crop-chem-docs/corpus/epa_ppls/19713-678.md

# DREXEL DICAMBA 2,4 DE-AMINE 

- EPA Reg No: **19713-678**
- Registrant: DREXEL CHEMICAL COMPANY
- Signal word: Danger
- Active ingredients: Dicamba, dimethylamine salt (12.4%); 2,4-D, dimethylamine salt (35.7%)
- Label accepted: 2016-05-06
- Source PDF: https://www3.epa.gov/pesticides/chem_search/ppls/019713-00678-20160506.pdf

---
UNITED STATES ENVIRONMENTAL PROTECTION AGENCY 
 WASHINGTON, DC 20460 
 
 
 
Notification Label Acceptable v.20150904 
OFFICE OF CHEMICAL SAFETY 
AND POLLUTION PREVENTION 
May 6, 2016 
 
Luz G. Chan 
Registration Manager 
Drexel Chemical Company 
PO Box 13327 
Memphis, TN 38113 
 
Subject: Notification per PRN 98-10 – Change of Primary Brand Name 
 Product Name: DREXEL DICAMBA 2,4-DE-AMINE 
 EPA Registration Number: 19713-678 
 Application Date: 4/28/2016 
 Decision Number: 516852 
 
Dear Ms. Chan: 
 
The Agency is in receipt of your Application for Pesticide Notification under Pesticide Registration 
Notice (PRN) 98-10 for the above referenced product. The Registration Division (RD) has conducted a 
review of this request for its applicability under PRN 98-10 and finds that the action requested falls within 
the scope of PRN 98-10. 
 
The label submitted with the application has been stamped “Notification” and will be placed in our 
records. The primary brand name DREXEL DICAMBA 2,4-DE-AMINE has been added to the product 
record. 
 
Should you wish to add/retain a reference to the company’s website on your label, then please be aware 
that the website becomes labeling under the Federal Insecticide Fungicide and Rodenticide Act and is 
subject to review by the Agency. If the website is false or misleading, the product would be misbranded 
and unlawful to sell or distribute under FIFRA section 12(a)(1)(E). 40 CFR 156.10(a)(5) list examples of 
statements EPA may consider false or misleading. In addition, regardless of whether a website is 
referenced on your product’s label, claims made on the website may not substantially differ from those 
claims approved through the registration process. Therefore, should the Agency find or if it is brought to 
our attention that a website contains false or misleading statements or claims substantially differing from 
the EPA approved registration, the website will be referred to the EPA’s Office of Enforcement and 
Compliance. 
 
If you have any questions, you may contact Sarah Meadows at 703-347-0505 or via email at 
meadows.sarah@epa.gov. 
 
 
Sincerely, 
 
Kathryn Montague, Product Manager 23 
Herbicide Branch 
Registration Division (7505P) 
Office of Pesticide Programs

Page1of19


 



For use on Conservation Reserve Program Land, Fallow Systems (Between Crop Applications), General 
Farmstead, Sorghum, Grass (Hay or Silage), Pastures, Rangeland, Sugarcane and Wheat
ACTIVE INGREDIENTS*: 
 Dimethylamine salt of Dicamba (3,6-dichloro-o-anisic acid)..................................................................... 12.4% 
 Dimethylamine salt of 2,4-dichlorophenoxyacetic acid**.......................................................................... 35.7% 
OTHER INGREDIENTS:................................................................................................................................ 51.9% 
 TOTAL:.................................................................................................................................................. 100.0%
 * This product contains 10.3% Dicamba or 1 pound per gallon (120 grams per liter) and 29.6% 2,4-D or 2.87 pounds per gallon 
(344 grams per liter). 
** Isomer specific by AOAC method 978.05, 15th Edition.
KEEP OUT OF REACH OF CHILDREN 
DANGER / PELIGRO 
Si usted no entiende la etiqueta, busque a alguien para que se la explique a usted en detalle. (If you do not understand the 
label, find someone to explain it to you in detail.)
See FIRST AID Below 
Shake Well Before Using (Recirculate Contents Before Use) 
EPA Reg. No. 19713-678 
EPA Est. No. 19713-XX-X Net Content: ______(Gals) (_____L) 
FIRST AID
IF IN EYES: 
• Hold eye open and rinse slowly and gently with water for 15 to 20 minutes. 
• Remove contact lenses, if present, after the first 5 minutes, then continue rinsing eye. 
• Call a poison control center or doctor for treatment advice.
IF SWALLOWED: 
• Call a poison control center or doctor immediately for treatment advice. 
• Have person sip a glass of water if able to swallow. 
• Do not induce vomiting unless told to do so by a poison control center or doctor. 
• Do not give anything to an unconscious person. 
IF ON SKIN OR CLOTHING: 
• Take off contaminated clothing. 
• Rinse skin immediately with plenty of water for 15 to 20 minutes. 
• Call a poison control center or doctor for treatment advice.
IF INHALED: 
• Move person to fresh air. 
• If person is not breathing, call 911 or an ambulance, then give artificial respiration, preferably mouth-to-
mouth, if possible. 
• Call a poison control center or doctor for further treatment advice.
Have the product container or label with you when calling a poison control center or doctor or going for treatment. 
You may also call CHEMTREC at 800-424-9300 for emergency. 
 678SP-0416* 
GROUP 4 HERBICIDES
Dicamba 2,4 De-AmineTM
Herbicide
19713-678
05/06/2016


Page2of19

PRECAUTIONARY STATEMENTS 
Hazards To Humans And Domestic Animals 
DANGER: Corrosive. Causes irreversible eye damage. Do not get in eyes or on clothing. Harmful if swallowed, 
inhaled, or absorbed through skin. Avoid contact with skin. Avoid breathing spray mist. 
PERSONAL PROTECTIVE EQUIPMENT (PPE)
Some materials that are chemical-resistant to this product are any waterproof material. 
All mixers, loaders, applicators, flaggers and other handlers must wear: Long-sleeved shirt and long 
pants, shoes and socks, chemical-resistant gloves, protective eyewear (goggles or face shield) and • chemical-
resistant apron when mixing or loading, cleaning up spills or equipment or otherwise exposed to the concentrate
See “ENGINEERING CONTROLS” for additional requirements. 
Discard clothing and other absorbent materials that have been drenched or heavily contaminated with this 
product’s concentrate. Do not re-use them. 
Follow the manufacturer’s instructions for cleaning and maintaining PPE. If no such instructions for washables 
exist, use detergent and hot water. Keep and wash PPE separately from other laundry. After each day of use, 
clothing or PPE must not be reused until it has been cleaned. 
ENGINEERING CONTROLS 
When handlers use closed systems, enclosed cabs, or aircraft in a manner that meets the requirements listed 
in the Worker Protection Standard (WPS) for agricultural pesticides [40 CFR 170.240(d)(4-6)], the handler PPE 
requirements may be reduced or modified as specified in the WPS. Pilots must use an enclosed cockpit which 
meets the requirements listed in the WPS for agricultural pesticides [40 CFR 170.240(d)(6)].
USER SAFETY RECOMMENDATIONS 
Users should: 1) Wash hands thoroughly with soap and water after handling and before eating, drinking, 
chewing gum, using tobacco or using the toilet. 2) Remove clothing/PPE immediately if pesticide gets inside. 
Then wash thoroughly and put on clean clothing. 3) Remove PPE immediately after handling this product. 
Wash the outside of gloves before removing. As soon as possible, wash thoroughly and change into clean 
clothing. 
ENVIRONMENTAL HAZARDS 
This pesticide may be toxic to fish and aquatic invertebrates. Do not apply directly to water, to areas where surface 
water is present, or to intertidal areas below the mean high water mark. Drift and runoff may be hazardous to 
aquatic organisms in water adjacent to treated areas. Drift or runoff may adversely affect non-target plants. Do not 
contaminate water when disposing of equipment washwaters or rinsate. 
This has properties and characteristics associated with chemicals detected in groundwater. The use of this 
chemical in areas where soils are pe rmeable, particularly where the water table is shallow, may result in 
groundwater contamination. Application around a cistern or well may result in contamination of drinking water or 
groundwater. 
Most cases of groundwater contamination involving phenoxy herbicides such as 2,4-D have been associated with 
mixing/loading and disposal sites. Precaution should be exercised when handling 2,4-D pesticides at such sites to 
prevent contamination of groundwater supplies. Use of closed systems for mixing or transferring this pesticide will 
reduce the probability of spills. Placement of the mixing/loading equipment on an impervious pad to contain spills 
will help prevent groundwater contamination. 
DIRECTIONS FOR USE 
It is a violation of Federal law to use this product in a manner inconsistent with is labeling. Do not apply this product 
in a way that will contact workers or other persons, either directly or through drift. Only protected handlers may be 
in the area during application. For any requirements specific to your state or tribe, consult the agency responsible 
for pesticide regulation.


Page3of19

AGRICULTURAL USE REQUIREMENTS 
Use this product only in accordance with its labeling and with the Worker Protection Standard, 40 CFR part 
170. This standard contains requirements for the protection of agricultural workers on farms, forests, 
nurseries, and greenhouses, and handlers of agricultural pesticides. It contains requirements for training, 
decontamination, notification, and emergency assistance. It also contains specific instructions and 
exceptions pertaining to the statements on this label about Personal Protective Equipment (PPE), and 
Restricted Entry Interval. The requirements in this box only apply to uses of this product that are covered by 
the Worker Protection Standard. 
Do not enter or allow worker entry into treated areas during the Restricted Entry Interval (REI) of 48 hours.
PPE required for early entry to treated areas that is permitted under the Worker Protection Standard and that 
involves contact with anything that has been treated, such as plants, soil, or water, is: Coveralls worn over 
short-sleeved shirt and short pants, chemical-resistant gloves made of any waterproof material, chemical-
resistant footwear plus socks, chemical-resistant headgear for overhead exposure and protective eyewear.
NON-AGRICULTURAL USE REQUIREMENTS
The requirements in this box apply to uses of this product that are NOT within the scope of the Worker 
Protection Standard for Agricultural Pesticides (40 CFR Part 170). The WPS applies when this product is 
used to produce agricultural plants on farms, forests, nurseries, or greenhouses. 
Do not enter or allow people (or pets) to enter the treated area until sprays have dried.
PRODUCT INFORMATION
DICAMBA 2,4 DE-AMINE herbicide is a selective post-emergence herbicide for controlling a wide spectrum of 
annual, biennial, and perennial broadleaf weeds and brush in grass forages and selected row crops. 
Mode of Action
This product contains two active ingredients: Dicamba and 2,4-D. This product is readily absorbed by plants 
through shoot and root uptake and translocates throughout the plant’s system and accumulates in areas of active 
growth. This product interferes with the plant’s growth hormones (auxins) resulting in death of many broadleaf 
weeds.
CLEANING SPRAY EQUIPMENT
Clean application equipment thoroughly by using a strong detergent or commercial sprayer cleaner according to 
the manufacturer’s directions and then triple rinse the equipment before and after applying this product.
SPRAY DRIFT MANAGEMENT
A variety of factors including weather conditions (e.g., wind directions, wind speed, temperature, relative humidity) 
and method of application (e.g., ground, aerial, airblast, chemigation) can influence pesticide drift. The applicator 
must evaluate all factors and make appropriate adjustments when applying this product. 
Droplet Size
When applying sprays that contain 2,4-D as the sole active ingredient or when applying sprays that contain 2,4-D 
mixed with active ingredients that require a coarse or coarser spray, apply only as a coarse or coarser spray (ASAE 
standard 572) or a volume mean diameter of 385 microns or greater for spinning atomizer nozzles. 
When applying sprays that contain 2,4-D mixed with other active ingredients that require a medium or more fine 
spray, apply only as a medium or coarser spray (ASAE standard 572) or a volume mean diameter of 300 microns 
or greater for spinning atomizer nozzles. 
Wind Speed
Do not apply at wind speeds greater than 15 mph. Only apply this product if the wind direction favors on-target 
deposition and there are not sensitive areas (including, but limited to, residential areas, bodies of water, known 
habitat for non-target species, non-target crops) within 250 feet downwind. If applying a medium spray, leave one 
swath unsprayed at the downwind edge of the treated field.


Page4of19

Temperature Inversions
If applying at wind speeds less than 3 mph, the applicator must determine if: a) conditions of temperature inversion 
exist, or b) stable atmospheric conditions exist at or below nozzle height. Do not make applications into areas of 
temperature inversions or stable atmospheric conditions. 
Susceptible Plants
Do not apply under circumstances where spray drift may occur to food, forage, or other plantings that might be 
damaged or crops thereof rendered unfit for sale, use or consumption. This product may cause injury to desirable 
trees and plants when contacting their roots, stem or foliage. Susceptible crops include, but are not limited to, 
Cotton, Okra, Flowers, Grapes (in growing stage), Fruit trees (foliage), Soybeans (vegetative stage), Ornamentals, 
Sunflowers, Tomatoes, Beans, Peas, Potatoes and othe r Vegetables, and Tobacco. These plants are most 
sensitive to this product during their development or growing stage. Small amounts of spray drift that might not be 
visible may injure susceptible broadleaf plants. 
Avoid making applications when spray particles may be carried by air currents to areas where sensitive crops and 
plants are growing. Do not spray near sensitive plants if it is gusty or in excess of 5 mph and moving in the direction 
of nearby sensitive crops or if a temperature inversion exists. However, always make applications when there is 
some air movement to determine the direction and distance of possible spray drift. Coarse sprays are less likely 
to drift out of the target area than fine sprays. Agriculturally approved drift reducing additives may be used. 
Do not use aerial equipment to apply this product when sensitive crops and plants are growing in the vicinity of the 
area to be treated. 
Other State and Local Requirements
Applicators must follow all state and local pesticide drift requirements regarding applications of 2,4-D herbicides. 
Where states have more stringent regulations, they must be observed.
Equipment
All aerial and ground application equipment must be properly maintained and calibrated using appropriate carriers 
or surrogates. 
For Aerial Application:
The boom length must not exceed 75% of the wingspan or 90% of the rotor blade diameter. 
Release spray at the lowest height consistent with efficacy and flight safety. Do not release spray at a height 
greater than 10 feet above the crop canopy unless a greater height is required for aircraft safety. This requirement 
does not apply to forestry or rights-of-way applications.
When applications are made with crosswind, the swath will be displaced downwind. The applicator must 
compensate for this by adjusting the path of the aircraft upwind. 
For Ground Boom Application:
Do not apply with a nozzle height greater than 4 feet above the crop canopy. 
APPLICATION INSTRUCTIONS
Apply this product at the rates and growth stages listed in Tables 1 and 2 unless instructed differently by 
“FOOD/FEED CROP SPECIFIC INFORMATION” or “NON-FOOD/FEED USE” sections. Applications can be made 
to actively growing weeds as aerial, broadcast, band, or spot spray applications. This product may be applied using 
water or sprayable fluid fertilizer as a carrier. Sprayable fluid fertilizer may be used as the carrier in pre-plant or 
pre-emergence uses for all crops fisted on this label. Post-emergence uses with sprayable fluid fertilizer may be 
made on Pasture, Hayland or Wheat crops only. The most effective application rate and timing varies based on 
the target weed species (refer to Table 1). In mixed populations of weeds, the correct rate is determined by the 
weed species requiring the highest rate. Delaying application permits weeds to exceed the maximum size stated 
and will prevent adequate control. 
Do not treat areas where either possible downward movement into the soil or surface washing may cause contact 
of this product with the roots of desirable plants such as trees and shrubs. 
Irrigation
In irrigated areas, it may be necessary to irrigate before treatment to ensure active weed growth.
Spray Coverage
Weeds must be thoroughly covered with spray. Dense leaf canopies shelter smaller weeds and can prevent 
adequate spray coverage.


Page5of19

Aerial Application Methods and Equipment
Water Volume: Use 3 to 10 gallons of water per acre. Use the higher spray volume when treating dense or tall 
vegetation.
Application Equipment: Select nozzles designed to produce minimal amounts of fine spray particles. Make 
applications at the lowest safe height to reduce the exposure of spray droplets to evaporation and wind. The 
applicator must follow the most restrictive use precautions to avoid drift hazards, including those found in this 
labeling (see “SPRAY DRIFT MANAGEMENT” section for specific requirements), as well as applicable state and 
local regulations and ordinances. Do not use aerial equipment if spray particles of this product can be carried by 
the wind into areas where sensitive crops or plants are growing or when temperature inversions exist. 
Ground Application (Banding)
When applying this product by banding, determine the amount of herbicide and water volume needed using the 
following formula: 
Band width in inches x Broadcast rate = Banding herbicide 
Row width in inches per acre rate per acre 
Band width in inches x Broadcast = Banding water 
Row width in inches volume per acre volume per acre 
Ground Application (Broadcast)
Water Volume: Use 5 to 40 gallons of spray solution per acre for optimal performance. Use the higher spray 
volume when treating dense or tall vegetation. 
Application Equipment: Select nozzles designed to produce minimal amounts of fine spray particles. Spray with 
nozzles as close to the weeds as is practical for good weed coverage. The applicator must follow the most 
restrictive use precautions to avoid drift hazards, including those found in this labeling (see “SPRAY DRIFT 
MANAGEMENT” section for specific requirements) as well as applicable state and local regulations and 
ordinances.


Page6of19

Table 1. Application Rate and Timing — Annual Weeds
Weeds Controlled 
(including ALS and 
triazine resistant)
 Rate of This Product Per Acre (According to Weed Growth Stage)
0.5 pint 1 pint 1.5 pints 2 pints 3 pints 4 pints
Beebalm, Spotted - - - Pre-bloom Post-bloom - 
Broomweed 1 to 3” 3” branching - Branching - After branching 
Buckwheat, Wild - 1 to 6” - - - - 
Buffalo bur - - - 1 to 6” - After flowering 
Burdock - Pre-flower - - - - 
Butter cup - Pre-flower - Early bloom Late bloom - 
Chickweed, Common - Seedling 1 to 3” - - - 
Cockle, Cow - < 3” - - - - 
Cocklebur, Common - 1 to 6” 6 to 12” 12 to 18” - - 
Coreopsis, Plain - 1 to 6” - - - - 
Croton, Wooly 1 to 4” 4 to 12” 12 to 30” - - - 
Devils claw - - - < 8” -- - 
Dogfennel - - - 10 to 15” - - 
Evening primrose - < 2” - 2 to 6” - - 
Flax - < 2” - - - - 
Fleabane, Annual - 1 to 4” 4 to 8” 8” - - 
Flixweed - < 3” - - - - 
Henbit - - Pre-flower - Flower - 
Knotweed spp. - < 3” runners - > 3” runners - Actively growing 
Kochia - 1 to 6” 6 to 10” 10 to 20” - Actively growing 
Lambsquarters, Common - 1 to 6” 6 to 10” 10 to 20” - Actively growing 
Mallow, Common - < 3” - - - - 
Morningglory, Ivyleaf - Pre-flower - - - - 
Morningglory, Tall - Pre-flower - Post-flower - - 
Mustards, Annual - Rosette - Early bolt - - 
Mustards, Tansy - < 3” - - - - 
Pennycress, Field - - - Rosette - - 
Pepperweed, Virginia - - 1 to 3” 3 to 6” After branching - 
Pigweed, Prostate - < 3” - - - - 
Pigweed, Redroot - < 3” 3 to 10” - - - 
Pigweed, Smooth - < 3” - - - - 
Pigweed, Tumble - < 3” - Mature - - 
Poorjoe - Prior to flower - - - Actively growing 
Purslane, Common - < 3” 3 to 8” - - - 
Ragweed, Common - - - > 10” - - 
Western, Lanceleaf 1 to 3” 3 to 6” 6 to 10” Actively growing - - 
Sedge* - - - - - - 
Shepherdspurse - Rosette - - - - 
Smartweed, Pennsylvania - 4” - - 4 to 12” - 
Sneezeweed, Bitter - 1 to 4” Prior to flower Flower - - 
Sowthistle - Rosette - Bolting - - 
Sunflower - 1 to 3” 3 to 6” 6 to 24” - - 
Thistle, Russian - - - Rosette - - 
Velvetleaf - < 6” 6 to 20” > 20” - - 
*For use in Nonfood/Feed crop only. Adding crop oil concentrate has shown to improve performance on actively growing annual sedg e.


Page7of19

Table 2. Application Rate and Timing — Biennial and Perennial Weeds
Weeds 
Controlled 
Rate of This Product Per Acre (According to Weed Growth Stage)
0.5 pint 1 pint 1.5 pints 2 pints 3 pints 4 to 6 pints
Bindweed, Field - - - - - Actively growing 
Bittercress - 2 to 3” - - - - 
Buckeye species1 - - - - Full leaf - 
Bullnettle2 - - - Flower - - 
Chicory - - - - Early bolting - 
Clover, Bur - - Pre-flower - - - 
Dandelion, Common - Rosette - Bolting - - 
Dewberry, Southern1 - - - - - Spring or fall 
Dock, Curly - - Prior to bolting - After bolting - 
Elderberry2 - - - - - Actively growing 
Goldenrod, Missouri - - - 3 to 15” Flower - 
Goldenweed, Common - - - - - Actively growing 
Groundsel Texas - Rosette Post-bolting - - - 
Honeysuckle, Hairy - - - - Spring or Fall - 
Horsenettle, Carolina1 - - - - - Flower or berry 
Ivy, Poison - - - After bloom - - 
Knapweed, Black2 - - - - - Actively growing 
Knapweed, Russian2 - - - - - Actively growing 
Knapweed, Spotted - - - - - Actively growing 
Marshelder - - - < 12” <12” Pre-bloom - 
Mesquite - - - - - 45 to 90 days after 
bud break 
Milkweed antelopehorn1 - - - Pre-flower - Flower 
Nightshade, Silverleaf1 - - - Full flower - - 
Nightshade, Black1 - - - Full flower - Actively growing 
Persimmon, Eastern³ - - - - - Actively growing 
Prickly lettuce - - - Rosette - Actively growing 
Rabbitbrush² - - - - - - 
Ragwort, Tansy - - - Rosette - Actively growing 
Redvine² - - - - - Actively growing 
Sagebrush, Fringed² - - - - - Actively growing 
Smartweed - - - - - - 
Sorrel, Red - - Rosette Bolting Flower Actively growing 
Sowthistle² - - - - - Actively growing 
Spurge, Leafy² - - - - - Full leaf 
Tallow tree, Chinese4 - - - - - - 
Thistle, Bull - - Rosette Bolting - Actively growing 
Thistle, Canada² - - - - - - 
Thistle, Musk - - - Rosette/ 
Bolting 
- - 
Thistle, Plumless - - Rosette Bolting - - 
Vetch, Hairy - 1 to 4” 4 to 8” 8” Full flower - - 
Yankeeweed - - - 10 to 18” - - 
Yellow starthistle¹ - - - - - - 
¹ May require repeat applications. 
² Specified rate will provide top growth suppression only. 
³ For improved root kill or woody species such as Mesquite and Eastern persimmon, spray 4 pints of this product per acre 
 each year for 3 consecutive years. For increased control of weeds such as Blackberry and Dewberry, this product may be tank-mixed
with Ally
® herbicide (0.1 to 0.2 oz. per acre), if labeled for the use site. 
4 Under dense populations, a second application may be needed for the following growing season.


Page8of19

Spot or Small Area Application
This product may be applied to individual clumps or small areas of undesirable vegetation using handgun or similar 
types of application equipment. Apply diluted sprays to allow complete wetting (up to runoff) of foliage and stems. 
For knapsack, or other small capacity sprayers, prepare a solution of this product in water according to Table 3 
(assuming that the spot treatment rate equates to 60 gallons per acre on the broadcast basis.) Adding a surfactant 
(0.5% by volume) can help improve control. For example, 5 gallons (40 pts. or 640 fl. ozs.) of herbicide solution 
would require 0.2 pint (3.2 fl. oz.) of surfactant. 
Application Equipment: Select nozzles designed to produce minimal amounts of fine spray particles. Spray with 
nozzles as close to the weeds as is practical for good weed coverage.
Table 3. Knapsack Sprayer Dilution Instructions 
Sprayer Capacity (Gals. of Water) Amount of This Product to Add to the Spray Tank
1 gal. 1 fl. oz.* 
3 gals. 3 fl. ozs. 
5 gals. 5 fl. ozs. 
*1 fl. oz. = 2 tbsp.
ADDITIVES 
To improve burn down of emerged weeds, surfactants and/or low use rate of liquid fertilizers (28-0-0, 32-0-0), or 
crop oil concentrate may be used with this product or tank-mixes after the weeds have emerged. Crop oil 
concentrate is for non-food/feed purposes only. Do not apply tank-mixes that include ammonium sulfate or crop 
oil concentrate to any food/feed crop use listed on this label. For food/feed crop uses, do not use liquid fertilizers 
that contain ammonium sulfate (AMS) as a source of nitrogen as tolerances in commodities derived from the crop 
may contain residues that exceed established tolerances. Consult your local representative for recommendations 
for your area. For additional information, see compatibility test for mix components. 
Oil Concentrate 
A crop oil concentrate must contain either a petroleum or vegetable oil base and must meet all of the following 
criteria: 
• Be non-phytotoxic. 
• Contains only EPA exempt ingredients. 
• Provide good mixing quality in the jar test, and 
• Be successful in local experience. 
The exact composition of suitable products will vary; however, vegetable and petroleum oil concentrates should 
contain emulsifiers to provide good mixing quality. Highly refined vegetable oils have proven more satisfactory 
than unrefined vegetable oils. For additional information, see compatibility test for mix components. 
Adjuvants containing crop oil concentrates may be used for pre-plant, pre-emergence and between cropping 
applications. Do not use crop oil concentrate for post-emergence applications in food/feed crops (i.e., Sorghum, 
Grass (hay or silage), Pastures, Rangeland, Sugarcane and Wheat). 
Nitrogen Source
• Sprayable liquid fertilizers: Use one quart of sprayable liquid fertilizers (28-0-0, 32-0-0) per acre. Do not use brass 
or aluminum nozzles when spraying fertilizers. 
Non-ionic Surfactant
The standard label recommendation is 2 to 4 pints of an 80% active non-ionic spray surfactant per 100 gallons of 
water. For certain weeds, use a higher spray surfactant rate.


Page9of19

Table 4. Additive Rate Per Acre
Additive Rate Per Acre
Non-ionic surfactant 2 to 4 pints per 100 gallons 
Sprayable liquid fertilizer (28-0-0, 32-0-0) 2 to 4 quarts 
Crop Oil Concentrate 1 quart* 
*See manufacturer’s label for specific rate directions. 
TANK-MIXING INFORMATION
Tank-Mix Partners/Components
The following products may be tank-mixed with this product according to the specific tank-mixing instructions in 
this label and respective product labels. 
• Aim (Carfentrazone-ethyl) 
• Ally (Metsulfuron-methyl) 
• Amber (Triasulfuron) 
• Asulox (Asulam) 
• Products containing Atrazine 
• Banvel (Dicamba) 
• Basagran (Bentazon) 
• Bronate (Bromoxynil + MCPA) 
• Buctril (Bromoxynil)
• Canvas (Thifensulfuron + Metsulfuron + Tribenuron) 
• Clarity (Dicamba) 
• Curtail (Clorpyralid + 2,4-D) 
• Cyclone (Paraquat) 
• Products containing 2,4-D 
• Dakota (Fenoxaprop-p-ethyl + MCPA) 
• Distinct (Diflufenzopyr)
• Evik (Ametryn) 
• Express (Thifensufuron + Tribenuron-methyl) 
• Fallowmaster (Glyphosate + Dicamba) 
• Finesse (Chlorsulfuron + Metsulfuron-methyl) 
• Glean (Chlorsulfuron) 
• Gramoxone (Paraquat) 
• Harmony Extra (Thifensulfuron + Tribenuron-methyl) 
• Karmex (Diuron) 
• Kerb (pronamide) 
• Laddok S-12 (Bentazon + Atrazine) 
• Landmaster (Glyphosate + 2,4-D) 
• Lexone (Metribuzin) 
• Products containing MCPA 
• Paramount (Quinclorac) 
• Peak (Prosulfuron) 
• Permit (Halosulfuron-methyl) 
• Rave (Dicamba + Triasulfuron) 
• Roundup Ultra (Glyphosate) 
• Sencor (Metribuzin) 
• Sinbar (Terbacil) 
• Stinger (Clopyralid) 
• Tiller (Fenoxaprop-p-ethyl + 2,4-D + MCPA) 
• Tordon (Picloram) 
• Touchdown (Glyphosate)


Page10of19

See “FOOD/FEED CROP-SPECIFIC INFORMATION” section for more details. Read and follow the applicable 
“RESTRICTIONS AND LIMITATIONS” and “DIRECTIONS FOR USE” on all products involved in tank-mixing. The 
most restrictive labeling applies to tank-mixes. 
It is the pesticide user’s responsibility to ensure that all products are registered for the intended use. Read 
and follow the applicable restrictions and limitations and directions for use on all product labels involved 
in tank mixing. Users must follow the most restrictive directions for use and precautionary statements of 
each product in the tank mixture. 
Physical incompatibility, reduced weed control or crop injury may result from mixing this product with other 
pesticides (fungicides, herbicides, insecticides or miticides), additives or fertilizers. Manufacturer does not 
recommend using tank-mixes other than those listed above on this labeling. Local agricultural authorities may be 
a source of information when using other than the Manufacturer recommended tank-mixes. Add components in 
the sequence indicated in the “Mixing Order” using 2 teaspoons for each pound or 1 teaspoon for each pint of label 
specified rate per acre. Always cap the jar and invert 10 cycles between component additions. 
When the components have all been added to the jar, let the solution stand for 15 minutes. Evaluate the solution 
for uniformity and stability. The spray solution should not have free oil on the surface, nor fine particles that 
precipitate to the bottom, nor thick (clabbered) texture. If the spray solution is not compatible, repeat the 
compatibility test with the addition of a suitable compatibility agent. If the solution is then compatible, use the 
compatibility agent as directed on its label. If the solution is still incompatible, do not mix the ingredients in the 
same tank. 
Mixing Order
If an inductor is used, rinse it thoroughly after each component has been added. Maintain constant agitation during 
application. 
1) Water* – Begin by agitating a thoroughly clean sprayer tank half full of clean water. 
2) Agitation – Maintain constant agitation throughout mixing and application.
3) Products in PVA bags – Place any product contained in water-soluble PVA bags into the mixing tank. Wait 
until all water-soluble PVA bags have fully dissolved and the product is evenly mixed in the spray tank before 
continuing. 
4) Water-dispersible products (such as dry flowables, wettable powders, suspension concentrates or suspo-
emulsions). 
5) Water-soluble products (such as this product). 
6) Emulsifiable concentrates (such as oil concentrate when applicable). 
7) Water-soluble additives [such as liquid fertilizers (28-0-0, 32-0-0) when applicable]. 
8) Remaining quantity of water.
*If sprayable fluid fertilizer is used as the carrier, this product must be diluted with a minimum of 5 parts water to 1 
part this product. Then add 0.25 to 0.5% volume/volume of a non-ionic surfactant to the dilution before adding it 
to the sprayable fluid fertilizer to reduce the concern for compatibility problems with this mix. Always perform the 
compatibility test before mixing into the spray tank. Also, when using a sprayable fluid fertilizer as the carrier, any 
product contained in PVA bags must first be completely dissolved in water before the contents can be added to 
the fertilizer mix.
RESTRICTIONS AND LIMITATIONS
• Maximum seasonal use rate: Refer to Table 5.
• Pre-harvest Interval (PHI): Refer to “FOOD/FEED CROP-SPECIFIC INFORMATION” section. 
Crop-Specific Information:
• Restricted Entry Interval (REI): 48 hours 
Crop Rotational Restrictions:
The interval between application and planting rotational crops is given below. Always exclude counting days when 
the ground is frozen. Planting at intervals less than specified below may result in crop injury. Moisture is essential 
for the degradation of this herbicide in soil. If dry weather prevails, use cultivation to allow herbicide contact with 
moist soil. 
–Planting/replanting restrictions for applications of 5.6 pints per acre or less of this product: No rotational 
cropping restrictions apply at 120 days or more following application. Additionally, for annual crop uses in this label


Page11of19

including Sorghum, follow the pre-plant use directions in the “FOOD/FEED CROP-SPECIFIC INFORMATION” 
section. 
For Barley, Oat, Wheat and other grass seedlings, the interval between application and planting is 10 days per 
pint per acre. 
–Planting/replanting restrictions for applications of more than 5.6 pints and up to 8 pints of this product 
per acre: Corn, Sorghum, Cotton (east of the Rocky Mountains) and all other crops grown in areas with 30 inches 
or more of annual rainfall may be planted 120 days or more after application. Barley, Oat, Wheat, and other grass 
seedlings, may be planted if the interval from application to planting is 10 days per pint per acre east of the 
Mississippi River and 15 days per pint per acre west of the Mississippi River. For all other crops in areas with less 
than 30 inches of annual rainfall, the interval between application and planting is 180 days or more. 
• Rainfast period: Rainfall or irrigation occurring within 4 hours after post-emergence applications may reduce the 
effectiveness of this product. 
xStress: Do not apply to crops under stress such as stress due to lack of moisture, hail damage, flooding, herbicide 
injury, mechanical injury or widely fluctuating temperatures, as unsatisfactory control may result. 
• Do not apply to crops that show injury (leaf phytotoxicity or plant stunting) produced by any other prior herbicide 
applications, because this injury may be enhanced or prolonged. 
• Do not apply through any type of irrigation equipment. Do not contaminate irrigation ditches or water used for 
domestic purposes. 
• This product cannot be used to formulate or reformulate any other pesticide product. 
Table 5. Crop-Specific Restrictions and Limitations 
Crop
Maximum Rate Per 
Acre Per 
Application
Maximum Rate 
Per Acre Per 
Season
Livestock 
Grazing or 
Feeding*
Aircraft 
Application
Between Crop 
Applications**
5.6 pts. 8 pts. Yes Yes 
Pasture, Hay Silage 4 pts. 8 pts. Yes Yes 
Sugarcane 5.6 pts. 11.2 pts. Yes Yes 
Sorghum 2.8 pts. 2.8 pts. Yes Yes 
Wheat 2 pts. 3.33 pts. Yes Yes 
 * Refer to “FOOD/FEED CROP-SPECIFIC INFORMATION” section for grazing and feeding restrictions. 
** Only labeled crops can be planted within 30 days of application. Limited to 2 applications per year. Minimum of 30 
days between application
FOOD/FEED CROP-SPECIFIC INFORMATION 
FOOD/FEED CROP USES
This product can be used on the following: 
*Conservation Reserve Program Land 
*Fallow Systems (Between Crop Applications) 
Grain Sorghum 
Grass (Hay or Silage) 
Pastures
Rangeland 
Sugarcane 
Wheat
See sections “RESTRICTIONS AND LIMITATIONS” and “APPLICATION INSTRUCTIONS”.
* *These sites are considered to be Food/Feed uses only when harvested, grazed or foraged. Otherwise, they are considered to be Non-
food/Feed uses. 
PASTURES, RANGELAND AND GRASS (Hay, Silage) 
This product is for use on pastures (including pasture grown for hay), rangeland and grass grown for hay or silage. 
If grass is to be cut for hay, Agricultural Use Restrictions for the Worker Protection Standard are applicable. 
Refer to Tables 1 and 2 for rate selection based on targeted weed or brush species. Some weed species will 
require tank-mixes for adequate control.


Page12of19

For susceptible annual and biennial broadleaf weeds, do not exceed 2.8 pints of this product per acre per 
application. For moderately susceptible biennial and perennial broadleaf weeds and woody plants, do not exceed 
5.6 pints per acre per application. 
Retreatment may be made as needed (maximum of 2 applications per year). Allow a minimum of 30 days between 
applications. Do not exceed a total of 8 pints of this product per treated acre during a growing season. 
Rates above 4 pints of this product per acre per application are for spot treatments only. Do not exceed 5.6 pints 
of this product per acre per application or a maximum of 11.2 pints per acre per year for spot treatments. Minimum 
of 30 days between application. Maximum of 2 applications per year. 
Uses described in this section also pertain to small grains (such as Barley, Corn, Forage sorghum, Oats, Rye, 
Sudangrass or Wheat) grown for pasture, hay and silage only. Newly seeded areas, including small grains grown 
for pasture or hay, may be injured if rates greater than 2 pints of this product per acre are applied. 
In newly established hybrid Bermudagrass, Pangolagrass and Stargrasses (Cynodon spp.), use 2 to 4 pints of this 
product per acre to control or suppress weeds after planting vegetative propagules (stolons) of hybrid 
Bermudagrasses. In addition to the weeds listed in Tables 1 and 2, this rate of this product will control or suppress 
annual Sedges, Broadleaf signalgrass, Crabgrass and Goosegrass.
Best results will be obtained if this product is applied at the germinating stage of weeds. Under favorable conditions, 
this is usually 7 to 10 days after planting these grasses. Reduced control can be expected if weeds are allowed to 
reach 1 inch in height before application or if germination of weeds occurs 10 days after application. 
Do not use on Bentgrass, susceptible grass pastures (such as Carpetgrass, Buffalograss or St. Augustine grass), 
Lespedeza, Wild winter peas, Vetch, Clover and Alfalfa pastures as injury will occur. When perennial weeds are 
reaching maturity, mowing and allowing some regrowth will enhance control. Difficult to control weeds and brush 
may require repeat applications. 
For pasture renovations, wait 3 weeks per quart (2 pts.) of Dicamba 2,4-D used per acre before interseeding or 
injury may occur. 
If grasses are grown for seed or for seed-down purposes, do not apply after grass reaches the joint stage. 
Grazing and feeding non-lactating animals: There is no waiting period between treatment and grazing for 
non-lactating animals. Do not permit meat animals being finished for slaughter to graze treated fields within 30 
days of slaughter. 
Grazing and feeding lactating animals: Do not graze lactating dairy animals within 7 days of treatment. 
Dry hay and silage: Treated grasses may be harvested for dry hay or silage but do not harvest within 37 days of 
treatment. 
This product contains 0.36 pound a.e. of 2,4-D per pint. When tank-mixing with products containing 2,4-D, do not 
exceed a combined total of 4 pounds of a.e. per acre per year. 
This product contains 0.125 pound a.e. of Dicamba per pint. When tank-mixing with products containing Dicamba, 
do not exceed a combined total of 1 pound of a.e. per acre per application.
SORGHUM 
Rates and Timings
Apply no more than 2.8 pints of this product per acre to Sorghum in the 3 to 5 leaf stage (4 to 8” tall). For best 
performance, apply this product when weeds are small (less than 3” tall). 
Applications of this product to Sorghum during periods of rapid growth may result in temporary leaning of plants 
or rolling of leaves. These effects are usually outgrown within 10 to 14 days. Sorghum growing under conditions 
of stress such as high moisture, low fertility, and abnormal temperature may be more sensitive to applications of 
this product. 
Do not use surfactants or oils with post-emergence applications of this product on Sorghum crops. 
Do not use this product if the potential for Sorghum injury is not acceptable. 
Do apply within 30 days of harvest. 
Do not permit meat or dairy animals to consume treated crop as fodder or forage for 30 days following application. 
Do not apply this product to Sorghum grown for seed production. 
Make no more than one post-emergence application per growing season. Maximum of 2.8 pints per acre per 
application.


Page13of19

This product contains 0.36 pound a.e. of 2,4-D per pint. When tank-mixing with products containing 2,4-D, do not 
exceed a combined total of 1 pound of a.e. per acre per year. 
This product contains 0.125 pound a.e. of Dicamba per pint. When tank-mixing with products containing Dicamba, 
do not exceed a combined total of 1 pound of a.e. per acre per application.
SUGARCANE
Applications of this product can be made any time after the weeds have emerged and are actively growing but 
prior to the close-in stage of Sugarcane. When possible, direct the spray beneath the Sugarcane canopy in order 
to minimize the likelihood of crop injury. The use of directed sprays will also aid in maximizing spray coverage of 
weed foliage. Application rates and timing are given below. Use the higher level of listed rate ranges when treating 
dense vegetative growth. Do not harvest cane prior to crop maturity. 
Rate
• Pre-emergence: Limited to one application per crop cycle. Maximum of 5.6 pints per acre per application. 
• Post-emergence: Limited to one application per crop cycle. Maximum of 5.6 pints per acre per application 
• Do not apply more than 11.2 pints of this product per acre per crop cycle. 
This product contains 0.36 pound a.e. of 2,4-D per pint. When tank-mixing with products containing 2,4-D, do not 
exceed a combined total of 4 pounds of a.e. per acre per year. 
This product contains 0.125 pound a.e. of Dicamba per pint. When tank-mixing with products containing Dicamba, 
do not exceed a combined total of 1 pound of a.e. per acre per application.
WHEAT (Fall and Spring Seeded) 
If small Grains are grown for pasture or hay, refer to the section “PASTURES, RANGELAND AND GRASS (HAY, 
SILAGE)”.
Do not graze or harvest for livestock feed prior to crop maturity. 
The pre-harvest interval (PHI) is 14 days. 
Limited to 4.8 pints per acre per crop cycle. 
Post-emergence: Limited to one post-emergence application per crop cycle. Maximum of 3.4 pints per acre per 
application. 
Pre-harvest: Limited to one pre-harvest application per crop cycle. Maximum of 1.4 pints per acre per application. 
Do not use this product in Wheat underseeded with Legumes. 
This product contains 0.36 pound a.e. of 2,4-D per pint. When tank-mixing with products containing 2,4-D, do not 
exceed the combined total of 1.25 pounds of a.e. per acre per crop cycle of 2,4-D for post-emergent use. For pre-
harvest application, do not exceed 0.5 pound of 2,4-D a.e. per crop cycle. Do not exceed a total of 1.75 pounds of 
2,4-D a.e. per acre per crop cycle for all uses. 
This product contains 0.125 pound a.e. of Dicamba per pint. When tank-mixing with products containing Dicamba, 
do not exceed a combined total of 1 pound of a.e. per acre per application.
EARLY SEASON APPLICATIONS 
Apply 0.5 to 1 pint of this product per acre to Wheat unless using one of the Wheat specific programs below. Early 
season applications to Spring seeded Wheat must be made after tillering and before Wheat reaches the 6 leaf 
stage. Early season applications to Fall seeded Wheat must be made after tillering and prior to the jointing stage. 
Care should be taken in staging early developing Wheat varieties such as TAM 107, Madison, or Wakefield to be 
certain that the application occurs prior to the jointing stage. A limit of one post-emergence application may be 
made per crop cycle. 
SPECIFIC USE PROGRAMS FOR FALL SEEDED WHEAT ONLY
Up to 1.33 pints of this product per acre may be applied for Fall seeded Wheat after the Wheat begins to tiller for 
suppression of perennial weeds, such as Field bindweed. Applications may be made in the Fall following a frost 
before a killing freeze. Periods of extended stress such as cold and wet weather may enhance the possibility of 
crop injury. For Fall applications only, do not use if the potential for crop injury is not acceptable.


Page14of19

This product may be applied in tank-mixes with herbicides labeled for use on Fall seeded Wheat. Follow all 
directions for use and restrictions in all products involved in tank-mixing. 
PRE-HARVEST APPLICATIONS
This product can be used to control weeds that may interfere with harvest of Wheat. Apply up to 1.4 pints of this 
product per acre as a broadcast or spot treatment to annual broadleaf weeds when Wheat is in the hard dough 
stage and the green color is gone from the nodes (joints) of the stem. A limit of one pre-harvest application may 
be made per crop cycle. Best results will be obtained if application can be made when weeds are actively growing 
but before weeds canopy. A waiting interval of 14 days is required before harvest. Do not use pre-harvest treated 
Wheat for seed unless a germination test is performed on the seed with an acceptable result of 95% germination 
or better. For control of additional broadleaf weeds or grasses, this product may be tank-mixed with other 
herbicides such as Ally or Roundup® Ultra that are registered for pre-harvest use in Wheat. Pre-harvest use of this 
product is not registered for use in California.
BETWEEN CROP APPLICATIONS, CONSERVATION RESERVE PROGRAMS, GENERAL 
FARMSTEAD AND FALLOW 
These uses are considered Food/Feed Crops when harvested, grazed or foraged. Consult the “ADDITIVES” 
section for adjuvant restrictions and the “NON-FOOD/FEED USE” section below for specific use directions. 
NON-FOOD/FEED USE 
(Land not Harvested, Grazed or Foraged) Specific Information
BETWEEN CROP APPLICATIONS
PRE-PLANT DIRECTIONS (POST-HARVEST, FALLOW, CROP STUBBLE, SET ASIDE) FOR BROADLEAF WEED 
CONTROL
This product may be applied pre-plant for the control or suppression of broadleaf weeds in a “pre-plant burn down 
program”. Rates of 0.5 to 5.6 pints may be applied pre-plant alone or in tank-mix with Glyphosate, Touchdown, 
Paraquat, or other products labeled for pre-plant burn down. 
This product can be applied either post-harvest in the Fall, Spring or Summer during the fallow period or to crop 
stubble/set-aside acres. Apply this product as a broadcast or spot treatment to emerged and actively growing 
weeds after crop harvest (post-harvest) before a killing frost or in the fallow cropland or crop stubble the following 
Spring or Summer. 
Only labeled crops can be planted within 30 days of application. Limited to 2 applications per year. Minimum of 30 
days between applications. 
See “Crop Rotational Restrictions” in the “RESTRICTIONS AND LIMITATIONS” section for the specified interval 
between application and planting to prevent crop injury. 
Rates and Timings 
Apply 0.5 to 5.6 pints of this product per acre. Refer to Table 1 to determine use rates for specific targeted weed 
species. Retreatments may be made as needed; however, do not exceed a total of 8 pints of this product per 
treated acre during a growing season. For best performance, apply this product when annual weeds are less than 
6 inches tall, when biennial weeds are in the rosette stage and to perennial weed regrowth in late Summer or Fall 
following a mowing or tillage treatment. The most effective control of upright perennial broadleaf weeds such as 
Canada thistle and Jerusalem artichoke occurs if this product is applied when the majority of weeds have at least 
4 to 6 inches of regrowth or for weeds such as Field bindweed and Hedge bindweed that are in or beyond the full 
bloom stage. 
Avoid disturbing treated areas following application. Treatments may not kill weeds that develop from seed or 
underground plant parts such as rhizomes or bulblets, after the effective period for this product. For seedling 
control, a follow-up program or other cultural practices could be instituted. 
This product contains 0.36 pound a.e. of 2,4-D per pint. When tank-mixing with products containing 2,4-D, do not 
exceed the combined total of 4 pounds of a.e. per acre per year. 
This product contains 0.125 pound a.e. of Dicamba per pint. When tank mixing with products containing Dicamba, 
do not exceed a combined total of 1.0 pound of a.e. per acre per application.


Page15of19

CONSERVATION RESERVE PROGRAMS AND GENERAL FARMSTEAD 
This product is for use fo r Conservation Reserve Programs, general farmstead (non-cropland only), weed and 
brush control or use in State Recognized Noxious Weed areas (non-cropland areas). Refer to Tables 1 and 2 for 
rate selection based on targeted weed or brush species. Some weed species will require tank-mixes for adequate 
control.
For post-emergence control of annual and perennial weeds, a limit of two applications per year can be made with 
a maximum of 5.6 pints per acre per application and a minimum of 30 days between applications. 
For post-emergence control of woody plants, a limit of one application per year can be made with a maximum of 
11.2 pints per acre per year. 
Applications to non-cropland areas are not applicable to treatment of commercial timber or other plants being 
grown for sales or other commercial use or for commercial seed production, or for research purposes. 
For program lands, such as Conservation Reserve Program, consult program rules to determine whether grass or 
hay may be used. The more restrictive requirements of the program rules or this label must be followed. 
This product contains 0.36 pounds a.e. of 2,4-D per pint. When tank-mixing with products containing 2,4-D, do not 
exceed a combined total of 4 pounds of a.e. per acre per year. 
This product contains 0.125 pounds a.e. of Dicamba per pint. When tank-mixing with products containing Dicamba, 
do not exceed a combined total of 1 pound of a.e. per acre per application.
FARMSTEAD AND FENCEROW TREATMENT 
APPLICATION INSTRUCTIONS
This product may be applied using water or oil and water emulsions in spot application to control undesirable 
vegetation using handgun or similar types of application equipment. In addition to weed species listed in Tables 1 
and 2, these treatments may be used to control or suppress woody plant species listed in Table 6.
To prepare oil and water emulsions, mix in the order and proportions indicated below. 
The solution should remain milky colored without an oily layer on top when under agitation. If an oily layer forms, 
increase the amount of emulsifier or change to a more effective emulsifier.
Do not exceed 40 gallons of spray solution per treated acre per application. Forty gallons of spray solution contains 
1.0 pound acid equivalent of Dicamba and 2.87 pounds acid equivalent of 2,4-D. Spray plants to wet. Do not allow 
this spray mix to contact desirable vegetation. To control brush, briars and weeds along fencerows surrounding 
pasture and ranch lands, and fallow fields, use a tank-mix of 2.5% of this product, 87.5% water, 10% diesel oil, 
and sufficient emulsifier (to mix the diesel and emulsifier). The diesel oil in this tank-mix will damage or kill desirable 
grasses and should not be used in pastures or where damage to desirable species cannot be tolerated. 
This product contains 0.36 pound a.e. of 2,4-D per pint. When tank-mixing with products that contain 2,4-D, do not 
exceed a combined total of 4 pounds of a.e. per acre per year. 
This product contains 0.125 pound a.e. of Dicamba per pint. When tank-mixing with products that contain Dicamba, 
do not exceed a combined total of 1 pound of a.e. per acre per application.
1) Water – Begin by agitating a thoroughly clean spray tank with the desired quantity of clean water. Maintain 
constant agitation during complete mixing procedure. 
2) Emulsifier – Add 0.5% volume to volume.
3) This product – Add 2.5 gallons per 100 gallons of total intended solution (maximum 22 pints of this product per 
100 gallons of spray solution) 
4) Diesel oil – Add 10 gallons per 100 gallons of total intended solution. 
5) Maintain constant agitation during application. Under good agitation, the spray solution should be milky white 
with no oil layer on top. If an oil layer forms, increase the amount of emulsifier or change to a more effective 
emulsifier. 
FOR SPRAYING FOLIAR APPLICATIONS
1. Spray when leaves have reached full size but have not hardened due to drought or maturity. 
2. Spray individual plants to wet with handgun. 
3. For larger stems (up to 3” in diameter) and hard to control species, direct spray stream to base of stems to wet 
the stem at sod surface in addition to wetting the foliage. 
4. Do not apply under drip line of desirable trees or adjacent to desirable vegetation


Page16of19

FOR DORMANT BASAL APPLICATIONS
1. Increase diesel oil content to 15% or 15 gallons of diesel oil per 100 gallons of total solution. 
2. Spray in late Winter or early Spring before plants break dormancy. 
3. Spray the bottom 24 inches of the target stem to wet on all sides. 
4. For larger stems (up to 3” in diameter) and hard to kill species direct the spray solution to the base of target 
stems to wet the soil at the stem/soil junction in addition to wetting the stem. 
5. Do not apply under drip line of desirable trees or adjacent to desirable vegetation. 
FOR CUT SURFACE TREATMENTS
Apply this product in an undiluted state as a cut surface treatment to control unwanted trees and prevent sprouts 
of cut trees. 
• Frill or Girdle Treatments : Make a continuous cut or a series of overlapping cuts using an axe to girdle 
tree trunk. Spray or paint the cut surface with this product. 
• Stump Treatments: Spray or paint freshly cut surface with this product. The cambium layer (the area 
adjacent to the bark) should be thoroughly wet. Treat stumps within 6 hours after cutting. 
Limit to one basal spray or cut surface application per year. 
Maximum of 22 pints per 100 gallons of spray solution. 
Table 6. The following list of trees and vines can be controlled on Farmsteads and Fencerows as foliar, 
basal or cut surface treatments:
Alder
Ash
Aspen
Basswood 
Beech
Blackberry 
Black gum 
Cedar 
Cherry 
Chinquapin 
Cottonwood 
Creosote bush 
Dewberry 
Dogwood
Elm
Grape
Greenbriar 
Hawthorn (Thorn apple) 
Hemlock
Hickory 
Honey locust 
Honeysuckle 
Hornbeam 
Huckleberry 
Huisache 
Ivy, Poison 
Kudzu
Locust, Black 
Maple 
Mesquite
Oak
Oak, Poison 
Olive, Russian 
Persimmon, Eastern 
Pine
Plum, Sand 
Poplar 
Rabbitbrush 
Red cedar, Eastern 
Rose, McCartney
Rose, Multi-floral
Sagebrush, Fringe 
Sassafras
Spruce
Sumac
Sweet gum 
Sycamore 
Tarbush 
Willow 
Witch hazel 
Yaupon 
Yucca


Page17of19

Weeds Listed in This Label 
Common Name Scientific Name 
ANNUALS 
Beebalm, Spotted Monarda punctata
Broomweed, Common Gutierrezia dracunculoides
Buckwheat, Wild Polygonum convolvulus
Buffalo bur Solanum rostratum
Burdock Arctium spp.
Buttercup, Corn Ranunculus arvensis
Chickweed, Common Stellaria media
Cockle, Corn Agrostemma githago
Cocklebur, Common Xanthium strumarium
Coreopsis, Plains Coreopsis tinctoria
Croton, Woolly Croton capitatus
Devils claw Proboscidea louisianica
Dogfennel (Cypress weed) Eupatorium capillifolium
Evening primrose, Cutleaf Oenothera laciniata
Flax Linum catharticum
Fleabane, Annual Erigeron annuus
Flixweed Descurainia sophia
Henbit Lamium amplexicaule
Knotweed, Prostrate Polygonum aviculare
Kochia Kochia scoparia
Lambsquarters, Common Chenopodium album
Lettuce, Prickly Lactuca serriola
Mallow, Common Malva neglecta
Morningglory, Ivyleaf Ipomoea hederacea
Morningglory, Tall Ipomoea purpurea
Mustard, Annual Brassica spp.
Mustard, Tansy Descurainia pinnata
Pennycress, Field Thlaspi arvense
Pepperweed, Virginia Lepidium virginicum
Pigweed, Prostrate Amaranthus blitoides
Pigweed, Redroot Amaranthus retroflexus
Pigweed, Smooth Amaranthus hybridus
Pigweed, Tumble Amaranthus albus
Poorjoe Diodia teres
Purslane, Common Portulaca oleracea
Ragweed, Common Ambrosia artemisiifolia
Ragweed, Lance leaf Ambrosia bidentata
Ragweed, Western Ambrosia psilostachya
Sedge Cyperus compressus
Shepherdspurse Capsella bursa-pastoris
Smartweed, Pennsylvania Polygonum pensylvanicum
Sneezeweed, Bitter Helenium amarum
Sunflower, Common (Wild) Helianthus annuus
Thistle, Russian Salsola iberica
Velvetleaf Abutilon theophrasti
BIENNIALS AND PERENNIALS
Bindweed, Field Convolvulus arvensis
Bittercress Cardamine spp.
Buckeye Aesculus spp.
Bullnettle Cnidoscolus stimulosus
Chicory Cichorium intybus
Clover, Hop Trifoleum aureum
Dandelion Taraxacum officinale
Dock, Curly Rumex crispus
Elderberry Sambucus canadensis
Goldenrod, Missouri Solidago missouriensis
 (Continued)


Page18of19

(Continuation) 
Goldenweed, Common Isocoma coronopifolia
Groundsel Senecio vulgaris
Honeysuckle, Hairy Lonicera
Horsenettle Solanum carolinense
Ivy, Poison Rhus radicans
Knapweed, Black Centaurea nigra
Knapweed, Russian Centaurea repens
Knapweed, Spotted Centaurea maculosa
Marshelder Iva annua
Mesquite Prosopis juliflora
Milkweed, Antelopehorn Asclepias
Nightshade, Silverleaf Solanum elaeagnifolium
Nightshade, Black Solanum nigrum
Persimmon, Eastern Diospyros virginiana
Rabbitbrush Chrysothamnus pulchellus
Ragwort, Tansy Senecio jacobaea
Redvine Brunnichia ovata
Sagebrush, Fringed Artemisia frigida
Smartweed, Swamp Polygonum coccineum
Sorrel, Red (Sheep Sorrel) Rumex acetosella
Sowthistle, Perennial Sonchus arvensis
Spurge, Leafy Euphorbia esula
Starthistle, Yellow Centaurea solstitialis
Tallow Tree, Chinese Sapium sebiferum
Thistle, Bull Cirsium vulgare
Thistle, Canada Cirsium arvense
Thistle, Musk Carduus nutans
Thistle, Plumeless Carduus acanthoides
Vetch Vicia spp.
Yankeeweed Eupatorium compositifolium
STORAGE AND DISPOSAL 
Do not contaminate water, food or feed by storage or disposal. 
PESTICIDE STORAGE: Store in original container in secured dry storage area. Prevent cross-contamination 
with other pesticides and fertilizers. Do not store above 100ºF for extended periods of time. Storage below 20ºF 
may result in formation of crystals. If product crystallizes, store at 50ºF to 70ºF and agitate to redissolve crystals. 
If container is damaged or spill occurs, use product immediately or dispose of product and damaged container 
as indicated below. 
PESTICIDE DISPOSAL: Open dumping is prohibited. Improper disposal of excess pesticide, spray mixture or 
rinsate is a violation of Federal law. If these wastes cannot be disposed of by use according to label instructions, 
contact your State Pesticide or Environmental Control Agency or the Hazardous Wa ste Representative at the 
nearest EPA Regional Office for guidance. 
CONTAINER HANDLING: 
Nonrefillable Container (rigid material; less than 5 gallons): Nonrefillable container. Do not reuse or refill 
this container. Offer for recycling, if available. Triple rinse container (or equivalent) promptly after emptying. 
Triple rinse as follows: Empty the remaining contents into application equipment or a mix tank and drain for 10 
seconds after the flow begins to drip. Fill the container one-fourth full with water and recap. Shake for 10 
seconds. Pour rinsate into application equipment or a mix tank or store rinsate for later use or disposal. Drain 
for 10 seconds after the flow begins to drip. Repeat this procedure two more times. Then offer for recycling if 
available or puncture and dispose of in a sanitary landfill, or by incineration. 
(Continued)


Page19of19

(Continuation)
Nonrefillable Container (rigid material; 5 gallons up to < 250 gallons): Nonrefillable container. Do not reuse 
or refill this container. Offer for recycling, if available. Triple rinse container (or equivalent) promptly after 
emptying. Triple rinse as follows: Empty the remaining contents into application equipment or a mix tank. Fill the 
container one-fourth full with water. Replace and tighten closures. Tip container on its side and roll it back and 
forth, ensuring at least one complete revolution, for 30 seconds. Stand the container on its end and tip it back 
and forth several times. Turn the container over onto its other end and tip it back and forth several times. Empty 
the rinsate into application equipment or a mix tank or store rinsate for later use or disposal. Repeat this 
procedure two more times. Then offer for recycling if available or puncture and dispose of in a sanitary landfill, 
or by incineration. 
Refillable Container (> 250 gallons & Bulk): Refillable container. Refill this container with pesticide only. Do 
not reuse this container for any other purpose. Cleaning the container before final disposal is the responsibility 
of the person disposing of the container. Cleaning before refilling is the responsibility of the refiller. To clean the 
container before final disposal, empty the remaining contents from this container into application equipment or 
mix tank. Fill the container about 10% full with water. Agitate vigorously or recirculate water with the pump for 2 
minutes. Pour or pump rinsate into application equipment or rinsate collection system. Repeat this rinsing 
procedure two more times. Then offer for recycling if available or puncture and dispose of in a sanitary landfill, 
or by incineration, or, by other procedures approved by State and local authorities. 
SPILLS: For minor spills, leaks, etc., follow all precautions indicated on this label and clean up immediately. 
Take special care to avoid contamination of equipment and facilities during cleanup procedures and disposal of 
wastes. Handle and open container in a manner as to prevent spillage. If the container is leaking, invert to 
prevent leakage. If container is leaking or material spilled for any reason or cause, carefully dam up spilled 
material to prevent runoff. Refer to Precautionary Statements on label for hazards associated with the handling 
of this material. Do not walk through spilled material. Absorb spilled material with absorbing type compounds 
and dispose of as directed for pesticides below. In spill or leak incidents, keep unauthorized people away. You 
may contact the CHEMTREC Emergency Response for decontamination procedures. 
FOR CHEMICAL EMERGENCY: Spill, leak, fire, exposure or accident, call CHEMTREC 1-800-424-9300.
WARRANTY—CONDITIONS OF SALE 
OUR DIRECTIONS FOR USE of this product are based upon tests believed reliable. Follow directions carefully. 
Timing and method of application, weather and crop conditions, mixtures with other chemicals not specifically 
directed and other influencing factors in the use of this product are beyond the control of the Seller. To the extent 
consistent with applicable law, Buyer assumes all risks of use, storage and handling of this material not in strict 
accordance with directions given herewith. To the extent consistent with applicable law, in no case shall the 
Manufacturer or the Seller be liable for consequential, special or indirect damages resulting from the use or 
handling of this product when such use and/or handling is not in strict accordance with directions given herewith. 
The foregoing is a condition of sale by the Seller and is accepted as such by the Buyer. 
 
 M
anufactured By: 

DE-AMINE and the Drexel logo are either trademarks or registered trademarks of Drexel Chemical Company. All other brand names, product names or trademarks 
belong to their respective holders.