crop-chem-docs/corpus/epa_ppls/264-1238.md

# Acceleron 26FO Fungicide Seed Treatment

- EPA Reg No: **264-1238**
- Registrant: BAYER CROPSCIENCE, LLC
- Signal word: Caution
- Active ingredients: Fluoxastrobin (4.55%); Metalaxyl (9.1%); Prothioconazole (4.55%)
- Label accepted: 2025-04-09
- Source PDF: https://www3.epa.gov/pesticides/chem_search/ppls/000264-01238-20250409.pdf

---
1
U.S. ENVIRONMENTAL PROTECTION AGENCY
Office of Pesticide Programs
Registration Division (7505T)
1200 Pennsylvania Ave., N.W.
Washington, D.C. 20460
EPA Reg. Number:
264-1238
Date of Issuance:
4/9/25
NOTICE OF PESTICIDE: 
 X Registration
 Reregistration
Term of Issuance: 
Unconditional
 (under FIFRA, as amended)
Name of Pesticide Product:
Acceleron 26FO Fungicide Seed 
Treatment
Name and Address of Registrant (include ZIP Code):
Bayer CropScience LP
800 N. Lindbergh Blvd.
St. Louis, MO 63167
Note: Changes in labeling differing in substance from that accepted in connection with this registration must be submitted to and accepted by the 
Registration Division prior to use of the label in commerce. In any correspondence on this product always refer to the above EPA registration number.
On the basis of information furnished by the registrant, the above named pesticide is hereby registered 
under the Federal Insecticide, Fungicide, and Rodenticide Act (FIFRA).
Registration is in no way to be construed as an endorsement or recommendation of this product by the 
Agency. In order to protect health and the environment, the Administrator, on his motion, may at any 
time suspend or cancel the registration of a pesticide in accordance with the Act. The acceptance of 
any name in connection with the registration of a product under this Act is not to be construed as 
giving the registrant a right to exclusive use of the name or to its use if it has been covered by others.
This product is unconditionally registered in accordance with FIFRA section 3(c)(5) provided that you:
1. Submit and/or cite all data required for regist ration/reregistration/registration review of your 
product when the Agency requires all registrants of similar products to submit such data.
Continues page 2
Signature of Approving Official:
Manjula Unnikrishnan Product Manager 21
Fungicide Branch
Registration Division (7505T)
Date:
 4/9/25
EPA Form 8570-6

Page 2 of 2 
EPA Reg. No. 264-1238 
Case No. 488949 
 
2. Make the following label changes before you release the product for shipment: 
 
x Revise the EPA Registration Number to read, “EPA Reg. No. 264-1238.” 
 
3. Submit one copy of the final printed label for the record before you release the product for 
shipment. 
4. Add an appropriate EPA Establishment Number 
 
Should you wish to add/retain a reference to the company’s website on your label, then please be 
aware that the website becomes labeling under FIFRA and is subject to review by the Agency. If the 
website is false or misleading, the product would be misbranded and unlawful to sell or distribute 
under FIFRA section 12(a)(1)(E). 40 CFR 156.10(a)(5) lists examples of statements EPA may consider 
false or misleading. In addition, regardless of whether a website is referenced on your product’s label, 
claims made on the website may not substantially differ from those claims approved through the 
registration process. Therefore, should the Agency find or if it is brought to our attention that a 
website contains false or misleading statements or claims substantially differing from the EPA 
approved registration, the website will be referred to the EPA’s Office of Enforcement and Compliance. 
 
If these conditions are not complied with, the registration will be subject to cancellation in accordance 
with FIFRA section 6. Your release for shipment of the product constitutes acceptance of these 
conditions. A stamped copy of the label is enclosed for your records. 
 
The record for this product currently contains the following CSF(s): 
 
x Basic CSF dated 05/06/2024 
x Alternate CSF 1 dated 05/06/2024 
 
If you have any questions, please contact Senedu Alemu at alemu.senedu@epa.gov. 
 
 
Enclosure

1 
Acceleron 26FO Fungicide Seed Treatment 
[ABN: Acceleron Prime Fungicide, Acceleron Solutions Prime 
F, Acceleron Prime F]
A SEED TREATMENT PRODUCT FOR CONTROL OF SEED ROT AND DAMPING-OFF 
DISEASES ON SOYBEAN – FOR COMMERCIAL SEED TREATMENT ONLY
ACTIVE INGREDIENTS:
Metalaxyl: N-(2,6-dimethylphenyl)-N-(methoxyacetyl)alanine methyl ester……………………………………………… . 9.10%
Prothioconazole: 2-[2-(1- Chlorocylocpropyl)-3-(2-chlorophenyl)-2-hydroxypropyl]- 1,2- dihydro-3H-1,2,4-triazole-3-
thione…………………………………………………………………………………………………………………………… 4.55%
Fluoxastrobin: ((2E)-(2-[6-(2-chlorophenoxy)-5-fluoro-4pyrimidinyl] oxy phenyl)- 
(5, 6-dihydro-1, 4, 2-dioxazin-3yl) methanone O-methyloxime)......................................................................................4.55%
OTHER INGREDIENTS: …………………………………………………………………………………………………….. 81.80%
TOTAL: 100.00%
Contains 0.83 pounds Metalaxyl per gallon (100 grams ai/liter)
Contains 0.42 pounds Prothioconazole per gallon (50 grams ai/liter) 
Contains 0.42 pounds Fluoxastrobin per gallon (50 grams ai/liter)
EPA Reg. No. 264-XXXX EPA Est. 
KEEP OUT OF REACH OF CHILDREN
CAUTION 
PRECAUCIÓN
Si usted no entiende la etiqueta, busque a alguien para que se la explique a usted en detalle. (If you do not understand the label, find 
someone to explain it to you in detail.)
For MEDICAL and TRANSPORTATION Emergencies ONLY Call 24 Hours A Day 1-800-334-7577
For PRODUCT USE Information Call 1-866-99BAYER (1-866-992-2937)
Please refer to [back panel] [booklet] for additional precautionary statements and directions for use. [Instruction
to reviewer: Location of additional precautionary statements and directions for use will vary between those 
listed, depending on container type/size.]
FIRST AID
IF SWALLOWED: x Call a poison control center or doctor immediately for treatment advice.
x Have person sip a glass of water if able to swallow.
x DO NOT induce vomiting unless told to do so by a poison control center or doctor.
x DO NOT give anything by mouth to an unconscious person.
IF ON SKIN OR 
CLOTHING:
x Take off contaminated clothing.
x Rinse skin immediately with plenty of water for 15-20 minutes.
x Call a poison control center or doctor for treatment advice.
IF IN EYES: x Hold eye open and rinse slowly and gently with water for 15-20 minutes.
x Remove contact lenses, if present, after the first 5 minutes, then continue rinsing. 
x Call a poison control center or doctor for treatment advice.
IF INHALED: x Move person to fresh air.
x If person is not breathing, call 911 or an ambulance, then give artificial respiration, preferably by mouth-to-
mouth, if possible.
x Call a poison control center or doctor for treatment advice.
In case of emergency call toll free the Bayer CropScience Emergency Response Telephone No. 1-800-334-7577.
Have a product container or label with you when calling a poison control center or doctor, or going for treatment.
METALAXYL GROUP 4 FUNGICIDE
PROTHIOCONAZOLE GROUP 3 FUNGICIDE
FLUOXASTROBIN GROUP 11 FUNGICIDE
264-1238
04-09-2025

2 
 
PRECAUTIONARY STATEMENTS 
HAZARDS TO HUMANS AND DOMESTIC ANIMALS 
CAUTION 
Harmful if swallowed or absorbed through skin. Avoid contact with skin, eyes, or clothing. Wash thoroughly with soap and water after 
handling and before eating, drinking, chewing gum, using tobacco, or using the toilet. Remove and wash contaminated clothing be fore 
reuse. 
 
PERSONAL PROTECTIVE EQUIPMENT (PPE) 
Workers involved with treating the seed (i.e., operating the treating equipment, loading the chemical, or calibrating the 
treating equipment); packaging the treated seed (i.e., bagging, closing, tagging, stacking, or forklifting); cleanout of the 
treatment chamber; or loading and planting treated seeds must wear: 
x Long-sleeved shirt and long pants 
x Socks plus shoes 
x Chemical-resistant gloves made RI EDUULHU ODPLQDWH EXW\O UXEEHU • PLOV QLWULOH UXEEHU • PLOV QHRSUHQH UXEEHU •
PLOVSRO\HWK\OHQHSRO\YLQ\OFKORULGH•PLOVRU9LWRQ•PLOV 
 
USER SAFETY RECOMMENDATIONS 
Users should: 
x Remove clothing/PPE immediately if pesticide gets inside. Then wash thoroughly and put on clean clothing. 
x Remove PPE immediately after handling this product. Wash the outside of gloves before removing. As soon as possible, wash 
thoroughly and change into clean clothing. 
USER SAFETY REQUIREMENTS 
Follow the manufacturer’s instructions for cleaning/maintaining PPE. If no such instructions exist for washables, use detergent and hot 
water. Keep and wash PPE separately from other laundry. 
 
ENVIRONMENTAL HAZARDS 
 
This product is toxic to freshwater fish, freshwater and estuarine/marine aquatic invertebrates, and freshwater/estuarine/marine aquatic 
plants. Runoff may be hazardous to aquatic organisms in water adjacent to treated areas. The active ingredients in this product can be 
persistent for several months or longer. For terrestrial uses, DO NOT apply to water or to areas where surface water is present or to 
intertidal areas below the mean high water mark. DO NOT contaminate water when disposing of equipment washwater or rinsate. 
Treated seed exposed on soil surface may be hazardous to wildlife. Cover or collect seed spilled during loading. 
 
Groundwater Advisory 
Metalaxyl, prothioconazole-desthio (a degradate of prothioconazole), and fluoxastrobin are known to leach through soil into 
groundwater under certain conditions as a result of agricultural use. Use of this product in areas where soils are permeable, particularly 
where the water table is shallow, may result in groundwater contamination. 
 
DIRECTIONS FOR USE 
It is a violation of Federal law to use this product in a manner inconsistent with its labeling. 
Read the entire label before using this product. 
 
 
PRODUCT INFORMATION 
Acceleron 26FO Fungicide Seed Treatment is a systemic fungicide seed treatment specifically for control of root and stem rot caused 
by Rhizoctonia solani, Fusarium spp., and Phytophthora spp., and Seed Decay caused by, Fusarium spp., Aspergillus spp., Penicillium 
spp., and Phomopsis spp. 
 
USE RESTRICTIONS 
x For use only in commercial seed treatment facilitates. Not for use in agricultural establishments in hopper-box, planter-box, 
slurry-box, or other seed treatment applications at or immediately before planting. 
x Seed treated with this product must be visually identifiable from untreated seed by the use of an approved colorant or dye to 
prevent accidental use of treated seed as food for humans or feed for animals. Refer to 21 CFR, Part 2.25. Any colorant or dye 
added to treated seed must be cleared for use in accordance with 40 CFR, Part 153.155(c).

3 
 
x Maximum usage when applying metalaxyl- and mefenoxam-co ntaining products, fluoxastrobin-containing products and 
prothioconazole-containing products to the same crop within the same season: DO NOT apply more than the maximum yearly 
total application rate for the active ingredient as stated on the label of the product containing the lowest yearly total on th at 
crop. 
x DO NOT apply more than 2.3 fl oz/cwt of Acceleron 26FO Fungicide Seed Treatment to soybeans. 
x DO NOT graze or feed livestock on soybean forage or hay. 
x DO NOT allow children, pets, or livestock to have access to treated seed. 
x DO NOT use treated seed for food, feed, or oil. 
x Not for Sale, Sale Into, Distribution and /or Use in Nassau and Suffolk Counties of New York State. 
x Refer to the specific use directions and restrictions in the crop table. 
x Store treated seed away from feeds and foodstuffs. 
x Plant treated seed into the soil at a minimum depth of 1/2 inch or greater to minimize exposure. 
 
 
RESISTANCE MANAGEMENT RECOMMENDATION 
For resistance management, please note that Acceleron 26FO Fungicide Seed Treatment contains Group 4, Group 3, and a Group 11 
fungicide. Any fungal population may contain individuals naturally resistant to Acceleron 26FO Fungicide Seed Treatment and other 
Group 4, Group 3, or Group 11 fungicides. A gradual or total loss of pest control may occur over time if these fungicides are used 
repeatedly in the same fields. Appropriate resistance-management strategies must be followed. 
To delay fungicide resistance, take one or more of the following steps: 
x Rotate the use of Acceleron 26FO Fungicide Seed Treatment or other Group 4, Group 3, and 11 fungicides within a growing 
season sequence with different groups that control the same pathogens. 
x Use tank mixtures with fungicide from a different group that are equally effective on the target pest when such use is 
permitted. Use at least the minimum application rate as labeled by the manufacturer. 
x Adopt an integrated disease management program for fungicide use that includes scouting, uses historical information related 
to pesticide use, and crop rotation, and which considers host plant resistance, impact of environmental conditions on disease 
development, disease thresholds, as well as cultural, biological and other chemical control practices. 
x Where possible, make use of predictive disease models to effectively time fungicide applications. Note that using predictive 
models alone is not sufficient to manage resistance. 
x Monitor treated fungal populations for resistance development. 
x Contact your local extension specialist or certified crop advisor for any additional pesticide resistance-management and/or IP M 
guidance for specific crops and pathogens. 
x For information or to report suspected resistance contact Bayer CropScience LP at 1-866-99BAYER (1-866-992-2937). You 
can also contact your pesticide distributor or university extension specialist to report resistance. 
 
APPLICATION INSTRUCTIONS 
x Uniform application of seed is necessary to ensure seed safety and best disease protection. 
x Dilute with a sufficient amount of water to achieve uniform application to seed which is necessary to ensure seed safety and 
best disease control. 
x Apply using standard slurry or mi st-type seed treatment equipment. 
x Use high quality, properly cleaned seed. 
 
ROTATIONAL CROPS* 
In the event of a crop failure or harvest of a crop grown from seed treated with Acceleron 26FO Fungicide Seed Treatment, the field 
maybe replanted immediately with any crops. 
*Cover crops for soil building or erosion control may be planted any time, but DO NOT graze or harvest for food or feed, unless a crop 
tolerance exists. 
 
COMPATIBILITY TESTING AND TANK MIX PARTNERS 
May be used in combination with other registered Bayer CropScience fungicide seed treatments and insecticides. Pre-test for 
compatibility with other seed treatment products. 
 
Compatibility 
It is essential that before using Acceleron 26FO Fungicide Seed Treatment in any tank mixture the compatibility of the mixture be 
established. Add Acceleron 26FO Fungicide Seed Treatment at the labeled rate to a clean quart jar containing approximately one-half 
the amount of water intended for a final slurry application rate. Next, follow with all other tank mix components that will be used in the 
total slurry application. 
 
Add last the remaining balance of water. The total amount of volume is determined by the seed size and how much is necessary to 
ensure complete and uniform coverage and distribution on the seed, as well as the type of commercial seed treating application 
equipment that will be used. 
 
DO NOT USE MIXTURES THAT CURDLE, PRECIPITATE, OR GEL. USE TANK MIXTURES IMMEDIATELY AFTER MIXING WITH

4 
 
ADEQUATE AGITATION. 
 
Mixing Instructions 
1. When applied with seed treatment application equipment design ed to treat seed utilizing a treatment slurry mixture, add 
approximately 1/2 to 2/3 of the required water to the treatment slurry tank followed by the accompanying seed treatment 
products and Acceleron 26FO Fungicide Seed Treatment. 
2. The order of product addition is dependent on the accompanying seed treatment products and application equipment used. 
3. Allow each slurry component to disperse completely prior to the next addition until a uniform suspension is obtained. 
4. After all slurry components have been added and dispersed completely add the remaining 1/2 to 1/3 of required water for 
proper slurry volume and mix until uniform. For containers over 15 gallons, mix the product with the built-in mixer for 5-10 
minutes before each use. 
5. DO NOT store mixed slurries for greater than 72 hours. Always recirculate or mix thoroughly before using. 
6. Maintain adequate agitation until treatment slurry is applied. 
For additional instructions for mixing, use, slurry component mixing order, and other application suggestions contact your Bayer 
CropScience representative. 
 
Follow more restrictive labeling of any tank mix partner. DO NOT tank mix with any product, which contains a prohibition on tank 
mixing. Acceleron 26FO Fungicide Seed Treatment may be applied as a water-based slurry with other registered seed treatment 
insecticides and fungicides through standard slurry or mist-type commercial seed treatment equipment. 
It is the pesticide user’s responsibility to ensure that all products are registered for the intended use. Read and follow the applicable 
restrictions and limitations and directions for use on all product labels involved in tank mixing. Users must follow the most r estrictive 
directions for use and precautionary statements of each product in the tank mixture. Excess treated seed may be used for ethano l 
production only if (1) by-products are not used for livestock feed and (2) no measurable residues of pesticide remain in ethano l 
byproducts that are used in agronomic practice. 
 
CROP USE DIRECTIONS 
Soybean 
Diseases 
Controlled 
Product Rate gram ai/100 Kg seed mg ai/seed 
Aid in control and 
suppression of 
seedborne disease 
and early season 
seedling disease- 
Root & Stem Rot- 
Rhizoctonia solani, 
Fusarium spp., 
Pythium spp., and 
Phytophthora spp. 
Seed Decay- 
Fusarium spp., 
Aspergillus spp., 
Penicillium spp., 
and Phomopsis 
spp. 
2.3 fl oz/cwt* 
 
 
Metalaxyl - 15 
 
Fluoxastrobin - 7.5 
 
Prothioconazole - 7.5 
 
Total - 30 
 
Metalaxyl – 0.024 
 
Fluoxastrobin – 0.012 
 
Prothioconazole – 0.012 
 
Total - 0.048 
* Based on 2,800 soybean seeds/lb 
For soybeans with average size of 2,800 soybean seeds/lb and average seeding rate of 140,000 seed/A the recommended rate 
of 2.3 fl oz/100 lb seeds will result in: 0.015 lbs metalaxyl, 0.0075 lbs fluoxastrobin, and 0.0075 lbs prothioconzaole per 100 lbs 
of seeds.

5 
 
SEED BAG LABEL REQUIREMENTS 
Federal Seed Act requires that containers containing treated seeds shall be labeled with the following information. 
x This seed has been treated with: 
o Acceleron 26FO Fungicide Seed Treatment (EPA Reg. No . 264-XXXX) which contains 9.10% Metalaxyl, 4.55% 
Prothioconazole, and 4.55% Fluoxastrobin. 
x DO NOT use for feed, food or oil purposes. 
 
The U.S. Environmental Protection Agency requires the following statements on containers containing seed treated with Acceleron 
26FO Fungicide Seed Treatment (EPA Reg. No. 264-XXXX): 
 
x Treated areas may be replanted with any crop specified on this l abel as soon as practical after last application. For crops not 
listed on this label, DO NOT plant back within 30 days of last application. 
x Store treated seed away from feeds and foodstuffs. 
x DO NOT allow children, pets, or livestock to have access to treated seeds. 
x When opening this bag or loading/pouring the treated seed or seed pieces, wear long sleeved shirt, long pants, 
shoes, socks, and chemical-resistant gloves. 
x Treated seeds exposed on the soil surface may be hazardous to wildlife. Cover or collect treated seeds spilled during loading 
and planting (for example in row ends). 
x Dispose of all excess treated seed by burying seed away from bodies of water. 
x DO NOT contaminate bodies of water when disposing of planting equipment wash water. 
x DO NOT plant treated seeds in areas subject to seasonal or extended periods of standing water. 
x Dispose of seed packaging or containers in accordance with local requirements. 
x Excess treated seed may be used for ethanol production if (1) by-products are not used for livestock feed and (2) no 
measurable residues of pesticide remain in ethanol by-products that are used in agronomic practice. 
x Treated seed must be adequately covered with soil at planting. 
x Ensure that planting equipment is functioning properly in accordance with manufacturing specifications to minimize seed coat 
abrasion during planting to reduce dust which can drift to blooming crops or weeds. 
x Plant treated seed into the soil at a minimum depth of 1/2 inch or greater to minimize exposure. 
x DO NOT plant treated seed by broadcasting to the soil surface. Ensure that all planted seeds are thoroughly incorporated by 
the planter during planting, additional incorporation may be required to thoroughly cover exposed seeds. 
x Seed treated with this product must be visually identifiable from untreated seed by the use of an approved colorant or dye to 
prevent accidental use of treated seed as food for humans or feed for animals. Refer to 21 CFR, Part 2.25. Any colorant or dye 
added to treated seed must be cleared for use in accordance with 40 CFR, Part 153.155(c). 
x This seed has been treated with 0.015 lbs. metalayxl, 0.0075 lb s. fluoxastrobin, and 0.0075 lbs. prothioconazole per 100 lbs. 
of seeds (based on 2800 soybean seed/lb, 0.024 mg metalaxyl, 0.012 mg fluoxastrobin, and 0.012 mg prothioconazole per 
seed).

6 
 
STORAGE AND DISPOSAL 
DO NOT contaminate water, food, or feed by storage or disposal. 
 
PESTICIDE STORAGE 
Store in a cool dry location. DO NOT store in direct hot sunlight. DO NOT store above 90°F for prolonged periods of time. After 
prolonged storage in intense cold, allow product to return to approximately 75°F before using. 
 
PESTICIDE DISPOSAL 
Wastes resulting from the use of this product may be disposed of on site or at an approved waste disposal facility. 
 
CONTAINER HANDLING 
Rigid, Non-refillable containers small enough to shake (i.e., with capacities equal to or less than 5 gallons). 
Non-refillable container. DO NOT reuse or refill this container. Offer for recycling, if available. Triple rinse or pressure rinse container (or 
equivalent) promptly after emptying. 
Triple rinse as follows: Empty the remaining contents into application equipment or a mix tank and drain for 10 seconds after t he flow 
begins to drip. Fill the container ¼ full with water and recap. Shake for 10 seconds. Pour rinsate into application equipment o r a mix 
tank or store rinsate for later use or disposal. Drain for 10 seconds after the flow begins to drip. Repeat this procedure two more times. 
Pressure rinse as follows: Empty the remaining contents into application equipment or a mix tank and continue to drain for 10 s econds 
after the flow begins to drip. Hold container upside down over application equipment or mix tank or collect rinsate for later u se or 
disposal. Insert pressure-rinsing nozzle in the side of the container, and rinse at about 40 PSI for at least 30 seconds. Drain for 10 
seconds after the flow begins to drip. 
Once container is rinsed, offer for recycling if available, or puncture and dispose of in a sanitary landfill or incineration, or if allowed by 
state and local authorities, by burning. If burned stay out of smoke. 
 
Rigid Non-refillable containers that are too large to shake (i.e., with capacities greater than 5 gallons or 50 lbs) 
 
Non-refillable Containers 
Non-refillable containers - DO NOT reuse or refill this container. After emptying product from container, either return container to Bayer 
CropScience per instructions from Bayer CropScience Customer Se rvice Center (1-800-527-4781), or rinse and either recycle or 
dispose of the container as follows: 
 
Bottom Discharge IBC (e.g. – Schuetz Caged IBC or Snyder Square Stackable) 
Pressure rinsing the container before final disposal is the responsibility of the person disposing of the container. To pressur e rinse the 
container before final disposal, empty the remaining contents from the IBC into application equipment or mix tank. Raise the bo ttom of 
the IBC by 1.5 inches on the side which is opposite of the bottom discharge valve to promote more complete product removal. 
Completely remove the top lid of the IBC. Use water pressurized to at least 40 PSI to rinse all interior portions. Continuously pump or 
drain rinsate into application equipment or rinsate collection system while pressure rinsing. Continue pressure rinsing for 2 m inutes or 
until rinsate becomes clear. Replace the lid and close bottom valve. 
 
Top Discharge IBC, Drums, Kegs (e.g.– Snyder 120 Next Gen, Bonar B120, Drums, and Kegs) 
Triple rinsing the container before final disposal is the respon sibility of the person disposing of the container. To triple ri nse the 
container before final disposal, empty the remaining contents from this container into application equipment or mix tank. Fill the 
container at least 10 percent full with water. Agitate vigorously or recirculate water with the pump for 2 minutes. Rinse all i nterior 
surfaces. Pour or pump rinsate into application equipment or rinsate collection system. Repeat this procedure two more times. 
 
Once container is rinsed, offer for recycling if available or puncture and dispose of in a sanitary landfill, or by incineration. 
 
Refillable Containers 
Refillable container. Refill this container with pesticide only. DO NOT reuse this container for any 
other purpose. DO NOT remove tamper evident cables or one-way valves or cl ean the container if the container is equipped with one-
way valves and refilling or returning is planned. After emptying product from container, either return container to Bayer CropS cience per 
instructions from Bayer CropScience Customer Service Center (1-800-527-4781) or rinse and either recycle or dispose of the cont ainer 
as follows: 
 
Bottom Discharge IBC (e.g. – Schuetz Caged IBC or Snyder Square Stackable) 
Pressure rinsing the container before final disposal is the responsibility of the person disposing of the container. Cleaning b efore 
refilling is the responsibility of the refiller. To pressure rinse the container before final disposal, empty the remaining con tents from the 
IBC into application equipment or mix tank. Raise the bottom of the IBC by 1.5 inches on the side which is opposite of the bott om 
discharge valve to promote more complete product removal. Completely remove the top lid of the IBC. Use water pressurized to at least 
40 PSI to rinse all interior portions. Continuously pump or drai n rinsate into application equipment or rinsate collection syst em while 
pressure rinsing. Continue pressure rinsing for 2 minutes or until rinsate becomes clear. Replace the lid and close bottom valve.

7 
Top Discharge IBC, Drums, Kegs (e.g. – Snyder 120 Next Gen, Bonar B120, Drums, and Kegs)
Triple rinsing the container before final disposal is the responsibility of the person disposing of the container. Cleaning bef ore refilling is 
the responsibility of the refiller. To triple rinse the containers before final disposal, empty the remaining contents from thi s container into 
application equipment or mix tank. Fill the container at least 10 percent full with water. Agitate vigorously or recirculate wa ter with the 
pump for 2 minutes. Rinse all interior surfaces. Pour or pump ri nsate into application equipment or rinsate collection system. Repeat 
this procedure two more times.
Once container is rinsed, offer for recycling if available or puncture and dispose of in a sanitary landfill or by incineration. 
IMPORTANT: READ BEFORE USE
CONDITIONS OF SALE AND LIMITATIONS OF WARRANTY AND LIABILITY
Read the entire Directions for Use, Conditions, Disclaimer of Warranties and Limitations of Liability before using this product. If terms are 
not acceptable, return the unopened product container at once.
By using this product, user or buyer accepts the following Conditions, Disclaimer of Warranties and Limitations of Liability.
Treatment of highly mechanically damaged seed, or seed of known lo w vigor and poor quality, may result in reduced germination an d/or 
reduction of seed and seedling vigor. Treat and conduct germination tests on a small portion of seed before committing the tota l seed lot 
to a selected chemical treatment. Due to seed quality conditions beyond the control of Bayer CropScience, no claims are made to 
guarantee germination of carry-over seed.
CONDITIONS: The directions for use of this product are believed to be adequate and must be followed carefully. However, it is 
impossible to eliminate all risks associated with the use of this product. Crop injury, ineffectiveness or other unintended con sequences 
may result because of such factors as weather conditions, presence of other materials, or the manner of use or application, all of which 
are beyond the control of Bayer CropScience. All such risks shall be assumed by the user or buyer.
DISCLAIMER OF WARRANTIES: TO THE EXTENT CONSISTENT WITH APPL ICABLE LAW, BAYER CROPSCIENCE MAKES NO 
WARRANTIES, EXPRESS OR IMPLIED, OF MERCHANTABILITY OR OF FITN ESS FOR A PARTICULAR PURPOSE OR 
OTHERWISE, THAT EXTEND BEYOND THE STATEMENTS MADE ON THIS LABEL. No agent of Bayer CropScience is authorized to 
make any warranties beyond those contained herein or to modify the warranties contained herein. TO THE EXTENT CONSISTENT 
WITH APPLICABLE LAW, %$<(5 &5236&,(1&( ',6&/$,06 $1< /,$%,/,7< :+$762(9(5 )25 63(&,$/ ,1&,'(17$/ 25
CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OR HANDLING OF THIS PRODUCT.
LIMITATIONS OF LIABILITY: TO THE EXTENT CONSISTENT WITH APPLICABLE LAW, 7+((;&/86,9(5(0('<2)7+(86(5
OR BUYER FOR ANY AND ALL LOSSES, INJURIES OR DAMA GES RESULTING FROM THE USE OR HANDLING OF THIS 
PRODUCT, WHETHER IN CONTRACT, WARRA NTY, TORT, NEGLIGENCE, STRICT LI ABILITY OR OTHERWISE, SHALL NOT 
EXCEED THE PURCHASE PRICE PAID, OR AT BAYER CROPSCIENCE’S ELECTION, THE REPLACEMENT OF PRODUCT.
NET CONTENTS: 
PRODUCED FOR
Bayer CropScience LP
800 N. Lindbergh Blvd.
St. Louis, MO 63167
1-866-99BAYER (1-866-992-2937)
Acceleron 26FO Fungicide Seed Treatment (PENDING) 8/02/2023, 02/26/2025, 03/03/2025, 03/04/2025, 03/31/2025, 04/04/2025