crop-chem-docs/corpus/epa_ppls/7969-247.md

MULTIVA FUNGICIDE

• EPA Reg No: 7969-247
• Registrant: BASF AGRICULTURAL SOLUTIONS US, LLC
• Signal word: Warning
• Active ingredients: Pyraclostrobin (12%); Metconazole (7.4%)
• Label accepted: 2013-09-05
• Source PDF: https://www3.epa.gov/pesticides/chem_search/ppls/007969-00247-20130905.pdf

---

/ /A/ UNITED STATES ENVIRONMENTAL PROTECTION AGENCY WASHINGTON, D.C. 20460 OFFICE OF CHEMICAL, SAFETY AND POLLUTION PREVENTION David Haughey BASF Corporation PO Box 13528 26 Davis Dr SEP 0 5 2013 Research Triangle Park, NC 27709 Subject: Labeling Amendment to Multiva Fungicide EPA Registration No. 7969-247 Decision No. 465129 PP#2F8038 (Decision #465133) Submission Date: 5/7/12 Dear Mr Haughey: The master and supplemental labeling referred to above, submitted under the Federal Insecticide, Fungicide, and Rodenticide Act, as amended to add use directions for sugarcane, is unconditionally acceptable under FIFRA section 3(c)(5). On the supplemental label in the statement "This supplemental label expires December 31, 2015 and must not be used or distributed after this date," replace the date "December 31, 2015" with the date three years from the date of this letter. As per the Agency's Environmental Risk Assessment, if you plan to submit new uses for this mixture of active ingredients, a valid bee ac.ute contact study is requested to further characterize the possible risk. A stamped copy of the master and supplemental label is enclosed for your records. Please submit one (1) final printed copy for the above mentioned label before releasing the product for shipment. If you have any questions, please contact Dominic Schuler at (703) 347-0260 or via email at schuler.dominic@epa.gov. Sincerely, Tony Kish Product Manager 22 Fungicide Branch Registration Division (7504P)

r •BASFThe Chemical Company Group SEP 0 5 2013 Ufedet the fttdoMl Inseettcfeia, FttngMda. dad ftettautddo Act. me tim»itd*& tot tha pestldds Inadte "••• Ji/U Fungicide Itivafungicide TM For use in disease control and plant health in the following crops: barley, corn, cotton, oats, rye, soybeans, sugar beets, sugarcane, triticale, and wheat Active Ingredients: pyraclostrobin: (carbamic acid, [2-[[[1-(4-chlorophenyl)-1H- pyrazol-3-yl]oxy]methyl]phenyl]methoxy-,methyl ester) 12.0% metconazole: 5-[(4-chlorophenyl)methyl]-2,2-dimethyl-1 - (1/-/-1,2,4-triazol-1-ylmethyl)cyclopentanol 7.4% Other Ingredients***: 80.6% Total: . . i '. . 100.0%

• Equivalent to 1.083 pounds of pyraclostrobin per gallon ** Equivalent to 0.67 pound of metconazole per gallon *** Contains petroleum distillates EPA Reg. No. 7969-247 KEEP OUT OF REACH OF CHILDREN WARNING/AVISO EPA Est. No. Si usted no entiende la etiqueta, busque a alguien para que se la explique a usted en detalle. (If you do not understand this label, find someone to explain it to you in detail.) See inside for complete First Aid, Precautionary Statements, Directions For Use, Conditions of Sale and Warranty, and state-specific crop and/or use site restrictions. In case of an emergency endangering life or property involving this product, call day or night 1-800-832-HELP (4357). Net Contents: BASF Corporation 26 Davis Drive, Research Triangle Park, NC 27709

f' FIRST AID If swallowed If in eyes If on skin or clothing If inhaled • Call a poison control center or doctor immediately for treatment advice. • DO NOT give any liquid to the person. • DO NOT induce vomiting unless told to do so by a poison control center or doctor. • DO NOT give anything to an unconscious person. • Hold eyes open and rinse slowly and gently with water for 1 5 to 20 minutes. • Remove contact lenses, if present, after first 5 minutes; then continue rinsing eyes. • Call a poison control center for treatment advice. • Take off contaminated clothing. • Rinse skin immediately with plenty of water for 1 5 to 20 minutes. • Call a poison control center or doctor for treatment advice. • Move person to fresh air. • If person is not breathing, call 91 1 or an ambulance; then give artificial respiration, preferably mouth to mouth, if possible. • Call a poison control center for further treatment advice. Note to physician: Probable mucosal damage may contraindicate the use of gastric lavage. Contains petroleum distillates - vomiting may cause aspiration pneumonia. HOTLINE NUMBER Have the product container or label with you when calling a poison control center or doctor or going for treatment. You may also contact BASF Corporation for emergency medical treatment information at 1-800-832-HELP (4357). Precautionary Statements Hazards to Humans and Domestic Animals WARNING. May be fatal if swallowed. Causes substantial but temporary eye injury. DO NOT get in eyes or clothing. Harmful if inhaled. Avoid breathing vapor or spray mist. Personal Protective Equipment (PPE) Some materials that are chemically resistant to this product are listed below. For more options, refer to Category A on an EPA chemical-resistance category selection chart. Applicators and other handlers must wear: • Coveralls over short-sleeved shirt and short pants • Protective eyewear (goggles, face shield, or safety glasses with front, brow, and temple protection) • Socks • Chemical-resistant footwear • Chemical-resistant gloves made of any waterproof material (such as nitrile, butyl, neoprene and/or barrier laminate) • Chemical-resistant headgear for overhead exposure • Chemical-resistant apron when cleaning equipment, mixing, and loading Follow the manufacturer's instructions for cleaning and maintaining PPE. If no such instructions for washables exist, use detergent and hot water. Keep and wash PPE separately from other laundry. Engineering Controls Statement When handlers use closed systems, enclosed cabs, or aircraft in a manner that meets the requirements listed in the Worker Protection Standard (WPS) for agricultural pesticides [40 CFR 170.240 (d) (4-6)], the handler PPE requirements may be reduced or modified as specified in the WPS. USER SAFETY RECOMMENDATIONS Users should: • Wash hands before eating, drinking, chewing gum, using tobacco, or using the toilet. • Remove ciothing/PPE immediately if pesticide gets inside. Then wash thoroughly and put on clean clothing. • Remove PPE immediately after handling this product. Wash the outside of gloves before removing. As soon as possible, wash thoroughly and change into clean clothing. Environmental Hazards This pesticide is toxic to birds, mammals, fish and aquatic invertebrates. Drift or runoff may be hazardous to aquatic organisms in water adjacent to treated areas. DO NOT apply directly to water, or to areas where surface water is present, or to intertidarareas below the mean high water mark. DO NOT contaminate water when disposing of equipment wash water or rinsate. DO NOT discharge effluent containing this product into lakes, streams, ponds, estuaries, oceans, or other waters unless in accordance with the requirements of a National Pollutant Discharge Elimination System (NPDES) permit and the permitting authority has been notified in writing prior to discharge. DO NOT discharge effluent containing this product to sewer systems without previously notifying the local sewage treatment plant authority. For guidance, contact your State Water Board or Regional Office of the EPA.

This product is toxic to bees exposed to direct treatment or residues on blooming crops or weeds. DO NOT apply this product if bees are visiting the treatment area. Groundwater Advisory This chemical has properties and characteristics associat- ed with chemicals detected in groundwater. The use of this chemical in areas where soils are permeable, particularly where the water table is shallow, may result in groundwater contamination. Surface Water Advisory Metconazole and pyraclostrobin may impact surface water quality through spray and runoff of rain water. This product has a high potential for runoff for several months or more after application. Poorly draining soils or soils with shallow water tables are more prone to produce runoff that con- tains this product. A level, well-maintained vegetative buffer strip between areas to which this product is applied and surface water features, such as ponds, streams, and springs, will reduce the potential for contamination of water from rainfall runoff. Runoff of this product will be reduced by avoiding applications when rainfall is forecast to occur within 48 hours. Sound erosion control practices will reduce this product's contribution to surface water contamination. Directions For Use It is a violation of federal law to use this product in a man- ner inconsistent with its labeling. DO NOT apply this product in a way that will contact workers or other per- sons, either directly or through drift. Only protected handlers may be in the area during application. For any requirements specific to your state or tribe, consult the agency responsible for pesticide regulation. AGRICULTURAL USE REQUIREMENTS Use this product only in accordance with its labeling and with the Worker Protection Standard (WPS), 40 CFR part 170. This standard contains requirements for the protec- tion of agricultural workers on farms, forests, nurseries, and greenhouses, and-handlers of agricultural pesticides. It contains requirements for training, decontamination, notifi- cation, and emergency assistance. It also contains specific instructions and exceptions pertaining to the statements on this label, about personal protective equipment (PPE), notification to workers, and restricted-entry interval. The requirements in this box only apply to uses of this product that are covered by the Worker Protection Standard. DO NOT enter or allow worker entry into treated areas dur- ing the restricted-entry interval (REI) of 12 hours for all crops. PPE required for early entry to treated areas that is permit- ted under the Worker Protection Standard and that involves contact with anything that has been treated, such as plants, soil, or water, is: • Coveralls • Protective eyewear (goggles, face shield, or safety glasses with front, brow, and. temple protection) • Chemical-resistant gloves made of any waterproof material (such as nitrile, butyl, neoprene, and/or barrier laminate) • Shoes plus socks

STORAGE AND DISPOSAL DO NOT contaminate water, food or feed by storage or disposal. Pesticide Storage Store in original containers only. Keep container closed when not in use. DO NOT store near food or feed. Pesticide Disposal Wastes resulting from using this product may be disposed of on-site or at an approved waste disposal facility. If these wastes cannot be disposed of according to label instructions, contact your State Pesticide or Environmental Control Agency, or the Hazardous Waste representatives at the nearest EPA Regional Office for guidance. Container Handling Nonrefillable Container. DO NOT reuse or refill this container. Triple rinse or pressure rinse container (or equivalent) promptly after emptying; then offer for recy- cling, if available, or reconditioning, if appropriate, or puncture and dispose of in a sanitary landfill, or by inciner- ation, or by other procedures approved by state and local authorities. Triple rinse containers small enough to shake (capacity £ 5 gallons) as follows: Empty the remaining contents into application equipment or a mix tank and drain for 10 seconds after the flow begins to drip. Fill the container 1/4 full with water and recap. Shake for 10 sec- onds. Pour rinsate into application equipment or a mix tank, or store rinsate for later use or disposal. Drain for 10 seconds after the flow begins to drip. Repeat this pro- cedure two more times. Triple rinse containers too large to shake (capacity > 5 gallons) as follows: Empty the remaining contents into application equipment or a mix tank. Fill the container 1/4 full with water. Replace and tighten clo- sures. Tip container on its side and roll it back and forth, ensuring at least one complete revolution, for 30 seconds. Stand the container on its end and tip it back and forth several times. Turn the container over onto its other end and tip it back and forth several times. Empty the rinsate into application equipment or a mix tank, or store rinsate for later use or disposal. Repeat this procedure two more times. Pressure rinse as follows: Empty the remaining con- tents into application equipment or mix tank and continue to drain for 10 seconds after the flow begins to drip. Hold container upside down over application equipment or mix tank, or collect rinsate for later use or disposal. Insert pressure rinsing nozzle in the side of the container and rinse at about 40 PSI for at least 30 seconds. Drain for 10 seconds after the flow begins to drip. STORAGE AND DISPOSAL (continued) Container Handling (continued) Refutable Container. Refill this container with pesticide only. DO NOT reuse this container for any other purpose. Triple rinsing the container before final disposal is the responsibility of the person disposing of the container. Cleaning before refilling is the responsibility of the refiller. Triple rinse as follows: To clean the container before final disposal, empty the remaining contents from this container into application equipment or mix tank. Fill the container about 10% full with water. Agitate vigorously or recirculate water with the pump for 2 minutes. Pour or pump rinsate into application equipment or rinsate collec- tion system. Repeat this rinsing procedure two more times. When this container is empty, replace the cap and seal all openings that have, been opened during use; return the container to the point of purchase or to a designated location. This container must only be refilled with a pesti- cide product. Prior to refilling, inspect carefully for damage such as cracks, punctures, abrasions, worn-out threads and closure devices. Check for leaks after refilling and before transport. DO NOT transport if this container is damaged or leaking. If the container is damaged, or leak- ing, or obsolete and not returned to the point of purchase or to a designated location, triple rinse emptied container and offer for recycling, if available, or dispose of container in compliance with state and local regulations. In Case of Emergency In case of large-scale spillage regarding this product, call: •CHEMTREC 1-800-424-9300 • BASF Corporation 1 -800-832-HELP (4357) In case of medical emergency regarding this product, call: • Your local doctor for immediate treatment • Your local poison control center (hospital) • BASF Corporation 1 -800-832-HELP (4357) Steps to be taken in case material is released or spilled: • In case of spill on floor or paved surfaces, mop and remove to chemical waste storage area until proper dis- posal can be made if product cannot be used according to label. • Dike and contain the spill with inert material (sand, earth, etc.) and transfer liquid and solid diking material to sepa- rate containers for disposal. • Remove contaminated clothing and wash affected skin areas with soap and water. • Wash clothing before reuse. • Keep the spill out of all sewers and open bodies of water. (continued)

6J2-I Product Information Multiva™ fungicide is a broad-spectrum fungicide con- taining two active ingredients, pyraclostrobin and metconazole. Multiva provides systemic, curative and long-lasting residual control of target plant diseases. To maximize disease control, apply Multiva in a regularly scheduled protective spray program and use in a rotation program with other fungicides. Preventative applications of Multiva optimize disease con- trol resulting in improved plant health. The increase in plant health comes from the combined effect of disease control (including fungal diseases listed in Crop-specific directions), improved growth efficiency and improved stress tolerance. Overall increased plant health may result in an improve- ment in crop growth and crop quality as well as increased crop yields. Information regarding the contents and levels of metals in this product is available on the Internet at http://www.aapfco.org/metals.htm. Multiva is not for use in greenhouse or transplant production. Mode of Action Each of the components in Multiva provides a different mode of action against plant pathogenic fungi. Pyraclostrobin belongs to the group of respiration inhibitors classified by the US EPA and Canada PMRA as Quinone Outside Inhibitors (Qol) or target site of action Group 11 fungicides. Metconazole inhibits demethylation of sterol biosynthesis (DMI), disrupting cell membrane synthesis or target site of action Group 3 fungicides. Resistance Management Multiva contains pyraclostrobin, a Group 11 fungicide, and is effective against pathogens resistant to fungicides with modes of action different from those of Qol fungicides (target site Group 11), such as dicarboximides, sterol inhibitors, benzimidazoles, or phenylamides. Fungal isolates resistant to Group 11 fungicides, such as pyraclostrobin, azoxystrobin, fluoxastrobin, trifloxystrobin, and kresoxim-methyl, can eventually dominate the fungal population if Group 11 fungicides are used predominantly and repeatedly in the same field in successive years as the primary method of control for the targeted pathogen species. This can result in reduction of disease control by Multiva or other Group 11 fungicides. To maintain the performance of Multiva in the field, DO NOT exceed the maximum seasonal use rate or the total number of applications of Multiva per season and the maximum number of applications of Multiva stated in Restrictions and Limitations - All Crops and Table 2. Multiva™ fungicide Crop-specific Requirements. Follow the label instructions for use of Multiva or other target site of action Group 11 fungicides that have a similar site of action on the same pathogens. Resistance Management Advisory The following instructions may delay the development of fungicide resistance:

1. Tank Mixtures - Use tank mixtures with effective fungi- cides from different target site of action groups that are registered/permitted for the same use and that are effec- tive against the pathogens of concern. Use at least the minimum labeled rates of each fungicide in the tank mix.
2. IPM - Integrate Multiva into an overall disease and pest management program. Follow cultural practices known to reduce disease development. Consult your local extension specialist, certified crop advisor and/or BASF representative for additional IPM strategies established for your area. Multiva can be used in agricultural exten- sion advisory (disease forecasting) programs which recommend application timing based on environmental factors favorable for .disease development.
3. Monitoring - Monitor efficacy of all fungicides used in the disease management program against the targeted pathogen and record other factors that may influence fungicide performance and/or disease development. Cleaning Spray Equipment Clean spray equipment thoroughly before and after apply- ing this product, particularly if a product with the potential to injure crops was used prior to Multiva. Directions For Use Through Sprinkler Irrigation Systems Sprayer Preparation Chemical tank and injector system must be thoroughly cleaned. Flush system with clean water. Application Instructions Apply Multiva at rates and timings as required in this label. Use Directions for Sprinkler Irrigation Applications • Apply this product only through sprinkler irrigation sys- tems including center pivot, lateral move, end tow, side [wheel] roll, traveler, big gun, solid set, or hand move irri- gation systems. DO NOT apply this product through any other type of irrigation system. • Add this product to the pesticide supply tank containing sufficient water to maintain a continuous flow by the injection equipment. In continuous moving systems, inject this product/water mixture continuously, applying the labeled rate per acre for that crop. DO NOT exceed 1/2 inch (13,577 gallons) per acre. In stationary or non- continuous moving systems, inject the product/water mixture in the last 15 to 30 minutes of each set allowing sufficient time for all of the required pesticide to be applied by all the sprinkler heads and applying the

rlabeled rate per acre for that crop. DO NOT apply when wind speed favors drift beyond the area intended for treatment. Crop injury, lack of effectiveness, or illegal pesticide residues in the crop can result from non-uni- form distribution of treated water. Thorough coverage of foliage is required for good control. Good agitation should be maintained during the entire application period. • If you have questions about calibration, you should con- tact state extension service specialists, equipment manufacturers or other experts. • The system must contain a functional check valve, vacuum-relief valve, and low-pressure drain appropriately located on the irrigation pipeline to prevent water-source contamination from backflow. • The pesticide injection pipeline must contain a functional, automatic, quick-closing check valve to prevent the flow of fluid back toward the injection pump. • The pesticide injection pipeline must also contain a func- tional, normally closed, solenoid-operated valve located on the intake side of the injection pump and connected to the system interlock to prevent fluid from being with- drawn from the supply tank when the irrigation system is either automatically or manually shut down. • The system must contain functional interlocking controls to automatically shut off the pesticide-injection pump when the water pump motor stops. • The irrigation line or water pump must include a function- al pressure switch that will stop the water pump motor when the water pressure decreases to the point where pesticide distribution is adversely affected. • Systems must use a metering pump, such as a positive displacement injection pump (e.g. diaphragm pump), effectively designed and constructed of materials that are compatible with pesticides and capable of being fitted with a system interlock. • Allow sufficient time for pesticide to be flushed through all lines and all nozzles before turning off irrigation water. A person knowledgeable of the chemigation system and responsible for its operation, or under supervision of the responsible person, shall shut the system down and make necessary adjustments should the need arise. • DO NOT connect an irrigation system used for pesticide application to a public water system unless the pesticide label-prescribed safety devices for public water systems are in place. Specific Instructions for Public Water Systems

1. Public water system means a system for the provision to the public of piped water for human consumption if such system has at least 15 service connections or regularly serves an average of at least 25 individuals daily at least 60 days out of the year.
2. Chemigation systems connected to public water sys- tems must contain a functional, reduced-pressure zone, back-flow preventer (RPZ) or the functional equivalent in the water supply line upstream from the point of pesti- cide introduction. As an option to the RPZ, the water from the public water system should be discharged into a reservoir tank prior to pesticide introduction. There shall be a complete physical break (air gap) between the outlet end of the fill pipe and the top or overflow rim of the reservoir tank of at least twice the inside diameter of the fill pipe.
3. The pesticide injection pipeline must contain a function- al, automatic, quick-closing check valve to prevent the flow of fluid back toward the injection pump.
4. The pesticide injection pipeline must contain a function- al, normally closed, solenoid-operated valve located on the intake side of the injection pump and connected to the system interlock to prevent fluid from being with- drawn from the supply tank when the irrigation system is either automatically or manually shut down.
5. The system must contain functional interlocking controls to automatically shut off the pesticide injection pump when the water pump motor stops, or in cases where there is no water pump, when the water pressure decreases to the point where pesticide distribution is adversely affected.
6. Systems must use a metering pump, such as a positive displacement injection pump (e.g. diaphragm pump), effectively designed and constructed of materials that are compatible with pesticides and capable of being fit- ted with a system interlock. Application Instructions Apply Multiva™ fungicide rates as instructed by Table 2. Multiva™ fungicide Crop-specific Requirements. Apply Multiva with ground sprayer, aerial equipment or through sprinkler irrigation equipment. Check equipment frequently for calibration. Under low-level disease conditions, use minimum applica- tion rates. For severe or threatening disease conditions, use maximum application rates and shortened intervals. Ground Application DO NOT use less than. 5 gallons per acre (gpa) sray vol- ume for ground applications. Thorough coverage of foliage, blooms, and fruit is required for optimum disease control. The use of a nonionic surfactant at the lowest labeled rate may be used to improve spray coverage. Refer to the adju- vant product label for specific use directions. DO NOT use adjuvants that contain methylated seed oil, crop oil concentrate or crop oil with emulsifier properties. For ground application .to corn, refer to the Adjuvant or Crop Oil Use Limitations on Corn. Aerial Application For aerial application in New York State, DO NOT apply within 100 feet of aquatic habitats (such as, but not limited to lakes, reservoirs, rivers, streams,

• 11marshes, ponds, estuaries, and commercial fish ponds). DO NOT apply when conditions favor drift from target area. DO NOT use less than 2 gallons per acre (gpa) spray volume on barley, oats, rye, soybean, and sugarcane. DO NOT use less than 5 gallons per acre (gpa) spray vol- ume on cotton and sugar beets. Aerial applications of Multiva™ fungicide can be made to corn, triticale, and wheat in water volumes of 1 or more gallons per acre (gpa) of spray solution. A combination of spray nozzles and appropriate pressure should be selected to provide ASABE Standard S571.1 droplet size category of fine (Dyo.5 of > 180 urn) or coarser than fine. When appli- cations are made with a cross-wind, the swath needs to be displaced downwind. The applicator should compensate for this displacement at the downwind edge of the application area by adjusting the path of the aircraft. Aerial applicator needs to leave at least half swath unsprayed at the downwind edge of the treated area. For all aerial application volumes (gpa), the use of a non- ionic surfactant at the lowest labeled rate can be used to improve spray coverage. Refer to the adjuvant product label for specific use directions. Refer to Adjuvant or Crop Oil Use Limitations on Corn. DO NOT use adjuvants that contain methylated seed oil, crop oil concentrate or crop oil with emulsifier properties. Select spray nozzles, pumping pressure, and sprayer height to provide medium- to-fine spray droplets that penetrate throughout the crop canopy. Spray calibration must be conducted to confirm spray droplet sizes. Continue to monitor spray application (including weather conditions) to assure proper droplet size and canopy penetration. Adjuvant or Crop Oil Use Limitations on Corn Adjuvant crop damage can occur when an adjuvant or crop oil is used after the V8 stage and before the VT stage (the VT stage is defined as when the tassel's last branch is completely visible outside the whorl). If an adjuvant or crop oil is used after the V8 stage and before the VT stage, the grower and user are responsible for contacting the adju- vant source (adjuvant distributor, retailer, or manufacturer) for advice and confirmation that the adjuvant has been tested and proven to be safe for application from V8 to VT corn stage. Refer to adjuvant and/or crop oil labels for spe- cific use directions and restrictions. Always follow the most restrictive label. Another fungicide or an insecticide may be included in the tank mix if needed and labeled for use on corn. Refer to the tank mix pesticide product labels for specific use direc- tions and restrictions. Always follow the most restrictive label. Spray Drift Management DO NOT spray when conditions favor drift beyond area intended for application. Conditions which may contribute to drift include thermal inversion, wind speed and direction, spray nozzle/pressure combinations, spray droplet size, temperature/humidity, etc. Contact your state extension agent for spray drift prevention guidelines in your area. All aerial and ground application equipment must be properly maintained and calibrated using appropriate carriers.- Avoiding spray drift at the application site is the responsibil- ity of the applicator. Aerial Application Methods and Equipment The interaction of many equipment-related and weather- related factors determines the potential for spray drift. The applicator and the grower are responsible for considering all these factors when making decisions. DO NOT apply under circumstances where possible drift to endangered species, unprotected persons, to food, forage, or other plantings that might be damaged, or crops thereof rendered unfit for sale, use or consumption can occur. DO NOT release spray at a height greater than 10 feet above the crop canopy unless a greater height is required for aircraft safety. The following drift management requirements must be fol- lowed to avoid off-target drift movement from aerial applications to agricultural field crops. These requirements DO NOT apply to forestry applications, public health uses or to applications using dry formulations.

1. The distance of the outermost nozzles on the boom must not exceed 3/4 the length of the fixed wingspan or 90% of the rotor blade diameter.
2. Nozzles must always point backward parallel with the air stream and never be pointed downward more than 45 degrees. Where states have more stringent regulations, they must be observed. Information on Droplet Size The most effective way to reduce drift potential is to apply large droplets. Use the largest droplet size consistent with acceptable efficacy. Applying larger droplets reduces drift potential but will not prevent drift if applications are made improperly or under unfavorable environmental conditions (see Wind; Temperature and Humidity; and Temperature Inversions). Controlling droplet size: • Volume - Use high flow rate nozzles to apply the highest practical spray volume. Nozzles with higher rated flows produce larger droplets. • Pressure - DO NOT exceed the nozzle manufacturer's recommended pressures. For many nozzle types, lower pressure produces larger droplets. When higher flow rates are needed, use higher flow rate nozzles instead of increasing pressure. • Number of Nozzles - Use the minimum number of noz- zles that provide uniform coverage. • Nozzle Orientation - Orienting nozzles so that the spray is released parallel to the air stream produces larger droplets than other orientations and is recommended

practice. Significant deflection from the horizontal will reduce droplet size and increase drift potential. • Nozzle Type - Use a nozzle type that is designed for the intended application. With most nozzle types, narrower spray angles produce larger droplets. Consider using low-drift nozzles. Solid-stream nozzles oriented straight back produce the largest droplets and the lowest drift. Wind DO NOT apply at wind speeds greater than 15 mph. Drift potential is lowest when wind speed does not exceed 10 mph. However, many factors, including droplet size and equipment type, determine drift potential at any given speed. Avoid applications below 2 mph due to variable wind direc- tion and high inversion potential. Local terrain can influence wind patterns. Every applicator must be familiar with local wind patterns and how they affect spray drift. Temperature and Humidity Low humidity and high temperatures increase the evapora- tion of spray droplets and, therefore, the likelihood of increased spray drift. Avoid spraying during conditions of low humidity and/or high temperatures. When making applications in low relative humidity, set up equipment to produce larger droplets to compensate for evaporation. Droplet evaporation is most severe when conditions are both hot and dry. Temperature Inversions Applications must not occur during a temperature inversion because drift potential is high. Temperature inversions restrict vertical air mixing, which causes small suspended droplets to remain in a concentrated cloud. This cloud can move in unpredictable directions due to the light, variable winds common during inversions. Temperature inversions are characterized by increasing temperatures with altitude and are common on nights with limited cloud cover and light-to-no wind. They begin to form as the sun sets and often continue into the morning. Their presence can be indicated by ground fog; however, if fog is not present, inversions can also be identified by the movement of smoke from a ground source or an aircraft smoke genera- tor. Smoke that layers and moves laterally in a concentrated cloud (under low wind conditions) indicates an inversion, while smoke that moves upward and rapidly dissipates indicates good vertical air mixing. Sensitive Areas Only apply the pesticide when the potential for drift to adja- cent sensitive areas (e.g. bodies of water or nontarget crops) is minimal and when wind is blowing away from the sensitive areas. Additives and General Tank Mixing Information Under some conditions, the use of additives or adjuvants may improve the performance of Multiva™ fungicide. However, under some conditions, the use of additives or adjuvants with Multiva can cause adverse phytotoxicity. The addition of a nitrogen-based fertilizer may result in some crop leaf .burn from the fertilizer. The addition of an emulsifiable concentrate (EC)-based insecticide can result in some crop leaf burn. DO NOT tank mix with products containing a prohibition against tank mixing. Follow the most restrictive labeling requirements of any tank mix product. Multiva can be tank mixed with most recommended fungi- cides. However, all varieties and cultivars have not been tested with possible tank mix combinations. Local condi- tions can also influence crop tolerance and may not match those under which BASF has conducted testing. Physical incompatibility, reduced disease control, or crop injury may result from mixing Multiva with other products. Therefore, before using any tank mix (fungicides, insecticides, herbicides, liquid fertilizers, biological control products, adjuvants and additives), test the combination on a small portion of the crop to be treated to ensure that a phyto- toxic response will not occur as a result of application. Consult a BASF representative or local agricultural authori- ties for more information concerning additives. When an adjuvant is to be used with this product, BASF recommends the use of a Chemical Producers and Distributors Association certified adjuvant. Mixing Order

1. Water - Begin by agitating a thoroughly clean sprayer tank 3/4 full of clean water.
2. Agitation - Maintain constant agitation throughout mix- ing and application.
3. Inductor - If an inductor is used, rinse it thoroughly after each component has been added.
4. Products in PVA bags - Place any product contained in water-soluble PVA bags into the mixing tank. Wait until all water-soluble PVA bags have fully dissolved and the product is evenly mixed in the spray tank before continuing.
5. Water-dispersible products (such as Multiva, dry flowables, wettable powders, suspension concentrates, or suspo-emulsions)
6. Water-soluble products
7. Emulsifiable concentrates (or oil concentrates when applicable)
8. Water-soluble additives (such as ammonium sulfate (AMS) or urea ammonium nitrate (UAN) when applicable)
9. Remaining quantity of water Make sure that each component is thoroughly mixed and suspended before adding tank mix partners. Maintain con- stant agitation during application. See Table 2. Multiva™ fungicide Crop-specific Requirements for more details. 8

Restrictions and Limitations - All Crops • DO NOT use less than 5 gallons per acre (gpa) spray vol- ume for ground applications. • For aerial applications, DO NOT use less than 2 gallons per acre (gpa) spray volume on barley, oats, rye, soy- bean, and sugarcane. DO NOT use less than 5 gallons per acre (gpa) spray volume on cotton and sugar beets. DO NOT use less than 1 gallon per acre (gpa) on corn, triticale, and wheat. • DO NOT exceed the maximum product rate (fl ozs/A) per year (season), the maximum product rate per application, or the total number of applications of Multiva™ fungi- cide per year (season) as stated in Table 1. Multiva™ fungicide Restrictions and Limitations Overview and Table 2. Multiva™ fungicide Crop-specific Requirements. Preharvest interval (PHI) restrictions are also included in these tables. • DO NOT apply more than the maximum annual use rate of ai/acre or fl ozs of product/acre for each specific crop from any combination of products containing pyra- clostrobin or metconazole. To determine Ibs of pyraclostrobin per acre, divide fl ozs of product/acre by 128, then multiply by 1.083. To determine Ibs of met- conazole per acre, divide fl ozs of product/acre by 128, then multiply by 0.67. • DO NOT use Multiva in greenhouse or transplant production. • Feeding restrictions - See Table 2. Multiva™ fungi- cide Crop-specific Requirements. • For aerial application in New York State, DO NOT apply within 100 feet of aquatic habitats (such as, but not limited to lakes, reservoirs, rivers, streams, marshes, ponds, estuaries, and commercial fish ponds). Crop Rotation Restriction Leafy vegetables and Brassica leafy vegetables can be planted 30 days after the last application. Crops on this label (barley, corn, cotton, oats, rye, soy- bean, sugar beets, sugarcane, triticale, wheat) plus canola, peanuts, and tuberous and corm vegetables subgroup 1C can be planted immediately following the last application. Dry beans, sorghum, and sunflower may be planted with a plant back interval (PBI) of 0-day. All other crops may be planted 120 days after the last application. \6\l
Ground Applications Directed or Banded Sprays The application rates shown in the following tables pertain to both aerial and ground-(broadcast) methods of applica- tion. Multiva may also be applied as a directed or banded spray over the rows or plant beds with alleys or row mid- dles left upsprayed. For such uses, reduce the labeled Multiva rate in proportion to the area actually sprayed. This adjustment is necessary to avoid applying the product at use rates higher than permitted on this label. Use the following formula to determine the broadcast equivalent rate for applying directed or banded sprays: sprayed bed width + unsprayed row middles = total row width sprayed bed width in inches broadcast rateX total row width in inches treated acres band rate field acre EXAMPLE: Directed spray application to 45-inch plant beds separated by 15-inch unsprayed row middles at 12 fl ozs/A label broadcast rate. 45 inches sprayed bed width + 15 inches unsprayed row middles = 60 inches total row width 45 inches sprayed bed width 12 fl ozs Multiva 9 fl ozs Multiva x60 inches total row width treated acres field acre

rTable 1. Multiva™ fungicide Restrictions and Limitations Overview* Crop Barley Oats Rye Triticale Wheat Corn (all types) Cotton*** Soybeans Sugar beets (roots and tops) Sugarcane Minimum Time from Application to Harvest (PHI) days Apply no later than the beginning of flowering (Zadok's 59 or Feekes 10.5). ** 30 30 14 14 Maximum Product Rate per Application (fl ozs/A) 9 13 8.5 9 10 15.5 Maximum Number of Sequential Applications 2 2 2 3 3 2 Maximum Product Rate per Season (fl ozs/A) 18 51 26 27 30 62

• See Table 2. Multiva™ fungicide Crop-specific Requirements for complete directions and exceptions. **See Table 2. Multiva™ fungicide Crop-specific Requirements. *** Not for use in California unless otherwise directed by BASF labeling. Aerial application is permitted for all labeled crops. For aerial application in New York State, DO NOT apply within 100 feet of aquatic habitats (such as, but not limited to lakes, reservoirs, rivers, streams, marshes, ponds, estuaries, and commercial fish ponds). 10

Table 2. Multiva™ fungicide Crop-specific Requirements (tjil Crop Barley Oats Rye Triticale Wheat Target Disease Black point, Kernel blight, Smudge Alternaria spp., Cochliobolus sativus, Helminthosporium spp. Leaf blotch Pyrenophora spp. Net blotch Pyrenophora feres Powdery mildew Erysiphe graminis Rust Puccinia spp. Scald Rhynchosporium secalis Septoria leaf and glume blotch Septoria spp. , Stagonospora spp. Spot blotch Cochliobolus sativus Stripe rust Puccinia striiformis Tan spot Yellow leaf spot Pyrenophora trichostoma Product Use Rate per Application (fl ozs/A) 7 to 9 Maximum Number of Applications per Season* 2 ' Maximum Product Rate per Season** (fl ozs/A) 18 Minimum Time from Application to HsrvGst (PHI) Apply no later than the beginning of flowering (Zadok's 59 or Feekes 10.5). Application Directions (Regular Season Sprays). For optimal disease control, begin Multiva applications prior to disease development. To maximize yields in cereals, it is important to protect the flag leaf. Apply Multiva immediately after flag leaf emergence for optimum results. Use the higher rate and shorter interval when disease pressure is h gh. Rates up to 9 fl ozs/A of Multiva can be used for severe disease pressure. The minimum retreatment interval (RTI) is 6 days after the first application.

• DO NOT make more than 1 regular season spray when an early season spray is applied to barley, triticale, and wheat. ** The maximum product rate per season is 18 fl ozs/A for all applications (early and/or regular sprays). Resistance Management. To limit the potential for development of resistance, DO NOT make more than two (2)' Multiva applications per season. DO NOT harvest barley hay within 14 days of last application. See Application Directions for Early Season Disease Control in barley, triticale, and wheat. (continued) 11

cApplication Directions (Early Season Spray)4 Crop Barley Triticale Wheat Target Disease Septoria leaf Septoria spp., Spot blotch Cochliobolus sativus Tan spot Yellow leaf spot Pyrenophora trichostoma Suppression Only: Leaf blotch Pyrenophora spp. Powdery mildew Erysiphe graminis Stripe rust Puccinia striiformis Product Use Rate per Application (fl ozs/A) 6 to 9
Maximum Number of Applications per Season 1 Maximum Product Rate per Season (fl ozs/A) 9 Minimum Time from Application to Harvest (PHI) Apply no- later than the beginning of flowering (Zadok's 59 or Feekes 10.5). Application Directions for Early Season Disease Control. Apply 6 to 9 fl ozs/A of Multiva either in combination with a herbicide application or when conditions favor disease development prior to flag leaf emergence. When the early season application is used, a second Multiva application (6 to 9 fl ozs/A) may be required to protect the emerged flag leaf. Environmental conditions and disease pressure at the time of flag leaf emergence are factors to determine the Multiva rate for the second application. The minimum retreatment interval (RTI) is 6 days. DO NOT harvest barley hay within 14 days of last'application. The combination of an early season spray plus a second regular season application after flag leaf emergence must not exceed 18 fl ozs/A per season. Crop Tolerance. Under certain environmental conditions, Multiva demonstrates some phytotoxicity when mixed with EC formulated herbicides or insecticides and/or fertilizers. The possibility of phytotoxicity increases if applications are made under cool, cloudy conditions that persist for several days following application. Multiva applications with bro- moxynil containing products can result in phytotoxicity if applied under cool, wet conditions. Specific Use Requirements. Apply Multiva plus herbicide/insecticide tank mixes by air in a minimum of 5 gallons per acre (gpa) total spray volume. If applied by ground, apply a minimum of 10 gpa. Lower gpa applications can increase the risk of phytotoxicity. DO NOT use adjuvants that contain methylated seed oil, crop oil concentrate or crop oil with emulsifier properties. DO NOT apply Multiva if the final spray solution contains fertilizer at a concentration greaterthan 20% on a v/v basis. DO NOT use early season Multiva applications in bromoxynil based herbicide tank mixes in barley. *Early season disease control is not registered for use in California. 12

rTable 2. Multiva™ fungicide Crop-specific Requirements (continued) Crop Corn Field corn Pop corn Sweet corn Seed production corn Target Disease Anthracnose Colletotrichum graiminicola Eyespot Kabatiella zeae Gray leaf spot Cercospora zeae-maydis Northern corn leaf blight Exserohilum turcicum Northern corn leaf spot Cochliobolus carbonum Physoderma brown spot Physoderma maydis Rust Puccinia spp. Southern corn leaf blight B/po/aris maydis Southern Rust Puccinia polyspora Yellow leaf blight Phyllosticta maydis Product Use Rate per Application (fl ozs/A) 9 to 13 Maximum Number of Applications per Season 4 Maximum Product Rate per Season (fl ozs/A) 51 Minimum Time from Application to Msm/fkctridf vcoi (PHI) 20 days for field corn grain; field corn stover; pop corn grain; pop corn stover; sweet corn stover 7 days for fi©fci corn forage/silage; popcorn forage; sweet corn forage; sweet corn kernel; seed production corn (all types) Application Directions. For optimal disease control, begin Multiva applications prior to disease development and continue on a 7 to 14 day schedule if conditions for disease development persist. Use the higher rate and shorter inter- val when disease pressure is high. Resistance Management. To limit the potential for development of resistance, DO NOT make more than two (2) sequential Multiva applications before alternating to another fungicide with a different mode of action. (continued) 13

r Table 2. Muttiva™ fungicide Crop-specific Requirements (continued) Crop Cotton* Target Disease Alternaria leaf spot, boll rot Alternaria spp. Anthracnose, boll rot Glomerella spp. Ascochyta blight, boll rot Ascochyta gossypii Cercospora blight and leaf spot Cercospora spp. Diplodia boll rot Diplopia spp. Hard lock, boll rot Fusarium spp. Phoma blight, boil rot Phoma spp. Rust Puccinia spp., Phykopsora spp. Stemphyllium leaf spot Stemphyllium spp. Corynespora leaf spot Corynespora cassiicola Product Use Rate per Application (fl ozs/A) 7 to 8.5 10 to 12 Maximum Number of Applications per Season 3 2 Maximum Product Rate per Season (fl ozs/A) 26 24 Minimum Time from Application to Harvp^t1 lul VCOl (PHI) days 30 30 Application Directions. For optimal disease control, begin Multiva applications prior to disease development and continue on a 7 to 14 day schedule if conditions are conducive for disease development. Use the higher rate and short- er interval when disease pressure is high. No livestock feeding restrictions. Resistance Management. To limit the potential for development of resistance, DO NOT make more than two (2) sequential Multiva applications before alternating to another fungicide with a different mode of action.

• Not for use in California unless otherwise directed by BASF labeling. (continued) 14

rTable 2. Multiva™ fungicide Crop-specific Requirements (continued) Crop Target Disease Product Use Rate per Application (fl ozs/A) Maximum Number of Applications per Season Maximum Product Rate per Season (fl ozs/A) Minimum Time from Application to Harvest (PHI) days Soybeans Glycine max Aiternaria leaf spot Alternaria spp. Anthracnose Colletotrichum truncatum Asian soybean rust Phakopsora pachyrhizi Brown spot Septoria glyclnes Frogeye leaf spot Cercospora sojina Pod and stem blight Diaporthe phaseolorum Rhizoctonia aerial blight Rhizoctonia solani 7 to 9 27 30 Suppression Only: Cercospora blight Cercospora kikuchii Application Directions. Multiva can be applied from vegetative through full seed (R6 stage) soybeans. Multiva pro- vides preventive and curative control of soybean rust. For optimal soybean rust control, make initial Multiva application between early flowering and podset (R1 to R3 growth stage) or prior to rust development. If environmental conditions favor continued rust development or if monitoring shows active rust symptoms, repeat application 14 to 21 days after the first application. Use the higher rate and shorter interval when rust pressure is high. For optimal control of other soybean diseases listed above and optimal plant health, apply Multiva between full-flower and pod-set stage (R2 to R4 growth stage) or prior to disease development. DO NOT use adjuvants or tank mix with products with high adjuvant load (see Application Instructions). Soybean forage can be fed no sooner than 14 days after last application. Soybean hay can be fed no sooner than 21 days after last treatment with Multiva. Resistance Management. To limit the potential for development of resistance, DO NOT make more than three (3) Multiva applications per season. (continued) 15

Table 2. Multiva™ fungicide Crop-specific Requirements (continued) Crop Sugar beets (roots and tops) Target Disease Cercospora leaf spot Cercospora beticola Powdery mildew Erysiphe betae Product Use Rate per Application (fl ozs/A) 7 to 10 Maximum Number of Applications per Season 3 Maximum Product Rate per Season (fl ozs/A) 30 Minimum Time from Application to Harvest (PHI) days 14 Application Directions. Begin applications prior to disease development. Apply Multiva at 14 day intervals. Use the higher rate when disease pressure is high. DO NOT use silicone-containing adjuvants with this product. No livestock feeding restrictions. Resistance Management. To limit the potential for development of resistance, DO NOT make more than three (3) Multiva applications per season. Crop Sugarcane Target Disease Brown rust Puccinia melanocephala Orange rust Puccinia kuehnii Product Use Rate per Application (fl ozs/A) 12 to 15.5 Maximum Number of Applications per Season 4 Maximum Product Rate per Season (fl ozs/A) 62 Minimum Time from Application to Harvest (PHI) days 14 Application Directions. For optimal disease control, begin applications of Multiva prior to disease development and continue on a 14 to 28 day interval if conditions are conducive for disease development. Use the higher rate and shorter interval when disease pressure is high. Resistance Management. To limit the potential for development of resistance, DO NOT apply more than 62 fl ozs of Multiva per acre per season. DO NOT make more than two (2) sequential applications of Multiva before alternating to a labeled non Group 11 or non Group 3 fungicide with a different mode of action. 16

r rConditions of Sale and Warranty The Directions For Use of this product reflect the opinion of experts based on field use and tests. The directions are believed to be reliable and must be followed carefully. However, it is impossible to eliminate all risks inherently associated with the use of this product. Crop injury, ineffectiveness or other unintended consequences may result because of such factors as weather conditions, presence of other materials, or use of the product in a manner inconsistent with its labeling, all of which are beyond the control of BASF CORPORATION ("BASF") or the Seller. To the extent consistent with applicable law, all such risks shall be assumed by the Buyer. BASF warrants that this product conforms to the chemical description on the label and is reasonably fit for the purposes referred to in the Directions For Use, subject to the inherent risks, referred to above. TO THE EXTENT CONSISTENT WITH APPLICABLE LAW, BASF MAKES NO OTHER EXPRESS OR IMPLIED WARRANTY OF FITNESS OR MERCHANTABILITY OR ANY OTHER EXPRESS OR IMPLIED WARRANTY. TO THE EXTENT CONSISTENT WITH APPLICABLE LAW, BUYER'S EXCLUSIVE REMEDY AND BASF'S EXCLUSIVE LIABILITY, WHETHER IN CONTRACT, TORT, NEGLIGENCE, STRICT LIABILITY, OR OTHERWISE, SHALL BE LIMITED TO REPAYMENT OF THE PURCHASE PRICE OF THE PRODUCT. TO THE EXTENT CONSISTENT WITH APPLICABLE LAW, BASF AND THE SELLER DISCLAIM ANY LIABILITY FOR CONSEQUENTIAL, EXEMPLARY, SPECIAL OR INDIRECT DAMAGES RESULTING FROM THE USE OR HANDLING OF THIS PRODUCT. BASF and the Seller offer this product, and the Buyer and User accept it, subject to the foregoing Conditions of Sale and Warranty which may be varied only by agreement in writing signed by a duly authorized representative of BASF. nos Multiva is a trademark of BASF Corporation. © 2013 BASF Corporation All rights reserved. 007969-00247.20130628C.NVA 2013-04-268-0121 Supersedes: NVA 2013-04-268-0046 Supplemental: NVA 2012-04-268-0066 BASF Corporation 26 Davis Drive Research Triangle Park, NC 27709 El BASFThe Chemical Company 17

ACCEBTFD SEPOV" Undor Ito fW««i l
tA.-". j "§V''V ' J-} • f i'"'^^m'"^5^^^^^'^A^^^ i's V"f j?-j--A,'""''" - ui1 * ^ '""Jft^ 1 ~a£££f3Sf-gf- ' * "^f^^^- Vft-tf ft »r~V "•'•> '•- i it\¥fc4Ci<^/f^;^ n sfVfHJ'dK^.i .'t -' . °C"-'J SK^iiiSI&iti'(i.illii - Label K-§? Group Fungicide Multiva™ fungicide For disease control and plant health in sugarcane This supplemental label expires December 31, 2015 and must not be used or distributed after this date. Active Ingredient: pyraclostrobin: (carbamic acid, [2-[[[1-(4-chlorophenyl)-1H-pyrazol- 3-yl]oxy]methyl]phenyl]methoxy-,methyl ester) : , 12.0% metconazole*: 5-[(4-chlorophenyl)methyl]-2,2-dimethyl-1- (1/-/-1,2,4-triazol-1-ylmethyl)cyclopentanol 7.4% Other Ingredients***: .• 80.6% Total: •. 100.0%

• Equivalent to 1.083 pounds of pyraclostrobin per gallon ** Equivalent to 0.67 pound of metconazole per gallon *** Contains petroleum distillates EPA Reg. No. 7969-247 Environmental Hazards This pesticide is toxic to birds, mammals, fish and aquatic invertebrates. Drift or runoff may be hazardous to aquatic organisms in water adjacent to treated areas. DO NOT apply directly to water, or to areas where surface water is present, or to intertidal areas below the mean high water mark. DO NOT contaminate water when disposing of equipment wash water or rinsate. Groundwater Advisory This chemical has properties and characteristics associated with chemicals detected in groundwater. The use of this chemical in areas where soils are permeable, particularly where the water table is shallow, may result in groundwater contamination. Surface Water Advisory Metconazole and pyraclostrobin may impact surface water quality through spray and runoff of rain water. This product has a high potential for runoff for several months or more after application. Poorly draining soils or soils with shallow water tables are more prone to produce runoff that contains this product. A level, well- maintained vegetative buffer strip between areas towhich this product is applied and surface water features, such as ponds, streams, and springs, will reduce the potential for contamination of water from BASF Corporation 26 Davis Drive, Research Triangle Park, NC 27709 rainfall runoff. Runoff of this product will be reduced by avoiding applications when rainfall is forecast to occur within 48 hours. Directions For Use • It is a violation of federal law to use this product in a manner inconsistent with its labeling. • The supplemental labeling and the entire Multiva™ fungicide container label, EPA Reg. No. 7969-247, must be in possession of the user at the time of application. • Read the label affixed to the container for Multiva before applying. • Use of Multiva according to this labeling is subject to the use precautions and limitations imposed by the label affixed to the container for Multiva. Application Instructions Multiva may be applied to sugarcane when used according to the instructions on this supplemental. Refer to the Multiva main label for additional application instructions and restrictions. D•BASFThe Chemical Company

Table 1. Multiva™ fungicide Restrictions and Limitations Overview Crop Sugarcane Minimum Time from Application to Harvest (PHI) (days) 14 Maximum Product Rate per Application (fl ozs/A) 15.5 Maximum Number of Sequential Applications 2 Maximum Product Rate per Season (fl ozs/A) 62 Table 2. Multiva Crop-specific Requirements Crop Target Disease Product Use Rate per Application (fl ozs/A) Maximum Number of Applications per Season Maximum Product Rate per Season (fl ozs/A) Minimum Time from Application to Harvest (PHI) (days) Sugarcane Brown Rust Puccinia melanocephala Orange Rust Puccinia kuehnii 12 to 15.5 62 14 Application Directions. For optimal disease control, begin applications of Multiva prior to disease development and continue on a 14 to 28 day interval if conditions are conducive for disease development. Use the higher rate and shorter interval when disease pressure is high. Resistance Management. To limit the potential for development of resistance, DO NOT apply more than 62 fl ozs of Multiva per acre per season. DO NOT make more than two (2) sequential applications of Multiva before alternating to a labeled non Group 11 or non Group 3 fungicide with a different mode of action.

7.1 Conditions of Sale and Warranty The Directions For Use of this product reflect the opinion of experts based on field use and tests. The directions are believed to be reliable and must be followed carefully. However, it is impossible to eliminate all risks inherently associated with the use of this product. Crop injury, ineffectiveness or other unintended consequences may result because of such factors as weather conditions, presence of other materials, or use of the product in a manner inconsistent with its labeling, all of which are beyond the control of BASF CORPORATION ("BASF") or the Seller. To the extent consistent with applicable law, all such risks shall be assumed by the Buyer. BASF warrants that this product conforms to the chemical description on the label and is reasonably fit for the purposes referred to in the Directions For Use, subject to the inherent risks, referred to above. TO THE EXTENT CONSISTENT WITH APPLICABLE LAW, BASF MAKES NO OTHER EXPRESS OR IMPLIED WARRANTY OF FITNESS OR MERCHANTABILITY OR ANY OTHER EXPRESS OR IMPLIED WARRANTY. TO THE EXTENT CONSISTENT WITH APPLICABLE LAW, BUYER'S EXCLUSIVE REMEDY AND BASF'S EXCLUSIVE LIABILITY, WHETHER IN CONTRACT, TORT, NEGLIGENCE, STRICT LIABILITY, OR OTHERWISE, SHALL BE LIMITED TO REPAYMENT OF THE PURCHASE PRICE OF THE PRODUCT. TO THE EXTENT CONSISTENT WITH APPLICABLE LAW, BASF AND THE SELLER DISCLAIM ANY LIABILITY FOR CONSEQUENTIAL, EXEMPLARY, SPECIAL OR INDIRECT DAMAGES RESULTING FROM THE USE OR HANDLING OF THIS PRODUCT. BASF and the Seller offer this product, and the Buyer and User accept it, subject to the foregoing Conditions of Sale and Warranty which may be varied only by agreement in writing signed by a duly authorized representative of BASF. nos Multiva is a trademark of BASF. ©2013 BASF Corporation All rights reserved. 007969-00247.20120425b. NVA 2011 -04-268-0066 BASF Corporation 26 Davis Drive Research Triangle Park, NC 27709 BASFThe Chemical Company