crop-chem-docs/corpus/epa_ppls/279-9589.md

ALLY EXTRA HERBICIDE

• EPA Reg No: 279-9589
• Registrant: FMC CORPORATION
• Signal word: Caution
• Active ingredients: Metsulfuron-methyl (15%); Thifensulfuron (37.5%); Tribenuron-methyl (18.75%)
• Label accepted: 2020-05-01
• Source PDF: https://www3.epa.gov/pesticides/chem_search/ppls/000279-09589-20200501.pdf

---

UNITED STATES ENVIRONMENTAL PROTECTION AGENCY WASHINGTON, DC 20460

Amended Under Reregistration and Label Amendment v.20150612

OFFICE OF CHEMICAL SAFETY AND POLLUTION PREVENTION May 1, 2020

Edward Bockrath Product Registration Manager FMC Corporation 2929 Walnut Street Philadelphia, PA 19104

Subject: Registration Review Label Mitigation for Thifensulfuron, Tribenuron and Metsulfuron- methyl Product Name: ALLY EXTRA HERBICIDE EPA Registration Number: 279-9589 Application Date: 08/29/2018 Decision Numbers: 561682, 561686 and 561687

Dear Mr. Bockrath:

The Agency, in accordance with the Federal Insecticide, Fungicide and Rodenticide Act (FIFRA), as amended, has completed reviewing all of the information submitted with your application to support the Registration Review of the above referenced product in connection with the Sulfonylurea (SU) Herbicides Interim Decision, and has concluded that your submission is acceptable. The agency also completed review of your amended label referred to above, submitted in connection with registration under FIFRA, as amended, and has determined the label is also acceptable.

Should you wish to add/retain a reference to the company’s website on your label, then please be aware that the website becomes labeling under the Federal Insecticide Fungicide and Rodenticide Act and is subject to review by the Agency. If the website is false or misleading, the product would be misbranded and unlawful to sell or distribute under FIFRA section 12(a)(1)(E). 40 CFR 156.10(a)(5) list examples of statements EPA may consider false or misleading. In addition, regardless of whether a website is referenced on your product’s label, claims made on the website may not substantially differ from those claims approved through the registration process. Therefore, should the Agency find or if it is brought to our attention that a website contains false or misleading statements or claims substantially differing from the EPA approved registration, the website will be referred to the EPA’s Office of Enforcement and Compliance. A copy of your label stamped “Accepted” is enclosed. Products shipped after 12 months from the date of this amendment must bear the new revised label. Your release for shipment of the product bearing the amended label constitutes acceptance of these conditions. If these conditions are not complied with, the registration will be subject to cancellation in accordance with FIFRA section 6.

Page 2 of 2 EPA Reg. No. 279-9589 Decision No. 561682, 561686 and 561687

If you have any questions about this letter, please contact Srijana Shrestha by phone at 703-305- 6471, or via email at Shrestha.srijana@epa.gov .

Sincerely,

Linda Arrington, Branch Chief Risk Management and Implementation Branch 4 Pesticide Re-Evaluation Division Office of Pesticide Programs

Enclosure

HERBICIDE

ALLY® EXTRA For Use on Wheat, Barley, Triticale and Fallow. Active Ingredients By Weight Thifensulfuron methyl Methyl 3-[[[[(4-methoxy-6-methyl-1,3,5-triazin-2-yl) amino]carbonyl]amino]-sulfonyl]-2-thiophenecarboxylate 37.50% Tribenuron methyl Methyl 2-[[[[N-(4-methoxy-6-methyl-1,3,5-triazin-2-yl)methylamino]carbonyl]-amino]sulfonyl]benzoate 18.75% Metsulfuron methyl Methyl 2-[[[[(4-methoxy-6-methyl-1,3,5-triazin-2-yl)amino]carbonyl]amino]-sulfonyl]benzoate 15.00% Other Ingredients 28.75% TOTAL Contains 0.1500 lb Metsulfuron Methyl per pound Contains 0.3750 lb Thifensulfuron Methyl perpound EPA Est. No. 100% Contains 0.1875 lb Tribenuron Methyl perpound Nonrefillable Container OR Refillable Container EPA Reg. No. 279-9589 Net: Net: Sold By FMC Corporation 2929 Walnut Street Philadelphia, PA 19104 METSULFURON METHYL GROUP 2 HERBICIDE THIFENSULFURON METHYL GROUP 2 HERBICIDE TRIBENURON METHYL GROUP 2 HERBICIDE KEEP OUT OF REACH OFCHILDREN CAUTION Si usted no entiende la etiqueta, busque a alguien para que se la explique a usted en detalle. (If you do not understand this l abel, find someone to explain it to you in detail.) FIRST AID IF IN EYES: Hold eye open and rinse slowly and gently with water for 15-20 minutes. Remove contact lenses, if present, after the first 5 minutes, then continue rinsing eye. Call a poison control center or doctor for treatment advice. IF ON SKIN OR CLOTHING: Take off contaminated clothing. Rinse skin with plenty of water for 15-20 minutes. Call a poison control center or doctor for treatment advice. Have the product container or label with you when calling a poison control center or doctor, or going for treatment. You may also contact 1-800-331-3148 for emergency medical treatment information. PRECAUTIONARY STATEMENTS HAZARDS TO HUMANS AND DOMESTIC ANIMALS CAUTION! Causes moderate eye irritation. Harmful if absorbed through skin. Avoid contact with skin, eyes, or clothing. Wash thoroughly with soap and water after handling and before eating, drinking, chewing gum, using tobacco, or using the toilet. ALLY® EXTRA herbicide is a dry flowable granule that is used for selective postemergence weed control in wheat (including durum), barley, triticale and fallow.  May 01, 2020 279-9589

PERSONAL PROTECTIVE EQUIPMENT (PPE) Applicators and other handlers must wear: Long-sleeved shirt and long pants. Chemical Resistant Gloves made of any waterproof material >14 mls. Shoes plus socks. Follow manufacturer’s instructions for cleaning/maintaining PPE. If no such instructions for washables exist, use detergent and hot water. Keep and wash PPE separately from other laundry. ENVIRONMENTAL HAZARDS Do not apply directly to water, or to areas where surface water is present, or to intertidal areas below the mean high water mark. Do not contaminate water when cleaning equipment or disposing of equipment washwaters or rinsate. Groundwater Advisory This chemical has properties and characteristics associated with chemicals detected in groundwater. This chemical may leach into groundwater if used in areas where soils are permeable, particularly where the water table is shallow. Surface Water Advisory This product may impact surface water quality due to runoff of ra in water. This is especially true for poorly draining soils and soils with shallow ground water. This product is clas sified as having high potential for reaching surface water via runoff for days after application . A level, well-maintained vegetative buffer strip between areas to which this product is applied and surface water features such as ponds, streams, and springs will reduce the potential loading of this product from runoff water and sediment. Runoff of this product will be greatly reduced by avoiding applications when rainfall or irrigation is expected to occur within 48 hours. PESTICIDE HANDLING • Calibrate sprayers only with clean water away from the wellsite. • Make scheduled checks of spray equipment. • Ensure that all operation employees accurately measure pesticides. • Mix only enough product for the job at hand. • Avoid overfilling of spray tank. • Do not discharge excess material on the soil at a single spot in the field, grove, or mixing/loadingstation. • Avoid storage of pesticides near well sites. DIRECTIONS FOR USE It is a violation of Federal law to use this product in a manner inconsistent with its labeling. DO NOT apply this product in a way that will contact workers or other persons, either directly or through drift. Only protected handlers may be in the area during application. For any requirements specific to your State or Tribe, consult the agency responsible for pesticide regulation. Windblown Soil Particles This product has the potential to move off-site due to wind erosion. Soils that are subject to wind erosion usually have a high silt and/or fine to very fine sand fractions and low organic matter content. Other factors which can affect the movement of windblown soil include the intensity and direction of prevailing winds, vegetative cover, site slope, rainfall, and drainage patterns. Avoid applying this product if prevailing local conditions may be expected to result in off-site movement. Non-target Organism Advisory This product is toxic to plants and may adversely impact the forage and habitat of non-target organisms, including pollinators, in areas adjacent to the treated area. Protect the forage and habitat of non-target organisms by minimizing spray drift. For further guidance and instructions on how to minimize spray drift, refer to the Spray Drift Management section of this label. USER SAFETY RECOMMENDATIONS USERS SHOULD: Wash hands before eating, drinking, chewing gum, using tobacco or using the toilet. 

ALLY® EXTRA herbicide must be used only in accordance with instructions on this label or in supplemental FMC publications. FMC will not be responsible for losses or damages resulting from the use of this product in any manner not specified by FMC. ALLY EXTRA herbicide is for use on wheat, barley, triticale and fallow in most states, check with your state extension service or Department of Agriculture before use, to be certain ALLY EXTRA herbicide is registered in your state. ALLY EXTRA herbicide is not registered for use in Alamosa, Conejos, Costilla, Rio Grande, and Saquache counties of Colorado unless use is directed otherwise by supplemental labeling. PRODUCT INFORMATION ALLY EXTRA herbicide is a dry flowable granule that is used for selective postemergence weed control in wheat (including durum), barley, triticale and fallow. The best control is obtained when ALLY EXTRA herbicide is applied to young, actively growing weeds. The degree and duration of control may depend on the following: • weed spectrum and infestation intensity • weed size at application • environmental conditions at and following treatment ALLY EXTRA herbicide is noncorrosive, nonflammable, nonvolatile, and does not freeze. ALLY EXTRA herbicide should be mixed in water and applied as a uniform broadcast spray (See Tank Mixtures and Mixing Instructions sections for use with Liquid Nitrogen Fertilizer Solutions). ENVIRONMENTAL CONDITIONS AND BIOLOGICAL ACTIVITY ALLY EXTRA herbicide is absorbed through the roots and foliage of plants, rapidly inhibiting the growth of susceptible weeds. One to three weeks after postemergence application to weeds (2 to 5 weeks for wild garlic), leaves of susceptible plants appear chlorotic, and the growing point subsequently di es. In warm, moist conditions, the expression of herbicide symptoms is accelerated; in cold, dry conditions, expression of herbicide symptoms is delayed. ALLY EXTRA herbicide will provide up to 4 to 6 weeks of residual weed control. Susceptible weeds may germinate and emerge a few days after postemergence applications, but growth then ceases and leaves become chlorotic 3- 5 days after emergence. Death of leaf tissue and growing point will follow in some species, while others will remain green but stunted and noncompetitive. ALLY EXTRA herbicide provides the best control of weeds in vigorously growing crops that shade competitive weeds. Weed control in areas of thin crop stand or seeding skips may not provide satisfactory control. However, a crop canopy that is too dense at application can intercept spray and reduce weed control. The herbicidal action of ALLY EXTRA herbicide may be less effective on weeds stressed from adverse environmental conditions (such as extreme temperatures or moisture), abnormal soil conditions, or cultural practices. In addition, weeds hardened-off by drought stress are less susceptible to ALLY EXTRA herbicide. PRODUCT MEASUREMENT ALLY EXTRA herbicide can be measured using the ALLY EXTRA herbicide volumetric measuring cylinder included in the case. The degree of accuracy of this cylinder varies by ± 7.5%. For more precise measurement, use scales calibrated in ounces. AGRICULTURAL USE REQUIREMENTS Use this product only in accordance with its labeling and with the Worker Protection Standard, 40 CFR part 170. This Standard contains requirements for the protection of agricultural workers on farms, forests, nurseries, and greenhouses, and handlers of agricultural pesticides. It contains requirements for training, decontamination, notification, and emergency assistance. It also contains specific instructions and exceptions pertaining to the statements on this label about personal protective equipment (PPE) and restricted-entry interval. The requirements in this box only apply to uses of this product that are covered by the Worker Protection Standard. Do not enter or allow worker entry into treated areas during th e restricted entry interval (REI) of 12 hours. PPE required for early entry to treated areas that is permitted under the Worker Protection Standard and that involves contact with anything that has been treated, such as plants, soil, or water, is: Coveralls. Chemical Resistant Gloves made of any waterproof material >14 mls. Shoes plus socks. 

RATE CONVERSION CHART FOR ALLY EXTRA HERBICIDE Ounces of ALLY EXTRA herbicide/A Pounds of ALLY EXTRA herbicide /A Active Ingredient Pounds of Active Ingredient/A 0.2 0.0125 Thifensulfuron methyl 0.0047 Tribenuron methyl 0.0023 Metsulfuron methyl 0.0019 0.21 0.0131 Thifensulfuron methyl 0.0049 Tribenuron methyl 0.0020 Metsulfuron methyl 0.0027 0.3 0.0188 Thifensulfuron methyl 0.0070 Tribenuron methyl 0.0035 Metsulfuron methyl 0.0028 0.31 0.0194 Thifensulfuron methyl 0.0073 Tribenuron methyl 0.0036 Metsulfuron methyl 0.0029 0.4 0.025 Thifensulfuron methyl 0.0094 Tribenuron methyl 0.0047 Metsulfuron methyl 0.0038 LABELLED USES ALLY EXTRA herbicide provides selective postemergence control of certain broadleaf weeds in wheat (including durum), barley, triticale, and fallow. Fallow Application and Use Rate Information Use Rates (oz of ALLY Extra herbicide per acre) Active Ingredient Pounds of Active Ingredient per acre Apply in the spring or fall when the majority of weeds have emerged and are actively growing. Apply 0.2 to 0.4 oz/A of ALLY EXTRA herbicide to fallow fields. ALLY EXTRA herbicide should be applied in combination with other suitable registered fallow herbicides (See TANK MIXTURES for additional information) 0.2 to 0.4 Thifensulfuron methyl 0.0047 to 0.0094 Tribenuron methyl 0.0023 to 0.0047 Metsulfuron methyl 0.0019 to 0.0038 RESTRICTIONS in Fallow: • ALLY EXTRA herbicide is only registered for use on wheat, barley, triticale and fallow. DO NOT use on any other crop. • DO NOT use less than 0.2 oz/A ALLY EXTRA herbicide. • DO NOT apply more than 0.4 oz/A of ALLY EXTRA herbicide in a single application (maximum active ingredient per single application is 0.0094 lb/A thifensulfuron methyl, 0.0047 lb/A tribenuron methyl, and 0.0038 lb/A metsulfuron methyl). • DO NOT apply more than 0.4 oz/A of ALLY EXTRA herbicide per year (maximum active ingredient per year of product is 0.0094 lb/A thifensulfuron methyl, 0.0047 lb/A tribenuron methyl, and 0.0038 lb/A metsulfuron methyl). 

TANK MIXTURES IN FALLOW ALLY EXTRA herbicide may be used as a fallow treatment an d should be tank mixed with other herbicides that are registered for use in fallow. Read and follow all manufacturers’ label instructions for the companion herbicide. If those instructions conflict with this label, DO NOT tank mix the herbicide with ALLY EXTRA herbicide. Wheat (Including Durum), Barley, and Triticale Application and Use Rate Information Use Rates (oz of ALLY Extra herbicide per acre) Active Ingredient Pounds of Active Ingredient per acre Apply ALLY EXTRA herbicide at the rate of 0.2 to 0.4 oz/A to wheat, barley, triticale or fallow. Use 0.4 oz/A of ALLY EXTRA herbicide for heavy infestation of the weeds listed under Weeds Partially Controlled when application timing and environmental conditions are marginal (refer to Biological Activity and Environmental Conditions section of this label for best performance). Use 0.2 to 0.3 oz/A of ALLY EXTRA herbicide for light infestation of the weeds listed under Weeds Controlled. Conditions at application should be optimum for effective treatment of these weeds. Note: See Tank Mix Section for additional info on required combinations when used at less than 0.4 oz/A. 0.2 to 0.4 Thifensulfuron methyl 0.0047 to 0.0094 Tribenuron methyl 0.0023 to 0.0047 Metsulfuron methyl 0.0019 to 0.0038 RESTRICTIONS in Wheat (including durum), Barley, and Triticale: • ALLY EXTRA herbicide is only registered for use on wheat, barley, triticale and fallow. DO NOT use on any other crop. • DO NOT apply to wheat, barley, or triticale crops undersown with legumes and grasses, because injury to the forages will result. • DO NOT harvest sooner than 45 days after the last application of ALLY EXTRA herbicide. • DO NOT use less than 0.2 oz/A ALLY EXTRA herbicide. • DO NOT apply more than 0.4 oz/A of ALLY EXTRA herbicide in a single application (maximum active ingredient per single application is 0.0094 lb/A thifensulfuron methyl, 0.0047 lb/A tribenuron methyl, and 0.0038 lb/A metsulfuron methyl). • DO NOT apply more than 0.4 oz/A of ALLY EXTRA herbicide per year (maximum active ingredient per year of product is 0.0094 lb/A thifensulfuron methyl, 0.0047 lb/A tribenuron methyl, and 0.0038 lb/A metsulfuron methyl). • PHI is 7 days for forage, 30 days for hay, and 45 days for wheat, barley and triticale. PRECAUTIONS in Wheat (including durum), Barley, and Triticale: Carefully observe all sprayer cleanup instructions both prior to and after using this product, as spray tank residue may damage crops other than wheat, barley, or triticale. ALLY EXTRA herbicide should not be applied to wheat, barley or triticale that is stressed by severe weather conditions, drought, low fertility, water-saturated soil, disease, or insect damage, as crop injury may result. Risk of injury is greatest when crop is in the 2 to 5- leaf stage. Severe winter stress, drought, disease, or insect damage following application also may result in crop injury. Varieties of wheat (including durum), barley and triticale may differ in their response to various herbicides. FMC recommends that you first consult your state experiment station, university, or extension agent as to sensitivity to any herbicide. If no information is available, limit the initial use of ALLY EXTRA herbicide to a small area. 

APPLICATION TIMING Fallow

• Apply in the spring or fall when the majority of weeds have emerged and are actively growing. Wheat (except Durum and Wampum varieties of Spring Wheat), Barley and Triticale
• DO NOT harvest sooner than 45 days after the last application of ALLY EXTRA herbicide.
• Make applications after the crop is in the 2-leaf stage, but before the flag leaf is visible. Durum and Wampum Variety Spring Wheat
• Make applications after the crop is tillering but before boot. Applications to durum and wampum varieties should be made in combination with 2,4-D.
• Weed control may be reduced if rainfall or snowfall occurs soon after application. Six hours of dry weather are needed to allow ALLY EXTRA herbicide to be sufficiently absorbed by weed foliage.
• If applied to irrigated wheat, barley or triticale the first post-treatment irrigation should be delayed for at least 6 hours after treatment and should not exceed 1 in. of water.
• DO NOT apply ALLY EXTRA herbicide to stressed crops, as this may cause crop injury. To reduce the potential of crop injury, tank mix ALLY EXTRA herbicide with 2,4-D (ester formulations perform best-see TANK MIXTURES) and apply after the crop is in the tillering stage of growth.
• Rainfall immediately after treatment can wash ALLY EXTRA herbicide off of weed foliage, resulting in reduced weed control. DO NOT apply ALLY EXTRA herbicide when rainfall is threatening.
• Add a FMC-recommended, nonionic surfactant having at least 80% active ingredient strength at 0.125 to 0.25% v/v (1 pt to 1 qt per 100 gal of spray solution).
• Antifoaming agents may be needed. Consult your Ag dealer, applicator, or FMC representative for a listing of recommended surfactants. WEEDS CONTROLLED ALLY EXTRA herbicide effectively controls the following weeds when used according to label directions: Annual knawel Annual sowthistle Black mustard Blue/Purple mustard * Broadleaf dock Bur buttercup (testiculate) Bushy wallflower/ Treacle mustard Canada thistle* Carolina geranium Clasping pepperweed Coast fiddleneck (tarweed) Common buckwheat Common chickweed Common cocklebur Common mallow Common Purslane Common radish Common ragweed Common sunflower * Conical Catchfly Corn chamomile Corn gromwell * Corn spurry Cowcockle Cress (mouse-ear) Curly dock Cutleaf eveningprimrose False chamomile Field chickweed Field pennycress (fanweed) Filaree (redstem, Texas) Flixweed * Groundsel (common) Henbit Kochia‡ Knotweed (prostrate) * Lambsquarter (common, slimleaf) London rocket Marshelder Mayweed chamomile Miners lettuce Narrowleaf lambsquarters Nightflowering catchfly Pennsylvania smartweed Pigweed (prostrate, redroot, smooth, tumble) Pineappleweed Plains coreopsis Prickly lettuce‡ Redmaids Russian thistle ‡ Scentless chamomile /mayweed Shepherd's-purse Smallflower buttercup Smallseed falseflax Smartweed (green, ladysthumb, pale) Snow Speedwell Sticky chickweed Stinking mayweed /dogfennel Swinecress Tansymustard * Tarweed fiddleneck Tumble/ Jim Hill mustard Volunteer lentils Volunteer peas Volunteer sunflower Waterpod Wild buckwheat * Wild chamomile Wild garlic * Wild mustard Wild radish * 

WEEDS PARTIALLY CONTROLLED** ALLY EXTRA herbicide partially controls the following weeds when used according to label directions: Catchweed bedstraw Mallow (little) Nightshade (cutleaf, hairy) Sowthistle (annual) * Tall waterhemp Vetch* (common, hairy)

• See the Specific Weed Problems section of this label for more information. **Partial control: A visual reduction of weed population as we ll as a significant loss of vigor. For better results, use the hi ghest labeled rate of ALLY EXTRA herbicide and include a tank mix partner such as 2,4-D, MCPA, bromoxynil (including Buctril® herbicide, Bronate® herbicide or Bronate Advanced™ herbicide) or dicamba (including Banvel® herbicide/ Clarity® herbicide), refer to the Tank Mixtur es section of this label. ‡ Naturally occurring resistant biotypes of kochia, prickly lettuce and Russian thistle are known to occur. See the Tank Mixtures and Specific Weed Problems sections of this label for additional details. TANK MIXTURES ALLY EXTRA herbicide may be tank mixed with other suitable registered herbicides to control weeds listed as partially controlled, weeds resistant to ALLY EXTRA herbicide or weeds not listed under Weeds Controlled. Read and follow all manufacturers label instructions for the companion herbicide. If those instructions conflict with this label, DO NOT tank mix the herbicide with ALLY EXTRA herbicide. ALLY EXTRA herbicide can also be mixed with registered fungi cides, insecticides, or liquid fertilizer for use on wheat, barley and triticale. To provide best results, ALLY EXTRA herbicide should be tank mixed with another broadleaf herbicide. For best results, use 2,4-D, or MCPA (preferably ester formulations). See below for use rates of 2,4-D or MCPA. With 2,4-D (amine or ester) or MCPA (amine or ester) ALLY EXTRA herbicide can be tank mixed with 2,4-D and MCPA (preferably ester formulations) herbicides for use on wheat, barley, triticale and fallow. For best results, add 2,4-D or MCPA herbicides to the tank at 1/8 to 3/8 lb active ingredient per acre. In tank mixes containing 1/8 lb active ingredient 2,4-D or MCPA per acre, add 1 to 2 pt of non-ionic surfactant per 100 gal of spray solution; in tank mixes containing 1/4 to 3/8 lb active ingredient 2,4-D or MCPA per acre, add 1 pt of non-ionic surfactant per 100 gal of spray solution. Higher rates of 2,4-D or MCPA may be used, but DO NOT exceed the highest rate allowed by those respective labels. Always mix ALLY EXTRA herbicide in water prior to adding 2,4-D or MCPA and add the surfactant last. Read and follow all label instructions on timing, precautions, and warnings for these herbicides before using these tank mixtures. With 2,4-D or MCPA (amine or ester) and dicamba (including Banvel® herbicide/Clarity® herbicide) ALLY EXTRA herbicide may be applied in a 3-way tank mix with formulations of dicamba (including Banvel® herbicide/ Clarity® herbicide) and 2,4-D or MCPA. Observe all applicable directions, restrictions and precautions on labels of all products used. Make applications of ALLY EXTRA herbicide + 1.0-1.5 oz active dicamba (including Banvel® herbicide/ Clarity® herbicide) + 1/4 to 3/8 lb active ingredient of 2,4-D or MC PA (ester or amine) per acre. Use higher rates when weed infestation is heavy. Add 1-2 pt of nonionic surfactant to the 3-way mixture, where necessary, as deemed by local guidance. Use of additional nonionic surfactant may not be needed with the higher phenoxy rates and ester phenoxy formulations. Consult the specific 2,4-D or MCPA and dicamba labels, or local guidance for more information. Apply this 3-way combination to winter wheat after the crop is tillering and prior to jointing (first node). In Spring Wheat (including Durum), apply after the crop is tillering and before it exceeds the 5-leaf stage. DO NOT apply this 3-way mixture at high rates more than once a year or more than twice per year at the low rates. With Bromoxynil containing products (including Buctril® herbicide, Bronate® herbicide or Bronate Advance™ herbicide) ALLY EXTRA herbicide may be tank mixed with bromoxynil containing herbicides registered for use on wheat, barley, triticale or fallow. For best results, add bromoxynil-containing herbicides to the tank at 3 to 6 oz active ingredient per acre (including Bronate® herbicide at 3/4 - 1 1/2 pt per acre). Tank mixes of ALLY EXTRA herbicide plus bromoxynil may result in reduced control of Canada thistle. Read and follow all label instructions on timing, precautions, and warnings for these herbicides before using these tank mixtures. Follow the most restrictive labeling. With fluroxypyr containing products (including “STARANE®” brands) For improved control of Kochia (2-4” tall) ALLY EXTRA herbicide may be tank mixed with fluroxypyr containing products. Refer to the FMC herbicide label and the “Starane®” branded product labels for information regarding use restrictions, labeled crops, rotational cropping intervals, sprayer cleanup, use precautions and other information. The most restrictive provisions on either label will apply. DO NOT use the tank mix if any restriction on the labels conflict with instructions on th e FMC herbicide label. 2,4-D and MCPA herbicides (preferably ester formulations) may be tank mixed with ALLY EXTRA herbicide plus fluroxypyr, consult local guidance and the Tank Mixtures section of this label for additional information. 

With Maverick® herbicide ALLY EXTRA herbicide can be tank mixed with Maverick® herbicide for improved control of weeds in wheat. Refer to the Maverick® label for information regarding use restrictions, labeled crops, rotational cropping intervals, sprayer cleanup, use precautions and other information. The most restrictive provisions on either label will apply. DO NOT use the tank mix if any restrictions on the Maverick® herbicide label conflict with instructions on the FMC herbicide label. With Aim® herbicide ALLY EXTRA herbicide can be tank mixed with Aim® herbicide for improved control of weeds in wheat, barley and triticale. Refer to the Aim® herbicide label for information regarding us e restrictions, labeled crops, rotational cropping intervals, sprayer cleanup, use precautions and other information. The most restrictive provisions on either label will apply. DO NOT use the tank mix if any restrictions on the Aim® herbicide label conflict with instructions on the FMC herbicide label. With Stinger® herbicide or Curtail® herbicide or Curtail® M herbicide or WideMatch® herbicide ALLY EXTRA herbicide can be tank mixed with Stinger® herbicide, Curtail® herbicide, Curtail® M herbicide, or WideMatch® herbicide for improved control of weeds in wheat, ba rley and triticale. Refer to the Stinger® herbicide, Curtail® herbicide, Curtail® M herbicide, and WideMatch® herbicide labels for information regarding use restrictions, labeled crops, rotational cropping intervals, sprayer cleanup, use precautions and other information. The most restrictive provisions on eithe r label will apply. DO NOT use the tank mix if any restrictions on the Stinger® herbicide or Curtail® herbicide or Curtail® M herbicide or WideMatch® herbicide labels conflict with instructions on the FMC herbicide label. With Puma® 1EC herbicide ALLY EXTRA herbicide can be tank mixed with Puma® 1EC herbicide for improved control of weeds in wheat, barley and triticale. Refer to the Puma® 1EC herbicide label for information regarding use restrictions, labeled crops, rotational cropping intervals, sprayer cleanup, use precautions and other information. The most restrictive provisions on either label will apply. DO NOT use the tank mix if any restrictions on the Puma® 1EC herbicide label conflict with instructions on the FMC herbicide label. With Discover® NG herbicide ALLY EXTRA herbicide can be tank mixed with Discover® NG herbicide for improved control of weeds in spring wheat. Refer to the Discover® NG herbicide label for information regarding use restrictions, labeled crops, rotational cropping intervals, sprayer cleanup, use precautions and other information. The most restrictive provisions on either label will apply. DO NOT use the tank mix if any restrictions on the Discover® NG herbicide label conflict with instructions on the FMC herbicide label. With “Everest®” branded herbicides ALLY EXTRA herbicide can be tank mixed with “Everest®” branded herbicides for improved control of weeds in spring wheat. Refer to the “Everest®” branded product label for information regarding use restrictions, labeled crops, rotational cropping intervals, sprayer cleanup, use precautions and other information. The most restrictive provisions on either label will apply. DO NOT use the tank mix if any restrictions on the “Everest®” branded product label conflict with instructions on the FMC herbicide label. With Other Herbicides ALLY EXTRA herbicide may be tank mixed with other suitable registered cereal or fallow herbicides to control weeds listed as suppressed, weeds resistant to ALLY EXTRA herbicide, or weeds not listed under Weeds Controlled. Read and follow all manufacturer’s label instructions for the companion herbicide. If those instructions conflict with this label, DO NOT tank mix the herbicide with ALLY EXTRA herbicide. Tank mixes of ALLY EXTRA herbicide plus metribuzin may result in reduced control of wild garlic. DO NOT tank mix ALLY EXTRA herbicide with Hoelon® 3EC herbicide, because grass control may be reduced. With Fungicides ALLY EXTRA herbicide may be tank mixed or used sequentially with fungicides registered for use on cereal crops. With Insecticides ALLY EXTRA herbicide may be tank mixed or used sequentiall y with insecticides registered for use on cereal crops. However, under certain conditions (drought stress, or if the crop is in the 2-4 leaf stage), tank mixes or sequential applicati ons of ALLY EXTRA herbicide with organophosphate insecticides may produce temporary crop yellowing or, in severe cases, crop injury. The potential for crop injury is greatest when wide fluctuations in day/night temperatures occur just prior to or soon after application. Test these mixtures in a small area before treating large areas. DO NOT apply ALLY EXTRA herbicide within 60 days of crop emergence where an organophosphate insecticide has been applied as an in-furrow treatment, because crop injury may result. DO NOT use ALLY EXTRA herbicide plus malathion containing products, as crop injury may result. 

With Liquid Nitrogen Fertilizer Solution Liquid nitrogen fertilizer solutions (e.g., 28-0-0, 32-0-0) may be used as a carrier in place of water. Run a tank mix compatibility test before mixing ALLY EXTRA herbicide in fertilizer solution. ALLY EXTRA herbicide must first be slurried with water and then added to liquid nitrogen solutions. Ensure that the agitator is running while the ALLY EXTRA herbicide is added. Use of this mixture may result in temporary crop yellowing and stunting. If using low rates of liquid nitrogen fertilizer in the spray solution (less than 50% of the spray solution volume), the additi on of surfactant is necessary. Add surfactant at 1/2 pt -1 qt pe r 100 gal of spray solution (0.06 -0.25% v/v) based on local guidance. When using high rates of liquid nitrogen fertilizer in the spray solution, adding surfactant increases the risk of crop injury. If 2,4-D or MCPA is included with ALLY EXTRA herbicide and fertilizer mixture, ester formulations tend to be more compatible (See manufacturer’s label). Additional surfactant may not be needed when using ALLY EXTRA herbicide in tank mix with 2,4-D ester or MCPA ester and liquid nitrogen fertilizer solutions. Consult your agricultural dealer, consultant, fiel d advisor, or FMC representative for specific instructions before adding an adjuvant to these tank mixtures. Note: In certain areas east of the Mississippi river unacceptable crop response may occur with use of straight or dilute nitrog en fertilizer carrier solutions wher e cold temperatures or widely fluctuating day/night temperatures exist. In these areas consult your agricultural dealer, consultant, field advisor, or FMC re presentative for specific instructions before using nitrogen fertilizer carrier solutions. DO NOT use low rates of liquid fertilizer as a substitute for a surfactant. DO NOT use with liquid fertilizer solutions with a pH less than 3.0. SPECIFIC WEED PROBLEMS Note: Thorough spray coverage of all weed species listed below is very important. Blue Mustard and Tansymustard: For best results, use 0.3-0.4 oz/A and apply ALLY EXTRA herbicide in tank mixtures with 2,4-D or MCPA postemergence to mustards, but before bloom (refer to Tank Mixtures section of this label for additional details). Flixweed: For best results, use 0.3-0.4 oz/A and apply ALLY EXTRA herbicide in tank mixtures with 2,4-D or MCPA postemergence, but before bloom (refer to Tank Mixtures section of this label for additional details). Canada Thistle: For best results, use 0.4 oz/A and apply ALLY EXTRA herbicide plus 2,4-D, or MCPA, or dicamba (including Banvel® herbicide/ Clarity® herbicide) (refer to Tank Mixtures for additional details) in the spring after the majority of thistles have emerged and are small (rosette stage to 6” elongating stems) and actively growing. The application will inhibit the ability of emerged thistles to compete with the crop. Sowthistle: For best results, use 0.4 oz/A and apply either ALLY EXTRA herbicide plus surfactant or ALLY EXTRA plus 2,4-D or MCPA (refer to Tank Mixtures section of this label for additional details) in the spring after the majority of sowthistles have emerged and are small (rosette stage to 6” elongating stems) and actively growing. Corn Gromwell: For best results, use 0.3-0.4 oz/A and apply ALLY EXTRA herbicide when weeds are actively growing, are no larger than 2” tall, and when crop canopy will allow thorough coverage. Tank mixing 2,4-D, MCPA, or bromoxynil containing products (including Buctril® herbicide, Bronate® herbicide, or Bronate Advanced™ herbicide) with ALLY EXTRA herbicide usually improves results (refer to Tank Mixtures section of this label for additional details). Sunflower (common/volunteer): For best results, use 0.4 oz/A and apply either ALLY EXTRA herbicide plus surfactant or ALLY EXTRA herbicide plus 2,4-D or MCPA (refer to Tank Mixt ures section of this label for additional details) after the majority of sunflowers have emerged, are 2” to 4” tall and are actively growing. Use spray volumes of at least 3 gal by air. Prostrate Knotweed: For best results, use 0.4 oz/A and apply ALLY EXTRA herbicide when weeds are actively growing, are no larger than 2” tall, and when crop canopy will allow thorough coverage. Tank mixing 2,4-D or MCPA (refer to Tank Mixtures section of this label for additional details) with ALLY EXTRA herbicide usually improves results. Wild Buckwheat: For best results, use 0.3-0.4 oz/A and apply ALLY EXTRA herbicide plus 2,4-D, MCPA, or bromoxynil containing products (including Buctril® herbicide, Bronate® herbicide, or Bronate Advanced™ herbicide) when plants have no more than three true leaves (not counting the cotyledons). If plants are not actively growing, delay treatment until environmental conditions favor active weed growth (refer to Tank Mixtures section of this label for additional details). Vetch (common and hairy): For best results, use 0.4 oz/A and apply ALLY EXTRA herbicide when vetch is less than 6” in length. For severe infestations of vetch, or when vetch is greater than 6” in length, use ALLY EXTRA herbicide in combination with 2,4- D, or MCPA (refer to Tank Mixtures section of this label for additional details). Wild garlic: For best results, use 0.4 oz/A and apply ALLY EXTRA herbicide when wild garlic plants are less than 12” tall with 2” to 4” of new growth. Plants hardened-off by cold weather and/or drought stress may be more difficult to control. Thorough spray coverage of all garlic plants is essential. Typical symptoms of dying garlic plants may not be noticeable for 2 to 5 weeks. Control will be improved by using ALLY EXTRA herbicide in combination with 2,4-D or MCPA (refer to Tank Mixtures section of this label for additional details).

Wild radish: For best results, use 0.4 oz/A applied in the fall to wild radish rosettes less than 6” in diameter and before plants harden-off. Alternatively, ALLY EXTRA herbicide can be applied in the spring for control of wild radish. Control will be improved by using ALLY EXTRA herbicide in combination with 2,4-D or MCPA (refer to Tank Mixtures section of this label for additional details) when wild radish rosettes are less than 6” in diameter. Applications made later than 30 days afte r weed emergence, either in the fall or spring, will result in partial control. Kochia, Russian thistle, Prickly lettuce: Naturally occurring resistant biotypes of these weeds are known to occur. For best results, use ALLY EXTRA herbicide in a tank mix with fluoxypyr containing products, bromoxynil containing products (including Buctril® herbicide, Bronate® herbicide, or Bronate Advanced™ herbicide) or dicamba (including Banvel® herbicide/ Clarity® herbicide) and/or 2,4-D (refer to Tank Mixtures section of this label for additional details). ALLY EXTRA herbicide should be applied in the spring when kochia, Russian thistle, and prickly lettuce are less than 2” tall or 2” across and are actively growing. SPRAY ADJUVANTS Include a spray adjuvant with applications of ALLY EXTRA herbicide in addition, an ammonium nitrogen fertilizer may be used. Consult your Ag dealer or applicator, local FMC fact sheets, technical bulletins, and service policies prior to using an adjuvant system. If another herbicide is tank mixed with ALLY EXTRA herbicide, select adjuvants authorized for use with both products. Products must contain only EPA-exempt ingredients (40CFR 1001). Nonionic Surfactant (NIS) żApply 0.06 to 0.50% volume/volume (1/2 pt to 4 pt per 100 gal of spray solution). żSurfactant products must contain at least 60% nonionic surfactant with a hydrophilic/lipophilic balance (HLB) greater than 12.– See the Tank Mixtures section of this label for additional information. Petroleum Crop Oil Concentrate (COC) or Modified Seed Oil (MSO) żApply at 1% volume/volume (1 gal per 100 gal spray solution) or 2% volume/volume under arid conditions. żOil adjuvants must contain at least 80% high quality, petroleum (mineral) or modified vegetable seed oil with at least 15% surfactant emulsifiers. Special Adjuvant Types żCombination adjuvant products may be used at doses that provide the required amount of NIS, COC, MSO and/or ammonium nitrogen fertilizer. Consult product literature for use rates and restrictions. żIn addition to the adjuvants specified above, other adjuvant types may be used if they provide the same functionality and have been evaluated and approved by FMC product management. Consult separate FMC technical bulletins for detailed information before using adjuvant types not specified on this label. Ammonium Nitrogen Fertilizer żUse 2 qt/acre of a high-quality urea ammonium nitrate (UAN), such as 28%N or 32%N, or 2 lb/acre of a spray-grade ammonium sulfate (AMS). Use 4 qt/acre UAN or 4 lb/acre AMS under arid conditions. GROUND APPLICATION For optimum spray distribution and thorough coverage, use flat-fan or low-volume flood nozzles. For flat-fan nozzles, use a spray volume of at least 5 gal per acre (GPA). For flood nozzles on 30” spacing, use flood nozzles no larger than TK10 (or the equivalent), a pressure of at least 30 psi and a spray volume of at least 10 GPA only. For 40” nozzle spacing, use at least 13 GPA; for 60” spacing use at least 20 GPA. It is essential to overlap the nozzles 100% for all spacings. “Raindrop RA” nozzles are not recommended for ALLY EXTRA herbicide applications, becaus e weed control performance may be reduced. Use screens that are 50-mesh or larger. AERIAL APPLICATION • Use nozzle types and arrangements that provide optimum spray distribution and maximum coverage at 1 to 5 GPA. • Use at least 3 GPA in Idaho, Oregon, Washington, or Utah. • DO NOT apply ALLY EXTRA herbicide by air in the state of New York. When applying ALLY EXTRA herbicide by air in areas near sens itive crops, use solid-stream nozzles oriented straight back. Adjust swath to avoid spray drift damage to downwind sensitive crops and/or ground equipment to treat border edge of field. See the Spray Drift Management section of this label. For aerial application in Washington, follow the directions in the Spray Drift Management Section of this label and the following Washington state restrictions: Applications of ALLY EXTRA herbicide must be made in equipment that meets the most restrictive Washington Agricultural Codes (WAC) for the prevention of herbicide drift for the respective county. DO NOT apply in equipment that does not meet these WAC standards. 

SEQUENTIAL APPLICATIONS ALLY EXTRA herbicide can be applied either before or after applications of other products registered for use in wheat, barley, triticale or fallow. Read and follow all label instructions on timing, precautions, and warnings for these herbicides before using these in sequence with ALLY EXTRA herbicide. If those instructions conflict with this label, DO NOT use that product in sequence with ALLY EXTRA herbicide. • DO NOT use any metsulfuron methyl-containing product as a sequential treatment with ALLY EXTRA herbicide. • If using HARMONY® EXTRA XP herbicide as a sequential treatment with ALLY EXTRA herbicide, DO NOT exceed 0.7 oz/A of HARMONY® EXTRA XP herbicide per year. • If using HARMONY® EXTRA SG herbicide (with TotalSol® soluble granules) as a sequential treatment with ALLY EXTRA herbicide, DO NOT exceed 1.0 oz/A of HARMONY® EXTRA SG herbicide per year. • If using EXPRESS® XP herbicide as a sequential treatment with ALLY EXTRA herbicide, DO NOT exceed 0.25 oz/A of EXPRESS® XP herbicide per year. • If using EXPRESS® herbicide (with TotalSol® soluble granules) as a sequential treatment with ALLY EXTRA herbicide, DO NOT exceed 0.375 oz/A of EXPRESS® herbicide per year. CROP ROTATION Before using ALLY EXTRA herbicide carefully consider your crop rotation plans and options. For rotational flexibility, DO NOT treat all of your acres at the same time. Minimum Rotational Intervals Minimum rotation intervals* are determined by the rate of breakdown of ALLY EXTRA herbicide applied. ALLY EXTRA herbicide breakdown in the soil is affected by soil pH, presence of soil microorganisms, soil temperature, and soil moisture. Low soil pH, high soil temperature, and high soil moisture increase ALLY EXTRA herbicide breakdown in soil, while high soil pH, low soil temperature, and low soil moisture slow ALLY EXTRA herbicide breakdown. Of these 3 factors, only soil pH remains relatively constant. Soil temperature, and to a greater extent, soil moisture, can var y significantly from year to year and from area to area. For this reason, soil temperatures and soil moisture should be monitored regularly when considering crop rotations.

• The minimum rotation interval represents the period of time from the last application to the anticipated date of the next planting. Minimum rotation intervals must be extended 1 crop season if drought conditions prevail after application and before the rotational crop is planted. Soil pH Limitations ALLY EXTRA herbicide should not be used on soils having a pH above 7.9, because extended soil residual activity could extend crop rotation intervals beyond normal. Under certain conditions, ALLY EXTRA herbicide could remain in the soil for 34 months or more, injuring wheat, barley or triticale. In addition, other crops planted in high-pH soils can be extremely sensitive to low concentrations of ALLY EXTRA herbicide. Checking Soil pH Before using ALLY EXTRA herbicide, determine the soil pH of the areas of intended use. To obtain a representative pH value for the test area, take several 0” to 4” samples from different areas of the field and analyze them separately. Consult local extension publications for additional information on recommended soil sampling procedures. 

All Areas - Following Use of ALLY EXTRA herbicide at 0.21 to 0.4 Ounces Per Acre Crop Soil pH Minimum Cumulative Precipitation (inches) Minimum Rotation Interval (months) Winter wheat, spring wheat and Triticale 7.9 or lower No restrictions 1 Durum wheat, barley, spring/winter oat 7.9 or lower No restrictions 10 Rotation Intervals For Crops in Non-Irrigated Land Following Use of ALLY EXTRA herbicide at 0.21 to 0.4 Ounces Per Acre on Wheat, Barley, Triticale or Fallow Location Crop Soil pH Minimum Cumulative Precipitation (inches) Minimum Rotation Interval (months) State County or Area Colorado Statewide Grain sorghum 7.9 or lower No restrictions 4 Flax, Safflower 7.9 or lower No restrictions 22 Generally N of I-70 Field corn 7.9 or lower 15 12 Statewide STS Soybean 7.9 or lower No restrictions 4 IR Corn 7.9 or lower No restrictions 4 Proso millet 7.9 or lower No restrictions 4 Idaho Southern Idaho Flax, Safflower 7.9 or lower No restrictions 22 Statewide Peas, Lentils, Canola 6.8 or lower 18 10 Peas 6.9 to 7.9 18 15 Lentils 6.9 to 7.9 18 34 Canola 6.9 to 7.9 18 22 Condiment mustard 7.3 or lower 10 10 Chickpeas (Garbanzo beans) 7.3 or lower 10 10 Condiment mustard 7.4 or higher 28 34 Chickpeas (Garbanzo beans) 7.4 or higher 28 34 Kansas Statewide STS Soybean 7.9 or lower No restrictions 4 IR Corn 7.9 or lower No restrictions 4 Proso millet 7.9 or lower No restrictions 4 Grain sorghum 7.9 or lower No restrictions 4 Flax, Safflower 7.9 or lower No restrictions 22 Central and Western Kansas (West of the Flint Hills) Field corn 7.9 or lower 15 12 Western Kansas W. of Hwy. 183 Soybeans 7.5 or lower 7.6–7.9 22 33 22 34 Central Kansas; generally E. of Hwy. 183 and W. of the Flinthills Soybeans 7.9 or lower 15 12 Montana Statewide Grain sorghum, Proso millet, Field corn 7.9 or lower 22 22 Alfalfa (hay only) 7.6–7.9 No restrictions 34 7.5 or lower No restrictions 22 Flax, Safflower 7.9 or lower No restrictions 22 Continued on next page 

Rotation Intervals For Crops in Non-Irrigated Land (continued) Following Use of ALLY EXTRA herbicide at 0.21 to 0.4 Ounces Per Acre on Wheat, Barley, Triticale or Fallow Location Crop Soil pH Minimum Cumulative Precipitation (inches) Minimum Rotation Interval (months) State County or Area Nebraska Statewide STS Soybean 7.9 or lower No restrictions 4 IR Corn 7.9 or lower No restrictions 4 Proso millet 7.9 or lower No restrictions 4 Grain sorghum 7.9 or lower No restrictions 4 Flax, Safflower 7.9 or lower No restrictions 22 Generally W. of Hwy. 77 and E. of the Panhandle Field corn 7.9 or lower 15 12 Soybeans 7.5 or lower 22 22 7.6-7.9 33 34 New Mexico Statewide Grain sorghum, Proso millet 7.9 or lower No restrictions 10 Flax, Safflower 7.9 or lower No restrictions 22 Eastern New Mexico Cotton (dryland only) 7.9 or lower 30 22 North Dakota W. of Hwy. 1 Grain sorghum, Proso millet, Field corn, Dry beans, Flax, Safflower 7.9 or lower 22 22 E. of Hwy. 1 Grain sorghum, Proso millet, Field corn, Dry beans, Flax, Safflower 7.9 or lower 34 34 Oklahoma Statewide STS So ybean 7.9 or lower No restrictions 4 IR Corn 7.9 or lower No restrictions 4 Proso millet 7.9 or lower No restrictions 4 Grain sorghum 7.9 or lower No restrictions 4 Flax, Safflower 7.9 or lower No restrictions 22 Field corn 7.9 or lower 15 12 Panhandle Cotton (dryland only) 7.9 or lower 30 22 E. of the Panhandle Cotton (dryland only) 7.9 or lower 25 14 Oregon Statewide Peas Lentils Canola 6.8 or lower 18 10 Peas 6.9 to 7.9 18 15 Lentils 6.9 to 7.9 18 34 Canola 6.9 to 7.9 18 22 Condiment mustard 7.3 or lower 10 10 Chickpeas (Garbanzo beans) 7.3 or lower 10 10 Condiment mustard 7.4 or higher 28 34 Chickpeas (Garbanzo beans) 7.4 or higher 28 34 South Dakota Statewide Flax, Safflower 7.9 or lower No restrictions 22 S. of Hwy. 212 & E. of the Missouri River, & S. of Hwy. 34 & W. of Missouri River Grain sorghum, Proso millet 7.9 or lower 13 12 Generally E. of Missouri River & S. of Hwy. 14, & W. of MissouriRiver Field corn 7.9 or lower 15 12 Continued on next page 

Rotation Intervals For Crops in Non-Irrigated Land (continued) Following Use of ALLY EXTRA herbicide at 0.21 to 0. 4 Ounces Per Acre on Wheat, Barley, Triticale or Fallow Location Crop Soil pH Minimum Cumulative Precipitation (inches) Minimum Rotation Interval (months)State County or Area Texas Statewide STS Soybeans 7.9 or lower No restrictions 4 IR Corn 7.9 or lower No restrictions 4 Proso millet 7.9 or lower No restrictions 4 Grain sorghum 7.9 or lower No restrictions 4 Flax, Safflower 7.9 or lower No restrictions 22 Panhandle Field corn 7.9 or lower 15 12 Cotton (dryland only) 7.9 or lower 30 22 N. Central Texas* Field corn 7.9 or lower 15 12 Cotton (dryland only) 7.9 or lower 25 14

• The counties of N. Central Texas are: Archer, Baylor, Bell, Bosque, Bowie, Callahan, Camp, Cass, Clay, Collin, Cooke, Coryell, Dallas, Delta, Denton , Eastland, Ellis, Falls, Fannin, Foard, Franklin, Grayson, Hardeman, Haskell, Hill, Hood, Hopkins, Hunt, Jack, Johnson, Kaufman, Knox, Lamar, Limestone, McLennan, Milam, Montague, Morris, Nafarro, Palo Pinto, Parker, Rains, Red River, Robertson, Rockwall, Shackelford, Somervell, Stephens, Tarrent, Throckmorton, Titus, Upshur, Van Zandt, Wilbarger, Wichita, Williamson, Wise, Wood, Young. Utah Statewide Flax, Safflower 7.9 or lower No restrictions 22 Washington Statewide Condiment mustard 7.3 or lower 10 10 Chickpeas (Garbanzo beans) 7.3 or lower 10 10 Condiment mustard 7.4 or higher 28 34 Chickpeas (Garbanzo beans) 7.4 or higher 28 34 Peas Lentils Canola 6.8 or lower 18 10 Peas 6.9 to 7.9 18 15 Lentils 6.9 to 7.9 18 34 Canola 6.9 to 7.9 18 22 Wyoming Statewide Flax, Safflower 7.9 or lower No restrictions 22 Southern Wyoming Grain sorghum, Proso millet 7.9 or lower No restrictions 10 Southern Wyoming (Goshen, Laramie, and Platte counties only) Field corn 7.9 or lower 15 12 Northern Wyoming Grain sorghum, Proso millet, Field corn 7.9 or lower 22 22 Rotation Intervals for crops not covered above - The minimum rotation interval is 34 months with at least 28” of cumulative precipitation during the period: • to any major field crop not listed (See the Rotation Intervals table) • if the soil pH is not in the specified range • if the use rate applied is not specified in the table • or if the minimum cumulative precipitation has not occurred since application. To rotate to a major field crop at an interval shorter than specified, a field bioassay must be successfully completed to that crop. A field bioassay must be successfully completed before rotation to any minor crops (as determined by the USDA criteria). See section on Field Bioassay for further information. 

Rotation Intervals For Crops in Non-Irrigated Land Following Use of ALLY EXTRA herbicide up to 0.3 Ounces Per Acre on Wheat, Barley, Triticale or Fallow in the states of Colorado, Kansas, Nebraska, New Mexico, Oklahoma, South Dakota, Texas and Wyoming Crop Soil pH Minimum Cumulative Precipitation (inches) Minimum Rotation Interval (months) Sunflower 7.9 or lower No restrictions 10 Rotation Intervals for crops not covered above (up to 0.3 ounces per acre) - The minimum rotation interval is 34 months with at least 28” of cumulative precipitation during the period: • to any major field crop not listed (See the Rotation Intervals table) • if the soil pH is not in the specified range • if the use rate applied is not specified in the table • or if the minimum cumulative precipitation has not occurred since application. To rotate to a major field crop at an interval shorter than specified, a field bioassay must be successfully completed to that crop. A field bioassay must be successfully completed before rotation to any minor crops (as determined by the USDA criteria). See section on Field Bioassay for further information. Rotation Intervals For Crops in Non-Irrigated Land Following Use of ALLY EXTRA herbicide at 0.31 to 0.4 Ounces Per Acre on Wheat, Barley, Triticale or Fallow Location Crop Soil pH Minimum Cumulative Precipitation (inches) Minimum Rotation Interval (months)State County or Area Colorado Idaho Kansas Montana Nebraska New Mexico Oklahoma South Dakota Texas Utah Wyoming Statewide Sunflower 7.9 or lower No restrictions 22 North Dakota W. of Hwy. 1 Sunflower 7.9 or lower 22 22 E. of Hwy. 1 Sunflower 7.9 or lower 34 34 Rotation Intervals for crops not covered above (0.31 to 0.4 ounces per acre) - The minimum rotation interval is 34 months with at least 28” of cumulative precipitation during the period: • to any major field crop not listed (See the Rotation Intervals table) • if the soil pH is not in the specified range • if the use rate applied is not specified in the table • or if the minimum cumulative precipitation has not occurred since application. To rotate to a major field crop at an interval shorter than specified, a field bioassay must be successfully completed to that crop. A field bioassay must be successfully completed before rotation to any minor crops (as determined by the USDA criteria). See section on Field Bioassay for further information. 

Rotation Intervals For Crops in Non-Irrigated Land Following Use of ALLY EXTRA herbicide at 0.2 Ounces Per Acre on Wheat, Barley Triticale or Fallow Crop Soil pH Minimum Cumulative Precipitation (inches) Minimum Rotation Interval (months) Sorghum, Grain 7.9 or lower No restrictions 4 Cotton 7.9 or lower No restrictions 10 Safflower 7.9 or lower No restrictions 10 Peas, Dry /Green 6.8 or lower No restrictions 10 6.9 to 7.9 No restrictions 22 Lentils 6.8 or lower No restrictions 10 6.9 to 7.9 No restrictions 22 Alfalfa 6.8 or lower No restrictions 10 6.9 to 7.9 No restrictions 22 Beans, Dry 6.8 or lower No restrictions 10 6.9 to 7.9 No restrictions 22 Sunflower 7.9 or lower No restrictions 10 Rotation Intervals for crops not covered above (0.2 ounces per acre) - The minimum rotation interval is 22 months with at least 18” of cumulative precipitation during the period: • to any major field crop not listed (See the Rotation Intervals table) • if the soil pH is not in the specified range • if the use rate applied is not specified in the table • or if the minimum cumulative precipitation has not occurred since application. To rotate to a major field crop at an interval shorter than specified, a field bioassay must be successfully completed to that crop. A field bioassay must be successfully completed before rotation to any minor crops (as determined by the USDA criteria). See section on Field Bioassay for further information. FIELD BIOASSAY A field bioassay is necessary if crops other than wheat, barley or those listed on this label are to be planted on land previously treated with ALLY EXTRA herbicide. To conduct a field bioassay, grow test strips of the crop or crops you plan to grow the following year in fields previously treated with ALLY EXTRA herbicide. Crop response to the bioassay will indicate whether or not to rotate to the crop(s) grown in the test strips. If a field bioassay is planned, check with your local FMC representative for information detailing field bioassay procedure. GRAZING Allow at least 7 days between application and grazing of treated forage. In addition, allow at least 7 days between application and feeding of forage from treated areas to livestock. Allow at least 30 days between application and feeding of hay from treated areas to livestock. Harvested straw may be used for bedding and/or feed. Allow at least 45 days between application and harvesting of grain. MIXING INSTRUCTIONS

1. Fill the tank 1/4 to 1/3 full of water.
2. While agitating, add the required amount of ALLY EXTRA herbicide.
3. Continue agitation until the ALLY EXTRA herbicide is fully dispersed, at least 5 minutes.
4. Once the ALLY EXTRA herbicide is fully dispersed, maintain agitation and continue filling tank with water. ALLY EXTRA herbicide should be thoroughly mixed with water before adding any other material.
5. As the tank is filling, add tank mix partners (if desired) then add the required volume of surfactant. Always add surfactant last. Antifoaming agents may be used. DO NOT use with spray additives that alter the pH of the spray solution below pH 5.0 or above pH 9.0 as rapid product degradation can occur. Spray solutions of pH 6.0 - 8.0 allow for optimum stability of ALLY EXTRA herbicide.
6. If the mixture is not continuously agitated, settling will occur. If settling occurs, thoroughly reagitate beforeusing.
7. Apply ALLY EXTRA herbicide spray mixture within 24 hours of mixing to avoid product degradation.
8. If ALLY EXTRA herbicide and a tank mix partner are to be applied in multiple loads, pre-slurry the ALLY EXTRA herbicide in clean water prior to adding to the tank. This will prevent the tank mix partner from interfering with the dispersion of ALLY EXTRA herbicide. 

SPRAY EQUIPMENT For specific application equipment, refer to the manufacturer’s instructions for additional information on GPA, pressure, speed, nozzle types and arrangements, nozzle heights above the target canopy, etc. Be sure to calibrate air or ground equipment properly before application. Select a spray volume and delivery system that will ensure thorough coverage and a uniform spray pattern with minimum drift. Use higher spray volumes to obtain better coverage when crop canopy is dense. Avoid swath overlapping, and shut off spray booms while starting, turning, slowing, or stopping, to avoid injury to the crop. DO NOT make applications using equipment and/or spray volumes or during weather conditions that might cause spray to drift onto nontarget sites. For additional information on spray drift refer to Spray Drift Management section of label. Continuous agitation is required to keep ALLY EXTRA herbicide in suspension. SPRAYER CLEANUP The spray equipment must be cleaned before ALLY EXTRA herb icide is sprayed. Follow the cleanup procedures specified on the labels of the previously applied products. If no directions are provided, follow the six steps outlined in the After Spraying ALLY EXTRA herbicide section of this label. AT THE END OF THE DAY It is recommended that during periods when multiple loads of ALLY EXTRA herbicide are applied, at the end of each day of spraying the interior of the tank be rinsed with fresh water and then partially filled, and the boom and hoses flushed. This wi ll prevent the buildup of dried pesticide deposits which can accumulate in the application equipment. AFTER SPRAYING ALLY EXTRA HERBICIDE AND BEFORE SPRAYING CROPS OTHER THAN WHEAT, BARLEY OR TRITICALE To avoid subsequent injury to desirable crops, thoroughly clean all mixing and spray equipment immediately following applications of ALLY EXTRA herbicide as follows:

1. Drain tank; thoroughly rinse spray tanks, boom, and hoses with clean water. Loosen and physically remove any visible deposits.
2. Fill the tank with clean water and 1 gal of household ammonia* (contains 3% active ingredient) for every 100 gal of water. Flush the hoses, boom, and nozzles with the cleaning solution. Then add more water to completely fill the tank. Circulate the cleaning solution through the tank and hoses for at least 15 min. Flush the hoses, boom, and nozzles again with the cleaning solution, and then drain the tank.
3. Remove the nozzles and screens and clean separately in a bucket containing cleaning agent and water.
4. Repeat step 2.
5. Rinse the tank, boom, and hoses with clean water.
6. If only ammonia is used as a cleaner, the rinsate solution may be applied back to the crop(s) specified on this label. DO NOT exceed the maximum labeled use rate. If other cleaners are used, consult the cleaner label for rinsate disposal instructions. If no instructions are given, dispose of the rinsate on site or at an approved waste disposal facility.

• Equivalent amounts of an alternate-strength ammonia solution or an FMC-approved cleaner can be used in the cleanout procedure. Carefully read and follow the individual cleaner instructions. Consult your Ag dealer, applicator, or FMC representative for a listing of approved cleaners. Notes:

1. CAUTION: DO NOT use chlorine bleach with ammonia because dangerous gases will form. DO NOT clean equipment in an enclosed area.
2. Steam-cleaning aerial spray tanks is recommended prior to performing the above cleanout procedure to facilitate th e removal of any caked deposits.
3. When ALLY EXTRA herbicide is tank mixed with other pesticides, cleanout procedures for each product should be examined and the most rigorous procedure should be followed.
4. In addition to this cleanout procedure, all pre-cleanout guidelines on subsequently applied products should be followed as per the individual product labels.
5. Where routine spraying practices include shared equipment frequently being switched between applications of ALLY EXTRA herbicide and applications of other pesticides to ALLY EXTRA herbicide-sensitive crops during the same spray season, it is recommended that a sprayer be dedicated to ALLY EXTRA herbicide to further reduce the chance of crop injury. 

SPRAY DRIFT MANAGEMENT ADVISORIES THE APPLICATOR IS RESPONSIBLE FOR AVOIDING OFF-SITE SPRAY DRIFT. BE AWARE OF NEARBY NON-TARGET SITES AND ENVIRONMENTAL CONDITIONS. IMPORTANCE OF DROPLET SIZE An effective way to reduce spray drift is to apply large droplets. Use the largest droplets that provide target pest control. While applying larger droplets will reduce spray drift, the potential for drift will be greater if applications are made improperly or under unfavorable environmental conditions. Controlling Droplet Size – Ground Boom • Volume - Increasing the spray volume so that larger droplets are produced will reduce spray drift. Use the highest practical spray volume for the application. If a greater spray volume is needed, consider using a nozzle with a higher flow rate. • Pressure - Use the lowest spray pressure recommended for the nozzle to produce the target spray volume and droplet size. • Spray Nozzle - Use a spray nozzle that is designed for the in tended application. Consider using nozzles designed to reduce drift. Controlling Droplet Size – Aircraft • Adjust Nozzles - Follow nozzle manufacturers recommendations for setting up nozzles. Generally, to reduce fine droplets, nozzles should be oriented parallel with the airflow in flight. BOOM HEIGHT – Ground Boom Use the lowest boom height that is compatible with the spray nozzles that will provide uniform coverage. For ground equipment, the boom should remain level with the crop and have minimal bounce. RELEASE HEIGHT - Aircraft Higher release heights increase the potential for spray drift. When applying aerially to crops, DO NOT release spray at a heigh t greater than 10 ft above the crop canopy, unless a greater application height is necessary for pilot safety. SHIELDED SPRAYERS Shielding the boom or individual nozzles can reduce spray drift. Consider using shielded sprayers. Verify that the shields are not interfering with the uniform deposition of the spray on the target area. MANDATORY SPRAY DRIFT MANAGEMENT Ground Boom Applications: • Apply with the nozzle height recommended by the manufacturer, but no more than 3 feet above the ground or crop canopy. • For applications prior to the emergence of crops and target weeds, applicators are required to use a Coarse or coarser droplet size (ASABE S572.1). • For all other applications, applicators are required to use a Medium or coarser droplet size (ASABES572.1). • DO NOT apply when wind speeds exceed 10 miles per hour at the application site. • DO NOT apply during temperature inversions. Boom-less Ground Applications: • Applicators are required to use a Medium or coarser droplet size (ASABE S572.1) for all applications. • DO NOT apply when wind speeds exceed 10 miles per hour at the application site. • DO NOT apply during temperature inversions. Aerial Applications: • DO NOT release spray at a height greater than 10 feet above the vegetative canopy, unless a greater application height is necessary for pilot safety. • For applications prior to the emergence of crops and target weeds, applicators are required to use a Coarse or coarser droplet size (ASABE S572.1). • For all other applications, applicators are required to use a Medium or coarser droplet size (ASABES572.1). • The boom length must not exceed 65% of the wingspan for airplanes or 75% of the rotor blade diameter for helicopters. • Applicators must use one-half swath displacement upwind at the downwind edge of the field. • Nozzles must be oriented so the spray is directed toward the back of the aircraft. • DO NOT apply when wind speeds exceed 10 miles per hour at the application site. • DO NOT apply during temperature inversions. 

TEMPERATURE AND HUMIDITY When making applications in hot and dry conditions, use larger droplets to reduce effects of evaporation. TEMPERATURE INVERSIONS Drift potential is high during a temperature inversion. Temper ature inversions are characterized by increasing temperature with altitude and are common on nights with limited cloud cover and light to no wind. The presence of an inversion can be indicated by ground fog or by the movement of smoke from a ground source or an aircraft smoke generator. Smoke that layers and moves laterally in a concentrated cloud (under lo w wind conditions) indicates an inversion, while smoke that moves upward and rapidly dissipates indicates good vertical air mixing. Avoid applications during temperature inversions. WIND Drift potential generally increases with wind speed. AVOID APPLICATIONS DURING GUSTY WIND CONDITIONS. Applicators need to be familiar with local wind patterns and terrain that could affect spray drift. Handheld Technology Applications: • Take precautions to minimize spray drift. Boom-less Ground Applications • Setting nozzles at the lowest effective height will help to reduce the potential for spray drift. SENSITIVE AREAS The pesticide may only be applied when the potential for drift to adjacent sensitive areas (e.g., residential areas, bodies of water, known habitat for threatened or endangered species, non-target crops) is minimal (e.g. when wind is blowing away from the sensitive areas). DRIFT CONTROL ADDITIVES Using product compatible drift control additives can reduce drift potential. When a drift control additive is used, read and carefully observe cautionary statements and all other information on the additive’s label. If using an additive that increases viscosity, ensure that the nozzles and other application equipment will function properly with a viscous spray solution. Preferred drift control additives have been certified by the Chemical Producers and Distributors Association (CPDA). WEED RESISTANCE MANAGEMENT ALLY EXTRA herbicide, which contains the active ingredients Metsulfuron methyl, Thifensulfuron methyl and Tribenuron methyl, is a group 2 herbicide based on the mode of action classification system of the Weed Science Society ofAmerica. Proactively implementing diversified weed control strategies to minimize selection for weed populations resistant to one or more herbicides is a best practice. A diversified weed management program may include the use of multiple herbicides with different sites of action and overlapping weed spectrum with or without tillage operations and/or other cultural practices. Research has demonstrated that using the labeled rate and directions for use is important to delay the selection for resistance. The continued effectiveness of this product depends on the successful implementation of a weed resistance management program. To aid in the prevention of developing weeds resistant to this product, users should: • Scout fields before application to ensure herbicides and rates will be appropriate for the weed species and weed sizes present. • Start with a clean field, using either a burndown herbicide application or tillage. • Control weeds early when they are relatively small (less than 4 inches). • Apply full rates of ALLY EXTRA herbicide for the most difficult to control weed in the field at the specified time (correct weed size) to minimize weed escapes. • Scout fields after application to detect weed escapes or shifts in control of weedspecies. • Control weed escapes before they reproduce by seed or proliferate vegetatively. • Report any incidence of non-performance of this product ag ainst a particular weed to your FMC representative, local retailer, or county extension agent. • Contact your FMC representative, crop advisor, or extension agent to find out if suspected resistant weeds to these MOAs have been found in your region. DO NOT assume that each listed weed is being controlled by multiple sites of action. Products with multiple active ingredients are intended to broaden the spectrum of weeds that are controlled. Some weeds may be controlled by only one of the active ingredient in this product. • If resistance is suspected, treat weed escapes with an herb icide having a site of action other than Group 2 and/or use nonchemical methods to remove escapes, as practical, with the goal of preventing further seed production. • Suspected herbicide-resistant weeds may be identified by these indicators:

• Failure to control a weed species normal ly controlled by the herbicide at the dose applied, especially if control is achieved on adjacent weeds;
• A spreading patch of non-controlled plants of a particular weed species; and
• Surviving plants mixed with controlled individuals of the same species. 

Additionally, users should follow as many of the following herbicide resistance management practices as is practical: • Use a broad spectrum soil-applied herbicide with other sites of action as a foundation in a weed control program. • Utilize sequential applications of herbicides with alternative sites ofaction. • Rotate the use of this product with non-Group 2 herbicides. • Avoid making more than two applications of ALLY EXTRA herbicide and any other Group 2 herbicides within a single growing season unless mixed with an herbicide with a different site of action with an overlapping spectrum for the difficult-to- control weeds. • Incorporate non-chemical weed control practices, such as mech anical cultivation, crop rotation, cover crops and weed-free crop seeds, as part of an integrated weed control program. • Use good agronomic principles that enhance crop development and crop competitiveness. • Thoroughly clean plant residues from equipment before leaving fields suspected to contain resistant weeds. • Manage weeds in and around fields, during and after harvest to reduce weed seedproduction. INTEGRATED PEST MANAGEMENT FMC recommends the use of Integrated Pest Management (IPM) programs to control pests. This product may be used as part of an Integrated Pest Management (IPM) program which can include biological, cultural, and genetic practices aimed at preventing economic pest damage. Application of this product should be based on IPM principles and practices including field scouting or other detection methods, correct target pest identification, population monitoring, and treating when target pest populations reach locally determined action thresholds. Consult your state cooperative extension service, professional consultants or other qualified authorities to determine appropriate action treatment threshold levels for treating specific pest/crop systems in your area. RESTRICTIONS AND PRECAUTIONS • ALLY EXTRA herbicide is only registered on wheat, barley, triticale and fallow. DO NOT use on any othercrop. • DO NOT apply this product through any type of irrigation equipment or to irrigated land where tailwater will be used to irrigate crops other than wheat, barley or triticale. • Varieties of wheat (including durum), barley and triticale may differ in their response to various herbicides. FMC recommends that you first consult your state experiment station, university, or extension agent as to sensitivity to any herbicide. If no information is available, limit the initial use of ALLY EXTRA herbicide to a small area. • Under certain conditions such as heavy rainfall, prolonged cold weather, or wide fluctuations in day/night temperatures prior to or soon after ALLY EXTRA herbicide application, temporary discoloration and/or crop injury may occur. To reduce the potential of crop injury, tank mix ALLY EXTRA herbicide with 2,4-D (ester formulations perform best–see the Tank Mixtures section of this label) and apply after the crop is in the tillering stage of growth. • ALLY EXTRA herbicide should not be applied to wheat, barley or triticale that is stressed by severe weather conditions, drought, low fertility, water-saturated soil, disease, or insect damage, as crop injury may result. Risk of injury is greatest when crop is in the 2 to 5- leaf stage. Severe winter stress, drought, disease, or insect damage following application also may result in crop injury. • DO NOT apply to wheat, barley or triticale undersown with legu mes and grasses, because injury to the forages will result. • For ground applications applied when dry, dusty field conditions exist, control of weeds in wheel track areas may be reduced. The addition of 2,4-D or MCPA may improve weed control under these conditions. • Injury to or loss of desirable trees or vegetation may result from failure to observe the following:

• DO NOT apply, drain or flush equipment on or near desirable trees or other plants or on areas where their roots may extend, or in locations where the chemical may be washed or moved into contact with their roots.
• DO NOT use on lawns, walks, driveways, tennis courts, or similar areas. Prevent drift of spray to desirable plants. • Injury to or loss of adjacent sensitive crops and vegeta tion may result from failure to observe the following:
• Take all necessary precautions to avoid all direct or indirect contact (such as spray drift) with non-target plants or areas.
• Carefully observe all sprayer cleanup instructions both prior to and after using this product, as spray tank residue may damage crops other than wheat, barley or triticale. 

When using ALLY EXTRA herbicide in tank mixes or sequential applications with other products containing metsulfuron methyl, thifensulfuron methyl, and/or tribenuron methyl, DO NOT exceed the following limits: Use Area Application Timing Maximum Product oz/A per Single Application Active Ingredient Maximum AI oz/A per Single Application Maximum AI oz/A per Cropping Cycle & per Year For All Applications Maximum AI oz/A per Year Max # of Cropping Cycles Maximum Number of Applications per Cropping Cycle & Year Pre-Harvest Interval, Days Fallow Spring or fall when the majority of weeds have emerged and are actively growing. Post harvest, fallow, spring or fall. 0.40 Metsulfuron Methyl 0.06 0.06 0.06 12 N A Thifensulfuron Methyl 0.15 0.15 0.75 Tribenuron Methyl 0.075 0.075 0.50 Wheat, barley, triticale After 2-leaf stage but before flag leaf is visible 0.40 Metsulfuron Methyl 0.06 0.06 0.06 12 Allow at least 7 days between application and grazing of treated forage. In addition, allow at least 7 days between application and feeding of forage from treated areas to livestock. Allow at least 30 days between application and feeding of hay from treated areas to livestock. Harvested straw may be used for bedding and/or feed. Allow at least 45 days between application and harvesting of grain. Thifensulfuron Methyl 0.15 0.15 0.75 Tribenuron Methyl 0.075 0.075 0.50 Durum and Wampum Variety Spring Wheat After tillering but before boot. 0.40 Metsulfuron Methyl 0.06 0.06 0.06 12 Allow at least 7 days between application and grazing of treated forage. In addition, allow at least 7 days between application and feeding of forage from treated areas to livestock. Allow at least 30 days between application and feeding of hay from treated areas to livestock. Harvested straw may be used for bedding and/or feed. Allow at least 45 days between application and harvesting of grain. Thifensulfuron Methyl 0.15 0.15 0.75 Tribenuron Methyl 0.075 0.075 0.50 

IDENTIFICATION INFORMATION FOR PRODUCTS REFERENCED IN THIS LABEL IDENTIFICATION FOR PRODUCTS REFERENCED IN THIS LABEL REGISTERED PRODUCTS REFERENCED IN THIS LABEL FOR TANK MIXTURES OR MENTIONED FOR OTHER REASONS Product Name Active Ingredient(s) EPA Registration Number Discover® NG Herbicide Clodinafop-propargyl 100-1173 Buctril® Herbicide Bromoxynil 264-437 Bronate® Herbicide Bromoxynil + MCPA 264-438 Hoelon® 3EC Herbicide Diclofop-methyl 264-641 Puma® 1EC Herbicide Fenoxaprop-p-ethyl 264-666 Bronate Advanced™ Herbicide Bromoxynil + MCPA 264-690 Clarity® Herbicide Dicamba 7969-137 Colt® + Sword® Herbicide (Starane® + Sword Herbicide, Starane® + MCPA Herbicide) Fluroxypyr + MCPA 34704-1011 Maverick® Herbicide Sulfosulfuron 59639-223 Curtail® Herbicide 2,4-D + Clopyralid 62719-48 Stinger® Herbicide Clopyralid 62719-73 Curtail® M Herbicide Clopyralid + MCPA 62719-86 WideMatch® Herbicide Clopyralid + Fluroxypyr 62719-512 Starane® NXT Herbicide Bromoxynil + Fluroxypyr 62719-557 Starane® Ultra Herbicide Fluroxypyr 62719-577 Starane® Flex Herbicide Florasulam + Fluroxypyr 62719-604 Banvel® Herbicide Dicamba 66330-276 Everest® 2.0 Herbicide Flucarbazone-sodium 66330-391 Banvel® 480 Herbicide Dicamba 66330-421 Everest® 3.0 Herbicide Flucarbazone-sodium 66330-429 Everest® 3.0 AG Flucarbazone-sodium 66330-433 

STORAGE AND DISPOSAL Do not contaminate water, food or feed by storage or disposal. Pesticide Storage: Store product in original container only. Pesticide Disposal: Do not contaminate water, food, or feed by disposal. Wastes resulting from the use of this product must be disposed of on site or at an approved waste disposal facility. Container Handling: Refer to the Net Co ntents section of this product’s labe ling for the applicable “Nonrefillable Container” or “Refillable Container” designation. Nonrefillable Plastic and Metal Containers (Capacity Equal to or Less Than 50 Pounds): Nonrefillable container. Do not reuse or refill this container. Triple rinse container (or equivalent) promptly after emptying. Triple rinse as follows: Empty the remaining contents into application equipment or a mix tank. Fill the container 1/4 full with water and recap. Shake for 10 seconds. Pour rinsate into ap plication equipment or a mix tank or stor e rinsate for later use or disposal. Drain for 10 seconds after the flow begins to drip. Repeat this pro cedure two more times. Then, for Plastic Containers, offer for recycling if available or puncture and dispose of in a sanitary landfill, or by incineration. Do not burn, unless allowed by state and local ordinances. For Metal Containers, offer for r ecycling if available or reconditioning if appropriate, or puncture and dispose of in a sanitary landfill, or by other procedures approved by state and local authorities. Nonrefillable Plastic and Metal Containers (Capacity Greater Than 50 Pounds): Nonrefillable container. Do not reuse or refill this container. Triple rinse container (or equivalent) promptly after emptying. Triple rinse as follows: Empty the remaining contents into application equipment or a mix tank. Fill the container 1/4 full with water. Replace and tighten closures. Tip container on its side and roll it back and forth, ensuring at least one complete revolution, for 30 seconds. Stand the container on its end and tip it back and forth several times. Turn the container over onto its other end and tip it back and forth several times. Empty the rinsate into applicatio n equipment or a mix tank or store rinsate for later use or disposal. Repeat this procedure two more times. Then, for Plas tic Containers, offer for recycling if available or puncture and dispose of in a sanitary landfill, or by incineration. Do not burn, unless allowed by state and local ordinances. For Metal Containers, offer for recycling if available or reconditioning if appropriate, or puncture and dispose of in a sanitary landfill, or by other procedures approved by state and local authorities. Nonrefillable Plastic and Metal Containers, e.g., Intermedia te Bulk Containers [IBC] (Size or Shape Too Large to be Tipped, Rolled or Turned Upside Down): Nonrefillable container. Do not reuse or refill this container. Clean container promptly after emptying the contents from this cont ainer into application equipment or mix tank and before final disposal using the following pressure rinsing procedure. Insert a lance fitted with a suitable tank cleaning nozzle into the container and ensure that the water spray thoroughly covers the top, bottom and all sides inside the container. The nozzle manufacturer generally provides instructions for the appropriate spray pressure, spray duration and/or spray volume. If the manufacturer’s instructions are not available, pressure rinse the container for at least 60 seconds using a minimum pressure of 30 PSI with a minimum rinse volume of 10% of the container volume. Drain, pour or pump rinsate into application equipment or rinsate collection system. Repeat this pressure rinsing procedure two more times. Then, for Plastic Containers, offer for recycling if available or puncture and dispose of in a sanitary landfill, or by incineration. For Metal Containers, offer for recycling if available or reconditioning if appropriate, or puncture and dispose of in a sanitary landfil l, or by other procedures approved by state and local authorities. Nonrefillable Paper or Plastic Bags, Fiber Sacks including Fl exible Intermediate Bulk Containers (FIBC) or Fiber Drums With Liners: Nonrefillable container. Do not reuse or refill this container. Completely empty paper or plastic bag, fiber sack or drum liner by shaking and tapping sides and bottom to loosen clinging particles. Empty residue into application or manufacturing equipment. Then offer for recycling if available or dispose of empty paper or plastic bag, fiber sack or fiber drum and liner in a sanitary landfill, or by incineration. Do not burn, unless allowed by state and local ordinances. Refillable Fiber Drums With Liners: Refillable container (fiber drum only). Refilling Fiber Drum: Refill this fiber drum with ALLY EXTRA herbicide containing thifensulfuron methyl, tribenuron methyl and metsulfuron methyl only. Do not reuse this fiber drum for any other purpose. Cleaning before refilling is the responsibility of the refiller. Completely empty liner by shaking and tapping sides and bottom to loosen clinging particles. Empty residue into application or manufacturing equipment. Disposing of Fiber Drum and/or Liner: Do not reuse this fiber drum for any other purpose other than refilling (see preceding). Cleaning the container (liner and/or fiber drum) before final disposal is the responsibility of the person disposing of the container. Offer the liner for recycling if available or dispose of liner in a sanitary landfill, or by incineration. Do not burn, unless allowed by state and local ordinances. If drum is contaminated and cannot be reused, dispose of it in the manner required for its liner. To clean the fiber drum before final disposal, completely empty the fiber drum by shaking and tapping sides and bottom to loosen clinging particles. Empty residue into application or manufacturing equipment. Then offer the fiber drum for recycling if available or dispose of in a sanitary landfill, or by incineration. Do not burn, unless allowed by state and local ordinances. All Other Refillable Containers: Refillable container. Refilling Container: Refill this container with ALLY EXTRA herbicide containing thifensulfuron methyl, tribenuron methyl and metsulfuron methyl only. Do not reuse this container for any other purpose. Cleaning before refilling is the responsibility of the refiller. Prior to refilling, inspect carefully for damage such as cracks, punctures, abrasions, worn out threads and closure devices. If damage is found, do not use the container, contact FMC at the number below for instructions. Check for leaks after refilling and before transporting. If leaks are found, do not reuse or transport container, contact FMC at the number below for instructions. Disposing of Container: Do not reuse this container for any other purpose other than refilling (see preceding). Cleaning the container before final disposal is the responsibility of the pers on disposing of the container. To clean the container before final disposal, use the following pressure rinsing procedure. Insert a lance fitted with a suitable tank cleaning nozzle into the container and ensure that the water spray thoroughly covers the top, bottom and all sides inside the container. The nozzle manufacturer generally provides instructions for the appropriate spray pressure, spray duration and/or spray 

NOTICE TO BUYER: Purchase of this material does not confer any rights under patents of countries outside of the United States. FMC, Ally®, Aim®, Express®, Harmony®, and TotalSol® are trademarks of FMC Corporation or an affiliate. “Maverick” is a registered trademark of Valent U.S.A. LLC “Clarity” is a registered trademark of BASF Corporation “Buctril”, “Bronate”, “Bronate Advanced”, “Hoelon”, and “Puma” are registered trademarks of Bayer Crop Science “Starane”, “Stinger”, “Curtail”, “Curtail M”, and “Widematch” are registered trademarks of Corteva Agriscience United States “Colt + Sword” is a registered trademark of UAP Loveland Products Inc. “Discover” is a registered trademark of Syngenta Crop Protection LLC “Banvel” and “Everest” are registered trademarks of Arysta LifeScience North America LLC “Raindrop RA” is a registered trademark of Delavan D - 4021 120319 volume. If the manufacturer’s instructions are not available, pressure rinse the container for at least 60 seconds using a minimum pressure of 30 PSI with a minimum rinse volume of 10% of the container volume. Drain, pour or pump rinsate into application equipment or rinsate collection system. Repeat this pressure rinsing procedure two more times. Then, for Plastic Containers, offer for recycling if available or puncture and dispose of in a sanitary landfill, or by incineration. Do not burn, unless allowed by state and local ordinances. For Metal Containers, offer for recycling if available or reconditioning if appropriate, or puncture and dispose of in a sanitary landfill, or by other procedures approved by state and local authorities. Outer Foil Pouches of Wat er Soluble Packets (WSP): Nonrefillable container. Do not reuse or refill this container. Offer for recycling if available or, dispose of the empty outer foil pouch in the trash as long as WSP is unbroken. If the outer pouch contacts the formulated product in any way, the pouch must be triple rinsed with clean water. Add the rinsate to the spray tank and dispose of the outer pouch as described previously. Do not transport if this container is damaged or leaking. If th e container is damaged, leaking or obsolete, or in the event of a major spill, fire or other emergency, contact CHEMTREC (Transportation and Spills) at 1-800-424-9300, day ornight. 

CONDITIONS OF SALE AND LIMITATION OF WARRANTY AND LIABILITY Notice: Read the entire Directions for Use and Conditions of Sale and Limitation of Warranty and Liability before buying or using this product. If the terms are not acceptable, return the product at once, unopened, and the purchase price will be refunded. The Directions for Use of this product must be followed carefully. It is impossible to eliminate all risks inherently associated with the use of this product. Crop injury, ineffectiveness, or other unintended consequences may result because of such factors as manner of use or application, weather or crop conditions beyond the control of FMC or Seller. To the extent consistent with applicable law, all such risks shall be assumed by Buyer and User, and, to the extent consistent with applicable law, Buyer and User agree to hold FMC and Seller harmless for any claims relating to such factors. Seller warrants that this product conforms to the chemical description on the label and is reasonably fit for the purposes stated on the Directions for Use when used in accordance with the directions under normal conditions of use. TO THE EXTENT CONSISTENT WITH APPLICABLE LAW, FMC MAKES NO WARRANTIES OF MERCHANTABILITY OR OF FITNESS FOR A PARTICULAR PURPOSE, NOR ANY OTHER EXPRESS OR IMPLIED WARRANTIES WITH RESPECT TO THE SELECTION, PURCHASE, OR USE OF THIS PRODUCT. Any warranties, express or implied, having been made are inapplicable if this product has been used contrary to label instructions, or under abnormal conditions, or under conditions not reasonably foreseeable to (or beyond the control of) Seller or FMC, and, to the extent permitted by applicable law, Buyer assumes the risk of any such use. To the extent consistent with applicable law, FMC or Seller shall not be liable for any incidental, consequential or special damages resulting from the use or handling of this product. TO THE EXTENT CONSISTENT WITH APPLICABLE LAW, THE EXCLUSIVE REMEDY OF THE USER OR BUYER, AND THE EXCLUSIVE LIABILITY OF FMC AND SELLER FOR ANY AND ALL CLAIMS, LOSSES, INJURIES OR DAMAGES (INCLUDING CLAIMS BASED ON BREACH OF WARRANTY, CONTRACT, NEGLIGENCE, TORT, STRICT LIABILITY OR OTHERWISE) RESULTING FROM THE USE OR HANDLING OF THIS PRODUCT, SHALL BE THE RETURN OF THE PURCHASE PRICE OF THE PRODUCT OR, AT THE ELECTION OF FMC OR SELLER, THE REPLACEMENT OF THE PRODUCT. This Condition of Sale and Limitation of Warranty and Liability may not be amended by any oral or written agreement. FMC Corporation, 2929 Walnut Street, Philadelphia, PA 19104 © 2001-2019 FMC Corporation. All rights reserved.