. Apply when most plants have reached the lale bud to flower stage of growth. For best results, apply in late summer or fall. Ieeplant should be at or beyond the early bud stage of growth. Thorough coverage is necessary for best control. Apply when most plants are in the early bud stage. In annual cropping systems apply 213 to I 114 quans of this product per acre. Apply 20 fluid ounces of this produci in 3 to 10 gallons of water per acre. Use 1 1/4 quarts of this product when applying JO to 40 gallons of water per acre. In noncrap. or areas where annual tillage (no-till) is not practiced, apply I 114 to 2 quans of this product in IOta 40 gallons of water per acre. For best results, apply when most plants have reached the boot-to-head stage of growth or in the fall prior to frost. Allow 7 or more days after application before tillage. Do not tank mix with residual herbicides when using the 20 tluid ounces per acre rate. For burndown of Johnsongrass, apply 10 fluid ounces of this product in 3 to 10 gallons of water per acre before the plants reach a height of 12 inches. For this use, allow at least 3 days .after treatment before tillage. Spot treatment (panial control or suppression)-­ Apply a 213 percent solution of this product when Johnsongrass is 12 to 18 inches in Page 55 of 66 Roundup D-Pak 99 revise.doc

b ll height. Coverage should be uniform and complete. Kikuyugrass I 1/4-2 3-40 I 1/4% Spray when most kikuyugrass is at least 8 inches in height (3 or 4-leaf stage of growth). Allow 3 or more days after application before tillage. Knapweed 2.5 3-40 I 1/4% Apply when most plants have reached the late bud to flower stage of growth. For best results, apply in late summer or fall. LantCtna 2/3-1 % Apply at or beyond the bloom stage of growth. Use the higher application rate for plants that have reached the woody stage of growth. Lespedeza 2-3.2 3-20 I 1/4% Apply when most plants have reached the early bud stage. Milkweed, common 2 3-40 I 1/4% Apply when most plants have reached the late bud to flower stage of growth. Muhly. wirestem 2/3-1 1/4 3-40 I 1/4% Use 20 fluid ounces of this product in 3 to 10 gallons of water per acre. Use I 1/4 gums of this product when applying 10 to 40 gallons of w3!er per acre or in pasrure, sod, or noncrop areas. Spray when the wirestem muhly is 8 inches or more in height. Do not till between harvest and fall applications or in the fall or spring prior to spring applications. Allow 3 or more days after application before tillage. :\1ullein. common2-3.2 3-20 I 1/4% Apply when most plants are in the early bud stage. Napiergrass 2-3.2 3-20 I 1/4% Apply when most plants are in the early head stage. Nightshade, silverleaf I 114 3-10 . I 1/4% Applications should be made when at least 60 percent of the plants have berries. Fall treatments must be applied before a killing frost. Nutsedge; purple, yellow 0.5-2 3-40 2/3-1 1/4% Apply 2 quarts of this product per acre or apply a 2/3 to I 1/4 percent solution for control of nutsedge plants and immature nutlets attached to treated plants. Treat when plants are in flower or when new nutlets can be found at rhizome tips. Nutlets which have not germinated will not be controlled and may germinate following treatment. Repeat 21-Sep-1999 P&ge 56 of 66 Roundup D-Pak 99 revise.doc

Orchardgrass 213-1 114 3-40 Pampas grass Paragrass 2-3.2 3-20 Phragmites 2-3.2 10-40 21-Sep-1999 I 114% • I-I 1/4% I lid'" 213-1 1/4% treatments will be required for long-tenn control of ungenninated tubers. Sequential applications: 213 to I 114 quarts of this product in 3 to 10 gallons of water per acre will also provide control. Make applications when a majority of the plants are in the 3 to 5~ leaf stage (Jess than 6 inches tall). Repeat this application, as necessary, when newly emerging plants reach the 3 to 5-leaf stage. Subsequem applications will be necessary for long-term control. For partial control of existing plants, apply 10 to 40 tluid ounces of this product in 3 to 40 gallons of water per acre. Treat when plants have 3 to 5 leaves and most are less than 6 inches tall. Repeat treatments will be required to control subsequent emerging plants or regrowth of existing plants. Apply I 1/4 quarts of this product in 10 to 40 gallons of water per acre when most plants have reached boot-tn-early seedhead stage of development. For partial control in pasture or hay crop renovation, apply 2/3 to I quarts of this product in 3 to 10 gallons of water per acre. Apply to actively growing plants when most have reached 4 to 12 inches in height. Orchardgrass sods going \0 no-till corn: Apply 2/3 to I quarts of this product in 3 to 10 gallons of water per acre, Apply to orchardgrass that is a minimum of 12 inches tall for spring applications and 6 inches tall for fall applications. Allow at least 3 days following application before planting. A sequential application of atrazine will be necessary for optimum results. Pompasgrass should be at or beyond the boot stage of growth. Thorough coverage is necessary for best contror. Apply when most plants are in the early head stage. For panial control. For best results. treat during late summer or fall months or when plants are actively growing and in full bloom. Treatment before or after this stage may lead to reduced control. Due to the dense nature of the vegetarian, which may prevent good spray coverage or uneven stages of growth, repeat Page 57 of 66 Roundup D-Pak 99 revise. doc

~lt treatments may be necessary to maintain control. Visual control symptoms will be slow to develop. Poison hemlock -- 2/3-1 114% Apply as a spray-to-wet treatment. Optimum results are obtained when plants are treated at the bud to full-bloom stage of growth. Pokeweed, common 2/3 3-40 I 114% Apply to actively growing plants up to 24 inches tall. Quackgrass 2/3-2 3-40 I 114% In annual cropping systems, or in pastures and 'ods followed by deep tillage: Apply 20 fluid Ounces of this product in 3 to 10 gallons of Water per acre. For 10 to 40 gallons of water per acre, apply I 114 quarts of this product. Do not tank mix with residual herbicides when using the 20 fluid ounce rate. Spray when quackgrass is 6 to' 8 inches in height. Do not till between harvest and fall applications or in fall or spring prior to spring application. Allow 3 or more days after application before tillage. In pastures or sods, use a moldboard plow for best results. In pastures, sods or noncrop areas where deep tillage does not follow application: Apply I 114 to 2 quarts of this product in 10 to 40 gallons of Water per acre when the quackgrass is greater than 8 inches tall. Redvine 0.75-1 1/4 5-10 I 1/4% For suppression, apply 15 fluid ounces of this product per acre at each of two applications 7 to 14 days apart or a single application of I 114 quarts per acre. Apply recommended rates in 5 to 10 gallons of water per acre. Apply in late September or early October to plants which are at least 18 inches tall and have been growing 45 to 60 days since the last tillage operation. Make applications at least I week before a killing frost. Reed, giant 1 1/40/, Best results are obtained when applications are made in late summer to fall. Ryegrass, perennial 2/3-2 3-40 2/3% In annual cropping systems apply 2/3 to I 114 quarts of this product per acre. Apply 2/3 quart of this product in 3 to 10 gallons of water per acre. Use I 114 quarts of this product when applying 10 to 40 gallons of water per acre. In noncrop, or areas where annual tillage (no-till) 21-Sep-1999 Page 58 of 66 Roundup D-Pak 99 revise GvC

Smartweed, swamp SowthisrJe, perennial Spurge, leafy Starthistle, yellow Sweet potato, wild Thistle, artichoke 2-3.2 I 112-2 I 114 Thistle, Canada I 114-2 21-Sep-1999 3-40 3-40 3-10 10-40 3-40 I 1/4% I 1/4% I 114% 1 114% I 114% I 114% I 1/4% is not practiced, apply I 114 to 2 quarts of this product in 10 to 40 gallons of water per acre. For best results, apply when most plants have reached the boot-to-head stage of growth or in the fall prior to frost. Do not tank-mix with residual herbicides when using the 213 quart per acre ratc. Apply when most plants have reached the early bud stage of growth. Also for control, apply 10 fluid ounces of this product plus 0.5 pound a.i. of 2,4-0 in 3 to 10 gallons of water per acre in the late summer or fall. Apply when most plants are at or beyond the bud stage of growth. After harvest, mowing or tillage in the late summer or fall, allow at least 4 weeks for initiation of active growth and rosette development prior to the application of this product. Fall treatments must be applied before a killing frost. Allow 3 or more days after application before tillage. For suppression, apply 10 fluid ounces of this product plus 0.5 pound aj. 2,4-0 in 3 to 10 gallons of water per acre in the late summer or fall. If mowing has occurred prior to treatment, apply when most of the plants are 12 inches tall. Best results are obtained when applications afe made during the rosette, bolting and early flower stages. Partial control. Apply to plants that are at or beyond the bloom stage of growth. Repeat applications may be required. Partial control. Apply to plants that are at or beyond the bloom stage of growth. Repeat applications may be required. Apply when most plants are at or beyond the bud stage of growth. After harvest, mowing or tillage in the late summer or fall, allow at least 4 weeks for initiation of active growth and rosette development prior to the application of this product. Fall treatments must be applied Page 59 of 66 Roundup D-Pak 99 revise. doc

Timothy I 1/4-2 3-40 I 114% Torpedograss 2.5-3.2 3-40 I 1/4% Trumpetereeper I 1/4 5-10 I 1/4% Vaseygrass 2-3.2 3-20 1 1/4% Velvetgras:> 2-3.2 3-20 1 1/4% Wheargra,s, western I 1/4-2 3-40 1 1/4% 13.0 WOODY BRUSH AND TREES RA TE TABLE ALPHABETICALL Y BY SPECIES before a killing frost. Allow 3 or more days 'after application before tillage. For suppression. apply 2/3 quan of this product. or 10 fluid ounc!!s of this product plus 0.5 pound a.i. 2,4-D. in 3 to 10 gallons of water per acre in the lare summer or fall afrer harvest. mowing or tillage. AJlow rosette regrowrh ro a minimum of 6 inches in diameter before £feating. Applications can be made as long as leaves are still green and plants are actively growing at the time of application. Allow 3 or more days after application before tillage. for best resuirs, apply when most plants have reached the b()OHO~head stage of growth. For partial control. Apply when most plants are at or beyond the seedhead stage of growth. Repeat applications will be required to maintain control. Fall treatments must be applied before frost. Partial control. Apply in late September or October. to plants which are at least 18 inches tall and have been growing 45 to 60 days since the last tillage operation. Make applications at least I week before a killing frost. Apply when most plants are in the early head stage. Apply when most plants are in the early head stage. For best results. apply when most plants have reached the bOOl-lo-head stage of growth. Apply this product after full leaf expansion. unless otherwise directed. Use the higher rate for larger plants andlor dense areas of growth. On vines. use the higher rate for plants that have reached the woody stage of growth. Best results are obtained when application is made in late summer or fall after fruit formation. In arid areas. best results are obtained when applications are made in the spring to early summer when brush species are at high moisture content and are flowering . . Ensure thorough coverage when using hand-held equipment. Symptoms may not appear prior to frost or senescence with fall treatments. Page 60 of 66 Roundup D-Pak 99 revise.doc

Allow 7 or more days after application before tillage, mowing or removal. Repeat treatments may be necessary to control plants regenerating from underground parts or seed. Some autumn colors on undesirable deciduous species are acceptable provided no major leaf drop has occurred. Reduced performance may result if fall treatments are made following a frost. Weed Species Rate Water Hand·Held (QT/A) Volume (CPA) % Solution Alder 2·2.5 Ash 1/4·3.2 Aspen, quaking I 1/4·2 Bearmar (Bearclover) Beech Birch Blackberry Blackgum Bracken Broom: French, Scotch Buckwheat, California Cascara Catsclaw Ceanothus 1/4-3.2 1/4-3.2 I 1/3 2-2.5 I 1/4-3.2 I 1/4-3.2 I 1/4-3.2 I 1/4-3.2 3-40 2/3·1 % 3·40 2/3·1 1/4% 3·40 2/3-1 % 3-40 2/3-1 1/4% 3-40 2/3-1 1/4% 3-40 2/3% 10-40 2/3-1 % 3-40 2/3-1 1/4% 3-40 2/3-1 1/4% 1-1 1/4% 2/3-1 1/4% 3-40 2/3-1 1/4% 2/3-1 % 3-40 2/3-1 1/4% Comments For control Panial control For control Partial control Partial control For control For control. Make applications after plants have reached full leaf maturity. Best results are obtained when applications are made in late summer or fall. Applications may also be made after leaf drop and until a killing frost or as long as stems are green. After berries have set or dropped in late fall, blackberry can be controlled by applying a 1/2 percent solution of this product. For control of blackberries after leaf drop and until killing frost or as long as stems are green. apply 2 to 2.5 quarts of this product in 10 to 40 gallons of water per acre. For control For control For control For partial control. Thorough coverage of foliage is necessary for best results. Partial control Partial control Partial control 21-Sep-1999 Page 61 of 66 Roundup u-Pak 99 revise.doc

t.").~ 78 Chamise 2/3% For control. Thorough coverage of foliage is necessary for best results. Cherry; bitter. black. pin I 114-2 3-40 213-1% For control Coyote brush I-I 114% For control. Apply when at least 50 percent of the new leaves are fully developed. Dogwood I 1/4-3.2 3-40 2/3-11/4% Pania\ control Elderberry I 114 3-40 213% For control Elm I 114-3.2 3-40 2/3-11/4% Partial control Eucalyptus I 114% For control of eucalyptus resprouts. apply when resprouts are 6 to 12 feet tall. Ensure complete coverage. A void application to drought-stressed plants. Florida holly I 1/4-3.2 3-40 213-1 114% Partial control (Brazilian Peppertree) Gorse I 114-3.2 3-40 213-1 114% Partia! control Hasardia 213-1 114% Partial control. Thorough coverage of foliage is necessary for best results. Hawthorn 114-2 3-40 213-1% For control Hazel I 114 3-40 2/3% For control Hickory I 1/4-3.2 3-40 2/3-1 1/4% Partial control Honeysuckle 2-2.5 3-40 2/3-1 % For control Hornbeam, I 114-3.2 3-40 2/3-1 1/4% Partial control American Kudzu 2.5 3-40 1 1/4% For control. Repeat applications may be required to maintain control. Locust. black I 114-2.5 3-40 213-1 1/4% Partial control Madrone I 114% Partial cOntrol. Apply tf) resprouts that are 3 to 6 feet resprouts tall. Best results are obtained with spring/early summer treatments. Manzanita I 1/4-3.2 3-40 2/3-1 114% Partial control Maple. red I 114-2.5 3-40 213-1% For control. apply a 213 to I percent solution when at least 50 percent of the new leaves are 21-Sep-1999 Page 62 of 66 Roundup D-Pak 99 revise.doc

(.1 b It fully developed. For partial control, apply I 113 to 2.5 quarts of this product per acre. Maple, sugar 213-1% For control. Apply when at least 50 percent of the new leaves are fully developed. Monkey tlower 213-1 14% Partial control. Thorough coverage of foliage is necessary for best results. Oak; black, white I 114-2.5 3-40 213-1 114% Partial control Oak, post 2-2.5 3-40 213-1 % For control Oak: northern, 213-1% For control. Apply when at least 50 percent of Ihe new pin lea\les are fulJy developed Oak; southern I 1/4-2 3-40 213-1 % For control red Persimmon I 114-3.2 3-40 213-1 114% Partial control Pine I 114-3.2 3-40 213-1 114% For control Poison ivy! Poison oak 2.5-3.2 3-40 I 114% For control. Repeat applications may be required to maintain control. Fall treatments must be applied before leaves lose green color. Poplar, yellow 114-3.2 3-40 213-1 ',,% Partial control Redbud, 114-3.2 3-40 213-1 1/4% For control eastern Rose, multiflora I 114 3-40 1/3% For control. Treatments Should be made prior [0 leaf deterioration by leaf-eating insects. Russ-iLln olive I 114-3.2 3-40 213-1 114% Panial control Sage, black 2/3% For control. Thorough coverage of foliage is necessary for best results. Sage, white I 114-3.2 3-40 213-11/4% Panial control Sage brush, 213% For control. rhorough coverage of foliage is necessary California for best results. Salmonberry I 114 3-40 213% For control Salt-cedar I 114-3.2 3-40 2/3-1 114% For control Sassafras I 114-3.2 3-40 213-1 1/4% P,:mial control 21-Sep-1999 Page 63 of 66 Roundup D-Pak 99 revise.doc

Sourwood 1 114-3.2 3-40 213-1 114% Partial control Sumac: poison, 1 114-2.5 3-40 213-1 114% Partial control smooth, winged Sweetgum 1 114-2 3-40 2/3-1 % For control Swordfern 1 114-3.2 3-40 213-1 1/4% Partial control Tallowtree, 213% For control. Thorough coverage of foliage is necessary Chinese for besr results. Tan oak resprouts-- I 114% For partial control. Apply lO resprouts that are less than 3 to 6 feef lall. Best results are obtained with fall applications. Thimbleberry 1 114 3-40 213% For control Tobacco, tree 2/3-1 1/4% Partial control Trumpercreeper I 114-2 3-40 213-1 % For control Vine maple 1 114-3.2 3-40 213-1 114% Partial control Virginia creeper I 114-3.2 3-40 213-1 1/4% For control Waxmyrtle, 1 114-3.2 3-40 213-\ \14% Partial control southern Willow 2 3-40 2/3% For control 14.0 LIMIT OF WARRANTY AND LIABILITY This Company warrants that this product conforms to the chemical description on the label and is reasonably tit for the purposes set forth in the Complete Directions for Use label booklet ("Directions") when used in accordance with those Directions under tH'e conditions described therein. NO OTHER EXPRESS WARRANTY OR IMPLIED WARRANTY OF FITNESS FOR PARTICULAR PURPOSE OR MERCHANTABILITY IS MADE. This warranty is also subject to the conditions and limitations stated herein. Buyer and all users shall promptly notify this Company of any claims whether based in contract, negligence, strict liability, other tort or otherwise. Buyer and all users are responsible for all loss or damage from use or handling which results from conditions beyond the control of this Company, including, but not limited to, incompatibility with products other than those set forth in the Directions, application to or contact with desirable vegetation, unusual weather, weather conditions which are outside the range considered normal at the application site and for the time period when the product is applied, as well as weather conditions which are outside the application ranges set forth in the 21-Sep-1999 Page 64 of 66 Roundup D-Pak 99 revise.doc

Directions, application in any manner not explicitly set forth in the Directions, moisture conditions outside the moisture range specified in the Directions, or the presence of products other than those set forth in the Directions in or on the soil. crop or treated vegetation, This Company does nor warrant any product reformulated or repackaged from this product except in accordance with this Company's stewardship requirements and with express written permission from this Company. For over-lhe-top uses on Roundup Ready crop 'arieties, crop safety and weed control performance are not warranted by Monsanto when this product is used in conjunction with "brown bag" or "bin run" seed saved from previous year's production and replanted. THE EXCLUSIVE REMEDY OF THE USER OR BUYER, AND THE LIMIT OF THE LIABILITY OF THIS COMPANY OR ANY OTHER SELLER FOR ANY AND ALL LOSSES, INJURIES OR DAMAGES RESULTING FROM THE USE OR HANDLIi\G OF THIS PRODUCT (INCLUDING CLAIMS BASED IN COI\TRACT, NEGLIGENCE, STRICT LIABILITY, OTHER TORT OR OTHERWISE) SHALL BE THE PURCHASE PRICE PAlD BY THE USER OR BUYER FOR THE QUANTITY OF THIS PRODUCT INVOLVED, OR, AT THE ELECTION OF THIS COMPANY OR ANY OTHER SELLER, THE REPLACE­ MEJ','T OF SUCH QUANTITY, OR, IF NOT ACQUIRED BY PURCHASE. REPLACEMENT OF SUCH QUANTITY. IN NO EVENT SHALL THIS COMPANY OR ANY OTHER SELLER BE LIABLE FOR ANY INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES Buyer and all users are deemed to have accepted the terms of this LIMIT OF WARRANTY AND LIABILITY which may not be varied by any verbal or wriuen agreement. Bullet, Harness, Lariat, Lasso, Micro- Tech. Partner, and TransSorb are registered trademarks of Monsanto Company. FARMSOURCE.com domain name is a trademark of Monsanto Company. B!ndex, Canopy, Extrazine. Gemini, Karmex. Krovar, Lexone, Lorox and Preview are trademarks of E.I. duPont de Nemours and Company. Bicep, Dual. Princep Caliber. and Solicam are trademarks of Novartis Corporation. Broadstrike Clnd Surflan are trademarks of Dov. E!anco Company. Banvel, Frontier, Guardsman. and Marksman are trademarks of BASF Ltd. Folex and Prep are trademarks of Rhone-Poulenc. Inc. Goal is a trademark of Rohm and Haas Cdmpany. Sencor and Turbo are trademarks of Bayer AG Prow!. Pursuit. Pursuit Plus, Scepter, and Squadron are tradema:--ks of American Cyanamid Company. Command is a trademark of FMC Corporation. DEF is a trademark of Mobay Chemical Company . . Devrinol. Fusion. Surpass, and Topnotch are trademarks of Zeneca Group Company. Direx and Linex are trademarks of Griffen Company. 21-Sep-1999 Page 65 of 66 Roundup D-Pak 99 revise.doc

Sim- Trol is a trademark of Oxon Italia Company. EPA Reg. No. 524-494 This product is protected by U.S. Patent No. 4,405,531. Other patents pending. No license granted under any non-U.S. patent(s). In case of an emergency involving this product, Call Collect, day or night, (314) 694-4000. lDMONSA.''TO COMPANY MONSAi'TO COMPANY ST. LOUIS, MISSOURI, 63167 USA 2l-Sep-1999 Page 66 of 66 Roundup D-Pak 99 revise.doc LL \ 1t

SUPPLEMENTAL LABELING READ THE ENTIRE LABEL FOR ROUNDUP D-PAK T " HERBICIDE BEFORE PROCEEDING WITH THE USE DIRECTIONS CONTAINED IN THIS SUPPLEMENTAL LABELING . .. :;:;-=-;:;-;:-;;::;-:=-='+'i abel" as used in this supplemental labeling refers to the label booklet ACe E PTE D for Roundup D-PAK, container labels and this supplement. Roundup D_PAKTM Herbicide l7ndaP tho Pedor.u -loldc, ; Pungicido, aod RodenUotde Aot, .1' as amended, for 'he P<J<ticlde. EPA Reg. No. 524-494 rogLeteroo. under }:PA Rae. No 'I '\ -' .• (', '! . -'. -'-----.-. -- ,- - -.-~~.-. FOR POSTEMERGENCE APPLICA TIOl\S TO SOYBEANS WITH THE ROUNDUP READY® GENE Keep out of reach of children. CAUTION! In case of an emergency involving this product, Call Collect, day or night, (314) 694-4000. Roundup® and Roundup Ready® are registered trademarks of Monsanto Company. Roundup D_PAK™ is a trademark of Monsanto Company. DIRECTIONS FOR USE It is a violation of Federal law to use this product in any manner inconsistent with its labeling. This label must be in the possession of the user at the time of application. See "GENERAL INFORMATION" and "APPLICATION INSTRUCTIONS" sections of the label booklet for Roundup D-PAK herbicide for essential product performance information. GenendInfonnation MONSANTO COMP.-\NY RECOMMENDS USE OF THIS PRODUCT FOR POSTEMERGENCE APPLICATION ONLY ON SOYBEAN VARIETIES DESIGNATED AS CONTAINING THE ROUNDUP READY® GENE. • Applying this product to soybean "arieties which are not designated as Roundup Ready® will result in severe crop injury and yield loss. Avoid contact with foliage, green stems, or fruit of crops, or any desirable plants which do not contain the Roundup Ready gene, since severe injury or destruction will result. • The Roundup Ready designation indicates that the soybean contains a patented gene which provides tolerance to this herbicide. Information on Roundup Ready soybeans may c· obtained from your seed supplier or Monsanto representative. A pplication Instructions Ll b Ti

---------- . This product may be applied postemergence to Roundup Ready soybeans from the cracking stage throughout flowering. Allow a minimum of 14 days between final application and harvest or feeding of soybean grain, forage or hay. Maximum Allowable Application Rates: • Combined total per year for all applications 5 quarts per acre • Preplant, Preemergence applications 3.2 quarts per acre • Total in-crop applications from cracking throughout flowering 2 quarts per acre • Maximum preharvest application rate 20 fluid ounces per acre When applied as directed, this product will control labeled annual grasses and broadleaf weeds in Roundup Ready soybeans. Many perennial grasses and broadleaf weeds will be controlled or suppressed with one or more applications of this product. PRECAUTIONSIRESTRICTIONS: The combined total application from crop emergence through harvest must not exceed 2 quarts per acre. The maximum rate for any single in crop application is 40 fluid ounces per acre. The maximum combined total of this product which can be applied during flowering is 40 fluid ounces per acre. Allow a minimum of 14 days between final application and harvest of soybean grain. forage or hay. There are no rotational crop restrictions following applications of this product. For ground applications: Use the recommended rates of this product in 5 to 20 gallons of spray solution per acre as a broadcast spray. Carefully select proper nozzle and spray pressure to avoid spraying a fine mist. For best results with ground application equipment, use nozzles which provide a flat fan pattern. Check for even distribution of spray droplets. For aerial applications: Use the recommended rates of this product in 3 to 15 gallons of spray solution per acre. Do not exceed 20 fluid ounces of this product per acre unless otherwise directed. DO NOT APPLY DURING LOW LEVEL INVERSION CONDITIONS, WHEN WINDS ARE GUSTY OR UNDER ANY OTHER CONDITIONS WHICH FAVOR DRIFT. DRIFT MAY CAUSE DAMAGE TO ANY VEGETATION CONTACTED TO WHICH TREATMENT IS NOT INTENDED. MAINTAIN APPROPRIATE BUFFER ZONES TO PREVENT INJURY TO ADJACENT DESIRABLE VEGET A TION. ANNUAL WEED RATE TABLES The following rate recommendations will provide control of labeled grasses and broadlea; weeds in conventional and no-till soybean production systems. Refer to the label booklet for rate recomrra.C:ations for specific annual weeds. Monsanto will not warrant crop safety or weed control when Roundup Ready soybeans. are tl eateii with herbicides not specified on this supplemental label. Because of the potential for; 1) crvp injac·y, 2) poor weed control from antagonism, and/or 3) rotational crop restrictions, herbicide; nyl ~pecified on this supplemental label should not be used, whether applied preemergence or applied postemergence as a tank mixture with Roundup D-PAK. ' '

This product may be used up to 40 fluid ounces per acre in any single application for control of annual weeds, where heavy weed densities exist. NOTE: The following recommendations are based on a clean start at planting by using a bum down application or tillage to control existing weeds before crop emergence, In no-till and stale seedbed systems, a preplant burn-down treatment of 10-40 fluid ounces per acre of this product can be used to control existing weeds prior to crop emergence. MIDWESTI MID-ATLANTIC RECOMMENDATIONS :IIarrow row or drilled soybeans: A single in-crop application of this product will provide effective control of labeled weeds, For best results, an initial application of 20 fluid ounces per acre on 4-8" weeds is recommended, Weeds will generally be 4-8" tall 3 to 5 weeks after planting, If the initial application is delayed and weeds are 8-18" tall, use 30 fluid ounces per acre for best results, Under adverse growing conditions such as drought, hail, wind damage or a poor soybean stand that slows or delays canopy closure, a sequential application of this product at 15 to 20 fluid ounces per acre may be necessary to control late flushes of weeds, Wide row soybeans: An in-crop application of this product will provide effective control of the initial stand of labeled weeds, For best results, an initial application of 20 fluid ounces per acre on 4-8" weeds is recommended, Weeds will generally be 4-8" tall 3 to 5 weeks after planting, If new flushes of weeds occur, they can be controlled by sequential applications of this product. Weed Height (inches) 1-3 4-8 8-18 Initial and Sequential (if needed) Applications Rate (fl oz/A) 15 20 30 Giant ragweed: Apply 20 fluid ounces per acre when the weed is 8-12" tall to avoid the need for sequential application, Black nightshade, Pennsylvania smartweed, velvetleaf, and waterhemp: Apply 20 fluid ounces per acre to weeds 3-6" tall, and 30 fluid ounces per acre when weeds are up to 12" tall. For morningglory species, apply 20 fluid ounces per acre when weeds are up to 4" tall anc 30 :luid ounces per acre when weeds are up to 6" tall. Some weeds, such as black nightshade, woolly cupgrass, shattercane, wild proso millet, bt:r::1:nber, and giant ragweed, with multiple germination times may require a sequenti,,; opplication vf this product. Suppressed or stunted weeds may also require sequential applications, Sequential a;Jplica~ions should be made after some regrowth has occurred, Use a minimum of 15 fluid ounce" o(this product per acre for sequential applications, SOUTHEAST RECOMMENDATIONS

Narrow row, drilled, or wide-row soybeans: An in-crop application of this product will provide effective control of the initial stand of labeled weeds. For best results, an initial application of 20 fluid ounces per acre on 3-6" weeds is recommended. Weeds will generally be 3-6" tall 2 to 3 weeks after planting. Initial Treatment Weed Height linches) 3-6 6-12 Rate (fl ovA) 20 30 Under adverse growing conditions such as drought, hail, wind damage or a poor soybean stand that slows or delays canopy closure, a sequential application of this product at 10 to 20 fluid ounces per acre may be necessary to control late flushes of weeds . . Sequential A pplication (if needed) Weed Height Rate (inches) (fl ovA) 2-3 10 3-6 15 6-12 20 Florida pusley, hemp sesbania and spurred anoda: Apply 20 fluid ounces per acre to weeds 2-4 "for the initial application. Apply 20 fluid ounces per acre when these weeds are 3-6" tall if a sequential application is necessary. Morningglory, black nightshade, groundcherry, and Pennsylvania smartweed: Apply 15 fluid ounces per acre on 1-3" weeds, 20 fluid ounces per acre on 3-6" weeds, or 30 fluid ounces per acre on 6- I 2" weeds for the initial application. Some weeds, such as black nightshade, broadleaf signalgrass, Texas panicum, burcumber, and sicklepod, with mUltiple germination times may require a sequential application of this product. Suppressed or stunted weeds may also require sequential applications: Sequential applications should be made after some regrowth has occurred. Use a minimum of 10 fluid ounces of this product per acre for sequential applications. The combined total of all in-crop postemergence treatments must not exceed 2 quarts (64 fluid ounces) per acre. DEL T AlMID-SOUTH RECOMMENDATIONS Narrow row, drilled, ur wide row soybeans: An in-crop application of this product will rrrwide effective control of the initial stand of labeled weeds. A sequential application will be requ:r:xl to control new flushes of weeds. For best results, an initial application of 20 fluid ouno~~ fM acre (fl ovA), on 2-4" weeds is recommended. Weeds will generally be 2-4" tall 2 to 3 weeks after plantin,g. Initial Treatment

Weed Height (inches) 2-4 5-12 Rate (fl ozlA) 20 30 Sequential Application Weed Height (inches) 2-3 3-6 6-12 Rate (fl ozl A) 10 15 20 Hemp sesbania and spurred anoda: Apply a sequential treatment of 20 fluid ounces per acre on 3- 6"weeds if necessary S9me weeds. such as black nightshade. broadleaf signalgrass. Texas panicum, burcumber. and sicklepod. with multiple germination times may require a sequential application of this product. Suppressed or stunted weeds may also require sequential applications. Sequential applications should be made after some regrowth has occurred. Use a minimum of 10 fluid ounces of this product per acre for sequential applications. PERENNIAL WEEDS RATE RECOMMENDATIONS A 20 to 40 fluid ounces per acre rate (single or multiple applications) of this product will control or suppress perennial weeds such as: bermudagrass. Canada thistle. common milkweed. field bindweed. hemp dogbane. horsenettle. marestail (horseweed). nutsedge. quackgrass. rhizome johnsongrass. redvine. trumpetcreeper. swamp smartweed, and wire stem muhly. For best results, allow perennial weed species to achieve at least 6" of growth before spraying with Roundup D-PAK. For additional information on perennial weeds. see the "PERENNIAL WEED RATE TABLE" of the label booklet for Roundup D-PAK. For some perennial species, repeat application may be required to eliminate crop competition throughout the growing season. Read the "Limit of Warranty and Liability" in the label booklet for Roundup D-PAK herbicide before using. For over-the-top uses on Roundup Ready crop varieties, crop safety and weed control performance are not warranted' by Monsanto when this product is used in conjunction with "brown bag" or "bin run" soybean seed saved from previous year's production and replanted. These terms apply to this supplemental labeling and if these terms are not acceptable, return the product unopened at once. ©Monsanto Company 1999 MONSANTO COMPANY ST. LOUIS. MISSOURl63167 This supplemental label will expire February I. 2001 11b If

SUPPLEMENTAL LABELING READ THE ENTIRE LABEL FOR ROUNDUP D_PAKTM HERBICIDE BEFORE PROCEEDING WITH THE USE DIRECTIONS CONTAINED IN THIS SUPPLEMENTAL LABELING. IACCEPTE / . 11_' .:\ 100 1Jodop tho PederQ) -!CIdo, I i'ung1c1de. and RodenUotdo ADI, ! as amend«1, (or the peat.icide 1 Mundo, ,egNo 1, "'_\ ,,- , -'~~-"-'-'- ---"",, el" as used in this supplemental labeling refers to the label booklet for Roundup D-PAK. container labels and this supplement. Roundup D_PAKTM Herbicide EPA Reg. No. 524-494 FOR POSTEMERGENCE APPLICATIONS TO SOYBEANS WITH THE ROUNDUPREADY®GENE Keep out of reach of children. CAUTION! In case of an emergency involving this product, Call Collect, day or night. (314) 694-4000. Roundup® and Roundup Ready® are registered trademarks of Monsanto Company. Roundup D_PAKTM is a trademark of Monsanto Company. DIRECTIONS FOR USE It is a violation of Federal law to use this product in any manner inconsistent with its labeling. This label must be in the possession of the user at the time of application. See "GENERAL INFORMATION" and "APPLICATION INSTRUCTIONS" sections of the label booklet for Roundup D·PAK herbicide for essential product performance information. General Infonnation MONSANTO COMPANY RECOMMENDS USE OF THIS PRODUCT FOR POSTEMERGENCE APPLICATION ONLY ON SOYBEAN VARIETIES DESIGNATED AS CONTAINING THE ROUNDUP READY®GENE. • Applying this product to soyhean >,arieties which are not designated as Roundup Ready® will result in severe crop injury and yield loss. Avoid contact with foliage. green stems, or fruit of crops, or any desirable plants which do not contain the Roundup Ready gene, since severe i~jury or destruction will result. • The Roundup Ready designation indicates that the soybean contains a patented gene which prQvides tolerance to this herbicide. Information on Roundup Ready soybeans may be obta'ned fr('IT' your seed supplier or Monsanto representative. Application Instructions

This product may be applied postemergence to Roundup Ready soybeans from the cracking stage throughout flowering. Allow a minimum of 14 days between final application and harvest or feeding of soybean grain, forage or hay. Maximum Allowable Application Rates: • Combined total per year for all applications 5 quarts per acre • Preplant, Preemergence applications 3.2 quarts per acre • Total in-crop applications from cracking throughout flowering 2 quarts per acre • Maximum preharvest application rate 20 fluid ounces per acre When applied as directed, this product will control labeled annual grasses and broadleaf weeds in Roundup Ready soybeans. Many perennial grasses and broadleaf weeds will be controlled or suppressed with one or more applications of this product. PRECAUTlONSIRESTRICTlONS: The combined total application from crop emergence through harvest must not exceed 2 quarts per acre. The maximum rate for any single in crop application is 40 fluid ounces per acre. The maximum combined total of this product which can be applied during flowering is 40 fluid ounces per acre. Allow a minimum of 14 days between final application and harvest of soybean grain, forage or hay. There are no rotational crop restrictions following applications of this product. For ground applications: Cse the recommended rates of this product in 5 to 20 gallons of spray solution per acre as a broadcast spray. Carefully select proper nozzle and spray pressure to avoid spraying a fine mist. For best results with ground application equipment, use nozzles which provide a flat fan pattern. Check for even distribution of spray droplets. For aerial applications: Use the recommended rates of thiS product in 3 to 15 gallons of spray solution per acre. Do not exceed 20 fluid ounces of this product per acre unless otherwise directed. DO NOT APPLY DURING LOW LEVEL INVERSION CONDITIONS, WHEN WINDS ARE GUSTY OR UNDER ANY OTHER CONDITIONS WHICH FAVOR DRIFT. DRIFT MAY CAUSE DAMAGE TO ANY VEGETATION CONTACTED TO WHICH TREATMENT IS NOT INTENDED. MAINTAIN APPROPRIATE BUFFER ZONES TO PREVENT INJURY TO ADJACENT DESIRABLE VEGETATION. ANNUAL WEED RATE TABLES The following rate recommendations will provide control of labeled grasses and broadleaf' weeds in conventional and no-till soybean production systems. Refer to the label booklet for rate recomoeridations for specific annual weeds. Monsanto will not warrant crop safety or weed control when Roundup Ready soybc~r.> are treutcJ ·with herbicides not specified on this supplemental label. Because of the potential for; I) crop injur;i, 7) :poor weed control from antagonism, andlor 3) rotational crop restrictions, herbicides not specified on this . , ' , , ' . supplemental label should not be used, whether applied preemergence or applied postemergence .as "tank mixture with Roundup D-PAK. . . .

This product may be used up to 40 fluid ounces per acre in any single application for control of annual weeds, where heavy weed densities exist. NOTE: The following recommendations are based on a clean start at planting by using a bum down application or tillage to control existing weeds before crop emergence. In no-till and stale seedbed systems, a preplant burn-down treatment of 10-40 fluid ounces per acre of this product can be used to control existing weeds prior to crop emergence. MIDWEST/ MID-ATLANTIC RECOMMENDATIONS Narrow row or drilled soybeans: A single in-crop application of this product will provide effective control of labeled weeds. For best results, an initial application of 20 fluid ounces per acre on 4-8" weeds is recommended. Weeds will generally be 4-8" tall 3 to 5 weeks after planting. If the initial application is delayed and weeds are 8-18" tall, use 30 fluid ounces per acre for best results. Under adverse growing conditions such as drought, hail, wind damage or a poor soybean stand that slows or delays canopy closure, a sequential application of this product at 15 to 20 fluid ounces per acre may be necessary to control late flushes of weeds. Wide row soybeans: An in-crop application of this product will provide effective control of the initial stand of labeled weeds. For best results, an initial application of 20 fluid ounces per acre on 4-8" weeds is recommended. Weeds will generally be 4-8" tall 3 to 5 weeks after planting. If new flushes of weeds occur, they can be controlled by sequential applications of this product. Weed Height (inches) 1-3 4-8 8-18 Initial and Sequential (if needed) Applications Rate (fl ozlA) 15 20 30 Giant ragweed: Apply 20 fluid ounces per acre when the weed is 8-12" tall to avoid the need for sequential application. Black nightshade, Pennsylvania smartweed, velvetleaf, and waterhemp: Apply 20 fluid ounces per acre to weeds 3-6" tall, and 30 fluid ounces per acre when weeds are up to 12" tall. For morningglory species, apply 20 fluid ounces per acre when weeds are up to 4" tall an,; :;0 tluid ounces per acre when weeds are up to 6" tall. Some weeds, such as black nightshade, woolly cupgrass, shattercane, wild proso millet, burco.hnber, and giant ragweed, with multiple germination times may require a sequenti?l aPrlication of this product. Suppressed or stunted weeds may also require sequential applications. Seauemial al'plicalions should be made after some regrowth has occurred. Use a minimum of 15 fluid ounces "f'this p~oduct per acre for sequential applications. . SOUTHEAST RECOMMENDATIONS

Narrow row, drilled, or wide-row soybeans: An in-crop application of this product will provide effective control of the initial stand of labeled weeds. For best results, an initial application of 20 fluid ounces per acre on 3-6" weeds is recommended. Weeds will generally be 3-6" tall 2 to 3 weeks after planting. Initial Treatment Weed Height (inches) 3-6 6- \ 2 Rate (fJ oz/A) 20 30 Under adverse growing conditions such as drought. hail, wind damage or a poor soybean stand that s!O\I,iS or delays canopy closure. a sequential application of this product at 10 to 20 flUId ounces per acre may be necessary to comrollate flushes of weeds. Sequential Application (if needed) Weed Height (inches) 2-3 3-6 6-12 Rate (fJ oz/ A) 10 IS 20 Florida pusley, hemp sesbania and spurred anoda: Apply 20 fluid ounces per acre to weeds 2-4"for the initial application. Apply 20 fluid ounces per acre when these weeds are 3-6" tall if a sequential application is necessarv. Morningglory, black nightShade, groundcherry, and Pennsylvania smartweed: Apply 15 fluid ounces per acre on 1-3" weeds, 20 fluid ounces per acre on 3-6" weeds, or 30 tluid ounces per acre on 6-12" weeds for the initial applicatIOn. Some weeds, such as black nightshade, broadleaf signalgrass, Texas panicum, burcumber, and sicklepod, with mUltiple gerrrunation tImes may require a sequential application of this product. Suppressed or stunted weeds may also require sequential applications. Sequential applications should he n:ade after some regrowth has occurred. ese a minimum of 10 fluid ounces of this product per acre for sequential applications. The combined total of all in-crop postemergence treatments must not exceed 2 quarts (64 fluid ounces) per acre. DEL T AlMID-SOUTH RECOMMENDATIONS Narrow row, drilled, or wide row soybeans: An in-crop application of this product will ?covide effective control of the initial stand of labeled weeds. A sequential application will be reyu~too to control new flushes of weeds. For best results, an initial application of 20 fluid oupses per acre (fl ozlA), on ::-4" weeds is recommended. Weeds will generally be 2-4" tall 2 to 3 weeks after planting. Initial Treatment

Weed Height (inches) 2-4 5-12 Rate (fl ozl A) 20 30 Sequential Application Weed Height (inches) 2-3 3-6 6-12 Rate (fl ozl A) 10 15 20 Hemp sesbania and spurred anoda: Apply a sequential treatment of 20 fluid ounces per acre on 3- 6"weeds if necessary Spme weeds, such as black nightshade, broadleaf signalgrass, Texas panicum, burcumber, and sicklepod, with multiple germination times may require a sequential application of this product. Suppressed or stunted weeds may also require sequential applications. Sequential applications should be made after some regrowth has occurred. Use a minimum of 10 fluid ounces of this product per acre for sequential applications. PERENNIAL WEEDS RATE RECOMMENDA TJONS A 20 to 40 fluid ounces per acre rate (single or multiple applications) of this product will control or suppress perennial weeds such as: bermudagrass, Canada thistle, common milkweed, field bindweed, hemp dogbane, horsenettle, marestail (horseweed), nutsedge, quackgrass, rhizome johnsongrass. redvine, trumpetcreeper. swamp smartweed, and wirestem muhly. For best results, allow perennial weed species to achieve at least 6" of growth before spraying with Roundup D-PAK. For additional information on perennial weeds, see the "PERENNIAL WEED RATE TABLE" of the label booklet for Roundup D-PAK. For some perennial species, repea. application may be required to eliminate crop competition throughout the growing season. Read the "Limit of Warrant)' and Liability" in the label booklet for Roundup D-PAK herbicide before using, For over-the-top uses on Roundup Ready crop varieties, crop safety and weed control performance are not warranted by Monsanto when this product is used in conjunction with "brown bag" or "bin run" soybean seed saved from previous year's production and replanted. These terms apply to this supplemental labeling and if these terms are not acceptable, return the product unopened at once, ©Monsanto Company 1999 MONSANTO COMPANY ST. LOUIS, MISSOURI 63167 This supplemental label will expire February 1. 200J

SUPPLEMENTAL LABELING READ THE ENTIRE LABEL FOR ROUNDUP D-PAKTM HERBICIDE BEFORE PROCEEDING WITH THE USE DIRECTIONS CONTAINED IN THIS SUPPLEMENTAL LABELING. "Label" as used in this supplemental labeling refers to the label booklet for Roundup D-PAK herbicide, container labels and this supplement. jACCEPTED ., :' NC.) / ;1 ' 4 1999 ~ I Under the Pect.ral -,<>Ide, I Fungicide. and Rodantlolde ADI.. I "" MlMdOO, for tho pootlcllb I ! g!..a:tarod. cndJr ' ~ BPA He,s. No S~\ '-I. ('l J --" •• - -- -----., •••• _. __ -'." • ---- _ .............. r EPA Aeg. No. 524·494 Roundup D·PAK is a trademark. and Roundup Ready" is a registered trademark of Monsanto Company. FOR POSTEMERGENCE APPLICATIONS TO CORN WITH THE ROUNDUP READy@' GENE Keep out of reach of children. CAUTION! In case of emergency involving this product, Call Collect, day or night, 314-694-4000 . DIRECTIONS FOR USE It IS a violation of Federal law to use this product in any manner inconsistent " witn its labeling. This label must be in the possession of the user at the time of application. AVOID CONTACT OF HERBICIDE WITH FOLIAGE. GREEN STEMS. EXPOSED NON·WOODY ROOTS OR FRUIT OF CROPS. (EXCEPT AS SPECIFIED FOR INDIVIDUAL ROUNDUP READY' CROPS) DESIRABLE PLANTS AND TREES. OTHER THAN CORN WITH THE ROUNDUP READY GENE. BECAUSE SEVERE INJURY OR DESTRUCTION MAY RESULT. See "GENERAL INFORMATION" and "MIXING" seclions of Ihe label booklet for Roundup D-PAKn .. herbicide for essential product performance inlormation. GENERAL INFORMATION MONSANTO COMPANY RECOMMENDS USE OF THIS PRODUCT ONLY ON CORN HYBRIDS DESIGNATED AS CONTAINING THE ROUNDUP READY GENE. • Applying this producl 10 corn hybrids which are not designated as Roundup Ready will result in severe crop injury and yield loss. • The Roundup Ready designation indicates that the corn contains a patented gene which provides tolerance to this herbicide. Information on Roundup Ready corn may be oblained from your seed supplier or Monsanto representative. Application Instructions This product may be applied postemergence to Roundup Ready corn from emergence through the va stage (8 leaves with collars) or until corn height reaches 30 inches, whichever comes first. Single in-crop applications of this producl are nol 10 exceed 20 fluid ounces per acre. Sequenlial in·crop applicalions of Ihis producl from emergence through the VB stage or 30 inches must not exceed 40 fluid ounces per acre per growing season, Maximum Yearly Rates AII0 .... E.d Preplant: Maximum amount of this product which cur, Jt: applied prior to crop emergence is 3.2 quarts per aCT, In-crop: Maximum combined total, /"If ""JIiple in-.::rop .:.pplications from emergence Ihrough the VB stage or 30 Ihores is 40 fluid .(J.lees per acre. Preharvest: Maximum amount 01 I's: rooduct Ihat can be applied afler maximum kernal fill is complele and Ihe crop is .phyoiologically malure (black layer formation) unlil 7 days before harvest b 20 fluid ounces per acre . Cropping Seagoo: Combined total pBr year for all applicalions may not exceed 5 quarts per acre.

When applied s directed., this product controls labeled annual grass and broadleal weeds in Roundup Ready com. Many perennial grasses and broadleal weeds win be controlled or suppressed with one or more appllcallons 01 Ihls product. Appllcalions should be made 10 actively growing weeds belore Ihey reach the maximum size lisled in Ihe "WEEDS CONTROLLED" secllon of Ihe label booklet for Roundup D-PAK herbicide. Relel 10 Ihe "MIXING" secllon of the label booklel fOI proper use instructions. The add,l,on 01 1 10 2 percent dry ammonium suilate by weighl or 8.5 10 17 pounds per 100 gallons 01 waler may increase Ihe perlormance of Ihis product unoer hard water conditions, drought conditions or when tank mixed with 8uilet:!. Micro-Tech@' or Partner(O) herbicides. Ensure that ammonium sullate IS complelely dissolved In Ihe spray tank belore adding herbicides. Thoroughly rinse the spray system with clean water alter use to reduce corrOSIOn, The addition of other additives, including fertilizers and micro­ nutrients ae not recommendeG with this product since this may result in increased potential tor crop injL.,,,! Aliow a mlr;,mum 01 50 days be(ween application Ollhis product and harvest ot corn forage and 7 days between application and harvest 01 corn grain. Allow a mmimum 01 10 days between in-crop applications of this product. There are no rotational crop restrictions following applications of this ,\lroducl ATIENTION: AVOID DRIFT. EXTREME CARE MUST BE USED WHEN APPLYING THIS PRODUCT TO PREVENT INJURY TO DESIRABLE PLANTS AND CROPS WHICH DO NOT CONTAIN THE ROUNDUP READY GENE. THOROUGHLY CLEAN THE SPRAY TANK AND ALL LINES AND FILTERS TO ELIMINATE POTENTIAL CONTAMINATION FROM OTHER HERBI-CIDES PRIOR TO MIXING AND APPLYING THIS PRODUCT. For around applications: Use Ihe recommended rates of this product in 5 to 20 gallons 0' spray so)uf)on per acre as a broadcast spray. CarefuUy select correct nozzles and spray pressure to avoid spraying a fine mist. Check for even dislrioution of spray droplets. For aerial aoplications: Use the recommended rates of this product in 3 to 15 gallons 01 spray solution per acre. Do nOI exceed 20 fluid ounces per acre. See "WEEDS CONTROLLED" section on IhlS label. AVOID DRIFT - \00 NOT APPLY DURING INVERSION CONDITIONS, WHEN WINOS ARE GUSTY DR UNDER ANY OTHER CONDITIONS WHICH FAVOR DRIFT. DRIFT MAY CAUSE DAMAGE TO ANY VEGETATION CONTACTED TO WHICH TREATMENT IS NOT INTENDED. TO PREVENT INJURY TO ADJACENT VEGETATION, APPROPRIATE BUFFER ZONES MUST BE MAINTAINED. Weed Control Recommendations Apply 15 10 20 IIuid ounces 01 Roundup D-P AK herbicide per acre for control ot labeled grasses and broadleaf weeds in convenlional and no-lill com production systems. Reter to the label booklet for Roundup D-PAK herbicide for rate recommendations for specific annual weeds. Roundup O-PAK herbicide applied al up 10 20 tluid ounces per acre will conlrol or suppress Ihe growth of perennial weeds such as: bermudagrass, Canada Ihislle, common milkweed, tield bindweed, hemp dogbane, horsenettle, nulsedge" quackgrass, rhizome johnsongrass, redvine, !rumpetcreeper, swamp smartweed, and wirestem muh!y. FOI additional information on perennial weeds, see the "PERENNIAL WEED RATE TABLE" of the label oookiellor Roundup D-PAK herbicide. . Preemergence followed by Poslemergence Weed Conlrol Program This producl may be applied poslemergence in-crop following any labeled preemergence herbicide applicalion. The. posl application of this producl should be made before the weeds reach a heighl andlor density Ihal Ihe weeds become competilive wlih Ihe crop. A Single In-crop appllcalion of Ihis 1'b1t product at the recommended rate will provide control ot emerged weeds listed on the label. This product may be applied poslemergence 10 Roundup Ready com from emergence Ihrough Ihe V8 sla!?, 18 leaves with collars) or unlil corn height reaches 30 inches lfTee slanding), whichever comes flfst. Poslemergence Only Weed Conirol Program This producl may be applied alone as a poslemergence IO-crop applicallon 10 provide conlrol of emerged weeds lisled on Ihe label. The poslemer!?,nce applicalion 01 Ihis producl should be ·made belore Ihe weeds reach a height andior density Ihal the weeds become compelilive with Ihe crop. It new flushes of weeds occur, a sequenlial application at Ihis producl al 15 to 20 fluid ounces per acre will conlrol Ihe labeled grasses and broadleat weeds. This producl may be applied poslemergence 10 Roundup Ready corn Irom emergence through the V8 stage or until com heighl reaches 30 inches (Iree standing), whichever comes first. This product may be applied in tank mixture with a labeled rate 0\ Harne?s", Harness Xtra, Harness Xtra 5,6L. Micro-Tech, Bullet, Partner. Permit~ or atrazine. Refer to the specific product lace1 and observe all precautions and limitations on the label tor a:1 produc~s used in tank mixtures. includ:ng applicahon timing restriclions. soil restrictions, minimum re-cropping interval and rotational guidelines - the more restrictive requirements apply. Tank mixtures with other products may result in increased potential for crop injury andlor weed antagonism. Reier to the table below for height limitation for lank mix partner. Maximum Height Of Com Tank Mix Partner For APPlication Harness " inches Harness Xtfa Harness XUa 5.6L Bullel' 5 Inches Micro-Tech" Partner' Permit 24 inches Alrazine 12 inches ~Buttet, Micro-Tech and Partner are not registered lor use as a postemergence application in Texas. Bullet, Harness, Micro-Tech and Partner are registered trademarks 01 Monsanto Company. Permit is a trademark at, and used under license from. Nissan Chemica! Industries, Ltd, Read the 'UMIT OF WARRANTY AND UABIUTY" in the labef booklet for Roundup D-PAK hertlicide before usill!t For over-the-top uses on Roundup Ready crop varieties, crop safety and weed control per-formance ale not warranted by Monsanto 'hn this product is used in conjuction v.ith 'brov.!1 bag" or 'bin run" seed saved from the pre-vious yea"s productions aro replanted. These tenns apply to this supplementaf labeling aro ff these terms are not acceptable, return the product unopellP.<:t itt O,lC'e. ©1999 MONSANTO COMPANY ST. LOUIS, MISSOUAI63167 This supplemenlallabel expires Febraury " 2001.