crop-chem-docs/corpus/epa_ppls/7969-156.md

OUTLOOK HERBICIDE

• EPA Reg No: 7969-156
• Registrant: BASF AGRICULTURAL SOLUTIONS US, LLC
• Signal word: Warning
• Active ingredients: dimethenamid-P (63.9%)
• Label accepted: 2019-11-29
• Source PDF: https://www3.epa.gov/pesticides/chem_search/ppls/007969-00156-20191129.pdf

---

UNITED STATES ENVIRONMENTAL PROTECTION AGENCY WASHINGTON, DC 20460

PRIA Non-New-Use Label Acceptable v.20150320 OFFICE OF CHEMICAL SAFETY AND POLLUTION PREVENTION November 29, 2019

Craig Kleppe Agricultural Products Division BASF Corporation 26 Davis Drive P.O. Box 13528 Research Triangle Park, NC 27709-3528

Subject: PRIA Label Amendment – Amending use pattern to delete the preemergence application timing and shift to early postemergence. Product Name: Outlook Herbicide EPA Registration Number: 7969-156 Application Date: November 2, 2018 Decision Number: 545851

Dear Mr. Kleppe:

The amended label referred to above, submitted in connection with registration under the Federal Insecticide, Fungicide and Rodenticide Act, as amended, is acceptable. This approval does not affect any conditions that were previously imposed on this registration. You continue to be subject to existing conditions on your registration and any deadlines connected with them.

A stamped copy of your labeling is enclosed for your records. This labeling supersedes all previously accepted labeling. The next label printing of this product must use this labeling unless subsequent changes have been approved. You must submit one copy of the final printed labeling before you release the product for shipment with the new labeling. In accordance with 40 CFR 152.130(c), you may distribute or sell this product under the previously approved labeling for 18 months from the date of this letter. After 18 months, you may only distribute or sell this product if it bears this new revised labeling or subsequently approved labeling. “To distribute or sell” is defined under FIFRA section 2(gg) and its implementing regulation at 40 CFR 152.3.

Should you wish to add/retain a reference to the company’s website on your label, then please be aware that the website becomes labeling under the Federal Insecticide Fungicide and Rodenticide Act and is subject to review by the Agency. If the website is false or misleading, the product would be misbranded and unlawful to sell or distribute under FIFRA section 12(a)(1)(E). 40 CFR 156.10(a)(5) list examples of statements EPA may consider false or misleading. In addition, regardless of whether a website is referenced on your product’s label, claims made on the website may not substantially differ from those claims approved through the registration process. Therefore, should the Agency find or if it is brought to our attention that a website contains false or misleading statements or claims substantially differing from the EPA approved registration, the website will be referred to the EPA’s Office of Enforcement and Compliance.

Page 2 of 2 EPA Reg. No. 7969-156 Decision No. 545851

Your release for shipment of the product constitutes acceptance of these conditions. If these conditions are not complied with, the registration will be subject to cancellation in accordance with FIFRA section 6. If you have any questions, please contact Julia Kerr by phone at 703-347- 0386, or via email at kerr.julia@epa.gov.

Enclosure

Sincerely,

Emily Schmid, Product Manager 25 Herbicide Branch Registration Division (7505P) Office of Pesticide Pro grams

A selective residual herbicide for use in certain agricultural crops Active Ingredient*: dimethenamid-P: (S)-2-chloro-N-[(1-methyl-2-methoxy)ethyl]- N-(2,4-dimethyl-thien-3-yl)-acetamide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63.9% Other Ingredients**: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36.1% Total: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100.0%

• Contains 6.0 pounds of active ingredient per gallon ** Contains petroleum distillates EPA Reg. No. 7969-156 EPA Est. No. KEEP OUT OF REACH OF CHILDREN WARNING/AVISO See inside for complete First Aid, Precautionary Statements, Directions For Use, Conditions of Sale and Warranty, and state-specific crop and/or use site restrictions. In case of an emergency endangering life or property involving this product, call day or night 1-800-832-HELP (4357). Net Contents: BASF Corporation 26 Davis Drive, Research Triangle Park, NC 27709 Si usted no entiende la etiqueta, busque a alguien para que se la explique a usted en detalle. (If you do not understand the label, find someone to explain it to you in detail.) Dimethenamid-P Group 15 Herbicide 11/29/2019 7969-156

2 Precautionary Statements Hazards to Humans and Domestic Animals WARNING. Causes substantial but temporary eye injury. Harmful if inhaled, swallowed, or absorbed through the skin. DO NOT get in eyes or on clothing. Avoid contact with skin. Avoid breathing spray mist. Prolonged or frequently repeated skin contact may cause allergic reactions in some individuals. Wash hands thoroughly with soap and water after handling and before eating, drinking, chewing gum, using tobacco, or using the toilet. Remove and wash con- taminated clothing before reuse. Personal Protective Equipment (PPE) Applicators and other handlers must wear: • Long-sleeved shirt and long pants • Waterproof gloves • Shoes plus socks • Protective eyewear (goggles or a face shield) User Safety Requirements Discard clothing and other absorbent materials that have been drenched or heavily contaminated with this product’s concentrate. DO NOT reuse them. Follow the manufac - turer’s instructions for cleaning and maintaining PPE. If no such instructions for washables exist, use detergent and hot water. Keep and wash PPE separately from other laundry. Engineering Controls When handlers use closed systems, enclosed cabs, or air- craft in a manner that meets the requirements listed in the Worker Protection Standard (WPS) for agricultural pesticides [40 CFR 170.240(d)(4-6)], the handler PPE requirements may be reduced or modified as specified in the WPS. IMPORTANT:When reduced PPE is worn because a closed system is being used, handlers must be provided all PPE specified above for applicators and other handlers and have such PPE immediately for use in an emergency, such as a spill or equipment breakdown. Mixers and loaders for aerial applications must use a closed system that meets the requirements listed in the Worker Protection Standard (WPS) for Agricultural Pesticides [40 CFR 170.240 (d)(4)] for dermal protection, and must: • Wear personal protective equipment (PPE) required in the PPE section of this labeling for applicators and other handlers • Wear protective eyewear, if the system operates under pressure • Either use a closed system that also meets the require- ments in the WPS for inhalation protection or wear a NIOSH-approved dust-mist respirator with a TC84 cartridge • Be provided and have immediately available for use in an emergency, such as a spill or equipment breakdown: coveralls, chemical-resistant footwear, and dust-mist respirator, or if using a closed system cab that provides respiratory protection, a NIOSH-approved dust-mist respirator with a TC84 cartridge FIRST AID If in eyes • Hold eyes open and rinse slowly and gently with water for 15 to 20 minutes. • Remove contact lenses, if present, after the first 5 minutes; then continue rinsing eyes. • Call a poison control center for treatment advice. If swallowed • Call a poison control center or doctor immediately for treatment advice. • DO NOT induce vomiting unless told to do so by a poison control center or doctor. • DO NOT give any liquid to the person. • DO NOT give anything by mouth to an unconscious person. If on skin or clothing • Take off contaminated clothing. • Rinse skin immediately with plenty of water for 15 to 20 minutes. • Call a poison control center or doctor for treatment advice. If inhaled • Move person to fresh air. • If person is not breathing, call 911 or an ambulance; then give artificial respiration, preferably by mouth to mouth, if possible. • Call a poison control center or doctor for further treatment advice. HOTLINE NUMBER Have the product container or label with you when calling a poison control center or doctor or going for treatment. You may also contact BASF Corporation for emergency medical treatment information: 1-800-832-HELP (4357). Note to Physician: Contains petroleum distillate. Vomiting may cause aspiration pneumonia.

3 Environmental Hazards DO NOT apply directly to water, areas where surface water is present, or intertidal areas below the mean high water mark. DO NOT contaminate water when disposing of equipment washwater or rinsate. Dimethenamid-P has properties that may result in ground- water contamination. Application in areas where soils are permeable or coarse and groundwater is near the surface could result in groundwater contamination. Dimethenamid-P has properties that may result in surface water contamination via dissolved runoff and runoff erosion. Practices should be followed to minimize the potential for dissolved runoff and/or runoff erosion. Point-source Contamination. To prevent point-source contamination, DO NOT mix or load this or any other pes- ticide product within 50 feet of wells (including abandoned wells and drainage wells), sinkholes, perennial or intermit- tent streams and rivers, and natural or impounded lakes and reservoirs. This setback does not apply to properly capped or plugged abandoned wells and does not apply to impervious pad or dike mixing/loading areas as described below. Mixing, loading, rinsing, or washing operations performed within 50 feet of a well are allowed only when conducted on an impervious pad constructed to withstand the weight of the heaviest load that may be on or move across the pad. The pad must be self-contained to prevent surface water flow over or from the pad. The pad capacity must be maintained at 110% that of the largest pesticide container or application equipment used on the pad and have suffi- cient capacity to contain all product spills, equipment or container leaks, equipment washwater, and rainwater that may fall on the pad. The containment capacity does not apply to vehicles delivering pesticide shipments to the mixing/loading site. States may have in effect additional requirements regarding wellhead setbacks and operational containment. Care must be taken when using this product to prevent: • Back-siphoning into wells • Spills • Improper disposal of excess pesticide, spray mixes, or rinsates Check valves or anti-siphoning devices must be used on all mixing equipment. Movement Dissolved in Runoff or through Soil. DO NOT apply under conditions which favor runoff. DO NOT apply to impervious substrates such as paved or highly compacted surfaces or frozen soils. Groundwater contamination may occur in areas where soils are perme- able or coarse and groundwater is near the surface. To minimize the possibility of groundwater contamination, carefully follow application rate as affected by soil type in the Application Instructions section of this label. DO NOT apply if all three criteria exist: coarse soils classi- fied as sand (does not include loamy sand or sandy loam), less than 3% organic matter (as determined by soil tests, if not known), and where depth to groundwater is 30 feet or less. Movement by Water Erosion of Treated Soil. DO NOT apply or incorporate this product by flood or fur- row irrigation. Ensure treated areas have received at least 0.5 inch of rainfall before using tailwater for subsequent irri- gation of other fields. Endangered Species Protection This product may have effects on federally listed threatened or endangered plant species or their critical habitat. When using this product, you must follow the measures contained in the Endangered Species Protection Bulletin for the county or parish in which you are applying the pesti- cide. To determine if your county or parish has a Bulletin, and to obtain that Bulletin, consult http://www.epa.gov/espp/, or call 1-844-447-3813 no more than 6 months before using this product. Applicators must use Bulletins that are in effect in the month in which the pesticide will be applied. New Bulletins will generally be available from the above sources 6 months before their effective dates. To avoid adverse effects on endangered plant species, applicators must comply with the following mitigation measures when endangered plant species are known to occur in proximity of the application site: • Aerial Application - Leave a 150-foot untreated buffer between treatment area and endangered plant populations. • Ground Application - Use low-pressure nozzles according to the manufacturer’s specifications that pro- duce only medium-to-coarse or very coarse droplets AND leave a 35-foot untreated buffer between treatment area and known endangered plant populations. USER SAFETY RECOMMENDATIONS Users should: • Remove clothing/PPE immediately if pesticide gets inside. Then wash thoroughly and put on clean clothing. • Remove PPE immediately after handling this product. Wash the outside of gloves before removing. As soon as possible, wash thoroughly and change into clean clothing.

4 Directions For Use It is a violation of federal law to use this product in a man- ner inconsistent with its labeling. DO NOT apply this product in a way that will contact workers or other persons, either directly or through drift. Only protected handlers may be in the area during application. For any requirements specific to your state or tribe, consult the agency responsible for pesticide regulation. Unless otherwise directed in supplemental labeling, follow all applicable directions, restrictions, precautions and Conditions of Sale and Warranty. This labeling must be in the user’s possession during application. (continued) (continued) STORAGE AND DISPOSAL DO NOT contaminate water, food, or feed by storage or disposal. Open dumping is prohibited. Pesticide Storage DO NOT use or store near heat or open flame. Store in original container in a well-ventilated area separately from fertilizer, feed, or foodstuffs and away from other pesticides. Avoid cross-contamination with other pesticides. Groundwater contamination may be reduced by diking and flooring of permanent liquid bulk storage sites with an impermeable material. STORAGE AND DISPOSAL (continued) Pesticide Disposal Wastes resulting from this product must be disposed of on-site or at a waste disposal facility. Improper disposal of excess pesticide, spray mix, or rinsate is a violation of fed- eral law. If these wastes cannot be disposed of according to label instructions, contact the state agency responsible for pesticide regulation or the Hazardous Waste represen- tative at the nearest EPA Regional Office for guidance. Container Handling Nonrefillable Container. DO NOT reuse or refill this container. Triple rinse or pressure rinse container (or equivalent) promptly after emptying; then offer for recycling, if available, or reconditioning, if appropriate, or puncture and dispose of in a sanitary landfill, or by inciner- ation, or by other procedures approved by state and local authorities. Triple rinse containers small enough to shake (capacity /unif0a35 gallons) as follows: Empty the remaining contents into application equipment or a mix tank and drain for 10 seconds after the flow begins to drip. Fill the container 1/4 full with water and recap. Shake for 10 sec- onds. Pour rinsate into application equipment or a mix tank, or store rinsate for later use or disposal. Drain for 10 seconds after the flow begins to drip. Repeat this pro- cedure two more times. Triple rinse containers too large to shake (capacity > 5 gallons) as follows: Empty the remaining contents into application equipment or a mix tank. Fill the container 1/4 full with water. Replace and tighten closures. Tip container on its side and roll it back and forth, ensuring at least one complete revolution, for 30 seconds. Stand the container on its end and tip it back and forth several times. Turn the container over onto its other end and tip it back and forth several times. Empty the rinsate into application equipment or a mix tank, or store rinsate for later use or disposal. Repeat this proce- dure two more times. Pressure rinse as follows: Empty the remaining contents into application equipment or mix tank and con- tinue to drain for 10 seconds after the flow begins to drip. Hold container upside down over application equipment or mix tank, or collect rinsate for later use or disposal. Insert pressure rinsing nozzle in the side of the container and rinse at about 40 PSI for at least 30 seconds. Drain for 10 seconds after the flow begins to drip. Refillable Container. Refill this container with pesticide only. DO NOT reuse this container for any other purpose. Triple rinsing the container before final disposal is the responsibility of the person disposing of the container. Cleaning before refilling is the responsibility of the refiller. AGRICULTURAL USE REQUIREMENTS Use this product only in accordance with its labeling and with the Worker Protection Standard, 40 CFR Part 170. This standard contains requirements for the protection of agricultural workers on farms, forests, nurseries, and greenhouses, and handlers of agricultural pesticides. It contains requirements for training, decontamination, notifi- cation, and emergency assistance. It also contains specific instructions and exceptions pertaining to the statements on this label about personal protective equip- ment (PPE) and restricted-entry interval. The requirements in this box only apply to uses of this product that are cov- ered by the Worker Protection Standard. DO NOT enter or allow worker entry into treated areas during the restricted-entry interval (REI) of 12 hours. EXCEPTION: If the product is soil injected or soil incor- porated, the Worker Protection Standard, under certain circumstances, allows workers to enter the treated area if there will be no contact with anything that has been treated. PPE required for early entry to treated areas that is permit- ted under the Worker Protection Standard and that involves contact with anything that has been treated, such as plants, soil, or water, is: • Coveralls • Waterproof gloves • Shoes plus socks • Protective eyewear (goggles or a face shield)

5 In Case of Emergency In case of large-scale spill of this product, call: • CHEMTREC 1-800-424-9300 • BASF Corporation 1-800-832-HELP (4357) In case of medical emergency regarding this product, call: • Your local doctor for immediate treatment • Your local poison control center (hospital) • BASF Corporation 1-800-832-HELP (4357) Steps to take if material is released or spilled: • Dike and contain the spill with inert material (sand, earth, etc.) and transfer liquid and solid diking material to sepa- rate containers for disposal. • Remove contaminated clothing, and wash affected skin areas with soap and water. • Wash clothing before reuse. • Keep the spill out of all sewers and open bodies of water. Product Information Outlook® herbicide is a selective residual herbicide for controlling many annual grass weeds, annual broadleaf weeds, and sedge as they germinate (see Table 1). Outlook can be used in agricultural field and row crops including bean (dry), beets [sugar, table (garden)], corn [field corn (grain, seed, silage), fresh sweet corn, pop- corn], cotton, fallow, garlic, hops, horseradish, onions (dry bulb, green), peanut, perennial grasses grown for seed, potato, pumpkin, radish, rutabaga, shallots (dry bulb), sorghum (grain), soybean, sweet potato, tuberous and corm vegetables, turnip, and winter squash. Table 1. Weeds Controlled (continued) Common Name Scientific Name Annual Grass Weeds Barnyardgrass Echinochloa crus-galli Bluegrass, annual Poa annua Bluegrass, roughstalk Poa trivialis Brome, California Bromus carinatus Brome, downy Bromus tectorum Crabgrass, large Digitaria sanguinalis Crabgrass, smooth Digitaria ischaemum Cupgrass, Southwestern Eriochloa gracilis Cupgrass, woolly1 Eriochloa villosa Fescue, rattail Vulpia myuros Foxtail, giant Setaria faberi Foxtail, green Setaria viridis Foxtail, yellow Setaria glauca Goosegrass Eleusine indica Johnsongrass (seedling)1 Sorghum halepense Millet, wild proso1 Panicum miliaceum Panicum, fall Panicum dichotomiflorum Panicum, Texas1 Panicum texanum Red rice Oryza sativa Ryegrass, Italian Lolium multiflorum Sandbur1 Cenchrus spp. Shattercane1 Sorghum bicolor Signalgrass, broadleaf1 Brachiaria platyphylla Witchgrass Panicum capillare STORAGE AND DISPOSAL (continued) Container Handling (continued) Triple rinse as follows: To clean the container before final disposal, empty the remaining contents from this container into application equipment or mix tank. Fill the container about 10% full with water. Agitate vigorously or recirculate water with the pump for 2 minutes. Pour or pump rinsate into application equipment or rinsate collec- tion system. Repeat this rinsing procedure two more times. When this container is empty, replace the cap and seal all openings that have been opened during use; return the container to the point of purchase or to a designated lo - cation. This container must only be refilled with a pesticide product. Prior to refilling, inspect carefully for damage such as cracks, punctures, abrasions, worn-out threads and closure devices. Check for leaks after refilling and before transport. DO NOT transport if this container is damaged or leaking. If the container is damaged, or leak- ing, or obsolete and not returned to the point of purchase or to a designated location, triple rinse emptied container and offer for recycling, if available, or dispose of container in compliance with state and local regulations.

6 Table 1. Weeds Controlled (continued) Mode of Action Dimethenamid-P , the active ingredient in Outlook, is a Group 15 (WSSA) Group K3 (HRAC) herbicide belonging to the chloroacetamide chemistry class. Outlook is a root- and-shoot growth inhibitor that controls susceptible germinating seedlings before or soon after they emerge from the soil. Herbicide Resistance Management Outlook is a Group 15/Group K3 herbicide. Any weed pop ulation may contain or develop plants naturally resistant to Outlook and other Group 15 herbicides. Weed species with resistance to Group 15 may eventually dominate the weed population if Group 15 herbicides are used repeat- edly in the same field or in successive years as the primary meth od of control for targeted species. This may result in partial or total loss of control of those species by Outlook or other Group 15 herbicides. To delay herbicide resistance consider: • Avoiding the consecutive use of Outlook or other target- site-of-action Group 15 herbicides that have a similar target site of action on the same weed species. • Using tank mixes or premixes with herbicides from differ- ent target-site-of-action groups as long as the involved products are all registered for the same use, have differ- ent sites of action, and are both effective at the tank mix or prepack rate on the weed(s) of concern. • Basing herbicide use on a comprehensive IPM (Integrated Pest Management) program including cultural and mechanical methods. • Monitoring treated weed populations for loss of field effi- cacy, and control of escapes with effective alternative herbicides or mechanical methods. • Identify weeds present in the field through scouting and field history and understand their biology. The weed- control program needs to consider all of the weeds present. • Scout fields prior to application to identify the weed species present and their growth stage to determine if the intended application will be effective. • Scout fields after application to verify the treatment was effective. • Suspected herbicide-resistance weeds may be identified by these indicators:

1. Failure to control a weed species normally controlled by the herbicide at the dose applied, especially if con- trol is achieved on adjacent weeds;
2. A spreading patch of non-controlled plants of a partic- ular weed species; and
3. Surviving plants mixed with controlled individuals of the same species. • If resistance is suspected, treat weed escapes with an herbicide with a different MOA and/or use non-chemical methods to remove escapes, as practical, with the goal of preventing further seed production. • Report any incidence of non-performance of this product against a particular weed species to your local BASF representative. • Contacting your local extension specialist, certified crop advisors, and/or manufacturer for herbicide resistance management and/or integrated weed management direc- tions for specific crops and resistant weed biotypes. Application Instructions Outlook provides most effective weed control when applied by ground or aerial equipment and subsequently incorporated into soil by rainfall, sprinkler irrigation, or mechanical tillage before weed seedling emergence from soil. Outlook can also be applied through chemigation. Outlook may be applied as a preplant incorporated, preplant surface, preemergence, early postemergence, or Common Name Scientific Name Annual Broadleaf Weeds Amaranth, Palmer Amaranthus palmeri Amaranth, Powell Amaranthus powellii Beggarweed, Florida1 Desmodium tortuosum Carpetweed Mollugo verticillata Chamomile, mayweed Anthemis cotula Eclipta1 Eclipta alba Lambsquarters, common1 Chenopodium album Nightshade, black2 Solanum nigrum Nightshade, cutleaf2 Solanum triflorum Nightshade, Eastern black2 Solanum ptycanthum Nightshade, hairy2 Solanum sarrachoides Pigweed, prostrate Amaranthus blitoides Pigweed, redroot Amaranthus retroflexus Pigweed, smooth Amaranthus hybridus Pigweed, tumble Amaranthus albus Purslane, common Portulaca oleracea Pusley, Florida Richardia scabra Ragweed, common1 Ambrosia artemisiifolia Spurge, nodding Chamaesyce nutans Spurge, spotted Chamaesyce maculata Waterhemp, common2 Amaranthus rudis Waterhemp, tall2 Amaranthus tuberculatus Sedge Flatsedge, rice Cyperus iria Nutsedge, yellow2 Cyperus esculentus 1 Partial control or suppression only. To complement control, use Outlook® herbicide in tank mixes or sequential application with other herbicides that provide additional control of these weed species. 2 For best control of these species, use the highest rate specified by soil type. If dry conditions exist near application or excessive rainfall occurs early in season, a post emergence herbicide or cultivation may be required to help control these weeds.

7 layby (corn) treatment. Outlook® herbicide may be applied using water or sprayable fluid fertilizer as the spray carrier. Additionally, Outlook may be impregnated on and applied with dry bulk fertilizer. Sprayable fluid fertilizer as a carrier is not advised for use after crop emergence. Refer to Additives for more information. Application Rate Application rates for Outlook when applied alone, in tank mix, or in sequential applications are given in Table 2, and vary by soil texture and organic matter content. Refer to Crop-specific Information for additional rate information. Table 2. Outlook Application Rate/Acre 1,2,3 Soil texture groups used in this label are coarse (sand, loamy sand, sandy loam), medium (silt, silt loam, loam, sandy clay loam), and fine (sandy clay, silty clay, silty clay loam, clay loam, and clay). DO NOT apply on coarse soils classified as sand (does not include loamy sand or sandy loam) with less than 3% organic matter (as determined by soil tests, if not known), and where depth to groundwater is 30 feet or less. When use rates are expressed in ranges, use the lower rate for more coarsely textured soils lower in organic mat- ter; use the higher rate for more finely textured soils high in organic matter. Preplant Incorporated Application Apply Outlook and incorporate into the upper (1 to 2 inch- es) soil surface up to 2 weeks before planting. Use a harrow, rolling cultivator, finishing disk, or other implement capable of giving uniform shallow incorporation. Avoid deeper incorporation or reduced weed control or crop injury may result. Preplant Surface Application For use in minimum tillage or no-till production systems, apply Outlook alone or in tank mixes up to 45 days before planting. When making early preplant application (15 to 45 days before planting), use the highest rate specified for the specific soil type. Early preplant applications are not for use on coarse-texture soils or in areas where average annual rainfall (or rainfall plus irrigation) typically exceeds 40 inches. Early preplant applications may be applied as part of a split application program where the second appli- cation is made after planting (use 2/3 of Outlook rate early followed by 1/3 of rate after planting). A split application is advised when the initial application is made more than 30 days before planting. Tank mixes with postemergence herbicides registered for use on the specific crop such as glyphosate, Touchdown ® herbicide (glyphosate), or Gramoxone Inteon® herbicide (paraquat) must be used when weeds are present at the time of application. Preemergence Surface Application Broadcast treatment uniformly to the soil surface after planting and before crop emergence. Rainfall, sprinkler irrigation, or shallow mechanical incorporation after appli- cation is required to move this product into the upper soil surface where weed seeds germinate. If adequate rainfall or irrigation does not occur and weed seedling emergence begins, a shallow cultivation or rotary hoeing will improve performance. Early Postemergence Application Outlook must be applied before weed seedling emergence or in a tank mix with products registered for use on the specific crop on this label that control the emerged weeds. Refer to Crop-specific Information for specific postemergence applications by crop. Layby Application Use Outlook in field corn, seed corn, and popcorn. See Crop-specific Information - Corn for more details on layby application. Split Application Outlook may be used in split application programs where applications are made as part of the methods described above. If applications are less than 2 weeks apart, the total Outlook rate used must not exceed the maximum rate given for each specific soil type. If applications are 2 weeks or more apart, a total Outlook application rate of up to 21 fl ozs/A per year may be used on any soil type in all labeled crops except corn, cotton, sugar beet, and soybean. See Crop-specific Information section for maximum seasonal application rate in corn, cotton, sugar beet, and soybean. Fall Application For use only in the following states: Iowa, Minnesota, North Dakota, South Dakota, Wisconsin, north of Highway 136 in Illinois, and north of Highway 91 in Nebraska. Outlook may be used in fall applications to control weeds in minimum tillage or no-till corn or soybean production systems planted the following spring. Apply up to 21 fl ozs/A of Outlook to medium-texture and fine-texture soils with greater than 2.5% organic matter. Soil Texture Organic Matter Content Less than 3% (fl ozs) 3% or more (fl ozs) Coarse 12 to 14 14 to 18 Medium 14 to 18 18 to 21 Fine See tank mix descriptions for the specified application rate ranges of other herbicides tank mixed with Outlook. 1 The application rates listed are intended for full-season control of targeted weeds. Reduced application rates (8 to 16 fl ozs/A of Outlook) may be used where partial control or reduced length of soil residual control is required, such as postemergence application, or preemergence application where cultivation or sequentially applied herbicides will be used for added control of the same targeted weed species. Use 8 to 12 fl ozs/A of Outlook on coarse-texture soils. Use 12 to 16 fl ozs/A of Outlook on medium-texture and fine-texture soils. 2 For all early preplant applications, use 21 fl ozs/A of Outlook. 3 On muck soils and high organic matter soils, apply Outlook at 21 fl ozs/A.

8 Fall applications must be made after October 1. Apply Outlook® herbicide in the fall after crop harvest when soil temperature at the 4-inch depth is sustained at less than 55º F and before the ground freezes. Tillage operations may be conducted before or after apply- ing Outlook. If following an application, tillage should be no more than 2 to 3 inches deep to uniformly incorporate the herbicide into the upper soil surface. If a sequential application program (fall application followed by spring application of Outlook) is used, the maximum combined rate of Outlook that may be applied is 21 fl ozs/A per crop season. Spray Drift Management Avoiding spray drift at the application site is the responsibility of the applicator. The interaction of many equipment-related and weather-related factors determines the potential for spray drift. The applicator and the grower are responsible for considering all these factors when making decisions. Where states have more stringent regu- lations, they must be observed. The applicator should be familiar with and take into account the following drift reduc- tion advisory information. Controlling Droplet Size The most effective way to reduce drift potential is to apply large droplets that provide sufficient coverage and control. Applying larger droplets reduces drift potential but will not prevent drift if applications are made improperly or under unfavorable environmental conditions (see Wind; Temperature and Humidity; and Temperature Inversion). • Volume - Use high flow rate nozzles to apply the highest practical spray volume. Nozzles with higher rated flows produce larger droplets. • Pressure - DO NOT exceed the nozzle manufacturer’s specified pressures. For many nozzle types, lower pres- sure produces larger droplets. When higher flow rates are needed, use higher flow rate nozzles instead of increas- ing pressure. • Number of Nozzles - Use the minimum number of noz- zles that provide uniform coverage. • Nozzle Orientation - Orienting nozzles so spray is released parallel to the airstream produces larger droplets than other orientations and is preferred practice. Significant deflection from the horizontal will reduce droplet size and increase drift potential. • Nozzle Type - Use a nozzle type designed for the intended application. With most nozzle types, narrower spray angles produce larger droplets. Consider using low-drift nozzles. Solid-stream nozzles oriented straight back produce the largest droplets and the lowest drift. DO NOT use nozzles producing a mist droplet spray. Boom Length For some use patterns, reducing the effective boom length to less than 3/4 of the wingspan or rotor length may further reduce drift without reducing swath width. Application Height Making applications at the lowest possible height (aircraft, ground-driven spray boom) that is safe and practical reduces exposure of droplets to evaporation and wind. Applications should not be made at a height greater than 10 feet above the top of the largest plants unless a greater height is required for aircraft safety. Swath Adjustment When applications are made with a crosswind, the swath will be displaced downwind. Therefore, on the upwind and downwind edges of the field, the applicator must compensate for this displacement by adjusting the path of the application equipment (e.g. aircraft, ground) upwind. Swath adjustment distance should increase with increasing drift potential (higher wind, smaller droplets, etc.). Wind Drift potential is lowest between wind speeds of 3 to 10 mph. However, many factors, including droplet size and equipment type, determine drift potential at any given speed. Avoid application below 3 mph because of variable wind direction and high inversion potential. NOTE: Local terrain can influence wind patterns. Every applicator should be familiar with local wind patterns and how they affect spray drift. Temperature and Humidity When making applications in low relative humidity, set up equipment to produce larger droplets to compensate for evaporation. Droplet evaporation is most severe when con- ditions are both hot and dry. Temperature Inversion Applications should not occur during temperature inversion because drift potential is high. Temperature inversions restrict vertical air mixing, which causes small suspended droplets to remain in a concentrated cloud that can move in unpredictable directions because of the light, variable winds common during inversions. Temperature inversions are characterized by increasing temperatures with altitude and are common on nights with limited cloud cover and light-to-no wind. They begin to form as the sun sets and often continue into the morning. Their presence can be indicated by ground fog; however, if fog is not present, inversions can also be identified by the movement of smoke from a ground source or an aircraft smoke genera- tor. Smoke that layers and moves laterally in a concentrated cloud (under low wind conditions) indicates an inversion, while smoke that moves upward and rapidly dissipates indicates good vertical air mixing. Sensitive Areas Spray drift from applying this product may result in damage to sensitive plants adjacent to the treatment area. Only apply this product when the potential for drift to these and other adjacent sensitive areas (e.g. residential areas, bodies of water, known habitat for threatened or endangered species, or nontarget crops or plants) is mini- mal. DO NOT apply when the following conditions exist that increase the likelihood of spray drift from intended

9 targets: high or gusty winds, high temperatures, low humidity, temperature inversions. Wind Erosion Avoid treating powdery, dry, or light sandy soils when conditions are favorable for wind erosion. Under these conditions, the soil surface should first be settled by rainfall or irrigation. Aerial Application Method and Equipment Water Volume. Use 2 or more gallons of water per acre. The actual minimum spray volume per acre is determined by the spray equipment used. Use adequate spray volume to provide accurate and uniform distribution of spray parti- cles over the treated area and to avoid spray drift. Managing Spray Drift from Aerial Application Applicators must follow these requirements to avoid off- target drift movement: • Boom Length - The distance of the outermost nozzles on the boom must not exceed 3/4 the length of the wingspan or rotor. • Nozzle Orientation - Nozzles must always point back- ward parallel with the airstream and never be pointed downward more than 45 degrees. • Application Height - Without compromising aircraft safety, application should be made at a height of 10 feet or less above the crop canopy or tallest plants. Applicators must follow the most restrictive use cautions to avoid drift hazards, including those found in this labeling as well as applicable state and local regulations and ordinances. Ground Application (Banding) When applying Outlook® herbicide by banding, calculate the amount of herbicide and water volume per acre needed using the following formula: Ground Application (Broadcast) Water Volume. Use 5 or more gallons of water per acre. The actual minimum spray volume per acre is determined by the spray equipment used. Use adequate spray volume for accurate and uniform distribution of spray particles over the treated area and to avoid spray drift. Cleaning Spray Equipment Clean application equipment thoroughly by using a strong detergent or commercial sprayer cleaner according to the manufacturer’s directions and then triple rinsing the equip- ment before and after applying this product. Ground Application (Dry Bulk Fertilizer) Outlook may be impregnated or coated onto dry bulk granular fertilizer carriers for preplant surface, preplant incorporated, or preemergence application. Impregnation or coating may be conducted by the in-plant bulk system or the on-board system. When impregnated onto some dry fertilizer blends, Outlook may exhibit a strong odor. Perform the mixing operation in a well- ventilated area. Outlook may also be applied in herbicide tank mixes where the tank mix companion product is also registered for these application systems. Individuals or agents selling Outlook in these application systems are responsible for following all state and local regulations regarding fertilizer and herbicide blending. Addition of a drying agent may be necessary if the fertilizer and herbicide blend is too wet for uniform application because of high humidity, high urea concentration, or low fertilizer use rate. Slowly add the drying agent to the blend until a flowable mixture is obtained. Drying agents are not advised for use with on-board impregnation systems. Under some conditions, fertilizer impregnated with Outlook may clog air tubes or deflector plates on pneu- matic application systems. Mineral oil may be added to Outlook before blending with fertilizer to reduce plugging. DO NOT use drying agents when mineral oil is used. To avoid separation of Outlook and mineral oil mixes in cold temperatures, either keep mixture heated or agitated before blending with fertilizer. Mineral oil may be used at in-plant blending stations or on-board injection systems. Apply 200 to 750 pounds of the fertilizer and herbicide blend per acre. Application must be made uniformly to the soil to prevent possible crop injury and for satisfactory weed control. Impregnated fertilizer spread at 1/2 rate and overlapped to obtain a full rate will offer a more uniform dis- tribution. For granular fertilizer application to protect small birds and mammals, soil incorporation of the granules is required. A shallow (1 to 2 inches) incorporation is desir- able for improved weed control. Deeper incorporation may result in unsatisfactory weed control. Use the following formula to calculate the herbicide rate when using dry bulk fertilizer applications: Incompatible Mixtures DO NOT impregnate Outlook or Outlook mixes on ammonium nitrate, potassium nitrate, or sodium nitrate fer- tilizers or fertilizer blends. Single superphosphate (0-20-0) and triple superphosphate (0-46-0) may be impregnated only with Outlook alone. bandwidth in inches x broadcast rate per acre

banding herbicide rate per acrerow width in inches bandwidth in inches x broadcast volume per acre

banding water volume per acrerow width in inches fl ozs/A x 2,000 = fluid ounces per ton of fertilizerfertilizer (lbs/A)

10 Chemigation Application via Sprinkler and Drip Irrigation Systems Outlook® herbicide may be applied as a chemigation treatment through sprinkler irrigation systems. Apply this product ONLY through a sprinkler irrigation system of the following type: center pivot, end tow, hand move, lateral move, side (wheel) roll, or solid set. DO NOT apply this product through any other type of sprinkler irrigation system. Outlook may also be applied as a chemigation treatment through drip irrigation systems. All chemigation precautions mentioned in this label for sprinkler irrigation systems also apply for drip irrigation systems. Application may be made alone or in tank mixtures with other herbicides on this label registered for use in specified sprinkler or drip irrigation systems. Application must be made within specific crop stage timings and product use rates given in the container label Directions For Use. Uniform distribution of Outlook-treated irrigation water is the sole responsibility of the applicator and is required to avoid crop injury, lack of herbicide effective ness, or illegal pesticide residue in the crop. If you have questions about calibration, contact State Extension Service specialists, equipment manufacturers, or other experts. Proper calibration is the responsibility of the applicator. The system must be properly calibrated (with water only) to ensure the amount of Outlook applied corresponds to the specified rate. Apply Outlook in volume minimums of 0.33 to 0.67 inch of water using the lower volume for coarse-texture soils and the higher volume for fine- texture soils. Application made in high volumes of water (more than 1 inch) may result in reduced weed control. Meter herbicide dilution into irrigation water through the entire time of water application for center pivot and lateral move sprinkler systems. For solid-set and hand-move sprinkler irrigation systems and drip irrigation systems, apply Outlook through the system at the beginning of the set; then follow with additional water to reach volume mini- mums as listed by soil type. To increase calibration accuracy of injection metering equipment, dilute Outlook in a minimum of 3 parts water to 1 part Outlook. Maintain agitation in injection nurse tanks to keep a uniform herbi- cide suspension during application. Special instructions for chemigation:

1. DO NOT apply when wind speed favors drift beyond the area intended for treatment.
2. DO NOT connect an irrigation system used for pesticide application to a public water system unless the pesticide label-prescribed safety devices for public water systems are in place.
3. A person knowledgeable of the chemigation system and responsible for its operation, or under the supervision of the responsible person, shall shut the system down and make necessary adjustments should the need arise.
4. Recirculate and/or contain tail water (runoff water) from chemigation that contains Outlook in the field in a cistern or holding reservoir from the initial application and/or used only on adjacent, approved crops for which Outlook is registered for this type of application.
5. The pesticide injection pipeline must contain a functional, automatic, quick-closing check valve to prevent the flow of fluid back toward the injection pump. It must also con- tain a functional, normally closed, solenoid-operated valve located on the intake side of the injection pump and connected to the system interlock to prevent fluid from being withdrawn from the supply tank when the irrigation system is either automatically or manually shut down.
6. The sprinkler chemigation system must contain a func- tional check valve, vacuum-relief valve, and low-pressure drain appropriately located on the irrigation pipeline to prevent water-source contamination from backflow. In addition, systems must use a metering pump, such as a positive displacement injection pump (e.g. diaphragm pump) effectively designed and constructed of materials that are compatible with pesticides and capable of being fitted with a system interlock.
7. The sprinkler chemigation system must contain function- al interlocking controls to automatically shut off the pesticide injection pump when the water pump motor stops, or in cases where there is no water pump, when the water pressure decreases to the point where pesti- cide distribution is adversely affected.
8. The irrigation line or water pump must include a functional pressure switch that will stop the water pump motor when the water pressure decreases to the point where pesticide distribution is adversely affected. Chemigation systems connected to public water systems:
9. Public water system means a system for the provision to the public of piped water for human consumption if such system has at least 15 service connections or regularly serves an average of at least 25 individuals daily at least 60 days out of the year.
10. Chemigation systems connected to public water systems must contain a functional, reduced-pressure zone backflow preventer (RPZ) or the functional equiva- lent in the water supply line upstream from the point of pesticide introduction. As an option to the RPZ, discharge the water from the public water system into a reservoir tank prior to pesticide introduction. There shall be a complete physical break (air gap) between the out- let end of the fill pipe and the top or overflow rim of the reservoir tank of at least twice the inside diameter of the fill pipe.
11. All chemigation systems connected to public water sys- tems must also follow restrictions listed in the preceding section. Additives Spray adjuvants have little or no influence on Outlook per- formance when application is made before weed emergence. However, several tank mixes with Outlook require adjuvants to improve burndown of emerged weeds. Therefore, surfactants and/or low rate fertilizer [28%, 30%,

11 or 32% urea ammonium nitrate (UAN) or ammonium sulfate (AMS)], or crop oil concentrate (COC) may be used with Outlook ® herbicide tank mixes applied preplant, preemer- gence, or early postemergence to the crop. Follow the adjuvant directions on the tank mix partner’s label. When an adjuvant (or a specific adjuvant product, such as a drift control agent) is to be used with this product, BASF recommends the use of a Chemical Producers and Distributors Association (CPDA) certified adjuvant for use on food crops. Oil Concentrate A crop oil concentrate must contain either a petroleum-oil or vegetable-oil base and must meet all of the following criteria: • Nonphytotoxic • Contain only EPA-exempt ingredients • Provide good mixing quality in the jar test • Successful in local experience The exact composition of suitable products will vary; how- ever, vegetable-oil and petroleum-oil concentrates should contain emulsifiers to provide good mixing quality. Highly refined vegetable oils have proven more satisfactory than unrefined vegetable oils. For additional information, see Compatibility Test for Mix Components. The use of adjuvants containing penetrants, such as petroleum-based oils, after corn emergence may cause crop injury. Nitrogen Source Urea Ammonium Nitrate (UAN). Use 1 to 2 gallons of UAN (28%, 30%, or 32% nitrogen solution) per acre. DO NOT use brass or aluminum nozzles when spraying UAN. Ammonium Sulfate (AMS). AMS at 8 to 17 pounds per 100 gallons of spray solution may be substituted for UAN. Use high-quality AMS (spray grade) to avoid nozzle plug- ging. Other sources of nitrogen are not as effective as those mentioned. BASF does not recommend applying AMS if applied in less than 10 gallons per acre because of potential problems with precipitation in reduced volumes. Use AMS only if it has been demonstrated to be successful in local experience. Nonionic Surfactant (NIS) The standard label recommendation is 1 to 2 quarts of an 80% active (NIS) per 100 gallons of water. For certain weeds, a higher spray surfactant rate is advised. Tank Mixing Information It is the pesticide user’s responsibility to ensure that all products in the mixtures are registered for the intended use. Read and follow the applicable restrictions and limita- tions and directions for use on all product labels involved in tank mixing. Users must follow the most restrictive directions for use and precautionary statements of each product in the tank mixture. Outlook may be tank mixed or applied sequentially with other herbicide products registered for use in any labeled crop found in this label for a broader spectrum of residual weed control and/or control of emerged weeds. Refer to the tank mix product labels to confirm that the respective tank mix products are registered for use on the labeled crop. Read and follow tank mix product labels for applica- tion instructions, use restrictions and precautions, and rotational cropping guidance. Physical incompatibility, reduced weed control, or crop injury may result from mix- ing Outlook with other pesticides (fungicides, herbicides, insecticides, or miticides), additives, or fertilizers. Local agricultural authorities may be a source of information when using other than BASF-advised tank mixes. Compatibility Test for Mix Components Before mixing components, always perform a compatibility jar test. For 20 gallons/A spray volume, use 3.3 cups (800 mL) of water. For other spray volumes, adjust rates accordingly. Only use water from the intended source at the source temperature. Add components in the sequence indicated in Mixing Order using 2 teaspoons for each pound or 1 teaspoon for each pint of label rate per acre. Always cap the jar and invert 10 cycles between compo- nent additions. When the components have all been added to the jar, let the solution stand for 15 minutes. Evaluate the solution for uniformity and stability. The spray solution should not have free oil on the surface, or fine particles that precipitate to the bottom, or thick (clabbered) texture. If the spray solution is not compatible, repeat the compatibility test with the addition of a suitable compatibility agent. If the solution is then compatible, use the compatibility agent as directed on its label. If the solution is still incompatible, DO NOT mix the ingredients in the same tank. Mixing Order Maintain constant agitation throughout mixing and application.

1. Water - Begin by agitating a thoroughly clean sprayer tank 3/4 full of clean water.
2. Inductor - If an inductor is used, rinse it thoroughly after each component has been added.
3. Products in PVA bags - Place any product contained in water-soluble PVA bags into the mixing tank. Wait until all water-soluble PVA bags have fully dissolved and the product is evenly mixed in the spray tank before continuing.
4. Water-dispersible products (dry flowables, wettable powders, suspension concentrates, or suspo- emulsions)
5. Water-soluble products
6. Emulsifiable concentrates (such as Outlook or oil concentrate when applicable)

12 7. Water-soluble additives (such as AMS or UAN when applicable) 8. Remaining quantity of water Use Restrictions • Maximum seasonal application rate - DO NOT apply more than a total of 0.98 pound of active ingredient dimethenamid-P (21 fl ozs of Outlook ® herbicide) per acre per season in all labeled crops except corn, cotton, sugar beet, and soybean. See Crop-specific Information section for maximum seasonal application rate in corn, cotton, sugar beet, and soybean. • Preharvest Interval (PHI) - Refer to Crop-specific Information for crop-specific preharvest intervals and feeding and grazing restrictions. • Outlook is not for sale, distribution, or use in Nassau and Suffolk counties in New York State. • DO NOT contaminate irrigation ditches or water used for domestic purposes. Use Precautions • Emergency replanting (recropping) intervals

• If corn, dry bean, grain sorghum, peanut, or soybean treated with Outlook are lost to adverse weather or for other reasons, the area treated may be replanted to any of those crops immediately, unless specified otherwise in the Crop-Specific Information section of this label.
• If the original Outlook treatment was broadcast, DO NOT make a second application of Outlook.
• If the original application was banded and the second crop is planted in the row middles, a second band application may be applied.
• If Outlook has been applied to sugar beets, table beets, cotton, dry bulb onions, garlic, dry bulb shallots, green onions, hops, perennial grass grown for seed, horseradish, potato, sweet potato, tuberous and corm vegetables, radish, rutabaga, turnip, pumpkin, or winter squash and crop failure occurs because of adverse weather or other reasons, replant ing (recropping) these crops is not advised. If replanting a crop is necessary, plant any of the following labeled crops (corn, dry bean, grain sorghum, peanut, soybean) where soil application of Outlook is registered. • Stress - Application to crops under stress because of lack of moisture, hail damage, flooding, herbicide injury, mechanical injury, or widely fluctuating temperatures may result in crop injury. Crop Rotation Intervals Refer to Table 3 to determine the proper interval between Outlook application and the planting of rotational crops. Determine the rotational crop interval for tank mix products and use the most restrictive interval of all products applied. Table 3. Rotational Crop Planting Intervals by Outlook Application Rate

• Cover crops (winter, spring) may be planted after application of Outlook, either inter-seeded into the current crop before harvest or after harvest of the current crop. Depending on the sensitivity of the sown cover crop to Outlook, stand establishment may be reduced. If cover crops are sown for conservation purposes prior to a 4-month interval, DO NOT harvest as a food or feed crop, or allow livestock to graze cover crops. Crop-specific Information Beet, Sugar Outlook may be used as part of a weed management program in sugar beet. Normal Timing Apply Outlook after sugar beets have reached the 2-leaf stage (at least 2 fully expanded true leaves) but before sugar beets have exceeded the 8-leaf stage. Application at 2-leaf stage or later may result in temporary leaf injury. Application made from preemergence up through cotyledon stage of beets may result in significant crop injury including possible stand reduction. Extended Timing Apply Outlook after sugar beets have reached the 9-leaf stage but before sugar beets have exceeded the 12-leaf stage. Refer to Table 2 for specific maximum application rates of Outlook depending on soil type and organic matter content. Outlook may be applied in a single application or two split applications. If Outlook is applied only as a single applica- tion, DO NOT exceed 21 fl ozs/A. If Outlook is applied in two split applications, maintain a minimum of 14 days between split applications. DO NOT exceed a seasonal total of 24 fl ozs/A of Outlook. If two applications are made, apply no more than 12 to 16 fl ozs/A during the first application (applied during Normal Timing: 2 true-leaf to 8 true-leaf stage); then the remainder (8 to 12 fl ozs/A) of the seasonal maximum rate during the second application (applied during Extended Timing: 9-leaf to 12-leaf true- leaf stage). Crop Outlook Use Rate (fl ozs/A) < 16 16 to 21 Rotational Crop Interval (months after application) Alfalfa 4 6 Canola (rapeseed) 4 6 Cotton 4 4 Peas (dry field, edible) 4 4 Small grains 4 4 Cover crops (winter, spring)* 4 6 Other crops 6 9

13 Crop-specific Restrictions • Harvest only mature beets and tops. • Preharvest Interval (PHI) for Normal Timing application: 60 days • Preharvest Interval (PHI) for Extended Timing applica- tion: 95 days Sugar Beet Tank Mixes Application may be made alone or in tank mixtures with other registered herbicides on sugar beet. Crop injury is possible when tank mixing other herbicides as well as any adjuvants such as methylated seed oils with Outlook ® herbicide. Read and follow the applicable Crop-specific Restrictions and Directions For Use on all products involved in tank mixing. The most restrictive labeling applies to tank mixes. Beet, Table (Garden) Outlook may be used as part of a weed management pro- gram in table (garden) beet. Apply Outlook after table beets have reached the 2-leaf stage (at least 2 fully expanded true leaves) but before table beets have exceeded the 6-leaf stage. Application at 2-leaf stage or later may result in temporary leaf injury. Application made from preemergence up through cotyledon stage of table beets may result in signifi- cant crop injury including possible stand reduction. A total maximum combined rate of 21 fl ozs/A of Outlook may be applied on any soil type in a single growing season. Refer to Table 2 for specific maximum application rates of Outlook depending on soil type and organic matter content. Outlook may be applied in single application or two split applications (such as micro-rate programs). If two applica- tions are made, maintain a minimum of 14 days between split applications. If two applications are made, apply 1/2 to 2/3 of rate during first application; then the remainder of rate during second application. If two applications are made, DO NOT exceed a total of 21 fl ozs/A of Outlook per season. Crop-specific Restrictions • Harvest only mature beets and tops. • Preharvest Interval (PHI) for beets and tops: 60 days Field Corn (grain, seed, silage), Fresh Sweet Corn, Popcorn Use not permitted in California on sweet corn. Outlook may be applied preplant surface, preplant incor- porated, preemergence, or postemergence to corn up to 12-inches tall. Corn in this label refers to field corn grown for grain, seed, or silage; fresh sweet corn; and popcorn. Before applying to seed corn, sweet corn, or popcorn, ver- ify with your local seed company (supplier) the Outlook selectivity on your inbred line or hybrid to avoid potential injury. Outlook may also be applied at layby to field corn, seed corn, and popcorn. Layby applications are made when corn is greater than 12-inches tall but before it is greater than 36-inches tall. For layby application for control of late - season germinating weeds, apply before weeds emerge from soil or in combination with a herbicide(s) and/or culti- vation that controls emerged weeds. For best performance, direct application beneath the corn canopy. Outlook may be applied in a single application or two split applications. Refer to Table 2 for specific maximum application rates of Outlook depending on soil type and organic matter content. If Outlook is applied in two split applications, maintain a minimum of 14 days between split applications, and DO NOT exceed a seasonal total of 24 fl ozs/A of Outlook. If two applications are made, apply no more than 8 to 16 fl ozs/A during the first application (applied preplant, preemergence, or postemergence); then apply the remainder (8 to 16 fl ozs/A) of the seasonal maximum rate during the second application (postemergence, layby). Crop-specific Restrictions • Corn may be grazed or fed to livestock 40 days or more after application of Outlook. • Preharvest Interval (PHI) for sweet corn ears: 50 days • DO NOT make layby application of Outlook to sweet corn. Corn Tank Mixes Refer to the tank mix product labels to confirm the respec- tive tank mix products are registered for use on specific corn types. Not all corn products are registered for use on seed corn, popcorn, and sweet corn. Glyphosate-resistant Corn Programs Outlook may be used preemergence and postemergence to glyphosate-resistant corn hybrids. Refer to a glyphosate product label for specific weeds controlled post emergence. Sequential Program Outlook may be applied preemergence at 12 fl ozs/A in a planned preemergence followed by glyphosate postemer- gence sequential program. Postemergence Tank Mix Program Outlook may be applied at 12 fl ozs/A in a postemergence tank mix with glyphosate to corn up to 12-inches tall. Layby application may also be made when corn is greater than 12-inches tall but before it is greater than 36-inches tall. Drop nozzles are required when corn is 30-inches to 36-inches tall. Labeled use rates for this tank mix are listed in Table 4. This tank mix with glyphosate should be applied when weeds are 2 inches to 4 inches in height and before weed height and/or density become competitive with the crop.

14 Table 4. Broadcast Application Rate per Acre Cotton Use not permitted in California on cotton. Outlook may only be applied postemergence to cotton for residual weed control. Before applying to cotton, verify with your local seed company (supplier) the selectivity of Outlook on your variety to avoid potential injury. Use of Outlook may result in temporary growth suppres- sion in cotton if extreme conditions of high rainfall and extended periods of water-saturated soil occur during cot- ton germination or early seedling development. Application Rate and Timing Outlook may be applied in either a single postemergence application (see Single Application section) or in sequen- tial postemergence applications (see Sequential Applications section). Early Postemergence Application Outlook must be applied before weed seedling emergence or in a tank mix with products registered for use on cotton that control the emerged weeds. For effec- tive residual activity, rainfall, sprinkler irrigation, or shallow mechanical incorporation after application is required to move this product into the upper soil surface where weed seeds germinate. Outlook will provide residual control of weeds germinating after application. Weeds that are emerged at time of appli- cation must be controlled with cultivation, or a tank mix or sequential application of another herbicide labeled for postemergence weed control in cotton. Outlook application to emerged cotton may result in tem- porary leaf burn, spotting, and/or stunting, but a reduction in cotton yield is not expected. Adjuvants may be applied with Outlook when making early postemergence application. Single application. Apply Outlook at up to 21 fl ozs/A as a broadcast spray to cotton from first true leaf stage to the mid-bloom stage (i.e. two weeks after R1 initial bloom stage). DO NOT apply more than 21 fl ozs/A of Outlook in a single application. Sequential application. Outlook may be applied as split applications when both the initial and sequential application is made early postemergence. With the initial application, apply Outlook very early postemergence (typically from first true leaf stage to 6 to 10 leaf stage) at 12 to 18 fl ozs/A as a broadcast spray to cotton. For the sequential applica- tion, apply Outlook early postemergence (up to the mid-bloom stage, i.e. two weeks after R1 initial bloom stage) at 13 to 19 fl ozs/A as a broadcast spray to cotton. Sequential applications must be separated by at least 14 days. DO NOT apply more than 31 fl ozs/A of Outlook from early postemergence applications. Crop-specific Restrictions • DO NOT apply preplant surface, preplant incorporated, or preemergence in cotton. • DO NOT apply more than a maximum cumulative amount of 31 fl ozs/A of Outlook per year. • There is no required (preharvest) interval between a postemergence application of Outlook and the harvest of cotton. • Cotton gin byproducts may be fed to livestock. Cotton Tank Mixes Tank mixing Outlook with other emulsifiable concentrate (EC) formulated products may enhance potential for cotton injury response. Dry Bean Use not permitted in California on dry bean. Outlook may be applied preplant surface, preplant incor- porated, preemergence, or early postemergence (first to third trifoliate stage) to dry bean classes (black turtle soup, cranberry, dry lima, great northern, navy, pink, pinto, red kidney, red Mexican, and small whites). Outlook may only be applied preplant surface or preemergence to garbanzo beans and lentils. Outlook is not registered for use in suc- culent beans, succulent bean varieties grown for seed, or cowpeas. Before applying Outlook to dry beans, verify with your local seed company (supplier) the selectivity of Outlook on your specific dry bean class and variety to help avoid potential injury to sensitive classes or varieties. If extreme conditions of high rainfall and extended periods of water-saturated soil occur during dry edible bean germi- nation or early seedling development, Outlook use may result in temporary growth suppression. This suppression will not reduce dry edible bean yield. Outlook use postemergence may occasionally result in some temporary spotting or browning of dry bean leaves and stunting, but a reduction in dry bean yield is unexpected. Postemergence tank mixtures with other crop protection products or adjuvants may significantly enhance this effect. Depending on growing conditions, recovery from this injury begins immediately but may take several weeks for dry beans to recover completely. Refer to Table 2 for specific maximum application rates of Outlook depending on soil type and organic matter content. Outlook may be applied in a single application of up to 21 fl ozs/A or used in split applications of 10 to 14 fl ozs/A of Outlook applied initially, and the remaining 7 to 11 fl ozs/A of Outlook in the sequential application. Soil Texture Group Outlook® herbicide (fl ozs) glyphosate Coarse 10 to 12 labeled rate Medium 12 to 14 labeled rate Fine 12 to 16 labeled rate

15 DO NOT exceed a total of 21 fl ozs/A of Outlook® herbicide per season. Additional restrictions specific to dry beans are to use a maximum of 12 fl ozs/A of Outlook on coarse soils with organic matter less than 1.5% for soil applications made before crop emergence. Crop-specific Restrictions • DO NOT apply Outlook early postemergence to dry beans grown in the states of Washington and Oregon (EXCEPTION: Malheur county). • DO NOT apply Outlook early postemergence by chemi- gation to dry beans grown in Idaho or Malheur County, Oregon. • Preharvest Interval (PHI): 70 days Dry Bean Tank Mixes The following herbicide products may only be applied sequentially with Outlook: • Dual II Magnum® herbicide • Dual Magnum® herbicide Dry Bulb Onions, Garlic, Dry Bulb Shallots Outlook may be used as part of a weed management pro- gram in dry bulb onions, garlic, and dry bulb shallots grown in muck soils, high organic soils, and in mineral soils. Apply Outlook after dry bulb onions, garlic, and dry bulb shallots have reached the 2 true-leaf stage until a minimum of 30 days before harvest. Application made before 2 true-leaf stage may result in significant crop injury includ- ing possible stand reduction. If applications are made to transplanted dry bulb onions, garlic, and dry bulb shallots, DO NOT apply until transplants are in the ground and soil has settled around transplants with several days to recover. Outlook may be applied in a single application of up to 21 fl ozs/A or used in split applications of 10 to 14 fl ozs/A of Outlook applied initially, and the remaining 7 to 11 fl ozs/A of Outlook in the sequential application. If split applications are made, maintain a minimum of 14 days between sequential applications. DO NOT apply more than a total of 21 fl ozs/A of Outlook in a single growing season. A total maximum combined rate of 21 fl ozs/A of Outlook may be applied on any soil type in a single growing season. Refer to Table 2 for specific maximum application rates of Outlook depending on soil type and organic matter content. Crop-specific Restrictions • Preharvest Interval (PHI): 30 days Dry Bulb Onions, Garlic, Dry Bulb Shallots Tank Mixes Crop injury is possible when tank mixing other herbicides as well as any adjuvants such as methylated seed oils with Outlook. Read and follow the applicable Crop-specific Restrictions and Directions For Use on all products involved in tank mixing. The most restrictive labeling applies to tank mixes. Fallow Outlook may be used as a residual treatment to control listed weeds before they germinate at the beginning of the fallow period. Specific rotational crop planting intervals must be observed between an application of Outlook and planting of the following crops (see Crop Rotation Intervals section). Application Rate and Timing Apply Outlook as a broadcast spray at up to 21 fl ozs/A before weeds emerge for best product performance. Split applications may be made with a minimum of 30 days between applications; but DO NOT exceed the maximum seasonal cumulative amount of 21 fl ozs/A of Outlook per cropping season. Use not permitted in California on green onions. Outlook may be used as part of a weed management pro- gram in green onions grown in muck soils, high organic soils, and mineral soils. Outlook may only be applied by ground (broadcast) application. Apply Outlook after green onions have reached the 2 true- leaf stage until a minimum of 30 days before harvest. Application made before 2 true-leaf stage may result in sig- nificant crop injury including possible stand reduction. If applications are made to transplanted green onions, DO NOT apply until transplants are in the ground and soil has settled around transplants with several days to recover. Outlook may be applied in a single application of up to 21 fl ozs/A or used in split applications of 10 to 14 fl ozs/A of Outlook applied initially, and the remaining 7 to 11 fl ozs/A of Outlook in the sequential application. If split applications are made, maintain a minimum of 14 days between sequential applications. DO NOT apply more than a total of 21 fl ozs/A of Outlook in a single growing season. Crop-specific Restrictions • Preharvest Interval (PHI): 30 days Green Onions (Leeks, Spring onions or Scallions, Japanese bunching onions, Green shallots or Eschalots)

Green Onion Tank Mixes Outlook® herbicide application may be made before, in tank mixture, or after use of registered herbicides for poste- mergence use in green onions. Crop injury is possible when tank mixing herbicides as well as any adjuvants such as methylated seed oils with Outlook. Read and follow the applicable Crop-specific Restrictions and Directions For Use on all products involved in tank mixing. The most restrictive labeling applies to tank mixes. Hops Use not permitted in California on hops. Outlook may be used as part of a weed management pro- gram in baby (first year planting) and established hops. Outlook may only be applied by ground (banded) application (including postemergence-directed). Contact with hop foliage or cones by spray mixture or drift may cause injury. Apply Outlook preemergence to weeds when hops are in the dormant or early vegetative stages of growth. Outlook may only be applied in single application. Outlook has not been tested on hops grown in all soil tex- tures. Refer to Table 2 for soil texture group descriptions and appropriate application rates. BASF recommends testing Outlook on a small portion of the target crop to confirm safety in the local soil type. Depending on application timing, Outlook may negatively impact growth of cover crops planted in the fall after harvest. Crop-specific Restrictions • DO NOT apply to hops by air or through any type of irri- gation system. • DO NOT apply more than 21 fl ozs/A of Outlook per season. • Preharvest Interval (PHI): 60 days Tank Mixes Tank mixes with other herbicides, fungicides, insecticides, and fertilizers are not advised when using this product in hops. Peanut Use not permitted in California on peanut. Outlook may be applied preplant surface, preplant incor- porated, preemergence, or postemergence (up to 80 days before harvest) alone or in tank mix combination. Use high- er rates (16 to 21 fl ozs/A of Outlook) for improved control or suppression of difficult weeds like yellow nutsedge, Florida beggarweed, eclipta, common ragweed, and other broadleaf species. Refer to Table 2 for specific maximum application rates of Outlook depending on soil type and organic matter content. Outlook may be applied in a single application of up to 21 fl ozs/A or used in split applications of 10 to 14 fl ozs/A of Outlook applied initially, and the remaining 7 to 11 fl ozs/A of Outlook in the sequential application. DO NOT apply more than 21 fl ozs/A of Outlook per season. Crop-specific Restrictions • Peanut hay or straw may be grazed or fed to livestock 80 days or more after application of Outlook. Perennial Grass grown for Seed For use on perennial grass grown for seed only in states west of the Mississippi River. Outlook may be used as part of a weed management program in established stands of cool- season and warm- season perennial grass grown for seed. Grass seed crops must have been established for at least one year or had at least one seed crop harvested before Outlook use. The grass seed screenings remaining after processing and grass straw remaining after seed harvest may be grazed by or fed to livestock. Outlook applied as directed will provide preemergence control or suppression of volunteer seedlings from previous grass seed crops in addition to many annual grass weeds, annual broadleaf weeds, and sedge listed in Table 1. In cool-season perennial grass, apply 14 to 21 fl ozs/A of Outlook to postharvest grass during regrowth in the fall or spring before emergence of targeted weeds. Outlook may be applied in a sequential use program with other herbicides that control emerged weeds. Application to perennial ryegrass and fine fescue stands under stress may cause crop injury. In warm-season perennial grass, apply 14 to 21 fl ozs/A of Outlook to postharvest grass during the fall, or during win- ter dormancy, or after the first seed harvest/cutting. DO NOT apply to warm-season perennial grass after greenup in the spring before the first seed harvest/cutting. Outlook may be applied in a sequential use program with other herbicides that control emerged weeds. In both cool-season and warm- season perennial grass, use the higher rate in the rate range where more dense infestations of targeted annual grass weeds, annual broadleaf weeds, or sedge are expected. Grass straw from the previous harvest must be removed, burned, or evenly spread before Outlook application or reduced weed con- trol may result. For effective control or suppression of annual grass weeds, annual broadleaf weeds, sedge, or volunteer seedlings from previous grass seed crops, this product must be moved into the upper soil surface where weed seeds germinate by rainfall or irrigation before weed emergence. 16

17 Application made in periods of cold temperature that tem- porarily limit normal crop growth or in extended cold temperature periods that initiate winter dormancy in grass crops may result in crop injury. Outlook ® herbicide may be tank mixed with other herbi- cides labeled for use in perennial grass grown for seed. BASF recommends testing Outlook tank mixes on a small portion of the target crop to determine if damage is likely to occur. Physical incompatibility, reduced weed control, or crop injury may result from mixing Outlook with other pesticides (fungicides, herbicides, insecticides, or miticides), additives, or fertilizers. Subsequent appli- cation of postemergence herbicides may cause crop injury. Consult with your local BASF dealer regarding local tank mix options. Crop-specific Restrictions • DO NOT apply a total of more than 21 fl ozs/A of Outlook per growing season. • From treated fields of cool-season perennial grass, forage and hay may be grazed by or fed to livestock 60 days after application. • From treated fields of warm-season perennial grass, for- age and hay may be grazed by or fed to livestock 30 days after application. Potato, Sweet Potato, Horseradish Use not permitted on horseradish and sweet potato in California. Outlook may be used as part of a weed management program in horse radish, potato, and sweet potato. In potato and sweet potato, apply Outlook preemergence (after planting or after drag-off). In horseradish, apply Outlook postemergence from the 2-leaf stage to the 8-leaf stage of plant development. Outlook may only be applied in a single application in horseradish, potato, and sweet potato. In cold and wet growing conditions, Outlook application may result in delayed emergence or early season stunting of horseradish, potato, and sweet potato. Outlook use can cause crop injury to sweet potatoes. Apply Outlook preemergence only. Apply Outlook so as not to come into contact with developing tubers. The option of applying Outlook for weed control rather than crop injury should be based on potential crop loss because of weed infestations compared to potential loss from crop injury. Test Outlook on a portion of the crop to determine if the use of Outlook is suitable for the intended results. Refer to Table 2 for specific maximum application rates of Outlook depending on soil type and organic matter con- tent. DO NOT exceed the specified rate by soil type and organic matter content in a single application. Crop-specific Restrictions • Preharvest Interval (PHI): 40 days Sorghum (Grain) Outlook may be used preplant surface, preplant incorpo- rated, preemergence, or postemergence to grain sorghum up to 12-inches tall. Single or split application may be used. Outlook is not registered for use on sweet or forage sorghum. All Outlook applications must only be made to sorghum seed that has been properly treated by the seed company with an approved chloroacetamide herbicide safener or severe injury may occur. Under high soil moisture or cool conditions, Outlook appli- cation may cause temporary stunting or leaf wrapping of sorghum. Sorghum will normally outgrow these symptoms in 10 to 14 days. For best performance, make preemergence surface application within 5 days of the last preplant tillage. If weeds have emerged, apply Outlook with herbicides to control emerged vegetation. Refer to Table 2 for specific maximum application rates of Outlook depending on soil type and organic matter content. Crop-specific Restrictions • Sorghum forage may be grazed or fed to livestock 60 days or more after application of Outlook. • Preharvest Interval (PHI) for grain and fodder: 80 days • DO NOT apply preplant incorporated in California. Soybean Use not permitted in California on soybean. Outlook may be applied preplant surface, preplant incor- porated, preemergence, or postemergence [from emergence (cracking stage) to fifth-trifoliate leaf stage] to soybean. If Outlook is applied preplant incorporated, incorporation must be uniform and shallow (upper 1 to 2 inches of soil). Deeper incorporation may reduce weed control or increase the potential for crop injury. Preplant incorporated treatments are not for use on coarse soils with less than 1.5% organic matter. If extreme conditions of high rainfall and extended periods of water-saturated soil occur during soybean germination or early seedling development, Outlook use may result in temporary growth suppression. Temporary soybean burn and/or stunting may occur with postemergence applications of Outlook. Tank mixtures with other herbicides not listed in the Soybean Tank Mixes section and/or spray adjuvants may increase the level of crop injury. Crop injury is typically transient and has not resulted in reduced soybean yield potential. Outlook may be applied in a single application or two split applications.

18 Refer to Table 2 for specific maximum application rates of Outlook® herbicide depending on soil type and organic matter content. If Outlook is applied only as a single application, DO NOT apply more than 21 fl ozs/A. If Outlook is applied in two split applications, maintain a minimum of 14 days between split applications, and DO NOT exceed a seasonal total of 24 fl ozs/A of Outlook. If two applications are made, apply no more than 8 to 16 fl ozs/A during the first application (applied preplant, preemergence, or postemergence); then apply the remainder (8 to 16 fl ozs/A) of the seasonal maxi- mum rate during the second application (postemergence). Crop-specific Restrictions • DO NOT graze or feed forage, hay, or straw to livestock. Tuberous and Corm Vegetables Use not permitted in California on tuberous and corm vegetables. Outlook may be used as part of a weed management pro- gram in the following tuberous and corm vegetables: arracacha, arrowroot, Chinese and Jerusalem artichoke, edible canna, bitter and sweet cassava, root chayote, chufa, dasheen, ginger, leren, tanier, turmeric, yam bean, true yam. In tuberous and corm vegetables, apply Outlook pre- emergence (after planting or after drag-off). In cold and wet growing conditions, Outlook application may result in delayed emergence or early season stunting of tuberous and corm vegetables. Outlook may only be applied in a single application in tuberous and corm vegetables. Refer to Table 2 for specific maximum application rates of Outlook depending on soil type and organic matter content. Crop-specific Restrictions • Preharvest Interval (PHI): 40 days Turnip, Radish, Rutabaga Outlook may be used as part of a weed management program in radish, rutabaga, and turnip. Outlook may only be applied by ground (broadcast) application. Apply Outlook after rutabaga and turnip have reached the 2-leaf stage (at least 2 fully expanded true leaves) but before rutabaga and turnip have exceeded the 8-leaf stage. Application at 2-leaf stage or later may result in tem- porary leaf injury. Application made from preemergence through cotyledon stage of rutabaga and turnip may result in significant crop injury including possible stand reduction. Apply Outlook after radish has reached the 2-leaf stage (at least 2 fully expanded true leaves) but before radish has exceeded the 4-leaf stage. Application at 2-leaf to 4-leaf stage may result in temporary leaf injury. Application made from preemergence through cotyledon stage of radish may result in significant crop injury including possible stand reduction. Outlook may only be applied in single application. Refer to Table 2 for specific maximum application rates of Outlook depending on soil type and organic matter content. Crop-specific Restrictions • DO NOT apply to radish, rutabaga, and turnip by air or through any type of irrigation system. • DO NOT apply more than 21 fl ozs/A of Outlook per season. • Harvest only mature tops and roots of radish, rutabaga, and turnip. • Preharvest Interval (PHI) for rutabaga and turnip tops: 14 days • Preharvest Interval (PHI) for rutabaga and turnip roots: 40 days • Preharvest Interval (PHI) for radish tops and roots: 21 days Tank Mixes Tank mixes with other herbicides or insecticides are not advised when applying this product in radish, rutabaga, and turnip. Winter Squash, Pumpkin For use only in Oregon and Washington. Outlook may be used as part of a weed management program in pumpkin and winter squash (Golden Delicious variety only). Outlook may only be applied by ground (broadcast) application. Apply Outlook as a preemergence surface application. Broadcast the treatment uniformly to the soil surface after planting and before crop and weed emergence. If extreme conditions of high rainfall and extended periods of water- saturated soil occur during pumpkin or winter squash germination or early seedling development, Outlook use may result in growth suppression, which may reduce yields. Outlook may only be applied in single application. Apply a minimum of 12 to 14 fl ozs/A of O utlook on soils with less than 3% organic matter. Apply a minimum of 16 to 18 fl ozs/A on soils with greater than 3% organic matter. DO NOT apply more than 21 fl ozs/A of Outlook on any soil in a single application.

19 Crop-specific Restrictions • DO NOT apply to pumpkin or winter squash by air or through any type of irrigation system. • DO NOT apply when conditions favor drift to adjacent susceptible vegetation. • DO NOT apply more than 21 fl ozs/A of Outlook® herbicide per year in pumpkin or winter squash. • Preharvest Interval (PHI): 90 days Tank Mixes Tank mixes with other herbicides or insecticides are not advised when using this product in pumpkin or winter squash.

20 Outlook is a registered trademark of BASF. Dual II Magnum and Dual Magnum are registered trade- marks of a Syngenta Group Company. Dual Magnum® herbicide (s-metolachlor), EPA Reg. No. 100-816 Dual II Magnum® herbicide (s-metolachlor), EPA Reg. No. 100-818 © 2019 BASF Corporation All rights reserved. 007969-00156.20180131b.NVA 2018-04-086-0016 Supersedes: NVA 2017-04-086-0063 Supplemental: NVA 2018-04-086-0015 BASF Corporation 26 Davis Drive Research Triangle Park, NC 27709 Conditions of Sale and Warranty The Directions For Use of this product reflect the opinion of experts based on field use and tests. The directions are believed to be reliable and must be followed carefully. However, it is impossible to eliminate all risks inherently associated with the use of this product. Crop injury, ineffectiveness or other unintended consequences may result because of such factors as weather conditions, presence of other materials, or use of the product in a manner inconsistent with its labeling, all of which are beyond the control of BASF CORPORATION (“BASF”) or the Seller. To the extent consistent with applicable law, all such risks shall be assumed by the Buyer. BASF warrants that this product conforms to the chemical description on the label and is reasonably fit for the purposes referred to in the Directions For Use, subject to the inherent risks, referred to above. TO THE EXTENT CONSISTENT WITH APPLICABLE LAW, BASF MAKES NO OTHER EXPRESS OR IMPLIED WARRANTY OF FITNESS OR MERCHANTABILITY OR ANY OTHER EXPRESS OR IMPLIED WARRANTY. TO THE EXTENT CONSISTENT WITH APPLICABLE LAW, BUYER’S EXCLUSIVE REMEDY AND BASF’S EXCLUSIVE LIABILITY, WHETHER IN CONTRACT, TORT, NEGLIGENCE, STRICT LIABILITY, OR OTHERWISE, SHALL BE LIMITED TO REPAYMENT OF THE PURCHASE PRICE OF THE PRODUCT. TO THE EXTENT CONSISTENT WITH APPLICABLE LAW, BASF AND THE SELLER DISCLAIM ANY LIABILITY FOR CONSEQUENTIAL, EXEMPLARY, SPECIAL OR INDIRECT DAMAGES RESULTING FROM THE USE OR HANDLING OF THIS PRODUCT. BASF and the Seller offer this product, and the Buyer and User accept it, subject to the foregoing Conditions of Sale and Warranty which may be varied only by agreement in writing signed by a duly authorized representative of BASF. 1108

BASF Corporation 26 Davis Drive, Research Triangle Park, NC 27709

Supplemental Label

Increased rate for early postemergence sequential applications in cotton This supplemental label expires November 30, 2022, and must not be used or distributed after this date. Active Ingredient*: dimethenamid-P: (S)-2-chloro-N-[(1-methyl-2-methoxy)ethyl]- N-(2,4-dimethyl-thien-3-yl)-acetamide ............................................................................................................. 63.9% Other Ingredients**: ....................................................................................................................................... 36.1% Total: ............................................................................................................................................................... 100.0%

• Contains 6.0 pounds of active ingredient per gallon ** Contains petroleum distillates

EPA Reg. No. 7969-156 KEEP OUT OF REACH OF CHILDREN WARNING/AVISO

Directions For Use • It is a violation of federal law to use this product in a manner inconsistent with its labeling. • The supplemental labeling and the entire Outlook® herbicide container label, EPA Reg. No. 7969-156, must be in possession of the user at the time of application. • Read the label affixed to the container for Outlook before applying. • Use of Outlook according to this labeling is subject to the use precautions and restrictions imposed by the label affixed to the container for Outlook. Product Information Outlook is a selective preemergence herbicide for controlling annual broadleaf weeds, annual grass weeds, and sedges. Refer to the Outlook container label for a complete list of weeds controlled.

Application Information Early Postemergence Application Outlook may be applied as split applications when both the initial and sequential application is made early postemergence. With the initial application, apply Outlook very early postemergence (typically from first true leaf stage to 6 to 10 leaf stage) at 12 to 18 fl ozs/A as a broadcast spray to cotton. For the sequential application, apply Outlook early postemergence (up to the mid-bloom stage, i.e. two weeks after R1 initial bloom stage) at 13 to 19 fl ozs/A as a broadcast spray to cotton. Sequential applications must be separated by at least 14 days. DO NOT apply more than 31 fl ozs/A of Outlook from early postemergence applications. Crop-specific Restrictions • DO NOT apply more than a maximum cumulative amount of 31 fl ozs/A of Outlook per year. • DO NOT apply preplant surface, preplant incorporated, or preemergence in cotton. • There is no required (preharvest) interval between a postemergence application of Outlook and the harvest of cotton. • Cotton gin byproducts may be fed to livestock.

Dimethenamid-P Group 15 Herbicide

11/29/2019 7969-156

2 Conditions of Sale and Warranty The Directions For Use of this product reflect the opinion of experts based on field use and tests. The directions are believed to be reliable and must be followed carefully. However, it is impossible to eliminate all risks inherently associated with the use of this product. Crop injury, ineffectiveness or other unintended consequences may result because of such factors as weather conditions, presence of other materials, or use of the product in a manner inconsistent with its labeling, all of which are beyond the control of BASF CORPORATION (“BASF”) or the Seller. To the extent consistent with applicable law, all such risks shall be assumed by the Buyer. BASF warrants that this product conforms to the chemical description on the label and is reasonably fit for the purposes referred to in the Directions For Use, subject to the inherent risks, referred to above. TO THE EXTENT CONSISTENT WITH APPLICABLE LAW, BASF MAKES NO OTHER EXPRESS OR IMPLIED WARRANTY OF FITNESS OR MERCHANTABILITY OR ANY OTHER EXPRESS OR IMPLIED WARRANTY. TO THE EXTENT CONSISTENT WITH APPLICABLE LAW, BUYER’S EXCLUSIVE REMEDY AND BASF’S EXCLUSIVE LIABILITY, WHETHER IN CONTRACT, TORT, NEGLIGENCE, STRICT LIABILITY, OR OTHERWISE, SHALL BE LIMITED TO REPAYMENT OF THE PURCHASE PRICE OF THE PRODUCT. TO THE EXTENT CONSISTENT WITH APPLICABLE LAW, BASF AND THE SELLER DISCLAIM ANY LIABILITY FOR CONSEQUENTIAL, EXEMPLARY, SPECIAL OR INDIRECT DAMAGES RESULTING FROM THE USE OR HANDLING OF THIS PRODUCT. BASF and the Seller offer this product, and the Buyer and User accept it, subject to the foregoing Conditions of Sale and Warranty which may be varied only by agreement in writing signed by a duly authorized representative of BASF. 1108

Outlook is a registered trademark of BASF.

© 2019 BASF Corporation All rights reserved.

007969-00156.20180131b.NVA 2018-04-086-0015

BASF Corporation 26 Davis Drive Research Triangle Park, NC 27709