crop-chem-docs/corpus/epa_ppls/70506-60.md

# ULTRA BLAZER® HERBICIDE

- EPA Reg No: **70506-60**
- Registrant: UPL NA, INC.
- Signal word: Danger
- Active ingredients: Sodium acifluorfen (20.1%)
- Label accepted: 2023-07-27
- Source PDF: https://www3.epa.gov/pesticides/chem_search/ppls/070506-00060-20230727.pdf

---
UNITED STATES ENVIRONMENTAL PROTECTION AGENCY 
 WASHINGTON, DC 20460 
OFFICE OF CHEMICAL SAFETY 
AND POLLUTION PREVENTION 
New Use PRIA Unconditional v.20220527 
July 27, 2023 
 
Meshea J. Brodie 
Sr. Regional Regulatory Manager 
UPL NA, Inc. 
630 Freedom Business Center, Ste. 402 
King of Prussia, PA 19406 
 
Subject: PRIA Label Amendment – New use on vegetable soybean (edamame) and 
new use/crop group expansion from strawberry to low growing berries 
(crop subgroup 13-07G) 
 Supplemental Label – For Use on Edamame (vegetable soybean) 
 Registration Review Label Amendment – Incorporating Mitigation Measures 
from the Registration Review Interim Decision for Sodium Acifluorfen 
 Product Name: Ultra Blazer Herbicide 
 EPA Registration Number: 70506-60 
 Application Date: February 25, 2022 
 Decision Numbers: 582496, 592979 
 
Dear Meshea Brodie: 
 
The application referred to above, submitted under the Federal Insecticide, Fungicide, and 
Rodenticide Act (FIFRA), as amended, is acceptable under FIFRA section 3(c)(5). You must 
submit and/or cite all data required for registration/reregistration/registration review of your 
product when the Agency requires all registrants of similar products to submit such data. 
 
In addition, the Agency, in accordance with FIFRA, as amended, has completed reviewing all the 
information submitted with your application to support the Registration Review of the above 
referenced product in connection with the Sodium Acifluorfen Interim Decision. The Agency has 
concluded that your submission is acceptable. 
 
Stamped copies of the master and supplemental labels are enclosed for your records. This 
labeling supersedes all previously accepted labeling. You must submit one (1) copy of the final 
printed labeling before you release the product for shipment with the new labeling. In accordance 
with 40 CFR 152.130(c), you may distribute or sell this product under the previously approved 
labeling for 12 months from the date of this letter. After 12 months, you may only distribute or 
sell this product if it bears this new revised labeling or subsequently approved labeling. “To 
distribute or sell” is defined under FIFRA section 2(gg) and its implementing regulation at 40 
CFR 152.3. 
 
Should you wish to add/retain a reference to the company’s website on your label, then please be 
aware that the website becomes labeling under FIFRA and is subject to review by the Agency.

Page 2 of 2 
EPA Reg. No. 70506-60 
Decision Nos. 582496, 592979 
 
If the website is false or misleading, the product would be misbranded and unlawful to sell or 
distribute under FIFRA section 12(a)(1)(E). 40 CFR 156.10(a)(5) lists examples of statements 
EPA may consider false or misleading. In addition, regardless of whether a website is referenced 
on your product’s label, claims made on the website may not substantially differ from those 
claims approved through the registration process. Therefore, should the Agency find or if it is 
brought to our attention that a website contains false or misleading statements or claims 
substantially differing from the EPA approved registration, the website will be referred to the 
EPA’s Office of Enforcement and Compliance. 
 
Your release for shipment of the product constitutes acceptance of these conditions. If these 
conditions are not complied with, the registration will be subject to cancellation in accordance 
with FIFRA section 6. 
 
If you have any questions, please contact Derek Corbin at 202-566-2571 or at 
Corbin.Derek@epa.gov. 
 
 
Sincerely, 
 
 
 
 
 
 L i n d s a y R o e , C h i e f 
 H e r b i c i d e B r a n c h 
 Registration Division (7505T) 
 Office of Pesticide Programs 
 
 
 
Enclosures

Ultra Blazer label edamame Rev.2/25/22 Page 1 
 
 
 
 
 
ULTRA BLAZER® Herbicide 
For use on edamame (vegetable soybean, edible podded and succulent shelled), low growing 
berries (crop subgroup 13-07G), peanuts, rice, and soybeans 
 
ACTIVE INGREDIENT: Sodium salt of acifluorfen*……………………… ……………………2 0.1% 
OTHER INGREDIENTS:………………………………… ………………………… ……… ..…79.9 % 
TOTAL……………………………………………… …………………………………….....…100 .0% 
* Equivalent to 2 pounds of active ingredient per gallon. 
 
KEEP OUT OF REACH OF CHILDREN 
DANGER/PELIGRO 
Si usted no entiende la etiqueta, busque a alguien para que se la explique a usted en detalle. (If you do not 
understand the label, find someone to explain it to you in detail.) 
[SEE [BACK PANEL] [INSIDE BOOKLET] [BELOW] FOR ADDITIONAL 
PRECAUTIONARY STATEMENTS] 
 
FIRST AID 
IF IN EYES: • Hold eye open and rinse slowly and gently with water for 15-20 
minutes. 
• Remove contact lenses, if present, after the first 5 minutes, then 
continue rinsing eye. 
• Call a poison control center or doctor for treatment advice. 
IF ON SKIN OR 
CLOTHING: 
• Take off contaminated clothing. 
• Rinse skin immediately with plenty of water for 15 to 20 minutes. 
• Call a poison control center or doctor for treatment advice. 
IF SWALLOWED: • Call a poison control center or doctor immediately for treatment 
advice. 
• Have person sip a glass of water if able to swallow. Do not induce 
vomiting unless told to do so by the poison control center or doctor. 
• Do not give anything by mouth to an unconscious person. 
IF INHALED: • Move person to fresh air. 
• If person is not breathing, call 911 or an ambulance, then give 
artificial respiration, preferably by mouth-to-mouth, if possible. 
• Call a poison control center or doctor for further treatment advice. 
Hotline Number: Have the product container or label with you when calling a poison control center or 
doctor, or going for treatment. For emergency medical assistance, contact the Rocky Mountain Poison 
and Drug Safety at 1-866-673-6671. 
Note to Physician: Probable mucosal damage may contraindicate the use of gastric lavage. 
ANTIDOTE— No specific antidote is available. Treat symptomatically. 
 
FOR CHEMICAL EMERGENCY: Spill, leak, fire, exposure, or accident, call CHEMTREC at 1-800-424-9300 
 
UPL NA Inc. 
 630 Freedom Business Center EPA Reg. No. 70506-60 
 King of Prussia, PA 19406 EPA Est. No. 
 1-800-438-6071 Net Contents: 2.5 gallons, 250 gallons 
Sodium salt of acifluorfen GROUP 14 HERBICIDE 
Jul 27, 2023
70506-60

Ultra Blazer label edamame Rev.2/25/22 Page 2 
 
 
PRECAUTIONARY STATEMENTS 
HAZARDS TO HUMANS AND DOMESTIC ANIMALS 
DANGER 
Corrosive. Causes irreversible eye damage. Harmful if swallowed or absorbed through the skin, or 
inhaled. Do not get in eyes or on clothing. Avoid contact with skin and breathing spray mist. 
 
PERSONAL PROTECTION EQUIPMENT (PPE) 
Mixers, Loaders and Applicators must wear: 
• Long-sleeved shirt and long pants 
• Shoes plus socks 
• Chemical-resistant gloves, made of barrier laminate, butyl rubber >14 mils, nitrile rubber 
>14 mils, neoprene rubber >14 mils, natural rubber >14 mils, polyethylene, polyvinyl 
chloride (PVC) >14 mils, and Viton >14 mils 
• Protective eyewear (goggles or face shield) 
 
Discard clothing and other absorbent materials that have been drenched or heavily contaminated 
with this product’s concentrate. Do not re-use them. Follow manufacturer’s instructions for 
cleaning/maintaining PPE. If no such instructions for washables exist, use detergent and hot 
water. Keep and wash PPE separately from other laundry. 
 
Engineering Controls 
When handlers use closed systems, enclosed cabs, or cockpits in a manner that meets the 
requirements listed in the Worker Protection Standard (WPS) for agricultural pesticides (40 CFR 
170.607(d-f)), the handler PPE requirements may be reduced or modified as specified in the WPS. 
 
USER SAFETY RECOMMENDATIONS 
Users should: 
• Wash hands before eating, drinking, chewing gum, using tobacco or using the toilet. 
• Remove clothing/PPE immediately if pesticide gets inside. Then wash thoroughly and put 
on clean clothing. 
• Remove PPE immediately after handling this product. Wash the outside of gloves before 
removing. As soon as possible, wash thoroughly and change into clean clothing. 
 
ENVIRONMENTAL HAZARDS 
Do not apply directly to water, or to areas where surface water is present or to intertidal areas below 
the mean high water mark, except as specified on this label for application to rice. Do not 
contaminate water when disposing of equipment washwaters. Do not apply when weather conditions 
favor drift from target area. 
 
GROUND WATER ADVISORY 
Sodium acifluorfen is known to leach through soil to groundwater under certain conditions as a result 
of label use. Use of this chemical in areas where soils are permeable (sandy or sandy/loamy soils) 
and water tables are shallow could result in contamination of groundwater. Use of irrigated water in 
such areas will increase the likelihood of groundwater contamination. 
 
DIRECTIONS FOR USE 
It is a violation of Federal law to use this product in a manner inconsistent with its labeling. 
Do not apply this product in a way that will contact workers or other people, either directly or through 
drift. Only handlers wearing PPE may be in the treatment area during application. For any 
requirements specific to your State or Tribe, consult the State or Tribal agency responsible for 
pesticide regulation.

Ultra Blazer label edamame Rev.2/25/22 Page 3 
 
This pesticide is toxic to vascular plants and should be used strictly in accordance with the drift and 
run-off precautions on this label to minimize off-site exposures. All applicable directions, restrictions, 
precautions and Conditions of Sale and Warranty are to be followed. This labeling must be in the 
user’s possession during application. 
 
AGRICULTURAL USE REQUIREMENTS 
Use this product only in accordance with its labeling and with the Worker Protection Standard, 40 
CFR part 170. This Standard contains requirements for the protection of agricultural workers on 
farms, forests, nurseries, and greenhouses, and handlers of agricultural pesticides. It contains 
requirements for training, decontamination, notification, and emergency assistance. It also 
contains specific instructions and exceptions pertaining to the statements on this label about 
personal protective equipment (PPE) and restricted-entry interval. The requirements in this box 
only apply to uses of this product that are covered by the Worker Protection Standard. 
 
Do not enter or allow worker entry into treated areas during the restricted entry interval (REI) of 
48 hours. 
 
The following PPE is required for early entry into treated areas that is permitted under the 
Worker Protection Standard and that involves contact with anything that has been treated, such 
as plants, soil, or water 
• Coveralls over long sleeved shirt and long pants 
• Chemical-resistant gloves, made of barrier laminate, butyl rubber >14 mils, nitrile rubber 
>14 mils, neoprene rubber >14 mils, natural rubber >14 mils, polyethylene, polyvinyl 
chloride (PVC) >14 mils, and Viton >14 mils 
• Chemical resistant footwear plus socks 
• Chemical resistant headgear if overhead exposure 
• Protective eyewear 
Notify workers of pesticide application by warning them orally and by posting warning signs at 
entrances to treated areas. 
 
Fish Advisory Statement 
This product may be hazardous to aquatic organisms, particularly in clear, shallow water bodies that 
are adjacent to treated areas. Therefore, transport to water by runoff or spray drift of this product in 
areas where surface water is present, or intertidal areas below the mean high water mark should be 
avoided. Do not contaminate water when disposing of equipment wash water or rinsate. 
 
Pollinator Advisory Statement 
This product may adversely impact the forage and habitat of local pollinators, including the monarch 
butterfly (and its larvae), birds, or bats if it reaches non-target areas. Protect pollinators by following 
label directions to minimize spray drift. 
 
I. USE INFORMATION 
Ultra Blazer herbicide is a soluble liquid intended for selective postemergence control of certain 
broadleaf weeds and grasses in edamame (vegetable soybean), peanuts, soybeans, Strawberries 
and Low Growing Berries (crop subgroup 13-07G), and rice. 
 
Crop Rotation Restriction: In case of crop failure, only edamame (vegetable soybean), peanuts, 
soybeans, Strawberries and Low Growing Berries (crop subgroup 13-07G) or rice may be 
immediately replanted. Small grains must not be planted in fields treated with Ultra Blazer for 40 
days following treatment. All other rotated crops must not be planted in fields treated with Ultra 
Blazer for 100 days following treatment.

Ultra Blazer label edamame Rev.2/25/22 Page 4 
 
Crop Tolerance 
All listed crops are tolerant to Ultra Blazer at all stages of growth listed. Leaf speckling may occur, 
but plants generally outgrow this condition within 10 days. New growth is normal and crop vigor is 
not reduced. 
 
Cleaning Spray Equipment 
Clean application equipment thoroughly by using a strong detergent or commercial spray cleaner 
according to the manufacturer’s directions and then triple rinsing the equipment before and after 
applying this product. 
 
Herbicide Resistance Management 
For resistance management, Ultra Blazer is a Group 14 herbicide. Any weed population may contain 
or develop plants naturally resistant to Ultra Blazer and other Group 14 herbicides. Weed species 
with acquired resistance to Group 14 may eventually dominate the weed population if Group 14 
herbicides are used repeatedly in the same field. Appropriate resistance-management strategies 
should be followed. 
 
To delay herbicide resistance take one or more of the following steps: 
• Rotate the use of Ultra Blazer or other Group 14 herbicides within a growing season 
sequence or among growing seasons with different herbicide groups that control the same 
weeds in a field. Whenever possible incorporate multiple weed control practices such as 
mechanical cultivation, biological management practices, and crop rotation. 
• Use tank mixtures with herbicides from a different group if such use is permitted; where 
information on resistance in target weed species is available, use the less resistance-prone 
partner at a rate that will control the target weed(s) equally as well as the more resistance-
prone partner. Consult your local extension service or certified crop advisor if you are unsure 
as to which active ingredient is currently less prone to resistance. 
• Adopt an integrated weed-management program for herbicide use that includes scouting and 
uses historical information related to herbicide use and crop rotation, and that considers 
tillage (or other mechanical control methods), cultural (e.g. higher crop seeding rates; 
precision fertilizer application method and timing to favor the crop and not the weeds), 
biological (weed-competitive crops or varieties) and other management practices. 
• Fields should be scouted before application to identify the weed species present and their 
growth stage to determine if the intended application will be effective. Scout after herbicide 
application to monitor weed populations for early signs of resistance development. Indicators 
of possible herbicide resistance include: (1) failure to control a weed species normally 
controlled by the herbicide at the dose applied, especially if control is achieved on adjacent 
weeds; (2) a spreading patch of non-controlled plants of a particular weed species; (3) 
surviving plants mixed with controlled individuals of the same species. If resistance is 
suspected, prevent weed seed production in the affected area by an alternative herbicide 
from a different group or by a mechanical method such as hoeing or tillage. Prevent 
movement of resistant weed seeds to other fields by cleaning harvesting and tillage 
equipment when moving between fields, and planting clean seed. 
• If a weed pest population continues to progress after treatment with this product, discontinue 
use of this product and switch to another management strategy or herbicide with a different 
mode of action (MOA), if available. Treat weed escapes with an herbicide with a different 
MOA or use non-chemical methods to remove escapes. To the extent possible do not allow 
weed escapes to produce seeds, roots, or tubers. 
• Contact your local extension specialist, certified crop advisors, and/or manufacturer for 
additional herbicide resistance management and/or integrated weed management 
recommendations for specific crops and resistant weed biotypes. Report any incidence of 
non-performance of this product against a particular weed species to your retailer or UPL NA 
Inc. representative.

Ultra Blazer label edamame Rev.2/25/22 Page 5 
 
II. APPLICATION INSTRUCTIONS 
Apply labeled rates of Ultra Blazer as follows unless instructed differently in section VI. Crop-
Specific Information. Applications can be made to actively growing weeds as aerial banding or 
broadcast applications at the rates and growth stages listed in Table 4. Application Rates for Ultra 
Blazer herbicide – Peanuts and Soybeans and in VI. Crop-Specific Information for edamame 
(vegetable soybean), rice and Strawberries and Low Growing Berries (crop subgroup 13-07G). The 
most effective control will result from making postemergence applications of Ultra Blazer early, 
when weeds are small. Early application to weeds results in improved weed control, allows use of 
the lower rate (depending on weed species), and makes thorough spray coverage easier to obtain. 
Delaying application permits weeds to exceed the maximum size stated and will prevent adequate 
control. 
 
Irrigation 
In irrigated areas, it may be necessary to irrigate before treatment to ensure active weed growth. 
Weeds growing under drought conditions usually are not adequately controlled. 
 
Spray Coverage 
Weeds must be thoroughly covered with spray. Always use an adequate volume of spray solution to 
ensure thorough coverage. Dense leaf canopies shelter smaller weeds and can prevent adequate 
spray coverage. 
 
Cultivation 
Do not cultivate within 5 days before or 7 days after applying Ultra Blazer herbicide. 
 
Aerial Application Methods and Equipment 
Water Volume: Use a minimum of 10 gallons of water per acre. A minimum of 5 gallons of water per 
acre has been effective where adequate coverage can be achieved. 
Spray Pressure: Use up to 40 psi. 
 
Application Equipment: Use only diaphragm-type nozzles that produce cone or fan-spray spray 
patterns. 
 
Ground Application (Banding) 
Follow Ground Application (Broadcast) instructions for band applications. When row banding 
equipment is used, adjust it to provide maximum coverage of weeds in the row. Thorough coverage 
of the weeds can be obtained with two nozzles directed from either side of the crop row toward the 
weeds in the center rows. The minimum band width is 15 inches with a minimum of 15 gallons of 
water per acre on the band. Do not apply with a single nozzle over the row. 
 
Ground Application Methods and Equipment (Broadcast) 
Water Volume: Use 10-20 gallons of spray solution per broadcast acre for optimal performance. 
Increase water volume up to 50 gallons if crop or weed foliage is dense. For Strawberries and Low 
Growing Berries (crop subgroup 13-07G), use 20-40 gallons of spray solution per broadcast acre. 
 
Spray Pressure: Use a minimum of 40 psi (measured at the boom, not at the pump or in the line). 
Note: When using the lower water volume (i.e. 10 gallons per acre) or when crop and weed foliage 
is dense, use a minimum of 60 psi for best results. 
 
Application Equipment: Use standard high-pressure pesticide flat fan or hollow cone nozzles 
spaced up to 20 in. apart. Do not use flood, whirl chamber, or controlled droplet applicator (CDA) 
nozzles as erratic coverage can cause inconsistent weed control. Do not use selective application 
equipment such as recirculating sprayers or wiper applicators.

Ultra Blazer label edamame Rev.2/25/22 Page 6 
 
SPRAY DRIFT 
Ground boom applications: 
• When using ground application equipment, apply with nozzle height no more than 4 feet a bove the ground 
or crop canopy. 
• Applicators are required to use a medium or coarser droplet size (ASABE S572.3). 
• Do not apply when wind speeds exceed 10 miles per hour at the application site. 
• Do not apply during temperature inversions. 
 
Aerial applications: 
• When applying aerially to crops, do not release spray at a height greater than 10 ft. above the crop canopy, 
unless a greater application height is necessary for pilot safety. 
• Applicators are required to use a medium or coarser spray droplet size (ASABE S572.3). 
• When applying to crops via aerial application equipment, the spray boom must be mounted on the aircraft 
so as to minimize drift caused by wing tip or rotor blade vortices. The boom length must not exceed 75% of 
the wingspan or 90% of the rotor blade diameter. 
• When applying to crops via aerial application equipment, applicators must use ½ swath displacement 
upwind at the downwind edge of the field. 
• Nozzles must be oriented so the spray is directed toward the back of the aircraft. 
• Do not apply when wind speeds exceed 10 miles per hour at the application site. 
• Do not apply during temperature inversions. 
 
SPRAY DRIFT ADVISORIES 
THE APPLICATOR IS RESPONSIBLE FOR AVOIDING OFF-SITE SPRAY DRIFT. 
BE AWARE OF NEARBY NON-TARGET SITES AND ENVIRONMENTAL CONDITIONS. 
IMPORTANCE OF DROPLET SIZE 
An effective way to reduce spray drift is to apply large droplets. Use the largest droplets that provide target pest 
control. While applying larger droplets will reduce spray drift, the potential for drift will be greater if app lications 
are made improperly or under unfavorable environmental conditions. 
Controlling Droplet Size – Ground Boom 
• Volume - Increasing the spray volume so that larger droplets are produced will reduce spray drift. Use the 
highest practical spray volume for the applicat ion. If a greater spray vo lume is needed, consider using a 
nozzle with a higher flow rate. 
• Pressure - Use the lowest spray pressure recommended for the nozzle to produce the target spray volume 
and droplet size. 
• Spray Nozzle - Use a spray nozzle that is designed for the intended application. Consider using nozzles 
designed to reduce drift. 
Controlling Droplet Size – Aircraft 
• Adjust Nozzles - Follow nozzle manufacturers recommendations for setting up nozzles. Generally, to 
reduce fine droplets, nozzles should be oriented parallel with the airflow in flight. 
BOOM HEIGHT – Ground Boom 
For ground equipment, the boom should remain level with the crop and have minimal bounce. 
RELEASE HEIGHT - Aircraft 
Higher release heights increase the potential for spray drift. 
SHIELDED SPRAYERS 
Shielding the boom or individual nozzles can reduce spray drift. Consider using shielded sprayers. Verify that 
the shields are not interfering with the uniform deposition of the spray on the target area. 
TEMPERATURE AND HUMIDITY 
When making applications in hot and dry conditions, use larger droplets to reduce effects of evaporation. 
TEMPERATURE INVERSIONS 
Drift potential is high during a temperature inversion. Temperature inversions are characterized by inc reasing 
temperature with al titude and are common on ni ghts with limited cloud cover and light to no wind. The 
presence of an inversion can be indicated by ground fog or by the movement of smoke from a ground source 
or an aircraft smoke generator. Smoke that layers and moves laterall y in a concentrated cloud (under low wind 
conditions) indicates an inversion, while smoke that moves upward and rapidly dissipates indicates good

Ultra Blazer label edamame Rev.2/25/22 Page 7 
 
vertical air mixing. Avoid applications during temperature inversions. 
WIND 
Drift potential generally increas es with wind speed. AVOID APPLICATIONS DURING GUSTY WIND 
CONDITIONS. 
Applicators need to be familiar with local wind patterns and terrain that could affect spray drift. 
 
TEMPERATURE AND HUMIDITY 
When making applications in hot and dry conditions, set up equipment to produce larger droplets to reduce 
effects of evaporation. 
 
TEMPERATURE INVERSIONS 
Drift potential is high during a temperature inversion. Temperature inversions restrict vertical air mixing, which 
causes small suspended droplets to remain close to the ground and move laterally in a concentrated cloud. 
Temperature inversions are characterized by increasing temperature with altitude and are common on nights 
with limited cloud cover and light to no wind. They begin to form as the sun sets and often continue i nto the 
morning. Their presence can be indicated by ground fog; however, if fog is not present, inversions can also be 
identified by the movement of smoke from a ground source or an aircraft smoke generator. Smoke that layers 
and moves laterally in a concentrated cloud (under low wind conditions) indicates an inversion, while smoke 
that moves upward and rapidly dissipates indicates good vertical air mixing. 
 
SHIELDED SPRAYERS 
Shielding the boom or individual nozzles can reduce the effects of wind. However , it is the responsibility of the 
applicator to verify that the shields are preventing drift and not interfering with uniform depos ition of the 
product. 
 
 
III. MIXING INFORMATION 
 
Mixing Order 
1. Water. Begin by agitating a thoroughly clean sprayer tank three-quarters full of clean water. 
2. Agitation. Maintain constant agitation throughout mixing and application. 
3. Products in PVA Bags. Place any product contained in water-soluble PVA bags into the 
mixing tank. Wait until all water-soluble PVA bags have fully dissolved and the product is 
evenly mixed in the spray tank before continuing. 
4. Water dispersible products (such as dry flowables, wettable powders, suspension 
concentrates, or suspo-emulsions). If an inductor is used, rinse it thoroughly after the 
component has been added. 
5. Water-soluble products (such as Ultra Blazer). If an inductor is used, rinse it thoroughly 
after the component has been added. 
6. Emulsifiable concentrates (such as oil concentrate when applicable). If an inductor is used, 
rinse it thoroughly after the component has been added. 
7. Water-soluble additives (such as AMS or UAN when applicable). If an inductor is used, 
rinse it thoroughly after the component has been added. 
8. Remaining quantity of water. Maintain constant agitation during application. 
 
Compatibility Test for Mix Components 
Before mixing components, always perform a compatibility jar test. For 20 gallons per acre spray 
volume, use 3.3 cups (800 ml) of water. For other spray volumes, adjust rates accordingly. Only use 
water from the intended source at the source temperature. 
 
Add components in the sequence indicated in Mixing Order using 2 teaspoons for each pound or 1 
teaspoon for each pint of label rate per acre. Always cap the jar and invert 10 cycles between 
component additions. 
 
When the components have all been added to the jar, let the solution stand for 15 minutes. Evaluate 
the solution for uniformity and stability. The spray solution should not have free oil on the surface,

Ultra Blazer label edamame Rev.2/25/22 Page 8 
 
nor fine particles that precipitate to the bottom, nor thick (clabbered) texture. If the spray solution is 
not compatible, repeat the compatibility test with the addition of a suitable compatibility agent. If the 
solution is compatible, use the compatibility agent as directed on its label. If the solution is still 
incompatible, do not mix the ingredients in the same tank. 
 
See section VI. Crop-Specific Information for more details. Read and follow the applicable 
Restrictions and Limitations and Directions for Use on all products involved in tank mixing. The 
most restrictive labeling applies to tank mixes. Physical incompatibility, reduced weed control, or 
crop injury may result from mixing Ultra Blazer with other pesticides (fungicides, herbicides, 
insecticides, or miticides), additives, or fertilizers. The user assumes all risks of using tank mixes 
other than those listed. 
 
It is the pesticide user’s responsibility to ensure that all products are registered for the intended use. 
Read and follow the applicable restrictions, limitations, and directions for use on all product labels 
involved in the tank mixture. Users must follow the most restrictive directions for use and 
precautionary statements of each product in the tank mixture. 
 
IV. ADDITIVES 
 
To achieve consistent weed control, use one of the following additives with Ultra Blazer: ammonium 
sulfate, crop oil concentrate, nonionic surfactant, or urea ammonium nitrate. Use AMS (or UAN) 
when velvetleaf is a target weed. Additives may cause some leaf burn, but new growth is normal and 
crop vigor is not reduced. The potential for leaf burn is increased when relative humidity and 
temperature are high. Consult your local UPL NA Inc. representative for your area. See Table 2 
Additive Rates Per Acre for additive rates and Table 1 Additive Options for Ultra Blazer 
herbicide Tank Mixes. 
 
Ammonium Sulfate (AMS) 
AMS is a dry, granular nitrogen-source fertilizer. Use only fine feed-grade or spray-grade AMS 
because inferior grades of AMS do not dissolve adequately and can plug spray nozzles. Do not 
apply AMS if applied in less than 10 gallons per acre because of potential problems with precipitation 
in reduced volumes. Use AMS only if it has been demonstrated to be successful in local experience. 
 
Nonionic Surfactant 
The standard label rate is 1-2 pints of an 80% active nonionic spray surfactant per 100 gallons of 
water. For certain weeds, use the higher spray surfactant rate. 
 
Oil Concentrate 
The oil concentrate must contain either a petroleum or vegetable oil base and must meet all of the 
following criteria: 
• be nonphytotoxic, 
• contain only EPA-exempt ingredients, 
• provide good mixing quality in the compatibility test, and 
• be successful in local experience. 
 
The exact composition of suitable products will vary; however, vegetable and petroleum oil 
concentrates should contain emulsifiers to provide good mixing quality. Highly refined vegetable oils 
have proven more satisfactory than unrefined vegetable oils. For additional information, see 
Compatibility Test for Mix Components. 
Some oil concentrates cause excessive leaf burn. Refer to your supplier for information concerning 
successful local experience before purchasing any oil concentrate.

Ultra Blazer label edamame Rev.2/25/22 Page 9 
 
Urea Ammonium Nitrate (UAN) 
Commonly referred to as 28%, 30%, or 32% nitrogen solution, UAN may be added in place of other 
spray additives to improve weed control. Because most nitrogen solutions are mildly corrosive to 
galvanized, mild steel, and brass spray equipment, rinse the entire spray system with water soon 
after. Do not use brass or aluminum nozzles when spraying UAN. 
 
Temperature and Relative Humidity Effects 
The following standard will help determine the optimum adjuvant rate to use. If the temperature and 
relative humidity exceed 150 (e.g. temperature of 85ºF plus 70% relative humidity = 155), use the 
lower adjuvant rates. 
 
Table 1 – Additive Options for Ultra Blazer Tank Mixes 
 
 
 
Additive 
Options 
 
Nonionic 
Surfactant 
(1-2 pints 
per 100 
gallons) 
 
AMS 
(2.5 
pounds) 
or UAN 
(4-8 pints 
per acre) 
 
Crop Oil 
Concentrate 
(1-2 pints 
per acre) 
Nonionic 
Surfactant 
(1-2 pints per 100 
gallons) 
+ 
AMS (1-2 pounds 
per acre) or UAN 
(2-4 pints per 
acre) 
Crop Oil 
Concentrate 
(1 pint per acre) 
+ 
AMS (1-2 
pounds per 
acre) or UAN (2-
4 pints per acre) 
Option A ● 
Option B ● 
Option 
C 
 ● 
Option 
D 
 ● 
Option E ● 
 
Table 2 – Additive Rate Per Acre 
Additive Ground Application Air Application 
(Not for use on 
strawberries, low 
growing berries and 
edamame) 
Nonionic 
Surfactant 
1-2 pints per 100 gallons 1-2 pints per 100 gallons 
AMS 
Oil Concentrate 
UAN Solution 
2.5 pounds 
1-2 pints 
4-8 pints 
2.5 pounds 
1-2 pints 
4 pints 
 
 
V. LIMITATIONS AND RESTRICTIONS – ALL CROPS 
• Stress: Unsatisfactory control may result if applied to weeds or crops under stress due to 
lack of moisture, hail damage, flooding, herbicide injury, mechanical injury, or widely 
fluctuating temperatures. 
• Do not apply Ultra Blazer to crops that show injury (leaf phytotoxicity or plant stunting) 
produced by any other prior herbicide applications, because this injury may be enhanced or 
prolonged. 
• Rainfast Period: Rainfall or overhead irrigation within 4 hours after application may reduce 
the effectiveness of Ultra Blazer. 
• Do not apply through any type of irrigation system.

Ultra Blazer label edamame Rev.2/25/22 Page 10 
 
Table 3 – Crop-Specific Restrictions and Limitations 
Crop Minimum 
Time from 
Application 
to Harvest 
(PHI) 
Maximum 
Rate Per 
Acre Per 
Application 
Maximum 
Rate Per 
Acre Per 
Season 
Maximum 
Rate of 
A.I/Acre 
per 
Season 
Livestock 
Grazing or 
Feeding 
Aircraft 
Application 
 
Edamame 
(vegetable 
soybean) 
35 days 1.0 pint 1.0 pint 0.25 lbs No No 
Peanuts 75 days 1.5 pints 2.0 pints 0.50 lbs No Yes 
Rice 50 days 1.0 pint 1.0 pint 0.25 lbs No Yes 
Soybeans 50 days 1.5 pints 2.0 pints 0.50 lbs No Yes 
Strawberries 
and Low 
Growing 
Berries 
(crop 
subgroup 
13-07G) 
60 days 1.5 pints 3.0 pints 0.75 lbs No No 
 
 
VI. SPECIFIC CROP INFORMATION 
 
EDAMAME (VEGETABLE SOYBEAN) edible podded or succulent shelled 
Apply by ground only. Apply 1.0 pint of Ultra Blazer herbicide (0.25 lb ai)/A in sufficient water for 
uniform coverage (minimum of 10 gal/A) to control broadleaf weeds including glyphosate-tolerant 
amaranth, up to the R2 stage of growth. An adjuvant can be applied at a rate recommended by the 
adjuvant label. 
 
Restrictions 
• Do not make more than one application of Ultra Blazer herbicide per year. 
• Do not apply more than 1.0 pint (0.25 lbs ai)/A in a single application. 
• Do not make more than 1.0 pint (0.25 lbs ai)/A per year. 
• Do not apply later than the R2 stage of growth. 
• Do not use treated plants for feed or forage. 
• Do not apply within 35 days before harvest. 
• Do not apply by air. 
• Do not apply by handheld application equipment. 
 
 
PEANUTS 
Apply the rates of Ultra Blazer herbicide listed in Table 4 to peanuts pre-emergence, at cracking 
stage (initiation of soil cracking, but before peanut emergence from the soil), or postemergence to 
peanuts to control susceptible weeds. Apply by ground or air. 
 
Peanut Tank Mixes 
Ultra Blazer may be applied in a tank mix with one of the following herbicides. Always follow the 
most restrictive directions of products used in tank mixtures. 
 
Tank Mix Partner Additive Option 
Sodium salt of bentazon A or C 
Ammonium salt of imazapic A 
S- Metolachlor A 
Sethoxydim C

Ultra Blazer label edamame Rev.2/25/22 Page 11 
 
2,4-DB* A or C 
 
* Do not apply this tank mix after pod-filling stage begins. Refer to Table 1 for the additive option 
appropriate to each tank mix. 
 
 
Restrictions 
• Allow a minimum of 15 days between sequential applications of Ultra Blazer. 
• Do not apply more than 1.5 pints Ultra Blazer per acre per application, and do not apply more 
than 2 pints (0.50 lbs ai)/A Ultra Blazer per season. 
• Do not make more than 2.0 pints (0.50 lbs ai)/A per year. 
• Do not apply within 75 days before harvest. 
• Do not use treated plants for feed or forage. 
 
RICE 
Ultra Blazer may be applied when rice is at the late tillering stage up to the early boot stage, which 
normally occurs in June or July. Rice must be past the 3-leaf stage. Apply Ultra Blazer to hemp 
sesbania plants before sesbania is in the flowering stage. Best results are obtained when the 
sesbania growth extends above the rice. 
Apply 0.5 pint of Ultra Blazer per acre to hemp sesbania plants. A second application of 0.5 pint of 
Ultra Blazer per acre can be made to control later germinating sesbania. To achieve consistent 
weed control, add 1-2 pints of an 80% active nonionic spray surfactant per 100 gallons of water. 
Using a spray adjuvant is important for effective control of hemp sesbania. Apply by ground or air. 
 
Rice Tank Mixes 
Ultra Blazer may be applied in a tank mix with one of the following herbicides. Always follow the most 
restrictive directions of products used in tank mixtures. 
 
 Tank Mix Partner Additive Option 
 Sodium salt of bentazon A 
 Quinclorac A 
 Propanil A 
 
Refer to Table 1 for the additive option appropriate for each tank mix. 
 
Restrictions 
• Allow a minimum of 15 days between sequential applications of Ultra Blazer. 
• Do not apply Ultra Blazer after the rice reaches the boot stage. 
• Do not apply more than 1 pint (0.25 lbs ai)/A Ultra Blazer per acre per application, and do not 
make more than two applications of Ultra Blazer per season. 
• Do not make more than 2.0 pint (0.50 lbs ai)/A per year 
• Do not apply within 50 days before harvest. 
• Do not use water from treated rice fields for irrigation purposes for crops other than those 
labeled for use with Ultra Blazer herbicide. 
• Do not harvest crayfish from treated rice areas for food. 
• Do not use treated plants for feed or forage.

Ultra Blazer label edamame Rev.2/25/22 Page 12 
 
SOYBEANS 
To ensure optimum spray coverage of weeds, apply Ultra Blazer herbicide to small actively growing 
weeds. Refer to section II Application Instructions and Table 4 for more information. A sequential 
application of 1 pint of Ultra Blazer following 1 pint of Ultra Blazer can be used to control 
subsequent weed flushes or escaped weeds before they reach the maximum weed size listed in 
Table 4. Apply by ground or air. 
 
Soybean Tank Mixes 
Ultra Blazer may be applied in a tank mix with one of the following herbicides. Always follow the 
most restrictive directions of products used in tank mixtures. 
 
Tank Mix Partner Additive Option 
Quizalofop-P-Ethyl1 A 
Sodium salt of bentazon A or C 
Chlorimuron Ethyl A 
Chlorothalonil D 
Cloransulam-methyl D 
Fluazifop-P-butyl1 A 
Glyphosate 8.5-17 pounds 
of AMS per 
100 gallons 
Metolachlor1 A 
Thifensulfuron methyl A or D 
Sethoxydim1 C 
Sethoxydim1 C 
Sethoxydim1 C 
Ammonium salt of imazethapyr D 
Ammonium salt of imazamox D 
Flumiclorac pentyl ester C 
Imazaquin A 
Clethodim C 
2,4-DB A 
 
1 For best results if applying as part of a weed control program with Ultra Blazer, follow these 
guidelines: 
• If the partner is applied prior to the Ultra Blazer application, wait 24 hours before applying 
Ultra Blazer. 
• If the partner is applied following the Ultra Blazer application, wait 7 days before applying. 
 
Refer to Table 1 for the additive option appropriate for each tank mix. 
 
Burndown Treatment Before Planting Soybeans 
Ultra Blazer alone can be applied any time before planting soybeans to control susceptible weed 
species present (See Table 4). This application is not intended to replace a full-season weed control 
program, but is intended to control susceptible weed species present before soybeans are planted. 
Use a spray additive to enhance burndown activity before planting soybeans. 
 
Burndown Tank Mixes 
Ultra Blazer may be applied in a tank mix with one of the following herbicides. Always follow the most 
restrictive directions of products used in tank mixtures. 
 
Tank Mix Partner Additive Option 
 Sethoxydim C or E

Ultra Blazer label edamame Rev.2/25/22 Page 13 
 
 2,4-D LVE C 
 
 
Refer to Table 1 for the additive option appropriate for each tank mix. 
 
Restrictions 
• Allow a minimum of 15 days between sequential applications of Ultra Blazer. 
• Do not apply more than 1.5 pints Ultra Blazer per acre per application, and do not apply more 
than 2 pints (0.50 lbs ai)/A Ultra Blazer per season. 
• Do not make more than 2.0 pints (0.50 lbs ai)/A per year. 
• Do not apply within 50 days before harvest. 
• Do not use treated plants for feed or forage. 
 
Glyphosate Tolerant Soybean Tank Mixtures 
Postemergent applications of Ultra Blazer
® herbicide can be applied in a tank mixture with 
glyphosate containing herbicides for control of glyphosate resistant weeds. Targeted weeds must be 
listed on the Ultra Blazer label and are susceptible to Ultra Blazer. Refer to the Ultra Blazer label for 
weeds controlled, application rates and application timing. Follow the directions on the glyphosate 
product label for the use of spray additives in this tank mixture. It is important to follow the Ultra 
Blazer instructions for weed growth stages and application rates for effective broadleaf weed control. 
Apply Ultra Blazer and glyphosate containing herbicides only to glyphosate tolerant soybeans or 
severe crop injury or plant death will occur. 
 
STRAWBERRIES AND LOW GROWING BERRIES (crop subgroup 13-07G) 
Bearberry; bilberry; blueberry, lowbush; cloudberry; cranberry; lingonberry; muntries; partridgeberry; 
strawberry; cultivars, varieties, and/or hybrids of these 
(one season per 12 month period) 
 
For control of many broadleaf weeds, Ultra Blazer may be applied up to the maximum application 
rate of 0.375 lb a.i. per acre (1.5 pints Ultra Blazer per acre per season) using ground equipment. 
Make broadcast applications of the mixture in 20 to 40 gallons of water per acre. Reduce rates 
proportionately for band or strip treatment. Do not apply more than 0.75 lb a.i. per acre per season (3 
pints Ultra Blazer per acre per season). Apply by ground only. 
 
For Annual Strawberries grown on plastic mulch on plant beds: 
 
Make one banded application before laying plastic mulch and after final land preparation, and prior to 
transplanting the crop. For best results, avoid soil disturbance during laying of plastic and planting of 
crop. 
 
For application between rows of plastic mulch, apply as a direct-shielded application to strawberry 
row middles between mulched beds. Do not allow Ultra Blazer to contact strawberry plants. 
 
For Perennial Strawberries: Make two applications. The first application can be made after the last 
harvest, or following bed renovation. The second application can be made when the plants are 
dormant during late fall to early spring. Do not apply the last application within 120 days of 
strawberry harvest. For application to row middles, Ultra Blazer may be applied up to the maximum 
rate of 0.375 lb a.i. per acre per season (1.5 pints Ultra Blazer per acre per season). 
 
Restrictions 
• Allow a minimum of 15 days between sequential applications of Ultra Blazer. 
• Do not apply more than 1.5 pints Ultra Blazer per acre per application, and do not apply more 
than 3 pints (0.75 lbs ai)/A Ultra Blazer per season. 
• Do not make more than 3.0 pints (0.75 lbs ai)/A per year.

Ultra Blazer label edamame Rev.2/25/22 Page 14 
 
• Do not apply within 60 days before harvest. 
• Do not use treated plants for feed or forage. 
• Do not apply by air. 
 
Table 4. Application Rates for Ultra Blazer Herbicide – Peanuts and Soybeans 
Refer to section VI. Crop-Specific Information for rate and timing details for edamame, strawberry 
(and other low growing berries) and for rice. Note: Weed height will vary depending on 
environmental conditions and is only given as a guide – leaf stages are more important than height in 
determining rate to use. Refer to section III. Additives for more information. 
Weeds Controlled 
(including glyphosate, 
triazine and ALS-
resistant biotypes) 
Scientific Name 
0.5 pint per acre 1.0 pint per acre 1.5 pints per acre 
Leaf 
Stagea 
(up to) 
Maximum 
Height 
Leaf 
Stag
ea 
(up 
to) 
Maximum 
Height 
Leaf 
Stage
a (up 
to) 
Maximum 
Height 
Amaranth, Palmer Amaranthus 
palmeri 
4 <2” 6 <4” 6 4” 
 , Spiny Amaranthus 
spinosus 
- - 2 <2” 2 2” 
Balloonvine Cardiospemum 
halicacaburm 
- - - - 2 2” 
Beggarweed, Floridab,e Desmodium 
tortuosum 
- - - - 2 1-1/2" 
Buckwheat, Wildc,e Polygonum 
convolvulus 
- - - - 2 2” 
Buffaloburc,e Solanum 
rostratum 
- - - - 2 2” 
Burgherkind,e Cucumis 
anguria 
- - - - 2 2” 
Carpetweed Mollugo 
verticillata 
- - Multi 
3” 
dia. 
<2” Multi 
6” dia. 
2” 
Citron (Wild 
Watermelon)d,e 
Citrullus lanatus - - - - 2 2” 
Cocklebur e Xanthium 
strumarium 
- - - - 2 2” 
Copperleaf, Hophorn 
beam 
Acalypha 
ostryifolia 
- - 2 2” 4 4” 
 ,Virginia Acalypha 
virginica 
- - - - 2 2” 
Crotolaria, Showy f,e Crotalaria 
spectabillis 
- - 6 6” 6 6” 
Croton, Tropic Croton 
glandulosus var. 
septentrionalis 
- - 1-2 <2” 2 2” 
 ,Wooly Croton capitatus - - 1-2 <2” 2 2”

Ultra Blazer label edamame Rev.2/25/22 Page 15 
 
 
Crownbeard, Golden Verbesina 
encelioides 
- - - - 2 <2” 
Eclipta Eclipta alba - - - - 6 <2” 
Galinsoga, Hairy Galinsoga 
quadriradiata 
- - - - 4 <2” 
 , Smallflower Galinsoga 
parviflora 
- - - - 4 <2” 
Groundcherry, Cutleaf Physalis 
angulata 
- - - - 2 1” 
 , Lanceleaf Physalis 
lanceifolia 
- - - - 2 1” 
Indigo, Hairy Indigofera 
hirsuta 
- - - - 3 <2” 
Jimsonweed Datura 
stramonium 
- - 4 4” 6 6” 
Ladysthumb Polygonum 
persicaria 
- - 4 4” 6 6” 
Lambsquarters, Common 
g 
Chenopodium 
album 
- - - - 2 2” 
Morningglory, 
Cypressvineh 
Ipomoea 
quamoclit 
- - 2 2” 4 4” 
 , Ivyleafh Ipomoea 
hederacea 
- - 2 2” 4 4” 
 , Palmleaf h 
 (Willowleaf)h 
 Ipomoea 
wrightii 
 2 2" 4 4" 
 , 
PurpleMoonflowerh 
Ipomoea 
turbinata 
- - 2 2” 4 4” 
 , Red Ipomoea 
coccinea 
- - 2 2” 4 4” 
 , Smallflowerh Jacquemontia 
tamnifolia 
- - 2 2” 4 4” 
 ,Small White 
(pitted) h 
Ipomoea 
lacunosa 
-- - 2 2” 4 4” 
 , Tall (common) h Ipomoea 
purpurea 
- - 2 2” 4 4” 
Mustard, Wild Sinapis arvensis 2 2” 4 <4” 4 4” 
Nightshade, Eastern 
Black 
Solanum 
ptycanthum 
- - 2-3 <2” 6 2” 
 , Black Solanum nigrum - - 2-3 <2” 6 2” 
Pigweed, Palmer Amaranthus 
palmeri 
4 <2” 6 <4” 6 4” 
 , Prostrate Amaranthus 
blitoides 
- - - - 4 4” 
 , Redroot Amaranthus 
retroflexus 
4 <2” 6 <4” 6 4” 
 , Smooth Amaranthus 
hybridus 
4 <2” 6 <4” 6 4” 
 , Spiny Amaranthus 
spinosus 
- - 2 <2” 2 2” 
Poinsettia, Wild 'i,e Euphorbia 
heterophylla 
- - - - 2 2” 
Poorjoe Diodia teres - - - - 2 2” 
Purslane, Common Portulaca 
oleracea 
- - - - Multi 
6” dia 
1”

Ultra Blazer label edamame Rev.2/25/22 Page 16 
 
 
Pusley, Florida Richardia 
scabra 
- - 2 2” 4 4” 
Ragweed, Common Ambrosia 
artemisiifolia 
- - 2 2” 4 3” 
 , Giant Ambrosia trifida - - 2 <2” 2 3” 
Senna, Coffeej Senna 
occidentalis 
- - - - 2 2” 
Sesbania, Hemp f,e Sesbania 
herbacea 
- - 4 4”b 6 6” 
Smartweed, Pennsylvania Polygonum 
pensylvanicum 
- - 4 4” 6 6” 
Smellmelond,e Cucumis melo - - - - 2 2”b 
Spurge, Prostrate Chamaesyce 
maculate 
- - - - Multi 
0.5” 
dia 
- 
 , Spotted Chamaesyce 
maculate 
- - - - Multi 
0.5” 
dia 
- 
Starbur, Bristlyj Acanthospermu
m hispidum 
- - - - 2 2” 
Velvetleafk Abutilon 
theophrasti 
- - - - 4 2” 
Waterhemp, Common Amaranthus 
rudis 
4 2” 6 <4” 6 4” 
 ,Tall Amaranthus 
tuberculatus 
4 2” 6 <4” 6 4” 
Annual Grassesl Scientific Name 
0.5 pint per acre 1.0 pint per acre 1.5 pints per acre 
Leaf 
Stagea 
(up to) 
Maximum 
Height 
Leaf 
Stage
a (up 
to) 
Maximu
m Height 
Leaf 
Stage
a (up 
to) 
Maximum 
Height 
Foxtail, Giant l Setaria faberi - - - - 2 1” 
 , Green l Setaria viridis 
 ,Yellow l Setaria pumilia 
Johnsongrass, Seedling l Sorghum 
halepense 
Panicum, Fall l Panicum 
dichotomiflorum 
Shattercane l Sorghum bicolor 
Volunteer Small Grains l 
 Barley l Hordeum 
vulgare 
 Corn l Zea mays 
 Oats l Avena sativa 
 Rye l Secale cereal 
 Wheat l Triticum 
aestivum

Ultra Blazer label edamame Rev.2/25/22 Page 17 
 
 
Perennial Weeds 
Suppressed g,m 
(including triazine and 
ALS-resistant biotypes) 
Scientific 
Name 
0.5 pint per acre 1.0 pint per acre 1.5 pints per acre 
Leaf 
Stagea 
(up to) 
Maximum 
Height 
Leaf 
Stagea 
(up to) 
Maximum 
Height 
Leaf 
Stagea 
(up to) 
Maximum 
Height 
Bindweed, Field g, m Convolvulus 
arvensis 
- - - - 
See Footnotes 
g and m 
 Hedge g,m Calystegia 
sepium 
Milkweed, Climbing g, m Funastrum 
cynanchoides 
 Common g, m Asclepias 
syriaca 
Redvine, Trumpetcreeper 
g,m 
Brunnichia 
ovata 
a Do not count leaves as pairs; count each leaf separately. Do not count cotyledon leaves. Do not spray 
weeds in the cotyledon growth stage. 
b Controlling Florida beggarweed is difficult because of the weed’s long germination season. Apply Ultra 
Blazer herbicide when beggarweed seedlings have no more than 2 young expanding true leaves. Weeds 
at this time will not be more than 1.5” high. It is important to obtain maximum control of the earliest weed 
flush. Time the cultivation to give maximum control of regrowth or secondary weed flushes. Ultra Blazer 
will suppress or partially control weeds growing under conditions of high soil moisture and high relative 
humidity. 
c Partial control of wild buckwheat and buffalobur can usually be obtained when the seedlings have fewer 
than 2 true leaves. Use Ultra Blazer in 30 gallons of water per acre plus surfactant. 
d Members of the cucumber family germinate over an extended period of time. Therefore, control is 
difficult to obtain with a single spray. For Ultra Blazer to be effective, make the initial application to 
weeds no later than the 2-leaf growth stage. 
e Use 1.5 pints of Ultra Blazer herbicide per acre and 2 pints of spray surfactant per 100 gallons of spray 
mix unless otherwise stated. Activity depends on good soil moisture during and after the spray 
applications. 
f Sesbania and crotalaria are very sensitive to Ultra Blazer. Apply 1 pint of Ultra Blazer per acre. Effective 
control can be obtained at just about all plant heights; however, it is important that Ultra Blazer be applied 
prior to bloom. Do not apply after bloom as such applications are usually not effective. To control these 
weeds, time the application to occur after maximum weed emergence has taken place. Care must be 
exercised to make certain that crop canopies do not shade this weed from spray deposits. Waiting for the 
sesbania to break through the crop canopy may be advisable to control late season infestations. 
g Suppression or partial control. 
h More consistent control of morningglories can be achieved by using sequential applications of 1 pint of 
Ultra Blazer. 
i The labeled application of Ultra Blazer will usually kill or severely stunt wild poinsettia. Apply before the 
third true leaf has formed. This treatment will usually cause a height differential between soybeans and 
surviving wild poinsettia which will allow directed applications and even greater control. 
j The labeled application of Ultra Blazer will kill or suppress seedlings that are not past the 2-leaf stage. 
Applications after the 2-leaf stage are usually ineffective. 
k Use AMS (or UAN) as the additive when velvetleaf is a target weed. 
l Ultra Blazer must not be the basic component of a grassy weed or volunteer small grains management 
program. Ultra Blazer will kill or stunt many emerging volunteer small grains or grassy weeds in the 1-2 
leaf stage. Ultra Blazer can be used for additional control of escaped grasses and volunteer grains 
following a pre-plant incorporated or pre-emergence herbicide.

Ultra Blazer label edamame Rev.2/25/22 Page 18 
 
m Growth of perennial weeds from underground rootstocks is very difficult to control. Apply Ultra Blazer 
as listed above with 2-4 pints of spray surfactant per 100 gallons of spray mix to burn back the above-
ground plant parts and retard regrowth. Ultra Blazer will not kill the underground rootstocks of these 
weeds. 
 
 
STORAGE AND DISPOSAL 
Do not contaminate water, food, or feed by storage or disposal. 
Pesticide Storage: Do not store below 32ºF. 
Pesticide Disposal: Pesticide wastes are acutely hazardous. Improper disposal of excess pesticide, 
spray mix, or rinsate is a violation of federal law. If these wastes cannot be disposed of according to 
label instructions, contact the state agency responsible for pesticide regulation or the Hazardous 
Waste representative at the nearest EPA Regional Office for guidance. 
Container Handling: Nonrefillable container. Do not reuse or refill this container. Clean container 
promptly after emptying. 
[for containers less than or equal to 5 gallons] Triple rinse as follows: empty the remaining contents 
into application equipment or a mix tank and drain for 10 seconds after the flow begins to drip. Fill the 
container ¼ full with water and recap. Shake for 10 seconds. Pour rinsate into application equipment 
or a mix tank or store rinsate for later use or disposal. Drain for 10 seconds after the flow begins to 
drip. Repeat this procedure two more times. 
[for containers greater than 5 gallons] [Triple rinse or pressure rinse as follows: 
Triple rinse: Empty the remaining contents into application equipment or a mix tank. Fill the container 
¼ full with water. Replace and tighten closures. Tip container on its side and roll it back and forth, 
ensuring at least one complete revolution, for 30 seconds. After 30 seconds, stand the container over 
on its end and tip it back and forth several times. Empty the rinsate into application equipment or a mix 
tank or store rinsate for later use or disposal. Repeat this procedure two more times. 
Pressure rinse: Empty the remaining contents into application equipment or a mix tank and continue to 
drain for 10 seconds after the flow begins to drip. Hold container upside down over application 
equipment or mix tank or collect rinsate for later use or disposal. Insert pressure rinsing nozzle in the 
side of the container, and rinse at about 40 PSI for at least 30 seconds. Drain for 10 seconds after flow 
begins to drip.] 
[all sizes] Then offer for recycling, if available, or puncture and dispose of in a sanitary landfill, or by 
other procedures approved by state and local authorities. If rinsate cannot be used, follow pesticide 
disposal instructions. If not triple rinsed, these containers are acute hazardous wastes and must be 
disposed of in accordance with local, state and federal regulations. 
 
Steps to be taken in case material is released or spilled: 
Dike and contain the spill with inert material (sand, earth, etc.) and transfer liquid and solid diking 
material to separate containers for disposal. Remove contaminated clothing, and wash affected skin 
areas with soap and water. Wash clothing before re-use. Keep the spill out of all sewers and open 
bodies of water.

Ultra Blazer label edamame Rev.2/25/22 Page 19 
 
 
 
IMPORTANT INFORMATION 
READ BEFORE USING PRODUCT 
 
CONDITIONS OF SALE AND LIMITATION OF WARRANTY AND LIABILITY 
 
NOTICE: Read the entire Directions for Use and Conditions of Sale and Limitation of Warranty and 
Liability before buying or using this product. If the terms are not acceptable, return the product at 
once, unopened, and the purchase price will be refunded. 
 
The Directions for Use of this product reflect the opinion of experts based on field use and tests, and 
must be followed carefully. It is impossible to eliminate all risks associated with the use of this 
product. Crop injury, ineffectiveness or other unintended consequences may result because of such 
factors as manner of use or application, weather or crop conditions, presence of other materials or 
other influencing factors in the use of the product, which are beyond the control of UPL NA Inc. or 
Seller. Handling, storage, and use of the product by Buyer or User are beyond the control of UPL NA 
Inc. and Seller. All such risks shall be assumed by Buyer and User, and Buyer and User agree to 
hold UPL NA Inc. and Seller harmless for any claims relating to such factors. 
 
TO THE EXTENT CONSISTENT WITH APPLICABLE LAW, UPL NA INC. AND SELLER MAKE 
NO WARRANTIES OF MERCHANTABILITY OR OF FITNESS FOR A PARTICULAR PURPOSE 
NOR ANY OTHER EXPRESS OR IMPLIED WARRANTY EXCEPT AS STATED ON THIS LABEL. 
 
To the extent consistent with applicable law, UPL NA Inc. or Seller shall not be liable for any 
incidental, consequential or special damages resulting from the use or handling of this product and 
THE EXCLUSIVE REMEDY OF THE USER OR BUYER, AND THE EXCLUSIVE LIABILITY OF 
UPL NA INC. AND SELLER FOR ANY AND ALL CLAIMS, LOSSES, INJURIES OR DAMAGES 
(INCLUDING CLAIMS BASED ON BREACH OF WARRANTY, CONTRACT, NEGLIGENCE, 
TORT, STRICT LIABILITY OR OTHERWISE) RESULTING FROM THE USE OR HANDLING OF 
THIS PRODUCT, SHALL BE THE RETURN OF THE PURCHASE PRICE OF THE PRODUCT OR, 
AT THE ELECTION OF UPL NA INC. OR SELLER, THE REPLACEMENT OF THE PRODUCT. 
 
UPL NA Inc. and Seller offer this product, and Buyer and User accept it, subject to the foregoing 
conditions of sale and limitations of warranty and of liability, which may not be modified except by 
written agreement signed by the duly authorized representative of UPL NA Inc. 
 
UPL, the UPL logo, Ultra Blazer, Storm, and Stam are registered trademarks of a UPL Corporation 
Limited Group Company. 
All other products are trademarks of their respective companies. 
 
 
 
 
 
Ultra Blazer (PENDING) Submitted 02/25/22, Resubmitted 06/08/23, 06/22/23, 06/28/23, 07/03/23, 07/05/23, 
07/06/23, 07/11/23

ULTRA BLAZER® Herbicide 
(EPA Reg. No. 70506-60) 
 
FOR USE ON EDAMAME (vegetable soybean) 
DANGER/PELIGRO 
DIRECTIONS FOR USE 
It is a violation of Federal law to use this product in a manner inconsistent with its labeling. 
 
This supplemental label expires 08/01/2026 and must not be used or distributed after this date. 
 
Read the label affixed to the container for Ultra Blazer Herbicide before applying. Use of Ultra Blazer Herbicide 
according to this labeling is subject to the use precautions and limitations imposed by the label affixed to the 
container for Ultra Blazer Herbicide. This supplemental label, the label affixed to the container and the approved 
label must be in the possession of the user at the time of pesticide application. 
 
EDAMAME (VEGETABLE SOYBEAN) edible podded or succulent shelled 
Apply by ground only. Apply 1.0 pint of Ultra Blazer herbicide (0.25 lb ai)/A in sufficient water for uniform 
coverage (minimum of 10 gal/A) to control broadleaf weeds including glyphosate-tolerant amaranth, up 
to the R2 stage of growth. An adjuvant can be applied at a rate recommended by the adjuvant label. 
 
Restrictions 
• Do not make more than one application of Ultra Blazer herbicide per year. 
• Do not apply more than 1.0 pint (0.25 lbs ai)/A in a single application. 
• Do not make more than 1.0 pint (0.25 lbs ai)/A per year 
• Do not apply later than the R2 stage of growth. 
• Do not use treated plants for feed or forage. 
• Do not apply within 35 days before harvest. 
• Do not apply by air 
• Do not apply by handheld application equipment 
• Crop Rotation Restriction: In case of crop failure, only edamame (vegetable soybean), 
peanuts, soybeans, Strawberries and Low Growing Berries (crop subgroup 13-07G) or rice 
may be immediately replanted. Small grains must not be planted in fields treated with Ultra 
Blazer for 40 days following treatment. All other rotated crops must not be planted in fields 
treated with Ultra Blazer for 100 days following treatment. 
 
 
 
 
 
 
 
UPL NA Inc. 
630 Freedom Business Center, Suite 402 
King of Prussia, PA 19406 
1-800-673-6671 
Supplemental Label 
07/27/2023
70506-60