crop-chem-docs/corpus/epa_ppls/279-9637.md

CHLORMET XP HERBICIDE

• EPA Reg No: 279-9637
• Registrant: FMC CORPORATION
• Signal word: Caution
• Active ingredients: Chlorsulfuron (62.5%); Metsulfuron-methyl (12.5%)
• Label accepted: 2019-05-20
• Source PDF: https://www3.epa.gov/pesticides/chem_search/ppls/000279-09637-20190520.pdf

---

UNITED STATES ENVIRONMENTAL PROTECTION AGENCY WASHINGTON, DC 20460

Reg Review Label Acceptable v.20151230 OFFICE OF CHEMICAL SAFETY AND POLLUTION PREVENTION May 20, 2019

Bonnie Bieber Registration Specialist FMC Corporation c/o FMC Stine Research Center 1090 Elkton Road Newark, Delaware 19711

Subject: Registration Review La bel Mitigation for Chlorsulfuron and Metsulfuron Methyl Product Name: Chlo rmet XP Herbicide Application Date: 12/14/2017 EPA Registration Number: 279-9637 Decision Number: 540737

Dear Ms. Bieber:

The Agency, in accordance with the Federal Insecticide, Fungicide and Rodenticide Act (FIFRA), as amended, has completed reviewing all of the information submitted with your application to support the Registration Review of the above referenced product in connection with the 22 Sulfonylurea (SU) Herbicides Interim Decision, and has concluded that your submission is acceptable. The label referred to above, submitted in connection with registration under FIFRA, as amended, is acceptable.

Should you wish to add/retain a reference to the company’s website on your label, then please be aware that the website becomes labeling under the Federal Insecticide Fungicide and Rodenticide Act and is subject to review by the Agency. If the website is false or misleading, the product would be misbranded and unlawful to sell or distribute under FIFRA section 12(a)(1)(E). 40 CFR 156.10(a)(5) list examples of statements EPA may consider false or misleading. In addition, regardless of whether a website is referenced on your product’s label, claims made on the website may not substantially differ from those claims approved through the registration process. Therefore, should the Agency find or if it is brought to our attention that a website contains false or misleading statements or claims substantially differing from the EPA approved registration, the website will be referred to the EPA’s Office of Enforcement and Compliance.

A copy of your label stamped “Accepted” is enclosed. Products shipped after 12 months from the date of this amendment must bear the new revised label. Your release for shipment of the product bearing the amended label constitutes acceptance of these conditions. If these conditions are not complied with, the registration will be subject to cancellation in accordance with FIFRA section 6.

Page 2 of 2 EPA Reg. No. 279-9637 Decision No. 540737

If you have any questions about this letter, please contact Erik Kraft by phone at 703-308-9358, or via email at kraft.erik@epa.gov.

Enclosure

Sincerely,

Erik Kraft, Product Manager 24 Fungicide and Herbicide Branch Registration Division (7505P) Office of Pesticide Programs

1 CHLORMETTM XP

HERBICIDE For Use on Wheat, Barley, Triticale, Fallow and CRP Grasses Dry Flowable Active Ingredient By Weight Chlorsulfuron 2-Chloro-N-[(4-methoxy-6-methyl-1,3,5-triazin-2-yl)aminocarbonyl]benzenesulfonamide 62.5% Metsulfuron Methyl Methyl 2-[[[[(4-methoxy-6-methyl-1,3,5-triazin-2-yl)amino]carbonyl]amino]sulfonyl]benzoate 12.5% Other Ingredients 25.0% TOTAL 100% EPA Reg. No. 279-9637 EPA Est. No. Contains 0.75 active ingredient per pound (0.625 chlorsulfuron and 0.125 metsulfuron active ingredient per pound) Nonrefillable Container Refillable Container Net: OR Net: KEEP OUT OF REACH OF CHILDREN CAUTION Si usted no entiende la etiqueta, busque a alguien para que se la explique a usted en detalle. (If you do not understand this label, find someone to explain it to you in detail.) FIRST AID IF SWALLOWED: Call a poison control center or doctor immediately for treatment advice.Have person sip a glass of water if able to swallow. Do not induce vomiting unless told to do so by a poison control center or doctor. Do not give anything to an unconscious person. Have the product container or label with you when calling a poison control center or doctor, or going for treatment. You may also contact 1-800-331-3148 for emergency medical treatment information. PRECAUTIONARY STATEMENTS HAZARDS TO HUMANS AND DOMESTIC ANIMALS CAUTION! Harmful if swallowed. Wash thoroughly with soap and water after handling and before eating, drinking,chewing gum, or using tobacco or using the toilet. Avoid breathing dust or spray mist. Remove and wash contaminated clothing before reuse. PERSONAL PROTECTIVE EQUIPMENT (PPE) Mixers, loaders, applicators, and other handlers must wear: Long-sleeved shirt and long pants. Chemical Resistant Gloves made of any waterproof material including polyethylene or polyvinyl chloride. Shoes plus socks Discard clothing and other absorbent material that have been dr enched or heavily contaminated with this product. Follow manufacturers instructions for cleaning/maintaining PPE. If no such instructions for washables exist, use detergent and hot water. Keep and wash PPE separately from other laundry. ENGINEERING CONTROL STATEMENTS When handlers use closed systems, enclosed cabs, or aircraft in a manner that meets the requirements listed in the Worker Protection Standard (WPS) for agricultural pesticides (40 CFR 170.240(d)(4-6), the handler PPE requirements may be reduced or modified as specified in the WPS. IMPORTANT: When reduced PPE is worn because a closed system is being used, handlers must be provided all PPE specified above for "applicators and other handlers" and have such PPE immediately available for use in an emergency, including a spill or equipment break-down. CHLORSULFURON AND METSULFURON METHYL GROUP 2 HERBICIDE 05/20/2019 279-9637

2 ENVIRONMENTAL HAZARDS Do not apply directly to water, or to areas where surface water is present, or to intertidal areas below the mean high water mark. Do not contaminate water when disposing of equipment washwaters or rinsate. IMPORTANT: When reduced PPE is worn because a closed system is being used, handlers must be provided all PPE specified above for "applicators and other handlers" and have s uch PPE immediately available for use in an emergency, including a spill or equipment break-down. Groundwater Advisory This product is known to leach through soil into groundwater under certain conditions as a result of label use. This product may leach into groundwater if used in areas where soils are permeable, particularly where the water table is shallow. Surface Water Advisory This product may impact surface water quality due to runoff of rain water. This is especially true for poorly draining soils and soils with shallow ground water. This product is classified as having high potential for reaching surface water via runoff for several weeks or more after application. A level, well-maintained vegetative buffer strip between areas to which this product is applied and surface water features including pon ds, streams, and springs will reduce the potential loading of this product from runoff water and sediment. Runoff of this product will be greatly reduced by avoiding applications when rainfall or irrigation is expected to occur within 48 hours. Windblown Soil Particles Advisory This product has the potential to move off-site due to wind ero sion. Soils that are subject to wind erosion usually have a high silt and/or fine to very fine sand fractions and low organic matter content. Other factors which can affect the movement of windblown soil include the intensity and direction of prevailing winds, vegetative cover, site slope, rainfall, and drainage patterns. Avoid applying this product if prevailing local conditions may be expected to result in off-site movement. Non-target Organism Advisory This product is toxic to plants and may adversely impact the fo rage and habitat of non-target organisms, including pollinators, in areas adjacent to the treated area. Protect the forage and habitat of non-target organisms by minimizing spray drift. For further guidance and instructions on how to mi nimize spray drift, refer to the Spray Drift Management section of this label. USER SAFETY RECOMMENDATIONS USERS SHOULD: Wash hands before eating, drinking, chewing gum, using tobacco, or using the toilet. Users shoul d remove clothing/PPE immediately if pesticide gets inside. Then wash thoroughly and put on clean clothing. Users should remove PPE immediately after handling this product. Wash the outside of gloves before removing. As soon as possible wash thoroughly and change into clean clothing.

3 IMPORTANT CHLORMET XP herbicide is registered for use on land primarily dedicated to the long-term production of wheat, barley, triticale, or CRP grasses. PESTICIDE HANDLING • Calibrate sprayers only with clean water away from the well site. • Make scheduled checks of spray equipment. • Ensure that all operation employees accurately measure pesticides. • Mix only enough product for the job at hand. • Avoid over-filling of spray tank. • Do not discharge excess material on the soil at a single spot in the field or mixing/loadingstation. • Dilute and agitate excess solution and apply at labeled rates or uses. • Avoid storage of pesticides near well sites. • When triple rinsing the pesticide container, be sure to add the rinsate to the spray mix. DIRECTIONS FOR USE It is a violation of federal law to use this product in a manner inconsistent with its labeling. Do not apply this product in a way that will contact workers or other persons, either directly or through drift. Only protected handlers may be in the area during application. For a ny requirements specific to your State or Tribe, consult the agency responsible for pesticide regulation CHLORMET™ XP herbicide, referred to below as CHLORMET XP herbic ide, must be used only in accordance with directions on this label. Always read the entire label, including the Limitation of Warranty and Liability. To the extent consistent with applicable law, FMC will not be responsible for losses or damages resulting from the use of this product in any manner not specifically directed by FMC. AGRICULTURAL USE REQUIREMENTS Use this product only in accordance with its labeling and with the Worker Protection Standard, 40 CFR part 170. This Standard contains requirements fortheprotection ofagricultural workers onfarms, forests, nurseries, andgreenhouses, and handlers of agricultural pesticides. It contains requirements for train ing, decontamination, notification, and emergency assistance. It also contains specific instructions and exceptions perta ining to the statements on this label about personal protective equipment (PPE)andrestricted-entry interval. Therequirements inthisboxonlyapplytousesofthisproduct that arecovered bytheWorker ProtectionStandard. Do not enter or allow worker entry into treated areas during th e restricted entry interval (REI) of 4 hours. PPE required for early entry to treated areas that is permitted under the Worker Protection Standard and that involves contact withanything that hasbeentreated, including plants, soil,or water,is: Coveralls. Chemical Resistant Gloves madeofanywaterproof material. Shoesplussocks.

4 PRODUCT INFORMATION CHLORMET XP herbicide is a dry-flowable granule that controls weeds in wheat (including durum), barley, triticale, fallow and CRP grasses. CHLORMET XP herbicide is mixed in water or may be slurried in wa ter then added directly into liquid nitrogen fertilizer solutions and applied as a uniform broadcast spray. A surfactant must be used in the spray mix unless otherwise specified on this label. CHLORMET XP herbicide is noncorrosive, nonflammable, nonvolatile, and does not freeze. CHLORMET XP herbicide controls weeds by both preemergence and postemergence activity. For best preemergence results, apply CHLORMET XP herbicide before weed seeds germinate. Use spr inkler irrigation or allow rainfall to move CHLORMET XP herbicide 2" to 3" deep into the soil profile. For best postemergence results, apply CHLORMET XP herbicide to y oung, actively growing weeds. The use rate depends upon the weed spectrum and size of weeds at the time of applica tion. The degree and duration of control may depend on the following: • weed spectrum and infestation density • weed size at application • environmental conditions at and following treatment ENVIRONMENTAL CONDITIONS AND BIOLOGICAL ACTIVITY CHLORMET XP herbicide is absorbed through the roots and foliage of plants, rapidly inhibiting the growth of susceptible weeds. For preplant and preemergence weed control, rainfall is needed to move CHLORMET XP herbicide into the soil. Weeds will generally not emerge from preplant and preemergence applications. In some cases, susceptible weeds may germinate and emerge a few days after application, but growth t hen ceases and leaves become chlorotic three to five days after emergence. Death of leaf tissue and growing point will fo llow in some species, while others will remain green but stunted and noncompetitive. One to three weeks after postemergence application to weeds, le aves of susceptible plants appear chlorotic, and the growing point subsequently dies. In warm, moist conditions, the express ion of herbicide symptoms is accelerated; in cold, dry conditions, expression of herbicide symptoms is delayed. Death of leaf tissue will follow in some species, while others will remain green but stunted and noncompetitive. Postemergence weed control may be reduced if rainfall occurs within 6 hours after application. CHLORMET XP herbicide provides the best control of weeds in vigo rously growing crops that shade competitive weeds. Weed control in areas of thin crop stand or seeding skips may n ot provide satisfactory control. However, a crop canopy that is too dense at application can intercept spray and reduce weed control. The herbicidal action of CHLORMET XP herbicide may be less effec tive on weeds stressed from adverse environmental conditions (including extreme temperatures or moisture, drought stress), abnormal soi l conditions, or cultural practices that increase weed stress. In these cases, tank mix CHLORMET XP herb icide with other registered herbicides ( including 2,4-D, or MCPA) to aid in control. It is the pesticide user’s responsibility to ensure that all pro ducts are registered for the intended use. Read and follow the applicable restrictions and limitations and directions for use on all product labels involved in tank mixing. Users must follow the most restrictive directions for use and precautionary statements of each product in the tank mixture. If the instructions on the tank mix partner label conflicts with this CHLORMET XP herbicide label, do not use in a tank mixture with CHLORMET XP herbicide.

5 RESTRICTIONS

• Do not apply, drain, or flush equipment on or near desirable trees or other plants, or on areas where their roots may extend, or in locations where the chemical may be washed or moved into contact with their roots.
• Do not use on lawns, walks, driveways, tennis courts, or similar areas.
• Do not apply to wheat, barley, or triticale undersown with legumes and grasses, as injury to the forages will result.
• Do not apply to frozen ground where surface runoff may result.
• Do not apply to snow-covered ground.
• Do not apply to irrigated land where tailwater will be used to irrigate other cropland.
• Do not make more than one application of CHLORMET XP herbicide or any other chlorsulfuron containing product per growing season.
• Do not use in Alamosa, Conejos, Costilla, Rio Grande, and Saguache counties of Colorado.
• Do not discharge excess material on the soil at a single spot in the field, grove, or mixing/loading station.
• Do not store pesticides near well sites.
• Do not apply CHLORMET XP herbicide preemergence on cereals if the seed has germinated and has started to emerge above the soil surface.
• Do not use CHLORMET XP herbicide preemergence on cereals that have been planted into dry soil (“dusted in”) or on very coarse, uneven seedbeds. x Do notuse lessthan0.2oz per acreof CHLORMET XP herbicide preplant, preemergence or postemergence CHLORMET XP herbicide Active Ingredient Equivalent Rate Oz/A Chlorsulfuron Lb. ai/A Metsulfuron-methyl Lb. ai/A 0.2 0.0078 0.0016 For all applications with products containing these active ingredients do not exceed 0.0625 oz ai/A (0.0039 Lb. ai/A) of metsulfuron methyl and 0.37 oz ai/A (0.0231 Lb. ai/A) of chlorsulfuron in a year PRECAUTIONS Injury to or loss of adjacent sensitive crops and vegetation may result from failure to observe thefollowing:
• Take all necessary precautions to avoid all direct or indirect contact (including spray drift) with non-target plants or areas.
• Carefully observe sprayer cleanup instructions, both prior to a nd after using this product, as spray tank residue may damage crops other than wheat or barley. • Wheat, barley, and triticale varieties may differ in their response to various herbicides. FMC advises that you first consult your state experiment station, university, or extension agent as to sensitivity to any herbicide. If no information is available, limit the initial use of CHLORMET XP herbicide to a smallarea. • Wherever CHLORMET XP herbicide is used on land previously treated with Glean® XP herbicide , Ally® XP herbicide , Ally® ExtraSG herbicide (with Totalsol® soluble granules), Ambe r® Custom-Pak™ herbicide or other longer residual herbicides with the same mode of action, read the rotational guidelines onboth labels and follow the one with the longest interval stated for your situation before choosing to rotate to crops other than wheat or barley. • To reduce the potential for movement of treated soil due to wind erosion,do notapply to powdery, dry, or light sandy soils until they have been stabilized by rainfall, trashy mulch, reduced tillage or other cultural practices. Injury to adjacent crops may result when treated soil is blown onto land used to produce cropsother than cerealgrains. • For ground applications applied postemergence to weeds when dry, dusty field conditions exist, control of weeds in wheel track areasmay be reduced.Add 2,4-D or MCPA to improve weed control under these conditions. • Temporary discoloration and/or cropinjury mayoccur if CHLORMET XP herbicide is applied whenthe cropis stressed bysevere weather conditions (including heavy rainfall, prolonged cold weather, or wide fluctuations in day/night temperatures), disease or insect damage, low fertility, applications to coarse soils, or when applied in combination with surfactant and high rates of liquid nitrogenfertilizersolutions.

6 WEED RESISTANCE MANAGEMENT CHLORMET XP herbicide, which contains the active ingredients chlorsulfuron and metsulfuron methyl is a group 2 herbicide based on the mode of action classification system of the Weed Science Society of America. Proactively implementing diversified weed control strategies to minimize selection for weed populations resistant to one or more herbicides is a best practice. A diversified weed manageme nt program may include the use of multiple herbicides with different sites of action and overlapping weed spectrum with or without tillage operations and/or other cultural practices. Research has demonstrated that using the labeled rate and directions for use is important to delay the selection for resistance. The continued effectiveness of this product depends on the succ essful implementation of a weed resistance management program. To aid in the prevention of developing weeds resistant to this product, users must: Scout fields before application to ensure herbicides and rates will be appropriate for the weed species and weed sizes present. Start with a clean field, using either a burndown herbicide application or tillage. Control weeds early when they are relatively small (less than 4 inches). Apply full rates of CHLORMET XP herbicide, for the most difficult to control weed in the field at the specified time (correct weed size) to minimize weed escapes. • Scout fields after application to detect weed escapes or shifts in control of weed species. • Control weed escapes before they reproduce by seed or proliferate vegetatively. • Report any incidence of non-performance of this product agains t a particular weed to your Agsurf representative, local retailer, or county extension agent. • Contact your Agsurf representative, crop advisor, or extension agent to find out if suspected resistant weeds to these MOAs have been found in your region. Do not assume that each listed weed is being controlled by multiple sites of action. Products with multiple active ingredients are intended to broaden the sp ectrum of weeds that are controlled. Some weeds may be controlled by only one of the active ingredient in this product. • If resistance is suspected, treat weed escapes with an herbici de having a site of action other than Group 2 and/or use nonchemical methods to remove escapes, as practical, with the goal of preventing further seed production. • Suspected herbicide-resistant weeds may be identified by these indicators:

• Failure to control a weed species normally controlled by the h erbicide at the dose applied, especially if control is achieved on adjacent weeds;
• A spreading patch of non-controlled plants of a particular wee d species; and
• Surviving plants mixed with controlled individuals of the same species. Additionally, users must follow as many of the following herbicide resistance management practices as is practical: • Use a broad spectrum soil-applied herbicide with other sites of action as a foundation in a weed control program. • Utilize sequential applications of herbicides with alternative sites of action. • Rotate the use of this product with non-Group 2 herbicides. • Avoid making more than two applications of CHLORMET XP herbicid e, and any other Group 2 herbicides within a single growing season unless mixed with an herbicide with a different site of action with an overlapping spectrum for the difficult- to-control weeds. • Incorporate non-chemical weed control practices, including mech anical cultivation, crop rotation, cover crops and weed- free crop seeds, as part of an integrated weed control program. • Use good agronomic principles that enhance crop development an d crop competitiveness. • Thoroughly clean plant residues from equipment before leaving fields suspected to contain resistant weeds. • Manage weeds in and around fields, during and after harvest to reduce weed seed production. INTEGRATED PEST MANAGEMENT This product may be used as part of an Integrated Pest Manageme nt (IPM) program that can include biological, cultural, and genetic practices aimed at preventing economic pest damage. IPM principles and practices include field scouting or other detection methods, correct target pest identification, populati on monitoring, and treating when target pest populations reach locally determined action thresholds. Consult your state cooper ative extension service, professional consultants or other qualified authorities to determine appropriate action treatment threshold levels for treating specific pest/crop systems in yo ur area.

7 CEREALS APPLICATIONS PREPLANT AND PREEMERGENCE CHLORMET XP herbicide can be tank mixed with other products regi stered for preplant/preemergence use in wheat including products with the active ingredient glyphosate. Read and follow all label instructions on timing, precautions, and warnings for any companion products before using these tank mixtures. It is the pesticide user's responsibility to ensure that all products are registered for the intended use. Read and follow the applicable restrictions and limitations and directions for use on all product labels involved in tank mixing. Users must follow the most restrictive directions for use and precautionary statements of each product in the tank mixture. Restrictions: x Do not apply CHLORMET XP herbicide preplant or preemergence on durum or Wampum wheat, barley, or triticale. x Do not apply preemergence or preplant incorporated to late fall planti ngs when cold and/or dry weather can cause delayed seedling emergence and/or stress to seedling plants. Under these conditions, wait until crop has emerged and is showing good vigor before making a postemergence treatment. x Do not apply CHLORMET XP herbicide during the boot stage or early heading stage, as crop injury may result. Precautions: x Crop injury may result when preemergence or preplant incorporat ed applications of CHLORMET XP herbicide are made to wheat seeded less than 1" deep. x Crop injury may result if CHLORMET XP herbicide is used where an organophosphate insecticide has been applied or is intended for use as an in-furrow treatment. APPLICATION INFORMATION CHLORMET XP herbicide Active Ingredient Equivalent Winter Wheat Preplant: Apply CHLORMET XP herbicide at 0.2 to 0.5 oz per acre (before winter wheat is planted). In TX, OK, KS, NE, and SD, preplant application at 0.2 to 0.5 may be shallow incorporated into the top 1 inch of soil. Preemergence: Apply CHLORMET XP herbicide at 0.2 to 0.5 oz per acre (after planting but before winter wheat emerges). I n W Y , M T , N D a n d M N , do not exceed 0.3 oz per acre preemergence. Spring Wheat Preplant/Preemergence: Apply CHLORMET XP herbicide at 0.2 to 0.4 oz per acre in spring wheat (except Durum wheat and Wampum variety of Spring Wheat). In W Y, MT , ND, SD, and MN, do not exceed 0.3 oz per acre preplant or preemergence. Rate (Oz/A) Chlorsulfuron (Lb. ai/A) Metsulfuron-methyl (Lb. ai/A) 0.2 0.0078 0.0016 0.3 0.0117 0.0023 0.4 0.0156 0.0031 0.5 0.0195 0.0039

8 Restrictions: Crop/Use Application Timing Active Ingredient Maximum Oz/A of CHLORMET XP herbicide per Single Application Maximum Lb. ai/A per Single Applicatio n Maximum Oz/A of CHLORMET XP per Year Maximum Lb.ai/A per Year Maximum Number of Applicatio ns per Year Minimum Treatment Interval (Days) Pre-Harvest Interval, Days Winter Wheat Preplant (before winter wheat is planted) Chlorsulfuron 0.5 0.0195 0.5 0.0195 1 Not Applicable 45(for grain)Metsulfuron- methyl 0.0039 0.0039 Winter Wheat (TX, OK, KS, NE, & SD) Preplant (may be shallow incorporated into the top 1 inch of soil) Chlorsulfuron 0.5 0.0195 0.5 0.0195 1 Not Applicable 45(for grain) Metsulfuron- methyl 0.0039 0.0039 Winter Wheat Preemergence (After planting but before winter wheat emerges) Chlorsulfuron 0.5 0.0195 0.5 0.0195 1 Not Applicable 45(for grain) Metsulfuron- methyl 0.0039 0.0039 Winter Wheat (WY, MT, ND, & MN) Preemergence Chlorsulfuron 0.3 0.0117 0.3 0.0117 1 Not Applicable 45(for grain)Metsulfuron- methyl 0.0023 0.0023 Spring Wheat (Except Durum and Wampum varieties) Preplant or Preemergence Chlorsulfuron 0.4 0.0156 0.4 0.0156 1 Not Applicable 45(for grain) Metsulfuron- methyl 0.0031 0.0031 Spring Wheat (WY, MT, ND, SD, & MN) Preplant or Preemergence Chlorsulfuron 0.3 0.0117 0.3 0.0117 1 Not Applicable 45(for grain) POSTEMERGENCE CHLORMET XP herbicide can be tank mixed with other products regi stered for postemergence use in wheat and barley. CHLORMET XP herbicide must not be used within 60 days of crop emergence if an organophosph ate insecticide was used as an in-furrow treatment, or crop injury may result. In areas where late fall or winter cold weather conditions are unpredictable and can be severe (including the Pacific Northwest and Northern plains), to avoid crop injury due to cold weather, do not make applications during the 1 to 4-leaf stage of wheat, barley , or triticale. The combined effects of herbicide stress plus cold weather stress can result in greater crop injury than either stress factor alone. APPLICATION INFORMATION CHLORMET XP herbicide Active Ingredient Equivalent Postemergence: Apply CHLORMET XP herbicide at 0.2 to 0.4 oz per acre to wheat or barley any time after the crop is in the 1-leaf stage, but before boot stage. Apply CHLORMET herbicide at 0.2 to 0.4 oz per acre to triticale any time after the crop is in the 2-3 leaf stage but before the flag leaf is visible. Rate (Oz/A) Chlorsulfuron (Lb. ai/A) Metsulfuron-methyl (Lb. ai/A) 0.2 to 0.4 0.0078 to 0.0156 0.0016 to 0.0031 Restrictions: Crop/Use Application Timing Active Ingredient Maximum Oz/A of CHLORMET XP herbicide per Single Application Maximum Lb. ai/A per Single Application Maximum Oz/A of CHLORMET XP per Year Maximum Lb.ai/A per Year Maximum Number of Applications per Year Minimum Treatment Interval (Days) Pre-Harvest Interval, Days Wheat & Barley Postemergence (After 1-leaf stage but before boot stage) Chlorsulfuron 0.4 0.0156 0.4 0.0156 2 14 45(for grain) Metsulfuron- methyl 0.0031 0.0031 Wheat, Barley, Triticale Postemergence (Pacific Northwest & Northern Plains) After the 4-leaf stage but before boot stage Chlorsulfuron 0.4 0.0156 0.4 0.0156 1 Not Applicable 45(for grain)Metsulfuron- methyl 0.0031 0.0031 Triticale (Areas other than Pacific Northwest & Northern Plains) Postemergence (any time after the crop is in the 2-3 leaf stage but before the flag leaf is visible) Chlorsulfuron 0.4 0.0156 0.4 0.0156 1 Not Applicable 45(for grain)

9 FALLOW APPLICATIONS APPLICATION INFORMATION CHLORMET XP herbicide Active Ingredient Equivalent C H L O R M E T X P h e r b i c i d e m a y b e u s e d a s a f a l l o w treatment and may be tank mixed with other herbicides that are registered for use in fallow. Apply CHLORMET XP herbicide at 0.2 – 0.4 oz per acre in the spring through the fall when the majority of weeds have emerged and are actively growing. Rate (Oz/A) Chlorsulfuron (Lb. ai/A) Metsulfuron-methyl (Lb. ai/A) 0.2 to 0.4 0.0078 to 0.0156 0.0016 to 0.0031 It is the pesticide user’s responsibility to ensure that all pr oducts are registered for the intended use. Read and follow the applicable restrictions and limitations and directions for use on all product labels involved in tank mixing. Users must follow the most restrictive directions for use and precautionary statements of each product in the tank mixture. Restrictions: Crop/Use Application Timing Active Ingredient Maximum Oz/A of CHLORMET XP herbicide per Single Application Maximum Lb. ai/A per Single Applicatio n Maximum Oz/A of CHLORMET XP herbicide per Year Maximum Lb.ai/A per Year Maximum Number of Applications per Year Minimum Treatment Interval (Days) Pre-Harvest Interval, Days Fallow --------- Chlorsulfuron 0.4 0.0156 0.4 0.0156 2 1 ------------Metsulfuron- methyl 0.0031 0.0031 BORDER AREA APPLICATIONS APPLICATION INFORMATION CHLORMET XP herbicide Active Ingredient Equivalent CHLORMET XP herbicide may be used for control of broadleaf weeds in field border areas and fence lines. Apply CHLORMET XP herbicide at 0.2 to 0.5 oz per acre. Rate (Oz/A) Chlorsulfuron (Lb. ai/A) Metsulfuron-methyl (Lb. ai/A) 0.2 to 0.5 0.0078 to 0.0195 0.0016 to 0.0039 Restrictions: Crop/Use Application Timing Active Ingredient Maximum Oz/A of CHLORMET XP herbicide per Single Application Maximum Lb. ai/A per Single Application Maximum Oz/A of CHLORMET XP herbicide per Year Maximum Lb.ai/A per Year Maximum Number of Applications per Year Minimum Treatment Interval (Days) Pre-Harvest Interval, Days Border Area (Field border areas & Fence Lines ) --------- Chlorsulfuron 0.5 0.0195 0.5 0.0195 2 1 ------------ .

10 CRP APPLICATIONS CHLORMET XP herbicide is for control of broadleaf weeds in the following perennial native or improved grasses grown on land enrolled in the Conservation Reserve Program (CRP): Bentgrasses Orchardgrass Blue Grama Sheep fescue Bluestems: big, little, plains, sand, WW spar Sideoats grama Buffalo grass Switchgrass – blackwell Green sprangletop Tall fescue Indiangrass Wheatgrasses: bluebunch, crested, intermediate, pubescent, Siberian, slender, streambank, tall, thickspike, western Kleingrass Wildgrass: beardless, Russian Lovegrasses: atherstone, sane, weeping, wilman, Maximize potential for grass establishment by consulting with t he Natural Resources Conservation Service (NRCS) or other local experts concerning planting techniques and other cultural practices. Because newly planted CRP grass stands do not sufficiently compete with weeds and because weed pressur e in CRP fields is often severe, performance from CHLORMET XP herbicide may not always be satisfactory. An additi onal herbicide application or mowing may be needed. PREPLANT (PRIOR TO PLANTING) APPLICATION INFORMATION CHLORMET XP herbicide Active Ingredient Equivalent CHLORMET XP herbicide may be applied at 0.2 – 0.4 oz per acre to all labelled grasses except bentgrasses, kleingrass, orchardgrass, plains and WW Spar bluestems, Russian wildrye grass, and sheep fescue. The 0.4 oz rate must be used for preemergence applications where residual weed control is important. Rate (Oz/A) Chlorsulfuron (Lb. ai/A) Metsulfuron-methyl (Lb. ai/A) 0.2 to 0.4 0.0078 to 0.0156 0.0016 to 0.0031 If weeds are emerged at time of application, apply CHLORMET XP herbicide with another herbicide having a different mode of action. Read and follow all use instructions, label rates, warnings, and precautions for companion herbicides. EARLY POSTEMERGENCE TO NEW PLANTINGS APPLICATION INFORMATION CHLORMET XP herbicide Active Ingredient Equivalent CHLORMET XP herbicide may be applied at 0.2 – 0.3 oz per acre to all labelled grasses except bentgrasses, orchardgrass, plains and WW Spar bluestems, Russian wildrye grass, and sheep fescue. Because grass species differ in time of emergence, apply only after the majority of grasses are in the 3 to 4 leaf stage. Rate (Oz/A) Chlorsulfuron (Lb. ai/A) Metsulfuron-methyl (Lb. ai/A) 0.2 to 0.3 0.0078 to 0.0117 0.0016 to 0.0023 If weeds are emerged at time of application, apply CHLORMET XP herbicide with another broadleaf herbicide having a different mode of action (see TANK MIXTURES).

11 EARLY POSTEMERGENCE TO ESTABLISHED STANDS APPLICATION INFORMATION CHLORMET XP herbicide Active Ingredient Equivalent CHLORMET XP herbicide may be applied at 0.2 – 0.3 oz per acre to all labelled grasses (except bentgrasses, kleingrass, orchardgras, plains, and WW Spar bluestems, and sheep fescue) when the majority of the grasses have one or more leaves. If stand shows signs of winter stress or a lack of vigor, do not treat as grass injury may result. Rate (Oz/A) Chlorsulfuron (Lb. ai/A) Metsulfuron-methyl (Lb. ai/A) 0.2 to 0.3 0.0078 to 0.0117 0.0016 to 0.0023 If weeds are emerged at time of application, apply CHLORMET XP herbicide with another broadleaf herbicide having a different mode of action (see TANK MIXTURES). LATE POSTEMERGENCE TO ESTABLISHED STANDS APPLICATION INFORMATION CHLORMET XP herbicide Active Ingredient Equivalent CHLORMET XP herbicide may be applied at 0.2 – 0.4 oz per acre to all labelled grasses (make applications to beardless wildrye grass only in the spring after tillering). If stand shows signs of stress or a lack of vigor, do not treat as grass injury may result. Rate (Oz/A) Chlorsulfuron (Lb. ai/A) Metsulfuron-methyl (Lb. ai/A) 0.2 to 0.4 0.0078 to 0.0156 0.0016 to 0.0031 If weeds are emerged at time of application, apply CHLORMET XP herbicide with another broadleaf herbicide having a different mode of action (see TANK MIXTURES). SURFACTANTS - ALL CROPS Unless otherwise specified, add a nonionic surfactant having at least 80%active ingredient at 0.125 to 0.5% v/v (0.5 to 2 qt per 100 gal of spray solution). The higher rate of surfactant is particularly effective with sp ray volumes of 5 gallons per acre (GPA) or less and when using low rates of CHLORMET XP herbicide. Consult your agricult ural dealer, applicator, or FMC representative for a listing of specified surfactants. Antifoaming agents may be used if needed. Do not use low rates of liquid nitrogen fertilizer solution as a substitute for surfactant.

12 WEEDS CONTROLLED CHLORMET XP herbicide effectively controls the following weeds when applied at the rates shown: APPLICATION INFORMATION CHLORMET XP herbicide Active Ingredient Equivalent 0.2 to 0.3 oz per acre Rate (Oz/A) Chlorsulfuron (Lb. ai/A) Metsulfuron-meth yl (Lb. ai/A) 0.2 to 0.3 0.0078 to 0.0117 0.0016 to 0.0023 Blue mustard Mayweed chamomile Broadleaf dock Miners lettuce Bur beakchervil Pineappleweed Bur buttercup (testiculate) Prickly lettuce‡† Carolina geranium Prostrate pigweed Chickweed (common ‡, Plains coreopsis jagged, mouseear) Purslane Conical catchfly Redstem filaree Corn spurry Redroot pigweed ‡ Cow cockle Shepherd’s purse Curly dock Smallseed falseflax ‡ Cutleaf evening primrose Smooth pigweed ‡ False chamomile Tansymustard*† Field pennycress Treacle mustard Flixweed*† ‡ (Bushy wallflower) Groundsel Tumble mustard (Jim Hill) Hempnettle Virginia pepperweed Henbit White cockle Lady's thumb Wild mustard ‡ Lambsquarters‡ Wild carrot APPLICATION INFORMATION CHLORMET XP herbicide Active Ingredient Equivalent 0.3 to 0.4 oz per acre Rate (Oz/A) Chlorsulfuron (Lb. ai/A) Metsulfuron-meth yl (Lb. ai/A) 0.3 to 0.4 0.0117 to 0.0156 0.0023 to 0.0031 Annual bluegrass*† Kochia*†‡ Annual ryegrass*† Pennsylvania smartweed* Annual sowthistle Persian darnel*† Bedstraw*† Prickly poppy (pinnate) Bromus species (cheat, Russian thistle*†‡ downy brome, Speedwell (common, Japanese brome)† ivyleaf) Canada thistle*† Sunflower† ‡ Coast fiddleneck (tarweed) Vetch† Corn gromwell*† Volunteer corn† Dove foot geranium Wild buckwheat† Green foxtail (pigeongrass)‡ Wild radish† Knotweed (prostrate)† Yellow foxtail*† ‡ APPLICATION INFORMATION CHLORMET XP herbicide Active Ingredient Equivalent 0.5 ounces per acre (prior to winter wheat emergence only) Rate (Oz/A) Chlorsulfuron (Lb. ai/A) Metsulfuron-meth yl (Lb. ai/A) 0.5 0.0195 0.0039 Annual ryegrass*†‡ Bromus species (cheat, downy brome, Japanese brome)*†‡ Volunteer corn†

• When used as directed, weeds are suppressed and/or controlled. Weed suppression is a visible reduction in weed competition (reduced population and/or vigor) as compared to an untreated a rea. Degree of suppression will vary with rate used, size of we eds, and environmental conditions followingtreatment. † See the Specific Weed Instructions section for more information regarding controlling and suppressing these weeds. ‡ Naturally occurring resistant biotypes of these weeds are known to occur. See Tank Mixtures, Specific Weed Instructions, and Weed Resistance sections of this label for additional information.

13 SPECIFIC WEED INSTRUCTIONS It is the pesticide user’s responsibility to ensure that all pr oducts are registered for the intended use. Read and follow the applicable restrictions and limitations and directions for use on all product labels involved in tank mixing. Users must follow the most restrictive directions for use and precautionary state ments of each product in the tank mixture. If the instructions on the tank mix partner label conflict with this CHLORMET XP he rbicide label, do not use in a tank mixture with CHLORMET XP herbicide. Annual bluegrass/annual ryegrass CHLORMET XP herbicide Preemergence Apply CHLORMET XP herbicide at 0.5 oz per acre preplant or after planting winter wheat but before wheat emerges. or Apply CHLORMET XP herbicide at 0.5 oz per acre preplant or after planting winter wheat but before wheat emerges followed by a sequential application of metribuzin in the fall once the wheat has reached the 4 to 5-leaf stage of growth and the annual grassy weeds are in the 1 to 3-leaf stage of growth. Refer to the product containing the active ingredient metribuzin label for specific rates and use instructions. or For improved control in the Pacific Northwest, apply a tank mix of CHLORMET XP herbicide at 0.3 to 0.4 oz per acre plus Karmex® DF herbicide at labeled rates preemergence to bluegrass or ryegrass. O n e - h a l f t o 1 ” o f r a i n f a l l i s n e e d e d t o m o v e t h e herbicides into the weed root zone prior to bluegrass or ryegrass emergence. Refer to the product containing the active ingredient diuron label for specific rates and use instructions. CHLORMET XP herbicide Active Ingredient Equivalent Rate (Oz/A) Chlorsulfuron (Lb. ai/A) Metsulfuron-methyl (Lb. ai/A) 0.3 0.0117 0.0023 0.4 0.0156 0.0031 0.5 0.0195 0.0039 CHLORMET XP herbicide Postemergence Apply a tank mix of CHLORMET XP herbicide at 0.2 to 0.4 oz per acre and metribuzin at labeled rates postemergence to the crop and grassy weeds when wheat has reached the 4 to 5-leaf stage of growth and the grassy weeds have reached the 1 to 3-leaf stage of growth. Refer to the product containing the active ingredient metribuzin for rates and specific use instructions. Note : See Bromus species (cheat, downy brome, Japanese brome) section for additional information on the use of metribuzin. CHLORMET XP herbicide Active Ingredient Equivalent Rate (Oz/A) Chlorsulfuron (Lb. ai/A) Metsulfuron-methyl (Lb. ai/A) 0.2 0.0078 0.0016 0.4 0.0156 0.0031 Bedstraw: Apply CHLORMET XP herbicide at 0.4 oz per acre. For postemergence treatments, apply before bedstraw is over 2" long; use 2 qt of surfactant per 100 gal of spray solution. CHLORMET XP herbicide Active Ingredient Equivalent Rate (Oz/A) Chlorsulfuron (Lb. ai/A) Metsulfuron-methyl (Lb. ai/A) 0.4 0.0156 0.0031

14 Bromus species (cheat, downy brome, Japanese brome): Best suppression of these grasses is achieved by applications of CHLORMET XP herbicide with metribuzin (including “Sencor” DF) either in tank mixtures or as sequential treatments. Additional information may be available in a metribuzin supplemental label for winter wheat, barley, and fallow. Allow for adequate rainfall (1/2 to 1") to move CHLORMET XP herbicide and metribuzin into the weed root zone before weeds germinate and develop an established root system. Lack of adequate rainfall following application will result in reduced performance. To avoid the risk of cold weather-related crop injury and lack of performance, apply metribuzin before winter dormancy of the crop and grassy weeds. Excessive rainfall immediately after application may result in crop injury. Do not tank mix CHLORMET XP herbicide plus metribuzin with any other pesticide o ther than surfactants specified on either the CHLORMET XP herbicide or metribuzin labels. Apply only to metrib uzin-approved varieties, see metribuzin label for listing of sensitive wheat and barley varieties. Preemergence/Sequential Applications Apply CHLORMET XP herbicide at 0.5 oz per acre preemergence after planting winter wheat but before wheat emerges. A sequential application of metribuzin may be applied at label rates in the fall once the wheat has reached the 4 to 5-leaf stage of growth and the annual grassy weeds are in the 1 to 3-leaf stage of growth. Refer to the product containing the active ingredient metribuzin for rates and specific use instructions. Idaho, Oregon, and Washington —Apply CHLORMET XP herbicide at 0.4 to 0.5 oz per acre after planting winter wheat but before wheat emerges. CHLORMET XP herbicide Active Ingredient Equivalent Rate (Oz/A) Chlorsulfuron (Lb. ai/A) Metsulfuron-methyl (Lb. ai/A) 0.4 0.0156 0.0031 0.5 0.0195 0.0039 If suppression of bromegrass is not satisfactory following the preemergence application of CHLORMET XP herbicide, apply a sequential treatment of metribuzin at lower rates in the fall when the crop is in the 2-leaf to 3 tiller stage or at higher rates after winter wheat has at least 4 tillers, 2 inches of secondary root systems throughout the field and actively growing. Refer to the product containing the active ingredient metribuzin label for specific rates and use instructions. Postemergence Tank-Mix Applications Apply a tank mix of CHLORMET XP herbicide at 0.2 to 0.4 oz per acre and metribuzin at labeled rates for postemergence applications to the crop and grassy weeds when wheat has reached the 4 to 5-leaf stage of growth and the grassy weeds have reached the 1 to 3-leaf stage of growth. I d a h o , O r e g o n , a n d W a s h i n g t o n–Where broadleaf weeds and bromegrass are the problem, apply a tank mix of CHLORMET XP herbicide at 0.3 to 0.4 oz per acre and metribuzin at lower rates in the fall when wheat or barley is in the 2-leaf to 3-tiller stage or use CHLORMET XP herbicide at 0.3 to 0.4 oz and metribuzin at higher rates when wheat or barley has at least 4 tillers, 2 inches of secondary root systems throughout the field and actively growing. For best results, make application before bromegrass is in the 2 to 3 leaf stage. Consult precautions and directions on the metribuzin labeling before making this application. CHLORMET XP herbicide Active Ingredient Equivalent Rate (Oz/A) Chlorsulfuron (Lb. ai/A) Metsulfuron- methyl (Lb. ai/A) 0.2 0.0078 0.0016 0.3 0.0117 0.0023 0.4 0.0156 0.0031 . Canada thistle: Apply CHLORMET XP herbicide with surfactant after the majority o f thistles have emerged and while they are small (rosette stage to 4" - 6" tall) and actively growing. For maximum long-term effect, yearly treatment may be required.

15 Corn gromwell: Apply CHLORMET XP herbicide at 0.4 oz per acre or tank mix CHLORMET XP herbicide with Bronate Advanced™ and apply postemergence to the crop when weeds are small and actively growing. CHLORMET XP herbicide Active Ingredient Equivalent Rate (Oz/A) Chlorsulfuron (Lb. ai/A) Metsulfuron-methyl (Lb. ai/A) 0.4 0.0156 0.0031 Flixweed, Tansymustard: For best results, tank mix CHLORMET XP herbicide with 2,4-D or MCPA (esters or amines) and apply postemergence when weeds are actively growing. Foxtail/Pigeongrass (green and yellow) (MT, ND, SD and WY): Apply CHLORMET XP herbicide at 0.4 oz per acre in the fall or spring for suppression of these foxtail species. Application before the foxtail germinates is preferred. After emergence, best results are obtained if application is made before the foxtail is more than 1" tall or beyond the 2-leaf stage. 1/2 to 1" of rainfall is needed to move CHLORMET XP herbicide into the weed root zone before the foxtail reaches the 3- leaf stage. CHLORMET XP herbicide Active Ingredient Equivalent Rate (Oz/A) Chlorsulfuron (Lb. ai/A) Metsulfuron-methyl (Lb. ai/A) 0.4 0.0156 0.0031 Kochia, Russian thistle, Prickly lettuce: For best results, CHLORMET XP herbicide may be applied postemerge nce in the spring. Apply when kochia, Russian thistle, and prickly lettuce are less than 2" tall or 2" across and are actively growing. Use CHLORMET XP herbicide in a tank mix with Dicamba (includingBanvel® herbicide/Clarity® herbicide”) and/or 2,4- D and 2 qt surfactant per 100 gal of spray solution. Persian Darnel (MT, ND, SD and WY): Apply CHLORMET XP herbicide at 0.4 oz per acre in the fall or spring for suppression of Persian darnel. Application before the Persian darnel germinates is preferred. After emergence, best results are obtained if application is made before the Persian darnel is beyond the 2-leaf stage. 1/2 to 1" of rainfall is needed to move CHLORMET XP herbicide into the weed root zone before the Persian darnel reaches the 3-leaf stage. CHLORMET XP herbicide Active Ingredient Equivalent Rate (Oz/A) Chlorsulfuron (Lb. ai/A) Metsulfuron-methyl (Lb. ai/A) 0.4 0.0156 0.0031 Prostrate knotweed: For best results, apply CHLORMET XP herbicide preemergence at 0.3 to 0.4 oz per acre to knotweed in the fall. For postemergence treatments, tank mix CHLORMET XP herbicide at 0.3 to 0.4 oz per acre with 2,4-D, MCPA, or dicamba containing products registered for this use (including Banvel herbicide/Clarity herbicide and/or Bronate Advanced and surfactant. Apply to small, actively growing plants (no more than 4 true leaves). For maximum postemergence control, knotweed plants may remain actively growing for 3 to 4 days following application. Refer to the product label for specific rates and use instructions. CHLORMET XP herbicide Active Ingredient Equivalent Rate (Oz/A) Chlorsulfuron (Lb. ai/A) Metsulfuron-methyl (Lb. ai/A) 0.3 0.0117 0.0023 0.4 0.0156 0.0031 Sunflower: For best results, apply CHLORMET XP herbicide after the majority of sunflowers have emerged and are small (not more than 2" tall) and are actively growing. Add surfactant at 2 qt per 100 gal of spray solution. If CHLORMET XP herbicide is applied preemergence, make application in early spring to allow for timely and adequate rainfall to move CHLORMET XP herbicide into the weed root zone before weeds germinate and develop an established root system. Note: In areas of high rainfall, fall applications may not provide adequate residual control of sunflowers. Deep-germinating sunflowers that emerge after a spring treatment may not be controlled.

16 Vetch: For best results, apply CHLORMET XP herbicide postemergence at 0.4 oz per acre plus label rates of 2 , 4 - Do rM C P A( a m i n eo re s t e r )a n ds u r f a c t a n t . CHLORMET XP herbicide Active Ingredient Equivalent Rate (Oz/A) Chlorsulfuron (Lb. ai/A) Metsulfuron-methyl (Lb. ai/A) 0.4 0.0156 0.0031 Volunteer corn: Apply to emerged volunteer corn up to 18" in height. F o r b e s t r e s u l t s , m a k e C H L O R M E T X P h e r b i c i d e application at 0.5 oz per acre preplant or prior to winter wheat emergence. After wheat has emerged, applications are limited to 0.4 oz per acre. CHLORMET XP herbicide Active Ingredient Equivalent Rate (Oz/A) Chlorsulfuron (Lb. ai/A) Metsulfuron-methyl (Lb. ai/A) 0.4 0.0156 0.0031 0.5 0.0195 0.0039 Wild buckwheat: For best results, apply CHLORMET XP herbicide preemergence at 0.4 oz per acre to wild buckwheat in the fall or early spring. For postemergence applications, tank mix CHLORMETherbicide at 0.4 oz per acre with 2,4-D, MCPA, or dicamba products registered for this use (including Banvel herbicide/Clarity herbicide) and/or Bronate Advancedand surfactant. Apply after the majority of seedlings have emerged and are actively growing. Note: In certain situations, 0.3 oz of CHLORMET XP herbicide may provide acceptable control of Wild buckwheat. Consult local FMC directions for additional information. CHLORMET XP herbicide Active Ingredient Equivalent Rate (Oz/A) Chlorsulfuron (Lb. ai/A) Metsulfuron-methyl (Lb. ai/A) 0.3 0.0117 0.0023 0.4 0.0156 0.0031 Wild radish: For best results, apply CHLORMET XP herbicide at 0.3 to 0.4 oz per acre postemergence. CHLORMET XP herbicide Active Ingredient Equivalent Rate (Oz/A) Chlorsulfuron (Lb. ai/A) Metsulfuron-methyl (Lb. ai/A) 0.3 0.0117 0.0023 0.4 0.0156 0.0031

17 TANK MIXTURES CHLORMET XP herbicide may be tank mixed with other registered h erbicides, fungicides, insecticides, or liquid fertilizer. It is the pesticide user’s responsibility to ensure that all products are registered for the intended use. Read an d follow the applicable restrictions and limitations and directio ns for use on all product labels involved in tank mixing. If the instructions on the tank mix partner label conflict with th is CHLORMET XP herbicide label, do not use in a tank mixture with CHLORMET XP herbicide. Since tank-mix partners can interfere with CHLORMET XP herbicid e dispersion in the spray solution, it is advised that CHLORMET XP herbicide be slurried in a separate container before adding it to the tank mix. CHLORMET XP herbicide must be in suspension in the spray tank before adding companion products. With 2,4-D (amine or ester) or MCPA (amine or ester) CHLORMET XP herbicide can be used as a tank-mix treatment with 2,4-D or MCPA herbicides (ester formulations provide best results) after weeds have emerged. For best results, use 0.2 to 0.4 oz of CHLORMET XP herbicide per acre; add 2,4-D or MCPA herbicides to the tank at labeled rates. Surfactant may be added to the mixture at 0.5 to 1 qt per 100 gal of spray solution; however, adding surfactant may increase the potential for crop injury. Do not add a surfactant when CHLORMET XP herbicide plus 2,4-D or MCPA is applied with liquid fertilizer. CHLORMET XP herbicide Active Ingredient Equivalent Rate (Oz/A) Chlorsulfuron (Lb. ai/A) Metsulfuron-methyl (Lb. ai/A) 0.2 0.0078 0.0016 0.4 0.0156 0.0031 Apply CHLORMET XP herbicide plus MCPA after the 3 to 5-leaf stag e but before boot stage. Apply CHLORMET XP herbicide plus 2,4-D after tillering but before boot stage (r efer to the appropriate 2,4-D manufacturer’s label). Applying a tank mixture of CHLORMET XP herbicide, 2,4-D, or MCP A and liquid fertilizer when temperatures are below freezing or when the crop is stressed from cold weather j ust prior to winter dormancy can result in foliar burn and/or crop injury. With Bromoxynil CHLORMET XP herbicide may be tank mixed at labeled rates with b romoxynil containing herbicides registered for use on wheat, barley or triticale. With Dicamba CHLORMET XP herbicide may be tank mixed with products containin g the active ingredient dicamba (including Banvel herbicide) at labeled rates. Use higher rates when weed infestation is heavy. Nonionic surfactant may be added to the mixture at 0.5 to 1 quart per 100 gal of spray solution (0.125 to 0.25% v/v); however, adding nonionic surfactant may increase the potential for crop injury. Tank mixes of CHLOR MET XP herbicide plus dicamba may result in reduced control of some broadleaf weeds.

18 With Diuron In areas where annual bluegrass, annual ryegrass, corn gromwell, green foxtail (pigeongrass) and wild buckwheat are the main weed problems, apply Karmex DF herbicide at labeled rates plus 0.3 to 0.4 o z p e r a c r e C H L O R M E T X P herbicide preemergence. For best results between 1/2" and 1" of rainfall is needed within 1 to 2 weeks after application. Follow all restrictions and use instructions on the diuron labels. For summer fallow (CO, KS, NE, NM, OK, SD, TX, WY), apply Karmex DF herbicide or Direx® 4L herbicide at label rates (both products contain the active ingredient diuron) to wheat stubble or f a l l o w i n a t a n k m i x w i t h C H L O R M E T X P herbicide at 0.2 to 0.3 ounce per acre. Add a Crop Oil Concentrate (COC) at 1 to 2 % v/v or a non- ionic surfactant (NIS) at 0.25 to 0.5 % v/v. Glyphosate products plus AMS may also be added as needed. When using glyphosate products that contain a built-in adjuvant system, add a NIS at 0.25% v/v. Allow at least 90 days after application before planting winter wheat. Refer to the tank mix partners for rates and use instructions. CHLORMET XP herbicide Active Ingredient Equivalent Rate (Oz/A) Chlorsulfuron (Lb. ai/A) Metsulfuron-methyl (Lb. ai/A) 0.2 0.0078 0.0016 0.3 0.0117 0.0023 0.4 0.0156 0.0031 With Fluroxypyr CHLORMET XP herbicide may be tank mixed with fluroxypyr containing herbicides for improved control of Kochia (2- 4" tall) and other broadleaf weed s at labeled rates. 2,4-D and M CP herbicides may be tank mixed with CHLORMET XP herbicide plus fluroxypyr. With Other Broadleaf Control Products For improved control of broadleaf weeds, CHLORMET XP herbicide c an be tank mixed with other herbicides registered on cereals including " WideMatch® herbicide, Aim® EC herbicide, Stinger® Herbicide, or Curtail® Herbicide. With Grass Control Products For improved control of grass weeds, CHLORMET XP herbicide can b e tankmixed with other grass control herbicides registered on cereals including Axial® XL herbicide, Discover® NG herbicide, Everest® 3.0 herbi cide or PowerFlex® herbicide. Antagonism generally does not occur. However, FMC advises that yo u first consult your state experiment station, university, or extension agent, Agricultural dealer, or FMC repr esentative as to the potential for antagonism before using the mixture. If no information is available, limit the initial use of CHLORMET XP herbicide and the grass product to a small area. With Insecticides CHLORMET XP herbicide may be tank mixed with insecticides registered for use on wheat, barley, and fallow. However, under certain conditions (drought or cold stress while crop is in the 2- to 4-leaf stage), tank mixtures or sequential treatments of CHLORMET XP herbicide and organophosphate insectic ides (including methyl or ethyl parathion, or “Di- Syston”) may produce temporary crop yellowing or, in severe cas es, crop injury. The potential for crop injury is greatest when there are wide fluctuations in day/night temperatures just prior to or soon after treatment. Read and follow directions on companion product labels and limit first use to a small area . If no symptoms of crop injury appear, larger acreage can be treated. Restrictions: ¾ Do not apply CHLORMET XP herbicide within 60 days of crop emergence whe re an organophosphate insecticide (including “Di-Syston”) has been applied as an in-furrow treatment, as crop injury may result. ¾ Do not use CHLORMET XP herbicide plus “Malathion”, as crop injury may result. ¾ In the Pacific Northwest, do not use CHLORMET XP herbicide with products containing the active ingredient chlorpyrifos, as crop injury may result.

19 With Fungicides CHLORMET XP herbicide may be tank mixed with other fungicide or other fungicides whenever the proper timing for herbicide and fungicide treatments coincide. With Liquid Nitrogen Fertilizer Solution Liquid nitrogen fertilizer solu tions may be used as a carrier i n place of water. Run a tank mix compatibility test before mixing CHLORMET XP herbicide in fertilizer solution. If 2,4-D or MCPA is included with CHLORMET XP herbicide and fertilizer mixture, ester formulations tend to be more compatible (See manufacturer’s label). If using low rates of liquid nitrogen fertilizer in the spray solution (less than 50% of the spray solution volume), the addition of surfactant is necessary. When using high rates of liquid nit rogen fertilizer in the spray solution, adding surfactant increases the risk of crop injury. Consult local specifications for details on surfactant addition. Restrictions: ¾ DO NOT add surfactant when using CHLORMET XP herbicide in tank mix with 2,4-D ester or MCPA ester and liquid nitrogen fertilizer solutions. ¾ DO NOT use with liquid fertilizer solutions with a pH less than 3.0. ¾ DO NOT use low rates of liquid fertilizer solution as a substitute for surfactant. GRAZING There are no grazing restrictions on CHLORMET XP herbicide. CROP ROTATION Before using CHLORMET XP herbicide, carefully consider your crop rotation plans and options. For rotational flexibility, do not treat all of your wheat, barley, or fallow acres at the same time. MINIMUM ROTATION INTERVALS Minimum rotation intervals* are determined by the rate of breakdown of CHLORMET XP herbicide applied. CHLORMET XP herbicide breakdown in the soil is affected by soil pH, soil temperature, soil microorganisms, and soil moisture. Low soil pH, high soil temperature, and high soil moisture increase CHLORMET XP herbicide breakdown in soil, while high soil pH, low soil temperature, and low soil moisture slow CHLORMET XP herbicide breakdown. Of these three factors, only soil pH remains relatively constant. Soil temperature, and to a greater extent, soil moisture, can vary significantly from year to year and from area to area. For this reason, soil temperatures and soil moisture must be monitored regularly when considering rotating to other crops.

• The minimum rotation interval represents the period of time from the last CHLORMET XP herbicide application to the anticipated date of the next planting. SOIL pH LIMITATIONS CHLORMET XP herbicide may not be used on fields having a soil pH above 7.9, as extended soil residual activity could extend crop rotation intervals beyond those specified in the rotation table, and under certain conditions, could injure wheat or barley. In addition, other crops planted in high-pH soils can be extremely sensitive to low concentrations of CHLORMET XP herbicide. CHLORMET XP herbicide may not be used on soils with a pH below 5. 0, as additional crop stress from low pH and aluminum toxicity may result in crop injury. Checking Soil pH Before using CHLORMET XP herbicide, determine the soil pH of th e field. To obtain a representative pH value, take s e v e r a l s a m p l e s f r o m d i f f e r e n t a r e a s o f t h e f i e l d b e t w e e n 0 " a nd 4" deep and analyze them separately. Consult local extension publications for additional information on advised soil sampling procedures. BIOASSAY A field bioassay must be completed before rotating to any crop not listed (See the Rotation Intervals table), or if the soil pH is not in the specified range, or if the use rate applied is n ot s pe c i f i e d i n t h e t a bl e , or i f t h e m in im um cum u l a ti ve precipitation has not occurred since application. To conduct a field bioassay, grow test strips of the crop or cr ops you plan to grow the following year in fields previously treated with CHLORMET XP herbicide. Crop response to the bioassay will indicate whether or not to rotate to the crop(s) grown in the test strips. If a field bioassay is planned, check with your local state agr icultural extension service for information detailing the field bioassay procedure.

20 CEREAL CROPS—ROTATION INTERVALS Location Soil pH* Application Rate (oz/A) Active Ingredient Application Rate (Lb. ai/A) Minimum Rotation Interval (Months) Wheat/Rye/ Triticale** Oat Barley AL, AR, DE, GA, IA, IL, IN, KS, KY, LA, MD, MO, MS, NC, NE, NJ, NM, OH, OK, PA, SC, TN, TX, VA 7.9 or lower 0.2 to 0.4 Chlorsulfuron 0.0078 to 0.0156 01 0 1 0Metsulfuron- methyl 0.0016 to 0.0031 7.9 or lower 0.5 Chlorsulfuron 0.0195 41 0 1 6Metsulfuron- methyl 0.0039 CO, NE (Panhandle), Southeastern WY 7.9 or lower 0.2 to 0.4 Chlorsulfuron 0.0078 to 0.0156 01 0 1 0Metsulfuron- methyl 0.0016 to 0.0031 ID, OR, WA, MT, ND, SD, and WY (except Southeastern WY) 6.5 or lower 0.2 to 0.4 Chlorsulfuron 0.0078 to 0.0156 01 0 1 0Metsulfuron- methyl 0.0016 to 0.0031 6.6 to 7.9 0.2 to 0.4 Chlorsulfuron 0.0078 to 0.0156 01 0 1 6Metsulfuron- methyl 0.0016 to 0.0031

• See the Maximum Use Rates and Soil pH Limitations sections of this label. ** For Durum wheat and Wampum variety of Spring Wheat, follow the rotation intervals listed under Barley CRP -- RECROPPING INTERVALS Location Crop Soil pH* Application Rate (oz/A) Active Ingredient Application Rate (Lb. ai/A) Rotation Interval (Months) AL, AR, CA, CO, DE, GA, ID, IL, IN, KS, KY, LA, MD, MO, MS, NC, NE, NJ, NM, OH, OK, OR, PA, SC, TN, TX, UT, VA, WA, Southeastern WY all grasses* 7.9 or lower 0.2 to 0.3 Chlorsulfuron 0.0078 to 0.0117 2 Metsulfuron-methyl 0.0016 to 0.0023 0.4 to 0.5 Chlorsulfuron 0.0156 to0.0195 4 Metsulfuron-methyl 0.0031 to 0.0039 MT, ND, SD, Northern WY All grasses* 7.5 or lower 0.2 to 0.4 Chlorsulfuron 0.0078 to 0.0156 4Metsulfuron-methyl 0.0016 to 0.0031 Wheatgrass* only 7.6 to 7.9 0.2 to 0.4 Chlorsulfuron 0.0078 to 0.0156 4Metsulfuron-methyl 0.0016 to 0.0031 *The following grasses may be planted for Conservation Reserve Program (CRP) acres after the intervals specified in the table above: Bentgrasses Blue grama Bluestems - big, little, plains, sand, ww spar Buffalograss Galleta Green needlegrass Indiangrass Indian ricegrass Lovegrasses - sand, weeping Orchardgrass (except Piaute) Prairie sandreed Sand dropseed Sheep fescue Sideoats grama Switchgrass Wheatgrasses - crested intermediate, pubescent, slender, streambank, tall, thickspike, western Wild ryegrasses - beardless, Russian

21 NON CEREAL CROPS—ROTATION INTERVALS—NON IRRIGATED LAND Location Crop Soil pH Application Rate (oz/A) Active Ingredient Application Rate (Lb. ai/A) Cumulative Precipitation (Inches) Rotation Interval (Months)State County or Area Colorado E. of Continental Divide Field corn, Millets 7.4 or lower 7.5 to 7.9 0.2 to 0.4 Chlorsulfuron 0.0078 to 0.0156 20 45 11 36Metsulfuron- methyl 0.0016 to 0.0031 Grain sorghum 7.5 or lower 7.6 to 7.9 0.2 to 0.4 Chlorsulfuron 0.0078 to 0.0156 45 60 36 48Metsulfuron- methyl 0.0016 to 0.0031 sulfonylurea tolerant (STS®) soybeans** 7.5 or lower*** 0.2 to 0.4 Chlorsulfuron 0.0078 to 0.0156 ‡4 †Metsulfuron- methyl 0.0016 to 0.0031 Grain sorghum 7.2 or lower 7.3 - 7.5*** 0.2 to 0.3 Chlorsulfuron 0.0078 to 0.0117 ‡ ‡ 4† 8†Metsulfuron- methyl 0.0016 to 0.0023 Idaho* Northern (Benewah, Bonner, Boundary, Clearwater, Idaho, Koontenai, Latah, Lewis, and Nez Perce counties) Pea (dry) 6.5 or lower 0.2 to 0.4 Chlorsulfuron 0.0078 to 0.0156 35 24Metsulfuron- methyl 0.0016 to 0.0031 Lentils 6.5 or lower 0.2 to 0.4 Chlorsulfuron 0.0078 to 0.0156 50 36Metsulfuron- methyl 0.0016 to 0.0031 Kansas All areas Field Corn, Millets 7.4 or lower 7.5 to 7.9 0.2 to 0.4 Chlorsulfuron 0.0078 to 0.0156 20 45 11 36Metsulfuron- methyl 0.0016 to 0.0031 sulfonylurea tolerant (STS®) soybeans** 7.5 or lower*** 0.2 to 0.4 Chlorsulfuron 0.0078 to 0.0156 ‡ 4† Metsulfuron- methyl 0.0016 to 0.0031 Central (Generally E. of Highway 183, W. of the Flinthills) Grain sorghum Soybeans 7.9 or lower 0.2 to 0.5 Chlorsulfuron 0.0078 to 0.0195 25 14 Metsulfuron- methyl 0.0016 to 0.0039 W. Central and Western (generally W. of Highway 183 to the western edge of Grant, Kearny, Logan, Rawlings, Stevens, Thomas, and Wichita counties) Grain sorghum 7.5 or lower 7.6 to 7.9 0.2 to 0.4 Chlorsulfuron 0.0078 to 0.0156 21 42 14 26 Metsulfuron- methyl 0.0016 to 0.0031 Soybeans 7.5 or lower 7.6 to 7.9 0.2 to 0.4 Chlorsulfuron 0.0078 to 0.0156 40 60 24 36 Metsulfuron- methyl 0.0016 to 0.0031 Far Western (In the last tier of counties along the KS/CO border: Cheyenne, Greeley, Hamilton, Morton, Sherman, Stanton, and Wallace) Grain sorghum Soybeans 7.5 or lower 7.6 to 7.9 0.2 to 0.4 Chlorsulfuron 0.0078 to 0.0156 36 60 26 48 Metsulfuron- methyl 0.0016 to 0.0031 Western (W. of hwy 183) Grain sorghum 7.2 or lower 7.3 - 7.5*** 0.2 to 0.3 Chlorsulfuron 0.0078 to 0.0117 ‡ ‡ 4† 6† Metsulfuron- methyl 0.0016 to 0.0023 Eastern (E. of hwy 183) Grain sorghum 7.5 or lower 0.2 to 0.4 Chlorsulfuron 0.0078 to 0.0156 ‡4 † Metsulfuron- methyl 0.0016 to 0.0031

22 NON CEREAL CROPS—ROTATION INTERVALS—NON IRRIGATED LAND (CONTINUED) Location Crop Soil pH Applicatio n Rate (oz/A) Active Ingredient Application Rate (Lb. ai/A) Cumulative Precipitation (Inches) Rotation Interval (Months)State County or Area Nebraska All areas Field Corn, Millets 7.4 or lower 7.5 to 7.9 0.2 to 0.4 Chlorsulfuron 0.0078 to 0.0156 20 45 11 36Metsulfuron- methyl 0.0016 to 0.0031 sulfonylurea tolerant (STS®) soybeans** 7.5 or lower*** 0.2 to 0.4 Chlorsulfuron 0.0078 to 0.0156 ‡4 †Metsulfuron- methyl 0.0016 to 0.0031 S. Central (Franklin, Nuckolls, Thayer, an d Webster counties) Grain sorghum Soybeans 7.9 or lower 0.2 to 0.5 Chlorsulfuron 0.0078 to 0.0195 25 14Metsulfuron- methyl 0.0016 to 0.0039 Western counties (Chase, Dundy, Frontier, Furnas, Gosper, Harlan, Hayes, Hitchcock, Perkins, Phelps, and Red Willow) Grain sorghum, Soybeans 7.5 or lower 7.6 to 7.9 0.2 to 0.4 Chlorsulfuron 0.0078 to 0.0156 40 60 24 36Metsulfuron- methyl 0.0016 to 0.0031 Panhandle (Deuel, Garden, and Sheridan counties and all counties W. to the WY border) Grain sorghum 7.5 or lower 0.2 to 0.4 Chlorsulfuron 0.0078 to 0.0156 45 24Metsulfuron- methyl 0.0016 to 0.0031 Western (W. of hwy 183) Grain sorghum 7.2 or lower 7.3 - 7.5*** 0.2 to 0.3 Chlorsulfuron 0.0078 to 0.0117 ‡ ‡ 4† 6†Metsulfuron- methyl 0.0016 to 0.0023 Eastern (E. of hwy 183) Grain sorghum 7.5 or lower 0.2 to 0.4 Chlorsulfuron 0.0078 to 0.0156 ‡4 †Metsulfuron- methyl 0.0016 to 0.0031 Oklahoma All areas Field Corn, Millets 7.4 or lower 7.5 to 7.9 0.2 to 0.4 Chlorsulfuron 0.0078 to 0.0156 20 45 11 36Metsulfuron- methyl 0.0016 to 0.0031 sulfonylurea tolerant (STS®) soybeans** 7.5 or lower*** 0.2 to 0.4 Chlorsulfuron 0.0078 to 0.0156 ‡4 †Metsulfuron- methyl 0.0016 to 0.0031 East of Panhandle Grain sorghum, Cotton, Mung beans, Soybeans 7.9 or lower 0.2 to 0.5 Chlorsulfuron 0.0078 to 0.0195 25 14Metsulfuron- methyl 0.0016 to 0.0039 Panhandle Grain sorghum 7.2 or lower 0.2 to 0.3 Chlorsulfuron 0.0078 to 0.0117 ‡ 4† 7.3 - 7.5*** Metsulfuron- methyl 0.0016 to 0.0023 ‡ 6† up to 7.9 up to 0.4 Chlorsulfuron 0.0156 30 25Metsulfuron- methyl 0.0031 All areas except Panhandle Grain sorghum 7.5 or lower 0.2 to 0.4 Chlorsulfuron 0.0078 to 0.0156 ‡4 †Metsulfuron- methyl 0.0016 to 0.0031 Oregon* Northeastern counties (Baker, Umatilla, Union, Wallowa) Pea (dry) 6.5 or lower 0.2 to 0.4 Chlorsulfuron 0.0078 to 0.0156 35 24Metsulfuron- methyl 0.0016 to 0.0031 Lentils 6.5 or lower 0.2 to 0.4 Chlorsulfuron 0.0078 to 0.0156 50 36Metsulfuron- methyl 0.0016 to 0.0031 West of the Cascades Ryegrass (annual and perennial) Crimson Clover 6.5 or lower 0.2 to 0.4 Chlorsulfuron 0.0078 to 0.0156 20 9Metsulfuron- methyl 0.0016 to 0.0031 Red Clover Snap Beans 6.5 or lower 0.2 to 0.4 Chlorsulfuron 0.0078 to 0.0156 40 15Metsulfuron- methyl 0.0016 to 0.0031 Field Corn 6.5 or lower 0.2 to 0.4 Chlorsulfuron 0.0078 to 0.0156 60 22Metsulfuron- methyl 0.0016 to 0.0031

23 NON CEREAL CROPS—ROTATION INTERVALS—NON IRRIGATED LAND (CONTINUED) Location Crop Soil pH Application Rate (oz/A) Active Ingredient Application Rate (Lb. ai/A) Cumulative Precipitation (Inches) Rotation Interval (Months)State County or Area Texas All areas Field Corn, Millets 7.4 or lower 0.2 to 0.4 Chlorsulfuron 0.0078 to 0.0156 20 45 11 367.5 to 7.9 Metsulfuron- methyl 0.0016 to 0.0031 sulfonylurea tolerant (STS®) soybeans** 7.5 or lower*** 0.2 to 0.4 Chlorsulfuron 0.0078 to 0.0156 ‡4 †Metsulfuron- methyl 0.0016 to 0.0031 Eastern counties (see below) Grain sorghum, Cotton, Mung beans, Soybeans 7.9 or lower 0.2 to 0.5 Chlorsulfuron 0.0078 to 0.0195 25 14Metsulfuron- methyl 0.0016 to 0.0039 The Eastern counties are: Archer, Bell, Bosque, Bowie, Camp, C ass, Clay, Colin, Cooke, Coryell, Dallas, Delta, Denton, Ellis, Falls, Fannin, Franklin, Grayson, Hill, Hood, Hopkins, Hunt, Jack, Johnson, Kaufman, Lam ar, Limestone, McLennan, Milam, Montague, Morris, Navarro, Palo Pinto, Parker, Rains, Red River, Robertson, Rockwall, Somervell, Tarrent, Titus, Upsh ur, Van Zandt, Wichita, Williamson, Wise, Wood, Young Central counties (see below) Cotton, Grain sorghum 7.9 or lower 0.2 to 0.4 Chlorsulfuron 0.0078 to 0.0156 25 14Metsulfuron- methyl 0.0016 to 0.0031 7.9 or lower 0.5 Chlorsulfuron 0.0195 46 26 Metsulfuron- methyl 0.0039 The Central counties are: Baylor, Callahan, Eastland, Foard, Hardeman, Haskell, Knox, Shackelford, Stephens, Throckmorton, Wil barger Panhandle Grain sorghum 7.2 or lower 0.2 to 0.3 Chlorsulfuron 0.0078 to 0.0117 ‡ 4† 7.3 - 7.5*** Metsulfuron- methyl 0.0016 to 0.0023 ‡6 † up to 7.9 up to 0.4 Chlorsulfuron 0.0156 30 25Metsulfuron- methyl 0.0031 All areas except Panhandle Grain sorghum 7.5 or lower 0.2 to 0.4 Chlorsulfuron 0.0078 to 0.0156 ‡4 †Metsulfuron- methyl 0.0016 to 0.0031 Washington* Eastern (Asotin, Columbia, Garfield, Pend Oreille, Spokane, Stevens, Walla Walla, Whitman) Pea (dry) 6.5 or lower 0.2 to 0.4 Chlorsulfuron 0.0078 to 0.0156 35 24Metsulfuron- methyl 0.0016 to 0.0031 Lentils 6.5 or lower 0.2 to 0.4 Chlorsulfuron 0.0078 to 0.0156 50 36Metsulfuron- methyl 0.0016 to 0.0031 Wyoming Southeastern counties (Platte, Goshen, and Laramie) Field corn, Millets 7.4 or lower 0.2 to 0.4 Chlorsulfuron 0.0078 to 0.0156 20 45 11 367.5 to 7.9 Metsulfuron- methyl 0.0016 to 0.0031 Grain sorghum 7.5 or lower 0.2 to 0.4 Chlorsulfuron 0.0078 to 0.0156 45 60 36 487.6 to 7.9 Metsulfuron- methyl 0.0016 to 0.0031 Note: Do not plant sorghum grown for hybrid seed production.

• In Idaho, Oregon & Washington for peas and lentils, a field bioassay is required if soil pH is above 6.5 **Under certain conditions (including drought, prolonged cold weather, pH variability in the fields) temporary discoloration and/or crop injury may occur to sulfonylurea tolerant (STS®) soybeans planted after CHLORMET XP herbicide applications. ***W he re a CA TA ST ROPHI C CROP L OSS has oc curre d afte r a CHL ORMET XP herbicide application due to a natural disaster (including freezing weather, hail damage, insect damage, disease damage), grain sorghum can be planted at 4 months where the soil pH is 7.3 to 7.5 or sulfonylurea tolerant (STS®) soybeans where the soil pH is 7.5 to 7.9. These crops wil l have some level of temporary discoloration and/or crop injury if planted at this reduced interval after CHLORMET XP herbicide application. This potential damage and yield loss is accepted by the grower due to the critical need to get a crop planted after this emergency. Growers not willing to accept this level of potential early season crop injury and yield loss must follow the standard rotational guidelines in the table above. In some cases, this injury may be severe and may affect the crop growth, development, and yield. The severity of the injury increases with higher pH levels, higher applied CHLORMET XP herbicide rate, drier soil condition s after CHLORMET XP herbicide application and prior to planting the rotational crop, and the shorter the rotational interval. †These intervals may also be used for irrigated land. These intervals do not apply to crops grown for seed. ‡Rotation intervals are based on normal precipitation/irrigation amounts. If in a water deficit including a drought, extend rotation intervals until cumulative rainfall/irrigation reaches the normal range.

24 NON CEREAL CROPS—ROTATION INTERVALS—IRRIGATED AND NON IRRIGATED LAND State Crop Soil pH Application Rate (oz/A) Active Ingredient Application Rate (Lb. ai/A) Rotation Interval* (months) AL, AR, DE, GA, IL, IN, KY, LA, MD, MS, MO, NC, NJ, OH, PA, SC, TN, VA, WV sulfonylurea tolerant STS® soybeans† 7.9 or lower 0.2 to 0.5 Chlorsulfuron 0.0078 to 0.0195 6 Metsulfuron-methyl 0.0016 to 0.0039 Grain Sorghum, Cotton Non- STS® Soybeans Field Corn Rice 7.9 or lower 0.2 to 0.5 Chlorsulfuron 0.0078 to 0.0195 18 Metsulfuron-methyl 0.0016 to 0.0039 Grain sorghum 7.5 or lower 0.2 to 0.4 Chlorsulfuron 0.0078 to 0.0156 4Metsulfuron-methyl 0.0016 to 0.0031 *Rotation intervals are based on normal precipitation/irrigation amounts. If in a water deficit including a drought, extend rotation intervals until cumulative rainfall/irrigation reaches the normal range. These intervals do not apply to crops grown for seed. †Under certain conditions (including drought, prolonged cold weather, pH variability in fields), temporary discoloration and/or crop injury may occur to sulfonylurea tolerant (STS®) soybeans planted after CHLORMET XP herbicide applications.

25 APPLICATION INFORMATION PRODUCT MEASUREMENT CHLORMET XP herbicide is measured using the CHLORMET XP herbicid e volumetric measuring cylinder. The degree of accuracy of this cylinder varies by ± 7.5%. For more precise measurement, use scales calibrated in ounces. MIXING INSTRUCTIONS

1. Fill the tank 1/4 to 1/3 full of water (If using liquid nitro gen fertilizer solution in place of water, see Tank Mixtures se ctions for additional details).
2. While agitating, add the required amount of CHLORMET XP herbicide.
3. Continue agitation until the CHLORMET XP herbicide is fully dispersed, at least 5 minutes.
4. Once the CHLORMET XP herbicide is fully dispersed, maintain agitation and continue filling tank with water. CHLORMET XP herbicide needs to be thoroughly mixed with water before adding any other material. 5.As the tank is filling, add tank mix partners (if desired) th en add the necessary volume of nonionic surfactant. Always add surfactant last.
5. If the mixture is not continuously agitated, settling will occur. If settling occurs, thoroughly re-agitate before using.
6. Apply CHLORMET XP herbicide spray mixture within 24 hours of mixing to avoid product degradation.
7. If CHLORMET XP herbicide and a tank mix partnerare to be appliedin multiple loads, pre-slurry the CHLORMET XP herbicide in clean water prior to adding to the tank. This will prevent the tank mix par tner from interfering with the dissolution of the CHLORMET XP herbicide. Do not use CHLORMET XP herbicide with spray additives that reduce the pH of the spray solution to below 3.0. APPLICATION METHOD Ground Application To obtain optimum spray distribution and thorough coverage, use flat-fan or low-volume flood nozzles. When using flat-fan nozzles, use a spray volume of at least 3 GPA. When usingflood nozzles on 30" spacings, use at least 10 GPA, flood nozzles no larger than TK10 (or the equivalent), and a pressure of at least 30 psi. For 40" nozzle spacings, use at least 13 GPA; for 60" spacings, use at least 20 GPA. It is essential to overlap the nozzles100% for all spacings. With “Raindrop” RA nozzles,do not use less than 20 GPA and overlap nozzles 100%. Use screens that are 50-mesh orl a r g e r . Aerial Application Use nozzle typesand arrangements that provide optimum spraydistribution and maximum coverage at 1 to 5 GPA. Use at least 3 GPA in Idaho, Oregon and Washington. When applying CHLORMET XP herbicide by air in areas near sensitive crops, use solid-stream nozzles oriented straight back. Chemigation Do not apply CHLORMET XP herbicide through any type of irrigation system. Before Spraying CHLORMET XP herbicide Spray equipment must be cleaned before CHLORMET XP herbicide is sprayed. Follow the cleanup procedures specified on the labels of previously applied products. If no directions are provided, follow the 6 steps outlined below.

26 At the End of the Day When multiple loads of CHLORMET XP herbicide are applied, it is advised that at the end of each day of spraying, the interior of the tank be rinsed with fresh water and then partially fille d, and the boom and hoses be flushed. This will prevent the bui ldup of dried pesticide deposits from accumulating in the application equipment. After Spraying CHLORMET XP herbicide and before Spraying Crops O ther Than Wheat Barley, Triticale, Fallow, or CRP To avoid subsequent injuryto desirable crops,thoroughly cleanall mixingand sprayequipment immediately following applications ofCHLORMET XP herbicideasfollows:

1. Drain tank; thoroughly rinse spray tanks, boom, and hoses with clean water. Loosen and physically remove any visible deposits.
2. Fill the tank with clean water and 1 gal of household ammonia * (contains at least 3% active ingredient) for every 100 gal of water. Flush the hoses, boom, and nozzles with the cleaning solution. Then add more water to completely fill the tank. Circulate the cleaning solution through the tank and hoses for at least 15 min. Flush the hoses, boom, and nozzles again with the cleaning solution, and then drain the tank.
3. Remove the nozzles and screens and clean separately in a bucket containing ammonia* and water.
4. Repeat step 2.
5. Rinse the tank, boom, and hoses with clean water.
6. If only ammonia is used as a cleaner, the rinsate solution ma y be applied back to the crop(s) advised on this label. Do not exceed the maximum labeled use rate. If other cleaners are used , consult the cleaner label for rinsate disposal instructions. I f no instructions are given, dispose of the rinsate on site or at an approved waste disposal facility.

• Equivalent amounts of an alternate-strength ammonia solution o r a cleaner which dissolves and removes sulfonylurea herbicide residues can be used in the cleanout procedure. Carefully read and follow the individual cleaner instructions. Notes:

1. Caution: Do not use chlorine bleach with ammonia, as dangerous gases will form. Do not clean equipment in an enclosed area.
2. Steam-cleaning aerial spray tanks is advised prior to performing the above cleanout procedure to facilitate the removal of a ny caked deposits.
3. When CHLORMET XP herbicide is tank mixed with other pesticides , examine all required cleanout procedures and follow the most rigorous procedure.
4. In addition to this cleanout procedure, follow all preapplicat ion cleanout guidelines on subsequently applied products as per the individual labels.
5. Where routine spraying practices include shared equipment fre quently being switched between applications of CHLORMET XP herbicide and applications of other pesticides to CHLORMET XP herbicide-sensitive crops during the same spray season, it is advised that a sprayer be dedicated to CHLORMET XP herbicide to further reduce the chance of crop injury.

27 MANDATORY SPRAY DRIFT MANAGEMENT Ground Boom Applications: • Apply with the nozzle height advised by the manufacturer, but n o more than 3 feet above the ground or crop canopy. • For applications prior to the emergence of crops and target we eds, applicators are required to use a Coarse or coarser droplet size (ASABE S572.1). • For all other applications, applicators are required to use a Medium or coarser droplet size (ASABE S572.1). • Do not apply when wind speeds exceed 10 miles per hour at the application site. • Do not apply during temperature inversions. Aerial Applications: • Do not release spray at a height greater than 10 feet above the vegetative canopy, unless a greater application height is necessary for pilot safety. • For applications prior to the emergence of crops and target we eds, applicators are required to use a Coarse or coarser droplet size (ASABE S572.1). • For all other applications, applicators are required to use a Medium or coarser droplet size (ASABE S572.1). • The boom length must not exceed 65% of the wingspan for airpla nes or 75% of the rotor blade diameter for helicopters. • Applicators must use one-half swath displacement upwind at the downwind edge of the field. • Nozzles must be oriented so the spray is directed toward the back of the aircraft. • Do not apply when wind speeds exceed 10 miles per hour at the application site. • Do not apply during temperature inversions. Boom-less Ground Applications: • Applicators are required to use a Medium or coarser droplet si ze (ASABE S572.1) for all applications. • Do not apply when wind speeds exceed 10 miles per hour at the application site. • Do not apply during temperature inversions. SPRAY DRIFT MANAGEMENT ADVISORIES THE APPLICATOR IS RESPONSIBLE FOR AVOIDING OFF-SITE SPRAY DRIFT . BE AWARE OF NEARBY NON-TARGET SITES AND ENVIRONMENTAL CONDITION S. IMPORTANCE OF DROPLET SIZE An effective way to reduce spray drift is to apply large drople ts. Use the largest droplets that provide target pest control. W hile applying larger droplets will reduce spray drift, the potential for drift will be greater if applications are made improperly or under unfavorable environmental conditions. Controlling Droplet Size – Ground Boom • Volume - Increasing the spray volume so that larger droplets ar e produced will reduce spray drift. Use the highest practical spray volume for the application. If a greater spray volume is needed, consider using a nozzle with a higher flow rate. • Pressure - Use the lowest spray pressure advised for the nozzle to produce the target spray volume and droplet size. • Spray Nozzle - Use a spray nozzle that is designed for the intended application. Consider using nozzles designed to reduce drift. Controlling Droplet Size – Aircraft • Adjust Nozzles - Follow nozzle manufacturers directions for sett ing up nozzles. Generally, to reduce fine droplets, nozzles must be oriented parallel with the airflow in flight. BOOM HEIGHT – Ground Boom Use the lowest boom height that is compatible with the spray nozzles that will provide uniform coverage. For ground equipment, the boom must remain level with the crop and have minimal bounce. RELEASE HEIGHT - Aircraft Higher release heights increase the potential for spray drift. When applying aerially to crops, do not release spray at a height greater than 10 ft above the crop canopy, unless a greater application height is necessary for pilot safety.

28 SHIELDED SPRAYERS Shielding the boom or individual nozzles can reduce spray drift. Consider using shielded sprayers. Verify that the shields are not interfering with the uniform deposition of the spray on the target area. TEMPERATURE AND HUMIDITY When making applications in hot and dry conditions, use larger droplets to reduce effects of evaporation. TEMPERATURE INVERSIONS Drift potential is high during a temperature inversion. Tempera ture inversions are characterized by increasing temperature with altitude and are common on nights with limited cloud cover and light to no wind. The presence of an inversion can be indicated by ground fog or by the movement of smoke from a ground source or an aircraft smoke generator. Smoke that layers and moves laterally in a concentrated cloud (under low wind conditions) indicates an inversion, while smoke that moves upward and rapidly dissipates indicates good vertical air mixing. Avoid applications during temperature inversions. WIND Drift potential generally increases with wind speed. AVOID APPL ICATIONS DURING GUSTY WIND CONDITIONS. Applicators need to be familiar with local wind patterns and terrain that could affect spray drift. HANDHELD TECHNOLOGY APPLICATIONS: • Take precautions to minimize spray drift. BOOM-LESS GROUND APPLICATIONS: Setting nozzles at the lowest effective height will help to reduce the potential for spray drift. DRIFT CONTROL ADDITIVES Using product compatible drift control additives can reduce drift potential. When a drift control additive is used, read and carefully observe cautionary statements and all other information on the additive’s label. If using an additive that increases viscosity, ensure that the nozzles and other application equipment will function properly with a viscous spray solution. Preferred drift control additives have been certified by the Council of Producers & Distributors of Agrotechnology (CPDA). IDENTIFICATION INFORMATION FOR PRODUCTS REFERENCED IN THIS LABEL REGISTERED PRODUCTS REFERENCED IN THIS LABEL Product Name Active Ingredient(s) EPA Registration Number Aim® EC herbicide carfentrazone-ethyl 279-3241 Ally® Extra SG herbicide (with Totalsol® soluble granules) thifensulfuron-methyl, tribenuron-methyl, metsulfuron-methyl 279-9603 Ally® XP herbicide metsulfuron-methyl 279-9575 Amber® Custom-Pak™ herbicide traisulfuron 100-768 Axial® XL herbicide pinoxaden 100-1256 Banvel® herbicide dicamba 66330-279 Bronate Advanced™ mcpa + bromoxynil 264-690 Curtail® Herbicide Clopyralid 62719-48 Clarity® herbicide dicamba 7969-137 Direx® 4L herbicide Diuron 66222-54 Discover® NG herbicide clodinafop-propargyl 100-1173 Everest® 3.0 herbicide flucarbazone-sodium 66330-429 Glean® XP herbicide chlorsulfuron 279-9600 Karmex® DF herbicide diuron 66222-51 PowerFlex® herbicide pyroxsulam 62719-569 Stinger® Herbicide Clopyralid 62719-73 WideMatch® herbicide clopyralid, fluroxypyr 62719-512

29 STORAGE AND DISPOSAL Do not contaminate water, food, or feed by storage and disposal. PESTICIDE STORAGE: Store product in original container only. Do not contaminate wa ter, other pesticides, fertilizer, food or feed in storage. Store in a cool, dry place. PESTICIDE DISPOSAL: Do not contaminate water, food, or feed by disposal. Waste resu lting from the use of this product must be disposed of on site or at an approved waste disposal facility. CONTAINER HANDLING: Refer to the Net Contents section of this p roduct’s labeling for the applicable “Nonrefillable Container” or “Refillable Container” designation. Nonrefillable Plastic and Metal Containers (Capacity Equal to o r Less Than 50 Pounds): Nonrefillable container. Do not reuse or refill this container. Triple rinse container ( or equivalent) promptly after emptying. Triple rinse as follows: Empty the remaining contents into application equipmen t or a mix tank. Fill the container 1/4 full with water and recap. Shake for 10 seconds. Pour rinsate into application equipment or a mix tank or store rinsate for later use or disposal. Drain for 10 seconds after the flow begins to drip. R epeat this procedure two more times. Then, for Plastic Containers, offer for recycling if available or puncture and dis pose of in a sanitary landfill, or by incineration. Do not burn, unless allowed by state and local ordinances. For Metal Containers, offer for recycling if available or reconditioning if appropriate, or puncture and dispose of in a sanitary landfill, or by other procedures approved by state and local authorities. Nonrefillable Plastic and Metal Containers (Capacity Greater Th an 50 Pounds): Nonrefillable container. Do not reuse or refill this container. Triple rinse container (or equivalent) promptly after emptying. Triple rinse as follows: Empty the remaining contents into application equipment or a mix tank. Fill the container 1/4 full with water. Replace and tighten closures. Tip container on its side and rol l it back and forth, ensuring at least one complete revolution, for 30 seconds. Stand the container on its end and tip it back and forth several times. Turn the container over onto its other end and tip it back and forth several times. Empty the rinsate into application equipment or a mix tank or store rinsate for later use or disposal. Repeat this procedure two more times. Th en, for Plastic Containers, offer for recycling if available or puncture and dispose of in a sanitary landfill, or by incine ration. Do not burn, unless allowed by state and local ordinances. For Metal Containers, offer for recycling if available or reconditioning if appropriate, or puncture and dispose of in a sanitary landfill, or by other procedures approved by state and local authorities. Nonrefillable Plastic and Metal Containers, e.g., Intermediate Bulk Containers [IBC] (Size or Shape Too Large to be Tipped, Rolled or Turned Upside Down): Nonrefillable container. Do not reuse or refill this container. Clean container promptly after emptying the contents from this contai ner into application equipment or mix tank and before final disposal using the following pressure rinsing procedure. Insert a lance fitted with a suitable tank cleaning nozzle into the container and ensure that the water spray thoroughly covers the top, bottom and all sides inside the container. The nozzle manufacturer generally p rovides instructions for the appropriate spray pressure, spray duration and/or spray volume. If the manufacturer’s instructions are not available, pressure rinse the container for at least 60 seconds using a minimum pressure of 30 PSI with a minimum rinse volume of 10% of the container volume. Drain, pour or pump rinsate into application equipment or rinsa te collection system. Repeat this pressure rinsing procedure two more times. Then, for Plastic Containers, offer f or recycling if available or puncture and dispose of in a sanitary landfill, or by incineration. For Metal Containers, offer for recycling if available or reconditioning if appropriate, or puncture and dispose of in a sanitary landfill, or by other procedures approved by state and local authorities. Nonrefillable Paper or Plastic Bags, Fiber Sacks including Flexible Intermediate Bulk Containers (FIBC) or Fiber Drums With Liners: Nonrefillable container. Do not reuse or refill this container. Completely empty paper or plastic bag, fiber sack or drum liner by shaking and tapping sides and bottom to loosen clinging particles. Empty residue into application or manufacturing equipment. Then offer for recyclin g if available or dispose of empty paper or plastic bag, fiber sack or fiber drum and liner in a sanitary landfill, or by incineration. Do not burn, unless allowed by state and local ordinances. Refillable Fiber Drums With Liners: Refillable container (fiber drum only). Refilling Fiber Drum: R efill this fiber drum with CHLORMET XP herbicide containing chlorsulfuron and met sulfuron methyl only. Do not reuse this fiber drum for any other purpose. Cleaning before refilling is the re sponsibility of the refiller. Completely empty liner by shaking and tapping sides and bottom to loosen clinging particl es. Empty residue into application or manufacturing equipment. Disposing of Fiber Drum and/or Liner: Do not reuse this fiber drum for any other purpose other than refilling (see preceding). Cleaning the container (liner and/or fiber drum) before final disposal is the responsibility of the person disposing of the container. Offer the liner for recycling if av ailable or dispose of liner in a sanitary landfill, or by incineration. Do not burn, unless allowed by state and local or dinances. If drum is contaminated and cannot be reused, dispose of it in the manner required for its liner. To clean th e fiber drum before final disposal, completely empty the fiber drum by shaking and tapping sides and bottom to loosen cl inging particles. Empty residue into application or manufacturing equipment. Then offer the fiber drum for recyclin g if available or dispose of in a sanitary landfill, or by incineration. Do not burn, unless allowed by state and local o rdinances.

30 NOTICE TO BUYER: Purchase of this material does not confer any rights under patents of countries outside of the United States. FMC, Ally, Aim, Clormet, Glean and TotalSol are trademarks or registered trademarks of FMC Corporation or an affiliate. Raindrop is a trademark of GP Companies Amber, Axial, and Discover, are trademarks of Syngenta Group Company Bronate is a trademark of Bayer Crop Science Curtail, PowerFlex, Stinger and Widematch are trademarks of the Dow Chemical Company Clarity is a trademark of BASF Corporation Banvel and Everest are trademarks of Arysta Lifesciences North America, L.L.C. Karmex and Direx are trademarks of Adama Group Company D-4039 052019 All Other Refillable Containers: Refillable container. Refilling Container: Refill this containe r with Chlormet XP herbicide containing chlorsulfuron and metsulfuron methyl only. Do not reuse this container for any other purpose. Cleaning before refilling is the responsibility of the refiller . Prior to refilling, inspect carefully for damage including cracks, punctures, abrasions, worn out threads and closure devices. If damage is found, do not use the container, contact FMC at the number below for instructions. Check for leaks after refilling and before transporting. If leaks are found, do not reuse or transport container, contact FMC at the number bel ow for instructions. Disposing of Container: Do not r e u s e t h i s c o n t a i n e r f o r a n y o t h e r p u r p o s e o t h e r t h a n r e f i l l i n g (see preceding). Cleaning the container before final disposal is the responsibility of the person disposing of the c ontainer. To clean the container before final disposal, use the following pressure rinsing procedure. Insert a lance fitted with a suitable tank cleaning nozzle into the container and ensure that the water spray thoroughly covers the top, bottom and all sides inside the container. The nozzle manufacturer generally provides instructions for the appropriate spray press ure, spray duration and/or spray volume. If the manufacturer’s instructions are not available, pressure rinse t he container for at least 60 seconds using a minimum pressure of 30 PSI with a minimum rinse volume of 10% of the co ntainer volume. Drain, pour or pump rinsate into application equipment or rinsate collection system. Repeat this pressure rinsing procedure two more times. Then, for Plastic Containers, offer for recycling if available or punctur e and dispose of in a sanitary landfill, or by incineration. Do not burn, unless allowed by state and local ordinances. For Metal Containers, offer for recycling if available or reconditioning if appropriate, or puncture and dispose of in a sanitary landfill, or by other procedures approved by state and local authorities. Outer Foil Pouches of Water Soluble Packets (WSP): Nonrefillable container. Do not reuse or refill this container. Offer for recycling if available or, dispose of the empty outer foil pouch in the trash as long as WSP is unbroken. If the outer pouch contacts the formulated product in any way, the pou ch must be triple rinsed with clean water. Add the rinsate to the spray tank and dispose of the outer pouch as described previously. Do not transport if this container is damaged or leaking. If the container is damaged, leaking or obsolete, or in the event of a major spill, fire or other emergency, contact CHEMTREC (Tr ansportation and Spills) at 1-800-424-9300, day or night.

31 CONDITIONS OF SALE AND LIMITATION OF WARRANTY AND LIABILITY Notice: Read the entire Directions for Use and Conditions of Sa le and Limitation of Warranty and Liability before buying or using this product. If the terms are not acceptable, return the product at once, unopened, and the purchase price will be refunded. The Directions for Use of this product must be followed careful ly. It is impossible to eliminate all risks inherently associated with the use of this product. Crop injury, ineffecti veness, or other unintended consequences may result because of such factors as manner of use or application, weathe r or crop conditions beyond the control or FMC or Seller. To the extent consistent with applicable law, all such risks shall be assumed by Buyer and User, and, to the extent consistent with applicable law, Buyer and User agree to hold FMC and Seller harmless for any claims relating to such factors. Seller warrants that this product conforms to the chemical description on the label and is reasonably fit for the purposes stated on the Directions for Use when used in accordance with the directions under normal conditions of use. TO THE EXTENT CONSISTENT WITH APPLICABLE LAW, FMC MAKE S NO WARRANTIES OF MERCHANTABILITY OR OF FITNESS FOR A PARTICULAR PURPOSE, NOR ANY OTHER EXPRESS OR IMPLIED WARRANTIES WITH RESPECT TO THE SELECTION, PU RCHASE, OR USE OF THIS PRODUCT. Any warranties, express or implied, having bee n made are inapplicable if this product has been used contrary to label instructions, or under abnormal conditions, or under conditions not reasonably foreseeable to (or beyond the control of) Seller or FMC, and, to the extent permitted by applicable law, Buyer assumes the risk of any such use. To the extent consistent with applicable law, FMC or Seller sha ll not be liable for any incidental, consequential or s p e c i a l d a m a g e s r e s u l t i n g f r o m t h e u s e o r h a n d l i n g o f t h i s p r o duct. TO THE EXTENT CONSISTENT WITH APPLICABLE LAW, THE EXCLUSIVE REMEDY OF THE USER OR BUYER, AND THE EXCLUSIVE LIABILITY OF FMC AND SELLER FOR ANY AND ALL CLAIMS, LOSSES, INJ URIES OR DAMAGES (INCLUDING CLAIMS BASED ON BREACH OF WARRANTY, CONTRACT, NEGLIGENCE, TORT, STRICT LIABILITY OR OTHERWISE) RESULTING FROM THE USE OR HANDLING OF T HIS PRODUCT, SHALL BE THE RETURN OF THE PURCHASE PRICE OF THE PRODUCT OR, AT THE E LECTION OF FMC OR SELLER, THE REPLACEMENT OF THE PRODUCT. This Condition of Sale and Limitation of Warranty and Liability may not be amended by any oral or written agreement. FMC Corporation, 2929 Walnut Street, Philadelphia, PA 19104 © 2011-2019 FMC Corporation. All rights reserved.