crop-chem-docs/corpus/epa_ppls/71711-42.md

# NAI-1295-2 HERBICIDE/DEFOLIANT

- EPA Reg No: **71711-42**
- Registrant: NICHINO AMERICA, INC.
- Signal word: Danger
- Active ingredients: Pyraflufen-ethyl (2.5%)
- Label accepted: 2013-01-17
- Source PDF: https://www3.epa.gov/pesticides/chem_search/ppls/071711-00042-20130117.pdf

---
U.S. ENVIRONMENTAL PROTECTION
AGENCY
Office of Pesticide Programs
Registration Division (7505P)
Ariel Rios Building
1200 Pennsylvania Ave., NW
Washington, D.C. 20460
NOTICE OF PESTICIDE:
x Registration
Reregistration
(under FIFRA, as amended)
EPA Reg. Number:
71711-42
Date of Issuance:
11
Term of Issuance: unconditional
Name of Pesticide Product:
NAI-1295-2
Herbicide/Defoliant
Name and Address of Registrant (include ZIP Code):
Nichino America, Inc.
4550 New Linden Hill Road, Suite 501
Wilmington, DE 19808 __^_
On the basis of information furnished by the registrant, the above named pesticide is hereby registered/reregistered under the Federal Insecticide,
Fungicide and Rodenticide Act. Registration is in no way to be construed as an endorsement or recommendation of this product by the Agency. In order
to protect health and the environment, the Administrator, on his motion, may at any time suspend or cancel the registration of a pesticide in accordance
with the Act. The acceptance of any name in connection with the registration of a product under this Act is not to be construed as giving the registrant a
right to exclusive use of the name or to its use if it has been covered by others.
The basic formulation (dated June 18, 2012) is acceptable and will be added to your file.
This product is registered in accordance with FIFRA section 3(c)(5) provided that you:
1. Submit and/or cite all data required for registration review/reregistration of your product when the
Agency requires all registrants of similar products to submit data.
2. Make the following label revision(s):
a. Revise "EPA Reg. No.71711-" to "EPA Reg. No. 71711-42."
b. Assure that the net contents are also added to the final printed label.
3. Within one year of the date on this registration notice, the Storage Stability (830.6317) and
Corrosion Characteristics (830.6320) studies must be submitted. They must be conducted in the
commercial containers of this product and observations should be made at 0, 3, 6, 9, and 12
month intervals.
4. Per 40 CFR 156.10(6), submit one copy of your final printed labeling before you release the
product for shipment.
If these conditions are not complied with, the registration will be subject to cancellation in accordance with
FIFRA sec.6(e). Your release for shipment of the product constitutes acceptance of these conditions. A
stamped copy of the label is enclosed for your records. If you have any questions regarding this notice, please
contact Beth Benbow of my staff at benbow.bethany@epa.gov.
Signature of Approving Official:
Kathryn V. Montague
Project Manager 23 L
Herbicide Branch
Registration Division (7505P)
M
Date:
JAN 1 12013
EPA Form 8570-6

NAM 295-2 Herbicide/Defoliant
A Contact Herbicide for Broadleaf Weed Control, Defoliation, and Desiccation
Active Ingredient: j
Pyraflufen ethyl: ethyl 2-chloro-5-(4-chloro-5-difluoromethoxy-1- i "-
methyl- 1H-pyrazol-3-yl)-4-fluorophenoxyacetate 2.5% : ^
Other Ingredients*: 97.5%
Total: : ,100.0% . ""•-•"
"contains petroleum distillates, xylene or xylene range aromatic solvents ' :
Contains 0.192 Ib. pyraflufen ethyl per gallon
JAN 1 7 2013
; _v pssioife
EPA Reg. No. 71711- EPA Est. No.: 70815-GA-002
KEEP OUT OF REACH OF CHILDREN
DANGER - PELIGRO
Si usted no entiende la etiqueta, busque a alguien para que se la explique a usted en detalle.
(If you do not understand the label, find someone to explain to you in detail.)
FIRST AID .
If. in eyes
If on skin
or
clothing
If
swallowed
If inhaled
• Immediately hold eye open and rinse slowly and gently with water for 15-20
minutes. Remove contact lenses, if present, after the first 5 minutes, then continue
rinsing eye.
• Call a poison control center or doctor for treatment advice
• Take off contaminated clothing.
• Rinse skin immediately with plenty of water for 15-20 minutes.
• Call a poison control center or doctor for treatment advice.
• Call a doctor or poison control center immediately for treatment advice.
• Do not give any liquid to the person.
• Do not induce vomiting unless told to do so by the poison control center or doctor.
• Do not give anything by mouth to an unconscious person.
• Move person to fresh air.
• If person is not breathing, call 91 1 or an ambulance, then give artificial respiration,
preferably mouth-to-mouth, if possible.
• Call a poison control center or doctor for further treatment advice.
HOTLINE NUMBER
Have the product container or label with you when calling a poison control center or doctor, or going
for treatment. You may also contact 1-800-348-5832 for emergency medical treatment information.
In case of fire or spills, information may be obtained by calling 1-800-424-9300.
NOTE TO PHYSICIAN
Contains petroleum distillates. Vomiting may cause aspiration pneumonia. Probable mucosal
damage may contraindicate the use of gastric lavage.
Net Contents:
Active Ingredient Made in Japan; Formulated and Packaged in U.S.A.
Nichino America, Inc.
4550 New Linden Hill Road, Suite 501
Wilmington, DE 19808
NAI-1295-2 061512
Page 1 of 22

(' .
PRECAUTIONARY STATEMENTS
HAZARDS TO HUMANS AND DOMESTIC ANIMALS
DANGER - PELIGRO
Corrosive. Causes irreversible eye damage. Do not get in eye, on skin, or on clothing. Wear
goggles or face shield when handling. Wash thoroughly with soap and water after handling and
before eating, drinking chewing gum, using tobacco or using the toilet. Remove and wash
contaminated clothing before reuse.
Personal Protective Equipment (PPE)
Some of the materials that are chemical-resistant to this product are listed below. If you want more
options, follow the instructions for Category B on an EPA chemical-resistance category selection
chart.
Applicators and other handlers must wear:
• Long-sleeved shirt and long pants
• Chemical resistant (such as barrier lamionate or butyl rubber >14 mils) gloves
• Shoes plus socks
• Protective eyewear
• For overhead exposure, wear chemical resistant headgear
Follow manufacturer's instructions for cleaning/maintaining PPE. If no such instructions for
washables exist, use detergent and hot water. Keep and wash PPE separately from other laundry.
When handlers use closed systems, enclosed cabs, or aircraft in a manner that meets the
requirements listed in the Worker Protection Standard (WPS) for agricultural pesticides [40 CFR
170.240 (d) (4-6)], the handler PPE requirements may be reduced or modified as specified in the
WPS.
User Safety Recommendations
Users should:
• Wash hands before eating, drinking, chewing gum, using tobacco, or using the toilet.
• Remove clothing immediately if pesticide gets inside. Then wash thoroughly and put on
clean clothing. ^^_^
ENGINEERING CONTROLS STATEMENTS
When handlers use closed systems, enclosed cabs, or aircraft in a manner that meets the
requirements listed in the Worker Protection Standard (WPS) for agricultural pesticides (40 CFR
170.240(d)(4-6), the handler PPE requirements may be reduced or modified as specified in the WPS.
ENVIRONMENTAL HAZARDS
This pesticide is toxic to fish and aquatic invertebrates. This product may contaminate water through
drift of spray in wind or via runoff events. Use care when applying in areas adjacent to any body of
water. Do not apply directly to water, to areas where surface water is present, or to intertidal areas
below the mean high water mark. Do not contaminate water when disposing of equipment washwater
or rinsate. Do not apply when weather conditions favor drift from treated areas. Do not apply if
rainfall is expected within one hour.
DIRECTIONS FOR USE
It is a violation of Federal law to use this product in a manner inconsistent with its labeling.
NAI-1 295-2 061812
Page 3 of 22

DO NOT apply this product in a way that will contact workers or other persons, either directly or
through drift. Only protected handlers may be in the area during application. For any requirements
specific to your State or Tribe, consult the agency responsible for pesticide regulation.
AGRICULTURAL USE REQUIREMENTS
Use this product only in accordance with its labeling and with the Worker Protection Standard, 40
CFR Part 170. This Standard contains requirements for the protection of agricultural workers on
farms, forests, nurseries, and greenhouses, and handlers of agricultural pesticides. It contains
requirements for training, decontamination, notification, and emergency assistance. It also contains
specific instructions and exceptions pertaining to the statements on this label about personal
protective equipment (PPE) and restricted-entry interval. The requirements in this box only apply to
uses of this product that are covered by the Worker Protection Standard.
DO NOT enter or allow worker entry into treated areas during the restricted entry interval (REI) of 12
hours.
PPE required for early entry to treated areas that is permitted under the Worker Protection Standard
and that involves contact with anything that has been treated, such as plants, soil, or water, is:
• Coveralls
. • Chemical resistant (such as nitrile or butyl) gloves
• Shoes plus socks
• Protective eyewear
NONAGRICULTURAL USE REQUIREMENTS
The requirements in this box apply to uses of this product that are NOT within the scope of the
Worker Protection Standard for agricultural pesticides (40 CFR Part 170). The WPS applies
when this product is used to produce agricultural plants on farms, forests, or greenhouses. For
other uses, including interiorscapes and other nonagricultural uses, do not enter treated areas
without protective clothing until sprays have dried.
USE INFORMATION
NAI-1295-2 Herbicide/Defoliant is designed for use as a contact herbicide for control of annual or
perennial herbaceous broad leaf weeds less than 4 inches in height, or rosettes less than 3 inches in
diameter. Use the higher rates and spray volumes for control of larger weeds; control may be reduced
with weeds larger than 4 inches.
NAI-1295-2 Herbicide/Defoliant must be tank mixed with another foliar active broadleaf herbicide for
complete control of most broadleaf weeds. This product requires thorough coverage for effective
control.
Use an approved agriculture buffering agent, buffering to less than pH 7.5, if using NAI-1295-2
Herbicide/Defoliant in a water source greater than or equal to pH 7.5. Always buffer the water source
BEFORE adding NAI-1295-2 Herbicide/Defoliant to the spray tank.
Do not apply this product through any type of irrigation system.
NAI-1295-2 Herbicide/Defoliant is rainfast within one hour after application.
NAI-1295-2 061812
Page 4 of 22

r
ROTATIONAL CROP RESTRICTIONS
Crop/Crop Group Rotational/Plantback Intervals
Corn
Cotton
Grapes
Olives
Pome Fruit Crop Group 11
Pomegranates
Potatoes
Soybeans
Stone Fruit Crop Group 12
Tree nuts Crop Group 14
Wheat, Triticale
0 days following application
Bulb Vegetables Crop Group 3
Cereal Grains Crop Group 15 (except corn,
wheat and Triticale - see 0 day plant back
interval above)
Cole Crops Crop Group 5
Cucurbits Crop Group 9
Fruiting Vegetables Crop Group 8
Leafy Vegetables Crop Group 4
Legumes Crop Group 6
Oil Seeds Crop Group 20
Root and Tuber Vegetables Crop Group 1
(except potato - see 0 day plant back interval
above)
Sugarcane
1 day following preplant burndown application
All other crops/crop groups, including hops 30 days following application
WEEDS CONTROLLED
The following broadleaf weed species can be controlled or suppressed up to 4 inches in height or
less, or rosettes of 3 inches in diameter or less. Tank mixtures of NAI-1295-2 Herbicide/Defoliant
with other labeled broadleaf herbicides may be needed for control of some weed species.
Amaranth, Palmer
Bedstraw
Beggarweed, Florida
Beggartick, hairy
Bindweed, field
Buckwheat, wild
Canola
Carpetweed
Celery, wild
Chickweed
Chickweed, common
Clover, white
Cocklebur
Dandelion, common
Knotweed, prostrate
Kochia
Ladysthumb
Lambsquarters, common
Lettuce, prickly
Mallow, common
Marestail (suppression)
Milkthistle
Morningglory, species
Mustard, wild (suppression)
Nettle, stinging
Nightshade, black
Panicle Willowweed
Pigweed, redroot
Ragweed, common
Ragweed, giant
Redmaid
Rocket, London
Sesbania, hemp
Shepherd's-purse
Sicklepod (suppression)
Smartweed, Pennsylvania
Smellmelon
Sowthistle, annual
Spurge, leafy
Sunflower, common
Thistle, Canada
Thistle, Russian __
NAi-1295-2 061812
Page 5 of 22

Dock, curly
Dollarweed
Eclipta
Evening primrose,
cutleaf
Geranium, Carolina
Henbit
Horsenettle
(suppression)
Pigweed, smooth
Pineapple weed
Poinsettia, wild
Poison-ivy
Prickly sida (Teaweed)
Purslane, common
Radish, wild
Toadflax, Dalmatian
Velvetleaf
Virginia-creeper
Volunteer cotton (Conventional,
GMO Varieties)
Waterhemp, tall
Waterhemp, common
Western tansymustard
TANK MIXTURES
NAI-1295-2 Herbicide/Defoliant may be applied as a tankmix or in sequential application with other
harvest aid, fungicide, insecticide or herbicide products. Weather, crop conditions, or the presence of
certain weeds, crop damaging insects, or diseases will indicate the inclusion of other pesticides in the
defoliation or desiccation application. Apply with grass herbicides if grassy weeds are present.
Note: It is recommended that the compatibility of NAI-1295-2 Herbicide/Defoliant in any tankrriix
combination be tested before use. To determine the physical compatibility with other products, use a
jar test, as described below.
Using a quart jar, add the proportionate amounts of the products to 1 qt. of water. Add wettable
powders and water-dispersible granular products first, then liquid flowables, and emulsifiable
concentrates last. After thoroughly mixing, let stand for at least 5 minutes. If the combination
remains mixed or can be remixed readily, it is physically compatible. Once compatibility has been
proven, use the same procedure for adding required ingredients to the spray tank.
Read and follow all label directions for each tankmix product. Always use in accordance with
the most restrictive of label precautions and limitations.
MIXING DIRECTIONS
Add 1/2 to % of the required amount of water to the spray tank. Start agitation. Add the required
amount of NAI-1295-2 Herbicide/Defoliant and the remaining amount of water. Mix only as much
spray solution as can be sprayed within four hours. Storage and use of the previous day's spray mix
may result in reduced activity.
Use an approved agriculture buffering agent, buffering to less than pH 7.5, if using NAI-1295-2
Herbicide/Defoliant in a water source greater than or equal to pH 7.5. Always buffer the water source
BEFORE adding NAI-1295-2 Herbicide/Defoliant to the spray tank.
SPRAY DRIFT
Avoid spray drift to all other crops and nontarget areas. Do not apply when weather conditions may
cause drift. Do not allow this product to drift onto nontarget areas. Drift may result in illegal residues
or injury to adjacent crops and vegetation, in the form of leaf yellowing and defoliation. To avoid
spray drift, DO NOT apply aerially when wind speed is greater than 10 mph or during periods of
temperature inversions. Use of larger droplet size will also reduce spray drift.
AVOIDING SPRAY DRIFT AT THE APPLICATION SITE IS THE RESPONSIBILITY OF THE
APPLICATOR.
The interaction of equipment and weather-related factors determines the potential for spray drift. The
applicator is responsible for considering all these factors when making decisions. Droplet size, boom
height, and wind speed are the primary factors determining drift. The specific application conditions
required for the use of this product are described below.
Information on Droplet Size
NAI-1295-2 061812
Page 6 of 22

c
The most effective way to reduce drift potential is to apply large droplets. The best drift management
strategy is to apply the largest droplets that provide sufficient coverage and control. Applying larger
droplets reduces drift potential, but will not prevent drift if applications are made improperly, or under
unfavorable environmental conditions (see Wind, Temperature and Humidity, and Temperature
Inversions)
Controlling Droplet Size
Volume - Use high flow rate nozzles to apply the highest practical spray volume. Nozzles with
higher rated flows produce larger droplets.
Pressure - Do not exceed the nozzle'manufacturer's recommended pressures. For many nozzle
types, lower pressure produces larger droplets. When higher flow rates are needed, use higher flow
rate nozzles instead of increasing pressure.
Number of Nozzles - Use the minimum number of nozzles that provide uniform coverage.
Nozzle Orientation - Orienting nozzles so that the spray is released parallel to the airstream
produces larger droplets than other orientations and is the recommended practice. Significant
deflection from horizontal will reduce droplet size and increase drift potential.
Nozzle Type - Use a nozzle type that is designed for the intended application. With most nozzle
types, narrower spray angles produce larger droplets. Consider using low-drift nozzles. Solid stream
nozzles oriented straight back produce'the largest droplets and the lowest drift.
Maintenance of Nozzles - Periodic inspection and subsequent replacement of nozzles to ensure
proper chemical application is recommended.
Boom Length
For some use patterns, reducing the effective boom length to less than % of the wingspan or rotor
length may further reduce drift without reducing swath width.
Application Height
Applications should not be made at a height greater than 10 feet above the top of the largest plants
unless a greater height is required for aircraft safety. Making applications at the lowest height that is
safe reduces exposure of droplets to evaporation and wind.
Swath Adjustment
When applications are made with a crosswind, the swath will be displaced downwind. Therefore, on
the up and downwind edges of the field, the applicator must compensate for this displacement by
adjusting the path of the aircraft upwind. Swath adjustment distance should increase, with increasing
drift potential (higher wind, smaller drops, etc.)
Wind
Drift potential is lowest between wind speeds of 2-10 mph. However, many factors, including droplet
size and equipment type determine drift potential at any given wind speed. Application should be
avoided below 2 mph due to variable wind direction and high inversion potential. Note: Local terrain
can influence wind patterns. Every applicator should be familiar with local wind patterns and how
they affect spray drift.
Temperature and Humidity
When making applications in low relative humidity, set up equipment to produce larger droplets to
compensate for evaporation. Droplet evaporation is most severe when conditions are both hot and
dry.
Temperature Inversions
Applications should not occur during a temperature inversion because drift potential is high.
Temperature inversions restrict vertical air mixing, which causes small suspended droplets to remain
in a concentrated cloud. This cloud can move in unpredictable directions due to the light and variable
NAI-1295-2 061812
Page 7 of 22

winds common during inversions. Temperature inversions are characterized by increasing
temperatures with altitude and are common on nights with limited cloud cover and light to no wind.
They.begin to form as the sun sets and often continue into the morning. Their presence can be
indicated by ground fog; however, if fog is not present, inversions can also be identified by the
movement of smoke from a ground source or an aircraft smoke generator. Smoke that layers and
moves laterally in a concentrated cloud (under low wind conditions) indicates an inversion, while
smoke that moves upward and rapidly dissipates indicates good vertical air mixing.
Sensitive Areas
The pesticide should only be applied when the potential for drift to adjacent sensitive areas (e.g.
residential areas, bodies of water, known habitat for threatened or endangered species, nontarget
crops) is minimal (e.g. when wind is blowing away from the sensitive areas).
EQUIPMENT CLEANING
Do not allow the spray solution to dry in the application equipment. After application and
before using the sprayer equipment for any other applications, the sprayer must be
thoroughly cleaned. Applicators must ensure proper equipment clean-out for any other
products mixed with NAI-1295-2 Herbicide/Defoliant as provided on the other product label(s).
Immediately following application, clean all equipment thoroughly with detergent or a spray tank
cleaner and water as described below. Should residues of NAI-1295-2 Herbicide/Defoliant remain in
inadequately cleaned equipment, they may be released in subsequent applications and cause injury
to crops.
1. Drain sprayer tank, hoses, and spray boom and thoroughly rinse with clean water the inside of the
spray tank, sprayer hoses, boom, and nozzles to remove any sediment or residues.
2. Fill the tank 1/2 full with clean water, add the appropriate detergent (follow manufacturer's
directions for use). Fill tank to capacity and operate the sprayer with agitation for 15 minutes to
flush hoses, boom, and nozzles.
3. Drain the sprayer tank, lines, and booms. Rinse the tank with clean water and flush through the
hoses, boom, and nozzles. Remove and clean spray nozzles, tips, and screens.
4. Dispose of all cleaning solutions, rinsate, and washwaters in accordance with Federal, state, and
local regulations.
APPLICATION RATE CHART
CORN - (field corn, popcorn, seed corn, corn silage, corn stover)
Application Pest Rate/Acre Directions for Use
Preplan!
burndown
Listed
Broadleaf
Weeds
0.5 to 2.0
fl oz/acre
• Apply in a minimum of 5 gallons spray solution per acre by air
or 10 gallons spray solution per acre by ground.
• The addition of a spray tank adjuvant at a concentration of
0.5% to 2.0% is recommended for optimum weed control.
• Use the higher rate for hard to control weeds
• Refer to "Rotational Crop Restrictions" table above for crop
rotations/plantback restrictions.
• Do not apply more than 2.0 fl oz/acre per season prior to
planting and/or emergence of crop.
• Allow a minimum of 30 days between applications for this use.
• NAI-1295-2 061812
Paae 8 of 22

At Plant,
Before Crop
Emergence
Listed
Broadleaf
Weeds
0.5 to 2.0
fl oz/acre
i Apply ET Herbicide/Defoliant in a minimum of 5 gallons spray
solution per acre by air or 10 gallons spray solution per acre by
ground.
' Do not apply more than 2.0 fl oz/acre per season at plant
and/or emergence of crop.
> Allow a minimum of 30 days between applications for this use.
• The addition of a spray adjuvant at a concentration of 0.5% to
2.0% is recommended for optimum weed control.
Postemergence
Directed
Listed
Broadleaf
Weeds
0.5 to 1.0
fl oz/acre
• Do not apply postemergence to sweet corn.
• Apply in a minimum of 5 gallons spray solution per acre by air or
10 gallons spray solution per acre by ground.
• Do not use crop oils or crop oil concentrates for postemergence
applications
• Can be applied from crop emergence to the V4 growth stage.
• Some temporary herbicidal leaf speckling may appear on the
crop. This effect is transient and will NOT appear on new
growth.
• Use the higher rate for hard to control weeds.
• Refer to "Rotational Crop Restrictions" table above for crop
rotations/plantback restrictions.
• Do not apply more than 1.0 fl oz per acre per season for this
use.
• Do not make more than 2 applications per season for this use.
• Allow a minimum of 30 days between applications for this use.
• Do not harvest corn for silage within 50 days after last
application.
• Do not harvest corn for grain or stover within 90 days after last
application.
CORN (all uses)
• Do not apply more than 3.0 fl oz/acre per growing season for all
preplan! burndown, at plant, preemergence, and postemergence
.uses.
• Refer to "Rotational Crop Restrictions" table above for crop
rotations/plantback restrictions.
• Use the listed higher rates for hard to control weeds.
COTTON
Application
P replant
burndown,
At Plant,
Before Crop
Emergence
Pest
Listed
Broadleaf
Weeds
Rate/ Acre
0.5 to 2.0
fl oz/acre
Directions for Use
• Apply in a minimum of 5 gallons spray solution per acre by air
or 10 gallons spray solution per acre by ground.
• The addition of a spray tank adjuvant at a concentration of 0.5%
to 2.0% is recommended for optimum weed control.
• Use the higher rate for hard to control weeds.
• Refer to "Rotational Crop Restrictions" table above for crop
rotations/plantback restrictions.
• Do not apply more than 2.0 fl oz per acre per season for this
use.
• Allow a minimum of 30 days between applications for this use.
NAI-1295-2 061812
Page 9 of 22

Post-emergence Listed
Broadleaf
Weeds
1.0 to 2.0
fl oz/acre
• Do NOT apply by air for this use.
• Apply to cotton having less than 3 inches of stem bark using
hooded ground equipment only.
• Avoid .contact with desirable vegetation.
• Use the higher rate for hard to control weeds.
• Refer to "Rotational Crop Restrictions" table above for crop
rotations/plantback restrictions.
• Do not exceed 2.0 fl oz per acre per season for this use.
• Allow a minimum of 30 days between applications for this use.
• Do not apply within 7 days of harvest.
• Use the higher rate for hard to control weeds.
Postemergence
Layby
Listed
Broadleaf
Weeds
0.5 to 1.0
fl oz/acre
> Do NOT apply by air for this use.
' Apply when the cotton has attained an average height of 18
inches or more and having at least 3 inches of stem bark using
hooded or postdirected ground spray equipment only.
' Avoid contact with desirable vegetation.
i Use the higher rate for hard to control weeds.
• Refer to "Rotational Crop Restrictions" table above for crop
rotations/plantback restrictions.
Do not apply more than 1.0 fl oz per acre per season for this
use.
> Allow a minimum of 30 days between applications for this use.
• 'Do not apply within 7 days of harvest.
Defoliation Defoliation
of Cotton
1.5 to
2.75 fl
oz/acre
• Apply when sufficient open bolls (generally greater than 60%)
have developed to produce desired yield.
• Apply using 20 to 30 gallons of water per acre by ground or 5
gallons of water per acre by air.
• Adequate defoliation is generally achieved within 7 to 14 days
depending upon weather conditions.
• Refer to "Rotational Crop Restrictions" table above for crop
rotations/plantback restrictions.
• Do not exceed 2 applications or 5.5 fl oz per acre per season.
• Applications must be a minimum of 7 days apart.
• Do not apply within 7 days of harvest.
• May be tank mixed or applied in sequence with other defoliant
products such as but not limited to, Cyclone®, DBF®, Dropp®,
ethephon, Finish , Firstpick®, Folex®, Ginstar®, Gramoxone®,
and/or Roundup®.
All uses Do not apply more than 8.5 fl oz per acre per growing season to
cotton.
NAI-1295-2 061812
Paae 10 of 22

f
POTATOES
Application Pest Rate/Ac re Directions for Use
Desiccation Potato
Foliage
and
Vines
Listed
Broadleaf
Weeds
2.75 to 5.5
fl oz/acre
• Apply by air at 5 gallons per acre or 20 to 50 gallons per
acre by ground equipment.
• Apply as a foliar spray in the early stage of crop
senescence.
• A repeat application of NAI-1295-2 Herbicide/Defoliant
or another desiccant may be needed under certain
climatic conditions for complete desiccation.
•.Make 1 to 2 applications at a minimum 7 day interval.
• Do not exceed 2 applications or 11.0 fl oz per acre per
season for desiccation.
• Do not apply within 7 days of harvest.
• Refer to "Rotational Crop Restrictions" table above for crop
rotations/plantback restrictions.
SOYBEANS
Application Pest Rate/Ac re Directions for Use
Preplan!
burndown, At
plant, before
crop emergence
Listed
Broadleaf
Weeds
0.5 to 2.0
fl oz/acre
> Apply in a minimum of 5 gallons spray solution per acre by air
or 10 gallons spray solution per acre by ground.
• The addition of a spray tank adjuvant at a concentration of
0.5% to 2.0% is recommended for optimum weed control.
Use the higher rate for hard to control weeds.
Refer to "Rotational Crop Restrictions" table above for crop
rotations/plantback restrictions.
Do not apply more than 2.0 fl oz per acre per season for this
use.
1 Allow a minimum of 30 days between applications for this use.
Postemergence Listed
Broadleaf
Weeds
0.4 to 1.0
fl oz/acre
• Apply in a minimum of 5 gallons spray solution per acre by air
or 10 gallons spray solution per acre by ground.
• Do not use crop oils or crop oil concentrates for postemergence
applications.
• Can be applied from crop emergence to the V6 growth stage.
• Some temporary herbicidal leaf speckling may appear on the
crop. This effect is transient and will NOT appear on new
growth.
• Use the higher rate for hard to control weeds.
• Refer to "Rotational Crop Restrictions" table above for crop
rotations/plantback restrictions.
• Do not apply more than 1.0 fl oz per acre per season for this
use.
• Allow a minimum of 30 days between applications for this use.
• Do not make more than 2 applications per season for this use.
• Do not graze soybean forage or cut for hay within 7 days of last
application.
• Do not harvest soybeans for grain within 70 days after last
application.
SOYBEAN (all uses) Do not apply more than 3.0 fl oz/acre per growing season to
soybeans.
• Refer to "Rotational Crop Restrictions" table above for crop
rotations/plantback restrictions.
• Use the higher rate for hard to control weeds.
NAI-1295-2061812
Page 11 of 22

WHEAT, TRITICALE
Application Pest Rate/Ac re Directions for Use
Preplan!
burndown
Listed
Broadleaf
Weeds
0.5 to 2.0
fl oz/acre
• Apply in a minimum of 5 gallons spray solution per acre by air
or 10 gallons spray solution per acre by ground.
• The addition of a spray tank adjuvant at a concentration of
0.5% to 2.0% is recommended for optimum weed control.
• Use the higher rate for hard to control weeds.
• Refer to "Rotational Crop Restrictions" table above for crop
rotations/plantback restrictions.
• Do not apply more than 2.0 fl oz per acre per season for this
use.
• Allow a minimum of 30 days between applications for this use.
At Plant,
Before Crop
Emergence
Listed
Broadleaf
Weeds
0.5 to 2.0
fl oz/acre
• Apply NAI-1295-2 Herbicide/Defoliant in a minimum of 5
gallons spray solution per acre by air or 10 gallons spray
solution per acre by ground.
• Allow a minimum of 30 days between applications for this use.
• Do not apply more than 2.0 fl oz/acre per season prior to
planting and/or emergence of crop.
• The addition of a COC adjuvant at a concentration of 1.0% is
recommended for optimum weed control.
• Refer to "Rotational Crop Restrictions" table above for crop
rotations/plantback restrictions.
Postemergence Listed
Broadleaf
Weeds
0.5 to 1.0
fl oz/acre
• Apply in a minimum of 5 gallons spray solution per acre by air
or 10 gallons spray solution per acre by ground.
• Use nonionic surfactant at a concentration of 0.5% for optimum
weed control.
• Can be applied from crop emergence to the appearance of the
flag leaf. DO NOT apply if the flag leaf is visible.
• Some temporary herbicidal leaf speckling may appear on the
crop. This effect is transient and will NOT appear on new
growth.
• Use the higher rate for hard to control weeds.
• Refer to "Rotational Crop Restrictions" table above for crop
rotations/plantback restrictions.
• Do not apply more than 1.0 fl oz per acre for this use per
season.
• Do not apply more than 2 applications per season.
• Allow a minimum of 30 days between applications for this use.
• Do not harvest wheat or triticale for hay within 21 days of last
application.
• Do not harvest wheat or triticale for grain within 60 days after
last application.
WHEAT, TRITICALE
All uses
• Do not apply more than 3.0 fl oz/acre per growing season for all
preplant burndown, at plant, preemergence, and
postemergence uses.
NAI-1295-2 061812
Page 12 of 22

r
Crop
BULB
VEGETABLES
(Crop Group 3):
garlic, elephant
garlic, leek, dry bulb,
green and Welch
onion, shallot
CEREAL GRAINS
(Crop Group 15):
barley, buckwheat,
corn, pearl and proso
millet, oats, popcorn,
rice, rye, sorghum,
teosinte, triticale,
wheat, wild rice
COLE (BRASSICA)
CROPS (Crop
Group 5): broccoli,
Chinese broccoli,
broccoli raab,
Brussels sprouts,
cabbage, Chinese
cabbage both bok
choy and napa,
Chinese mustard
cabbage, cauliflower,
cavalo broccolo,
collards, kale,
kohlrabi, mizuna,
mustard greens,
mustard spinach,
rape greens
CUCURBITS (Crop
Group 9): chayote,
Chinese waxgourd,
citron melon,
cucumber, gherkin,
edible gourd, balsam
apple, balsam pear,
bitter melon, Chinese
cucumber,
muskmelons
including
cantaloupe, casaba,
crenshaw melon,
golden perhsaw
melon, honeydew
melon, honey balls,
mango melon,
Persian melon,
Application
Pre-plant
Burndown
Pest
Listed
Broadleaf
Weeds
Rate/
Acre
0.5 to 2.0
fl oz/acre
Directions for Use
• Apply in a minimum of 10 gallons
spray solution per acre by ground or 5
gallons water per acre by air.
• The addition of nonionic surfactant
'at a concentration of 0.25% or COC at
1.0% is recommended for optimum
weed control.
• Use the higher rate for hard to
control weeds.
• Refer to "Rotational Crop Restrictions"
table above for crop rotations/plantback
restrictions.
• Do not exceed 3 applications or 5.5
fl oz per acre per season.
• Allow a minimum of 30 days
between applications for this use.
NAI-1295-2 061812
Page 13 of 22

pineapple melon,
Santa Glaus melon,
and snake melon,
pumpkin, winter and
summer squash
species, watermelon
FRUITING
VEGETABLES
(Crop Group 8):
eggplant, ground
cherry, pepino,
pepper, including
bell pepper, chili
pepper, cooking
pepper, pimento,
sweet pepper,
tomatillo, tomato
LEAFY
VEGETABLES
(Crop Group 4):
amaranth, arugula,
cardoon, celery,
Chinese celery,
celtuce, chervil,
edible-leaved
chrysanthemum,
corn salad, garden
cress, upland cress,
dandelion, dock,
endive, fennel,
lettuce, orach,
parsley, purslane,
radicchio, rhubarb,
spinach, swiss chard
LEGUME
VEGETABLES
(Crop Group 6):
beans, including
grain lupin, sweet
lupin, white lupin,
and white sweet
lupin, field bean,
kidney bean, lima
bean, navy bean,
pinto bean, runner
bean, snap bean,
Tepary bean, wax
bean, adzuki bean,
asparagus bean,
blackeyed pea,
catjang, Chinese
longbean, cowpea,
Crowder pea, moth
bean, mung bean,
rice bean, southern
-X
NAI-1295-2 061812
Page 14 of 22

r
pea, urd bean,
broadbean, yard-long
bean, broad bean,
chickpea, guar,
Jackbean, Lablab
bean, lentil, dwarf
pea, edible podded
pea, English pea,
field pea, garden pea,
green pea, snow pea,
sugar snap pea,
pigeon pea, soybean,
sword bean
OIL SEED CROPS
(Crop Group 20):
borage, calendula,
castor oil plant,
Chinese tallowtree,
cottonseed, crambe,
cuphea, echium,
euphorbia, evening
primrose, flax seed,
gold of pleasure,
Hare's ear mustard,
jojoba, lesquerella,
lunaria,
meadowfoam,
milkweed, mustard
seen, niger seed, oil
radish, poppy seed,
rapeseed [canola],
rose hip, safflower,
sunflower, sesame,
stokes aster, sweet
rocket, tallowwood,
tea oil plant, and
vernonia
ROOT AND TUBER
VEGETABLES
(Crop Group 1):
arracacha, arrowroot,
Chinese and
Jerusalem artichoke,
garden beet, sugar
beet, edible burdock,
edible canna, carrot,
bitter cassava, sweet
cassava, celeriac,
chayote, chervil,
chicory, chufa,
dasheen, ginger,
ginseng,
horseradish, leren,
parsley, parsnip,
potato, radish,
daikon, rutabaga,
\
NAI-1295-2 061812
Page 15 of 22

salsify, skirret, sweet
potato, tanier,
turmeric, turnip, yam
bean, true yam
SUGARCANE
\-\
Crop
GRAPES (bearing
and nonbearing)
OLIVE TREES
(bearing and
nonbearing)
POMEGRANATES
(bearing and
nonbearing)
POME FRUIT
(Crop Group 11)
(bearing and
nonbearing)
apple, crabapple,
loquat, mayhaw,
pear, pear
(oriental), quince
STONE FRUIT
(Crop Group 12)
(bearing and
nonbearing)
apricot, cherry
(sweet and tart),
nectarine, peach,
plum (including
chickasaw plum,
damson plum, and
Japanese plum),
plumcot, prune
TREE NUT (Crop
Group 14)
(bearing and
nonbearing)
almond, beech nut,
Brazil nut,
butternut, cashew,
chestnut,
chinquapin, filbert
(hazelnut),
macadamia nut,
pecan, pistachio,
walnut (black and
Application
Post-
harvest,
Dormant,
Prebloom
In-Season
Pest
Listed
Broadleaf
Weeds
Sucker
Management
Listed
Broadleaf
Weeds
Sucker
Management
Rate/ Ac re
0.8 to 3.25
fl oz/acre
3.25
fl oz/acre
0.8 to
3.25
fl oz/acre
3.25
fl oz/acre
Maximum
Applications
Rate/Year
Do not
exceed 3
applications
or 5.5 fl oz
per acre per
season for
these uses.
Do not
exceed 2
applications
or 5.5 fl oz
per acre per
season for
these uses.
Directions for Use
• Do not apply by air for
this use.
• Apply in a minimum of 20
gallons spray solution per
acre by ground equipment
to target weeds and sucker
growth.
• The addition of a spray
tank adjuvant at a
concentration of 0.5% to
2.0% is recommended for
optimum weed control.
• Do not allow spray to
drift onto desirable fruit,
foliage or vines, as damage
will occur.
•Avoid contact with green,
uncallused bark of young
vines established less than
one year, unless protected
from spray contact by non-
porous wraps, grow tubes,
or waxed containers.
• Use the higher rate for
hard to control weeds.
• Allow a minimum of 30
days between applications
for this use.
• For the management of
undesirable sucker growth
on the basal portion of
trunks, root sprouts and
vine trunks. Growth must
be controlled when the
tissue is young, immature
and/or not hardened off.
NAI-1 295-2 061812
Page 16 of 22

r
English)
Note: For use in California for sucker management only on Grapes, Stone Fruit,
Pome Fruit and Pomegranates. Not for use in California for sucker management
on Olive Trees and Tree Nuts.
Crop
DATES, FEIJOA,
FIGS, KIWI
FRUIT, MANGO,
PERSIMMON
(bearing and
nonbearing)
Application
Post-
harvest,
Dormant,
Prebloom
Pest
Listed
Broad leaf
Weeds
Sucker
Management
(Not for
sucker
management
use on these
crops in
California)
Rate/ Ac re
0.8 to 3.25
fl oz/acre
2.5 to 3.25
fl oz/acre
Maximum
Applications
Rate/Year
Do not
exceed 3
applications
per season
for this use.
Do not
exceed 2
applications
per season
for this use.
Directions for Use
• Do not exceed 5.5 fl oz
per acre per season for all
post-harvest, dormant, and
prebloom applications
combined.
• Do not apply by air for
this use.
• Apply in a minimum of
20 gallons spray solution
per acre by ground
equipment to target weeds
and sucker growth.
• The addition of a COC
adjuvant at a
concentration of 1.0% is
recommended for optimum
weed control.
• Do not allow spray to
drift onto desirable fruit,
foliage or vines/trees, as
damage will occur.
•Avoid contact with green,
uncallused bark of young
trees/vines, established
less than one year, unless
protected from spray
contact by non-porous
wraps, grow tubes, or
waxed containers.
• Use the higher rate for
hard to control weeds.
• Allow a minimum of 30
days between applications
for this use.
• For the management of
undesirable sucker growth
on the basal portion of
trunks, root sprouts and
tree/vine trunks. Growth
must be controlled when
the tissue is young,
immature and/or not
hardened off.
NAI-1295-2 061812
Page 17 of 22

Crop
DATES, FEIJOA,
FIGS, KIWI
FRUIT, MANGO,
PERSIMMON
(Nonbearing only)
Application
In-Season
Pest
Listed
Broad leaf
Weeds
Sucker
Management
(Not for
sucker
management
use on these
crops in
California)
Rate/ Ac re
0.8 to 3.25
fl oz/acre
2.5 to 3.25
fl oz/acre
Maximum
Applications
Rate/Year
Do not
exceed a
combined
total of 2
applications
per season
for these
uses.
Directions for Use
• Do not exceed 5.5 fl oz
per acre per season for all
. in season applications
combined.
• Do not apply by air for this
use.
• Apply in a minimum of 20
gallons spray solution per
acre by ground equipment
to target weeds and sucker
growth.
• The addition of a COC
adjuvant at a concentration
of 1.0% is recommended
for optimum weed control.
• Do not allow spray to drift
onto desirable fruit, foliage,
vines or trees, as damage
will occur.
•Avoid contact with green,
uncallused bark of young
trees or vines, established
less than one year, unless
protected from spray
contact by non-porous
wraps, grow tubes, or
waxed containers.
• Use the higher rate for
hard to control weeds.
• Allow a minimum of 30
days between applications.
• For the management of
undesirable sucker growth
on the basal portion of
trunks, root sprouts and
tree/vine trunks. Growth
must be controlled when the
tissue is young, immature
and/or not hardened off.
NAI-1295-2061812
Page 18 of 22

r
Crop
Nonbearing tree
fruit, Nut trees and
Vine crops
(Excluding citrus)
Application
Full season
weed control
Pest
Listed
broad leaf
weeds
Rate/ Ac re
0.5 to 2.0
fl oz/acre
Maximum
Applications
Rate/Year
Directions for Use
• Do not apply by air for this
use.
• Apply in a minimum of 20
gallons spray solution per
acre by ground equipment
to target weeds and sucker
growth.
• Do not make more than 3
applications or exceed 5.5 fl
oz per acre during the
growing season.
• The addition of a COC
adjuvant at a concentration
of 0.5% to 2.0% is
recommended for optimum
weed control.
• Do not allow spray to drift
onto desirable fruit, foliage,
vines or trees, as damage
will occur.
• Use the higher rate for
hard to control weeds.
• Allow a minimum of 30
days between applications.
• For crops not listed on
this label, do not harvest
edible crops for 12 months
following the last
application.
PREPLAN! BURNDOWN FALLOW BED AND CROP STUBBLE
Pest Rate/Ac re Directions for Use
Listed
Broadleaf
Weeds
0.5 to 2.0
fl oz/acre
• Apply in a minimum of 5 gallons spray solution by air and 10 gallons
per acre by ground.
• The addition of a spray tank adjuvant at a concentration of 0.5% to
2.0% is recommended for optimum weed control.
• Use the higher rate for hard to control weeds.
• Refer to "Rotational Crop Restrictions" table above for crop
rotations/plantback restrictions.
• Do not make more than 3 applications or exceed 5.5 fl oz per acre
during the fallow period.
• Allow a minimum of 30 days between applications for this use.
NAI-1295-2 061812
Page 19 of 22

NON-CROPLAND, UNCULTIVATED AGRICULTURAL AREAS, CONSERVATION RESERVE
PROGRAM LAND/FEDERAL SET-ASIDE ACREAGE* (NON FOOD PRODUCING)
Pest Rate/Ac re Directions for Use
Listed
Broadleaf
Weeds
0.5 to 2.0
fl oz/acre
• Apply NAI-1295-2 Herbicide/Defoliant in a minimum of 5 gallons of spray
solutionper acre by air or 10 gallons spray solution per acre by ground.
o Allow a minimum of 30 days between applications for this use.
• Do not make more than 3 applications or exceed 5.5 fl oz/acre during the
fallow period.
• The addition of a COG adjuvant at a concentration of 1.0% is recommended
for optimum weed control.
• Refer to "Rotational Crop Restrictions" table above for crop
rotations/plantback restrictions.
• Use the higher rate for hard to control weeds.
*Follow federal, state and local rules for use on grass and hay.
NONCROP WEED CONTROL:
AIRPORTS AND AIRFIELDS, COMMERCIAL PLANTS, STORAGE AND LUMBER YARDS,
FENCELINES AND FENCE ROWS, FARMYARDS AND FARM BUILDINGS, BARRIER STRIPS
AND FIREBREAKS, EQUIPMENT AREAS, NURSERIES AND ORNAMENTAL PLANTINGS,
CHRISTMAS TREES AND CONIFER PLANTATION SITE PREPARATION, RAILROADS,
ROADSIDE AND UTILITY RIGHTS-OF-WAY, FUEL TANK FARMS AND PUMPING STATIONS,
DRY DITCHES AND DITCHBANKS, VACANT LOTS, OR OTHER LISTED AGRICULTURAL AND
INDUSTRIAL NON-CROP SITES
Pest Rate/Ac re Directions for Use
Listed
Broadleaf
Weeds
0.5 to 2.75
fl oz/acre
• Apply NAI-1295-2 Herbicide/Defoliant in a minimum of 20 to 40 gallons
spray solution per acre by ground.
' Do not apply by air for this use.
> Avoid contact with desirable vegetation.
> The addition of a COC adjuvant at a concentration of 1.0% is
recommended for optimum weed control.
• Do not make more than 3 applications or exceed 9.7 fl oz/acre per season
using ground or backpack or similar spray equipment.
' Use the higher rate for hard to control weeds.
> For applications to ornamental plantings, do not allow people (other than
the applicator) or pets on treatment area during the application and until
sprays have dried.
ESTABLISHED ORNAMENTAL TURF LAWNS (RESIDENTIAL, INDUSTRIAL, AND
INSTITUTIONAL) PARKS, CEMETERIES, ATHLETIC FIELDS, GOLF COURSES (FAIRWAYS,
APRONS, TEES, AND ROUGHS), SOD FARMS, AND SIMILAR TURF AREAS
For applications to ornamental turf, do not allow people (other than the applicator) or pets on treatment area
during the application and until sprays have dried.
Spray Concentrate
Make an appropriate amount of spray concentrate for the area to be treated by adding 8 fl oz of ET
Herbicide/Defoliant to 120 fl oz of water (e.g., 1 fl oz ET Herbicide/Defoliant to 15 fl oz water, or 0.5 fl oz ET
Herbicide/Defoliant to 7.5 fl oz water). Use the appropriate amount of concentrate as specified in the dosage
tables below for application by pressure (pump-up) sprayer, hose-end applicator, or similar application
equipment.
Spot treatment: Pressure sprayer (Pump-up Sprayer)
Adjust spray nozzle to give coarse spray. Aim at center of weed and spray to wet. A repeat application may be
required for hard-to-kill broadleaf weeds. Do not use a hose-end sprayer for spot treatments.
NAI-1295-2 061812
Page 20 of 22

r
Turf Species
Cool season grasses:
bluegrass, fescue, ryegrass
Warm season grasses:
bahiagrass, common bermudagrass,
centipedegrass, St. Augustine grass,
zoysia grass
Amount of Spray
Concentrate (fl oz)
1.0
0.5
Amount of water to
be applied (gallons)
4
2
Area treated
(square feet)
1000
500
Entire lawn: Dial Type Hose-End Sprayer
Spray lawn using coarse spray. Apply evenly over area to be treated. One application should be sufficient.
Effects begin to show after 24 to 48 hours with plant death occurring within 7 to 14 days.
1) Measure the total square footage area to be sprayed. To determine the total square foot area, multiply the
length by the width of the lawn area to be treated. Subtract square footage of non-treatment areas
including flower beds, shrub beds, driveways and sidewalks.
2) The application rate of this product is indicated in the following table for every per 1,000 square feet of lawn
area. Add the appropriate amount of this product to the spray bottle, [jar], [reservoir], as indicated in the
table for every 1,000 sq. ft. of lawn area to be treated.
3) Set the dial to the correct fluid ounce setting mix rate indicated in the following table.
4) Connect the hose, turn on water and spray evenly over the lawn treatment area.
5) Monitor the spray solution level in the spray bottle, Oar], [reservoir], to gauge coverage.
Turf Species
Cool season grasses:
bluegrass, fescue,
ryegrass
Area to be Treated
(square feet)
1000
5000
8000
Amount of spray
concentrate (fluid ounces)
1.0
5.0
8.0
Dial-type Hose-end
sprayer mix setting
(fl oz per gallon)
2.0 fl oz
Broadcast Application: Spray using coarse spray. Apply evenly over area to be treated.
Turf Species
Cool season grasses: bluegrass, fescue, ryegrass
Warm season grasses: bahiagrass, common;
bermudagrass; centipedegrass; St Augustine
grass; zoysia grass
Amount of Spray Concentrate
(fluid ounces)
1.0
5.0
8.0
Area treated
(square feet)
1000
5000
8000
PASTURE AND RANGELAND
Pest Rate/Ac re Directions for Use
Listed
Broad leaf
Weeds
0.75 to 2.25
fl oz/acre
• Allow a minimum of 14 days between applications for this use.
• Do not make more than 2 applications or exceed 5.5 fl oz/acre per season
for this use.
• Livestock may graze treated areas as soon a the spray solution has dried
on the foliage.
• The addition of a crop oil or spray tank adjuvant at a concentration of 0.5%
to 1.0% is recommended for optimum weed control.
• Refer to "Rotational Crop Restrictions" table above for crop
rotations/plantback restrictions.
• Apply in a minimum of 2 gallons water per acre by air or 10 gallons water
per acre by ground for this application.
• Use the higher rate for hard to control weeds.
NAi-1295-2 061812
Page2l'of 22

r
STORAGE AND DISPOSAL
DO NOT contaminate water, food, or feed by storage or disposal. Open dumping is prohibited.
Pesticide Storage: Store in a cool place.
Pesticide Disposal: Pesticide wastes are toxic. Improper disposal of excess pesticide, pesticide
spray or rinsate is a violation of Federal law. If these wastes cannot be disposed of by use according
to label instructions, contact your State Pesticide or Environmental Control Agency, or the Hazardous
Waste representative at the nearest EPA Regional Office for guidance.
Container Disposal: Nonrefillable container. DO NOT reuse or refill this container. Triple rinse (or
equivalent) promptly after emptying. Triple rinse as follows: Empty the remaining contents into
application equipment or a mix tank and drain for 10 seconds after the flow begins to drip. Fill the
container % full with water and recap. Shake for 10 seconds. Pour rinsate into application equipment
or a mix tank or store rinsate for later use or disposal. Drain for 10 seconds after the flow begins to
drip. Repeat this procedure two more times. Then offer for recycling or reconditioning, or puncture
and dispose of in a sanitary landfill, or by incineration, or, if allowed by State or local authorities, by
burning. If burned, stay out of smoke.
IMPORTANT: READ BEFORE USE
By using this product, user or buyer accepts the following conditions, warranty, disclaimer of
warranties, and limitations of liability.
CONDITIONS: The directions for use of this product are believed to be accurate and must be
followed carefully. However, because of extreme weather and soil conditions, use methods and other
factors beyond the control of Nichino America, Inc. (NAI), it is impossible for NAI to eliminate all risks
associated with the use of this product. As a result, crop injury or ineffectiveness is always possible.
To the extent consistent with applicable law, all such risks are assumed by the user or buyer.
DISCLAIMER OF WARRANTIES: TO THE EXTENT CONSISTENT WITH APPLICABLE LAW,
THERE ARE NO WARRANTIES, EXPRESS OR IMPLIED, OF MERCHANTABILITY OR OF
FITNESS FOR A PARTICULAR PURPOSE OR OTHERWISE, WHICH EXTEND BEYOND THE
STATEMENTS MADE ON THIS LABEL. No agent of NAI is authorized to make any warranties
beyond those contained herein or to modify the warranties contained herein. To the extent consistent
with applicable law, NAI disclaims any liability whatsoever for incidental or consequential damages,
including, but not limited to, liability arising out of breach of contract, express or implied warranty
(including warranties of merchantability and fitness for a particular purpose), tort, negligence, strict
liability, or otherwise.
LIMITATIONS OF LIABILITY: TO THE EXTENT CONSISTENT WITH APPLICABLE LAW, THE
EXCLUSIVE REMEDY OF THE USER OR BUYER FOR ANY AND ALL LOSSES, INJURIES OR
DAMAGES RESULTING FROM THE USE OR HANDLING OF THIS PRODUCT, WHETHER IN
CONTRACT, WARRANTY, TORT, NEGLIGENCE, STRICT LIABILITY, OR OTHERWISE, SHALL
NOT EXCEED THE PURCHASE PRICE PAID, OR AT THE ELECTION OF NICHINO AMERICA,
THE REPLACEMENT OF PRODUCT.
©2010. Nichino America, Inc.
Cottonquik® is a trademark of duPont Corporation. Cyclone®, and Gramoxone®, are trademarks of
Syngenta Crop Protection. DEF® 6, Dropp® 50WP, Finish® , Ginstar®, and Prep™ are trademarks of
Bayer Crop Science. Roundup® is a trademark of Monstanto Company. Folex® 6EC is a trademark of
Amvac.
D-121 011713
NAI-1295-2 061812
Page 22 of 22