crop-chem-docs/corpus/epa_ppls/279-9619.md

DPX-SBN49 HERBICIDE (WITH TOTALSOL SOLUBLE GRANULES)

• EPA Reg No: 279-9619
• Registrant: FMC CORPORATION
• Signal word: Caution
• Active ingredients: Thifensulfuron (10%); Tribenuron-methyl (40%)
• Label accepted: 2019-07-15
• Source PDF: https://www3.epa.gov/pesticides/chem_search/ppls/000279-09619-20190715.pdf

---

July 15,2019 Subject: Dear Mr. Ambrose: Reg Review Label Acceptable v.20151230 OFFICE OF CHEMICAL SAFETY AND POLLUTION PREVENTION A copy of your label stamped “Accepted” is enclosed. Products shipped after 12 months from the date of this amendment must bear the new revised label. Your release for shipment of the product bearing the amended label constitutes acceptance of these conditions. If these conditions are not complied with, the registration will be subject to cancellation in accordance with FIFRA section 6. Registration Review Label Mitigation for Tribenuron methyl and Thifensulfuron methyl Product Name: DPX-SBN49 Herbicide (With TotalSol Soluble Granules) Application Date: 12/13/17 EPA Registration Number: 279-9619 Decision Number: 540709; 553176 The Agency, in accordance with the Federal Insecticide, Fungicide and Rodenticide Act (FIFRA), as amended, has completed reviewing all of the information submitted with your application to support the Registration Review of the above referenced product in connection with the 22 Sulfonylurea (SU) Herbicides Interim Decision, and has concluded that your submission is acceptable. The label referred to above, submitted in connection with registration under FIFRA, as amended, is acceptable. Should you wish to add/retain a reference to the company’s website on your label, then please be aware that the website becomes labeling under the Federal Insecticide Fungicide and Rodenticide Act and is subject to review by the Agency. If the website is false or misleading, the product would be misbranded and unlawful to sell or distribute under FIFRA section 12(a)(1)(E). 40 CFR 156.10(a)(5) list examples of statements EPA may consider false or misleading. In addition, regardless of whether a website is referenced on your product’s label, claims made on the website may not substantially differ from those claims approved through the registration process. Therefore, should the Agency find or if it is brought to our attention that a website contains false or misleading statements or claims substantially differing from the EPA approved registration, the website will be referred to the EPA’s Office of Enforcement and Compliance. Richard Ambrose FMC Corporation c/o FMC Stine Research Center P.O. Box 30 Newark, Delaware 19714-0030 UNITED STATES ENVIRONMENTAL PROTECTION AGENCY WASHINGTON, DC 20460 w

Sincerely, Enclosure If you have any questions about this letter, please contact Erik Kraft by phone at 703-308-9358, or via email at kraft.erik@epa.gov. Page 2 of 2 EPAReg. No. 279-9619 Decision No. 540709; 553176 Erik Kraft, Product Manager 24 Fungicide and Herbicide Branch Registration Division (7505P) Office of Pesticide Programs

ACCEPTED 07/15/2019 DPX-SBN49 279-9619 OR IF ON SKIN OR CLOTHING: Sold By -FMC 1 FMC Corporation 2929 Walnut Street Philadelphia, PA 19104 2 2 EPA Reg. No. 279-9619 EPA Est. No. Contains 0.50 lb active ingredient per pound (tribenuron methyl 0.40 and thifensulfuron methyl 0.10) GROUP GROUP HERBICIDE HERBICIDE KEEP OUT REACH OF CHILDREN CAUTION Si usted no entiende la etiqueta. busque a alguien para que se la explique a usted en detalle. (If you do not understand the label, find someone to explain it to you in detail.) HERBRICIDE (WITH TOTALSOL® SOLUBLE GRANULES) TRIBENURON METHYL THIFENSULFURON METHYL Nonrefillable Containers Net: Refillable Containers Net: Un<3er ibe Federal insecCicade. FuHiglclde arid RcdeiiOcide Act as aroended, lor the pesiljcide iregistered urider EPA. Reg. No. FIRST AID_______________________________ Take off contaminated clothing. Rinse skin immediately withplentyofwaterfor 15-20nimutes. Callapoison control center or doctor for treatmentadvice.__________ HOTLINE NUMBER __________________________ Have theproduct container or label with you whencallingapoison control center, doctor or goingfor treatment. ___You may also contact 1-800-331-3148 for emergency medical treatment information. PRECAUTIONARY STATEMENT HAZARD TO HUMANS AND DOMETIC ANIMALS CAUTION Prolonged or frequently repeated skin contact may cause allergic reactions in some individuals. Avoid contact with skin, eyes or clothing. Wash thoroughly with soap and water after handling and before eating, drinking, chewing gum, or using tobacco or using the toilet. Remove and wash contaminated clothing before reuse. For medical emergencies involving this product, call toll free 1-800-331-3148. SOLUBLE GRANULE For Use on Cereals, Fallow and as a Pre-plant or Post-harvest Burndown Herbicide Active Ingredients_____________________By Weight Tribenuron methyl 40% Thifensulfuron methyl 10% Other Ingredients 50% TOTAL 100%

USE SAFETY RECOMMENDATIONS 2 Groundwater Advisory This product is known to leach through soil into groundwater under certain conditions as a result of label use. This product may leach into groundwater if used in areas where soils are permeable, particularly where the water table is shallow. Surface Water Advisory This product may impact surface water quality due to runoff of rain water. This is especially true for poorly draining soils and soils with shallow ground water. This product is classified as having high potential for reaching surface water via runoff for several weeks or more after application. A level, well-maintained vegetative buffer strip between areas to which this product is applied and surface water features such as ponds, streams, and springs will reduce the potential loading of this product from runoff water and sediment. Runoff of this product will be greatly reduced by avoiding applications when rainfall or irrigation is expected to occur within 48 hours. Windblown Soil Particles Advisory This product has the potential to move off-site due to wind erosion. Soils that are subject to wind erosion usually have a high silt and/or fine to very fine sand fractions and low organic matter content. Other factors which can affect the movement of windblown soil include the intensity and direction of prevailing winds, vegetative cover, site slope, rainfall, and drainage patterns. Avoid applying this product if prevailing local conditions may be expected to result in off-site movement. Non-target Organism Advisory This product is toxic to plants and may adversely impact the forage and habitat of non-target organisms, including pollinators, in areas adjacent to the treated area. Protect the forage and habitat of non-target organisms by minimizing spray drift. For further guidance and instructions on how to minimize spray drift, refer to the Spray Drift Management section of this label. USERS SHOULD: • Wash hands before eating, drinking, chewing gum, using tobacco or using the toilet. • Remove clothing/PPE immediately if pesticide gets inside. Then wash thoroughly and put on clean clothing. • Remove PPE immediately after handling this product. Wash the outside of gloves before removing. As soon as possible, wash thorou^ly and change into clean clothing. PERSONAL PROTECTIVE EQUIPMENT (PPE) Applicators and other handlers must wear: • Long-sleeved shirt and long pants. • Chemical resistant gloves made of any waterproof material including polyethylene or polyvinyl chloride. • Shoes plus socks. Follow manufacturer's instructions for cleaning/maintainingPPE. If no such instructions for washables exists, use detergent and hot water. Keep and wash PpE separately from other laundry. Engineering Control Statements: When handlers use closed systems, enclosed cabs, or aircraft in a manner that meets the requirements listed in the Worker Protection Standard (WPS) for agricultural pesticides (40 CFR 170.240(d)(4-6), the handler PPE requirements may be reduced or modified as specified in the WPS. IMPORTANT: When reduced PPE is worn because a closed system is being used, handlers must be provided all PPE specified above for "applicators and other handlers" and have such PPE immediately available for use in an emergency, such as a spill or equipment break-down. ENVIRONMENTAL HAZARDS DO NOT apply directly to water, or to areas where surface water is present, or to intertidal areas below the mean highwater mark. DO NOT contaminate water when cleaning equipment or disposing of equipment washwaters or rinsate.

PESTICIDE HANDLING notification, and emergency assistance. It also contains specific instructions and exceptions pertaining to the statements on this labd about personal protective equipment (PPE) and restricted-entry interval. The requires or water, is: 3 DPX-SBN49 herbicide (with TotalSol® soluble granules), referred to below as DPX-SBN49 herbicide, must be used only in accordance with instructions on this label or as otherwise permitted by FIFRA. To the extent consistent with applicable law, FMC will not be responsible for losses or damages resulting from the use of this product in any manner not specified by FMC. Check with your state extension service or Department of Agriculture before use, to be certain DPX-SBN49 herbicide is registered in your state. Always read the entire label, including the Conditions of Sale and Limitation of Warranty and Liability. • Calibrate sprayers only with clean water away from well sites. • Make scheduled checks of spray equipment. • Ensure that all operation employees accurately measure pesticides. • Mix only enough product for the job at hand. • Avoid overfiUmgofspraytank. • DO NOT discharge excess material on the soil at a single spot in the field, grove, or mixing/loading station. • Dilute and agitate excess solution and apply at labeled rates or uses. • Avoid storage of pesticides near well sites. • When triple-rinsing the pesticide container, be sure to add the rinsate to the spray mix. Coveralls. Chemical resistant gloves made of any waterproof material. Shoes plus socks. PR OD UCT IN FORMA TION DPX-SBN49 herbicide is a water soluble granule that is used for selective postemergence weed control in wheat (including durum), barley, triticale, oats and for post-harvest bumdown, fallow, and pre-plant bumdown weed control. The best control is obtained when DPX-SBN49 herbicide is applied to young, actively growing weeds. The use rate will depend on weed spectrum and size ofweedattime of application. The degree and duration of control may depend on the weed spectrum and infestation intensity, weed size at application, and environmental conditions at and following treatment. DPX-SBN49 herbicide is noncorrosive, nonflammable, nonvolatile, and does not freeze. DPX-SBN49 herbicide needs to be mixed in water and applied as auniform broadcast spray. DIRECTION FOR USE It is a violation of Federal law to use this product in a manner inconsistent with its labeling, DO NOT apply this product in a way that will contact workers or other persons, either directly or through drift. Only protected handlers may be in the area during application. For any requirements specific to your State or Tribe, consult the agency responsible forpesticideregulation. itry into treated areas during the restricted entry interval (REI) required for early entry to treated areas that is permitted under the Worker Protection Stanc contact with anything that has been treated, such as plants, soil. AGRICULUTUAL USE REQUIREMENTS Use this product only in accordance with its labeling and with the Worker Protection Standard, 40 CFR part 170. This Standard contams requirements for the protection of agricultural workers on farms, forests, nurseries, and greenhouses, and handlers of agricultural pesticides. It contains requirements for training, decontamination, notification, and emergency assistance. It also contains specific instructions and exceptions pertaining to the statements on this labd about personal protective equipment (PPE) and restncted-ent^’ interval. The requirements in this box only apply to uses of this product that are covered by the Worker Protection Standard. Do not enter or allow worker entry into treated areas during the restricted entry interval (REI) of 12 hours. PPE otection Standard and that involves

4 BIOLOGICAL ACTIVITY AND ENVIRONMENTAL CONDITIONS DPX-SBN49 herbicide is absorbed through the foliage of broadleaf weeds, rapidly inhibiting their growth. Leaves of susceptible plants appear chlorotic from 1 to 3 weeks after application and the growing point subsequently dies. DPX-SBN49 herbicide provides the best control in vigorously growing crops that shade competitive weeds. Weed control in areas of thin crop stand or seeding skips may not be as satisfactory. However, a crop canopy that is too dense at application can intercept spray and reduce weed control. DPX-SBN49 herbicide may injure crops that are stressed from adverse environmental conditions (including extreme temperatures or moisture), abnormal soil conditions, or cultural practices. In addition, different varieties of the crop may have differing levels of sensitivity to treatment withDPX-SBN49 herbicide under otherwise normal conditions. Treatment of sensitive crop varieties may injure crops. To reduce the potential of crop injury to cereals, tank mix DPX-SBN49 herbicide with 2,4-D (ester formulations perform best-see the Tank Mixtures section of this label) and apply after the crop is in the tillering stage of growth. It is the pesticide user’s responsibility to ensure that all products are registered for the intended use. Read and follow the applicable restrictions and limitations and directions for use on all product labels involved in tank mixing. Users must follow the most restrictive directions for use and precautionary statements of each product in the tank mixture. If the instructions on the tank mix partner label conflicts with this DPX-SBN49 herbicide label, DO NOT use in a tank mixture with DPX-SBN49 herbicide. In warm, moist conditions, the expression of herbicide symptoms is accelerated in weeds; in cold, dry conditions, expression of herbicide symptoms is delayed. In addition, weeds hardened-off by drought stress are less susceptible to DPX-SBN49 herbicide. DPX-SBN49 herbicide is rainfast in 4 hours. RESTRICTIONS • Do not apply to wheat, barley, oats or triticale underseeded with another crop. • Do not apply this product through any type of irrigation system, • Injury to or loss of desirable trees or vegetation may result from failure to observe the following;

• Do not apply, drain or flush equipment on or near desirable trees or other plants or on areas where their roots may extend, or in locations where the chemical may be washed or moved into contact with their roots.
• Do not use on lawns, walks, driveways, crtennis courts. Prevent drift of spray to desirable plants. • WhenusingDPX-SBN49 herbicide in tank mixes or sequential applications with otherproducts containing tribenuron-methyl and thifensulfuron-methyl, do not exceed the following limits:
• For all uses the maximum active ingredient for tribenuron methyl is 0.0313 lb ai/A per year.
• For all uses the maximum active ingredient for thifensulfuron methyl is 0.0469 lb ai/A per year. PRECAUTIONS • Injury to or loss of adjacent sensitive crops and vegetation may result from failure to observe the following:
• Take all necessary precautions to avoid all direct or indirect contact (including spray drift) with non-target plants or areas.
• Carefully observe all sprayer cleanup instructions both prior to and after using this product, as spray tank residue may damage crops other than wheat or barley. • Varieties of wheat (including durum), barley, oats and triticale may differ in their response to various herbicides. FMC advices that you first consult your state experiment station, university, or extension agent as to crop sensitivity to any herbicide. If no information is available, limit the initial use to a small area. • Under certain conditions including heavy rainfall, prolonged cold weather, or wide fluctuations in day/night temperatures prior to or soon after DPX-SBN49 herbicide application, temporary discoloration and/or crop injury may occur. To reduce the potential of crop injiuy, tank mix DPX-SBN49 herbicide with 2,4-D (ester formulations perform best - see the "TANK MIXTURES" section of this label) and apply after the crop is in the tillering stage of growth. It is the pesticide user’s responsibility to ensure that all products are registered for the intended use. Read and follow the applicable restrictions and limitations and directions for use on all product labels involved in tank mixing. Users must follow the most restrictive directions for use and precautionary statements of each product in the tank mixture. If the instructions on the tank mix partner label conflicts with this DPX-SBN49

5 herbicide label, DO NOT use in a tank mixture with DPX-SBN49 herbicide. • DPX-SBN49 herbicide may not be applied to wheat, barley, oats or triticale that is stressed by severe weather conditions, drought, low fertility, water-saturated soil, disease, or insect damage, as crop injury may result. Risk of injury is greatest when crop is in the 2 to 5- leaf stage. Severe winter stress, drought, disease, or insect damage following application also may result in crop injury. WEED RESISTANCE MANAGEMENT DPX-SBN49 herbicide, which contains the active ingredients tnbenurou-methyl and ihifensulfiiron-methyl is a group 2 herbicide based on the mode of action classification system of the Weed Science Society of America. Proactively implementing diversified weed control strategies to minimize selection for weed populations resistant to one or more herbicides is a best practice, A diversified weed management program may include the use of multiple herbicides with different sites of action and overlapping weed spectrum with or without tillage operations and/or other cultural practices. Research has demonstrated that using the labeled rate and directions for use is important to delay the selection for resistance. The continued effectiveness of this product depends on the successful implementation of a weed resistance management program. To aid in the prevention of developing weeds resistant to this product, users should; • Scout fields before application to ensure herbicides and rates will be appropriate for the weed species and weed sizes present. • Start with a clean field, using either a bumdown herbicide application or tillage. • Control weeds early when they are relatively small (less than 4 inches). • Apply full rates of DPX-SBN49 herbicide for the most difficult to control weed in the field at the specified time (correct weed size) to minimize weed escapes. • Scout fields after application to detect weed escapes or shifts in control of weed species. • Control weed escapes before they reproduce by seed or proliferate vegetatively. • Report any incidence of non-performance of this product against a particular weed to your FMC representative, local retailer, or county extension agent. • Contact your FMC representative, crop advisor, or extension agent to find out if suspected resistant weeds to these MO As have been found in your region, DO NOT assume that each listed weed is being controlled by multiple sites of action. Products with multiple active ingredients are intended to broaden the spectrum of weeds that are controlled. Some weeds may be controlled by only one of the active ingredients in this product. • If resistance is suspected, treat weed escapes with an herbicide having a site of action other than Group 2 and/or use nonchemical methods to remove escapes, as practical, with the goal of preventing further seed production. • Suspected herbicide-resistant weeds may be identified by these indicators: Failure to control a weed species normally controlled by the herbicide at the dose applied, especially if control is achieved on adjacent weeds; A spreading patch of non-controlled plants of a particular weed species; and Surviving plants mixed with controlled individuals of the same species. Additionally, users should follow as many of the following herbicide resistance management practices as is practical; • Use a broad spectrum soil-applied herbicide with other sites of action as a foundation in a weed control program. • Utilize sequential applications of herbicides with alternative sites of action. • Rotate the use of this product with non-Group 2 herbicides. • Avoid making more than two applications of DPX-SBN49 herbicide and any other Group 2 herbicides within a single growing season unless mixed with an herbicide with a different site of action with an overlapping spectrum for the difficult-to-control weeds. • Incorporate non-chemical weed control practices, such as mechanical cultivation, crop rotation, cover crops and weed-free crop seeds, as part of an integrated weed control program. • Use good agronomic principles that enhance crop development and crop competitiveness. • Thoroughly clean plant residues from equipment before leaving fields suspected to contain resistant weeds. • Manage weeds in and around fields, during and after harvest to reduce weed seed production.

6 LABEL USES WHEAT, BARLEY, OATSAND TRITICALE APPLICATION TIMING Apply DPX-SBN49 herbicide after the crop is in the 2-leaf stage, but before the flag leaf is visible. For spring oats, make applications after the crop is in the 3-leaf stage, but before jointing. DO NOT use on "Ogle", "Porter" or "Premier" varieties as crop injury can occur. Since DPX-SBN49 herbicide has very little or no soil activity, it controls only those weeds that have germinated; therefore, apply DPX-SBN49 herbicide when all or most of the weeds have germinated. Annual broadleaf weeds need to be past the cotyledon stage, actively growing, and less than 4" tall or wide. DO NOT harvest within 45 days of the last application. CEREAL USE RATE Use 0.6 oz DPX-SBN49 herbicide per acre (except oats) for heavy infestation of those weeds listed under the "WEEDS CONTROLLED" section of this label or when application timing and environmental conditions are marginal (see "BIOLOGICAL ACTIVITY AND ENVIRONMENTAL CONDITIONS"). Use 0.3 to 0.6 oz DPX-SBN49 herbicide per acre (except oats) for light infestation of the weeds listed under the "WEEDS CONTROLLED" section of this label. Conditions at application need to be optimum for effective treatment of these weeds. Two applications of DPX-SBN49 herbicide may be made per yearprovided the total amount does not exceed 0.6 oz per acre. Allow at least 14 days between treatments._______________________________________________ DPX-SBN49 herbicide (oz/A) For oats, apply 0.25 oz of DPX-SBN49 herbicide per acre for control of light populations of the weeds listed in Weeds Controlled table. In oats, DPX-SBN49 herbicide must be tank mixed with another registered herbicide. DO NOT make more than one application of DPX- SBN49 herbicide per \earon oats.____________________ Tribenuron-methyl (Lb ai/A) 0.0063 Tribenuron-methyl (Lb ai/A) 0.0075-0.015 0.015 Thifensulfuron-methyl (Lb ai/A 0.0019-0.0038 0.0038 Thifensulfuron-methyl (Lb ai/A 0.0016 INEGRA TED PEST MANGEMENT This product may be used as part of an Integrated Pest Management (IPM) program that can include biological, cultural, and genetic practices aimed at preventing economic pest damage. IPM principles and practices include field scouting or other detection methods, correct target pest identification, population monitoring, and treating when target pest populations reach locally determined action thresholds. Consult your state cooperative extension service, professional consultants or other qualified authorities to determine appropriate action treatment threshold levels for treating specific pest/crop systems in your area. DPX-SBN49 herbicide (oz/A) 0.25 0.3-0.6 0.6

RESTRICTIONS Use Area 0.015 0.015 14 0.6 2 0.6 0.0038 0.0038 14 0.015 0.015 14 0.6 2 0.6 0.0038 0.0038 14 0.015 0.015 14 0.6 2 0.6 0.0038 0.0038 14 0.0063 0.0063 Spring Oats 0.25 1 0.25 0.0016 0.0016 7 Winter Wheat (combination with phenoxy tank mix partners) Spring Wheat (combination with phenoxy tank mix partners) Thifensulfuron -methyl Thifensulfuron -methyl Thifensulfuron -methyl Tribenuron- methyl Tribenuron- methyl Tribenuron- methyl Application Timing Maximum Number of Applications per Year Maximum Oz/A of Product per Year Wheat (including Durum, Barley, Triticale Thifensulfuron -methyl Tribenuron- methyl Maximum Oz/A of Product per Single Application DPX-SBN49 herbicide may be used as a bumdown treatment when the majority of weeds have emerged and are actively growing. DPX-SBN49 herbicide may be applied to crop stubble, as a fallow treatment, or as a pre­ plant bumdown prior to planting any crop. See "CROP ROTATION" for the minimum interval allowed between the bumdown application and when a crop may be planted. BURNDOWN-POST HARVEST, FALLOW, PRE-PLANT APPLICATION TIMING Maximum Lb Al/A of Product per Year 45 (for grain) 45 (for grain) 45 (for grain) 45 (for grain) Minimum Treatment Interval (Days) Not applicable Not applicable Maximum Lb Al/A per Single Application Pre­ Harvest Interval, Days Active Ingredient (Al) Postemerge nee: Apply in the 2-leaf stage but before the flag is visible Postemerge nee: Apply after the crop is tillering & prior to Jointing (first node) Postemerge nee: Apply after the crop is tillering & before it exceeds the 5-leaf stage Postemerge nee: Apply in the 3-leaf stage but before jointing

BURNDOWN USE RATE DPX-SBN49 herbicide (oz/A) RESTRICTIONS Use Area 0.015 0.015 0.0313 0.6 2 0.6 14 0.0038 0.0038 0.0281 SPRAY ADJUVANTS -ALL CROPS OR USES 8 Tribenuron -methyl Thifensuifu ron-m ethyl Maximum Oz/A of Product per Single Application 45 (for grain) Application Timing Refer to the Crop Rotation Section Maximum Number of Applications per Year Maximum Lb Al/A of Product per Year Apply 0.3 to 0.6 oz DPX-SBN49 herbicide per acre as a bumdown treatment prior to planting any crop (except cotton), or shortly after planting wheat (including durum), barley or triticale (prior to emergence). Use the 0.6 ounce per acre rate when weed infestation is heavy or predominantly consists of those weeds listed under the "Weeds Partially Controlled" section of this label, or when application timing and environmental conditions are marginal. See "CROP ROTATION" for the minimum interval allowed between the bumdown application and when a crop may be planted. Sequential treatments of DPX-SBN49 herbicide may also be made provided the total amount of DPX-SBN49 herbicide applied during one post harvest/fallow/pre-plant time period does not exceed 0.6 ounce per acre. Allow at least 14 days between treatments. DPX-SBN49 herbicide needs to be applied in combination with other suitable registered bumdown herbicides (See the "TANK MIXTURES" section of this label for additional information). It is the pesticide user’s responsibility to ensure that all products are registered for the intended use. Read and follow the applicable restrictions and limitations and directions for use on all product labels involved in tank mixing. Users must follow the most restrictive directions for use and precautionary statements of each product in the tank mixture. If the instructions on the tank mix partner label conflicts with this DPX-SBN49 herbicide label, DO NOT use in a tank mixture with DPX-SBN49 herbicide._____ Tribenuron-methyl (Lb ai/A) 0.0075 -0.015______ 0.015 Thifensulfuron-methyl (Lb ai/A 0.0019-0.0038 0.0038 Include a spray adjuvant with applications of DPX-SBN49 herbicide. In addition, an ammonium nitrogen fertilizer may be used. Consult your Ag dealer or applicator, local FMC fact sheets and technical bulletins prior to using an adjuvant system. If another herbicide is tank mixed with DPX-SBN49 herbicide, select adjuvants authorized for use with bothproducts. Products must contain only EPA-exempt ingredients. NONIONIC SURFACTANT (NIS) • Apply 0.06 to 0.5% volume/volume (0.5 pt to 4 pt per 100 gal of spray solution). • Surfactant products must contain at least 60%nonionic surfactant with ahydrophilic/lipophilic balance (HLB) greater than 12. CROP OIL CONCENTRATE (coc) - PETROEUM OR MODIFIED SEED OIL (MSO) • Apply at l%v/v(l gal per 100 gal spray solution) or 2% under arid conditions. MSO adjuvants may be used at 0.5% v/v if specified on local FMC product literature or service policies. • Oil adjuvants must contain at least 80% high quality, petroleum (mineral) or modified vegetable seed oil with at Burndown prior to planting (all crops) Post­ Harvest Burn Maximu m Oz/A of Product per Year For All Applications Maximum Lb AI/A per Year Minimum Treatment Interval (Days) Pre­ Harvest Interval, Days Maximum Lb AI/A per Single Application Active Ingredient (Al) 0,3-0.6 0.6

least 15% surfactant emulsifiers.

---

Nightflowering catchfly Pineappleweed |M:** ; pigweed (@ 0.6 oz) ;/Jim Hill mustard** .try buttercup idon Rocket 9 Narrowleaf hawksbeard Pennsylvania smartweed Prostrate knotweed Red maids Redstem filaree Wild buckwheat Wild carrot Wild garlic Wild radish** Marestailt Marshelderf Mayweed chamomile/Stmkmg chamomile/dog fennel (Anthemis cotula Z,.)fMiners lettuce Nano wleaf hawksbeard * Poison hemlock Prickly lettuce*! Puncturevine Purslane speedwell (@ 0.6 oz) Redroot pigweedt Russian thistle**'' Shepherd’ s-purse Slimleaf lambsquarters Small-flower buttercup (@ 0.6 oz) Smallseed falseflaxf Smartweeds, annual Tansy mustard Tarweed fiddleneck Tumble Tumble/ Velvetleaf White cockle (@ 0.6 oz) Wild mustardf Wild parsnip*** SPECIAL ADJUVANT TYPES • Combination adjuvant products maybe used at doses that provide the required amount ofNIS, COC, MSO and/or ammonium nitrogen fertilizer. Consultproduct literature foruse ratesandrestrictions. • In addition to the adjuvants specified above, other adjuvant types maybe used if they provide the same functionality andhave been evaluated and approved by FMC product management. Consult separate FMC technical bulletins for detailed informationbefore using adjuvanttypesnotspecified on this label. AMMONIUM NITROGEN FERTILIZER • Use 2 qt/acre of a high-quality urea ammonium nitrate (UAN), including 28%N or 32%N, or 2 Ib/acre of a spray-grade ammonium sulfate (AMS). Use 4 qt/acre UAN or 4 lb/acre AMS under arid conditions. • See TANK MIXTURES withLiquidNitrogen Fertilizer for instructions onusing fertilizer as a earner in place of water. WEED CONTROL INFORMATION WEEDS CONTROLLED DPX-SBN49 herbicide effectively controls the following weeds when used according to label directions:_____ Black mustard Blue/Purple mustard Bushy wallflower /Treacle mustardf Canada thistle** Canola, volunteer (except Clearfield) Coast fiddleneck Common Chickweedf Common Groundsel Common Lambsquartersf Common Purslane Com, Gromwell** Com spurry Cowcockle Cressleaf groundsel (butterweed) Curly Dock** Dandelion Deadnettle (@ 0.6 oz) Early whitlowgrass False chamomile/ Wild chamomile/Scentless chamomile (Matricaria maritima L.) Field permycress Flixweedf Hairy buttercup London Rocket WEED PARTIALLY CONTROLLED* DPX-SBN49 herbicide partially controls the following weeds when used according to label directions: Annual sowthistle Common cockleburt Common sunflower (volunteer)+ Common vetch Eastern black nightshade+ Hairy nightshade Hairy vetch** Henbit Jimsonweed_____________

• Partially controlled weeds exhibit a visual reduction in numbers as well as a significant loss of vigor. For better results, include a tankmix partner including 2,4-D, MCPA, bromoxynil or dicamba. See the "TANK MIXTURES" section of this label. ** See the Specific Weed Instructions section of this label for more information.

0.4-0.6 10 Thifensulfuron-methyl (Lb ai/A 0.0038 Thifensulfuron-methyl (Lb ai/A 0.0038 Thifensulfuron-methyl (Lb ai/A 0.0038 Thifensulfuron-methyl (Lb ai/A _______ 0.0025 - 0.0038________ Narrowleaf hawksbeard: During the post4iarvest, fallow, and/or pre-plant bumdown period, DPX-SBN49 herbicide may be used in a tank mix with label rates of a herbicide containing the active ingredient glyphosate for postemergencecontrol ofnanowleafhawksbeard. For wheat, DPX-SBN49 herbicide may be used in a tank mix with 2,4-D for postemergence control of narrowleaf hawksbeard. Add 2,4-D at label rates. Apply this tank mix only in the spring when the wheat is fully tillered and before the jointing stage. Russian thistle, Prickly lettuce; For best results, use DPX-SBN49 in a tank mix with dicamba (including Banvel® herbicide/ Clarity® herbicide) and 2,4-D or MCPA (ester or amine), or bromoxynil containing products (including Bison® herbicide or Bronate® Advanced'^” herbicide). DPX-SBN49 herbicide needs to be applied in the spring when Russian thistle, and prickly lettuce are less than 2" tall or 2" across and are actively growing (refer to the Tank Mixtures section of this label for additional details on rates and restrictions). Tribenuron-methyl (Lb ai/A) 0.01-0.015 Tribenuron-methyl (Lb ai/A) 0.015 Canola, volunteer: In-crop applications of DPX-SBN49 herbicide will not control Clearfield varieties of volunteer canola. Bumdown applications made prior to crop emergence will provide effective control when tank mixed with glyphosate. Corn Cromwell: For best results, apply 0.6 oz of DPX-SBN49 herbicide per acre in combination with 2,4-D or MCPA (refer to the Tank Mixtures sectionofthis label)._____________ Tribenuron-methyl (Lb ai/A) 0.015 Curly Dock: For best results, apply DPX-SBN49 herbicide in combination with 2,4-D or MCPA (refer to the Tank Mixtures sectionofthis label). Kochia; For best results, apply DPX-SBN49 herbicide in combination with other herbicides listed in the Tank Mixtures section ofthis label that control kochia when it is <4 inches in height. Mayweed chamomile / Stinking Chamomile ! dog fennel; For best results, apply 0.4 to 0.6 oz of DPX-SBN49 herbicide per acre___________ DPX-SBN49 herbicide (oz/A) Tumble/Jim Hill mustard: For best results, apply 0.6 oz of DPX-SBN49 herbicide per acre in combination with 2,4-D or MCPA (refer to the Tank Mixtures section of this label for additional details on rates and restrictions). Tribenuron-methyl (Lb ai/A) 0.015 Vetch (common and hairy): For best results, apply DPX-SBN49 herbicide when vetch is less than 6" in length. For severe infestations of vetch, or when vetch is greater than 6" in length, apply DPX-SBN49 herbicide in combination with 2,4-D or MCPA (refer to the Tank Mixtures section ofthis label for additional details onrates and restrictions). Wild radish: For best results, use DPX-SBN49 herbicide plus MCPA plus 0.25% v/v nonionic surfactant (1 qt per 100 gal of spray .solution) to wild radish rosettes less than 6” diameter. Make the application either in the fall or spring. Applications made later than 30 days after weed emergence will result in partial control. Fall applications need to be made before plants harden-off. SU/IMI (Sulfonylurea/Imidazolinone) Resistant Volunteer Sunflowers: For best results, use DPX-SBN49 herbicide in a tank mix with a product containing fluroxypyr (includmgStarane® Ultra herbicide, Starane Ultra DPX-SBN49 herbicide (oz/A) 0.6 DPX-SBN49 herbicide (oz/A) 0.6 ***2,4-D LVE addition required.

• Naturally occurring resistant biotypes are known to occur. SPECIFIC WEED INSTRUCTIONS It is the pesticide user’s responsibility to ensure that all products are registered for the intended use. Read and follow the applicable restrictions and limitations and directions for use on all product labels involved in tank mixing. Users must follow the most restrictive directions for use and precautionary statements of each product in the tank mixture. If the instructions on the tank mix partner label conflicts with this DPX-SBN49 herbicide label, DO NOT use in a tank mixture with DPX-SBN49 herbicide. Canada thistle: For best results, apply 0.6 oz per acre when all thistles are 4" to 8" with 2" to 6" of new growth. Make the application in the spring. DPX-SBN49 herbicide (oz/A) 0.6

11 herbicide + Salvo® herbicide, Starane Ultra herbicide + Sword”), dicamba (including Bauvel herbicide/ Clarity herbicide), 2,4-D or MCPA (ester or amine), glyphosate orbromoxynil containing products (including Bison herbicide or Bronate Advanced herbicide). TANK MIXTURES DPX-SBN49 herbicide may be tank mixed with full or reduced rates of other insecticide, fungicide or herbicides, 2,4-D (ester or amine), MCPA (esteror amine), dicamba (including Banvel herbicide/Clarity herbicide), fluroxypyr containing products (including Starane Ultra herbicide), bromoxynil containing products (including Bison herbicide or Bronate Advanced herbicide), carfentrazone (including Aim® EC herbicide), glyphosate, and postemergence grass herbicides including Goldsky® herbicide, Everest brand products (reference the “Registered Products Reference in this Label” table for suggested Everest brand products), or Rimfire Max® Max herbicide. It is the pesticide user’s responsibility to ensure that all products are registered for the intended use. Read and follow the applicable restrictions and limitations and directions for use on all product labels involved in tank mixing. Users must follow the most restrictive directions for use and precautionary statements of each product in the tank mixture. If the instructions on the tank mix partner label conflicts with this DPX-SBN49 herbicide label, DO NOT use in a tank mixture with DPX-SBN49 herbicide. With 2,4-D (amine or ester) or MCPA (amine or ester) DPX-SBN49 herbicide may be tank mixed with 2,4-D and MCPA (preferably ester formulations) herbicides for use on wheat, barley, oats and triticale. For best results, add 2,4-D or MCPA herbicides at labeled rates. In tank mixes containing a lower rate of the active ingredient 2,4-D or MCPA per acre, add 1 to 2 pt of nonionic surfactant; in tank mixes containing higher rates of the active ingredient 2,4-D or MCPA per acre, add 1 pt of nonionic surfactant. Higher rates of 2,4-D or MCPA may be used, but DO NOT exceed the highest rate allowed by those respective labels. When using higher rates, use of additional nonionic surfactant may not be needed, unless specified otherwise in the 2,4-D or MCPA label, or local guidance. With 2,4-D or MCPA (amine or ester) and Dicamba DPX-SBN49 herbicide maybe applied in a 3-way tank mix with formulations of dicamba (including Banvel herbicide/Clarity herbicide) and 2,4-D or MCPA. Make applications of DPX-SBN49 herbicide + label rates of a product containing the active ingredient dicamba (including Banvel herbicide/Clarity herbicide) + label rate of a product containing the active ingredient of 2,4-D or MCPA (ester or amine) per acre. Use higher rates when weed infestation is heavy. Add 1 to 2 pt of nonionic surfactant to the 3-way mixture, where necessary, as deemed by local guidance. Use of additional nonionic surfactant may not be needed with the higher phenoxy rates and ester phenoxy formulations. Consult the specific 2,4-D or MCPA and dicamba labels, or local guidance for more information. Apply this 3-way combination to winter wheat after the crop is tillering and prior to jointing (first node). In Spring Wheat (including Durum), apply after the crop is tillering and before it exceeds the 5-leaf stage. DO NOT apply this 3-way mixture at high rates more than once a year, or more than twice per year at the low rates. With Bromoxynil containing products DPX-SBN49 herbicide may be tank mixed with bromoxynil containing herbicides registered for use on wheat, barley ortriticale at labeled rates (including Bison herbicide at labeled rates). Tank mixes of DPX-SBN49 herbicide plus bromoxynil may result in reduced control of Canada thistle. With fluroxypyr DPX-SBN49 herbicide may be tank mixed with fluroxypyr containing herbicides for improved control of Kochia (2-4" tall) and other broadleaf weeds. For best results, add fliuoxypry containing herbicides to the tank at 1 to2 oz active ingredient per acre (including Starane). 2,4-D and MCPA herbicides (preferably ester formulations) may be tank mixed with DPX- SBN49 herbicide plus Starane Ultra herbicide. With glyphosate DPX-SBN49 herbicide may be tank mixed with glyphosate herbicides for bumdown of up to 3 inch weeds when applied postemergence as a preplant or harvest bunidown or to fallow fields. Include a spray adjuvant with applications. In addition, an ammonium nitrogen fertilizer may be used. For best results, add a crop oil concentrate or modified seed oil (methylated, ethylated, or saponified) at l%v/v/ (1 gallon per 100 gallons of spray) OR, add nonionic surfactant at 0.25 -0.5% v/v(l-2 quarts per 100 gallons of spray).

12 APPLICATION INFORMATION PRODUCT MEASUREMENT DPX-SBN49 herbicide maybe measured using the DPX-SBN49 herbicide volumetric measuring cylinder provided by FMC. The degree of accuracy of this cylinder varies by ± 7.5%. For more precise measurement, use scales calibrated in ounces. MIXING INSTRUCTIONS

1. Fill the tank 1/4 to 1/3 full of water.
2. While agitating, add the required amount of DPX-SBN49 herbicide.
3. Continue agitation until the DPX-SBN49 herbicide is fully dispersed, at least 5 minutes.
4. Once the DPX-SBN49 herbicide is fully dispersed, maintain agitation and continue filling tank with water. With Postemergence Grass Herbicide When used in tank mixture with GoldSky herbicide, Everest brand products (reference the “Registered Products Reference in this Label” table for suggested Everest brand products), or Rimfire Max herbicide, DPX-SBN49 herbicide will result in improved control of yellow and green foxtail. Consult tank mix partner labeling for any adj vuant, rate, and grass weed height limitations, as reduced grass control mayresult whenusingtankmixtureswith some WSSA Group 1 (ACCase) herbicides. With Insecticide DPX-SBN49 herbicide may be tank mixed or used sequentially with insecticides registered for use on cereal crops. However, under certain conditions (drought stress, or if the crop is in the 2-4 leaf stage), tank mixes or sequential applications of DPX-SBN49 herbicide with organophosphate insecticides (including Lorsban brands, reference the “Registered Products Reference in this Label” table for suggested Lorsban brand products) may produce temporary crop yellowing or, in severe cases, crop injury. The potential for crop injury is greatest when wide fluctuations in day/night temperatures occur just prior to or soon after application. Test these mixtures in a small area before treating large areas. DO NOT apply DPX-SBN49 herbicide within 60 days of crop emergence where an organophosphate insecticide has been applied as an in- furrow treatment because crop injury may result. DO NOT use DPX-SBN49 herbicide plus Malathion because crop injury may result. GRAZING Allow at least 7 days between application and grazing of treated forage. In addition, allow at least 7 days between application and feeding of forage (green chop) from treated areas to livestock. Allow at least 30 days between application and feeding of hay from treated areas to livestock. Allow at least 45 days between application and harvesting of grain. Harvested straw may be used for bedding and/or feed. CROP ROTATION Labeled crops may be planted at specified time intervals following application of labeled rates of DPX-SBN49 herbicide. Use the time intervals listed below to determine the required time interval before planting. Time Interval Before Planting* (days after treatment with DPX-SBN49 herbicide) Days 0 y** 14** 60 45 Refer to individual product labels to determine rotational crop restrictions when tank mixtures are used. **Where DPX-SBN49 herbicide is used on light textured soils (including sands and loamy sands) or on high pH soils (>7.9), extend time to planting by 7 additional days. Crop _________________________________________ Barley, Rice, Triticale and Wheat (including durum) Oats and Soybeans (at DPX-SBN49 rate of 0.3 oz/a) Soybeans Cotton, Field Corn, and Grain/forage Sorghum Sugarbeets, Winter Rape, and Canola Any other crop

13 DPX-SBN49 herbicide needs to be thoroughly mixed with water beforeadding any othermaterial. 5. As the tank is filling, add tank mix partners (if desired) then add the required volume of spray adjuvant. Always add spray adjuvant last. Antifoaming agents may be used. DO NOT use with spray additives that alter the pH of the spray solution below pH 6.0 as rapid product degradation can occur. Spray solutions of pH 7.0 and higher allow for optimum stability of DPX- SBN49 herbicide. 6. If the mixture is not continuously agitated, settling will occur. If settling occurs, thoroughly re-agitate before using. 7. Apply DPX-SBN49 herbicide spray mixture within 24 hours of mixing to avoid product degradation. 8. If DPX-SBN49 herbicide and a tank mix partner are to be applied in multiple loads, pre-slurry the DPX-SBN49 herbicide in clean water prior to adding to the tank. This will prevent the tank mix partner from interfering with the dissolution of the DPX-SBN49 herbicide. APPLICATION METHOD GROUND APPLICATION For optimum spray distribution and thorough coverage, use flat-fan or low-volume flood nozzles. • For flat-fan nozzles, use a spray volume ofatleastS gal per acre (GPA). • For flood nozzles on 30" spacing, use flood nozzles no larger than TK 10 (orthe equivalent), a pressure of at least 30 psi and a spray volume of at least 10 GPA only. For 40" nozzle spacing, use at least 13 GPA; for 60" spacing use at least 20 GPA. It is essential to overlap the nozzles 100% for all spacings. • "Raindrop RA" nozzles are not advised £rDPX-SBN49 herbicide applications, as weed control performance maybe reduced. • Use screens that are 50-mesh or larger. AERIAL APPLICATION Do not apply DPX-SBN49 herbicide by air in the state of New York. See the Spray Drift Management section of this label. APPLICATIONS WITH LIQUID NITOGEN SOLUTION FERTILEZER Liquid nitrogen fertilizer solutions may be used as a carrier in place of water. Run a tank mix compatibility test before mixing DPX-SBN49 herbicide in fertilizer solution. DPX-SBN49 herbicide must first be slurried with water and then added to liquidnitrogen solutions (e.g,, 28-0-0,32-0-0). Ensure that the agitator is running while the DPX-SBN49 herbicide is added. Use of this mixture may result in temporary crop yellowing and stunting. If using low rates of liquid nitrogen fertilizer in the spray solution (less than 50% of the spray solution volume), the addition of surfactant is necessary. Add surfactant at 0.5 pt -1 qtper 100 gal ofspray solution (0.06 -0.25% v/v) based on local guidance. When using high rates of liquid nitrogen fertilizer solution in the spray solution, adding surfactant increases the risk of crop injury. If 2,4-D or MCPA is included withDPX-SBN49 herbicide and fertilizer mixture, ester formulations tend to be more compatible (see manufacturer ’ s label). Additional surfactant may not be needed when using DPX-SBN49 herbicide in tank mix with 2,4-D ester or MCPA ester and liquid nitrogen fertilizer solutions. Consult your agricultural dealer, consultant, field advisor, or FMC representative for guidance before adding an adjuvant to these tank mixtures. Note: In certain areas east of the Mississippi river unacceptable crop response may occur with use of straight or dilute nitrogen fertilizer carrier solutions where cold temperatures or widely fluctuating day/night temperatures exist. In these areas consult your agricultural dealer, consultant, field advisor, or FMC representative for guidance before using nitrogen fertilizer carrier solutions. DO NOT use low rates of liquid nitrogen fertilizer solution as a substitute for surfactant. Liquid nitrogen fertilizer solutions that contain sulfur can increase crop response. DO NOT use with liquid fertilizer solutions with a pH less than 3.0. SPRA Y EQUIPMENT For specific application equipment, refer to the manufacturer’s instructions for additional information on GPA, pressure, speed, nozzle types and arrangements, nozzle heights above the target canopy, etc. Be sure to calibrate air or ground equipment properly before application. Select a spray volume and delivery system that will ensure thorough coverage and a uniform spray pattern with minimum drift. Use higher spray volumes to obtain better coverage when crop canopy is dense. Avoid swath overlapping, and shut off spray booms while starting.

14 turning, slowing, or stopping, to avoid injury to the crop. DO NOT make applications using equipment and. br spray volumes or during weather conditions that might cause spray to drift onto nontarget sites. For additional information on spray drift refer to Spray Drift Management section of label. Continuous agitation is not required to keep DPX-SBN49 herbicide in suspension but may be required to keep tank mix partners in solution or suspension. Refer to tank mix partner labels for additional information. BEFORE SPRAYING DPX-SBN49 herbicide The spray equipment must be clean before DPX-SBN49 herbicide is sprayed. Follow the cleanup procedures specified on the labels of the previously applied products. If no directions are provided, follow the six steps outlined in the After Spraying DPX-SBN49 herbicide section of this label. AT THE END OF THE DAY When multiple loads of DPX-SBN49 herbicide are applied, it is advised that at the end of each day of spraying the interior of the tank be rinsed with fresh water and then partially filled, and the boom and hoses flushed. This will prevent the buildup of dried pesticide deposits which can accumulate in the application equipment. AFTER SPRAYING DPX-SBN49 HERBICIDE AND BEFORE SPRAYING CROPS OTHER THAN WHEAT, BARLEY, OATS, AND TRITICALE To avoid subsequent injury to desirable crops, thoroughly clean all mixing and spray equipment immediately following applications ofDPX-SBN49 herbicide as follows:

1. Empty the tank and drain the sump completely.
2. Spray the tank walls with clean water using a minimum volume of 10% of the tank volume. Circulate the water through the lines, including all by-pass lines, for at least two minutes. Flush the boom well and empty the sprayer. Completely drain the sump.
3. Repeat step 2.
4. Remove the nozzles and screens and clean separately in abucket containing water. The rinsate solution may be applied back to the crop(s) specified on this label. Do not exceed the maximum-labeled use rate. If cleaners are used, consult the cleaner label for rinsate disposal instructions. If no instructions are given, dispose of the rinsate on site or at an approved waste disposal facility. Notes:
5. Steam-cleaning aerial spray tanks is advised to facilitate the removal of any caked deposits.
6. When DPX-SBN49 herbicide is tank mixed with other pesticides, all cleanout procedures for each product need to be examined and the most rigorous procedure need to be followed.
7. Follow any pre-cleanout guidelines advised on other product labels.

MANDATORY SPRAY DRIFT MANAGEMENT 15 Boom-less Ground Applications: • Applicators are required to use a Medium or coarser droplet size (ASABE S572.1) for all applications. • Do not apply when wind speeds exceed 10 miles per hour at the application site. • Do not apply during temperature inversions. Ground Boom Applications: • Apply with the nozzle height recommended by the manufacturer, but no more than 3 feet above the ground or crop canopy. • For applications prior to the emergence of crops and target weeds, applicators are required to use a Coarse or coarser droplet size (ASABE S572.1). • For all other applications, applicators are required to use a Medium or coarser droplet size (ASABE S572.1). • Do not apply when wind speeds exceed 10 miles per hour at the application site. • Do not apply during temperature inversions. Aerial Applications: • Do not release spray at a height greater than 10 feet above the vegetative canopy, unless a greater application height is necessary for pilot safety. • For applications prior to the emergence of crops and target weeds, applicators are required to use a Coarse or coarser droplet size (ASABE S572.1). • For all other applications, applicators are required to use a Medium or coarser droplet size (ASABES572.1). • The boom length must not exceed 65% of the wingspan for airplanes or 75% of the rotor blade diameter for helicopters. • Applicators must use one-half swath displacement upwind at the downwind edge of the field. • Nozzles must be oriented so the spray is directed toward the back of the aircraft. • Do not apply when wind speeds exceed 10 miles per hour at the application site. • Do not apply during temperature inversions. SPRAY DRIFT MANAGEMENT ADVISORIES THE APPLICATOR IS RESPONSIBLE FOR AVOIDING OFF-SITE SPRAY DRIFT. BE AWARE OF NEARBY NON-TARGET SITES AND ENVIRONMENTAL CONDITIONS. IMPORTANCE OF DROPLET SIZE An effective way to reduce spray drift is to apply large droplets. Use the largest droplets that provide target pest control. While applying larger droplets will reduce spray drift, the potential for drift will be greater if applications are made improperly or under unfavorable environmental conditions. Controlling Droplet Size - Ground Boom • Volume - Increasing the spray volume so that larger droplets are produced will reduce spray drift. Use the highest practical spray volume for the application. If a greater spray volume is needed, consider using a nozzle with a higher flow rate. • Pressure - Use the lowest spray pressure recommended for the nozzle to produce the target spray volume and droplet size. • Spray Nozzle - Use a spray nozzle that is designed for the intended application. Consider using nozzles designed to reduce drift. Controlling Droplet Size - Aircraft • Adjust Nozzles - Follow nozzle manufacturers recommendations for setting up nozzles. Generally, to reduce fine droplets, nozzles should be oriented parallel with the airflow in flight. BOOM HEIGHT - Ground Boom Use the lowest boom height that is compatible with the spray nozzles that will provide uniform coverage. For ground equipment, the boom should remain level with the crop and have minimal bounce. RELEASE HEIGHT - Aircraft Higher release heights increase the potential for spray drift. When applying aerially to crops, do not release spray at a height greater than 10 ft above the crop canopy, unless a greater application height is necessary for pilot safety.

SHIELDED SPRAYERS Product Name 16 62719-220 264-1099 34704-609 62719-577 BOOM-LESS GROUND APPLICATIONS: • Setting nozzles at the lowest effective height will help to reduce the potential for spray drift. Aim® EC herbicide__________________ Banvel® herbicide___________________ Bison® herbicide____________________ Bronate® Advanced'^” herbicide_______ Clarity® herbicide___________________ Everest® 2.0 herbicide________ Everest® 3.0 AG herbicide___________ Everest® 3.0 herbicide________ Goldsky® herbicide__________________ Lorban® Advanced Insecticide________ Lorsban® 15G Granular Insecticide Lorsban® SOW in Water Soluble Packets Insecticide__________________________ Lorsban®-4E Insecticide______________ Rimfire® Max herbicide Salvo® herbicide_______ Starane® Ultra Herbicide Carfentrazone-ethyl dicamba MCPA + Bromoxynil MCPA + Bromoxynil dicamba flucarbazone-sodium flucarbazone-sodium flucarbazone-sodium florasulam, fluroxypyr, pyroxsulam Chlorpyrifos Chlorpyrifos Chlorpyrifos When making applications in hot and dry conditions, use larger droplets to reduce effects of evaporation. TEMPERATURE INVERSIONS DRIFT CONTROL ADDITIVES Using product compatible drift control additives can reduce drift potential. When a drift control additive is used, read and carefully observe cautionary statements and all other information on the additive’s label. If using an additive that increases viscosity, ensure that the nozzles and other application equipment will function properly with a viscous spray solution. Preferred drift control additives have been certified by the Council of Producers & Distributors of Agrotechnology (CPDA). Drift potential generally increases with wind speed. AVOID APPLICATIONS DURING GUSTY WIND CONDITIONS. Applicators need to be familiar with local wind patterns and terrain that could affect spray drift. HANDHELD TECHNOLOGY APPLICATIONS: • Take precautions to minimize spray drift. EPA Registration Number 279-3241 66330-276 9779-347 264-690 7969-137 66330-391 66330-433 66330-429 62719-582 62719-591 62719-34 62719-221 Chlorpyrifos propoxycarbazone-sodium, mesosulfuron- methyl _2,4-D fluroxypyr Drift potential is high during a temperature inversion. Temperature inversions are characterized by increasing temperature with altitude and are common on nights with limited cloud cover and light to no wind. The presence of an inversion can be indicated by ground fog or by the movement of smoke from a ground source or an aircraft smoke generator. Smoke that layers and moves laterally in a concentrated cloud (under low wind conditions) indicates an inversion, while smoke that moves upward and rapidly dissipates indicates good vertical air mixing. Avoid applications during temperature inversions. WIND Shielding the boom or individual nozzles can reduce spray drift. Consider using shielded sprayers. Verify that the shields are not interfering with the uniform deposition of the spray on the target area. TEMPERATURE AND HUMIDITY REGISTERED PRODUCTS REFERENCED IN THIS LABEL

17 Refer to the Net Contents section of this product's labeling for the applicable "Nonrefillable Container" or "Refillable Container" designation. Nonrefillable Plastic and Metal Containers (Capacity Equal to or Less Than 50 Pounds): Nonrefillable container. Do not reuse or refill this container. Triple rinse container (or equivalent) promptly after emptying. Triple rinse as follows; Empty the remaining contents into application equipment or a mix tank. Fill the container 1/4 full with water and recap. Shake for 10 seconds. Pour rinsate into application equipment or a mix tank or store rinsate for later use or disposal. Drain for 10 seconds after the flow begins to drip. Repeat this procedure two more times. Then, for Plastic Containers, offer for recycling if available or puncture and dispose of in a sanitary landfill, or by incineration. Do not bum, unless allowed by state and local ordinances. For Metal Containers, offer for recycling if available or reconditioning if appropriate, or puncture and dispose of in a sanitary landfill, or by other procedures approved by state and local authorities Nonrefillable Plastic and Metal Containers (Capacity Greater Than 50 Pounds): Nonrefillable container. Do not reuse or refill this container. Triple rinse container (or equivalent) promptly after emptying. Triple rinse as follows; Empty the remaining contents into application equipment or a mix tank. Fill the container 1/4 full with water. Replace and tighten closures. Tip container on its side and roll it back and forth, ensurmg at least one complete revolution, for 30 seconds. Stand the container on its end and tip it back and forth several times. Turn the container over onto its other end and tip it back and forth several times. Empty the rinsate into application equipment or a mix tank or store rinsate for later use or disposal. Repeat this procedure two more times. Then, for Plastic Containers, offer for recycling if available or puncture and dispose of in a sanitary landfill, or by incineration. Do not bum, unless allowed by state and local ordinances. For Metal Containers, offer for recycling if available or reconditioning if appropriate, or puncture and dispose of in a sanitary landfill, or by other procedures approved by state and local authorities. Nonrefillable Plastic and Metal Containers, e.g., Intermediate Bulk Containers [IBC] (Size or Shape Too Large to be Tipped, Rolled or Turned Upside Down): Nonrefillable container. Do not reuse or refill this container. Clean container promptly after emptying the contents from this container into application equipment or mix tank and before final disposal using the following pressure rinsing procedure. Insert a lance fitted with a suitable tank cleaning nozzle into the container and ensure that the water spray thoroughly covers the top, bottom and all sides inside the container. The nozzle manufacturer generally provides instructions for the appropriate spray pressure, spray duration and/or spray volume. If the manufacturer’s instructions are not available, pressure rinse the container for at least 60 seconds using a minimum pressure of 30 PSI with a minimum rinse volume of 10% of the container volume. Drain, pour or pump rinsate into application equipment or rinsate collection system. Repeat this pressure rinsing procedure two more times. Then, for Plastic Containers, offer for recycling if available or puncture and dispose of in a sanitary landfill, or by incineration. For Metal Containers, offer for recycling if available or reconditioning if appropriate, or puncture and dispose of in a sanitary landfill, or by other procedures approved by state and local authorities. Nonrefillable Paper or Plastic Bags, Fiber Sacks including Flexible Intermediate Bulk Containers (FIBC) or Fiber Drums With Liners: Nonrefillable container. Do not reuse or refill this container. Completely empty paper or plastic bag, fiber sack or drum liner by shaking and tapping sides and bottom to loosen clinging particles. Empty residue into application or manufacturing equipment. Then offer for recycling if available or dispose of empty paper or plastic bag, fiber sack or fiber drum and liner in a sanitary landfill, or by incineration. Do not bum, unless allowed by state and local ordinances. PESTICIDE STORAGE AND DISPOSAL Pesticide Storage; Store the product in original container only. Do not contaminate water, other pesticides, fertilizer, food, or feed in storage. Store in a cool, dry place. Product Disposal: Do not contaminate water, food, or feed by disposal. Wastes resulting from the use of this product must be disposed of on site or at an approved waste disposal facility. CONTAINER HANDLING:

18 NOTICE TO BUYER: Purchase of this material does not confer any rights under patents of countries outside of the United States. Refillable Fiber Drums With Liners: Refillable container (fiber drum only). Refilling Fiber Drum: Refill this fiber drum with DPX-SBN49 herbicide (with TOTALSOL soluble granules) containing thifensulfuron-methyl and tribenuron methyl only. Do not reuse this fiber drum for any other purpose. Cleaning before refilling is the responsibility of the refiller. Completely empty liner by shaking and tapping sides and bottom to loosen clinging particles. Empty residue into application or manufacturing equipment. Disposing of Fiber Drum and/or Liner; Do not reuse this fiber drum for any other purpose other than refilling (see preceding). Cleaning the container (liner and/or fiber drum) before final disposal is the responsibility of the person disposing of the container. Offer the liner for recycling if available or dispose of liner in a sanitary landfill, or by incineration. Do not bum, unless allowed by state and local ordinances. If drum is contaminated and cannot be reused, dispose of it in the manner required for its liner. To clean the fiber drum before final disposal, completely empty the fiber drum by shaking and tapping sides and bottom to loosen clinging particles. Empty residue into application or manufacturing equipment. Then offer the fiber drum for recycling if available or dispose of in a sanitary landfill, or by incineration. Do not bum, unless allowed by state and local ordinances. All Other Refillable Containers: Refillable container. Refilling Container: Refill this container with DPX-SBN49 herbicide (with TOTALSOL soluble granules) containing thifensulfuron-methyl and tribenuron methyl only. Do not reuse this container for any other purpose. Cleaning before refilling is the responsibility of the refiller. Prior to refilling, inspect carefully for damage such as cracks, punctures, abrasions, worn out threads and closure devices. If damage is found, do not use the container, contact FMC at the number below for instructions. Check for leaks after refilling and before transporting. If leaks are found, do not reuse or transport container, contact FMC at the number below for instructions. Disposing of Container: Do not reuse this container for any other purpose other than refilling (see preceding). Cleaning the container before final disposal is the responsibility of the person disposing of the container. To clean the container before final disposal, use the following pressure rinsing procedure. Insert a lance fitted with a suitable tank cleaning nozzle into the container and ensure that the water spray thoroughly covers the top, bottom and all sides inside the container. The nozzle manufacturer generally provides instructions for the appropriate spray pressure, spray duration and/or spray volume. If the manufacturer’s instructions are not available, pressure rinse the container for at least 60 seconds using a minimum pressure of 30 PSI with a minimum rinse volume of 10% of the container volume. Drain, pour or pump rinsate into application equipment or rinsate collection system. Repeat this pressure rinsing procedure two more times. Then, for Plastic Containers, offer for recycling if available or puncture and dispose of in a sanitary landfill, or by incineration. Do not bum, unless allowed by state and local ordinances. For Metal Containers, offer for recycling if available or reconditioning if appropriate, or puncture and dispose of in a sanitary landfill, or by other procedures approved by state and local authorities. Outer Foil Pouches of Water Soluble Packets (WSP): Nonrefillable container. Do not reuse or refill this container. Offer for recycling if available or, dispose of the empty outer foil pouch in the trash as long as WSP is unbroken. If the outer pouch contacts the formulated product in any way, the pouch must be triple rinsed with clean water. Add the rinsate to the spray tank and dispose of the outer pouch as described previously. Do not transport if this container is damaged or leaking. If the container is damaged, leaking or obsolete, or in the event of a major spill, fire or other emergency, contact CHEMTREC (Transportation and Spills) at 1-800- 424-9300, day or night. FMC, Aim, and TotalSol® are trademarks of FMC Corporation or an affiliate. Everest is a registered trademark of Arysta LifeScience North America, LLC. Banvel and Clarity are registered trademarks of BASF Corporation. Bronate Advanced, and Rimfire are trademarks or registered trademarks of Bayer Corporation. Raindrop RA" is a registered trademark of Delavan Goldsky, Lorsban and Starane are registered trademarks ofCorteva Agriscience Salvo is a registered trademark of Loveland Products, Inc. Bison is a registered trademark of Winfield Solutions, LLC D-4002 071519

CONDITIONS OF SALE AND LIMITATIONS OF WARRANTY AND LIABILITY 19 This Condition of Sale and Limitation of Warranty and Liability may not be amended by any oral or written agreement. The Directions for Use of this product must be followed carefully. It is impossible to eliminate all risks inherently associated with the use of this product. Crop injiuy, ineffectiveness, or other unintended consequences may result because of such factors as manner of use or application, weather or crop conditions beyond the control of FMC or Seller. To the extent consistent with applicable law, all such risks shall be assumed by Buyer and User, and, to the extent consistent with applicable law. Buyer and User agree to hold FMC and Seller harmless for any claims relating to such factors. Notice: Read the entire Directions for Use and Conditions of Sale and Limitation of Warranty and Liability before buying or using this product. If the terms are not acceptable, return the product at once, unopened, and the purchase price will be refunded. FMC Corporation, 2929 Walnut Street Philadelphia, PA 19104 © 2015-2019 FMC Corporation. All rights reserved. To the extent consistent with applicable law, FMC or Seller shall not be liable for any incidental, consequential or special damages resulting from the use or handling of this product. TO THE EXTENT CONSISTENT WITH APPLICABLE LAW, THE EXCLUSIVE REMEDY OF THE USER OR BUYER, AND THE EXCLUSIVE LIABILITY OF FMC AND SELLER FOR ANY AND ALL CLAIMS, LOSSES, INJURIES OR DAMAGES (INCLUDE^IG CLAIMS BASED ON BREACH OF WARRANTY, CONTRACT, NEGLIGENCE, TORT, STRICT LIABILITY OR OTHERWISE) RESULTING FROM THE USE OR HANDLING OF THIS PRODUCT, SHALL BE THE RETURN OF THE PURCHASE PRICE OF THE PRODUCT OR, AT THE ELECTION OF FMC OR SELLER, THE REPLACEMENT OF THE PRODUCT. Seller warrants that this product conforms to the chemical description on the label and is reasonably fit for the purposes stated on the Directions for Use when used in accordance with the directions under normal conditions of use. TO THE EXTENT CONSISTENT WITH APPLICABLE LAW, FMC MAKES NO WARRANTIES OF MERCHANTABILITY OR OF IIINISS FOR A PARTICULAR PURPOSE, NOR ANY OTHER EXPRESS OR IMPLIED WARRANTIES WITH RESPECT TO THE SELECTION, PURCHASE, OR USE OF THIS PRODUCT. Any warranties, express or implied, having been made are inapplicable if this product has been used contrary to label instructions, or under abnormal conditions, or under conditions not reasonably foreseeable to (or beyond the control of) Seller or FMC, and, to the extent permitted by applicable law. Buyer assumes the risk of any such use.