{
  "schema": 1,
  "meta": {
    "name": "Generic OBD-II",
    "make": "Any",
    "model": "Any OBD-II vehicle (1996+)",
    "years": "1996+",
    "engine": "any",
    "author": "OBDash project",
    "version": "1.0.0",
    "protocol": "auto",
    "notes": "Standard SAE J1979 Mode-01 PIDs only -- supported by essentially every OBD-II vehicle. Use as a base/starting point for a new vehicle profile, then add manufacturer-enhanced Mode-22 PIDs. Decodes are the SAE-standard formulas."
  },
  "presets": {
    "basic": ["RPM", "SPEED", "ECT", "IAT", "MAP", "THROTTLE", "LOAD", "BATT"]
  },
  "pids": [
    {"key": "RPM", "name": "Engine RPM", "mode": "01", "pid": "0C", "nbytes": 2, "formula": "(A*256+B)/4", "round": 0, "unit": "rpm", "group": "engine", "vmin": 0, "vmax": 8000, "confidence": "verified"},
    {"key": "SPEED", "name": "Vehicle Speed", "mode": "01", "pid": "0D", "nbytes": 1, "formula": "A", "round": 0, "unit": "km/h", "group": "driveline", "vmin": 0, "vmax": 255, "confidence": "verified"},
    {"key": "ECT", "name": "Engine Coolant Temp", "mode": "01", "pid": "05", "nbytes": 1, "formula": "A-40", "round": 0, "unit": "C", "group": "engine", "vmin": -40, "vmax": 215, "confidence": "verified"},
    {"key": "IAT", "name": "Intake Air Temp", "mode": "01", "pid": "0F", "nbytes": 1, "formula": "A-40", "round": 0, "unit": "C", "group": "air", "vmin": -40, "vmax": 215, "confidence": "verified"},
    {"key": "MAP", "name": "Intake Manifold Pressure", "mode": "01", "pid": "0B", "nbytes": 1, "formula": "A", "round": 0, "unit": "kPa", "group": "air", "vmin": 0, "vmax": 255, "confidence": "verified"},
    {"key": "MAF", "name": "Mass Air Flow", "mode": "01", "pid": "10", "nbytes": 2, "formula": "(A*256+B)/100", "round": 2, "unit": "g/s", "group": "air", "vmin": 0, "vmax": 655, "confidence": "verified"},
    {"key": "THROTTLE", "name": "Throttle Position", "mode": "01", "pid": "11", "nbytes": 1, "formula": "A*100/255", "round": 0, "unit": "%", "group": "engine", "vmin": 0, "vmax": 100, "confidence": "verified"},
    {"key": "LOAD", "name": "Calculated Load", "mode": "01", "pid": "04", "nbytes": 1, "formula": "A*100/255", "round": 0, "unit": "%", "group": "engine", "vmin": 0, "vmax": 100, "confidence": "verified"},
    {"key": "TIMING", "name": "Timing Advance", "mode": "01", "pid": "0E", "nbytes": 1, "formula": "A/2-64", "round": 1, "unit": "deg", "group": "engine", "vmin": -64, "vmax": 64, "confidence": "verified"},
    {"key": "VPCM", "name": "Module Voltage", "mode": "01", "pid": "42", "nbytes": 2, "formula": "(A*256+B)/1000", "round": 2, "unit": "V", "group": "power", "vmin": 0, "vmax": 16, "confidence": "verified"},
    {"key": "BATT", "name": "Battery (OBD port)", "mode": "atrv", "unit": "V", "group": "power", "vmin": 0, "vmax": 16, "confidence": "verified", "notes": "ELM327 ATRV pin voltage"}
  ],
  "dtcs": [],
  "actions": [
    {"key": "TESTER_PRESENT", "name": "Tester Present (ping)", "kind": "test", "risk": "safe",
     "description": "Sends a UDS keep-alive (3E 00). Confirms the ECU is responding on a CAN vehicle. No effect.",
     "steps": [{"send": "3E00"}], "success_msg": "ECU responded — module is alive."},
    {"key": "ECU_RESET", "name": "Reset ECU (soft reboot)", "kind": "reset", "risk": "caution",
     "description": "ISO 14229 ECUReset — reboots the engine control module (clears volatile adaptations).",
     "warning": "Reboots the ECM. Do this with the ENGINE OFF, key in RUN. The engine would stall if running, and comms drop briefly. UDS/CAN vehicles only.",
     "steps": [{"send": "1101"}], "success_msg": "ECU reset acknowledged."}
  ]
}