crop-chem-docs/corpus/bayer/movento.md

# Movento Insecticide

- **Product class:** insecticide
- **EPA Reg No:** 264-1050
- **Active ingredients:** Spirotetramat
- **Source:** https://www.cropscience.bayer.us/crop-protection/insecticide/movento-insecticide
- **Label PDF:** https://cs-assets.bayer.com/is/content/bayer/Movento2h_Labelpdf

---

Net Contents:
1 Gallon  GROUP INSECTICIDE23
US61381471D       170628Dv3    07/26
US61381471D (170628Dv3) NAME 1 GALLON ETL
COLORS: CMYK     DATE: 07/08/2026  Label Coordinator: Louis Cross

For Agricultural Use Only: For control of listed insects
on certain tree, tropical fruits, vine, and vegetable crops.
ACTIVE INGREDIENT: Spirotetramat:
cis-3-(2,5-dimethylphenyl)-8-methoxy-2-oxo-1-azaspiro
[4.5]dec-3-en-4-yl-ethyl carbonate .................. 22.40%
OTHER INGREDIENTS:. . . . . . . . . . . . . . . . . . . . . . . . . . . 77.60%
MOVENTO contains 2.00 pounds       TOTAL: 100.00%
spirotetramat per U.S. gallon (240 grams AI/liter)
EPA Reg. No. 264-1050

KEEP OUT OF REACH OF CHILDREN
CAUTION
For MEDICAL And TRANSPORTATION Emergencies ONLY Call
24 Hours A Day 1-800-334-7577
For PRODUCT USE Information Call 1-866-99BAYER (1-866-992-2937)
Please refer to booklet for additional precautionary
statements and directions for use.
Produced for
Bayer CropScience LLC
800 N. Lindbergh Blvd.
St. Louis, MO 63167
MOVENTO is a registered trademark of Bayer.
©2026 Bayer Group. All rights reserved.

COPY AREA
COPY AREA

1
FIRST AID
If on skin
or clothing:
• Take off contaminated clothing.
• Rinse skin immediately with plenty of water for 15 to 20 minutes.
• Call a poison control center or doctor for treatment advice.
If swallowed: • Call a poison control center or doctor immediately for treatment advice.
• Have person sip a glass of water if able to swallow.
• Do not induce vomiting unless told to do so by a poison control center or
doctor.
• Do not give anything by mouth to an unconscious person.
If in eyes: • Hold eye open and rinse slowly and gently with water for 15-20
minutes.
• Remove contact lenses, if present, after the first five minutes, then
continue rinsing.
• Call a poison control center or doctor immediately for treatment advice.
Have a product container or label with you when calling a poison control center
or doctor, or going for treatment. You may also contact 1-800-334-7577 for
emergency medical treatment information.
Note to Physician: No specific antidote is available.  Treat the patient symptomatically.
PRECAUTIONARY STATEMENTS
HAZARDS TO HUMANS AND DOMESTIC ANIMALS
CAUTION
• Harmful if swallowed or absorbed through skin.
• Causes moderate eye irritation.
• Avoid contact with skin, eyes, or clothing.
• Wash thoroughly with soap and water after handling and before eating, drinking,
chewing gum, or using tobacco.

2
• Prolonged or frequently repeated skin contact may cause allergic reactions in some individuals.
PERSONAL PROTECTIVE EQUIPMENT (PPE)
Follow manufacturer’s instructions for cleaning/maintaining PPE. If no such instructions for
washables, use detergent and hot water. Keep and wash PPE separately from other laundry.
Applicators and other handlers must wear:
• Long-sleeved shirt and long pants.
• Chemical resistant gloves made of barrier laminate, butyl rubber ≥ 14 mils, nitrile rubber ≥ 14
mils, natural rubber ≥ 14 mils, polyethylene, polyvinyl chloride ≥ 14 mils, or viton ≥ 14 mils.
• Shoes plus socks.
ENGINEERING CONTROLS
When handlers use closed systems, or enclosed cabs in a manner that meets the
requirements listed in the Worker Protection Standard (WPS) for agricultural pesticides
[40 CFR 170.240 (d)(4-6)], the handler PPE requirements may be reduced or modified as
specified in the WPS.
USER SAFETY RECOMMENDATIONS
• Users should wash hands before eating, drinking, chewing gum, using tobacco, or using the toilet.
• Users should remove clothing/PPE immediately if pesticide gets inside. Then wash
thoroughly and put on clean clothing.
• Users should remove PPE immediately after handling this product.
USER SAFETY REQUIREMENTS
Follow manufacturer’s instructions for cleaning/maintaining PPE.  If no such instructions for
washables exist, use detergent and hot water.  Keep and wash PPE separately from other laundry.
ENVIRONMENTAL HAZARDS
For Terrestrial Use: This pesticide is toxic to aquatic invertebrates and oysters. Do not apply

3
directly to water, to areas where surface water is present, or to intertidal areas below the mean
high water mark.  This product may contaminate water through drift of spray in wind.  Do not
apply when weather conditions favor drift from treated areas.  Drift and runoff from treated
areas may be hazardous to aquatic organisms in neighboring areas.  Do not contaminate
water when disposing of equipment washwaters or rinsate.
This chemical has properties and characteristics associated with chemicals detected in
ground water.  The use of this chemical in areas where soils are permeable, particularly where
the water table is shallow, may result in ground-water contamination.
This product is potentially toxic to honey bee larvae through residues in pollen and nectar, but
not to adult honeybees.  Exposure of adult bees to direct treatment or residues on blooming
crops can lead to effects on honeybee larvae.  See the “Directions for Use” section of this label
for specific crop application instructions that minimize risk to honey bee larvae.
Runoff Management
This product may contaminate water through runoff or drift of spray in wind.  This product
has a high potential for runoff for several weeks after application. Poorly draining soils and
soils with shallow water tables are more prone to produce runoff that contains this product.
A level well maintained vegetative buffer strip between areas to which this product is applied
and surface water features such as ponds, streams, and springs will reduce the potential for
contamination of water from rainfall runoff.  Runoff of this product will be reduced by avoiding
applications when rainfall is forecasted to occur within 48 hours.
Endangered Species Advisory/Protection Requirements
The use of any pesticide in a manner that may kill or otherwise harm endangered species or
adversely modify their habitat is a violation of Federal law.
CONDITIONS OF SALE AND LIMITATIONS OF WARRANTY AND LIABILITY
Read the entire Directions for Use, Conditions, Disclaimer of Warranties and Limitations of
Liability before using this product.  If terms are not acceptable, return the unopened product
container at once.

4
By using this product, user or buyer accepts the following Conditions, Disclaimer of Warranties
and Limitations of Liability.
CONDITIONS: The directions for use of this product are believed to be adequate and must
be followed carefully. However, it is impossible to eliminate all risks associated with the use
of this product.  Crop injury, ineffectiveness or other unintended consequences may result
because of such factors as weather conditions, presence of other materials, or the manner
of use or application, all of which are beyond the control of Bayer CropScience.  To the
extent consistent with applicable law, all such risks shall be assumed by the user or buyer.
DISCLAIMER OF WARRANTIES: TO THE EXTENT CONSISTENT WITH APPLICABLE LAW,
BAYER CROPSCIENCE MAKES NO OTHER WARRANTIES, EXPRESS OR IMPLIED, OF
MERCHANTABILITY OR OF FITNESS FOR A PARTICULAR PURPOSE OR OTHERWISE,
THAT EXTEND BEYOND THE STATEMENTS MADE ON THIS LABEL. No agent of Bayer
CropScience is authorized to make any warranties beyond those contained herein or to
modify the warranties contained herein. TO THE EXTENT CONSISTENT WITH APPLICABLE
LAW, BAYER CROPSCIENCE DISCLAIMS ANY LIABILITY WHATSOEVER FOR SPECIAL,
INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OR HANDLING
OF THIS PRODUCT.
LIMITATIONS OF LIABILITY: TO THE EXTENT CONSISTENT WITH APPLICABLE LAW, THE
EXCLUSIVE REMEDY OF THE USER OR BUYER FOR ANY AND ALL LOSSES, INJURIES OR
DAMAGES RESULTING FROM THE USE OR HANDLING OF THIS PRODUCT, WHETHER IN
CONTRACT, WARRANTY, TORT, NEGLIGENCE, STRICT LIABILITY OR OTHERWISE, SHALL
NOT EXCEED THE PURCHASE PRICE PAID, OR AT BAYER CROPSCIENCE’S ELECTION,
THE REPLACEMENT OF PRODUCT.
DIRECTIONS FOR USE
It is a violation of Federal law to use this product in a manner inconsistent with its labeling.
Read the entire label before using this product.
Do not apply this product in a way that will contact workers or other persons, either directly or

5
through drift.  Only protected handlers may be in the area during application. For any requirements
specific to your State or Tribe, consult the agency responsible for pesticide regulation.
AGRICULTURAL USE REQUIREMENTS
Use this product only in accordance with its labeling and with the Worker Protection Standard,
40 CFR part 170. This Standard contains requirements for the protection of agricultural workers
on farms, forests, nurseries, and greenhouses, and handlers of agricultural pesticides. It
contains requirements for training, decontamination, notification, and emergency assistance.
It also contains specific instructions and exceptions pertaining to the statements on this
label about personal protective equipment (PPE), notification to workers, and restricted-entry
interval. The requirements in this box only apply to uses of this product that are covered by
the Worker Protection Standard.
Do not enter or allow worker entry into treated areas during the restricted entry interval (REI)
of 24 hours following application.
PPE required for early entry to treated areas (that is permitted under the Worker Protection
Standard and that involves contact with anything that has been treated, such as plants,
soil, or water), is:
• Coveralls.
• Chemical resistant gloves made of barrier laminate, butyl rubber ≥ 14 mils, nitrile rubber ≥ 14
mils, natural rubber ≥ 14 mils, polyethylene, polyvinyl chloride ≥ 14 mils, or viton ≥ 14 mils.
• Shoes plus socks.
PRODUCT INFORMATION
MOVENTO®:
• Is a suspension concentrate formulation and is active primarily by ingestion against
immature target pest life stages. In addition, fertility of adult female target pests, such as
aphids and whiteflies, may be reduced.
• Can be applied by air, ground equipment or through chemigation as a preventative
treatment or timed to coincide with an early threshold level in developing insect
populations.
• Must be tank-mixed with a spray adjuvant / additive having spreading and penetrating
properties to maximize leaf uptake and systemicity of the active ingredient within treated

6
plants; please contact your local Bayer CropScience representative or PCA for specific
recommendations by crop.
• It is widely known that tank mixtures and/or sequential treatments of horticultural spray oil with
Captan and/or sulfur may cause adverse plant compatibility in tree and vine crops; including
MOVENTO in this tankmix and/or sequential treatment scenario is not recommended.
• Following application to plant foliage, MOVENTO is fully systemic, moving through phloem
and xylem to new shoot, leaf and root tissues; systemicity and efficacy may be hindered
during periods of cold temperatures, under drought conditions, or when plants are not
actively growing.
APPLICATION INSTRUCTIONS
• Foliar spray applications must be made using properly calibrated ground sprayers, fixed- or
rotary-winged aircraft or through properly designed, sprinkler-type, chemigation equipment
(See Chemigation Application section). Sufficient spray volume, based on the size and
density of the treated crop, must be utilized that allows for good coverage of both young
and old foliage without runoff or collection of spray solution on leaf margins, fruit, or other
plant tissues. For optimum control of target pests on tree and vine crops, treating both
sides of the plant during the same application period is recommended; for practices such as
alternate row middles or tops and bottoms, both sides of the trees or vines must be treated
within a 72-hour period. Good coverage will help ensure maximum uptake by leaf surfaces
and optimum systemicity within the plant.
° Ground applications must be made in a minimum of 50 gallons per acre on tree and vine
crops; 15 gallons of water per acre on potato and vegetable crops.
° Aerial applications must be made in a minimum of 10 gallons of water per acre in tree
and vine crops, and 5 gallons of water per acre in vegetable, and potato crops. The
higher dosage of MOVENTO within the crop/pest-specific section may be necessary for
optimum control for aerial applications.
USE RESTRICTIONS
• Do not use in enclosed structures, such as greenhouses or planthouses.
• For annual crops where multiple plantings can occur within a calendar year, do not apply

7
more than 30 fl oz/A, which is 0.47 lb spirotetramat/A within a calendar year unless specified
otherwise within a crop-specific section for a given crop.
• Sufficient leaf tissue must be present for uptake and translocation of this product; due to this
requirement, do not apply prior to petal-fall on pome fruits, stone fruits, and tree nut crops.
• The use of Induce® adjuvant in combination with MOVENTO on grape, pome fruits, and stone fruits
is prohibited when fruit is present due to adverse plant compatibility on harvested commodities.
• Do not apply when winds are greater than 15 mph and avoid gusty and windless conditions.
Refer to the specific use directions and restrictions in each Crop, Crop Group or Crop
Subgroup table.
INSECT RESISTANCE MANAGEMENT RECOMMENDATIONS
MOVENTO contains an active ingredient with a mode of action classified as a
Group 23 Insecticide, i.e., a lipid biosynthesis inhibitor (LBI). To delay insecticide resistance:
• Some insects are known to develop resistance to insecticides after repeated use. As with
any insecticide, the use of this product should conform to resistance management strategies
established for the use area.
• Bayer CropScience strongly encourages that MOVENTO, applied alone or in tankmix
combination with another Group 23 product, be applied in a block rotation or windowed
approach with products from other chemical classes having a different mode of action
before using additional applications of Group 23 insecticides against the same target pest.
Using a block rotation or windowed approach, along with other IPM practices, is considered
an effective use strategy for preventing or delaying an insect pest’s ability to develop
resistance to a given class of chemistry.
Contact your local extension specialist, certified crop advisor, and/or Bayer CropScience
representative for additional resistance management or IPM recommendations. Also, for more
information on Insect Resistance Management (IRM), visit the Insecticide Resistance Action
Committee (IRAC) on the web at http://irac-online.org.

8
CHEMIGATION - VEGETABLE AND POTATO CROPS ONLY
Types of irrigation systems
Apply this product only through:
• Sprinkler type irrigation systems only.
• These types include:  center pivot, lateral move, side roll, or overhead solid set irrigation systems.
• Do not apply MOVENTO through any other type of irrigation system.
• Do not apply when wind speed favors drift beyond the area intended for treatment.
Uniform water distribution and system calibration
The irrigation system must provide uniform distribution of treated water. Crop injury, lack of
effectiveness, or illegal pesticide residues in the crop can result from non-uniform distribution
of treated water. The chemigation system must be calibrated to uniformly apply the rates
specified in crop-specific label sections. If you have questions about calibration, contact your
Cooperative Extension Service agent, equipment manufacturers, or other experts.
Chemigation monitoring
A person knowledgeable of the chemigation system and responsible for its operation, or under
the supervision of the responsible person, shall shut the system down and make necessary
adjustments should the need arise.
Required system safety devices
The system must contain a functional check valve, vacuum relief valve, and low-pressure drain
appropriately located on the irrigation pipeline to prevent water source contamination from
backflow. The pesticide injection pipeline must contain a functional, automatic, quick-closing
check valve to prevent the flow of fluid back toward the injection pump. The pesticide injection
pipeline must also contain a functional, normally closed, solenoid-operated valve located on the
intake side of the injection pump and connected to the system interlock to prevent fluid from being
withdrawn from the supply tank when the irrigation system is either automatically or manually
shut down. The system must contain functional interlocking controls to automatically shut off the
pesticide injection pump when the water pump motor/engine stops or in cases where there is no
water pump, when water pressure decreases to the point where pesticide distribution is adversely

9
affected. The irrigation line or water pump must include a functional pressure switch, which will
stop the water pump motor when the water pressure decreases to the point where pesticide
distribution is adversely affected. Systems must use a metering pump, such as a positive
displacement injection pump (e.g. diaphragm pump) effectively designed and constructed of
materials that are compatible with pesticides and capable of being fitted with a system interlock.
Using water from public water systems
Do not connect an irrigation system (including greenhouse system) used for pesticide
application to a public water system unless the pesticide label-prescribed safety devices for
public water systems are in place. Public water system means a system for the provision
to the public of piped water for human consumption if such system has at least 15 service
connections or regularly serves an average of at least 25 individuals daily at least 60 days
out of the year. Chemigation systems connected to public water systems must contain a
functional, reduced-pressure zone, back-flow preventer (RPZ) or the functional equivalent in
the water supply line upstream from the point of pesticide introduction. As an option to the
RPZ, the water from the public water system should be discharged into a reservoir tank prior
to pesticide introduction. There shall be a complete physical break (air gap) between the outlet
end of the fill pipe and the top or overflow rim of the reservoir tank of at least twice the inside
diameter of the fill pipe. The pesticide injection pipeline must contain a functional automatic
quick-closing check valve to prevent the flow of fluid back toward the injection pump. The
pesticide injection pipeline must contain a functional normally closed solenoid-operated
valve located on the intake side of the injection pump and connected to the system interlock
to prevent fluid from being withdrawn from the supply tank when the irrigation system is
either automatically or manually shut down. The system must contain functional interlocking
controls to automatically shut off the pesticide injection pump when the water pump motor
stops or in cases where there is no water pump, when the water pressure decreases to the
point where pesticide distribution is adversely affected. Systems must use a metering pump
such as a positive displacement injection pump (e.g. diaphragm pump) effectively designed
and constructed of materials that are compatible with pesticides and capable of being fitted
with a system interlock.

10
Injection for chemigation
Inject the specified dosage of MOVENTO into the irrigation main water stream: (1) through
a constant flow, metering device; (2) into the center of the main line flow via a pitot tube or
equivalent; (3) at a point ahead of at least one, right-angle turn in the main stream flow such
that thorough mixing with the irrigation water is ensured.
Center-pivot and automatic-move linear systems
Inject the specified dosage per acre continuously for one complete revolution (center pivot) or
move of the system.  The system should be run at maximum speed.  It is recommended that
nozzles in the immediate area of control panels, chemical supply tanks, pumps, and system
safety devices be plugged to prevent chemical contamination of these areas.  The use of END
GUNS is NOT RECOMMENDED.  End guns that provide uneven distribution of treated water
can result in lack of effectiveness or illegal pesticide residues in or on the crop.
Solid set and manually controlled linear systems
Injection should be during the last 30 to 60 minutes of regular irrigation period or as a separate
30 to 60 minute application not associated with a regular irrigation.
Chemigation Application Instructions
Chemigation applications must be made as concentrated as possible. For best results apply
at 100% input/travel speed, for center pivots or 0.1 inch (2,716 gallons) up to 0.15 inch
(4,073 gallons) of water/A, for other systems. The higher dosage of MOVENTO within the
crop-specific/pest section may be necessary for optimum control for chemigation applications.
Flushing and Cleaning the chemical injection system
At the end of the application period, allow time for all lines to flush the pesticide through all
nozzles or emitters before turning off irrigation water.  To ensure the lines are flushed and free of
pesticides, a dye indicator may be injected into the lines to mark the end of the application period.
In order to apply pesticides accurately, the chemical injection system must be kept clean, free of
chemical or fertilizer residues and sediments. Refer to your owner’s manual or ask your equipment
supplier for the cleaning procedure for your injection system.

11
SPRAY DRIFT MANAGEMENT
Do not apply when wind speed favors drift beyond the area intended for treatment. The
interaction of many equipment and weather related factors determine the potential for spray
drift. The applicator is responsible for considering all of these factors when making application
decisions. Avoiding spray drift is the responsibility of the applicator.
Droplet Size
An important factor influencing drift is droplet size. Select nozzles and pressure that deliver
medium spray droplets as indicated in nozzle manufacturer’s catalogs and in accordance
with ASAE Standard S-572. Nozzles that deliver coarse spray droplets may be used to reduce
spray drift provided spray volume per acre (GPA) is increased to maintain crop coverage. For
aerial application, spray should be released at the lowest possible height consistent with good
pest control and flight safety. Applications more than 10 feet above the crop canopy should be
avoided. Low humidity and high temperature increase the evaporation rate of spray droplets
and therefore the likelihood of spray drift to aquatic areas. Avoid spraying during conditions of
low humidity and/or high temperature.
Wind Speed
Drift potential increases at wind speeds of less than 3 mph (due to inversion potential) or
more than 10 mph. However, many factors, including droplet size, canopy and equipment
specifications determine drift potential at any given wind speed. Do not apply when winds are
greater than 15 mph and avoid gusty and windless conditions. Avoiding applications when
wind direction is toward an aquatic area can reduce risk exposure to sensitive aquatic areas.
Temperature Inversions
Do not make aerial or ground applications during temperature inversions. Drift potential
is high during temperature inversions. Temperature inversions restrict vertical air mixing,
which causes small-suspended droplets to remain close to the ground and move laterally in
a concentrated cloud. Temperature inversions are characterized by increasing temperature
with altitude and are common on nights with limited cloud cover and light to no wind. They
begin to form as the sun sets and often continue into the morning. Their presence can
be indicated by ground fog. However, if fog is not present, the movement of smoke from
a ground source can also identify inversions. Smoke that layers and moves laterally in a

12
concentrated cloud (under low wind conditions) indicates an inversion, while smoke that
moves upward and rapidly dissipates indicates good vertical air mixing.
Airblast (Air Assist) Applications for Tree Crops and Vineyards
Airblast sprayers carry droplets into the canopy of trees/vines via a radial, or lateral directed
air stream. The following drift management practices should be followed:
• Adjust deflectors and aiming devices so that spray is only directed into the canopy;
• Block off upward pointed nozzles when there is no overhanging canopy;
• Use enough air volume to penetrate the canopy and provide good coverage;
• Do not allow the spray to go beyond the edge of the cultivated area (i.e., turn off sprayer
when turning at end rows);
• For applications to the outside rows, only spray inward, toward the orchard/grove.
Aerial Applications
• Mount the spray boom on the aircraft so as to minimize drift caused by wing tip vortices.
• The minimum practical boom length should be used, and should not exceed 75% of the wing
span or rotor diameter.
• Applications should not be made at a height greater than 10 feet above the top of the largest
plants unless a greater height is required for aircraft safety.
COMPATIBILITY TESTING AND TANK MIX PARTNERS
It is the pesticide user’s responsibility to ensure that all products are registered for the intended
use. Read and follow the applicable restrictions and limitations and directions for use on all
product labels involved in tank mixing. Users must follow the most restrictive directions for
use and precautionary statements of each product in the tank mixture.
• When considering mixing MOVENTO with other pesticides, or other additives, first contact
your supplier for advice.
• For further information, contact your local Bayer representative.
• If your supplier and Bayer representative have no experience with the combination you are
considering, you should conduct a test to determine physical compatibility.

13
• To determine physical compatibility, add the recommended proportions of each chemical
with the same proportion of water, as will be present in the chemical supply tank, into a
suitable container, mix thoroughly and allow to stand for five minutes. If the combination
remains mixed, or can be readily re-mixed, the mixture is considered physically compatible.
Compatibility
MOVENTO is physically and biologically compatible with many registered pesticides and
fertilizers or micronutrients. However, it is known that many components, including crop
protection products, fertilizers, micronutrients, and spray adjuvants, may be present in a
tank mix combination. There is potential for  adverse chemical reactions.  It is impossible
to determine physical, biological, and plant compatibility for all scenarios that may be
encountered; therefore, it is recommended that users determine the chemical, physical,
biological and plant compatibility of such mixes prior to making applications on a broad
commercial scale. Observe the most restrictive of the labeling instructions and precautions
of all products used in mixtures.
Order of Mixing
The proper mixing procedure for MOVENTO alone or in tank mix combinations with other
pesticides is:
1. Fill the spray tank 1/4 to 1/3 full with clean water;
2. While recirculating and with the agitator running, add any products in Polyvinyl acetate
(PVA) bags (See Note). Allow time for thorough mixing;
3. Continue to fill spray tank with water until 1/2 full;
4. Add any other wettable powder (WP) or wettable granules (WG) products;
5. Add the required amount of MOVENTO, and any other “flowable” (FL or SC) type products;
add required amount of MOVENTO, and;
6. Allow enough time for thorough mixing of each product added to tank;
7. If applicable, add any remaining tank mix components: emulsifiable concentrates (EC),
fertilizers and micronutrients;
8. Fill spray tank to desired level and maintain constant agitation to ensure uniformity of
spray mixture.

14
NOTE: Do not use PVA packets in a tank mix with products that contain boron or release
free chlorine. The resultant reaction of PVA and boron or free chlorine is a plastic that is not
soluble in water or solvents. For tank mixing with MOVENTO, WSP packaged product user
must carefully follow the label directions provided on those product labels.
ROTATIONAL CROPS
MOVENTO is labeled for use on the following crops:
Banana And Plantain, Brassica (Cole) Leafy Vegetables (crop group 5), Bulb Vegetables
(crop group 3-07A & 3-07B), Bushberry and Low Growing Berry (Crop Subgroups
13-07B and 13-07H), Carrot, Christmas Tree Plantations, Citrus Fruits (crop group 10-10),
Coffee, Fruiting Vegetables (crop group 8-10), Globe Artichoke, Hops, Leafy Vegetables
(except Brassica) (crop group 4), Legume Vegetables (except Soybean, dry) (crop group
6), Pineapple, Pome Fruits (crop group 11-10), Pomegranate, Potato And Other Tuberous
And Corm Vegetables (crop group 1C), Small Fruit Vine Climbing Subgroup (except Fuzzy
Kiwifruit) (crop group 13-07F), Soybean, Stone Fruits (crop group 12-12), Sugar beet, Tree
Nuts (crop group 14-12), Tropical Fruits, and Watercress.
ROTATIONAL CROPS (continued)
• Treated areas may be replanted with any crop specified on this label, or any crop for
which a tolerance exists for the active ingredient, as soon as practical following the last
application.
• Do not plant or replant any crop not listed on this label within 30 days after the last
application except watercress, which has a 260-day plant-back interval (PBI).
SPECIFIC CROP DIRECTIONS
CROP USE DIRECTIONS
Apply specified dosage of MOVENTO early in the infestation as the population begins to
develop or at early threshold for the target insect pest. Apply higher dosages specified

15
within the crop specific sections when applied as a preventive application, for moderate
to heavy insect pressure, or where longer residual control is desired. Degree of efficacy
against labeled pests will be determined, in part, by the stage of pest development at
application and infestation level of those pests.
Apply in adequate water for uniform coverage. For tree and vine crops, apply in a
minimum of 50 GPA for conventional ground airblast sprayer, 30 GPA for high air velocity,
low volume or air curtain sprayers, 10 GPA for aerial application; rates for tree and vine
crops are based on full-size mature trees and vines. For vegetable and potato crops,
apply in a minimum of 15 GPA by ground and 5 GPA by aerial application. MOVENTO may
also be applied through overhead irrigation systems as designated in the CHEMIGATION
section of this label under Chemigation Application Instructions.
MOVENTO must be tank-mixed with a spray adjuvant / additive having spreading and
penetrating properties to maximize leaf uptake and systemicity of the active ingredient
within treated plants; please contact your local Bayer CropScience representative or
PCA for specific recommendations by crop. However, the use of Induce ® adjuvant
in combination with MOVENTO on grape, pome fruits, and stone fruits is prohibited
when fruit is present due to adverse plant compatibility on harvested commodities. The
tank-mixture of MOVENTO with an adjuvant / additive having sticking properties or crop
protection product formulations containing built-in stickers have been shown to interfere
with leaf uptake and should be avoided. Sufficient leaf tissue must be present for uptake
and translocation of this product; due to this requirement, do not apply prior to petal-fall
on pome fruits, stone fruits, and tree nut crops.
It is widely known that tank mixtures and/or sequential treatments of horticultural spray
oil with Captan and/or sulfur may cause adverse plant compatibility in tree and vine
crops; including MOVENTO in this tank mix and/or sequential treatment scenario is not
recommended.

16
BANANA and PLANTAIN (HI, PR, FL only)
Pests Controlled Product Rate

Aphids
(fl oz/A) (lb ai/A)
10.0 - 16.0 0.16 -
0.25
Foliar Application Restrictions:
Pre-Harvest Interval (PHI): 1 day(s)
Minimum interval between applications: 14 days
Maximum MOVENTO allowed per crop season: 80 fl oz/A
Maximum spirotetramat per crop season: 1.25 lb ai/A

17
BRASSICA (COLE) LEAFY VEGETABLES
Crops of Crop Group 5 Including: Broccoli, Broccoli raab (rapini), Brussels sprouts,
Cabbage, Cauliflower, Cavalo broccolo, Chinese broccoli (gai lon), Chinese cabbage
(bok choy), Chinese cabbage (napa), Chinese mustard cabbage (gai choy), Collards,
Kale, Kohlrabi, Mizuna, Mustard greens, Mustard spinach, Rape greens
Pests Controlled Product Rate
Aphids
Swede midge
Whiteflies
 (fl oz/A) (lb ai/A)
4.0 – 5.0 0.06 -
0.08
Pests Suppressed
Diamondback moth
Nematodes
Onion thrips (larvae)
Foliar Application Restrictions:
Pre-Harvest Interval (PHI): 1 day(s)
Minimum interval between applications: 7 days
Maximum MOVENTO allowed per crop season:  10 fl oz/A
Maximum spirotetramat allowed per crop season: 0.16 lb ai/A
Certain nonionic and organosilicone adjuvants, which may potentially be used with
MOVENTO, have caused intolerable damage to bok choy, napa, mustard spinach,
mizuna, and mustard greens when applied alone, in the absence of MOVENTO.
Testing has shown that MOVENTO does not increase the potential for damage when
used in combination with such adjuvants. Due to the wide variety and composition
of spray adjuvants that may be used in combination with MOVENTO, only use a
spreading-penetrating adjuvant that is known to be safe to the target crop.

18
BULB VEGETABLES
Crops of Crop SubGroup 3-07A Including: Daylily (bulb), Fritillaria (bulb), Garlic (bulbs
of common, great-headed, Serpent), Lily (bulb), Onion (bulbs of common, Chinese,
Pearl, potato onion), Shallot (bulb), plus cultivars, varieties, and/or hybrids of these.
Crops of Crop Subgroup 3-07B Including: Chinese Chive (fresh leaves), Chive (fresh
leaves), Elegans hosta, Fritillaria (leaves), Kurrat, Leek (Allium porrum, Lady’s, Wild),
Onion (Beltsville bunching, fresh, green, macrostem, tree [tops], Welsh [tops]), Shallot
(fresh leaves), plus cultivars, varieties, and/or hybrids of these.
Pests Controlled Product Rate
Onion thrips (larvae)  (fl oz/A) (lb ai/A)
5.0 0.08
Foliar Application Restrictions:
Pre-Harvest Interval (PHI): 3 day(s) (members of Subgroup 3-07A); 7 days (members of
Subgroup 3-07B)
Minimum interval between applications: 7 days
Maximum MOVENTO allowed per crop season: 10 fl oz/A
Maximum spirotetramat per crop season: 0.16 lb ai/A
For Onions, Leeks, and Chives grown for seed production, do not apply 4 months prior to
bloom, during bloom or until after petal fall.

19
BUSHBERRY SUBGROUP
LOW GROWING BERRY SUBGROUP
Crops of Crop Subgroups 13-07B and 13-07H Including: Aronia berry, Bearberry,
Bilberry, Blueberry (highbush and lowbush), Chilean guava, Cloudberry, Cranberry,
Currant (black, buffalo, native, and red), Elderberry, European barberry, Gooseberry,
Edible honeysuckle, Jostaberry, Juneberry, Muntries, Lingonberry, Partridgeberry, Salal,
Sea buckthorn, and cultivars, varieties, and/or hybrids of these.
Pests Controlled Product Rate
Aphids
Blueberry Gall Midge
Cranberry Tipworm
Thrips (larvae)
(fl oz/A) (lb ai/A)
8.0 - 10.0 0.13 - 0.16
Pests Suppressed Product Rate
Blueberry Maggot
Leafhoppers
(fl oz/A) (lb ai/A)
10.0 0.16
Foliar Application Restrictions:
Pre-Harvest Interval (PHI): 7 days
Minimum interval between applications: 7 days
Maximum MOVENTO allowed per calendar year: 30 fl oz/A
Maximum spirotetramat per crop season: 0.47 lb ai/A
Do not apply until after petal fall

20
CARROT
Pests Controlled Product Rate
Aphids
Whiteflies
(fl oz/A) (lb ai/A)
5.0 0.08
Foliar Application Restrictions:
Pre-Harvest Interval (PHI): 1 day
Minimum interval between applications: 7 days
Maximum MOVENTO allowed per crop season: 10 fl oz/A
Maximum spirotetramat per crop season: 0.16 lb ai/A
CHRISTMAS TREE PLANTATIONS
Pests Controlled Product Rate
Aphids (including root aphids and Adelgids)
Scales
(fl oz/A) (lb ai/A)
5.0 – 10.0 0.08 - 0.16
Foliar Application Restrictions:
Minimum interval between applications: 14 days
Maximum MOVENTO allowed per calendar year: 20 fl oz/A
Maximum spirotetramat per calendar year: 0.31 lb ai/A

21
CITRUS FRUITS
Crops of Crop Group 10-10 Including:  Australian lime (desert, finger, and round), Brown River
finger lime, Calamondin, Citron, Grapefruit, Japanese summer grapefruit, Kumquat, Lemon,
Lime, Mediterranean mandarin, Mount White lime, New Guinea wild lime, Orange (sour and
sweet), Pummelo, Russell River lime, Satsuma mandarin, Sweet lime, Tachibana orange, Tahiti
lime, Tangelo, Tangerine, Tangor, Trifoliate orange, Uniq fruit, including cultivars, varieties and/or
hybrids of these commodities.
Pests Controlled Product Rate
Aphids
Asian citrus psyllid
California red scale
Citrus leafminer
Citrus bud mite
Citrus red mite
Citrus rust mite (silver mite)
Citrus snow scale
Citrus thrips
Florida red scale
Mealybugs
Pink citrus rust mite
Purple scale
Texas citrus mite
Whiteflies
(fl oz/A) (lb ai/A)
8.0 – 10.0 0.13 - 0.16
Pests Suppressed
Black scale
Brown scale
Citricola scale
Cottony cushion scale
Nematodes
Foliar Application Restrictions:
Pre-Harvest Interval (PHI): 1 day(s)
Minimum interval between applications: 21 days
Maximum MOVENTO allowed per calendar year: 20 fl oz/A
Maximum spirotetramat per calendar year: 0.31 lb ai/A
Do not apply this product within 10 days prior to bloom, during bloom, or until petal fall is complete.
For production areas in Alabama, Florida, Georgia, Louisiana, Mississippi, South Carolina,
and Texas, optimum control of target pests is obtained at application volumes up to 250 gpa;
application volumes in excess of 350 gpa must be avoided.
Do not apply non-ionic surfactants in tank mix combination with MOVENTO on white grapefruit.

22
COFFEE
Pests Controlled Product Rate
Green Scale (fl oz/A) (lb ai/A)
8.0 - 10.0 0.13 – 0.16
Foliar Application Restrictions:
Pre-Harvest Interval (PHI): 14 day(s)
Minimum interval between applications: 21 days
Maximum MOVENTO allowed per calendar year: 30 fl oz/A
Maximum spirotetramat per calendar year: 0.47 lb ai/A

23
FRUITING VEGETABLES
Crops of Crop Group 8-10 Including: African eggplant, Bush tomato, Cocona, Currant tomato,
Eggplant, Garden huckleberry, Goji berry, Groundcherry, Martynia, Naranjilla, Okra, Pea
eggplant, Pepino, Pepper (bell and nonbell*), Roselle, Scarlet eggplant, Sunberry, Tomatillo,
Tomato, Tree tomato, including cultivars, varieties and/or hybrids of these commodities.
*including cayenne, chili pepper, habanero, jalapeno, pablano, pimento, and serrano.
Pests Controlled Product Rate
Aphids
Broad mite
Psyllids
Tomato russet mite
Whiteflies
(fl oz/A) (lb ai/A)
4.0 – 5.0 0.06 - 0.08Pests Suppressed
Leafminers
Nematodes
Twospotted spider mite
Western flower thrips (larvae)
Foliar Application Restrictions:
Pre-Harvest Interval (PHI): 1 day(s)
Minimum interval between applications: 7 days
Maximum MOVENTO allowed per crop season: 10 fl oz/A
Maximum spirotetramat per crop season: 0.16 lb ai/A

24
GLOBE ARTICHOKE
Pests Controlled Product Rate
Aphids
(fl oz/A) (lb ai/A)
5.0 - 8.0 0.08 –
0.13
Foliar Application Restrictions:
Pre-Harvest Interval (PHI): 3 day(s)
Minimum interval between applications: 7 days
Maximum MOVENTO allowed per crop season: 32 fl oz/A
Maximum spirotetramat per crop season: 0.5 lb ai/A
HOPS
Pests Controlled Product Rate
Hop aphid
Twospotted spider mite
(fl oz/A) (lb ai/A)
5.0 – 6.0 0.08 - 0.09
Foliar Application Restrictions:
Pre-Harvest Interval (PHI): 7 day(s)
Minimum interval between applications: 14 days
Maximum MOVENTO allowed  per  calendar year:  12.5 fl oz/A
Maximum spirotetramat per calendar year: 0.2 lb ai/A

25
LEAFY VEGETABLES (Except Brassica Vegetables)
Crops of Crop Group 4 Including: Amaranth (leafy amaranth, Chinese spinach, tampala),
Arugula (Roquette), Cardoon, Celery, Celtuce, Chervil, Chinese celery, Chrysanthemum
(edible-leaved and garland), Corn salad, Cress (garden), Cress (upland, yellow rocket,
winter cress), Dandelion, Dock (sorrel), Endive (escarole), Florence fennel (Finocchio),
Lettuce (head and leaf), Orach, Parsley, Purslane (garden and winter), Radicchio (red
chicory), Rhubarb, Spinach [including New Zealand and vine (Malabar spinach, Indian
spinach)], Swiss chard, Taro leaves
Pests Controlled Product Rate
Aphids
Whiteflies
(fl oz/A) (lb ai/A)
4.0 – 5.0 0.06 - 0.08
Pests Suppressed
Diamondback moth
Leafminers
Nematodes
Western flower thrips (larvae)
Foliar Application Restrictions:
Pre-Harvest Interval (PHI): 3 day(s)
Minimum interval between applications: 7 days
Maximum MOVENTO allowed per crop season: 10 fl oz/A
Maximum spirotetramat per crop season: 0.16 lb ai/A

26
LEGUME VEGETABLES
Crops of Crop Group 6 (except soybean, dry) Including: Edible Podded and Succulent
Shelled Pea and Bean and Dried Shelled Pea and Bean
Bean (Lupinus spp., including grain lupin, sweet lupin, white lupin, and white sweet lupin)
Bean (Phaseolus spp., including field bean, kidney bean, lima bean, navy bean, pinto
bean, runner bean, snap bean, tepary bean, wax bean)
Bean (Vigna spp., including adzuki bean, asparagus bean, blackeyed pea, catjang,
Chinese longbean, cowpea, Crowder pea, moth bean, mung bean, rice bean, Southern
pea, urd bean, yardlong bean)
Pea (Pisum spp. including dwarf pea, edible-pod pea, English pea, field pea, garden pea,
green pea, snow pea, sugar snap pea)
Other Beans and Peas (Broad bean (fava), Chickpea (garbanzo bean), Guar, Jackbean,
Lablab bean (hyacinth bean), Lentil, Pigeon pea, soybean (immature seed), Sword bean)
Pests Controlled Product Rate
Aphids
Whiteflies
(fl oz/A) (lb ai/A)
4.0 - 5.0 0.06 - 0.08
Pests Suppressed
Leafminers
Melon thrips (larvae)
Nematodes
Twospotted spider mite
Western flower thrips (larvae)

27
Foliar Application Restrictions:
Pre-Harvest Interval (PHI): 1 day(s) (edible podded and succulent beans and peas);
7 day (dry shelled beans and peas).
Minimum interval between applications: 7 days
Maximum MOVENTO allowed per crop season: 10 fl oz/A
Maximum spirotetramat per crop season: 0.16 lb ai/A
PINEAPPLE
Pests Controlled Product Rate
Mealybugs  (fl oz/A) (lb ai/A)
10.0  0.16
Foliar Application Restrictions:
Pre-Harvest Interval (PHI): 1 day(s)
Minimum interval between applications: 14 days
Maximum MOVENTO allowed per crop season:  20 fl oz/A
Maximum spirotetramat per crop season: 0.31 lb ai/A

28
POME FRUITS
Crops of Crop Group 11-10 Including: Apple, Asian pear, Azarole, Chinese quince,
Crabapple, Japanese quince, Loquat, Mayhaw, Medlar, Pear, Quince, Tejocote, including
cultivars, varieties and/or hybrids of these commodities.
Pests Controlled Product Rate
Aphids
 (including Wooly Apple Aphid)
Apple rust mite
Mealybugs
Pear psylla
Pear rust mite
San Jose scale
Whiteflies
(fl oz/A) (lb ai/A)
6.0 – 9.0 0.09 - 0.14

29
POME FRUITS (continued)
Pests Suppressed Product Rate
Apple gall midge
Codling moth
European red mite
Micro-lepidoptera leafminers
Pear leaf midge
Twospotted spider mite
White apple leafhopper
(fl oz/A) (lb ai/A)
6.0 – 9.0 0.09 - 0.14
Foliar Application Restrictions:
Pre-Harvest Interval (PHI): 7 day(s)
Minimum interval between applications: 14 days
Maximum MOVENTO allowed per  calendar year: 25 fl oz/A
Maximum spirotetramat per calendar year: 0.39 lb ai/A
Do not apply until after petal fall.
For control of San Jose scale west of the Rocky Mountains [including all of MT, WY,
CO, and NM], apply immediately after petal fall, followed by a second application
14 – 21 days later.  For control of San Jose scale east of the Rocky Mountains, apply
immediately after petal fall; under heavy infestation pressure or where difficult control
conditions exist, a second application may be necessary.

30
POMEGRANATE
Pests Controlled Product Rate
Aphids
Whiteflies
 (fl oz/A) (lb ai/A)
8.0 - 10.0 0.13 – 0.16
Foliar Application Restrictions:
Pre-Harvest Interval (PHI): 1 day(s)
Minimum interval between applications: 14 days
Maximum MOVENTO allowed per  calendar year: 20 fl oz/A
Maximum spirotetramat per calendar year: 0.31 lb ai/A

31
POTATO and OTHER TUBEROUS AND CORM VEGETABLES
Crops of Crop Subgroup 1C Including: Arracacha, Arrowroot, Artichoke (Chinese and
Jerusalem), Canna (edible), Cassava (bitter and sweet), Chayote (root), Chufa, Dasheen
(taro), Ginger, Leren,  Potato, Sweet potato, Tanier, Turmeric, Yam bean, Yam (true)
Pests Controlled Product Rate
Aphids
Psyllids
Whiteflies
(fl oz/A) (lb ai/A)
4.0 – 5.0 0.06 - 0.08
Pests Suppressed
Nematodes
Twospotted spider mite
Western flower thrips (larvae)
Wireworms
Foliar Application Restrictions:
Pre-Harvest Interval (PHI): 7 day(s)
Minimum interval between applications: 7 days
Maximum MOVENTO allowed per crop season: 10 fl oz/A
Maximum spirotetramat per crop season: 0.16 lb ai/A

32
SMALL FRUIT VINE CLIMBING SUBGROUP (Except Fuzzy Kiwifruit)
Crops of Crop Subgroup 13-07F Including: Amur river grape, Gooseberry, Grape,
Kiwifruit (hardy), Maypop, Schisandra berry
Pests Controlled Product Rate
Grape tumid gallmaker
Mealybugs
Phylloxera
Willamette mite
Whiteflies
 (fl oz/A) (lb ai/A)
6.0 – 8.0 0.10 - 0.13Pests Suppressed
European fruit lecanium scale
Pacific mite
Twospotted spider mite
Nematodes

Foliar Application Restrictions:
Pre-Harvest Interval (PHI): 7 day(s)
Minimum interval between applications: 30 days
Maximum MOVENTO allowed per calendar year:  12.5 fl oz/A
Maximum spirotetramat per calendar year: 0.2 lb ai/A
Some adjuvants that may be used with MOVENTO have caused intolerable damage
to grape berries / clusters when applied alone or in mixes after the initiation of bloom.
Testing has shown that MOVENTO does not increase the potential for damage when
used in combination with such adjuvants; however, not all adjuvants have been tested.
It is recommended that a high quality spreading-penetrating adjuvant be used at a rate
that is known to be safe to the crop.

33
STONE FRUITS
Crops of Crop Group 12-12 Including: Apricot; apricot, Japanese; capulin; cherry, black; cherry,
Nanking; cherry, sweet; cherry, tart; Jujube, Chinese; nectarine; peach; plum; plum, American;
plum, beach; plum, Canada; plum, cherry; plum, Chickasaw; plum, Damson; plum, Japanese;
plum, Klamath; plum, prune; plumcot; sloe; cultivars, varieties, and/or hybrids of these
Pests Controlled Product Rate
Aphids
Mealybugs
San Jose scale
White peach scale
Whiteflies
(fl oz/A) (lb ai/A)
6.0 – 9.0 0.09 - 0.14
Pests Suppressed
Black scale
Cherry fruit fly
European fruit lecanium scale
European red mite
Nematodes
Spotted Wing Drosophila
Twospotted spider mite
Foliar Application Restrictions:
Pre-Harvest Interval (PHI): 7 day(s)
Minimum interval between applications: 14 days
Maximum MOVENTO allowed per calendar year: 15.3 fl oz/A
Maximum spirotetramat per calendar year: 0.24 lb ai/A
Do not apply until after petal fall.
For control of San Jose scale, apply immediately after petal fall; under heavy infestation
pressure or where difficult control conditions exist, a second application may be necessary.

34
SUGAR BEET
Pests Controlled Product Rate
Bean aphid
Root Aphid
Whiteflies
(fl oz/A) (lb ai/A)
5.0 - 9.0 0.08 - 0.14Pests Suppressed
Root Maggot
Sugarbeet cyst nematode
Foliar Application Restrictions:
Pre-Harvest Interval (PHI): 28 day(s)
Minimum interval between applications: 14 days
Maximum MOVENTO allowed per crop season: 18 fl oz/A
Maximum spirotetramat per crop season: 0.28 lb ai/A

35
TREE NUTS
Crops of Crop Group 14-12 Including: African nut-tree; almond; beechnut; Brazil nut; Brazilian pine;
bunya; bur oak; butternut; Cajou nut; candlenut; cashew; chestnut; chinquapin; coconut; coquito nut;
dika nut; ginkgo; Guiana chestnut; hazelnut (filbert); heartnut; hickory nut; Japanese horse-chestnut;
macadamia nut; mongongo nut; monkey-pot; monkey puzzle nut; Okari nut; Pachira nut; peach palm
nut; pecan; pequi; Pili nut; pine nut; pistachio; Sapucaia nut; tropical almond; walnut, black; walnut,
English; yellowhorn; cultivars, varieties, and/or hybrids of these
Pests Controlled Product Rate
Aphids
Mealybugs
Phylloxera
San Jose scale
Walnut scale
Whiteflies
(fl oz/A) (lb ai/A)
6.0 – 9.0 0.09 - 0.14Pests Suppressed
European fruit lecanium scale
Nematodes
Olive scale
Pacific mite
Twospotted spider mite
Foliar Application Restrictions:
Pre-Harvest Interval (PHI): 7 day(s)
Minimum interval between applications: 14 days
Maximum MOVENTO allowed per calendar year: 21.5 fl oz/A
Maximum spirotetramat per calendar year: 0.34 lb ai/A
Do not apply until after petal fall.
For control of San Jose scale, apply immediately after petal fall; under heavy infestation
pressure or where difficult control conditions exist, a second application may be necessary.

36
TROPICAL FRUIT
Acerola, Avocado,  Black sapote, Canistel, Feijoa, Jaboticaba, Guava, Longan, Lychee,
Mamey sapote, Mango, Papaya, Passionfruit, Persimmon, Pulasan, Rambutan,
Sapodilla, Spanish lime, Star apple, Starfruit, Wax jambu, White sapote (Casimiroa spp.)
Pests Controlled Product Rate
Aphids
Avocado thrips
Mealybugs
Scales
Whiteflies
(fl oz/A) (lb ai/A)
8.0 – 10.0 0.13 - 0.16Pests Suppressed
Avocado brown mite
Papaya leaf edgeroller mite
Persea mite
Twospotted spider mite
Foliar Application Restrictions:
Pre-Harvest Interval (PHI): 1 day(s)
Minimum interval between applications: 14 days
Maximum MOVENTO allowed per calendar year: 25 fl oz/A
Maximum spirotetramat per calendar year: 0.39 lb ai/A

37
WATERCRESS
Pests Controlled Product Rate
Aphids  (fl oz/A) (lb ai/A)
4.0 - 12.5 0.06 – 0.2
Foliar Application Restrictions:
Pre-Harvest Interval (PHI): 3 day(s)
Minimum interval between applications: 7 days
Maximum MOVENTO allowed per crop season: 25 fl oz/A
Maximum spirotetramat per crop season: 0.39 lb ai/A
Do not plant or replant any crop not listed on this label within 260 days after the last application.

38
STORAGE AND DISPOSAL
Do not contaminate water, food or feed by storage or disposal.
Pesticide storage
MOVENTO is packaged in poly-ethylene containers. Do not allow product or containers to
freeze. Store in a cool, dry place and in such a manner as to prevent cross contamination with
other pesticides, fertilizers, food, and feed. Store in original container and out of the reach of
children, preferably in a locked storage area.
Handle and open container in a manner as to prevent spillage. If container is leaking,
invert to prevent leakage. If the container is leaking or material is spilled for any reason
or cause, carefully dam up spilled material to prevent runoff. Refer to Precautionary
Statements on label for hazards associated with the handling of this material. Do not walk
through spilled material. Absorb spilled material with absorbing type compounds and
dispose of as directed for pesticides below. In spill or leak incidents, keep unauthorized
people away. You may contact the Bayer CropScience Emergency Response Team for
decontamination procedures or any other assistance that may be necessary. The Bayer
CropScience Emergency Response Telephone No. is (800) 334-7577, or contact Chemtrec at
(800) 424-9300.
Pesticide disposal
Pesticide wastes are toxic. Improper disposal of excess pesticide, spray mixture, or rinsate
is a violation of Federal Law. If these wastes cannot be disposed of by use according to label
instructions, contact your State Pesticide or Environmental Control Agency, or the Hazardous
Waste representative at the nearest EPA Regional Office for guidance.
Container handling
Rigid, Non-refillable containers (equal to or less than 5 gallons)
Non-refillable container. Do not reuse or refill this container. Offer for recycling, if available.
Triple rinse or pressure rinse container (or equivalent) promptly after emptying. Triple rinse as
follows:  Empty the remaining contents into application equipment or a mix tank and drain for
10 seconds after the flow begins to drip. Fill the container 1/4 full with water and recap. Shake

39
for 10 seconds. Pour rinsate into application equipment or a mix tank or store rinsate for later
use or disposal. Drain for 10 seconds after the flow begins to drip. Repeat this procedure two
more times.
Pressure rinse as follows: Empty the remaining contents into application equipment or a mix
tank and continue to drain for 10 seconds after the flow begins to drip. Hold container upside
down over application equipment or mix tank or collect rinsate for later use or disposal. Insert
pressure rinsing nozzle in the side of the container, and rinse at about 40 PSI for at least 30
seconds. Drain for 10 seconds after the flow begins to drip.
Once container is rinsed, offer for recycling if available or puncture and dispose of in a sanitary landfill.
Bayer, Bayer Cross, and MOVENTO are registered trademarks of Bayer Group. ©2026 Bayer Group.
All rights reserved.
Induce is a registered trademark of Helena Holding Company

  NET CONTENTS: 1 GALLON
US61381471D       170628Dv3    07/26
US61381471D (170628Dv3) NAME 1 GALLON ETL BASE LABEL
COLORS: CMYK     DATE: 07/08/2026
Label Coordinator: Louis Cross
MOVENTO®
For Agricultural Use Only: For control of listed insects on certain tree, tropical
fruits, vine, and vegetable crops.
ACTIVE INGREDIENT: Spirotetramat: cis-3-(2,5-dimethylphenyl)-
 8-methoxy-2-oxo-1-azaspiro[4.5]dec-3-en-4-yl-ethyl carbonate ........ 22.40%
OTHER INGREDIENTS: ........................................... 77.60%
MOVENTO contains 2.00 pounds spirotetramat TOTAL: 100.00%
per US gallon (240 grams AI/liter)
EPA Reg. No. 264-1050
 KEEP OUT OF REACH OF CHILDREN
CAUTION
For MEDICAL And TRANSPORTATION Emergencies ONLY Call 24 Hours A Day 1-800-334-7577
For PRODUCT USE Information Call 1-866-99BAYER (1-866-992-2937)
Please refer to booklet for additional precautionary statements
and directions for use.
FIRST AID
If on skin or clothing: • Take off contaminated clothing. • Rinse skin immediately with plenty
of water for 15 to 20 minutes.  • Call a poison control center or doctor for treatment advice.
If swallowed: • Call a poison control center or doctor immediately for treatment advice.
• Have person sip a glass of water if able to swallow.  • Do not induce vomiting unless told
to do so by a poison control center or doctor. • Do not give anything by mouth to an
unconscious person. If in eyes: • Hold eye open and rinse slowly and gently with water for
15-20 minutes. • Remove contact lenses, if present, after the first five minutes, then continue
rinsing. • Call a poison control center or doctor immediately for treatment advice.
Have a product container or label with you when calling a poison control
center or doctor, or going for treatment. You may also contact 1-800-334-7577 for
emergency medical treatment information.
Note to Physician: No specific antidote is available. Treat the patient symptomatically.
PRECAUTIONARY STATEMENTS
HAZARDS TO HUMANS AND DOMESTIC ANIMALS
CAUTION
• Harmful if swallowed or absorbed through skin.
• Causes moderate eye irritation.
• Avoid contact with skin, eyes, or clothing.
• Wash thoroughly with soap and water after handling and before eating, drinking, chewing
gum, or using tobacco.
• Prolonged or frequently repeated skin contact may cause allergic reactions in
some individuals.
STORAGE AND DISPOSAL
Do not contaminate water, food or feed by storage or disposal.
Pesticide storage: MOVENTO is packaged in poly-ethylene containers.  Do not allow
product or containers to freeze. Store in a cool, dry place and in such a manner as to
prevent cross contamination with other pesticides, fertilizers, food, and feed.  Store in
original container and out of the reach of children, preferably in a locked storage area.
Handle and open container in a manner as to prevent spillage. If container is
leaking, invert to prevent leakage. If the container is leaking or material is spilled
for any reason or cause, carefully dam up spilled material to prevent runoff. Refer to
Precautionary Statements on label for hazards associated with the handling of this
material. Do not walk through spilled material. Absorb spilled material with absorbing
type compounds and dispose of as directed for pesticides below. In spill or leak
incidents, keep unauthorized people away. You may contact the Bayer CropScience
Emergency Response Team for decontamination procedures or any other assistance
that may be necessary. The Bayer CropScience Emergency Response Telephone No. is
(800) 334-7577, or contact Chemtrec at (800) 424-9300.
Pesticide disposal: Pesticide wastes are toxic. Improper disposal of excess pesticide,
spray mixture, or rinsate is a violation of Federal Law.  If these wastes cannot be
disposed of by use according to label instructions, contact your State Pesticide or
Environmental Control Agency, or the Hazardous Waste representative at the nearest
EPA Regional Office for guidance.
Container handling: Rigid, Non-refillable containers (equal to or less than 5 gallons)
Non-refillable container. Do not reuse or refill this container. Offer for recycling,
if available. Triple rinse or pressure rinse container (or equivalent) promptly after
emptying. Triple rinse as follows:  Empty the remaining contents into application
equipment or a mix tank and drain for 10 seconds after the flow begins to drip. Fill
the container 1/4 full with water and recap. Shake for 10 seconds. Pour rinsate into
application equipment or a mix tank or store rinsate for later use or disposal. Drain
for 10 seconds after the flow begins to drip. Repeat this procedure two more times.
Pressure rinse as follows: Empty the remaining contents into application equipment
or a mix tank and continue to drain for 10 seconds after the flow begins to drip. Hold
container upside down over application equipment or mix tank or collect rinsate for later
use or disposal. Insert pressure rinsing nozzle in the side of the container, and rinse at
about 40 PSI for at least 30 seconds. Drain for 10 seconds after the flow begins to drip.
Once container is rinsed, offer for recycling if available or puncture and dispose of in
a sanitary landfill.
Bayer and MOVENTO are registered trademarks of Bayer Group. ©2026 Bayer Group.
All rights reserved.
Produced For
Bayer CropScience LLC
800 N. Lindbergh Blvd.
St. Louis, MO 63167
GROUP 23 INSECTICIDEGROUP INSECTICIDE23