2661 lines
133 KiB
Markdown
2661 lines
133 KiB
Markdown
# CHEETAH HERBICIDE
|
||
|
||
- EPA Reg No: **71368-112**
|
||
- Registrant: NUFARM, INC.
|
||
- Signal word: Warning
|
||
- Active ingredients: Glufosinate (24.5%)
|
||
- Label accepted: 2026-09-02
|
||
- Source PDF: https://www3.epa.gov/pesticides/chem_search/ppls/071368-00112-20260902.pdf
|
||
|
||
---
|
||
September 2, 2026
|
||
Nikki Benson
|
||
Regulatory Manager
|
||
Nufarm, Inc.
|
||
11901 South Austin Avenue
|
||
Alsip, IL 60803
|
||
Subject: Approval of Label Amendment; On ly Indicated Changes Reviewed – Label typos
|
||
Product Name: Cheetah® Herbicide
|
||
EPA Registration Number: 71368-112
|
||
Application Date: 05/06/2026
|
||
Case Number: 00696248
|
||
Dear Nikki Benson:
|
||
The amended label referred to above, submitted in connection with registration under the
|
||
Federal Insecticide, Fungicide, and Rodenticide Act (FIFRA), as amended, is acceptable.
|
||
However, EPA reviewed only the label changes highlighted, marked, or otherwise indicated on
|
||
the submitted label. Any other changes to the previously approved label that were not clearly
|
||
highlighted, marked, or otherwise indicated in your submission were not reviewed and may
|
||
form the basis of regulatory and/or enforcement action if later discovered by the Agency.
|
||
Further, submission of a label amendment application with unidentified changes may be
|
||
considered a knowing submission of false information to the Agency. This approval does not
|
||
affect any conditions that were previously imposed on this registration. You continue to be
|
||
subject to existing conditions on your registration and any deadlines connected with them.
|
||
The label submitted with the application has been stamped “Accepted Only Indicated Revisions
|
||
Reviewed” and is enclosed for your records.
|
||
This labeling supersedes all previously accepted labeling. You must submit one copy of the final
|
||
printed labeling before you release the product for shipment with the new labeling. In
|
||
accordance with 40 C.F.R. § 152.130(c), you may distribute or sell this product under the
|
||
previously approved labeling for 18 months from the date of this letter. After 18 months, you
|
||
may only distribute or sell this product if it bears this new revised labeling or subsequently
|
||
approved labeling. “To distribute or sell” is defined under FIFRA section 2(gg) and its
|
||
implementing regulation at 40 C.F.R. § 152.3.
|
||
|
||
Page 2 of 2
|
||
EPA Reg. No. 71368-112
|
||
Case Number 00696248
|
||
|
||
Should you wish to add/retain a reference to the company’s website on your label, then please
|
||
be aware that the website becomes labeling under FIFRA and is subject to review by the
|
||
Agency. If the website contains any false or misleading statement, design, or graphic, the
|
||
product may be misbranded and unlawful to sell or distribute under FIFRA Sections 2(q)(1)(A)
|
||
and 12(a)(1)(E). 40 C.F.R. § 156.10(a)(5) lists examples of statements EPA may consider false or
|
||
misleading. In addition, regardless of whether a website is referenced on the product label,
|
||
claims made as part of the product’s sale or distribution may not substantially differ from those
|
||
claims approved through the registration process under FIFRA Section 12(a)(1)(B). Therefore,
|
||
should the Agency find or if it is brought to our attention that a website contains false or
|
||
misleading statements or claims substantially differing from the EPA approved registration, the
|
||
product will be referred to the EPA’s Office of Enforcement and Compliance Assurance.
|
||
|
||
Your release for shipment of the product constitutes acceptance of these conditions. If these
|
||
conditions are not complied with, the registration will be subject to cancellation in accordance
|
||
with FIFRA section 6.
|
||
|
||
If you have any questions, please contact Andrew Watkins at 919-541-7940 or at
|
||
Watkins.andrew@epa.gov.
|
||
|
||
S i n c e r e l y ,
|
||
Kable Bo Davis
|
||
Kable Bo Davis; Senior Advisor
|
||
O f f i c e o f P e s t i c i d e P r o g r a m s
|
||
R e g i s t r a t i o n D i v i s i o n ; I m m e d i a t e O f f i c e
|
||
|
||
|
||
|
||
Enclosure
|
||
|
||
ϭ
|
||
|
||
GLUFOSINATE GROUP 10 HERBICIDE
|
||
|
||
Cheetah® Herbicide
|
||
Cheetah is a non-selective herbicide that provides control of a broad spectrum of broadleaf weeds and grassy weeds.
|
||
Cheetah is registered for use: as a burndown treatment prior to planting or prior to emergence of canola, corn, cotton, sweet c orn,
|
||
soybean and sugar beets; post emergence weed control herbicide to be applied on crops containing the glufosinate-resistant gene ;
|
||
post emergence weed control in cotton when applied with a hooded sprayer in-crop; post emergence weed control in listed tree,
|
||
olives, vine, and berry crops; applied for potato vine desiccation; as a nonselective postemergent herbicide
|
||
|
||
ACTIVE INGREDIENT:
|
||
Glufosinate-ammonium*…………………………………………………………………24.5%**
|
||
OTHER INGREDIENTS……………………………………………………………………75.5%
|
||
|
||
TOTAL 100.0%
|
||
*CAS Number 77182-82-2
|
||
**Equivalent to 2.34 pounds of active ingredient per U.S. gallon.
|
||
[For < 5 Gallon Containers:] [Shake Well Before Use]
|
||
[For > 5 Gallon Containers:] [Shake Well, Agitate or Recirculate Before Use]
|
||
KEEP OUT OF REACH OF CHILDREN
|
||
CAUTION
|
||
Si usted no entiende la etiqueta busque a alguien para que se la explique a usted en detalle.
|
||
(If you DO NOT understand the label find someone to explain it to you in detail)
|
||
See back [side][panel][below][next page][inside booklet][booklet] for [First Aid][and][additional]
|
||
Precautionary Statements [and][Directions for Use]
|
||
For Medical Emergencies Call (877) 325-1840
|
||
For Chemical Spill, Leak, Fire, or Exposure, Call CHEMTREC (800) 424-9300
|
||
|
||
FIRST AID
|
||
IF ON SKIN OR
|
||
CLOTHING
|
||
• Take off contaminated clothing.
|
||
• Rinse skin immediately with plenty of water for 15 to 20 minutes.
|
||
• Call a poison control center or doctor for treatment advice.
|
||
IF SWALLOWED • Call a poison control center or doctor immediately for treatment advice.
|
||
• Have person sip a glass of water if able to swallow.
|
||
• DO NOT induce vomiting unless told to do so by a poison control center or doctor.
|
||
• DO NOT give anything by mouth to an unconscious person.
|
||
IF IN EYES • Hold eye open and rinse slowly and gently with water for 15 to 20 minutes.
|
||
• Remove contact lenses, if present, after the first 5 minutes, then continue rinsing
|
||
eye.
|
||
• Call a poison control center or doctor for treatment advice.
|
||
IF INHALED • Move person to fresh air.
|
||
• If person is not breathing, call 911 or an ambulance, then give artificial respiration,
|
||
preferably mouth-to-mouth if possible.
|
||
• Call a poison control center or doctor for treatment advice.
|
||
HOT LINE NUMBER
|
||
Have the product container or label with you when calling a poison control center or doctor or going for
|
||
treatment. You may also contact Nufarm at 1-877-325-1840 for emergency medical treatment
|
||
information. For Chemical Spill, Leak, Fire, or Exposure, Call CHEMTREC (800) 424-9300.
|
||
NOTE TO PHYSICIAN
|
||
If this product is ingested, endotracheal intubation and gastric lavage should be performed as soon as
|
||
possible, followed by charcoal and sodium sulfate administration.
|
||
|
||
EPA REG. NO. 71368-112 MANUFACTURED FOR
|
||
EPA EST. NO. NUFARM, INC.
|
||
11901 SOUTH AUSTIN AVENUE
|
||
ALSIP, IL 60803
|
||
NET CONTENTS: GAL. ( Liters)
|
||
[Designation as “NONREFILLABLE” or “REFILLABLE” for containers >5]
|
||
71368-112
|
||
09/02/2026
|
||
|
||
Ϯ
|
||
|
||
PRECAUTIONARY STATEMENTS
|
||
HAZARDS TO HUMANS AND DOMESTIC ANIMALS
|
||
CAUTION
|
||
Harmful if absorbed through skin, swallowed. Causes moderate eye irritation. Avoid contact with skin, eyes
|
||
or clothing and breathing vapor. Wash thoroughly with soap and water after handling and before eating,
|
||
drinking, chewing gum, using tobacco or using the toilet. Remove and wash contaminated clothing before
|
||
reuse. Prolonged or frequently repeated skin contact may cause allergic reactions in some individuals.
|
||
|
||
Personal Protective Equipment (PPE)
|
||
x All handlers must wear long-sleeved shirts, long pants, shoes and socks.
|
||
x Applicators using groundboom equipment with open cabs to treat cotton must wear long-sleeve
|
||
shirts, long pants, shoes, and socks plus chemical-resistant gloves.
|
||
x Mixer/loaders supporting ground boom applications to com, canola, soybean, cotton, citrus fruit,
|
||
pome fruit, stone fruit, and olives must wear long-sleeve shirts, long pants, shoes, and socks plus
|
||
chemical resistant gloves.
|
||
Follow the manufacturer’s instructions for cleaning/maintaining PPE. If no such instructions for washables
|
||
exist, use detergent and hot water. Keep and wash PPE separately from other laundry.
|
||
|
||
Applicators using ground boom equipment with open cabs to treat cotton must wear long-sleeve shirts, long
|
||
pants, shoes, and socks plus chemical-resistant gloves.
|
||
|
||
Mixer/loaders supporting ground boom applications corn, canola, soybean, cotton, citrus fruit, pome fruit,
|
||
stone fruit, and olives must wear long-sleeve shirts, long pants, shoes, and socks plus chemical-resistant
|
||
gloves.
|
||
|
||
|
||
USER SAFETY RECOMMENDATIONS
|
||
Users should:
|
||
• Remove clothing/PPE immediately if pesticide gets inside. Then wash thoroughly and put on clean
|
||
clothing.
|
||
• Remove PPE immediately after handling Cheetah. Wash the outside of gloves before removing. As
|
||
soon as possible, wash thoroughly and change into clean clothing.
|
||
|
||
ENGINEERING CONTROLS STATEMENT
|
||
When handlers use closed systems, enclosed cabs, or aircraft in a manner that meets the requirements
|
||
listed in the Worker Protection Standard (WPS) for agricultural pesticides [(40 CFR 170.240(d)(4-6)], the
|
||
handler PPE requirements may be reduced or modified as specified in the WPS.
|
||
|
||
ENVIRONMENTAL HAZARDS
|
||
DO NOT apply directly to water or to areas where surface water is present. DO NOT apply to intertidal
|
||
areas below the mean high water mark. DO NOT contaminate water by cleaning of equipment or disposal
|
||
of equipment washwaters or rinsate.
|
||
|
||
This pesticide is toxic to vascular plants and must be used strictly in accordance with the drift and run-off
|
||
precautions on this label in order to minimize off-site exposures.
|
||
|
||
Under some conditions, Cheetah may have a potential to run-off to surface water or adjacent land. Where
|
||
possible, use methods which reduce soil erosion, including no till, limited till and contour plowing; these
|
||
methods also reduce pesticide run-off. Use of vegetation filter strips along rivers, creeks, streams, wetlands,
|
||
etc. or on the downhill side of fields where run-off could occur to minimize water run-off is recommended.
|
||
|
||
PHYSICAL AND CHEMICAL HAZARDS
|
||
DO NOT mix or allow contact with oxidizing agents. Hazardous chemical reaction may occur.
|
||
Combustible. DO NOT use or store near heat or open flame.
|
||
|
||
ϯ
|
||
|
||
DIRECTIONS FOR USE
|
||
It is a violation of Federal law to use Cheetah in a manner inconsistent with its labeling.
|
||
|
||
DO NOT use Cheetah until you have read the entire label.
|
||
DO NOT apply Cheetah in a way that will contact workers or other persons, either directly or through drift.
|
||
Only protected handlers may be in the area during application.
|
||
For any requirements specific to your State or Tribe, consult the agency responsible for pesticide regulation.
|
||
In the State of New York Only: Not For Use In Nassau and Suffolk Counties.
|
||
|
||
|
||
AGRICULTURAL USE REQUIREMENTS
|
||
Use Cheetah only in accordance with its labeling and with the Worker Protection Standard, 40 CFR part
|
||
170. This Standard contains requirements for the protection of agricultural workers on farms, forests,
|
||
nurseries, and greenhouses; and handlers of agricultural pesticides. It contains requirements for training,
|
||
decontamination, notification, and emergency assistance. It also contains specific instructions and
|
||
exceptions pertaining to the statements on this label about personal protective equipment (PPE), and
|
||
restricted
|
||
-entry intervals. The requirements in this box only apply to uses of Cheetah that are covered by
|
||
the Worker Protection Standard.
|
||
Restricted entry-interval (REI) 12 hours for all post-application activities
|
||
Restricted entry -interval (REI) 12 hours for all post- application activities, with the following
|
||
exception: Workers engaged in scouting or irrigation activities in corn, canola, and soybean is
|
||
4 days. The REI for workers to move irrigation
|
||
piping is 7 days for all crops.
|
||
PPE required for early entry to treated areas that is permitted under the Worker Protection Standard and
|
||
that involves contact with anything that has been treated, including plants, soil, or water, is:
|
||
x Coveralls worn over short-sleeved shirt and short pants;
|
||
x Chemical resistant gloves including barrier laminate, butyl rubber 14 mils, nitrile rubber >14 mils,
|
||
neoprene rubber > 14 mils, polyvinyl chloride (PVC) > 14 mils, or Viton > 14 mils, and
|
||
x Chemical resistant footwear plus socks;
|
||
x Protective eyewear (goggles, face shield or safety glasses).
|
||
|
||
IMPORTANT CROP SAFETY INFORMATION READ BEFORE USING CHEETAH
|
||
Cheetah may be applied as a burndown treatment prior to planting or prior to crop emergence of any
|
||
canola, sweet corn[1], corn, cotton, olive, soybean or sugar beet.
|
||
POST EMERGENT TREATMENTS
|
||
Post emergence row crop applications of Cheetah may be made only to crops resistant to glufosinate.
|
||
Tank mixtures of Cheetah with other products may impact crop resistance and increase risk of crop
|
||
injury. The basis of selectivity of Cheetah herbicide in glufosinate-resistant crops is the presence of a
|
||
gene that makes crops not sensitive to glufosinate. Crops not containing the glufosinate-resistant gene
|
||
will be sensitive to Cheetah and severe crop injury and/or death may occur. DO NOT allow spray to
|
||
contact foliage or green tissue of desirable vegetation other than crops containing the glufosinate-
|
||
resistant trait.
|
||
Post emergent applications of Cheetah may be applied to crops not containing the glufosinate-resistant
|
||
gene using a hooded sprayer.
|
||
TREE, NUT, VINE AND BERRY TREATMENTS
|
||
Applications to trees, vines and berries must avoid contact of Cheetah solution, spray drift or mist with
|
||
green bark, stems or foliage as injury may occur to trees, berries and vines. Only trunks with callused
|
||
mature brown bark must be sprayed unless protected from spray contact by nonporous wraps, grow
|
||
tubes or waxed containers. Contact of Cheetah with parts of trees, berries or vines other than mature
|
||
brown bark can result in serious damage.
|
||
[1 – Not for use in California]
|
||
|
||
ϰ
|
||
|
||
NON-AGRICULTURAL USE REQUIREMENTS
|
||
The requirements in this box apply to uses of this product that are NOT within the scope of the Worker
|
||
Protection Standard for agricultural pesticides (40 CFR Part 170). The WPS applies when this product
|
||
is used to produce agricultural plants on farms, forests, or greenhouses.
|
||
DO NOT enter or allow others to enter treated areas until sprays have dried.
|
||
|
||
PRODUCT INFORMATION
|
||
Cheetah is a water-soluble herbicide for application as a foliar spray for the control of a broad spectrum of
|
||
emerged annual and perennial grass and broadleaf weeds in a variety of crops.
|
||
Cheetah is registered for use:
|
||
x as a burndown treatment prior to planting or prior to emergence of canola, corn, cotton, sweet corn,
|
||
olive, soybean and sugar beets
|
||
x post emergence weed control herbicide to be applied on crops containing the glufosinate-resistant
|
||
gene, including canola, soybean, corn, sweet corn and cotton
|
||
x post emergence weed control in cotton when applied with a hooded sprayer in-crop
|
||
x post emergence weed control in listed tree, olives, vine, and berry crops
|
||
x applied for potato vine desiccation.
|
||
Many glufosinate-resistant seed trade names are available. Contact the seed manufacturer or seed
|
||
distributor to determine if the seed variety is designated and supported as containing the
|
||
glufosinate-resistant trait.
|
||
It is important to always follow a responsible integrated weed management program.
|
||
Contact your local agronomic advisor for more specific information on integrated weed management in your
|
||
area.
|
||
|
||
Cheetah is only foliar-active with little or no activity in soil. Weeds that emerge after application will not be
|
||
controlled.
|
||
|
||
Apply Cheetah to actively growing weeds as described in the WEED CONTROL FOR ROW CROPS
|
||
section to get maximum weed control. Uniform, thorough spray coverage is necessary to achieve consistent
|
||
weed control. Necrosis of leaves and young shoots occur within 2 to 4 days after application under good
|
||
growing conditions.
|
||
• Cheetah is rainfast 4 hours after application to most weed species; therefore, rainfall within 4 hours may
|
||
necessitate retreatment or may result in reduced weed control.
|
||
• Make applications between dawn and 2 hours before sunset to avoid the possibility of reduced
|
||
lambsquarters and velvetleaf control.
|
||
• Consult your local Cooperative Extension Service or Nufarm, Inc. representative for guidelines on the
|
||
optimum application timing for Cheetah in your region.
|
||
• Weed control may be reduced if application is made when heavy dew, fog, and mist/rain are present; or
|
||
when weeds are under stress due to environmental conditions including drought, cool temperatures, or
|
||
extended periods of cloudiness.
|
||
• To maximize weed control, DO NOT cultivate from 5 days before an application to 7 days after an
|
||
application.
|
||
|
||
|
||
ROTATIONAL CROP RESTRICTIONS*
|
||
Rotational crop planting intervals following application of Cheetah are listed below. Failure to comply with
|
||
these restrictions may result in illegal residues in rotated crops.
|
||
|
||
|
||
Rotational Crop
|
||
Plant Back Interval
|
||
(Minimum Rotational Crop
|
||
Planting Interval from Last
|
||
Application)
|
||
Canola, Corn, Cotton, Soybeans, Sweet Corn, and Sugar beets May be planted at any time
|
||
Root and Tuber Vegetables, Leafy Vegetables, Brassica Leafy
|
||
Vegetables and Small Grains (Barley, Buckwheat, Oats, Rye,
|
||
Teosinte, Triticale, and Wheat)
|
||
70 days
|
||
|
||
ϱ
|
||
|
||
All other crops 180 days
|
||
*See Application Directions for Potato Vine Desiccation for Rotational Crop Restrictions specifically after application
|
||
of Cheetah to potatoes.
|
||
|
||
WEED RESISTANCE MANAGEMENT
|
||
For resistance management, Cheetah contains a Group 10 herbicide –Glufosinate-ammonium. Any weed
|
||
population may contain or develop plants naturally resistant to Cheetah and other Group 10 herbicides.
|
||
The resistant biotypes may dominate the weed population if these herbicides are used repeatedly in the
|
||
same field. Appropriate resistance management strategies should be followed.
|
||
|
||
When herbicides that affect the same biological site of action are used repeatedly over several years to
|
||
control the same weed species in the same field, naturally-occurring resistant biotypes may survive a
|
||
correctly applied herbicide treatment, propagate, and become dominant in that field. Adequate control of
|
||
these resistant weed biotypes cannot be expected. If weed control is unsatisfactory, it may be necessary
|
||
to retreat the problem area using a product affecting a different site of action.
|
||
|
||
To delay herbicide resistance take one or more of the following steps:
|
||
|
||
• Rotate the use of Cheetah or other Group 10 herbicides within a growing season sequence or among
|
||
growing seasons with different herbicide groups that control the same weeds in a field.
|
||
|
||
• Use tank mixtures with herbicides from a different group if such use is permitted; where information on
|
||
resistance in target weed species is available, use the less resistance-prone partner at a rate that will control
|
||
the target weed(s) equally as well as the more resistance-prone partner. Consult your local extension
|
||
service or certified crop advisor if you are unsure as to which active ingredient is currently less prone to
|
||
resistance.
|
||
|
||
• Adopt an integrated weed-management program for herbicide use that includes scouting and uses
|
||
historical information related to herbicide use and crop rotation, and that considers tillage ( or other
|
||
mechanical control methods), cultural ( e.g., higher crop seeding rates; precision fertilizer application
|
||
method and timing to favor the crop and not the weeds), biological (weed-competitive crops or varieties)
|
||
and other management practices.
|
||
|
||
• Scout before and after herbicide application to monitor weed populations for early signs of resistance
|
||
development. Indicators of possible herbicide resistance include: (1) failure to control a weed species
|
||
normally controlled by the herbicide at the dose applied, especially if control is achieved on adjacent weeds;
|
||
(2) a spreading patch of non-controlled plants of a particular weed species; (3) surviving plants mixed with
|
||
controlled individuals of the same species. If resistance is suspected, prevent weed seed production in the
|
||
affected area by an alternative herbicide from a different group or by a mechanical method including hoeing
|
||
or tillage. Prevent movement of resistant weed seeds to other fields by cleaning harvesting and tillage
|
||
equipment when moving between fields, and planting clean seed.
|
||
|
||
• If a weed pest population continues to progress after treatment with this product, discontinue use of this
|
||
product, and switch to another management strategy or herbicide with a different mode of action, if
|
||
available.
|
||
|
||
• Contact your local extension specialist or certified crop advisors for additional pesticide resistance-
|
||
management and/or integrated weed-management recommendations for specific crops and weed biotypes.
|
||
|
||
• For further information or to report non-performance or suspected resistance, contact Nufarm at 1-800-
|
||
345-3330
|
||
|
||
It is advisable to keep accurate records of pesticides applied to individual fields to help obtain information
|
||
on the spread and dispersal of resistant biotypes. Contact your local sales representative, crop advisor, or
|
||
extension agent to find out if suspected resistant weeds to this MOA have been found in your region. DO
|
||
|
||
ϲ
|
||
|
||
NOT assume that each listed weed is being controlled by this mechanisms of action. Co-formulated active
|
||
ingredients are intended to broaden the spectrum of weeds that are controlled. Some weeds may be
|
||
controlled by only one of the active ingredient in this product.
|
||
|
||
Suspected herbicide-resistant weeds may be identified by these indicators:
|
||
* Failure to control a weed species normally controlled by the herbicide at the dose applied,
|
||
especially if control is achieved on adjacent weeds;
|
||
* A spreading patch of non-controlled plants of a particular weed species; and
|
||
* Surviving plants mixed with controlled individuals of the same species.
|
||
|
||
|
||
INTEGRATED PEST MANAGEMENT
|
||
Nufarm advises the use of Integrated Pest Management (IPM) programs to control pests. This product may
|
||
be used as part of an Integrated Pest Management (IPM) program which can include biological, cultural,
|
||
and genetic practices aimed at preventing economic pest damage. Application of this product needs to be
|
||
based on IPM principles and practices including field scouting or other detection methods, correct target
|
||
pest identification, population monitoring, and treating when target pest populations reach locally
|
||
determined action thresholds. Consult your state cooperative extension service, professional consultants
|
||
or other qualified authorities to determine appropriate action treatment threshold levels for treating specific
|
||
pest/crop or site systems in your area.
|
||
|
||
|
||
WEED CONTROL FOR ROW CROPS
|
||
Rates in fluid ounce of formulated product per acre for the control of weeds as shown in the weed control
|
||
tables. In weed populations with mixed species, apply at a rate needed for the species targeting less than
|
||
three inch weeds.
|
||
Table 1. Broadleaf Weeds Controlled
|
||
(including Glyphosate-, Triazine-, PPO-, ALS-, HPPD-, and Auxin-Resistant Biotypes)
|
||
|
||
|
||
|
||
Common Name
|
||
|
||
|
||
|
||
Scientific Name
|
||
22.0 Fl Oz/A
|
||
(0.40 lb ai/A)
|
||
29.0 – 43.0 Fl Oz/A 1
|
||
(0.53-0.79 lb ai/A)
|
||
C=Control
|
||
S = Suppression
|
||
C=Control
|
||
S = Suppression
|
||
Amaranth, Palmer Amaranthus palmeri Not Advised C
|
||
Anoda, spurred Anoda cristata C C
|
||
Beggarweed, Florida Desmodium tortuosum C C
|
||
Black medic Medicago lupulina L. C C
|
||
Blueweed, Texas Helianthus ciliaris DC. C C
|
||
Buckwheat, wild Polygonum convolvulus C C
|
||
Buffalobur Solanum cornutum C C
|
||
Burcucumber Sicyos angulatus C C
|
||
Canola, volunteer 2 Brassica spp. C 2 C 2
|
||
Catchweed bedstraw
|
||
(cleavers)
|
||
Galium aparine L. C C
|
||
Carpetweed Mollugo verticillata C C
|
||
Chickweed, common Stellaria media C C
|
||
Cocklebur, common Xanthium strumarium C C
|
||
Copperleaf, hophornbeam Acalypha ostryaefolia C C
|
||
Cotton, volunteer 2 Gossypium spp. C 2 C 2
|
||
Croton, tropic Croton glandulosus C C
|
||
Croton, woolly Croton capitatus C C
|
||
Eclipta Eclipta alba C C
|
||
Devil’s claw Proboscidea Louisiana C C
|
||
Fleabane, annual Erigeron annuus C C
|
||
Galinsoga, hairy Galinsoga ciliate C C
|
||
Galinsoga, small flower Galinsoga parviflora C C
|
||
|
||
ϳ
|
||
|
||
Groundcherry, cutleaf Physalis angulate C C
|
||
Geranium, cutleaf Geranium dissectum L. C C
|
||
Hempnettle Galeopsis spp. C C
|
||
Horsenettle, Carolina 3 Solanum carolinense C 3 C 3
|
||
Jimsonweed Datura stramonium C C
|
||
Knotweed Polygonum spec. C C
|
||
Kochia Kochia scoparia C C
|
||
Ladysthumb Polygonum persicaria C C
|
||
Lambsquarters, common Chenopodium album C C
|
||
Mallow, common Malva spec. C C
|
||
Mallow, Venice Hibiscus trionum C C
|
||
Marestail 4 Conyza Canadensis S C
|
||
Marsh-elder, annual Iva annua C C
|
||
Morningglory, entireleaf Ipomoea hederacea var.
|
||
intergriuscula
|
||
|
||
C
|
||
|
||
C
|
||
Morningglory, ivyleaf Ipomoea hederacea C C
|
||
Morningglory, pitte Ipomoea lacunose C C
|
||
Morningglory, sharppod Ipomoea cordatotriloba C C
|
||
Morningglory, Smallflower Jacquemontia tamnifolia C C
|
||
Morningglory, tall lpomoea purpurea C C
|
||
Mustard, wild Sinapis arvensis C C
|
||
Nightshade, black Solanum nigrum C C
|
||
Nightshade, eastern black Solanum ptycanthum C C
|
||
Nightshade, hairy Solanum sarrachoides C C
|
||
Pennycress Thlaspi arvense C C
|
||
Pigweed, redroot Amaranthus retroflexus C C
|
||
Pigweed, prostrate Amaranthus blitoides C C
|
||
Pigweed, spiny Amaranthus spinosus C C
|
||
Pigweed, smooth Amaranthus hybridus C C
|
||
Pigweed, tumble Amaranthus albus C C
|
||
Table 1. (cont.) Broadleaf Weeds Controlled Table 1. Broadleaf Weeds Controlled
|
||
(including Glyphosate-, Triazine-, PPO-, ALS-, HPPD-, and Auxin-Resistant Biotypes)
|
||
|
||
|
||
|
||
Common Name
|
||
|
||
|
||
|
||
Scientific Name
|
||
22.0 Fl Oz/A
|
||
(0.40 lb ai/A)
|
||
29.0 – 43.0 Fl Oz/A 1
|
||
(0.53-0.79 lb ai/A)
|
||
C=Control
|
||
S = Suppression
|
||
C=Control
|
||
S = Suppression
|
||
Puncturevine Tribulus terrestris C C
|
||
Purslane, common Portulaca oleracea C C
|
||
Pusley, Florida Richardia scabra S C
|
||
Ragweed, common Ambrosia artemisiifolia C C
|
||
Ragweed, giant Ambrosia trifida C C
|
||
Senna coffee Cassia occidentalis C C
|
||
Sesbania, hemp Sesbania herbacea C C
|
||
Shepherd’s-Purse Capsella bursa-pastoris C C
|
||
Sicklepod (java bean) Senna obtusifolia C C
|
||
Sida, prickly Sida spinosa L. C C
|
||
Smartweed, Pennsylvania Polygonum
|
||
pensylvanicum
|
||
C C
|
||
Smell melon Cucumis melo L. var.
|
||
Dudaim
|
||
C C
|
||
Sowthistle, annual Sonchus oleraceus L. C C
|
||
Soybeans, volunteer 2 Glycine max C 2 C 2
|
||
Spurge, prostrate Euphorbia humifusa C C
|
||
Spurge, spotted Euphorbia maculate L. C C
|
||
Starbur, bristly Acanthospermum
|
||
hispidum
|
||
C C
|
||
|
||
ϴ
|
||
|
||
Sunflower, common Helianthus annuus C C
|
||
Sunflower, prairie Corythucha pura C C
|
||
Sunflower, volunteer Girassol C C
|
||
Thistle, Russian 3 Salsola kali S 3 C 3
|
||
Velvetleaf Abutilon theophrasti C C
|
||
Waterhemp, common Amaranthus rudis Not Advised C
|
||
Waterhemp, tall Amaranthus tuberculatus Not Advised C
|
||
1 Maximum rate on canola, field corn, sweet corn and soybean in California is 36 fl oz/A (0.66 lb ai/A).
|
||
2 Volunteer glufosinate-resistant crops from the previous year will not be controlled.
|
||
3 May require sequential applications for control.
|
||
4 For optimum control apply Cheetah on 6” marestail
|
||
|
||
|
||
|
||
Table 2. Grass Weeds Controlled
|
||
(including Glyphosate-, Triazine-, PPO-, ALS-, HPPD-, and Auxin-Resistant Biotypes)
|
||
|
||
|
||
|
||
Common Name
|
||
|
||
|
||
|
||
Scientific Name
|
||
22.0 Fl Oz/A
|
||
(0.40 lb ai/A)
|
||
29.0 – 43.0 Fl Oz/A 1
|
||
(0.53-0.79 lb ai/A)
|
||
C=Control
|
||
S = Suppression
|
||
C=Control
|
||
S = Suppression
|
||
Barley, volunteer 3 C 3 C 3
|
||
Barnyardgrass Echinochloa spec. C C
|
||
Bluegrass, annual Poa annua L. C C
|
||
Corn, volunteer 2 Zea mays L. C 2 C 2
|
||
Crabgrass, large 4 Digitaria sanguinalis C 4 C 4
|
||
Crabgrass, smooth 4 Digitaria ischaemum C 4 C 4
|
||
Cupgrass, woolly Eriochloa villosa C C
|
||
Foxtail, bristly Setaria verticillata C C
|
||
Foxtail, giant Setaria faberi C C
|
||
Foxtail, green Setaria viridis C C
|
||
Foxtail, robust purple Setaria viridis C C
|
||
Foxtail, yellow 4 Pennisetum glaucum C 4 C 4
|
||
Goosegrass 3 Eleusine indica C 3 C 3
|
||
Johnsongrass, seedling Sorghum halepense C C
|
||
Junglerice Echinochloa colonum C C
|
||
Millet, wild-proso Panicum miliaceum L. C C
|
||
Millet, proso volunteer Milium vernale C C
|
||
Oat, wild 4 Avena fatua C 4 C 4
|
||
Panicum, fall Panicum
|
||
dichotomiflorum
|
||
C C
|
||
Panicum, Texas Panicum texanum C C
|
||
Rice, red Oryza sativa L. C C
|
||
|
||
Sandbur, field 4 Cenchrus pauciflorus S 4 C 4
|
||
Shattercane Sorghum vulgare
|
||
PERS.
|
||
C C
|
||
Signalgrass, broadleaf Brachiaria platyphylla C C
|
||
Sprangletop Leptochloa spec. C C
|
||
Sorghum, volunteer Sorghum spp. C C
|
||
Stinkgrass Eragrostis cilianensis C C
|
||
Wheat, volunteer 3, 4 Triticum spec. C 3, 4 C 3, 4
|
||
Witchgrass Panicum virgatum L.
|
||
capillare
|
||
C C
|
||
1 Maximum rate on canola, field corn, sweet corn and soybean in California is 36 fl oz/A (0.66 lb ai/A).2
|
||
Volunteer glufosinate-resistant crops from the previous year will not be controlled. A timely cultivation 7 to
|
||
|
||
ϵ
|
||
|
||
10 days after an application and/or retreatment 10-21 days after the first application is needed for
|
||
controlling dense clumps of volunteer corn.
|
||
3 May require sequential applications for control.
|
||
4 For best control of yellow foxtail, field sandbur, crabgrass, and wild oats, treat prior to tiller initiation.
|
||
|
||
|
||
Table 3. Biennial and Perennial Weeds Controlled
|
||
(including Glyphosate-, Triazine-, PPO-, ALS-, HPPD-, and Auxin-Resistant Biotypes)
|
||
For control of the biennial and perennial weeds listed below, tank mix partners or sequential
|
||
applications of Cheetah are specified by crop (see crop sections)
|
||
|
||
|
||
Common Name
|
||
|
||
|
||
|
||
Scientific Name
|
||
|
||
29.0 – 43.0 Fl Oz/A 1
|
||
(0.53-0.79 lb ai/A)
|
||
C=Control
|
||
S = Suppression
|
||
Alfalfa Medicago sativa L. C
|
||
Bermudagrass Cynodon dactylon C
|
||
Bindweed, field Convolvulus arvensis L. C
|
||
Bindweed, hedge Calystegia sepium C
|
||
Bluegrass, Kentucky Poa pratensis L. C
|
||
Blueweed, Texas Helianthus ciliaris DC. C
|
||
Bromegrass, smooth Bromus inermis C
|
||
Burdock Arctium spp. C
|
||
Bursage, woollyleaf Ambrosia grayi C
|
||
Chickweed, Mouse-ear Cerastium vulgatum L. C
|
||
Clover, red Trifolium pratense L. C
|
||
Dandelion Taraxacum officinale C
|
||
Dock, smooth Rumex spec. C
|
||
Dogbane, hemp Apocynum cannabinum S
|
||
Goldenrod, gray Solidago nemoralis S
|
||
Johnsongrass, rhizome Sorghum halepense C
|
||
Milkweed, common Asclepias syriaca S
|
||
Milkweed, honeyvine Ampelamus albidus S
|
||
Muhly, wirestem Muhlenbergia frondosa S
|
||
Nightshade, silverleaf Solanum elaeagnifolium C
|
||
Nutsedge, purple Cyperus rotundus S
|
||
Nutsedge, yellow Cyperus esculentus S
|
||
Orchardgrass Dactylis glomerata L. C
|
||
Poinsettia, wild Euphorbia heterophylla L. C
|
||
Pokeweed Phytolaccaceae C
|
||
Quackgrass Agropyron repens S
|
||
Sowthistle, perennial Sonchus arvensis L. C
|
||
Thistle, bull Cirsium vulgare C
|
||
Thistle, Canada Cirsium arvense C
|
||
Timothy Phleum pretense L. S
|
||
Wormwood, biennial Artemisia biennis S
|
||
1 Maximum rate on canola, field corn, sweet corn and soybean in California is 36 fl oz/A (0.66 lb ai/A).
|
||
|
||
APPLICATION AND MIXING PROCEDURES
|
||
Uniform, thorough spray coverage is important to achieve consistent weed control.
|
||
|
||
Ground Application:
|
||
x Refer to the Rate Tables for proper application rates.
|
||
x Apply early, when weeds are small.
|
||
x To avoid drift and insure consistent weed control, apply Cheetah with the spray boom as low as
|
||
possible while maintaining a uniform spray pattern.
|
||
x Apply Cheetah broadcast in a minimum of 15.0 gallons of water per acre. Increase to 20 gallons of
|
||
|
||
ϭϬ
|
||
|
||
water per acre if dense weed canopy exists.
|
||
x Apply at ground speed of less than 15 mph to attain adequate coverage.
|
||
x See the SPRAY DRIFT MANAGEMENT section of this label for additional information on proper
|
||
application of Cheetah.
|
||
|
||
Aerial Application:
|
||
x Refer to the Rate Tables for proper application rates.
|
||
x Apply early, when weeds are small.
|
||
x Apply Cheetah by air in a minimum of 10.0 gallons of water per acre.
|
||
x See the SPRAY DRIFT MANAGEMENT section of this label for additional information on proper
|
||
application of Cheetah.
|
||
|
||
Application and Mixing Restrictions:
|
||
x DO NOT use flood jet nozzles, controlled droplet application equipment, or air-assisted
|
||
spray equipment.
|
||
|
||
Compatibility Testing:
|
||
If Cheetah is to be mixed with pesticide products not listed on this label, test the compatibility of the intended
|
||
tank mixture prior to mixing the products in the spray tank. The following procedure assumes a spray volume
|
||
of 25.0 gallons per acre. For other spray volumes, adjust the amount of the water used accordingly. Check
|
||
compatibility as follows:
|
||
1. Place 1.0 pint of water from the source that will be used to prepare the spray solution in a clear 1.0
|
||
quart jar.
|
||
2. For each pound of a dry tank mix partner to be applied per acre, add 1.5 teaspoons to the jar.
|
||
3. For each 16.0 fluid ounces of a liquid tank mix partner to be applied per acre, add 0.5 teaspoon to the
|
||
jar.
|
||
4. For each 16.0 fluid ounces of Cheetah to be applied per acre, add 0.5 teaspoon to the jar.
|
||
5. After adding all the ingredients, place a lid on the jar and tighten. Invert 10 times to mix.
|
||
6. Let the mixture stand for 15 minutes, and evaluate the solution for uniformity and stability. Look for
|
||
separation, large flakes, precipitates, gels, heavy oily film on the jar, or other signs of incompatibility. If
|
||
the tank mix partners are not compatible, DO NOT use the mixture in a spray tank.
|
||
7. After compatibility testing is complete, dispose of any pesticide wastes in accordance with the
|
||
STORAGE AND DISPOSAL section of this label.
|
||
|
||
MIXING INSTRUCTIONS
|
||
Tank Mix Instructions: Cheetah may be applied in tank mix combinations with labeled rates of other
|
||
products provided these other products are labeled for the timing and method of application for the crop to
|
||
be treated. The tank mix partner must be used in accordance with the label limitations and precautions. No
|
||
label dosage rates may be exceeded. Cheetah cannot be mixed with any product containing a label
|
||
prohibition against such mixing. Refer to the specific crop section for rates and other restrictions.
|
||
It is the pesticide user's responsibility to ensure that all products are registered for the intended use. Read
|
||
and follow the applicable restrictions and limitations and directions for use on all product labels involved in
|
||
tank mixing. Users must follow the most restrictive directions for use and precautionary statements of each
|
||
product in the tank mixture.
|
||
|
||
Cheetah must be applied with properly calibrated and clean equipment. Cheetah is formulated to mix readily
|
||
in water.
|
||
|
||
Prior to adding Cheetah to the spray tank, ensure that the spray tank is thoroughly clean, particularly if an
|
||
herbicide with the potential to injure crops was previously used (see Cleaning Instructions).
|
||
|
||
Mix Cheetah with water to make a finished spray solution as follows:
|
||
1. Properly calibrated and clean equipment
|
||
2. Fill the spray tank half full with water.
|
||
3. Start agitation.
|
||
4. If mixing with a flowable/wettable powder tank mix partner, prepare a slurry of the proper amount of the
|
||
product in a small amount of water. Add the slurry to the spray tank.
|
||
5. Add the appropriate amount of ammonium sulfate (AMS) to the spray tank.
|
||
6. If mixing with a liquid tank mix partner, add the liquid mix partner next.
|
||
7. Complete filling the spray tank with water before adding Cheetah, as foaming may occur.
|
||
8. Add the proper amount of Cheetah and continue agitation.
|
||
|
||
ϭϭ
|
||
|
||
9. If foaming occurs, use a silicone-based antifoam agent.
|
||
|
||
Ensure that all spray system lines including pipes, booms, etc. have the correct concentration of spray
|
||
solution by flushing out the spray system lines before starting the crop application.
|
||
|
||
If tank mix partners specified on this label are added, maintain good agitation at all times until contents of
|
||
the tank are sprayed. If the spray mixture is allowed to settle, thorough agitation is required to resuspend
|
||
the mixture before spraying is resumed. Keep bypass line on or near bottom of tank to minimize foaming.
|
||
Screen size in nozzles or line strainers must be 50 mesh or larger.
|
||
|
||
Cleaning Instructions:
|
||
Before using Cheetah, thoroughly clean bulk storage tank, refillable tank, nurse tanks, spray tank, lines,
|
||
and filter, particularly if a herbicide with the potential to injure crops was previously used. Thoroughly rinse
|
||
equipment using a commercial tank cleaner and as instructed on the prior herbicide label.
|
||
|
||
After using Cheetah, triple rinse the spray equipment and clean with a commercial tank cleaner before
|
||
using the equipment for crops not containing glufosinate-resistant gene. Make sure any rinsate or foam is
|
||
thoroughly removed from spray tank and boom. Rinsate may be disposed following the pesticide disposal
|
||
directions on this label.
|
||
|
||
SPRAY DRIFT MANAGEMENT
|
||
AVOIDING SPRAY DRIFT AT THE APPLICATION SITE IS THE RESPONSIBILITY OF THE
|
||
APPLICATOR.
|
||
• All aerial and ground application equipment must be properly maintained and calibrated using appropriate
|
||
carriers.
|
||
• For all non-aerial applications, wind speed must be measured adjacent to the application site, on the
|
||
upwind side, immediately prior to application.
|
||
|
||
MANDATORY SPRAY DRIFT MITIGATION
|
||
• When applying to crops via aerial application equipment, the spray boom must be mounted on the
|
||
aircraft so as to minimize drift caused by wing tip or rotor blade vortices. The boom length must not
|
||
exceed 75% of the wingspan or 90% of the rotor blade diameter.
|
||
• When applying to crops via aerial application equipment, applicators must use ½ swath displacement
|
||
upwind at the downwind edge of the field.
|
||
• DO NOT apply when wind speeds exceed 10 miles per hour at the application site.
|
||
• DO NOT apply during temperature inversions.
|
||
• For aerial applications, DO NOT release spray at a height greater than 10 ft above the crop canopy,
|
||
unless a greater application height is necessary for pilot safety.
|
||
• For ground applications and aerial applications, select nozzle and pressure that deliver medium to
|
||
coarse spray droplets as indicated in nozzle manufacturer’s catalogues and in accordance with ASABE
|
||
Standard 572.1.
|
||
|
||
• Spray at the appropriate boom height based on nozzle selection and nozzle spacing, but DO NOT
|
||
exceed a boom height of 24 inches above target pest or crop canopy. Set boom to lowest effective height
|
||
over the target pest or crop canopy based on equipment manufacturer’s directions. Automated boom
|
||
height controllers are recommended with large booms to
|
||
better maintain optimum nozzle to canopy
|
||
height. Excessive boom height will increase the potential for spray drift.
|
||
• For non-crop vegetation management ground applications, apply with the nozzle height no more than
|
||
4 feet above the ground or target vegetation, unless necessitated by the application equipment.
|
||
Examples would include roadside, railroad, utility rights of way, forestry and other industrial vegetation
|
||
management applications where safety or natural barriers obstruct application.
|
||
|
||
|
||
SPRAY DRIFT ADVISORIES
|
||
The interaction of many equipment and weather-related factors determines the potential for spray drift. The
|
||
applicator is responsible for considering all these factors when making application decisions.
|
||
|
||
POLLINATOR ADVISORY
|
||
This product contains an herbicide. Follow all label directions and precautions to minimize potential off-
|
||
|
||
ϭϮ
|
||
|
||
target exposure in order to prevent effects to non-target plants adjacent to the treated site which may serve
|
||
as habitat or forage for pollinators.
|
||
|
||
IMPORTANCE OF DROPLET SIZE
|
||
The most effective way to reduce drift potential is to apply large droplets. The best drift management
|
||
strategy is to apply the largest droplets that provide sufficient coverage and control. The presence of
|
||
sensitive species nearby, the environmental conditions, and pest pressure may affect how an applicator
|
||
balances drift control and coverage. APPLYING LARGER DROPLETS REDUCES DRIFT POTENTIAL,
|
||
BUT WILL NOT PREVENT DRIFT IF APPLICATIONS ARE MADE IMPROPERLY OR UNDER
|
||
UNFAVORABLE ENVIRONMENTAL CONDITIONS! See Wind, Temperature and Humidity, and
|
||
Temperature Inversions sections of this label.
|
||
|
||
Controlling Droplet Size – Ground Boom
|
||
• Volume - Use high flow rate nozzles to apply the highest practical spray volume. Nozzles with higher rated
|
||
flows produce larger droplets.
|
||
• Pressure - Use the lower spray pressures recommended for the nozzle. Higher pressure reduces droplet
|
||
size and does not improve canopy penetration. WHEN HIGHER FLOW RATES ARE NEEDED, USE A
|
||
HIGHER-CAPACITY NOZZLE INSTEAD OF INCREASING PRESSURE.
|
||
• Nozzle Type - Use a nozzle type that is designed for the intended application. With most nozzle types,
|
||
narrower spray angles produce larger droplets. Consider using low-drift nozzles.
|
||
|
||
Controlling Droplet Size – Aircraft
|
||
• Number of Nozzles - Use the minimum number of nozzles with the highest flow rate that provide uniform
|
||
coverage.
|
||
• Nozzle Orientation - Orienting nozzles so that the spray is emitted backwards, parallel to the airstream
|
||
will produce larger droplets than other orientations. AVOIDING SPRAY DRIFT IS THE RESPONSIBILITY
|
||
OF THE APPLICATOR.
|
||
• Nozzle Type - Solid stream nozzles (including disc and core with swirl plate removed) oriented straight
|
||
back produce larger droplets than other nozzle types.
|
||
• Boom Length - Longer booms increase drift potential. Therefore a shorter boom length is recommended.
|
||
• Application Height - Application more than 10 ft. above the canopy increases the potential for spray drift.
|
||
|
||
BOOM HEIGHT
|
||
Setting the boom at the lowest referenced height (if specified) which provides uniform coverage reduces
|
||
the exposure of droplets to evaporation and wind. For ground equipment, the boom should remain level
|
||
with the crop and have minimal bounce.
|
||
|
||
Drift Reduction Technology (DRT)
|
||
The EPA Drift Reduction Technology (DRT) Program was developed to encourage the manufacturer,
|
||
marketing, and use of spray technologies scientifically verified to significantly reduce pesticide drift. The
|
||
use of DRTs should result in significantly less pesticide from spray applications drifting and being
|
||
deposited in areas not targeted by those applications, compared to spray technologies that DO NOT meet
|
||
the minimum DRT standard. EPA-verified drift reduction technologies (DRTs) and their ratings will be
|
||
added to the following webpage when they become available: https://www.epa.gov/reducing-pesticide-
|
||
drift/epa-verified-and-rated-drift-reduction-technologies
|
||
|
||
WIND
|
||
Drift potential increases at wind speeds of less than 3 mph (due to inversion potential) or more than 10
|
||
mph. However, many factors, including droplet size and equipment type determine drift potential at any
|
||
given wind speed. AVOID APPLICATIONS DURING GUSTY OR WINDLESS CONDITIONS.
|
||
Note: Local terrain can influence wind patterns. Every applicator needs to be familiar be familiar with local
|
||
wind patterns and how they affect spray drift.
|
||
|
||
TEMPERATURE AND HUMIDITY
|
||
When making applications in hot and dry conditions, set up equipment to produce larger droplets to reduce
|
||
effects of evaporation.
|
||
|
||
TEMPERATURE INVERSIONS
|
||
|
||
ϭϯ
|
||
|
||
Drift potential is high during a temperature inversion. Temperature inversions restrict vertical air mixing,
|
||
which causes small suspended droplets to remain close to the ground and move laterally in a concentrated
|
||
cloud. Temperature inversions are characterized by increasing temperature with altitude and are common
|
||
on nights with limited cloud cover and light to no wind. They begin to form as the sun sets and often continue
|
||
into the morning. Their presence can be indicated by ground fog; however, if fog is not present, inversions
|
||
can also be identified by the movement of smoke from a ground source or an aircraft smoke generator.
|
||
Smoke that layers and moves laterally in a concentrated cloud (under low wind conditions) indicates an
|
||
inversion, while smoke that moves upward and rapidly dissipates indicates good vertical air mixing.
|
||
|
||
SHIELDED SPRAYERS
|
||
Shielding the boom or individual nozzles can reduce the effects of wind. However, it is the responsibility of
|
||
the applicator to verify that the shields are preventing drift and not interfering with uniform deposition of the
|
||
product.
|
||
|
||
APPLICATION DIRECTIONS FOR BURNDOWN USE
|
||
Cheetah may be applied as a burndown treatment prior to planting or prior to emergence of any variety
|
||
of canola (including camelina), corn, sweet corn, cotton, soybean or sugar beet.
|
||
|
||
Application Timing:
|
||
Apply to small and actively growing weeds, targeting less than 3 inch weeds in height. For additional
|
||
information on weed heights refer to the WEED CONTROL FOR ROW CROPS section. Warm
|
||
temperatures, high humidity, and bright sunlight improve the performance of Cheetah. Weed control may
|
||
be reduced when applications are made to weeds under stress due to drought or cool temperatures.
|
||
For optimum results on lambsquarters, Palmer amaranth and velvetleaf make applications between dawn
|
||
and 2 hours before sunset.
|
||
Cheetah is rainfast 4 hours after application, therefore, rainfall within 4 hours may necessitate retreatment.
|
||
|
||
Application Rates:
|
||
Apply 29.0 – 43.0 fluid ounces (1.32 lbs ai/A 0.53-0.79 lbs ai/A) per acre of Cheetah depending on crop,
|
||
weed species and intention of post application use. Please see application charts below.
|
||
|
||
Restrictions (also see specific crop use directions):
|
||
• In cotton, if environmental conditions prevent timely applications, a single application may be made of up
|
||
to 43.0 fluid ounces (0.79 lbs ai/A) per acre of Cheetah. If more than 29.0 fluid ounces (0.53 lbs ai/A)
|
||
per acre are used in any single application, the annual total may not exceed 72.0 fluid ounces (1.32
|
||
lbs ai/A) per acre, including all application timings.
|
||
|
||
• In canola (including camelina), corn (sweet and field) and soybean , if environmental conditions
|
||
prevent timely applications, a single application may be made of up to 43.0* fluid ounces(0.79 lbs ai/A) per
|
||
acre of Cheetah. The year total may not exceed 43.0* fluid ounces (0.79 lbs ai/A) per acre, including all
|
||
application timings, for non-Glufosinate resistant crops. *Maximum rate in California is 36 fl oz/A (0.66 lb
|
||
ai/A).
|
||
|
||
• [In sugar beets, if environmental conditions prevent timely applications, a single application may be made
|
||
of up to 36.0 fluid ounces (0.66 lbs ai/A) per acre of Cheetah. No additional applications of Cheetah may
|
||
be made post emergence to the crop during the year.]
|
||
|
||
|
||
Adjuvant:
|
||
Ammonium sulfate (AMS) may be used at 1.5 to 3 pounds per acre. Adjuvant rates are dependent on tank
|
||
mix partners, temperatures, environmental conditions and potential for leaf burn.
|
||
AMS has shown to improve weed control of difficult-to-control weeds, like lambsquarters and velvetleaf,
|
||
under difficult environmental conditions (low relative humidity) or hard water.
|
||
|
||
Surfactants / Crop Oils:
|
||
The use of surfactants may be included. Please refer to the surfactant label for more detailed information.
|
||
|
||
ϭϰ
|
||
|
||
Table 4. APPLICATION DIRECTIONS FOR NON-GLUFOSINATE RESISTANT CROPS
|
||
|
||
Crop Burndown In Season Applications Annual Max
|
||
Canola, Soybean, Sweet
|
||
Corn, Field Corn
|
||
29 – 43* fl oz/A
|
||
(0.53 – 0.79 lbs ai/A) None 43* fl oz/A
|
||
(0.79 lbs ai/A)
|
||
Sugar beets 29 - 36 fl oz/A
|
||
(0.53 – 0.66 lbs ai/A) None 36 fl oz/A
|
||
(0.66 lbs ai/A)
|
||
Cotton Use Pattern 1 29 fl oz/A
|
||
(0.53 lbs ai/A)
|
||
2 applications at 29 fl oz/A**
|
||
(0.53 lbs ai/A)Make second
|
||
application 10-14 days after the
|
||
first application.
|
||
87 fl oz/A
|
||
(1.59 lbs ai/A)
|
||
Cotton Use Pattern 2 30-43 fl oz/A
|
||
(0.55 – 0.79 lbs ai/A)
|
||
1 application at 29 fl oz/A**
|
||
(0.53 lbs ai/A)
|
||
72 fl oz/A
|
||
(1.32 lbs ai/A)
|
||
* Maximum rate in California is 36 fl oz/A (0.66 lbs ai/A).
|
||
** Cotton containing the glufosinate-resistant gene OR with hooded sprayer for all varieties (see COTTON
|
||
use directions).
|
||
|
||
|
||
Table 5. APPLICATION DIRECTIONS FOR CROPS CONTAINING THE GLUFOSINATE RESISTANT
|
||
GENE TRAIT
|
||
|
||
GLUFOSINATE
|
||
RESISTANT Crop Burndown
|
||
In Season Applications
|
||
of Crops Containing the
|
||
GLUFOSINATE RESISTANT GENE
|
||
Annual Max
|
||
Soybean 29 – 43* fl oz/A
|
||
(0.53 – 0.79 lbs ai/A)
|
||
1 to 2 applications at 29 – 43* fl oz/A
|
||
(0.53 – 0.79 lbs ai/A)For soybeans,
|
||
make second application
|
||
at least 5 days after the first application.
|
||
|
||
87* fl oz/A
|
||
(1.59 lbs ai/A)
|
||
Field Corn 29 – 43** fl oz/A
|
||
(0.53 – 0.79 lbs ai/A)
|
||
1 to 2 applications at 29 – 43** fl oz/A
|
||
(0.53 – 0.79 lbs ai/A)Make second
|
||
application at least 7 10 days after the
|
||
first application.
|
||
87** fl oz/A
|
||
(1.59 lbs ai/A)
|
||
Sweet Corn*** 22 fl oz/A
|
||
(0.40 lbs ai/A)
|
||
1 to 2 applications at 22 fl oz/A
|
||
(0.4 lbs ai/A)Make second application at
|
||
least 7 days after the first application.
|
||
44 fl oz/A
|
||
(0.8 lbs ai/A)
|
||
Canola/Camelina 29 – 43* fl oz/A
|
||
(0.53 – 0.79 lbs ai/A)
|
||
1 to 2 applications at 29 fl oz/A
|
||
(0.53 lbs ai/A)Make second application
|
||
at least 10 days after the first application
|
||
87* fl oz/A
|
||
(1.59 lbs ai/A)
|
||
Cotton Use
|
||
Pattern 1
|
||
29 fl oz/A
|
||
(0.53 lbs ai/A)
|
||
1 to 2 applications at 29 fl oz/A****
|
||
(0.53 lbs ai/A)Make second application
|
||
10-14 days after the first application.
|
||
87 fl oz/A
|
||
(1.59 lbs ai/A)
|
||
|
||
ϭϱ
|
||
|
||
* Maximum rate in California is 36 fl oz/A (0.66 lbs ai/A) with annual maximum of 72 fl oz/A (1.32 lbs ai/A).
|
||
** Maximum rate in California is 22 fl oz/A (0.40 lbs ai/A) with annual maximum of 44 fl oz/A (0.8 lbs ai/A).
|
||
*** Not for use in California
|
||
**** Cotton containing the glufosinate-resistant gene OR with hooded sprayer for all varieties (see
|
||
COTTON use directions).
|
||
|
||
APPLICATION DIRECTIONS FOR USE ON SUGAR BEETS CONTAINING THE
|
||
GLUFOSINATE-RESISTANT GENE
|
||
[Not for use in California.]
|
||
Apply Cheetah only to sugar beets containing the glufosinate-resistant gene. Cheetah is a contact
|
||
herbicide and requires uniform, thorough spray coverage to achieve optimum weed control.
|
||
|
||
Application Timing:
|
||
Apply to small and actively growing weeds, targeting less than 3 inch weeds in height. For additional
|
||
information on weed heights refer to the WEED CONTROL FOR ROW CROPS section.
|
||
Weed control may be reduced if application is made when heavy dew, fog, and mist/rain are present; or
|
||
when weeds are under stress due to drought, cool temperatures, or extended periods of cloudiness.
|
||
Applications of Cheetah on sugar beets containing the glufosinate-resistant gene may be made from the
|
||
cotyledon stage up to the 10-Ieaf stage of the sugar beet. Cheetah is a foliar-active material with little or no
|
||
soil-residual activity.
|
||
Cheetah is rainfast 4 hours after application, therefore, rainfall within 4 hours may necessitate retreatment.
|
||
For best result:
|
||
x On lambsquarters, Palmer amaranth and velvetleaf control, make applications of Cheetah
|
||
between dawn and 2 hours before sunset.
|
||
x Warm temperatures, high humidity, and bright sunlight improve the performance of Cheetah.
|
||
|
||
Application Rates:
|
||
Apply 29 - 36 fl oz/A (0.53 – 0.66 lbs ai/A) depending on weed species, size and density per weed chart.
|
||
If a second application is needed, make the second application in a minimum of 10 days after the first
|
||
application.
|
||
The maximum annual rate of Cheetah on sugar beets is 60.0 fl oz/A (1.1 lbs ai/A).
|
||
Use a minimum spray volume of 15 gallons per acre, unless there is a difficult to control situation
|
||
(including dense canopy, large weeds or unfavorable growing conditions are present). In difficult to
|
||
control situations use a minimum spray volume of 20 gallons per acre.
|
||
|
||
Adjuvants:
|
||
Ammonium sulfate (AMS) may be used at 1.5 to 3.0 pounds per acre. Adjuvant rates are dependent on a
|
||
variety of factors including tank mix partners, environmental conditions (including temperature) and
|
||
potential for leaf burn.
|
||
AMS has shown to improve weed control of difficult-to-control weeds, like lambsquarters and velvetleaf,
|
||
under difficult environmental conditions (including low relative humidity) or hard water.
|
||
The use of an anti-foam agent is advised.
|
||
|
||
Surfactants / Oils:
|
||
The use of additional surfactants or crop oils in tank mixes with Cheetah may increase the risk of crop
|
||
response. Please refer to the surfactant label for more detailed information.
|
||
|
||
|
||
Restrictions to the Directions For Use on Sugar Beets Containing the Glufosinate-Resistant Gene:
|
||
x DO NOT apply more than 60.0 fl oz/A (1.1 lbs ai/A) of Cheetah per year.
|
||
x DO NOT apply Cheetah within 60 days of harvesting sugar beets.
|
||
x If a second application is needed, make the second application a minimum of 10 days after the
|
||
first application.
|
||
Cotton Use
|
||
Pattern 2
|
||
|
||
30 - 43 fl oz/A
|
||
(0.55 – 0.79 lbs ai/A)
|
||
1 application at 29 fl oz/A****
|
||
(0.53 lbs ai/A)
|
||
72 fl oz/A
|
||
(1.32 lbs ai/A)
|
||
Sugar beets 29 - 36 fl oz/A
|
||
(0.53 – 0.66 lbs ai/A)
|
||
1 application at 29 fl oz/A
|
||
(0.53 lbs ai/A)
|
||
60 fl oz/A
|
||
(1.1 lbs ai/A)
|
||
|
||
ϭϲ
|
||
|
||
x DO NOT exceed the single application rate maximum of 36 fl oz/A (0.66 lb ai/A).
|
||
x DO NOT make more than 2 applications per year.
|
||
x DO NOT plant rotation crops in a field treated with Cheetah within 120 days after the last
|
||
application of Cheetah with the exception of wheat, barley, buckwheat, millet, oats, rye, sorghum,
|
||
and triticale which may be planted 70 days after the last application of Cheetah. Corn, soybeans,
|
||
canola, and sugar beets resistant to the active ingredient of Cheetah may be planted at any time.
|
||
x DO NOT graze the treated crop or cut for hay.
|
||
x DO NOT apply Cheetah if sugar beets show injury from prior herbicide applications or
|
||
environmental stress (drought, excessive rainfall, etc.).
|
||
x DO NOT apply Cheetah through any type of irrigation system.
|
||
|
||
|
||
APPLICATION DIRECTIONS FOR USE ON CAMELINA (GOLD-OF-PLEASURE)
|
||
CONTAINING THE GLUFOSINATE-RESISTANT GENE
|
||
Apply Cheetah only to camelina containing the Glufosinate-resistant gene. Uniform, thorough spray
|
||
coverage is necessary to achieve consistent weed control.
|
||
|
||
Application Timing:
|
||
Apply to small and actively growing weeds, targeting less than 3 inch weeds in height. For additional
|
||
information on weed heights refer to the WEED CONTROL FOR ROW CROPS section.
|
||
Weed control may be reduced if application is made when heavy dew, fog, and mist/rain are present; or
|
||
when weeds are under stress due to drought, cool temperatures, or extended periods of cloudiness.
|
||
Applications of Cheetah on camelina containing the glufosinate-resistant gene may be made from the
|
||
cotyledon stage up to the early bolt stage of the camelina. Slight discoloration of the camelina may be
|
||
visible after application. This effect is temporary and will not influence crop growth, maturity, or yield.
|
||
Cheetah is a foliar-active material with little or no soil-residual activity.
|
||
Cheetah is rainfast 4 hours after application, therefore, rainfall within 4 hours may necessitate retreatment.
|
||
For best result:
|
||
x On lambsquarters, Palmer amaranth and velvet leaf control, make applications of Cheetah between
|
||
dawn and 2 hours before sunset.
|
||
x Warm temperatures, high humidity, and bright sunlight improve the performance of Cheetah.
|
||
|
||
Application Rates:
|
||
Apply Cheetah at 22.0 to 29.0 fl oz/A (0.4 to 0.53 lbs ai/A) per application, depending on weed species,
|
||
size and density per weed chart.
|
||
If a second application is needed, make the second application in a minimum of 7 10 days after the first
|
||
application.
|
||
The maximum annual rate of Cheetah on camelina is 87.0 fl oz/A (1.59 lbs ai/A).
|
||
|
||
Use a minimum spray volume of 15 gallons per acre, unless there is a difficult to control situation
|
||
(including dense canopy, large weeds or unfavorable growing conditions are present). In difficult to
|
||
control situations use a minimum spray volume of 20 gallons per acre.
|
||
|
||
Application Rates with Tank Mix Partners:
|
||
It is the pesticide user’s responsibility to ensure that all products are registered for the intended use. Read
|
||
and follow the applicable restrictions and limitations and directions for use on all product labels involved in
|
||
tank mixing. Users must follow the most restrictive directions for use and precautionary statements of each
|
||
product in the tank mixture.
|
||
Apply Cheetah at 22.0 to 29.0 fl oz/A (0.4 to 0.53 lbs ai/A) per application, depending on weed species,
|
||
size and density per weed chart.
|
||
Tank mix partners advised to enhance grass control, including [quizalofop p-ethyl][,] [sethoydim][,] [and]
|
||
[clethodim].
|
||
If a second application is needed, make the second application in a minimum of 7 10 days after the first
|
||
application.
|
||
Tank mixes may aid in the performance of Cheetah. Please refer to weed chart tables for a listing of weed
|
||
species controlled at this rate.
|
||
No additional surfactant is needed with any tank mix partner.
|
||
The tank mix partner must be used in accordance with the label limitations, restrictions and precautions.
|
||
|
||
ϭϳ
|
||
|
||
DO NOT exceed any labeled dosage rates.
|
||
DO NOT mix Cheetah mix with any product containing a label prohibition against such mixing.
|
||
|
||
Adjuvants:
|
||
Ammonium sulfate (AMS) may be used at 1.5 to 3.0 pounds per acre. Adjuvant rates are dependent on a
|
||
variety of factors including tank mix partners, environmental conditions (including temperature) and
|
||
potential for leaf burn.
|
||
AMS has shown to improve weed control of difficult-to-control weeds, like lambsquarters and velvetleaf,
|
||
under difficult environmental conditions (including low relative humidity) or hard water.
|
||
The use of an anti-foam agent is advised.
|
||
|
||
Surfactants / Oils:
|
||
The use of additional surfactants or crop oils in tank mixes with Cheetah may increase the risk of crop
|
||
response. Please refer to the surfactant label for more detailed information.
|
||
|
||
Restrictions to the Directions For Use on Camelina Containing the Glufosinate-Resistant Gene:
|
||
• DO NOT exceed the maximum single application rate of 43 fl oz/A (0.79 lb ai/A).
|
||
• DO NOT apply more than 87.0 fl oz/A (1.59 lbs ai/A) of Cheetah per year.
|
||
|
||
• DO NOT use on camelina containing the glufosinate-resistant gene in the states of Alabama, Delaware,
|
||
Georgia, Kentucky, Maryland, New Jersey, North Carolina, South Carolina, Tennessee, Virginia and
|
||
West Virginia.
|
||
• DO NOT apply more than 2 applications of Cheetah per year. Sequential applications must be at least
|
||
10 days apart.
|
||
• DO NOT apply Cheetah within 65 days of harvesting camelina.
|
||
• DO NOT graze the treated crop or cut for hay.
|
||
• DO NOT apply Cheetah if camelina shows injury from prior herbicide applications or environmental
|
||
stress (drought, excessive rainfall, etc.).
|
||
• DO NOT apply Cheetah through any type of irrigation system.
|
||
• Refer to the ROTATIONAL CROP RESTRICTIONS section under the PRODUCT INFORMATION
|
||
heading of this label for the appropriate rotational crop plant back intervals.
|
||
|
||
|
||
|
||
|
||
APPLICATION DIRECTIONS FOR USE ON CANOLA CONTAINING THE
|
||
GLUFOSINATE-RESISTANT GENE
|
||
Apply Cheetah only to canola containing the Glufosinate-resistant gene. Uniform, thorough spray
|
||
coverage is necessary to achieve consistent weed control.
|
||
|
||
Application Timing:
|
||
Apply to small and actively growing weeds, targeting less than 3 inch weeds in height. For additional
|
||
information on weed heights refer to the WEED CONTROL FOR ROW CROPS section.
|
||
Weed control may be reduced if application is made when heavy dew, fog, and mist/rain are present; or
|
||
when weeds are under stress due to drought, cool temperatures, or extended periods of cloudiness.
|
||
Applications of Cheetah on canola containing the glufosinate-resistant gene may be made from the
|
||
cotyledon stage up to the early bolt stage of the canola. Slight discoloration of the canola may be visible
|
||
after application. This effect is temporary and will not influence crop growth, maturity, or yield.
|
||
Cheetah is a foliar-active material with little or no soil-residual activity.
|
||
Cheetah is rainfast 4 hours after application, therefore, rainfall within 4 hours may necessitate retreatment.
|
||
For best result:
|
||
x On lambsquarters, Palmer amaranth and velvetleaf control, make applications of Cheetah between
|
||
dawn and 2 hours before sunset.
|
||
x Warm temperatures, high humidity, and bright sunlight improve the performance of Cheetah.
|
||
|
||
Application Rates:
|
||
Apply Cheetah at 22.0 to 29.0 fl oz/A (0.4 to 0.53 lbs ai/A) per application, depending on weed species,
|
||
size and density per weed chart.
|
||
If a second application is needed, make the second application in a minimum of 7 10 days after the first
|
||
|
||
ϭϴ
|
||
|
||
application.
|
||
The maximum annual rate of Cheetah on canola is 87.0 fl oz/A (1.59 lbs ai/A).
|
||
Use a minimum spray volume of 15 gallons per acre, unless there is a difficult to control situation
|
||
(including dense canopy, large weeds or unfavorable growing conditions are present). In difficult to
|
||
control situations use a minimum spray volume of 20 gallons per acre.
|
||
|
||
Application Rates with Tank Mix Partners:
|
||
It is the pesticide user’s responsibility to ensure that all products are registered for the intended use. Read
|
||
and follow the applicable restrictions and limitations and directions for use on all product labels involved in
|
||
tank mixing. Users must follow the most restrictive directions for use and precautionary statements of each
|
||
product in the tank mixture.
|
||
Apply Cheetah at 22.0 to 29.0 fl oz/A (0.4 to 0.53 lbs ai/A) per application, depending on weed species,
|
||
size and density per weed chart.
|
||
Tank mix partners advised to enhance grass control, including [quizalofop p-ethyl][,] [sethoydim][,] [and]
|
||
[clethodim].
|
||
If a second application is needed, make the second application in a minimum of 7 10 days after the first
|
||
application.
|
||
Tank mixes may aid in the performance of Cheetah. Please refer to weed chart tables for a listing of weed
|
||
species controlled at this rate.
|
||
No additional surfactant is needed with any tank mix partner.
|
||
The tank mix partner must be used in accordance with the label limitations, restrictions and precautions.
|
||
DO NOT exceed any labeled dosage rates.
|
||
DO NOT mix Cheetah mix with any product containing a label prohibition against such mixing.
|
||
|
||
Adjuvants:
|
||
Ammonium sulfate (AMS) may be used at 1.5 to 3.0 pounds per acre. Adjuvant rates are dependent on a
|
||
variety of factors including tank mix partners, environmental conditions (including temperature) and
|
||
potential for leaf burn.
|
||
AMS has shown to improve weed control of difficult-to-control weeds, like lambsquarters and velvetleaf,
|
||
under difficult environmental conditions (including low relative humidity) or hard water.
|
||
The use of an anti-foam agent is advised.
|
||
|
||
Surfactants / Oils:
|
||
The use of additional surfactants or crop oils in tank mixes with Cheetah may increase the risk of crop
|
||
response. Please refer to the surfactant label for more detailed information.
|
||
|
||
Restrictions to the Directions For Use on Canola Containing the Glufosinate-Resistant Gene:
|
||
• DO NOT exceed the maximum single application rate of 43 fl oz/A (0.79 lb ai/A).
|
||
• DO NOT apply more than 87.0 fl oz/A (1.59 lbs ai/A) of Cheetah per year.
|
||
|
||
• DO NOT use on canola containing the glufosinate-resistant gene in the states of Alabama, Delaware,
|
||
Georgia, Kentucky, Maryland, New Jersey, North Carolina, South Carolina, Tennessee, Virginia and
|
||
West Virginia.
|
||
• DO NOT apply more than 2 applications of Cheetah per year. Sequential applications must be at least
|
||
10 days apart.
|
||
• DO NOT apply Cheetah within 65 days of harvesting canola.
|
||
• DO NOT graze the treated crop or cut for hay.
|
||
• DO NOT apply Cheetah if canola shows injury from prior herbicide applications or environmental stress
|
||
(drought, excessive rainfall, etc.).
|
||
• DO NOT apply Cheetah through any type of irrigation system.
|
||
• Refer to the ROTATIONAL CROP RESTRICTIONS section under the PRODUCT INFORMATION
|
||
heading of this label for the appropriate rotational crop plant back intervals.
|
||
|
||
|
||
APPLICATION RATE AND TIMING FOR CANOLA CONTAINING GLUFOSINATE
|
||
RESISTANT GENE SEED PROPAGATION
|
||
[Not for use in California]
|
||
Up to 3 applications of Cheetah at up to 29.0 fl oz/A (0.53 lbs ai/A) per application may be made to canola
|
||
containing the Glufosinate-resistant gene for seed propagation. Applications may be made from the
|
||
|
||
ϭϵ
|
||
|
||
cotyledon stage up to the early bolting stage (e.g., BBCH 18-30, between just prior to stem
|
||
elongation/bolting, 8 or more leaves and beginning of stem elongation, no internodes).
|
||
|
||
Restrictions to the Directions for Canola Containing the glufosinate-resistant gene for Seed
|
||
Propagation:
|
||
• Maximum single application is 29.0 fl oz/A (0.53 lbs ai/A).
|
||
• DO NOT apply more than 3 applications.
|
||
• Sequential applications must be made more than 10 days apart.
|
||
• DO NOT apply more than 87.0 fl oz/A (1.59 lbs ai/A) of Cheetah per year.
|
||
• DO NOT apply Cheetah beyond the early bolting stage or within 65 days of harvesting canola seed.
|
||
• DO NOT use treated canola seed for food, feed or oil purposes.
|
||
• DO NOT apply Cheetah if canola shows injury from prior herbicide applications or environmental stress
|
||
(drought, excessive rainfall, etc.).
|
||
• DO NOT apply this product through any type of irrigation system.
|
||
|
||
APPLICATION DIRECTIONS FOR USE ON SWEET CORN CONTAINING THE
|
||
GLUFOSINATE RESISTANT GENE
|
||
[Not for use in California.]
|
||
Apply Cheetah only to sweet corn containing the glufosinate-resistant gene. Uniform, thorough spray
|
||
coverage is necessary to achieve consistent weed control.
|
||
|
||
Application Timing:
|
||
Apply to small and actively growing weeds, targeting less than 3 inch weeds in height. For additional
|
||
information on weed heights refer to the WEED CONTROL FOR ROW CROPS section.
|
||
Weed control may be reduced if application is made when heavy dew, fog, and mist/rain are present; or
|
||
when weeds are under stress due to drought, cool temperatures, or extended periods of cloudiness.
|
||
Applications for Cheetah on sweet corn may be made from emergence until the V-6 stage of growth.
|
||
Cheetah is a foliar-active material with little or no soil-residual activity.
|
||
Cheetah is rainfast 4 hours after application, therefore, rainfall within 4 hours may necessitate retreatment.
|
||
For best result:
|
||
x On lambsquarters, Palmer amaranth and velvetleaf control, make applications of Cheetah between
|
||
dawn and 2 hours before sunset.
|
||
x Warm temperatures, high humidity, and bright sunlight improve the performance of Cheetah.
|
||
|
||
Application Rate:
|
||
Apply Cheetah at 22.0 fl oz/A (0.4 lbs ai/A), depending on weed species, size and density per weed chart.
|
||
If a second application is needed, make the second application in a minimum of 7 days after the first
|
||
application.
|
||
The maximum annual rate of Cheetah on sweet corn is 44.0 fl oz/A (0.8 lbs ai/A).
|
||
Use a minimum spray volume of 15 gallons per acre, unless there is a difficult to control situation
|
||
(including dense canopy, large weeds or unfavorable growing conditions are present). In difficult to
|
||
control situations use a minimum spray volume of 20 gallons per acre.
|
||
|
||
Application Rates with Tank Mix Partners:
|
||
It is the pesticide user’s responsibility to ensure that all products are registered for the intended use. Read
|
||
and follow the applicable restrictions and limitations and directions for use on all product labels involved in
|
||
tank mixing. Users must follow the most restrictive directions for use and precautionary statements of each
|
||
product in the tank mixture.
|
||
Apply Cheetah at 22.0 fl oz/A (0.4 lbs ai/A) per application, depending on weed species, size and density
|
||
per weed chart.
|
||
Advised tank mix partners, including [atrazine][,] [tembotrione][,] [thiencarbazone-methyl][,][and]
|
||
[dicamba, DGA salt].
|
||
If a second application is needed, make the second application in a minimum of 7 days after the first
|
||
application.
|
||
Tank mixes may aid in the performance of Cheetah. Please refer to weed chart tables for a listing of weed
|
||
species controlled at this rate.
|
||
No additional surfactant is needed with any tank mix partner.
|
||
|
||
ϮϬ
|
||
|
||
The tank mix partner must be used in accordance with the label limitations, restrictions and precautions.
|
||
DO NOT exceed any labeled dosage rates.
|
||
DO NOT mix Cheetah mix with any product containing a label prohibition against such mixing.
|
||
|
||
Adjuvants:
|
||
Ammonium sulfate (AMS) may be used at 1.5 to 3.0 pounds per acre. Adjuvant rates are dependent on a
|
||
variety of factors including tank mix partners, environmental conditions (including temperature) and
|
||
potential for leaf burn.
|
||
AMS has shown to improve weed control of difficult-to-control weeds, like lambsquarters and velvetleaf,
|
||
under difficult environmental conditions (including low relative humidity) or hard water.
|
||
The use of an anti-foam agent is advised.
|
||
|
||
Surfactants / Oils:
|
||
The use of additional surfactants or crop oils in tank mixes with Cheetah may increase the risk of crop
|
||
response. Please refer to the surfactant label for more detailed information.
|
||
|
||
|
||
Restrictions to the Directions For Use on Sweet Corn Containing the Glufosinate-Resistant Gene:
|
||
x DO NOT apply Cheetah within 50 days of harvesting sweet corn ears and within 55 days of
|
||
harvesting stover.
|
||
x DO NOT apply more than 44.0 fl oz/A (0.8 lbs ai/A) of Cheetah on sweet corn per year.
|
||
x DO NOT apply more than 2 applications of Cheetah to sweet corn per year. Sequential applications
|
||
must be at least 7 days apart.
|
||
x DO NOT exceed the maximum single application rate of 22 fl oz/A (0.40 lb ai/A).
|
||
x If Cheetah was used in a burndown application, no post emergence applications may be applied to
|
||
the crop.
|
||
x DO NOT use nitrogen solutions as spray carriers.
|
||
x DO NOT apply Cheetah if corn shows injury from prior herbicide applications or environmental
|
||
stress (drought, excessive rainfall, etc.)
|
||
x DO NOT apply Cheetah through any type of irrigation system.
|
||
|
||
Refer to the ROTATIONAL CROP RESTRICTIONS section under the PRODUCT INFORMATION heading
|
||
of this label for the appropriate rotational crop plant back intervals.
|
||
|
||
See APPLICATION DIRECTIONS FOR USE ON FIELD CORN AND SILAGE CORN for APPLICATION
|
||
METHODS, MIXING INSTRUCTIONS, and WEED CONTROL TABLES.
|
||
|
||
APPLICATION DIRECTIONS FOR USE ON FIELD CORN AND SILAGE CORN
|
||
CONTAINING THE GLUFOSINATE RESISTANT GENE
|
||
Apply Cheetah only to corn containing the glufosinate-resistant gene. Uniform, thorough spray coverage is
|
||
necessary to achieve consistent weed control.
|
||
|
||
Application Timing:
|
||
Apply to small and actively growing weeds, targeting less than 3 inch weeds in height. For additional
|
||
information on weed heights refer to the WEED CONTROL FOR ROW CROPS section.
|
||
Weed control may be reduced if application is made when heavy dew, fog, and mist/rain are present; or
|
||
when weeds are under stress due to drought, cool temperatures, or extended periods of cloudiness.
|
||
Applications for Cheetah on corn may be made from emergence until the V-6 stage of growth.
|
||
Cheetah is a foliar-active material with little or no soil-residual activity.
|
||
Cheetah is rainfast 4 hours after application, therefore, rainfall within 4 hours may necessitate retreatment.
|
||
For best result:
|
||
x On lambsquarters, Palmer amaranth and velvetleaf control, make applications of Cheetah between
|
||
dawn and 2 hours before sunset.
|
||
x Warm temperatures, high humidity, and bright sunlight improve the performance of Cheetah.
|
||
|
||
Application Rate:
|
||
Apply Cheetah at 29 – 43* fl oz/A (0.53 – 0.79 lbs ai/A), depending on weed species, size and density per
|
||
|
||
Ϯϭ
|
||
|
||
weed chart. *Maximum rate in California is 22 fl oz/A (0.4 lb ai/A).
|
||
If a second application is needed, make the second application at up to 29 fl oz/A (0.53 lbs ai/A) with a
|
||
minimum of 7 10 days after the first application. *Maximum rate in California is 22 fl oz/A (0.4 lb ai/A).
|
||
The maximum annual rate of Cheetah on field corn and silage corn is 87.0* fl oz/A (1.59 lbs ai/A).
|
||
*Maximum annual rate in California is 44 fl oz/A (0.8 lbs ai/A)
|
||
Use a minimum spray volume of 15 gallons per acre, unless there is a difficult to control situation
|
||
(including dense canopy, large weeds or unfavorable growing conditions are present). In difficult to
|
||
control situations use a minimum spray volume of 20 gallons per acre.
|
||
|
||
Application Rates with Tank Mix Partners:
|
||
It is the pesticide user’s responsibility to ensure that all products are registered for the intended use. Read
|
||
and follow the applicable restrictions and limitations and directions for use on all product labels involved in
|
||
tank mixing. Users must follow the most restrictive directions for use and precautionary statements of each
|
||
product in the tank mixture.
|
||
|
||
Apply Cheetah at 29.0 – 43.0* fl oz/A (0.53 – 0.79 lbs ai/A), depending on weed species, size and density
|
||
per weed chart. * Maximum rate in California is 22 fl oz/A (0.4 lb ai/A).
|
||
Advised tank mix partners, including [atrazine][,] [tembotrione][,] [thiencarbazone-methyl][,][and]
|
||
[dicamba, DGA salt].
|
||
If a second application is needed, make the second application in a minimum of 7 10 days after the first
|
||
application.
|
||
Tank mixes may aid in the performance of Cheetah. Please refer to weed chart tables for a listing of weed
|
||
species controlled at this rate.
|
||
No additional surfactant is needed with any tank mix partner.
|
||
The tank mix partner must be used in accordance with the label limitations, restrictions and precautions.
|
||
DO NOT exceed any labeled dosage rates.
|
||
DO NOT mix Cheetah mix with any product containing a label prohibition against such mixing.
|
||
|
||
Adjuvants:
|
||
Ammonium sulfate (AMS) may be used at 1.5 to 3.0 pounds per acre. Adjuvant rates are dependent on a
|
||
variety of factors including tank mix partners, environmental conditions (including temperature) and
|
||
potential for leaf burn.
|
||
AMS has shown to improve weed control of difficult-to-control weeds, like lambsquarters and velvetleaf,
|
||
under difficult environmental conditions (including low relative humidity) or hard water.
|
||
The use of an anti-foam agent is advised.
|
||
|
||
Surfactants / Oils:
|
||
The use of additional surfactants or crop oils in tank mixes with Cheetah may increase the risk of crop
|
||
response. Please refer to the surfactant label for more detailed information.
|
||
|
||
Restrictions to the Directions For Use on Field Corn and Corn Silage Containing the Glufosinate-
|
||
Resistant Gene:
|
||
• DO NOT apply Cheetah within 60 days of harvesting corn forage and within 70 days of harvesting corn
|
||
grain and corn fodder.
|
||
• DO NOT apply more than 2 applications per year. Sequential applications must be at least 10 days
|
||
apart.
|
||
• DO NOT apply more than 87.0* fl oz/A (1.59 lbs ai/A) of Cheetah on corn per year. * Maximum annual
|
||
rate in California is 44 fl oz/A (0.8 lbs ai/A).
|
||
• DO NOT exceed the maximum single application rate of 43 fl oz/A (0.79 lb ai/A).
|
||
• DO NOT use nitrogen solutions as spray carriers.
|
||
• DO NOT apply Cheetah if corn shows injury from prior herbicide applications or environmental stress
|
||
(drought, excessive rainfall, etc.)
|
||
• DO NOT apply Cheetah through any type of irrigation system.
|
||
|
||
Refer to the ROTATIONAL CROP RESTRICTIONS section under the PRODUCT INFORMATION heading
|
||
of this label for the appropriate rotational crop plant back intervals.
|
||
|
||
ϮϮ
|
||
|
||
APPLICATION DIRECTIONS FOR USE ON COTTON CONTAINING THE GLUFOSINATE
|
||
RESISTANT GENE
|
||
Uniform, thorough spray coverage is necessary to achieve consistent weed control. Cheetah may be
|
||
applied as a broadcast, over-the-top, post-emergence spray or as a directed spray only to cotton containing
|
||
the glufosinate-resistant gene.
|
||
|
||
Application Timing:
|
||
Apply to small and actively growing weeds, targeting less than 3 inch weeds in height. For additional
|
||
information on weed heights refer to the WEED CONTROL FOR ROW CROPS section.
|
||
Weed control may be reduced if application is made when heavy dew, fog, and mist/rain are present; or
|
||
when weeds are under stress due to drought, cool temperatures, or extended periods of cloudiness.
|
||
Cheetah is a foliar-active material with little or no soil-residual activity.
|
||
Cheetah is rainfast 4 hours after application, therefore, rainfall within 4 hours may necessitate retreatment.
|
||
For best result:
|
||
x On lambsquarters, Palmer amaranth and velvetleaf control, make applications of Cheetah between
|
||
dawn and 2 hours before sunset.
|
||
x Warm temperatures, high humidity, and bright sunlight improve the performance of Cheetah.
|
||
Apply Cheetah to cotton from emergence up to the early bloom stage at 29.0 fl oz/A (0.53 lbs ai/A). If
|
||
environmental conditions prevent a timely herbicide application, a single application of up to 43.0 fl oz/A
|
||
(0.79 lbs ai/A) of Cheetah may be made to cotton. If more than 29.0 fl oz/A (0.53 lbs ai/A) are used in any
|
||
single application, the annual total may not exceed 72.0 fl oz/A (1.32 lbs ai/A), including all application
|
||
timings. See Restrictions to the Directions for use on Cotton Containing the Glufosinate-Resistant
|
||
Gene below for additional information.
|
||
|
||
Application Rates:
|
||
Option 1
|
||
3 post applications
|
||
Apply 29 fl oz/A (0.53 lbs ai/A) per application depending on weed species, size and density per weed
|
||
chart. If required a second application of 29 fl oz/A (0.53 lbs ai/A) can be applied, followed by a third
|
||
application of 29 fl oz/A (0.53 lbs ai/A). The sequential applications must be made 10-14 days after each
|
||
other. The maximum annual rate of Cheetah on cotton is 87.0 fl oz/A (1.59 lbs ai/A).
|
||
Use a minimum spray volume of 15 gallons per acre, unless there is a difficult to control situation
|
||
(including dense canopy, large weeds or unfavorable growing conditions are present). In difficult to
|
||
control situations use a minimum spray volume of 20 gallons per acre.
|
||
|
||
Option 2
|
||
2 post applications
|
||
Apply 32 - 43 fl oz/A (0.59 – 0.79 lbs ai/A) per application depending on weed species, size and density
|
||
per weed chart.
|
||
If required a second application of 29 fl oz/A (0.53 lbs ai/A) can be applied.
|
||
The sequential applications must be made 10-14 days after each other.
|
||
The maximum annual rate of Cheetah on cotton is 72 fl oz/A (1.32 lbs ai/A).
|
||
Use a minimum spray volume o 15 gallons per acre, unless there is a difficult to control situation
|
||
(including dense canopy, large weeds or unfavorable growing conditions are present). In difficult to
|
||
control situations use a minimum spray volume of 20 gallons per acre.
|
||
|
||
Use
|
||
Pattern 1st Application
|
||
2nd Application
|
||
Minimum 10 Days Up
|
||
to 14 Days After 1st
|
||
Application
|
||
3rd Application
|
||
Minimum 10 Days Up
|
||
to 14 Days After 2nd
|
||
Application
|
||
Annual
|
||
Maximum
|
||
Option 1 29 fl oz/A
|
||
(0.53 lbs ai/A)
|
||
29 fl oz/A
|
||
(0.53 lbs ai/A)
|
||
29 fl oz/A
|
||
(0.53 lbs ai/A)
|
||
87 fl oz/A
|
||
(1.59 lbs ai/A)
|
||
Option 2 32-43 fl oz/A
|
||
(0.59 – 0.79 lbs ai/A)
|
||
29 fl oz/A
|
||
(0.53 lbs ai/A) None 72 fl oz/A
|
||
(1.32 lbs ai/A)
|
||
|
||
Ϯϯ
|
||
|
||
Tank Mix on Cotton Containing the Glufosinate-Resistant Gene͗
|
||
It is the pesticide user’s responsibility to ensure that all products are registered for the intended use. Read
|
||
and follow the applicable restrictions and limitations and directions for use on all product labels involved in
|
||
tank mixing. Users must follow the most restrictive directions for use and precautionary statements of each
|
||
product in the tank mixture.
|
||
Certain herbicide tank mixes may aid in the performance of Cheetah. Cheetah may be applied in tank mix
|
||
combinations with labeled rates of other products provided these other products are labeled for the timing
|
||
and method of application for the cotton to be treated. The tank mix partner must be used in accordance
|
||
with the label limitations and precautions. No label dosage rates may be exceeded. Cheetah cannot be
|
||
mixed with any product containing a label prohibition against such mixing.
|
||
|
||
Adjuvants:
|
||
Ammonium sulfate (AMS) may be used at 1.5 to 3.0 pounds per acre. Adjuvant rates are dependent on a
|
||
variety of factors including tank mix partners, environmental conditions (including temperature) and
|
||
potential for leaf burn.
|
||
AMS has shown to improve weed control of difficult-to-control weeds, like lambsquarters and velvetleaf,
|
||
under difficult environmental conditions (including low relative humidity) or hard water.
|
||
The use of an anti-foam agent is advised.
|
||
|
||
Surfactants / Oils:
|
||
The use of additional surfactants or crop oils in tank mixes with Cheetah may increase the risk of crop
|
||
response. Please refer to the surfactant label for more detailed information.
|
||
|
||
|
||
Restrictions to the Directions For Use on Cotton Containing the Glufosinate-resistant gene:
|
||
• DO NOT apply Cheetah to cotton containing the Glufosinate-resistant gene in Florida, South of Tampa
|
||
(Florida Route 60), or in Hawaii, except for test plots or breeding nurseries.
|
||
• DO NOT apply Cheetah within 70 days prior to cotton harvest.
|
||
• Up to 3 applications of Cheetah may be made to cotton per year at a maximum application rate of 29.0 fl
|
||
oz/A (0.53 lb ai/A). DO NOT apply more than 87.0 fluid ounces (including all application timings) to
|
||
cotton (1.59 lbs ai/A) per year under this application scenario. Sequential applications must be at least
|
||
10 days apart.
|
||
• If environmental conditions prevent timely applications resulting in large weeds or heavy infestations, a
|
||
single application of Cheetah at up to 43.0 fl oz/A (0.79 lb ai/A) may be made to cotton. DO NOT apply
|
||
more than 43.0 fluid ounces (0.79 lb ai/A) of Cheetah in a single application under this use scenario. If a
|
||
single application greater than 29.0 fluid ounces (0.53 lb ai/A) is made, a subsequent application not to
|
||
exceed 29.0 fluid ounces (0.53 lb ai/A) may be made to cotton. The annual total use rate under this
|
||
scenario may not exceed 72.0 fluid ounces (1.32 lb ai/A) of Cheetah. Sequential applications must be at
|
||
least 10 days apart.
|
||
• DO NOT apply Cheetah through any type of irrigation system.
|
||
• Refer to the ROTATIONAL CROP RESTRICTIONS section under the PRODUCT INFORMATION
|
||
heading of this label for the appropriate rotational crop plant back intervals.
|
||
|
||
|
||
APPLICATION DIRECTIONS FOR USE ON COTTON
|
||
|
||
Application of Cheetah to cotton varieties not containing the Glufosinate-resistant gene requires the use of
|
||
hooded spray equipment designed to minimize exposure of the spray to the cotton stand. Uniform, thorough
|
||
spray coverage is necessary to achieve consistent weed control.
|
||
|
||
Application Timing:
|
||
Apply to small and actively growing weeds, targeting less than 3 inch weeds in height. For additional
|
||
information on weed heights refer to the WEED CONTROL FOR ROW CROPS section.
|
||
Weed control may be reduced if application is made when heavy dew, fog, and mist/rain are present; or
|
||
when weeds are under stress due to drought, cool temperatures, or extended periods of cloudiness.
|
||
Applications for Cheetah on cotton may be made from emergence up to early bloom.
|
||
Cheetah is a foliar-active material with little or no soil-residual activity.
|
||
|
||
Ϯϰ
|
||
|
||
Cheetah is rainfast 4 hours after application, therefore, rainfall within 4 hours may necessitate retreatment.
|
||
For best result:
|
||
x On lambsquarters, Palmer amaranth and velvetleaf control, make applications of Cheetah between
|
||
dawn and 2 hours before sunset.
|
||
x Warm temperatures, high humidity, and bright sunlight improve the performance of Cheetah.
|
||
|
||
Application Rates:
|
||
Option 1
|
||
3 post applications
|
||
Apply 29 fl oz/A (0.53 lbs ai/A) per application depending on weed species, size and density per weed
|
||
chart.
|
||
If required a second application of 29 fl oz/A (0.53 lbs ai/A) can be applied, followed by a third application
|
||
of 29 fl oz/A (0.53 lbs ai/A).
|
||
The sequential applications must be made 10-14 days after each other.
|
||
The maximum annual rate of Cheetah on cotton is 87.0 fl oz/A (1.59 lbs ai/A).
|
||
Use a minimum spray volume of 15 gallons per acre, unless there is a difficult to control situation
|
||
(including dense canopy, large weeds or unfavorable growing conditions are present). In difficult to
|
||
control situations use a minimum spray volume of 20 gallons per acre.
|
||
|
||
Option 2
|
||
2 post applications
|
||
Apply 32 - 43 fl oz/A (0.59 – 0.79 lbs ai/A) per application depending on weed species, size and density
|
||
per weed chart.
|
||
If required a second application of 29 fl oz/A (0.53 lbs ai/A) can be applied.
|
||
The sequential applications must be made 10-14 days after each other.
|
||
The maximum annual rate of Cheetah on cotton is 72 fl oz/A (1.32 lbs ai/A).
|
||
Use a minimum spray volume o 15 gallons per acre, unless there is a difficult to control situation
|
||
(including dense canopy, large weeds or unfavorable growing conditions are present). In difficult to
|
||
control situations use a minimum spray volume of 20 gallons per acre.
|
||
|
||
Use Pattern
|
||
1st Application
|
||
2nd Application
|
||
Minimum 10 Days Up
|
||
to 14 Days After 1st
|
||
Application
|
||
3rd Application
|
||
Minimum 10 Days Up
|
||
to 14 Days After 2nd
|
||
Application
|
||
Annual
|
||
Maximum
|
||
Option 1 29 fl oz/A
|
||
(0.53 lbs ai/A)
|
||
29 fl oz/A
|
||
(0.53 lbs ai/A)
|
||
29 fl oz/A
|
||
(0.53 lbs ai/A)
|
||
87 fl oz/A
|
||
(1.59 lbs ai/A)
|
||
Option 2 32-43 fl oz/A
|
||
(0.59 – 0.79 lbs ai/A)
|
||
29 fl oz/A
|
||
(0.53 lbs ai/A) None 72 fl oz/A
|
||
(1.32 lbs ai/A)
|
||
|
||
|
||
Adjuvants:
|
||
Ammonium sulfate (AMS) may be used at 1.5 to 3.0 pounds per acre. Adjuvant rates are dependent on a
|
||
variety of factors including tank mix partners, environmental conditions (including temperature) and
|
||
potential for leaf burn.
|
||
AMS has shown to improve weed control of difficult-to-control weeds, like lambsquarters and velvetleaf,
|
||
under difficult environmental conditions (including low relative humidity) or hard water.
|
||
The use of an anti-foam agent is advised.
|
||
|
||
Surfactants / Oils:
|
||
The use of additional surfactants or crop oils in tank mixes with Cheetah may increase the risk of crop
|
||
response. Please refer to the surfactant label for more detailed information.
|
||
|
||
Application Methods to Cotton:
|
||
Application of Cheetah to cotton varieties not containing the Glufosinate-resistant gene requires the use of
|
||
hooded spray equipment designed to minimize exposure of the spray to the cotton stand. A hooded sprayer
|
||
|
||
Ϯϱ
|
||
|
||
directs the spray onto weeds, while shielding the cotton stand from contact. Use nozzles that provide
|
||
uniform coverage within the treated area. Keep hoods on these sprayers adjusted to protect desirable
|
||
vegetation. Extreme care must be exercised to avoid exposure of the desirable vegetation to the spray.
|
||
With a hooded sprayer, the spray pattern is completely enclosed on the top and all 4 sides by a hood,
|
||
thereby shielding the crop from the spray solution. This equipment must be set up and operated in a manner
|
||
that avoids bouncing or raising the hoods off the ground in any way. The spray hoods must be operated on
|
||
the ground or skimming across the ground. Tractor speed must be adjusted to avoid bouncing of the spray
|
||
hoods. Avoid operation on rough or sloping ground where the spray hoods might be raised off the ground.
|
||
If the hoods are raised, spray particles may escape and come into contact with the cotton, causing damage
|
||
or destruction of the crop.
|
||
Herbicide rates and spray volume instructions are presented as broadcast equivalents and must be reduced
|
||
in proportion to the area actually treated. Use the following formulas to calculate the correct rate and volume
|
||
per planted (field) acre:
|
||
|
||
Band width in
|
||
inches x Broadcast RATE per
|
||
acre = Amount of banded product needed per acre Row width in
|
||
inches
|
||
|
||
Band width in
|
||
inches x Broadcast spray VOLUME
|
||
per acre = Banded spray volume needed per acre Row width in
|
||
inches
|
||
|
||
Post-Harvest – Fall Burndown:
|
||
Cheetah may be applied as a post-harvest burndown treatment to fields (after cotton harvest). Up to 43.0
|
||
fl oz/A (0.79 lb ai/A) of Cheetah may be applied in a single application to control larger weeds growing in
|
||
the crop at the time of harvest. If more than 29.0 fl oz/A (0.53 lb ai/A) is used in a single application, the
|
||
annual total may not exceed 72.0 fl oz/A (1.32 lb ai/A), including all application timings.
|
||
|
||
Tank Mix on Cotton:
|
||
It is the pesticide user’s responsibility to ensure that all products are registered for the intended use. Read
|
||
and follow the applicable restrictions and limitations and directions for use on all product labels involved in
|
||
tank mixing. Users must follow the most restrictive directions for use and precautionary statements of each
|
||
product in the tank mixture.
|
||
Certain herbicide tank mixes may aid in the performance of Cheetah. Cheetah may be applied in tank mix
|
||
combinations with labeled rates of other products provided these other products are labeled for the timing
|
||
and method of application for the cotton to be treated. The tank mix partner must be used in accordance
|
||
with the label limitations and precautions. No label dosage rates may be exceeded. Cheetah cannot be
|
||
mixed with any product containing a label prohibition against such mixing.
|
||
|
||
RESTRICTIONS TO THE DIRECTIONS FOR USE ON COTTON
|
||
x [DO NOT apply to cotton in Florida, South of Tampa (Florida Route 60), or in Hawaii, except for
|
||
test plots or breeding nurseries.]
|
||
x DO NOT apply within 70 days prior to cotton harvest.
|
||
x Up to 3 applications may be made to cotton per year at a maximum application rate of 29 fl oz/A
|
||
(0.53 lb ai/A).
|
||
x DO NOT apply more than 87 fl oz (1.59 lb ai/A) (including all application timings) to cotton per
|
||
year.
|
||
x Minimum retreatment interval is 10 days.
|
||
x If environmental conditions prevent timely applications resulting in large weeds or heavy
|
||
infestations, a single application at up to 43 fl oz/A (0.79 lb ai/A) may be made to cotton. DO NOT
|
||
apply more than 43 fl oz/A (0.79 lb ai/A) in a single application under this use scenario.
|
||
x DO NOT apply this product through any type of irrigation system.
|
||
x Refer to the "Rotational Crop Restrictions" section under the "Product Information" heading
|
||
of this label for the appropriate rotational crop plant back intervals.
|
||
|
||
Ϯϲ
|
||
|
||
|
||
APPLICATION DIRECTIONS FOR USE ON SOYBEANS CONTAINING THE
|
||
GLUFOSINATE-RESISTANT GENE
|
||
Apply Cheetah only to soybeans containing the Glufosinate-resistant gene. Uniform, thorough spray
|
||
coverage is necessary to achieve consistent weed control.
|
||
|
||
Application Timing:
|
||
Apply to small and actively growing weeds, targeting less than 3 inch weeds in height. For additional
|
||
information on weed heights refer to the WEED CONTROL FOR ROW CROPS section.
|
||
Weed control may be reduced if application is made when heavy dew, fog, and mist/rain are present; or
|
||
when weeds are under stress due to drought, cool temperatures, or extended periods of cloudiness.
|
||
Applications for Cheetah on soybeans may be made from emergence up to bloom or R1 growth stage.
|
||
Cheetah is a foliar-active material with little or no soil-residual activity.
|
||
Cheetah is rainfast 4 hours after application, therefore, rainfall within 4 hours may necessitate retreatment.
|
||
For best result:
|
||
x On lambsquarters, Palmer amaranth and velvetleaf control, make applications of Cheetah between
|
||
dawn and 2 hours before sunset.
|
||
x Warm temperatures, high humidity, and bright sunlight improve the performance of Cheetah.
|
||
|
||
Application Rate:
|
||
Apply Cheetah at 29 – 43* fl oz/A (0.53 – 0.79 lbs ai/A), depending on weed species, size and density per
|
||
weed chart. *Maximum rate in California is 36 fl oz/A (0.66 lbs ai/A)
|
||
If a second application is needed, make the second application of 29 – 43* fl oz/A (0.53 – 0.79 lbs ai/A),
|
||
can be applied up to a yearly maximum of 87.0* fl oz/A (1.59 lbs ai/A). *Maximum rate in California is 36 fl
|
||
oz/A (0.66 lbs ai/A) and maximum annual rate in California is 72 fl oz/A (1.32 lbs ai/A).
|
||
The maximum annual rate of Cheetah on soybeans is 87.0* fl oz/A (1.59 lbs ai/A). *Maximum annual rate
|
||
in California is 72 fl oz/A (1.32 lbs ai/A)
|
||
Use a minimum spray volume of 15 gallons per acre, unless there is a difficult to control situation
|
||
(including dense canopy, large weeds or unfavorable growing conditions are present). In difficult to
|
||
control situations use a minimum spray volume of 20 gallons per acre.
|
||
|
||
Use Pattern Rate Ranges
|
||
1st Application
|
||
2nd Application
|
||
Minimum of 5 Days After 1st
|
||
Application
|
||
Annual Maximum
|
||
29.0 to 43.0* fI oz/A (0.53 –
|
||
0.79 lbs ai/A)
|
||
29.0 to 43.0* fI oz/A (0.53 – 0.79
|
||
lbs ai/A)
|
||
87.0* fI oz/A (1.59 lbs ai/A)
|
||
*Maximum rate in California is 36 fl oz/A (0.66 lbs ai/A) with annual maximum of 72 fl oz/A (1.32 lbs ai/A).
|
||
|
||
|
||
Adjuvants:
|
||
Ammonium sulfate (AMS) may be used at 1.5 to 3.0 pounds per acre. Adjuvant rates are dependent on a
|
||
variety of factors including tank mix partners, environmental conditions (including temperature) and
|
||
potential for leaf burn.
|
||
AMS has shown to improve weed control of difficult-to-control weeds, like lambsquarters and velvetleaf,
|
||
under difficult environmental conditions (including low relative humidity) or hard water.
|
||
The use of an anti-foam agent is advised.
|
||
|
||
Surfactants / Oils:
|
||
The use of additional surfactants or crop oils in tank mixes with Cheetah may increase the risk of crop
|
||
response. Please refer to the surfactant label for more detailed information.
|
||
|
||
Restrictions to the Directions For Use onSoybeans Containing the Glufosinate-resistant gene:
|
||
• DO NOT apply Cheetah within 70 days of harvesting soybean seed.
|
||
• DO NOT apply more than 87.0 fl oz/A (1.59 lbs ai/A) of Cheetah on soybeans per growing year.
|
||
• DO NOT apply more than 43.0* fl oz/A (0.79 lbs ai/ A) of Cheetah in a single application. *Maximum rate
|
||
in California is 36 fl oz/A (0.66 lbs ai/A)
|
||
|
||
Ϯϳ
|
||
|
||
• DO NOT make more than 3 applications per year.
|
||
• DO NOT graze the treated crop or cut for hay.
|
||
• DO NOT use nitrogen solutions as spray carriers. A silicone-based antifoam agent may be added if
|
||
needed.
|
||
• DO NOT apply Cheetah if soybeans show injury from prior herbicide applications or environmental
|
||
stress (drought, excessive rainfall, etc.).
|
||
• DO NOT apply Cheetah through any type of irrigation system.
|
||
• Refer to the ROTATIONAL CROP RESTRICTIONS section under the PRODUCT INFORMATION
|
||
heading of this label for the appropriate rotational crop plant back intervals.
|
||
• Sequential applications must be at least 5 days apart.
|
||
|
||
Soybean Tank Mix Instructions:
|
||
It is the pesticide user’s responsibility to ensure that all products are registered for the intended use. Read
|
||
and follow the applicable restrictions and limitations and directions for use on all product labels involved in
|
||
tank mixing. Users must follow the most restrictive directions for use and precautionary statements of each
|
||
product in the tank mixture.
|
||
Certain herbicide tank mixes may complement Cheetah. No additional surfactant is needed with any tank
|
||
mix partner. Cheetah may be applied in tank mix combinations with labeled rates of other products provided
|
||
these other products are labeled for the timing and method of application for the soybean to be treated. The
|
||
tank mix partner must be used in accordance with the label limitations and precautions. No label dosage
|
||
rates may be exceeded. Cheetah cannot be mixed with any product containing a label prohibition against
|
||
such mixing.
|
||
|
||
APPLICATION DIRECTIONS FOR CANOLA, CORN, COTTON, AND SOYBEAN SEED
|
||
PROPAGATION
|
||
Cheetah may be applied to select out susceptible “segregates”, i.e., canola, corn, cotton, and soybean
|
||
plants that DO NOT contain the Glufosinate-resistant gene during seed propagation.
|
||
• Canola Containing as Glufosinate-resistant gene:
|
||
Cheetah may also be used in canola seed propagation as a foliar spray to selectively eliminate
|
||
canola plants that DO NOT carry a gene that imparts resistance to glufosinate-ammonium and as such,
|
||
can be applied to remove susceptible segregates during canola seed propagation. Breeding material not
|
||
possessing the glufosinate-ammonium resistance gene will be severely injured or killed if treated with this
|
||
herbicide. See APPLICATION DIRECTIONS FOR USE ON CANOLA CONTAINING THE
|
||
GLUFOSINATE-RESISTANT GENE for use rates and application timing.
|
||
• Corn Containing the Glufosinate-resistant gene:
|
||
Inbred lines, plants not containing the Glufosinate-resistant gene, will be severely injured or killed
|
||
if treated with this herbicide. A hooded sprayer may be used to protect plants from coming into contact with
|
||
the herbicide application. For the selection of resistant corn “segregates,” Cheetah may be applied at 22.0
|
||
fl oz/A (0.4 lbs ai/A) plus AMS at 3.0 pounds per acre (17.0 pounds per 100 gallons) when corn is in the V-
|
||
3 to V-4 stage of growth, i.e., 3 to 4 developed collars. A second treatment of 22.0 fl oz/A (0.4 lbs ai/ A)
|
||
plus AMS at 3.0 pounds per acre may be applied when the corn is in the V-6 to V-7 stage of growth or up
|
||
to 24 inches tall. Sequential applications must be at least 10 days apart. When temperatures exceed 85 °F,
|
||
the rate of AMS can be reduced to 1.5 pounds per acre (8.5 pounds per 100 gallons) to reduce potential
|
||
leaf burn.
|
||
• Cotton Containing the Glufosinate-resistant gene:
|
||
Cheetah may also be used in cotton seed propagation as a foliar spray to selectively eliminate
|
||
cotton plants that DO NOT carry the Glufosinate-resistant gene and as such, can be applied to remove
|
||
susceptible segregates during cotton seed propagation. Breeding material not containing the Glufosinate-
|
||
resistant gene will be severely injured or killed if treated with this herbicide. See APPLICATION
|
||
DIRECTIONS FOR USE ON COTTON CONTAINING THE GLUFOSINATE-RESISTANT GENE for use
|
||
rates and application timing.
|
||
• Soybeans Containing the Glufosinate-resistant gene:
|
||
For the selection of resistant soybean “segregates,” Cheetah may be applied at up to 29.0 to
|
||
43.0* fl oz/A (0.53 – 0.79 lbs ai/A) when soybean is in the third trifoliate stage. A second treatment of 29.0
|
||
to 43.0* fl oz/A (0.53 – 0.79 lbs ai/A) may be applied up to but not including the bloom growth stage of
|
||
soybean. Sequential applications must be at least 5 days apart. * Maximum rate in California is 36 fl oz/A
|
||
(0.66 lbs ai/A)
|
||
|
||
Ϯϴ
|
||
|
||
APPLICATION DIRECTIONS FOR USE ON LISTED TREE, VINE, AND BERRY CROPS
|
||
Apply this to the tree, vine, and berry crops listed below. Uniform, thorough spray coverage is necessary to
|
||
achieve consistent weed control.
|
||
|
||
REGISTERED CROPS
|
||
BERRIES:
|
||
Crop Subgroup 13-B: Bushberry subgroup
|
||
Blueberry, highbush; blueberry, lowbush; currant; elderberry; gooseberry; huckleberry
|
||
Juneberry; lingonberry; salal
|
||
CITRUS CROP GROUP 10-10:
|
||
Orange or tangerine/mandarin, Calamondin; citron, citrus hybrids; Mediterranean Mandarin; orange, sour;
|
||
orange, sweet; satsuma darin; tachibana orange; tangerine (mandarin); tangelo; tangor, trifoliate orange;
|
||
cultivars, varieties and/or hybrids of these
|
||
Lemon or lime – Australian desert lime; Australian finger lime; Australian round lime; brown river finger
|
||
lime;
|
||
kumquat; lemon; lime; mount white lime; New Guinea wild lime; Russel River lime; sweet lime; Tahiti lime;
|
||
cultivars, varieties and/or hybrids of these Grapefruit – Grapefruit; Japanese summer grapefruit;
|
||
pummelo; tangelo; uniq fruit; cultivars, varieties and/or hybrids of these.
|
||
|
||
OLIVES: all olive varieties
|
||
|
||
POME FRUIT (CROP GROUP 11-10):
|
||
Crop Group 11. Pome Fruits Group
|
||
Apple; crabapple; loquat; mayhaw; pear; pear, oriental; quince; azarole; hook; medlar; quince, Chinese;
|
||
quince, Japanese; tejocote; cultivars, varieties and/or hybrids of these
|
||
|
||
STONE FRUIT (CROP GROUP 12-12):
|
||
Crop Group 12. Stone Fruits Group
|
||
Apricot; cherry, sweet; cherry, tart; nectarine, peach; plum; plum, chicksaw; damson; plum, Japanese;
|
||
plumcot; prune; capulin; jujube and sloe; cultivars, varieties and/or hybrids of these.
|
||
|
||
TREE NUTS (CROP GROUP 14 INCLUDING PISTACHIOS):
|
||
Crop Group 14. Tree Nuts Group
|
||
Almond; beech nut; Brazil nut; butternut; cashew; chestnut; chinquapin; filbert (hazelnut), hickory nut,
|
||
macadamia nut (bush nut), pecan, pistachios, and walnut, black and English
|
||
|
||
GRAPES: all grape varieties (table, wine, and raisins)
|
||
|
||
Application Rate and Timing͗
|
||
For best results, apply to emerged, young, actively growing weeds. Warm temperatures, high humidity, and
|
||
bright sunlight improve the performance of Cheetah. Weed control may be reduced when applications are
|
||
made to weeds under stress due to drought or cool temperatures. Weeds under stress or in dense
|
||
populations will require application at the highest specified label use rate. Stressed conditions also include
|
||
prior treatments of other contact or systemic herbicides. DO NOT retreat these weeds with Cheetah until
|
||
sufficient regrowth has occurred.
|
||
|
||
Apply Cheetah as a directed spray to control undesirable vegetation in tree, vine, and berries listed on this
|
||
label. Apply as a broadcast, banded, or spot treatment application depending on the situation to control
|
||
weeds listed under the heading Weeds Controlled in Tree, Vine and Berry Crops. Avoid direct spray or
|
||
drift to desirable vegetation. Regrowth may occur due to the weed stage of growth at application, low use
|
||
rate, or environmental conditions. Repeat applications of Cheetah may be necessary to control plants
|
||
generating from underground parts or seed.
|
||
|
||
Avoid contact of Cheetah solution, spray, drift or mist with green bark, stems, or foliage, as injury may occur
|
||
to trees, vines, and berries. Only trunks with callused, mature brown bark may be sprayed unless
|
||
protected from spray contact by nonporous wraps, grow tubes, or waxed containers. Contact of
|
||
Cheetah with parts of trees, vines, or berries other than mature brown bark can result in serious
|
||
|
||
Ϯϵ
|
||
|
||
damage.
|
||
|
||
Application Methods for Broadcast Applications:
|
||
Apply Cheetah at the rates listed below for broadcast applications based on weed size and stage of
|
||
growth.
|
||
Weed Size and Stage Rate of this product
|
||
Weeds < 3 in height 48 fl oz/A (0.88 lbs ai/A)
|
||
Weeds < 6 in height
|
||
pre tiller grasses 56 fl oz/A (1.02 lbs ai/A)
|
||
Weeds > 6 in height
|
||
and/or grasses that have tillered 56-82 fl oz/A (1.02 – 1.5 lbs ai/A)
|
||
|
||
Application Methods for Banded Spray Applications:
|
||
Banded applications may be used using the following formula to calculate the amount of herbicide
|
||
needed for orchard or vineyard strip sprays:
|
||
|
||
|
||
Band width in inches x Rate per acre
|
||
broadcast = Amount of herbicide needed for treatment Row width in inches
|
||
|
||
Application Methods for Spot or Directed-Spray Applications:
|
||
For spot or directed spray applications: mix Cheetah at 1.7 fluid ounces of product (0.031 lbs ai) per gallon
|
||
of water. Apply to undesirable vegetation foliage until wet but prior to runoff. Ensure uniform and complete
|
||
coverage. Thoroughly clean the sprayer following use. DO NOT make spot or directed spray applications
|
||
to tree or vine trunk as injury may occur.
|
||
|
||
Weeds Controlled in Tree, Vine and Berry Crops:
|
||
Broadleaf Weeds
|
||
Alkali sida Fleabane, annual Morningglory, ivyleaf Smartweed, Pennsylvania
|
||
Ammannia, purple Goosefoot Morningglory, pitted Sowthistle, annual
|
||
Arrowhead, California Gromwell, field Mullein, turkey Spurge, prostrate
|
||
Buckwheat, wild Groundcherry, cutleaf Mustard, wild Starthistle, yellow
|
||
Buffalobur Groundsel, common Nettle Sunflower, common
|
||
Burclover, California Henbit Nightshade, black Sunflower, prairie
|
||
Carpetweed Jimsonweed Nightshade, eastern
|
||
black
|
||
Sunflower, volunteer
|
||
Chickweed, common Knotweed Nightshade, hairy Swinecress
|
||
Chinese thornapple Kochia Pennycress Thistle, Russian
|
||
Cocklebur, common Lambsquarters,
|
||
common
|
||
Pigweed, redroot Turnip, wild
|
||
Copperleaf, Virginia Lettuce, miner’s Pineapple-weed Velvetleaf
|
||
Cudweed Lettuce, prickly Puncturevine Vervain
|
||
Cutleaf eveningprimrose London rocket Purslane, common Vetch
|
||
Dodder Mallow, common Radish, wild Virginia copperleaf
|
||
Eclipta Malva (little mallow) Ragweed, common Willowherb, panicle
|
||
Fiddleneck Marestail Ragweed, giant
|
||
Filaree Mayweed Redmaids
|
||
Filaree, redstem Morningglory, entireleaf Shepherd’s-purse
|
||
|
||
ϯϬ
|
||
|
||
Grass Weeds
|
||
Barnyardgrass Crabgrass, smooth Junglerice Shattercane
|
||
Bluegrass, annual Cupgrass, woolly Oat, wild Sprangletop
|
||
Brome, ripgut Foxtail, giant Panicum, fall Stinkgrass
|
||
Bromegrass, downy Foxtail, green Panicum, Texas Wheat, volunteer
|
||
Canarygrass Foxtail, yellow Rush, toad** Windgrass
|
||
Chess, soft Goosegrass Ryegrass, annual* Witchgrass
|
||
Crabgrass, large Johnsongrass, seedling Sandbur, field
|
||
|
||
Biennial and Perennial Weeds
|
||
Aster, white heath Clover, red Horsetail Paragrass Thistle, musk
|
||
Bindweed, field Clover, white Lovegrass Plantain Torpedograss
|
||
Bindweed, hedge Dallisgrass Mugwort Poison ivy/oak Vaseygrass
|
||
Bluegrass,
|
||
Kentucky Dandelion Mullein, common Quackgrass Woodsorrel
|
||
Bromegrass,
|
||
smooth Dock, curly Mustard, tansy Rocket, yellow Yarrow, common
|
||
Bulrush** Dogbank (hemp) Nutsedge, purple Rose, wild
|
||
Burdock Fescue Nutsedge, yellow Rubus spp.
|
||
Canada thistle Golden rod, gray Onion, wild Spurge, leafy
|
||
Clover, Alsike Guineagrass Orchardgrass Thistle, bull
|
||
* apply to annual ryegrass prior to 3 inches in height
|
||
**indicates suppression
|
||
|
||
Restrictions to the Directions For Use on Tree, Vine, and Berry Crops:
|
||
• DO NOT apply more than 164 fluid ounces of Cheetah per acre (3.0 lbs ai/A) to berry bushes and stone
|
||
fruit in a 12 month period.
|
||
• DO NOT exceed the maximum single application rate of 82 fl oz/A (1.50 lb ai/A)
|
||
• DO NOT make more than 2 applications at a maximum application rate of 82 fl oz/A (1.5 lbs ai/A) per
|
||
application to berry bushes and stone fruit.
|
||
• DO NOT apply more than 246 fl oz (4.5 lbs ai/A) of Cheetah per acre to tree, nuts, vines, pome fruit,
|
||
citrus and olives in any calendar year.
|
||
• DO NOT make more than 3 applications at a maximum rate of 82 fl oz/A (1.50 lb ai/A) per application to
|
||
tree nuts, vines, pome fruits, citrus and olives.
|
||
• DO NOT graze harvest, and/or feed treated orchard cover crops to livestock.
|
||
• DO NOT apply Cheetah through any type of irrigation system.
|
||
• DO NOT apply Cheetah aerially to tree, berry, or vine crops.
|
||
• DO NOT apply Cheetah within 14 days of nut, fruit, berry, or grape harvest.
|
||
• Applications to citrus fruits, pome fruits, olives and berry bushes must be a minimum of 14 days apart.
|
||
• Applications to stone fruit must be a minimum of 28 days apart.
|
||
• DO NOT make spot spray applications to suckers, as tree injury may occur.
|
||
|
||
Sucker Control with Cheetah:
|
||
Cheetah will reduce or eliminate sucker growth when applied to suckers that are young, green, and
|
||
uncallused. For sucker control, apply a split application approximately 4 weeks apart at 56.0 fluid ounces
|
||
of product per acre (1.02 lbs ai/A). Coverage of all sucker foliage is necessary for optimum control. Suckers
|
||
must not exceed 12 inches in length.
|
||
|
||
Tank Mix Partner Instructions:
|
||
It is the pesticide user’s responsibility to ensure that all products are registered for the intended use. Read
|
||
and follow the applicable restrictions and limitations and directions for use on all product labels involved in
|
||
tank mixing. Users must follow the most restrictive directions for use and precautionary statements of each
|
||
product in the tank mixture.
|
||
Cheetah does not provide residual weed control or control of unexposed plant parts. Certain herbicide tank
|
||
mixes may aid in the performance of Cheetah or be added to provide residual herbicide activity. No
|
||
additional surfactant is needed with any tank mix partner. Cheetah may be applied in tank mix combinations
|
||
|
||
ϯϭ
|
||
|
||
with labeled rates of other products provided these other products are labeled for the timing and method of
|
||
application for the crop to be treated. The tank mix partner must be used in accordance with the label
|
||
limitations and precautions. No label dosage rates may be exceeded. Cheetah cannot be mixed with any
|
||
product containing a label prohibition against such mixing.
|
||
|
||
diuron
|
||
napropamide oryzalin terbacil
|
||
flumioxazin norfluazon simazine
|
||
|
||
|
||
|
||
APPLICATION DIRECTIONS FOR POTATO VINE DESICCATION
|
||
Application Rates and Timing:
|
||
Apply Cheetah at the beginning of natural senescence of potato vines. Apply 21.0 fl oz/A (0.38 lbs ai/A).
|
||
DO NOT split this application or apply more than 1 application (See restrictions section). Potato varieties
|
||
with heavy or dense vines may require an application of another desiccation product to complete vine
|
||
desiccation.
|
||
|
||
Thorough coverage of the potato vines to be desiccated is essential. Use a sufficient volume of water (20.0
|
||
to 100 gallons per acre) to obtain a thorough coverage of the potato vines. Vary the gallons of water per
|
||
acre and the spray pressure as indicated by the density of the potato vines to assure thorough spray
|
||
coverage. Increase the spray volume to at least 30.0 gallons of water per acre when the potato vine canopy
|
||
is dense or under cool and dry conditions. Apply Cheetah with the spray boom as low as possible to achieve
|
||
thorough coverage of the potato vines for best control and to minimize drift potential.
|
||
|
||
Restrictions to the Directions For Use in Potato Vine Desiccation:
|
||
• DO NOT apply more than 21.0 fl oz/A (0.38 lbs ai/A) to potato vines per year or per single application.
|
||
• DO NOT harvest potatoes until 9 days or more after application of Cheetah.
|
||
• DO NOT apply to potatoes grown for seed.
|
||
• Potatoes, canola, corn, cotton, soybean, and sugar beets may be planted at any time after the application
|
||
of Cheetah as a potato vine desiccant.
|
||
• DO NOT plant treated areas to wheat, barley, buckwheat, millet, oats, rye, sorghum, and triticale until 30
|
||
or more days after an application of Cheetah as a potato vine desiccant.
|
||
• DO NOT plant treated areas to crops other than those listed in this use precautions section until 120 or
|
||
more days after an application of Cheetah as a potato vine desiccant.
|
||
• DO NOT split this application or apply more than one application per harvest (per year).
|
||
|
||
|
||
FALLOW FIELDS OR POST HARVEST
|
||
Cheetah may be used as a substitute for tillage to control or suppress weeds in the WEED CONTROL FOR
|
||
ROW CROPS section of this label. Applications may be made in fallow fields, post harvest, prior to planting
|
||
or emergence of any crop listed on this label.
|
||
|
||
Apply Cheetah at 22.0 or 29.0 fl oz/A (0.2 to 0.53 lb ai/A) to fallow fields to control specific weeds. Cheetah
|
||
must be applied with ammonium sulfate. Tank mixes with 2,4-D, glyphosate or atrazine are specified with
|
||
Cheetah to enhance total weed control. When using Cheetah in tank mix combinations, follow the
|
||
precautions and directions of use of the most restrictive label. See APPLICATION AND MIXING
|
||
PROCEDURES section of this label for additional information on how to apply Cheetah. See the PRODUCT
|
||
INFORMATION section of this label for rotational crop restrictions.
|
||
|
||
RESTRICTIONS TO THE DIRCTIONS FOR USE ON FALLOW FIELDS OR POST HARVEST
|
||
DO NOT apply more than 29 fl oz/A (0.53 lbs ai/A) in a single application.
|
||
DO NOT make more than 3 applications per year.
|
||
DO NOT make sequential applications sooner than 14 days apart.
|
||
DO NOT apply more than 87 fl oz/A (1.59 lbs ai/A) per year.
|
||
|
||
|
||
APPLICATION DIRECTIONS FOR USE ON NONCROPLAND USE SITES
|
||
When applied as directed, Cheetah controls undesirable plant vegetation in public, military, and non-crop
|
||
areas including private, public and military lands in the following areas: airfields, airports, alleys, lanes,
|
||
|
||
ϯϮ
|
||
|
||
paths, trails, access roads, around commercial or industrial structures or outbuildings, around farm and
|
||
ranch structures and outbuildings, around ornamental gardens, around ornamental trees and shrubs
|
||
(including Christmas trees), site preparation areas for conifer and hardwood, bare ground, barrier strips,
|
||
beaches*, campgrounds, construction sites, ditch banks, drive-in theaters, driveways and ramps, dry
|
||
ditches and canals, fences and fencerows, firebreaks, golf courses* [(excluding greens, tees, aprons,
|
||
fairways and roughs)]*, gravel yards, Conservation Reserve Program (CRP)*, habitat restoration and
|
||
management areas, highways and roadsides (including aprons, medians, guardrails and right of ways),
|
||
industrial plant sites, industrial areas, lumber yards, nurseries and shade houses and greenhouses,
|
||
landscapes and mulched areas, natural areas, parking areas, parks, paved areas, petroleum and other
|
||
tank farms, pumping installations, pipeline, power, telephone and utility rights-of-way, sewage disposal
|
||
areas, fuel storage areas, power stations, preplant to turf and ornamental plants, railroad rights-of way,
|
||
recreation areas, refineries, resorts, schools, sidewalks, sports areas, storage areas, substations, tennis
|
||
courts, shelter belts, uncropped farmstead areas, vacant lots, walkways, wastelands, wildlife openings,
|
||
wildlife habitat areas, wildlife food plots*.
|
||
*Not for use in California
|
||
|
||
Industrial: This product may be used to improve line-of-sight at railroad crossings and reduce the need for
|
||
mowing along rights-of-way, and wayside structures. This product may be tank mixed with other herbicides
|
||
for these use sites unless specifically prohibited by the product label.
|
||
|
||
Conservation Reserve Program (CRP)*: This product can be used to control undesirable vegetation
|
||
when rotating out of CRP acres or to suppress competitive growth and seed production of undesirable
|
||
vegetation in CRP acres. For selective applications with broadcast spray equipment, apply 48 to to 56 fl.
|
||
oz./A (0.88 to 1.0 lb. ai/A) of this product in early spring before desirable CRP grasses, including crested
|
||
and tall wheatgrass, break dormancy and initiate green growth. Late fall applications can be made after
|
||
desirable perennial grasses have reached dormancy. Some stunting of CRP perennial grasses will occur
|
||
if applications are made when plants are not dormant.
|
||
|
||
Wildlife Food Plots*: This product may be used as a site preparation treatment prior to planting wildlife
|
||
food plots. Any wildlife food species may be planted after applying this product, or native species may be
|
||
allowed to repopulate the area. If tillage is needed to prepare a seedbed, wait 7 days after applying this
|
||
product before tilling.
|
||
|
||
Site Preparation for Conifer and Hardwood Production Areas: This product may be used as a site
|
||
preparation treatment prior to planting conifer and hardwood species. DO NOT apply Cheetah as an over-
|
||
the-top broadcast spray to desirable conifer or hardwood plantings. Seedling conifer and hardwood trees
|
||
may be planted into the treated area after the restricted entry interval (REI) of 12 hours has elapsed.
|
||
|
||
Greenhouse: This product may be used to control weeds listed on this label which are growing in
|
||
greenhouses and shadehouses. Desirable vegetation must not be present during application and air
|
||
circulation fans must be turned off.
|
||
|
||
Dormant Bermudagrass and/or Bahiagrass*: When applied to dormant Bermudagrass and/or
|
||
Bahiagrass*, this product will provide control or suppression of many winter annual weeds. Treat with 56
|
||
to 82 fl. oz./A (1.0-1.5 lb. ai/A) only when turfgrass is fully dormant in late fall or winter and prior to spring
|
||
green-up. Spot treatments or broadcast applications of this product to non-dormant turfgrass may result in
|
||
injury or delayed green-up. Avoid high volume and spot applications where spray volume exceeds 80
|
||
gallons per acre or injury or delayed greening may occur. Applications to residential lawns are limited to
|
||
spot treatments only. The maximum application rate must not exceed 4 fl. oz./gal. of water/1000 sq. ft.
|
||
(corresponding to a rate of 0.0312 lb. ai/100 sq. ft.). Applications for renovating Bermudagrass lawns
|
||
must be conducted when the weather is cool and Bermudagrass is dormant.
|
||
*Not for use in California
|
||
|
||
Side Trimming: To control only a portion of the plant, direct the spray solution to thoroughly cover
|
||
(spray to wet) only the portion of the plant to be controlled.
|
||
|
||
ϯϯ
|
||
|
||
|
||
Brush Control: This product will provide control or suppression of the perennial woody species (brush)
|
||
listed below. Use this product at rates from 1 to 3 quarts of this product per acre to impact the growth of
|
||
woody plants and not to exceed 1.9 gallons per acre per year (4.5 lb ai/A/yr). Non-ionic surfactants (NIS)
|
||
or methylated seed oils (MSO) may be used when making foliar applications. Follow any instructions on
|
||
the surfactant manufacturer’s label.
|
||
|
||
For hard-to-control woody plants including elm, certain oaks or when plant leaf surfaces have hardened
|
||
off, use the higher rate of this product or tank mix this product with other herbicides registered for control
|
||
of these woody plants. Higher specified rates per acre of this product must be used when conditions are
|
||
not optimum for spray coverage, including when weed growth is heavy or dense. Lower specified rates
|
||
must be used when the target species is conifer and when vegetation growth conditions allow for uniform
|
||
spray coverage.
|
||
|
||
* Not for use in California
|
||
|
||
|
||
USE RESTRICTIONS for NONCROP:
|
||
x DO NOT apply more than 246 fl. oz. of this product per acre per year (4.5 lb. ai/A/year).
|
||
x DO NOT apply more than 82 fl. oz. of this product per acre per single application (1.5 lb.
|
||
ai/A/application).
|
||
x DO NOT apply more than a total of 3 broadcast applications (excluding spot treatments) per year.
|
||
x DO NOT exceed a maximum total of 4.5 lb. ai/A/year.
|
||
x Minimum re-treatment interval is 5 days.
|
||
|
||
APPLICATION RATES
|
||
|
||
Mix 0.5 to 2.0 fl. oz. (0.009 to 0.036 lb. ai) of this product per gallon of spray solution (24 to 82 fl. oz./A
|
||
(0.44 to 1.5 lb. ai/A) and apply 1 gallon of spray solution to 1,000 square feet to actively growing weeds.
|
||
Adjust application rate as needed when using spray volumes delivering greater or less than 1 gallon per
|
||
1,000 square feet. Determine proper use rate based on weed size in Table 1. Larger weeds will require a
|
||
higher use rate and see Table 1 for details.
|
||
|
||
Table 1: USE RATE FOR THIS HERBICIDE
|
||
Apply this product at the rates listed below for broadcast applications based on weed size and stage of
|
||
growth.
|
||
Weed Size and Stage Rate of this
|
||
product
|
||
(Per Gallon of
|
||
Water)
|
||
Rate of this
|
||
product
|
||
(Per 1,000 sq. ft.)
|
||
Rate of this
|
||
product
|
||
(Per Acre)
|
||
Spot Spray
|
||
% Solution
|
||
Easily Controlled Weeds <
|
||
3 in height*
|
||
0.5 fl. oz.
|
||
(0.009 lb. ai)
|
||
0.5 fl. oz.
|
||
(0.009 lb. ai)
|
||
24 fl. oz./A
|
||
(0.44 lb. ai)
|
||
0.5
|
||
Weeds < 3 in height 1.0 fl. oz.
|
||
(0.018 lb. ai)
|
||
1.0 fl. oz.
|
||
(0.018 lb. ai)
|
||
48 fl. oz./A
|
||
(0.88 lb. ai)
|
||
0.5-0.75
|
||
Weeds < 6 in height pre-
|
||
tiller grasses
|
||
1.25 fl. oz.
|
||
(0.023 lb. ai)
|
||
1.25 fl. oz.
|
||
(0.023 lb. ai)
|
||
56 fl. oz./A
|
||
(1.0 lb. ai)
|
||
0.75-1.25
|
||
Weeds > 6 in height
|
||
and/or grasses that have
|
||
tillered
|
||
1.25 to 2.0 fl.
|
||
oz.
|
||
(0.023 to 0.036 lb.
|
||
ai)
|
||
1.25 to 2.0 fl. oz.
|
||
(0.023 to 0.036 lb.
|
||
ai)
|
||
56-82 fl. oz./A
|
||
(1.0 to 1.5 lb. ai)
|
||
1.25-1.5
|
||
*See Weeds Controlled Table below for details.
|
||
|
||
For spot or directed spray applications by backpack sprayers, mix this product at 0.5 to 2.0 fl. oz. of
|
||
product (0.009 to 0.036 lb. ai) per gallon of water. Larger and more difficult to control weeds require a
|
||
higher use rate. When using the per gallon rate, calibrate sprayers to deliver 1 gallon of spray solution
|
||
|
||
ϯϰ
|
||
|
||
per 1,000 square feet. Adjust application rate as needed when using spray volumes delivering greater or
|
||
less than 1 gallon per 1,000 square feet. Thorough spray coverage of weeds is necessary to maximize
|
||
weed control. Spray coverage needs to be uniform, but DO NOT spray to the point of runoff. Thoroughly
|
||
clean the sprayer following use. DO NOT make spot or directed spray applications to desired plant
|
||
foliage or stems as injury may occur.
|
||
|
||
Use Restrictions:
|
||
x DO NOT apply this product within any enclosed structure in residential or commercial
|
||
landscapes.
|
||
x DO NOT apply this product over-the-top as a broadcast application to ornamentals, conifers or
|
||
hardwood plantings.
|
||
x DO NOT apply this product over-the-top of ornamental plants, and DO NOT allow spray of this
|
||
product to contact or drift onto the foliage, green stems, exposed roots or fruit of desirable plants.
|
||
Avoid application of this product under conditions that favor drift of sprays onto desired
|
||
ornamentals or residential lawns.
|
||
|
||
This product offers postemergence control of susceptible grasses, sedges and broadleaf weeds (See
|
||
WEEDS CONTROLLED Table), as well as additional mode of action to assist in the control of resistant
|
||
weeds.
|
||
|
||
IMPORTANT: Contact with spray or spray drift of this product may cause severe injury or destruction of
|
||
certain desirable plants, especially herbaceous species including bedding plants or direct seeded annual
|
||
and perennial flowers. The use of spray shields that limit the plant exposure to this product is highly
|
||
advised when applying this product near desirable plants.
|
||
|
||
HOW TO APPLY
|
||
Spot or Directed Applications
|
||
This product may be used as a spot- or directed-spray application. Prepare the desired volume of spray
|
||
solution by mixing this product in water with the amounts indicated in the following table:
|
||
|
||
Table 2. Amount of this product added to water to make 1, 25, or 100 gallons of spray solution at
|
||
dosages of ½ to 3%. See
|
||
Table 1 for % solution to use based on target vegetation.
|
||
|
||
%
|
||
SOLUTION
|
||
VOLUME OF SPRAY SOLUTION
|
||
1 GALLON 25 GALLONS 100 GALLONS
|
||
THIS PRODUCT
|
||
0.5 % 0.75 fl. oz. 1 pint 1/2 gallon
|
||
1% 1.5 fl. oz. 1 quart 1 gallon
|
||
2% 3 fl. oz. 2 quarts 2 gallons
|
||
3% 4.5 fl. oz. 3 quarts 3 gallons
|
||
|
||
Select appropriate solution concentration and spray undesirable vegetation foliage on a spray-to-wet
|
||
basis. DO NOT apply beyond runoff. Ensure uniform and complete coverage. Use a coarse spray.
|
||
To minimize drift, avoid spraying during windy conditions. Backpack, pump-up, and hydraulic sprayers
|
||
may be used. Thoroughly clean the sprayer following use.
|
||
|
||
Use of Spray Adjuvants: The addition of a nonionic antifoaming agent may reduce foaming, especially
|
||
when using soft water. The use of Methylated seed oil (MSO) at 1% v/v (1 gal. per 100 gal. of spray
|
||
solution) or non-ionic surfactant (NIS) at a minimum rate of 0.25% v/v (1 qt. per 100 gal. of spray solution)
|
||
may be used for foliar applications. The addition of 8.5 to 17.0 lbs. of ammonium sulfate (spray grade)
|
||
per 100 gal. of water (1 to 2% by weight) or 2 to 4 lbs. of ammonium sulfate per acre may result in better
|
||
weed control.
|
||
|
||
This herbicide can be tank mixed with other non-selective herbicides including glyphosate and
|
||
preemergence residual herbicides including flumioxazin. Follow the most restrictive label restrictions and
|
||
precautions for each product. A combination with a residual herbicide including flumioxazin provides
|
||
|
||
ϯϱ
|
||
|
||
effective control of existing weeds as well as lasting residual weed control in areas including landscape
|
||
beds and xeriscapes.
|
||
|
||
Aerial Applications (Helicopter Application Only): Use a drift control device including a “Microfoil,” or
|
||
“Thru Valve-Boom” or equivalent drift control system when applying as a foliar treatment to utility rights-of-
|
||
way, tree production areas, ditch banks or other approved sites that may be near susceptible crops. The
|
||
application volume required will vary with the height and density of the vegetation and the application
|
||
equipment used. Generally, aerial applications will require a minimum of 15 gallons per acre to ensure
|
||
thorough coverage. Drift control additives may be used. If a drift control additive is used, observe and
|
||
follow all directions and precautions as specified on the additive label.
|
||
|
||
Foliar Treatments with Ground Equipment
|
||
x High Volume Applications: Use high volume applications for optimum performance when
|
||
spraying medium to high density vegetation. Use equipment calibrated to deliver 50 to 100
|
||
gallons of finished spray per acre. For best results, make sure that the targeted plant foliage is
|
||
thoroughly covered.
|
||
x Low Volume Applications: Use low volume applications when brush height is less than 6 feet
|
||
and brush cover is less than 60% of the area. Use equipment calibrated to deliver 10 to 50
|
||
gallons of finished spray per acre.
|
||
|
||
Broadcast Applications with Ground Equipment: Use equipment calibrated to deliver 20 to 100
|
||
gallons of finished spray per acre. The amount of spray solution to use will depend on the height and
|
||
density of the brush. Use spray nozzles and equipment that will provide thorough coverage of the
|
||
targeted brush species.
|
||
|
||
BRUSH* SUPPRESSED OR
|
||
CONTROLLED
|
||
Blackberry
|
||
Deer brush
|
||
|
||
Douglas fir
|
||
Gallberry
|
||
Hazel
|
||
Honeysuckle
|
||
Huckleberry
|
||
Maple
|
||
Multiflora rose
|
||
Oak
|
||
Poison ivy/oak
|
||
Pine
|
||
|
||
Roundleaf
|
||
Greenbrier
|
||
Salmonberry
|
||
Sweetgum
|
||
Sumac
|
||
Thimbleberry
|
||
Trumpetcreeper
|
||
Vine Maple
|
||
Western Red Cedar
|
||
*not for use in California
|
||
|
||
WEEDS CONTROLLED
|
||
Alfalfa+
|
||
Alkali sida
|
||
Amaranth, Palmer+
|
||
Ammannia, purple
|
||
Anoda, spurred*^
|
||
Arrowhead, California
|
||
Artichoke, Jerusalem+
|
||
Aster, white heath
|
||
Bahiagrass
|
||
Barley, volunteer*^
|
||
Barnyardgrass*
|
||
Beggarweed, Florida+
|
||
Bermudagrass+
|
||
Bindweed, field
|
||
Bindweed, hedge
|
||
Black medic+
|
||
Bluegrass, annual
|
||
Gallinsoga, small flower+
|
||
Geranium, cutleaf+
|
||
Goosefoot
|
||
Goosegrass*^
|
||
Goldenrod, gray
|
||
Gromwell, field
|
||
Groundcherry, cutleaf
|
||
Groundsell, common
|
||
Guineagrass
|
||
Hempnettle+
|
||
Henbit
|
||
Horsenettle, Carolina*^
|
||
Horsetail
|
||
Johnsongrass, rhizome+
|
||
Johnsongrass, seedling*^
|
||
Jimsonweed
|
||
Junglerice*^
|
||
Pokeweed+
|
||
Puncturevine
|
||
Purslane, common*^
|
||
Pusley, Florida+
|
||
Quackgrass
|
||
Radish, wild
|
||
Ragweed, common
|
||
Ragweed, giant
|
||
Redmaids
|
||
Rocket, yellow
|
||
Rose, wild
|
||
Rubus spp.
|
||
Rice, red+
|
||
Rice, volunteer+
|
||
Rush, toad***
|
||
Ryegrass, annual**
|
||
Sandbur, field
|
||
|
||
ϯϲ
|
||
|
||
Bluegrass, Kentucky
|
||
Blueweed, Texas+
|
||
Brome, ripgut
|
||
Bromegrass, downy
|
||
Bromegrass, smooth
|
||
Buckwheat, wild
|
||
Buffalobur
|
||
Bulrush***
|
||
Burclover, California
|
||
Burcucumber+
|
||
Burdock
|
||
Bursage, woolyleaf+
|
||
Canarygrass
|
||
Carpetgrass
|
||
Carpetweed
|
||
Catchweed bedstraw (cleavers)
|
||
*^
|
||
Chess, soft
|
||
Chickweed, common
|
||
Chickweed, mouse-ear+
|
||
Chinese thornapple
|
||
Clover, Alsike
|
||
Clover, red
|
||
Clover, white
|
||
Cocklebur, common
|
||
Copperleaf, hophornbeam+
|
||
Copperleaf, Virginia
|
||
Corn, volunteer+
|
||
Cotton, volunteer+
|
||
Crabgrass, large*^
|
||
Crabgrass, smooth*^
|
||
Croton, tropic*^
|
||
Croton, woolly*^
|
||
Cudweed
|
||
Cupgrass, woolly
|
||
Cutleaf eveningprimrose
|
||
Dallisgrass
|
||
Dandelion
|
||
Devil’s claw*^
|
||
Dock, curly
|
||
Dock, smooth+
|
||
Dodder
|
||
Dogbane (hemp)
|
||
Eclipta
|
||
Fescue
|
||
Fleabane, annual
|
||
Fiddleneck
|
||
Filaree
|
||
Filaree, redstem
|
||
Foxtail, bristly+
|
||
Foxtail, giant
|
||
Foxtail, green
|
||
Foxtail, robust purple+
|
||
Foxtail, yellow*^
|
||
Gallinsoga, hairy+
|
||
Knotweed*^
|
||
Kochia
|
||
Ladysthumb+
|
||
Lambsquarters, common
|
||
Lettuce, miners
|
||
Lettuce, prickly
|
||
London rocket
|
||
Lovegrass
|
||
Mallow, common
|
||
Mallow, Venice+
|
||
Malva (little mallow)
|
||
Marestail
|
||
Marshelder, annual+
|
||
Mayweed
|
||
Milkweed, common***+
|
||
Milkweed, honeyvine***+
|
||
Millet, wild proso+
|
||
Millet, proso volunteer+
|
||
Morningglory, entireleaf
|
||
Morningglory, ivyleaf
|
||
Morningglory, pitted
|
||
Morningglory, sharppod*^
|
||
Morningglory, smallflower+
|
||
Morningglory, tall+
|
||
Mugwort
|
||
Muhly, wirestem***+
|
||
Mullein, common
|
||
Mullein, turkey
|
||
Mustard, tansy
|
||
Mustard, wild
|
||
Nettle
|
||
Nightshade, black
|
||
Nightshade, eastern black
|
||
Nightshade, hairy
|
||
Nightshade, silverleaf+
|
||
Nutsedge, purple
|
||
Nutsedge, yellow
|
||
Oat, wild*^
|
||
Onion, wild
|
||
Orchardgrass
|
||
Panicum, fall*^
|
||
Panicum, Texas
|
||
Paragrass
|
||
Pennycress
|
||
Pigweed, redroot*^
|
||
Pigweed, prostrate*^
|
||
Pigweed, spiny*^
|
||
Pigweed, smooth*^
|
||
Pigweed, tumble*^
|
||
Pineapple weed
|
||
Plantain
|
||
Pointsettia, wild+
|
||
Poison ivy/oak
|
||
Senna coffee+
|
||
Shattercane
|
||
Shepherd’s Purse
|
||
Sicklepod (java bean)+
|
||
Sida, prickly+
|
||
Signalgrass, broadleaf*^
|
||
Smartweed, Pennsylvania
|
||
Smellmelon+
|
||
Sowthistle, annual
|
||
Sowthistle, perennial+
|
||
Soybean, volunteer+
|
||
Sprangletop
|
||
Spurge, prostrate*^
|
||
Spurge, leafy
|
||
Spurge, spotted*^
|
||
Starbur, bristly+
|
||
Starthistle, yellow
|
||
Stinkgrass
|
||
Sunflower, common
|
||
Sunflower, prairie*^
|
||
Sunflower, volunteer
|
||
Swinecress
|
||
Thistle, bull
|
||
Thistle, Canada
|
||
Thistle, musk
|
||
Thistle, Russian
|
||
Timothy+
|
||
Torpedograss
|
||
Turnip, wild
|
||
Vaseygrass
|
||
Velvetleaf*^
|
||
Vervain
|
||
Vetch
|
||
Waterhemp, common+
|
||
Waterhemp, tall+
|
||
Wheat, volunteer
|
||
Willowherb, panicle
|
||
Windgrass
|
||
Witchgrass
|
||
Woodsorrel
|
||
Wormwood, biennial+
|
||
Yarrow, common
|
||
+Not for use in California
|
||
^Use rate in California 24 fl. oz./A (0.44 lb. ai)
|
||
*easily controlled species
|
||
|
||
ϯϳ
|
||
|
||
**apply to annual ryegrass prior to 3 inches in height
|
||
***indicates suppression only
|
||
|
||
|
||
STORAGE AND DISPOSAL
|
||
DO NOT contaminate water, food, feed or seed by storage or disposal.
|
||
PESTICIDE STORAGE: DO NOT use or store near heat or open flame. Keep container tightly closed
|
||
and dry in a cool, well ventilated place. Storage temperature must not exceed 125° F. If storage
|
||
temperature of this product is below 32° F, the material must not be pumped until its temperature exceeds
|
||
32° F. Protect against direct sunlight.
|
||
PESTICIDE DISPOSAL: Pesticide wastes are toxic. Improper disposal of excess pesticide, spray
|
||
mixture or rinsate is a violation of Federal law. If these wastes cannot be disposed of by use according
|
||
to label instructions, contact your State Pesticide or Environmental Control Agency or the Hazardous
|
||
Waste Representative at the nearest EPA Regional Office for guidance.
|
||
CONTAINER HANDLING:
|
||
[Note to Reviewer: The following statement will be included on all Final Printed Labels bearing multiple
|
||
Container Handling statements] “NOTE: This product is available in multiple containers. Refer to the
|
||
Net Contents section of this products labeling for the applicable “No refillable” or “Refillable” designation.
|
||
Follow the container handling instructions below that apply to your container type / size.”
|
||
[Note to Reviewer: The bracketed section headers will be included when multiple container types /
|
||
sizes are listed on the label.]
|
||
|
||
[Non-refillable Containers 5 Gallons or Less:] Non-refillable container. DO NOT reuse or refill this
|
||
container. Offer for recycling if available. Triple rinse container (or equivalent) promptly after emptying.
|
||
Triple rinse as follows: Empty the remaining contents into application equipment or a mix tank and drain
|
||
for 10 seconds after the flow begins to drip. Fill the container 1/4 full with water and recap. Shake for 10
|
||
seconds. Pour rinsate into application equipment or a mix tank or store rinsate for later use or disposal.
|
||
Drain for 10 seconds after the flow begins to drip. Repeat this procedure two more times. Then offer for
|
||
recycling or reconditioning, or puncture and dispose of in a sanitary landfill, or by other procedures
|
||
approved by State and local authorities. Plastic containers are also disposable by incineration, or, if
|
||
allo
|
||
wed by State and local authorities, by burning. If burned stay out of smoke.
|
||
|
||
[Non-refillable Containers Larger than 5 Gallons:] Non-refillable container. DO NOT reuse or refill
|
||
this container. Offer for recycling if available. Triple rinse or pressure rinse container (or equivalent)
|
||
promptly after emptying. Triple rinse as follows : Empty the remaining contents into application
|
||
equipment or a mix tank. Fill the container 1/4 full with water. Replace and tighten closures. Tip container
|
||
on its side and roll it back and forth, ensuring at least one complete revolution, for 30 seconds. Stand the
|
||
container on its end and tip it back and forth several times. Turn the container over onto its other end
|
||
and tip it back and forth several times. Empty the rinsate into application equipment or a mix tank or store
|
||
rinsate for later use or disposal. Repeat this procedure two more times. Pressure rinse as follows:
|
||
Empty the remaining contents into application equipment or a mix tank and continue to drain for 10
|
||
seconds after the flow begins to drip. Hold container upside down over application equipment or mix tank
|
||
and continue to drain for 10 seconds after the flow begins to drip. Hold conta iner upside down over
|
||
application equipment or mix tank or collect rinsate for later use or disposal. Insert pressure rinsing nozzle
|
||
in the side of the container, and rinse at about 40 psi for at least 30 seconds. Drain for 10 seconds after
|
||
the flow begins
|
||
to drip.
|
||
|
||
[Refillable Containers Larger than 5 Gallons:] Refillable container. Refill this container with pesticide
|
||
only. DO NOT reuse this container for any other purpose. Cleaning the container before final disposal is
|
||
the responsibility of the person disposing of the container. Cleaning before refilling is the responsibility
|
||
of the refiller. To clean the container before final disposal, empty the remaining contents from this
|
||
container into application equipment or a mix tank. Fill the container a bout 10% full with water and, if
|
||
possible, spray all sides while adding water. If practical, agitate vigorously or recirculate water with the
|
||
pump for two
|
||
minutes. Pour or pump rinsate into application equipment or rinsate collection system. Repeat this rinsing
|
||
procedure two more times. Then offer for recycling if available or puncture and dispose of in a sanitary
|
||
landfill, or by incineration, or by other procedures allowed by state and local authorities.
|
||
|
||
ϯϴ
|
||
|
||
[Refillable Container:] Refill this container with pesticide only. DO NOT reuse this container for any
|
||
other purpose. Close all openings and replace all caps. Contact Nufarm’s Customer Service Department
|
||
at 1-800-345-3330 to arrange for return of the empty refillable container.
|
||
|
||
SEED DISPOSAL: To dispose of out-of-date or otherwise unmarketable seed from plants, which have
|
||
been treated with Cheetah, broadcast and lightly incorporate seed into field soils using disc or other
|
||
suitable implement. Any resulting crop may be destroyed by chemical or mechanical means.
|
||
Alternatively, seed may be destroyed by deep burial, incineration or landfill disposal.
|
||
|
||
|
||
WARRANTY DISCLAIMER
|
||
The directions for use of this product must be followed carefully. TO THE EXTENT CONSISTENT
|
||
WITH APPLICABLE LAW, (1) THE GOODS DELIVERED TO YOU ARE FURNISHED “AS IS” BY
|
||
MANUFACTURER OR SELLER AND (2) MANUFACTURER AND SELLER MAKE NO WARRANTIES,
|
||
GUARANTEES, OR REPRESENTATIONS OF ANY KIND TO BUYER OR USER, EITHER EXPRESS OR
|
||
IMPLIED, OR BY USAGE OF TRADE, STATUTORY OR OTHERWISE, WITH REGARD TO THE
|
||
PRODUCT SOLD, INCLUDING, BUT NOT LIMITED TO MERCHANTABILITY, FITNESS FOR A
|
||
PARTICULAR PURPOSE, USE, OR ELIGIBILITY OF THE PRODUCT FOR ANY PARTICULAR TRADE
|
||
USAGE. UNINTENDED CONSEQUENCES, INCLUDING BUT NOT LIMITED TO INEFFECTIVENESS,
|
||
MAY RESULT BECAUSE OF SUCH FACTORS AS THE PRESENCE OR ABSENCE OF OTHER
|
||
MATERIALS USED IN COMBINATION WITH THE GOODS, OR THE MANNER OF USE OR
|
||
APPLICATION, INCLUDING WEATHER, ALL OF WHICH ARE BEYOND THE CONTROL OF
|
||
MANUFACTURER OR SELLER AND ASSUMED BY BUYER OR USER. THIS WRITING CONTAINS ALL
|
||
OF THE REPRESENTATIONS AND AGREEMENTS BETWEEN BUYER, MANUFACTURER AND
|
||
SELLER, AND NO PERSON OR AGENT OF MANUFACTURER OR SELLER HAS ANY AUTHORITY TO
|
||
MAKE ANY REPRESENTATION OR WARRANTY OR AGREEMENT RELATING IN ANY WAY TO THESE
|
||
GOODS.
|
||
|
||
LIMITATION OF LIABILITY
|
||
TO THE EXTENT CONSISTENT WITH APPLICABLE LAW, IN NO EVENT SHALL MANUFACTURER OR
|
||
SELLER BE LIABLE FOR SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, OR FOR
|
||
DAMAGES IN THEIR NATURE OF PENALTIES RELATING TO THE GOODS SOLD, INCLUDING USE,
|
||
APPLICATION, HANDLING, AND DISPOSAL. TO THE EXTENT CONSISTENT WITH APPLICABLE LAW,
|
||
MANUFACTURER OR SELLER SHALL NOT BE LIABLE TO BUYER OR USER BY WAY OF
|
||
INDEMNIFICATION TO BUYER OR TO CUSTOMERS OF BUYER, IF ANY, OR FOR ANY DAMAGES OR
|
||
SUMS OF MONEY, CLAIMS OR DEMANDS WHATSOEVER, RESULTING FROM OR BY REASON OF,
|
||
OR RISING OUT OF THE MISUSE, OR FAILURE TO FOLLOW LABEL WARNINGS OR INSTRUCTIONS
|
||
FOR USE, OF THE GOODS SOLD BY MANUFACTURER OR SELLER TO BUYER. ALL SUCH RISKS
|
||
SHALL BE ASSUMED BY THE BUYER, USER, OR ITS CUSTOMERS. TO THE EXTENT CONSISTENT
|
||
WITH APPLICABLE LAW, BUYER'S OR USER'S EXCLUSIVE REMEDY, AND MANUFACTURER'S OR
|
||
SELLER'S TOTAL LIABILITY SHALL BE FOR DAMAGES NOT EXCEEDING THE COST OF THE
|
||
PRODUCT.
|
||
|
||
If you DO NOT agree with or DO NOT accept any of directions for use, the warranty disclaimers, or
|
||
limitations on liability, DO NOT use the product, and return it unopened to the Seller, and the
|
||
purchase price will be refunded.
|
||
|
||
(RVXXXXXX)
|
||
Cheetah is a registered trademark of Nufarm Americas Inc.
|
||
|
||
ϯϵ
|
||
|
||
|
||
|
||
|
||
Optional Marketing Claims:
|
||
|
||
Nufarm Grow a better tomorrow.
|
||
Grow a better tomorrow.
|
||
|
||
|
||
[Note to reviewer: Any text found in brackets “[“ “]” is optional on container label.]
|
||
[Note to reviewer: State restrictions will not be found on the container label if the product is not registered
|
||
in that associated state.]
|
||
[Note to reviewer: Making the product more restrictive then Federally accepted, incorporating the optional
|
||
statement “Not for use in California.” may be included on the container label for any use, weed or crop as
|
||
determined to be necessary to procure CADPR registration.]
|