crop-chem-docs/corpus/epa_ppls/100-1613.md

# Trivapro® Fungicide

- EPA Reg No: **100-1613**
- Registrant: SYNGENTA CROP PROTECTION, LLC
- Signal word: Warning
- Active ingredients: Propiconazole (11.9%); Benzovindiflupyr (2.9%); Azoxystrobin (10.5%)
- Label accepted: 2024-10-30
- Source PDF: https://www3.epa.gov/pesticides/chem_search/ppls/000100-01613-20241030.pdf

---
1 
 
 
October 30, 2024 
 
Adora Clark, Ph.D. 
Fungicides Team Lead 
Syngenta Crop Protection, LLC 
P.O. Box 18300 
Greensboro, NC 27419 
 
Subject: PRIA Label Amendment – Reduced plant-back interval for “all other crops 
Intended for Food and Feed”. 
 Product Name: Trivapro Fungicide 
 EP A Registration Number: 100-1613 
 Application Date: 9/27/2023 
 Case Number: 492197 
 
Dear Adora Clark: 
 
The amended label referred to above, submitted in connection with registration under the 
Federal Insecticide, Fungicide, and Rodenticide Act (FIFRA), as amended, is acceptable. This 
approval does not affect any conditions that were previously imposed on this registration. You 
continue to be subject to existing conditions on your registration and any deadlines connected 
with them. 
 
The Agency, in accordance with FIFRA, as amended, has completed reviewing all of the 
information submitted with your application to support the Registration Review of the above 
referenced product in connection with the Azoxystrobin Final and/or Interim Decision, and has 
concluded that your submission is acceptable. 
 
The alternate brand name, “Tombolo”, has been added to the product record. 
 
A stamped copy of your labeling is enclosed for your records. This labeling supersedes all 
previously accepted labeling. You must submit one copy of the final printed labeling before you 
release the product for shipment with the new labeling. In accordance with 40 CFR 152.130(c), 
you may distribute or sell this product under the previously approved labeling for 12 months 
from the date of this letter. After 12 months, you may only distribute or sell this product if it 
bears this new revised labeling or subsequently approved labeling. “To distribute or sell” is 
defined under FIFRA section 2(gg) and its implementing regulation at 40 CFR 152.3.

Page 2 of 2 
EPA Reg. No. 100-1613 
Case No. 492197 
 
Should you wish to add/retain a reference to the company’s website on your label, then please 
be aware that the website becomes labeling under FIFRA and is subject to review by the 
Agency. If the website is false or misleading, the product would be misbranded and unlawful to 
sell or distribute under FIFRA section 12(a)(1)(E). 40 CFR 156.10(a)(5) lists examples of 
statements EPA may consider false or misleading. In addition, regardless of whether a website 
is referenced on your product’s label, claims made on the website may not substantially differ 
from those claims approved through the registration process. Therefore, should the Agency find 
or if it is brought to our attention that a website contains false or misleading statements or 
claims substantially differing from the EPA approved registration, the website will be referred 
to the EPA’s Office of Enforcement and Compliance. 
 
Your release for shipment of the product constitutes acceptance of these conditions. If these 
conditions are not complied with, the registration will be subject to cancellation in accordance 
with FIFRA section 6. 
 
If you have any questions, please contact Stephanie Suarez at 202-566-2918 or at 
suarez.stephanie@epa.gov. 
 
 Sincerely, 
 
 
 
 Cynthia L. Giles-Parker, Chief 
 Fungicide Branch 
 Registration Division (7505T) 
 
Enclosure -stamped “accepted” label

Trivapro Fungicide 
Page 1 
 
 
PROPICONAZOLE GROUP 3 FUNGICIDE 
BENZOVINDIFLUPYR GROUP 7 FUNGICIDE 
AZOXYSTROBIN GROUP 11 FUNGICIDE 
 
Trivapro® Fungicide 
 
[Alternate brand name: Tombolo] 
 
SOLATENOL® Technology* 
 
*Technology denotes the active ingredient, Benzovindiflupyr. 
 
Active Ingredients: 
Benzovindiflupyr**: .................................................................................................... 2.9% 
Azoxystrobin***: ...................................................................................................... 10.5% 
Propiconazole****: ................................................................................................... 11.9% 
Other Ingredients: 74.7% 
Total: 100.0% 
 
 **CAS No. 1072957-71-1 
 ***CAS No. 131860-33-8 
****CAS No. 60207-90-1 
 
Trivapro Fungicide is formulated as a suspo-emulsion and contains 0.25 lb of 
benzovindiflupyr, 0.92 lb of azoxystrobin, and 1.04 lb of propiconazole active ingredients 
per gallon. 
 
KEEP OUT OF REACH OF CHILDREN. 
 
WARNING/AVISO 
 
Si usted no entiende la etiqueta, busque a alguien para que se la explique a usted en 
detalle. (If you DO NOT understand the label, find someone to explain it to you in 
detail.) 
 
See additional precautionary statements and directions for use inside booklet. 
See First Aid statement inside booklet and on container label. 
 
EPA Reg. No. 100-1613 
EPA Est. 
[Batch Code: _____ ] (For nonrefillables only.) 
 
_____ gallons 
Net Contents 
 
10/30/2024
100-1613

Trivapro Fungicide 
Page 2 
 
TABLE OF CONTENTS 
 
1.0 FIRST AID 
2.0 PRECAUTIONARY STATEMENTS 
2.1 Hazards to Humans and Domestic Animals 
2.2 Personal Protective Equipment (PPE) 
2.2.1 Engineering Controls 
2.3 Environmental Hazards 
2.3.1 Groundwater Advisory 
2.3.2 Surface Water Advisory 
2.4 Physical or Chemical Hazards 
 
DIRECTIONS FOR USE 
 
3.0 PRODUCT INFORMATION 
3.1 Integrated Pest (Disease) Management (IPM) 
3.2 Resistance Management 
4.0 APPLICATION DIRECTIONS 
4.1 Methods of Application 
4.2 Application Equipment 
4.2.1 Nozzles 
4.2.2 Pumps 
4.3 Application Volume and Spray Coverage 
4.4 Mixing Directions 
4.4.1 Trivapro Fungicide Alone 
4.4.2 Tank-Mix Precautions 
4.4.3 Tank-Mix Compatibility Test 
4.4.4 Trivapro Fungicide in Tank Mixtures 
4.4.5 Spray Additives 
4.5 Application through Irrigation Systems (Chemigation) 
4.5.1 Application Directions for Overhead Irrigation Systems 
4.5.2 Operating Instructions for Chemigation 
4.5.3 Specific Instructions for Public Water Systems 
5.0 ROTATIONAL CROP RESTRICTIONS 
6.0 RESTRICTIONS AND PRECAUTIONS 
6.1 Use Restrictions 
6.1.1 Aerial Spray Restrictions 
6.2 Use Precautions 
6.3 Spray Drift Management 
6.3.1 Controlling Droplet Size – Groundboom 
6.3.2 Controlling Droplet Size – Aircraft 
6.3.3 Application Height 
6.3.4 Boom Height – Groundboom 
6.3.5 Release Height - Aircraft 
6.3.6 Shielded Sprayers 
6.3.7 Wind 
6.3.8 Temperature and Humidity 
6.3.9 Temperature Inversions 
6.3.10 Non-Target Areas

Trivapro Fungicide 
Page 3 
 
7.0 CROP USE DIRECTIONS 
7.1 Bulb Vegetables 
7.2 Rapeseed (Canola) Subgroup 20A 
7.3 Cereals 
7.4 Corn (except sweet) 
7.5 Corn, Sweet 
7.6 Beans, Dry and Succulent (except Soybean) 
7.7 Grasses Grown for Seed
 (bluegrass, bromegrass, fescue, orchardgrass, and 
ryegrass only) 
7.8 Peanut 
7.9 Soybean 
7.10 Sugarcane 
8.0 STORAGE AND DISPOSAL 
9.0 CONDITIONS OF SALE AND LIMITA TION OF WARRANTY AND LIABILITY 
10.0 APPENDIX 
10.1 Trivapro Fungicide Rate Conversion Chart 
10.2 [optional text] Trivapro Fungicide Use Summary Table

Trivapro Fungicide 
Page 4 
 
1.0 FIRST AID 
FIRST AID 
If in eyes  Hold eye open and rinse slowly and gently with water for 15-20 
minutes. Remove contact lenses, if present, after the first 5 
minutes, then continue rinsing eye. 
 Call a poison control center or doctor for treatment advice. 
If swallowed  Call a poison control center or doctor immediately for treatment 
advice. 
 Have person sip a glass of water if able to swallow. 
 DO NOT induce vomiting unless told to do so by a poison 
control center or doctor. 
 DO NOT give anything by mouth to an unconscious person. 
If on skin  Take off contaminated clothing. 
 Rinse skin immediately with plent y of water for 15-20 minutes. 
 Call a poison control center or doctor for treatment advice. 
If inhaled  Move person to fresh air. 
 If person is not breathing, call 911 or an ambulance, then give 
artificial respiration, preferably mouth-to-mouth if possible. 
 Call a poison control center or doctor for further treatment 
advice. 
Have the product container or label with you when calling a poison control center or 
doctor or going for treatment. 
HOTLINE NUMBER 
For 24-Hour Medical Emergency Assistance (Human or Animal) 
Or Chemical Emergency Assistance (Spill, Leak, Fire or Accident) 
Call 
1-800-888-8372 
 
2.0 PRECAUTIONARY STATEMENTS 
2.1 Hazards to Humans and Domestic Animals 
 
WARNING/AVISO 
 
Causes substantial but temporary eye injury. Harmful if swallowed. Harmful if 
absorbed through skin. Avoid contact with skin. Wear protective eyewear. DO NOT 
get in eyes or on clothing. Wash thoroughly with soap and water after handling and 
before eating, drinking, chewing gum, using tobacco or using the toilet. Remove and 
wash contaminated clothing before reuse.

Trivapro Fungicide 
Page 5 
 
2.2 Personal Protective Equipment (PPE) 
Applicators and other handlers must wear: 
 Long-sleeved shirt and long pants 
 Chemical-resistant gloves: barrier laminate, butyl rubber ≥ 14 mils, nitrile rubber ≥ 
14 mils, neoprene rubber ≥ 14 mils, natural rubber ≥ 14 mils, polyethylene, polyvinyl 
chloride ≥ 14 mils, or Viton™ ≥ 14 mils. 
 Shoes plus socks 
 Protective eyewear (goggles, face sh ield, or shielded safety glasses) 
 
User Safety Requirements 
 
Discard clothing and other absorbent materials that have been drenched or heavily 
contaminated with this product’s concentrate. Follow the manufacturer’s instructions 
for cleaning/maintaining PPE. If no such instructions for washables exist, use 
detergent and hot water. Keep and wash PPE separately from other laundry. 
 
2.2.1 ENGINEERING CONTROLS 
When handlers use closed systems, enclosed cabs, or aircraft in a manner that meets 
the requirements listed in the Worker Protection Standard (WPS) for agricultural 
pesticides (40 CFR 170.240 (d)(4-6)), the handler PPE requirements may be reduced or 
modified as specified in the WPS. Human flagging is prohibited. 
 
IMPORTANT: When reduced PPE is worn because a closed system is being used, 
handlers must be provided all PPE specified above for “applicators and other handlers” 
and have such PPE immediately available for use in an emergency, including a spill or 
equipment breakdown. 
 
User Safety Recommendations 
 
Users should: 
 Wash hands before eating, drinking, chewing gum, using tobacco or using the toilet. 
 Remove clothing/PPE immediately if pesti cide gets inside. Then wash thoroughly 
and put on clean clothing. 
 Remove PPE immediately after handling th is product. Wash the outside of gloves 
before removing. As soon as possibl e, wash thoroughly and change into clean 
clothing. 
 
2.3 Environmental Hazards 
Azoxystrobin, benzovindiflupyr and propiconazole are toxic to fish, and azoxystrobin 
and benzovindiflupyr are toxic to aquatic invertebrates. Benzovindiflupyr is also toxic to 
mammals and propiconazole is also toxic to shrimp. Drift and runoff may be hazardous 
to aquatic organisms in water adjacent to treated area. Azoxystrobin can be persistent 
for several months or longer.

Trivapro Fungicide 
Page 6 
 
For terrestrial uses: DO NOT apply directly to water, or to areas where surface water is 
present, or to intertidal areas below the mean high-water mark. Drift and runoff may be 
hazardous to aquatic organisms in water adjacent to treated areas. DO NOT 
contaminate water when disposing of equipment washwater or rinsate. 
 
2.3.1 GROUNDWATER ADVISORY 
Azoxystrobin has degradation products which have properties and characteristics 
associated with chemicals detected in groundwater. This chemical may leach into 
groundwater if used in areas where soils are permeable, particularly where the water 
table is shallow. 
 
2.3.2 SURFACE WATER ADVISORY 
This product may impact surface water quality due to runoff of rain water. This is 
especially true for poorly draining soils and soils with shallow groundwater. A 15-foot 
vegetative buffer strip between areas to which this product is applied and surface water 
features including ponds, streams, and springs will reduce the potential loading of 
benzovindiflupyr, propiconazole and azoxystrobin from runoff water and sediment. DO 
NOT cultivate within 15 feet of the aquatic areas to allow growth of a vegetative filter 
strip. Runoff of this product will be reduced by avoiding applications when rainfall or 
irrigation is expected to occur within 48 hours. Sound erosion control practices will 
reduce this product’s potential to reach aquatic sediment via runoff. 
 
2.4 Physical or Chemical Hazards 
DO NOT use or store near heat or open flame. 
 
DIRECTIONS FOR USE 
 
It is a violation of federal law to use this product in a manner inconsistent with its 
labeling. 
 
Trivapro Fungicide must be used only in accordance with directions on this label or in 
separately published, EPA approved, Syngenta supplemental labeling for this product. 
 
DO NOT apply this product in a way that will contact workers or other persons, either 
directly or through drift. Only protected handlers may be in the area during application. 
For any requirements specific to your state or tribe, consult the agency responsible for 
pesticide regulation. 
 
Notify state and/or Federal authorities an d Syngenta immediately if you observe any 
adverse environmental effects due to use of this product. 
 
FAILURE TO FOLLOW THE USE DIRECTIONS AND PRECAUTIONS ON THIS 
LABEL MAY RESULT IN PLANT INJURY, POOR DISEASE CONTROL AND/OR 
ILLEGAL RESIDUES.

Trivapro Fungicide 
Page 7 
 
AGRICULTURAL USE REQUIREMENTS 
 
Use this product only in accordance with its labeling and with the Worker Protection 
Standard, 40 CFR part 170. This Standard contains requirements for the protection 
of agricultural workers on farms, forests, nurseries, and greenhouses, and handlers of 
agricultural pesticides. It contains requirements for training, decontamination, 
notification, and emergency assistance. It also contains specific instructions and 
exceptions pertaining to the statements on this label about personal protective 
equipment (PPE), notification to workers, and restricted-entry interval. The 
requirements in this box only apply to uses of this product that are covered by the 
Worker Protection Standard. 
 
DO NOT enter or allow worker entry into treated areas during the restricted-
entry interval (REI) of 12 hours. 
 
PPE required for early entry to treated areas that is permitted under the Worker 
Protection Standard and that involves contact with anything that has been treated, 
including plants, soil or water: 
 
 Coveralls 
 Chemical-resistant gloves: ba rrier laminate, butyl rubber ≥ 14 mils, nitrile 
rubber ≥ 14 mils, neoprene rubber ≥ 14 mils, natural rubber ≥ 14 mils, 
polyethylene, polyvinyl chloride ≥ 14 mils, or Viton® ≥ 14 mils. 
 Shoes plus socks 
 Protective eyewea r (goggles, face shield, or shielded safety glasses) 
 
3.0 PRODUCT INFORMATION 
 Read all label directions bef ore use. All applications must be made according to the 
use directions that follow. 
 Trivapro Fungicide is a broad-spectrum, pr eventative fungicide for the control of 
many important plant diseases, formulated as a suspo-emulsion (SE). 
 Trivapro Fungicide is a member of Sy ngenta’s Plant Health product line and may 
also improve the yield and/or quality of the crop. These possible benefits are due to 
positive effects on plant physiology. The effects may vary according to factors 
including the crop, crop hybrid, or environment. 
 
CROP TOLERANCE/PHYTOTOXICITY 
Crop tolerance/phytotoxicity has been found to be acceptable for all crops on the label; 
however, not all possible tank-mix combinations have been tested under all conditions. 
When possible, test your tank-mix combination(s) on a small portion of the crop to 
ensure that a phytotoxic response will not occur as a result of application. 
 
ATTENTION

Trivapro Fungicide 
Page 8 
 
Trivapro Fungicide is extremely phytotoxic to certain apple varieties. AVOID SPRAY 
DRIFT. Extreme care must be used to prevent injury to apple trees (and apple fruit). 
 
DISEASE SUPPRESSION 
If a use indicates suppression it refers to control which can range from fair to good, or 
consistent control at a level below that obtained with products registered for control. 
 
3.1 Integrated Pest (Disease) Management (IPM) 
Integrate Trivapro Fungicide into an overall disease and pest management strategy 
whenever the use of a fungicide is required. Follow cultural practices known to reduce 
disease development. This includes selection of varieties with disease tolerance, 
removal of plant debris in which inoculum overwinters, and proper timing and placement 
of irrigation. Consult your local agricultural authorities for additional IPM strategies 
established for your area. Trivapro Fungicide may be used in State Agricultural 
Extension advisory (disease forecasting) programs which advise application timing 
based on environmental factors favorable for disease development. 
 
3.2 Resistance Management 
 
For resistance management, please note that Trivapro Fungicide contains 
benzovindiflupyr, a succinate dehydrogenase inhibitor (SDHI) in Group 7; 
propiconazole, a triazole fungicide in Group 3; and azoxystrobin, a strobilurin fungicide 
in Group 11. Any fungal population may contain individuals naturally resistant to 
Trivapro Fungicide and other Group 3, 7, or 11 fungicides. A gradual or total loss of pest 
control may occur over time if these Group 3, 7, or 11 fungicides are used repeatedly in 
the same fields. Follow appropriate resistance-management strategies. 
 
To delay fungicide resistance, take one or more of the following steps: 
 
 Rotate the use of Trivapro Fungicide or other Group 3, 7, and 11 fungicides within a 
growing season sequence with different groups that control the same pathogens. 
 Use tank mixtures with fungi cides from a different group that are equally effective on 
the target pest when such use is permitted. Use at least the minimum application rate 
as labeled by the manufacturer. 
 Adopt an integrated diseas e management program for fungicide use that includes 
scouting, uses historical information related to pesticide use, and crop rotation, and 
which considers host plant resistance, impact of environmental conditions on disease 
development, disease thresholds, as well as cultural, biological and other chemical 
control practices. 
 Where possible, make use of predictive disease models to effectively time fungicide 
applications. Note that using predictive models alone is not sufficient to manage 
resistance. 
 Monitor treated fungal populati ons for resistance development. 
 Contact your local extension specialist or certified crop advisor for any additional 
pesticide resistance-management and/or IPM directions for specific crops and

Trivapro Fungicide 
Page 9 
 
pathogens. 
 For further information or to report suspected resistance contact Syngenta Crop 
Protection at 1-866-796-4368. You can also contact your pesticide distributor or 
university extension specialist to report resistance. 
 
As part of a resistance management strategy: 
 Apply no more than 2 sequent ial applications unless otherwise stated in the crop 
section. 
 When tank-mixing or alternating, use an effective partner – one that provides 
satisfactory disease control when used alone at the mixture rate. 
 Apply early to keep fungal populations low. 
 Incorporate integrated pes t management (IPM) practices into your program which 
can help reduce disease development and spread. 
 DO NOT use Trivapro Fungicide for vegetable transplant production. 
 
Follow the crop-specific resistance management directions in Section 7.0. 
 
4.0 APPLICATION DIRECTIONS 
4.1 Methods of Application 
Apply Trivapro Fungicide at rates specified in the crop tables (Section 7.0). Where 
permitted, applications can be made by ground, by air, and via chemigation as specified 
in Section 7.0. Refer to Section 4.5 for details of application by chemigation. 
 
GROUND APPLICATION: 
OBSERVE THE FOLLOWING RESTRICTIONS WHEN SPRAYING IN THE VICINITY 
OF AQUATIC AREAS INCLUDING LAKES, RESERVOIRS, RIVERS, PERMANENT 
STREAMS, MARSHES OR NATURAL PONDS, ESTUARIES, AND COMMERCIAL 
FISH PONDS. 
 DO NOT apply within 15 ft of bodies of water including lakes, reservoirs, rivers, 
permanent streams, natural ponds, marshes or estuaries. 
 Shut off the sprayer when row ends. 
 DO NOT cultivate within 15 ft of aquatic areas in order to allow growth of a 
vegetative filter strip. 
 DO NOT apply when weather conditions favor drift to aquatic areas. DO NOT 
apply when gusts or sustained winds exceed 10 mph. 
 DO NOT apply during a temperature inversion. Mist or fog may indicate the 
presence of an inversion in humid areas. 
 
4.2 Application Equipment 
Trivapro Fungicide may be applied with all types of spray equipment commonly used for 
making aerial and ground applications. Proper adjustments and calibration of spray 
equipment are needed to provide penetration and coverage essential for good disease 
control.

Trivapro Fungicide 
Page 10 
 
4.2.1 NOZZLES 
 Equip sprayers with nozzles that provide accurate and uniform application and 
desired spray quality. 
 Screens must be used to protect the pump and to prevent nozzles from clogging. 
 Nozzles must be the same size and uniformly spaced across the boom. 
 Calibrate sprayer before use. 
 
4.2.2 PUMPS 
 Use a pump with capacity to: 
1. Maintain 35-40 psi at nozzles. 
2. Provide sufficient agitation in the tank to keep tank-mixture in suspension; this 
requires recirculation of 10% of tank volume per minute. 
3. If agitation stopped for brief periods of time, re-suspend the spray solution by 
running on full agitation prior to spraying. 
 Use a jet agitator or liquid sparge tube for agitation. 
 DO NOT air sparge. 
 Screens placed on suction side of pump must be 16-mesh or coarser. 
 DO NOT place a screen in the recirculation line. 
 Use 50-mesh or coarser screens betw een the pump and boom, and where required, 
at the nozzles. 
 
For more information on spray equipment and calibration, consult sprayer 
manufacturers and state directions. For specific local directions and spray schedules, 
consult the current state agricultural directions. 
 
4.3 Application Volume and Spray Coverage 
See Crop use Directions (Section 7.0) for additional application volume information. 
 
 Thorough coverage is necessary to provide good disease control. 
 Avoid spray overlap, as crop injury may occur. 
 For aerial application, apply in a minimum of 2 gallons of water per acre unless 
specified otherwise on this label. 
 For ground application, apply in a minimum of 10 gallons of water per acre unless 
specified otherwise on this label. 
 Avoid application under conditions when uniform coverage cannot be obtained or 
when excessive spray drift may occur. 
 
4.4 Mixing Directions 
 Prepare no more spray mixture than is required for the immediate operation. 
 Thoroughly clean spray application equipment before using this product. 
 Thoroughly agitate the spray so lution before and during application. 
 Rinse spray tank thoroughly with clean wa ter after each day’s use and dispose of 
pesticide rinsate by application to an already treated area or dispose of as per state 
or local regulations.

Trivapro Fungicide 
Page 11 
 
 Restriction: DO NOT tank mix with undiluted fertilizer. Dilute the suspension 
fertilizer to 50% with water (1:1 fertilizer to water ratio) before mixing. 
 
4.4.1 TRIVAPRO FUNGICIDE ALONE 
 Add ½- ⅔ of the required amount of water to the spray or mixing tank. 
 With the agitator running, add Tr ivapro Fungicide to the tank. 
 Continue agitation while adding the remainder of the water. 
 Begin application of the spray solution after Trivapro Fungicide has completely 
dispersed into the mix water. 
 Maintain agitation until all of the mixture has been sprayed. 
 Optional Language: [Add tank-mix defoamer if needed.] 
Optional Language: [Add a tank-mix compatibility agent and buffering agents when 
using with fertilizer suspensions.] 
 
4.4.2 TANK-MIX PRECAUTIONS 
It is the pesticide user’s responsibility to ensure that all products are registered 
for the intended use. Read and follow the applicable restrictions and limitations 
and directions for use on all product labels involved in tank mixing. Users must 
follow the most restrictive directions for use and precautionary statements of 
each product in the tank mixture. 
 
 Trivapro Fungicide can be tank-mixed with ot her fungicides, herbicides, insecticides, 
liquid fertilizers, adjuvants, and additives however not all combinations or 
environmental conditions have been tested. 
 To ensure against incompatibility and crop injury, it is advised to test the 
combinations on a small portion of the crop to be treated. 
 A tank mixture with Dimet hoate may cause crop injury. 
 
4.4.3 TANK-MIX COMPATIBILITY TEST 
A jar compatibility test is advised prior to tank-mixing with other pesticides and/or 
adjuvants/additives, in order to ensure the compatibility of Trivapro Fungicide with other 
products, adjuvants or fertilizers. The advised procedure for conducting jar tank-mix 
compatibility tests is as follows: 
 
Compatibility Test: Always perform a tank-mix compatibility test when mixing with 
new or unknown tank-mix partners before use. Use compatibility agents or buffering 
agents as per manufacturer label directions when using fertilizer suspensions as carrier. 
The following test assumes a spray volume of 25 gal/A. For other spray volumes, make 
appropriate changes in the components. Perform tank-mix compatibility test as follows: 
 
1. Add 1 pt of carrier (either the water or liquid fertilizer to be used in the spray 
operation) to each of two clear 1-qt jars with tight lids. 
 
2. To one of the jars, add ¼ tsp or 1.2 ml of a commercially available tank-mix 
compatibility agent approved for this use (¼ tsp is equivalent to 2 pt/100 gallons

Trivapro Fungicide 
Page 12 
 
of spray solution). Close the lid, invert the jar, shake or stir gently to ensure 
thorough mixing of the compatibility agent. 
 
3. To both jars, add the appropriate amount of each tank-mix partner. If more than 
one tank-mix partner is to be used, follow the mixing order, add dry formulations 
(wettable powders or water dispersible granules) first, followed by liquid 
flowables, capsule suspensions, emulsifiable concentrates, and finally add 
adjuvants. After each addition, invert the jar, shake or stir gently to thoroughly 
mix. The appropriate amount of each tank-mix partner for this test, is as follows: 
 
4. Dry formulations: For each pound to be applied per acre, add 1.5 level 
teaspoons to each jar. 
 
5. Liquid formulations: For each pint to be applied per acre, add 0.5 teaspoon or 
2.5 milliliters to each jar. 
 
6. After adding all ingredients, close the jars and tighten, then invert each jar 10 
times to fully mix. Let the mixtures stand for 15-30 minutes and then assess by 
looking for separation, large flakes, precipitates, gels, heavy oily film on the jar, 
or other signs of incompatibility. Determine if a compatibility agent is needed in 
the spray mixture by comparing the two jars. If either mixture separates, but can 
be remixed readily, the mixture can be sprayed as long as good agitation is used. 
If the mixtures are incompatible, test the following methods of improving 
compatibility: (A) Pre-slurry dry formulations in water before addition to the jar, or 
(B) add the compatibility agent directly into liquid formulations, before addition to 
the jar. If these procedures are followed but incompatibility is still observed, DO 
NOT prepare the tank mix in the spray tank. 
 
4.4.4 TRIVAPRO FUNGICIDE IN TANK MIXTURES 
 Add ½- ⅔ of the required amount of water to the spray or mixing tank. 
 Start the agitator before adding any tank-mix partners 
 When using in a tank-mix, add different fo rmulation types in the sequence indicated 
below. 
1. Products packaged in water-soluble packaging 
2. Wettable powders 
3. Wettable granules (dry flowables) 
4. Liquid flowables 
5. Capsule suspensions 
6. Soluble liquids 
7. Emulsifiable concentrates 
8. Surfactants/adjuvants. 
 Allow each product to completely dissolve and disperse into the mix water before 
adding the next product. Continue agitation while the next product is added. 
 Continue agitation while adding the remainder of the water. 
 Begin application of the spray solution a fter all products have completely dispersed 
into the mix water.

Trivapro Fungicide 
Page 13 
 
 Maintain agitation until all of the mixture has been sprayed. 
 Optional Language: [Add tank-mix defoamer if needed.] 
 
4.4.5 SPRAY ADDITIVES 
 For some uses on this label, a spreadi ng/penetrating type adjuvant including a non-
ionic surfactant, crop oil concentrate, silicone based, or blend must be added at the 
manufacturer’s directed rates. 
 For other crop uses, an adjuvant is adv ised. When an adjuvant is to be used with 
this product, the use of an adjuvant that meets the standards of the Council of 
Producers and Distributors of Agrotechnology (CPDA) certification program is 
advised. 
 Under certain weather conditions (particula rly high temperatures), this fungicide in 
combination with high rates of silicone-based or oil containing (petroleum or crop) 
additives or adjuvants may cause injury. Consult a Syngenta representative for 
more information concerning additives or adjuvants. 
 
4.5 Application through Irrigation Systems (Chemigation) 
4.5.1 APPLICATION DIRECTIONS FOR OVERHEAD IRRIGATION SYSTEMS 
 Use only on crops for which chemi gation is specified on this label. 
 Use only with drive systems which pr ovide uniform water distribution. 
 DO NOT use end guns because of non-uniform application. 
 Apply this product only through center-piv ot, solid-set, hand-move, or moving-wheel 
irrigation systems. DO NOT apply this product through any other type of irrigation 
system. 
 Crop injury, lack of effectiveness, or illega l pesticide residues in the crop can result 
from non-uniform distribution of treated water. 
 If you have questions about calibration, contac t State Extension Service specialists, 
equipment manufacturers, or chemigation experts. 
 DO NOT connect an irrigation system (including greenhouse systems) used for 
pesticide application to a public water system unless the pesticide label-prescribed 
safety devices for public water systems are in place. 
 A person knowledgeable of the chemi gation system and responsible for its 
operation, or under the supervision of the responsible person, shall shut the system 
down and make necessary adjustments if the need arises. 
 Chemical tank and injector system mu st be thoroughly cleaned and flushed with 
clean water prior to use. 
 DO NOT apply when winds are greater than 10-15 mph to avoid drift or wind skips. 
 DO NOT apply when wind speed favors drift beyond the area intended for treatment. 
 Thorough coverage of foliage is required for good control. 
 Good agitation must be maintained in the tank during the entire application period. 
 Trivapro Fungicide has not been sufficient ly tested via irrigation systems to 
determine product efficacy. 
 In general, best performance via irrigation is 0.1 to 0.25 inches of water per acre.

Trivapro Fungicide 
Page 14 
 
Center-Pivot Irrigation 
Restrictions: (1) Use only with drive systems which provide uniform water distribution. 
(2) DO NOT use end guns when chemigating Trivapro Fungicide through center pivot 
systems because of non-uniform application. 
 
 Determine the size of the area to be treated. 
 Determine the time required to apply ⅛-½ inch of water over the area to be treated 
when the system and injection equipment are operated at normal pressures as 
specified by the equipment manufacturer. When applying Trivapro Fungicide 
through irrigation equipment use the lowest obtainable water volume while 
maintaining uniform distribution. Run the system at 80-95% of the manufacturer’s 
rated capacity. 
 Using water, determine the injecti on pump output when operated at normal line 
pressure. 
 Determine the amount of Trivapro Fungicide required to treat the area covered by 
the irrigation system. 
 Add the required amount of Trivapro Fungicide and sufficient water to meet the 
injection time requirements to the solution tank. 
 Make sure the system is fully charged wit h water before starting injection of the 
Trivapro Fungicide solution. Time the injection to last at least as long as it takes to 
bring the system to full pressure. 
 Maintain constant solution tank agitation during the injection period. 
 Continue to operate the system until the Trivapro Fungicide solution has cleared the 
sprinkler head. 
 
Solid-Set, Hand-Move, and Moving-Wheel Irrigation 
 Determine the acreage covered by the sprinklers. 
 Fill injector solution tank with water and adj ust flow rate to use the contents over a 
20 to 30-minute interval. When applying Trivapro Fungicide through irrigation 
equipment use the lowest obtainable water volume while maintaining uniform 
distribution. 
 Determine the amount of Trivapro Fungi cide required needed to treat the area 
covered by the irrigation system. 
 Add the required amount of Trivapro Fungicide into the same quantity of water used 
to calibrate the injection period. 
 Operate the system at the same pressure and time interval established during the 
calibration. 
 Stop injection equipment afte r treatment is completed. Continue to operate the 
system until the Trivapro Fungicide solution has cleared the last sprinkler head. 
 
4.5.2 OPERATING INSTRUCTIONS FOR CHEMIGATION 
1. The system must contain a functional ch eck valve, vacuum relief valve, and low 
pressure drain appropriately located on the irrigation pipeline to prevent water-
source contamination from backflow. 
2. The pesticide injection pipeline must contain a functional, automatic, quick-
closing check valve to prevent the flow of fluid back toward the injection pump.

Trivapro Fungicide 
Page 15 
 
3. The pesticide injection pipeline must al so contain a functional, normally closed, 
solenoid-operated valve located on the intake side of the injection pump and 
connected to the system interlock to prevent fluid from being withdrawn from the 
supply tank when the irrigation system is either automatically or manually shut 
down. 
4. The system must contain functional interl ocking controls to automatically shut off 
the pesticide injection pump when the water pump motor stops. 
5. The irrigation line or water pump must include a functional pressure switch which 
will stop the water pump motor when the water pressure decreases to the point 
where pesticide distribution is adversely affected. 
6. Systems must use a metering pump, for example a positive displacement 
injection pump (e.g., diaphragm pump) effectively designed and constructed of 
materials that are compatible with pesticides and capable of being fitted with a 
system interlock. 
7. DO NOT apply when wind speed favors drift beyond the area intended for 
treatment. 
 
Allow sufficient time for pesticide to be flushed through all lines and all nozzles 
before turning off irrigation water. 
 
4.5.3 SPECIFIC INSTRUCTIONS FOR PUBLIC WATER SYSTEMS 
1. Public water system means a system for the provision to the public of piped water 
for human consumption if such system has at least 15 service connections or 
regularly serves an average of at least 25 individuals daily at least 60 days out of 
the year. 
2. Chemigation systems connect ed to public water systems must contain a functional, 
reduced-pressure zone (RPZ), back-flow preventer or the functional equivalent in 
the water supply line upstream from the point of pesticide introduction. As an 
option to the RPZ, the water from the public water system must be discharged into 
a reservoir tank prior to pesticide introduction. There shall be a complete physical 
break (air gap) between the outlet end of the fill pipe and the top or overflow rim of 
the reservoir tank of at least twice the inside diameter of the fill pipe. 
3. The pesticide injection pipeline must c ontain a functional, automatic, quick-closing 
check valve to prevent the flow of fluid back toward the injection pump. 
4. The pesticide injection pipeline must contain a functional, normally closed, 
solenoid-operated valve located on the intake side of the injection pump and 
connected to the system interlock to prevent fluid from being withdrawn from the 
supply tank when the irrigation system is either automatically or manually shut 
down. 
5. The system must contain functional interl ocking controls to automatically shut off 
the pesticide injection pump when the water pump motor stops, or in cases where 
there is no water pump, when the water pressure decreases to the point where 
pesticide distribution is adversely affected. 
6. Systems must use a metering pump, for ex ample a positive displacement injection 
pump (e.g., diaphragm pump) effectively designed and constructed of materials

Trivapro Fungicide 
Page 16 
 
that are compatible with pesticides and capable of being fitted with a system 
interlock. 
7. DO NOT apply when wind speed favors drift beyond the area intended for 
treatment. 
 
5.0 ROTATIONAL CROP RESTRICTIONS 
The following crops may be planted at the specified interval following application of 
Trivapro Fungicide: 
 
Crop Plant-Back Interval 
Bulb vegetables 
Canola 
Cereals (wheat, barley, triticale, rye, oat) 
Corn 
Corn, sweet 
Beans, dry and succulent 
Ginseng 
Grasses grown for seed (bluegrass, 
bromegrass, fescue, orchardgrass, and 
ryegrass only) 
Peanuts 
Soybean 
Sugar Beet 
Sugarcane 
0 days 
Blueberry, lowbush 
Cotton 
Cucurbits vegetables 
Fruiting vegetables 
Potatoes 
Tomatoes 
Tuberous & corm Crop Subgroup 1C 
105 days 
All other crops Intended for Food and Feed 105 days 
 
6.0 RESTRICTIONS AND PRECAUTIONS 
6.1 Use Restrictions 
 DO NOT apply through any ultra-low volume (ULV) spray system. 
 Not for use in greenhouses. 
 DO NOT use spray equipment which has been previously used to apply Trivapro 
Fungicide to spray apple trees. Even trace amounts can cause unacceptable 
phytotoxicity to certain apple and crabapple varieties. 
 Aerial application is prohibited in New York State. 
 To help manage fungicide resistance, DO NOT use Trivapro Fungicide for 
commercial transplant production.

Trivapro Fungicide 
Page 17 
 
 
6.1.1 Aerial Spray RESTRICTIONS 
Observe the following restrictions when spraying in the vicinity of aquatic areas 
including lakes, reservoirs, rivers, permanent streams, marshes or natural ponds, 
estuaries and commercial fish ponds. 
 DO NOT apply by air within 150 ft of lakes, reservoirs, rivers, permanent 
streams, marshes or natural ponds, estuaries and commercial fish ponds. 
 Risk of exposure to aquatic areas can be reduced by avoiding applications when 
wind direction is toward the aquatic area. 
 Low humidity and high temperatures in crease the evaporation rate of spray 
droplets and therefore the likelihood of increased spray drift to aquatic area. 
Avoid spraying during conditions of low humidity and/or high temperatures. 
 
 
6.2 Use Precautions 
 Under certain conditions conducive to extended infection periods, use another 
registered fungicide for additional applications if maximum amount of Trivapro 
Fungicide has been used. 
 If isolates resistant to Group 7, 3 or 11 fungicides are present, efficacy can be 
reduced for certain diseases. 
 The higher rates in the rate range and/or shorter spray intervals may be required 
under conditions of heavy infection pressure, with highly susceptible varieties, or 
when environmental conditions are conducive to disease. 
 
 
6.3 Spray Drift Management 
 
SPRAY DRIFT MANAGEMENT 
 
Aerial Applications 
 
 DO NOT release spray at a height greater than 10 ft. above the crop canopy, unless 
a greater application height is necessary for pilot safety. 
 Applicators are required to select nozzles that deliver medium to coarse spray 
droplets in accordance with ASABE Standard S-572.1. 
 DO NOT apply when wind speeds exceed 15 mph at the application site. If the 
windspeed is greater than 10 mph, the boom length must be 65% or less of the 
wingspan for fixed wing aircraft and 75% or less of the rotor diameter for helicopters. 
Otherwise, the boom length must be 75% or less of the wingspan for fixed-wing 
aircraft and 90% or less of the rotor diameter for helicopters. 
 Applicators must use ½ swath displace ment upwind at the downwind edge of the 
field. 
 DO NOT apply during temperature inversions.

Trivapro Fungicide 
Page 18 
 
Ground Boom Applications 
 
 User must only apply with the release height directed by the manufacturer, but no 
more than 4 feet above the ground or crop canopy. 
 Applicators are required to use a medium or coarser droplet size (ASABE S-572.1). 
 DO NOT apply when wind speeds exceed 15 miles per hour at the application site. 
 DO NOT apply during temperature inversions. 
 
 
6.3.1 CONTROLLING DROPLET SIZE - GROUNDBOOM 
 Volume – Increasing the spray volume so that larger droplets are produced will 
reduce spray drift. Use the highest practical spray volume for the application. If a 
greater spray volume is needed, consider using a nozzle with higher flow rate. 
 Pressure – Use the lowest spray pressure directed for the nozzle to produce the 
target spray volume and droplet size. DO NOT exceed the nozzle manufacturer’s 
directed pressures. For many nozzle types, lower pressure produces larger 
droplets. When higher flow rates are needed, use higher rate nozzles instead of 
increasing pressure. 
 Number of Nozzles – Use the minimum number of nozzles that provide uniform 
coverage. 
 Nozzle Type - Use a spray nozzle that is designed for the intended application. 
Consider using nozzles designed to reduce drift.

Trivapro Fungicide 
Page 19 
 
 
6.3.2 Controlling Droplet Size – Aircraft 
 Adjust Nozzles - Follow nozzle manufactu rers directions for setting up nozzles. 
Generally, to reduce fine droplets, nozzles must be oriented parallel with the airflow 
in flight. 
 
6.3.3 APPLICATION HEIGHT 
 Applications must be made at the lowest height above the target area that still 
provides uniform coverage of the target. Making applications at the lowest yet 
effective height reduces exposure of droplets to wind. 
 
6.3.4 BOOM HEIGHT – Groundboom 
 For ground equipment, the boom must remain level with the crop and have minimal 
bounce. 
 
6.3.5 RELEASE HEIGHT – Aircraft 
 
 Higher release heights increase the potential for spray drift. 
 
6.3.6 SHIELDED SPRAYERS 
 Shielding the boom or indi vidual nozzles can reduce spray drift. Consider using 
shielded sprayers. Verify that the shields are not interfering with the uniform 
deposition of the spray on the target area. 
 
 
6.3.7 WIND 
 Drift potential is lowest when wind speeds are 10 mph or less. However, many 
factors, including droplet size, pressure, and equipment type determine drift potential 
at any given wind speed. Note: Local terrain can influence wind patterns. 
 Drift potential increases with wind speeds. AVOID APPLICATIONS DURING 
GUSTY WIND CONDITIONS. 
 Applicators need to be familiar with local wi nd patterns and terrain that could affect 
spray drift. 
 
6.3.8 TEMPERATURE AND HUMIDITY 
 When making applications in hot and dr y conditions, set up equipment to produce 
larger droplets to reduce effects of evaporation. 
 
6.3.9 TEMPERATURE INVERSIONS 
 Applications must not occur during a temperature inversion because these 
conditions increase the potential for drift. Temperature inversions restrict vertical air 
mixing, which causes small-suspended droplets to remain in a concentrated cloud. 
This cloud can move in unpredictable directions due to light variable winds common 
during inversions. Temperature inversions are characterized by increasing

Trivapro Fungicide 
Page 20 
 
temperatures with altitude and are common on nights with limited cloud cover and 
light to no wind. They begin to form as the sun sets and often continue into the 
morning. Ground fog is a good indicator that a thermal inversion is occurring. If 
ground fog is not present smoke from an aircraft smoke generator or other source 
can be used to indicate the presence of a thermal inversion. Smoke that layers and 
moves laterally in a concentrated cloud (under low wind conditions) indicates an 
inversion, while smoke that moves upward and rapidly dissipates, indicates good 
vertical air mixing. 
 
6.3.10 NON-TARGET AREAS 
 DO NOT apply this pesticide when the product may drift to non-target areas (i.e., 
residential areas, bodies of water, known habitat for threatened or endangered 
species, non-target crops).

Trivapro Fungicide 
Page 21 
 
7.0 CROP USE DIRECTIONS 
7.1 Bulb Vegetable Group 3-07; Dry Bulb Group 3-07A; Onions, green 
Group 3-07B 
Crops (including all cultivars, varieties, and/or hybrids of these) [Not for use in California] 
Dry Bulb Group 3-07A: 
Daylily, bulb 
Fritillaria, bulb 
Garlic, bulb 
Garlic, great-headed 
Garlic, serpent, bulb 
Lily, bulb 
Onion, bulb 
Onion, Chinese, bulb 
Onion, pearl 
Potato, bulb 
Shallot, bulb 
Green Onion Group 3-07B: 
Chive, Chinese fresh leaves 
Chive, fresh leaves 
Elegans hosta 
Fritillaria, leaves 
Kurrat 
Lady’s leek 
Leek 
Leek, wild 
Onion, Beltsville bunching 
Onion, fresh 
Onion, green 
Onion, marcostem 
Onion, tree, tops 
Onion, Welsh, tops 
Shallot, fresh leaves 
Target Disease 
Rate 
(fl oz/A) Application Timing Use Directions 
Cladosporium leaf 
blotch 
(C. allii) 
Powdery Mildew 
(Leveillula taurica) 
Purple Blotch 
(Alternaria porri) 
Rust 
(Puccinia allii) 
Stemphyllium leaf 
blight and stalk rot 
(S. vesicarium) 
 
10.7 – 
27.7 
Apply prior to disease 
development. 
 
Continue applications 
through season on a 7 to 14-
day interval, following the 
resistance management 
guidelines. 
 
No more than two 
applications of Trivapro 
Fungicide may be applied on 
a 7-day interval. 
Apply by ground, air, or chemigation. 
 
An adjuvant may be added at 
directed rates. 
 
[Optional language if label has a rate 
range: If disease pressure is high, 
use the highest specified rate. 
 
Optional language if label has a 
single rate and interval range: If 
disease pressure is high, use the 
shortest interval. 
 
Optional language if label has a rate 
range and interval range: If disease 
pressure is high, use the shortest 
interval and highest specified rate.] 
Resistance Management: 
 DO NOT make more than two applications of Trivapro Fungicide or other Group 7 or 11 fungicides 
before alternation with a fungicide that is not in Group 7 or 11. 
USE RESTRICTIONS 
1) Refer to Section 6.1 for additional product use restrictions. 
2) Maximum Single Application Rate: 27.7 fl oz/A 
3) Minimum Application Interval: 7 days 
4) Maximum Annual Rate: 55.4 fl oz product/A/year 
a. DO NOT apply more than 0.45 lb ai/A/year of propiconazole-containing products. 
b. DO NOT apply more than 1.5 lb ai/A/year of azoxystrobin-containing products. 
c. DO NOT apply more than 0.272 lb ai/A/year of benzovindiflupyr-containing products. 
5) DO NOT exceed 4 applications per year. 
6) Pre-harvest Interval (PHI): 
a. Green Onion Group 3-07B: 7 days 
b. Dry Bulb Group 3-07A: 14 days 
7) Aerial application is prohibited in New York State.

Trivapro Fungicide 
Page 22 
 
7.2 Rapeseed (Canola) Subgroup 20A 
Crops (including all cultivars, varieties, and/or hybrids of these) [Not for use in California] 
Borage 
Crambe 
Cuphea 
Echium 
Flax seed 
Gold of pleasure 
Hare’s ear mustard 
Lesquerella 
Lunaria 
Meadowfoam 
Milkweed 
Mustard seed 
Oil radish 
Poppy seed 
Rapeseed 
Sesame 
Sweet rocket 
Target Disease 
Rate 
(fl oz/A) Application Timing Use Directions 
Alternaria black spot 
(Alternaria.brassicae) 
Black leg/Phoma 
(Leptosphaeria 
maculans) 
Cercospora leafspot 
(C. brassicicola) 
Leaf spot and pod rot 
(Alternaria alternata) 
Powdery mildew 
(Erysiphe polygoni) 
 
13.7 For Phoma control, 
apply during the 
rosette stage between 
2nd true leaf and 
bolting. 
 
For Alternaria, make 
an application at the 
end of flowering/early 
pod set. 
 
For other foliar 
diseases, apply at first 
sign of disease. 
Apply by ground, air, or 
chemigation. 
 
An adjuvant may be added at 
directed rates. 
 
 
USE RESTRICTIONS 
1) Refer to Section 6.1 for additional product use restrictions. 
2) Maximum Single Application Rate: 13.7 fl oz/A 
3) Make no more than one Trivapro Fungicide application per year. 
4) Maximum Annual Rate: 13.7 fl oz product/A/year 
a. DO NOT apply more than 0.113 lb ai/A/year of propiconazole-containing products. 
b. DO NOT apply more than 0.45 lb ai/A/year of azoxystrobin-containing products. 
c. DO NOT apply more than 0.046 lb ai/A/year of benzovindiflupyr-containing products. 
5) Pre-harvest Interval (PHI): 30 days 
6) Aerial application is prohibited in New York State.

Trivapro Fungicide 
Page 23 
 
7.3 Cereals 
Crops (including all cultivars, varieties, and/or hybrids of these) 
Barley 
Oats 
Rye 
Triticale 
Wheat 
Target Disease 
Rate 
(fl oz/A) Application Timing Use Directions 
Early-season 
suppression of: 
Glume blotch 
(Stagonospora 
nodorum) 
Leaf blight 
(Septoria tritici) 
Powdery mildew 
(Blumeria spp.) 
Rusts 
(Puccinia spp.) 
Tan spot 
(Pyrenophora tritici-
repentis) 
9.4 – 13.7 
 
Apply prior to disease 
development for disease 
control and plant health 
benefits. 
 
Apply 9.4 fl oz/A after first 
tiller visible to 2-6 node 
stage (Feekes 2-7, 
Zadoks 21-36) for 
suppression of early 
season diseases. 
 
Make applications no 
closer than 14 days apart. 
Apply by ground, air, or 
chemigation. 
 
An adjuvant may be added 
at directed use rates. 
 
 
Control of Leaf 
Diseases: 
Alternaria leaf blight[*] 
 (Alternaria triticina) 
Barley scald[*] 
 (Rhynchosporium 
 secalis) 
Black point[*] 
 (C. sativus, Alternaria 
 spp.) 
Ergot[*] 
 (Claviceps purpurea) 
Glume blotch 
(Stagonospora 
nodorum) 
Helminthosporium leaf 
blight 
(Helminthosporium spp.) 
Leaf blight 
(Septoria tritici) 
Powdery mildew 
(Blumeria spp., Erysiphe 
spp.) 
Ramularia leaf spot 
 (Ramularia collo-
cygni)[*] 
Rusts 
(Puccinia spp.) 
Spot blotch 
(Bipolaris sorokiniana) 
Tan spot 
(Pyrenophora tritici-
repentis) 
9.4 – 13.7 
 
For disease control on the 
flag leaf, apply from 
Feekes 8 (Zadoks 37) 
through Feekes 10 
(Zadoks 45). 
 
Protecting the flag leaf is 
important for maximizing 
the potential yield and 
plant health benefits. 
Highest yields are 
normally obtained if 
Trivapro Fungicide is 
applied when the flag leaf 
is 50% to fully emerged. 
 
Applications may be 
made no closer than a 
14-day interval. Trivapro 
Fungicide can be applied 
through full head 
emergence (Feekes 
growth stage 10.5.4). DO 
NOT apply after this 
stage to avoid possibly 
illegal residues. 
An adjuvant may be added 
at directed use rates.

Trivapro Fungicide 
Page 24 
 
[*Not for use in California.] 
Feekes Growth Stage and Zadoks description: Feekes 8 (Zadoks 37) – flag leaf just visible; Feekes 
10 (Zadoks 45) – swollen boot; Feekes 10.3 (Zadoks 55) – 50% of ear has emerged; Feekes 10.51 
(Zadoks 61) – beginning anthesis; Feekes 10.52 (Zadoks 65) – mid-flowering (mid-anthesis) 
Resistance Management: 
 DO NOT make more than two applications of Trivapro Fungicide or other Group 7 or 11 fungicides 
before alternation with a fungicide that is not in Group 7 or 11. 
USE RESTRICTIONS 
1) Refer to Section 6.1 for additional product use restrictions. 
2) Maximum Single Application Rate: 13.7 fl oz/A 
3) Minimum Application Interval: 14 days 
4) Maximum Annual Rate for forage and hay: 13.7 fl oz/A 
5) Maximum Annual Rate (except forage and hay): 27.4 fl oz/A/year 
a. DO NOT apply more than 0.22 lb ai/A/year of propiconazole-containing products. 
b. DO NOT apply more than 0.4 lb ai/A/year of azoxystrobin-containing products. 
c. DO NOT apply more than 0.092 lb ai/A/year of benzovindiflupyr-containing products. 
6) DO NOT exceed 2 applications per year. 
7) DO NOT apply after Feekes growth stage 10.5.4 
8) Pre-harvest Interval (PHI): 
a. Forage and Hay: 7 days 
9) Aerial application is prohibited in New York State.

Trivapro Fungicide 
Page 25 
 
7.4 Corn (except sweet) 
Crops (including all cultivars, varieties, and/or hybrids of these except sweet corn) – See 
Section 7.5 for sweet corn use directions. 
Corn, field Popcorn 
Target Disease 
Rate 
(fl oz/A) Application Timing Use Directions 
Anthracnose leaf blight 
(Colletotrichum 
graminicola) 
Curvularia leaf spot[*] 
(Curvularia lunata) 
Eye spot 
(Aureobasidium zeae) 
Gray leaf spot 
(Cercospora zeae-
maydis) 
Northern corn leaf blight 
(Setosphaeria turcica) 
Northern corn leaf spot 
(Cochliobolus 
carbonum) 
Physoderma brown spot 
(Physoderma maydis) 
Rusts 
(Puccinia spp.) 
Southern corn leaf blight 
(Cochliobolus 
heterostrophus) 
also known as 
Helminthosporium leaf 
blights 
(H. maydis, H. turcicum, 
H. carbonum) 
Tar spot[*] 
(Phyllachora maydis) 
 
Suppression of: 
Diplodia ear rot 
(D. maydis) 
13.7 
 
An early application (V4-V8) 
may be applied for early-
season disease control and 
plant health benefits. 
 
Continue applications 
through season on a 14-day 
interval, following the 
resistance management 
guidelines. 
 
Later-season 
applications: Apply late 
vegetative (V8 to VT) or at 
VT to R1 for disease control 
and plant health benefits. 
The R1 timing is advised for 
best results. 
 
If conditions favorable for 
disease persist, apply again 
14 days later. 
Apply by ground, air, or 
chemigation. 
 
An adjuvant may be added 
at directed use rates. 
 
Avoid the use of adjuvants 
or other additives containing 
adjuvants after the V8 
growth stage and prior to 
the VT growth stage, as use 
during these development 
times may impose stress on 
the plant that could inhibit 
proper kernel development. 
VT is defined as when the 
last branch of the tassel is 
completely visible, but silks 
have not yet emerged from 
the ear shoot. 
 
If an adjuvant or other 
additive is included and 
applied between the V8 and 
VT growth stages, the 
grower and user are 
responsible for contacting 
the adjuvant/additive source 
(distributor, retailer, or 
manufacturer) to confirm 
that adjuvant/additive has 
been tested and proven to 
be safe to apply at those 
growth stages. 
[*Not for use in California.] 
Growth Stage Description: V4-V8 – 4-8 leaves with visible leaf collars have emerged; VT – begin 
tasseling; R1 –silk emergence 
Resistance Management: 
 DO NOT make more than two applications of Trivapro Fungicide or other Group 7 or 11 fungicides 
before alternation with a fungicide that is not in Group 7 or 11. 
Precaution: 
 Mixing with Herbicides: If mixing with herbicides other than solo glyphosate products, Acuron®, 
Callisto® or Callisto Xtra, Lexar®, Lumax®, consult your local Syngenta representative. 
USE RESTRICTIONS 
1) Refer to Section 6.1 for additional product use restrictions. 
2) Maximum Single Application Rate: 13.7 fl oz/A

Trivapro Fungicide 
Page 26 
 
3) Minimum Application Interval: 14 days 
4) Maximum Annual Rate: 41.1 fl oz/A/year 
a. DO NOT apply more than 0.45 lb ai/A/year of propiconazole-containing products. 
b. DO NOT apply more than 2.0 lb ai/A/year of azoxystrobin-containing products. 
c. DO NOT apply more than 0.092 lb ai/A/year of benzovindiflupyr-containing products. 
5) DO NOT exceed 3 applications per year. 
6) Pre-harvest Interval (PHI): Forage, Grain, and Stover: 30 days. 
7) Aerial application is prohibited in New York State.

Trivapro Fungicide 
Page 27 
 
7.5 Corn, Sweet 
Crops (including all cultivars, varieties, and/or hybrids) 
Sweet corn 
Target Disease 
Rate 
(fl oz/A) Application Timing Use Directions 
Anthracnose leaf blight 
(Colletotrichum 
graminicola) 
Curvularia leaf spot[*] 
(Curvularia lunata) 
Eye spot 
(Aureobasidium zeae) 
Gray leaf spot 
(Cercospora zeae-
maydis) 
Northern corn leaf blight 
(Setosphaeria turcica) 
Northern corn leaf spot 
(Cochliobolus carbonum) 
Physoderma brown spot 
(P. maydis) 
Rusts 
(Puccinia spp.) 
Southern corn leaf blight 
(Cochliobolus 
heterostrophus) 
Tar Spot[*] 
(Phyllachora maydis) 
Yellow leaf blight 
(Phyllosticta maydis) 
13.7 Begin applications prior to 
disease development. 
 
Continue applications 
through season on a 14-day 
interval, following the 
resistance management 
guidelines. 
Apply by ground, air, or 
chemigation. 
 
An adjuvant may be added 
at directed use rates. 
[*Not for use in California.] 
Resistance Management: 
 DO NOT make more than two applications of Trivapro Fungicide or other Group 7 or 11 fungicides 
before alternation with a fungicide that is not in Group 7 or 11. 
USE RESTRICTIONS 
1) Refer to Section 6.1 for additional product use restrictions. 
2) Maximum Single Application Rate: 13.7 fl oz/A 
3) Minimum Application Interval: 14 days 
4) Maximum Annual Rate: 54.8 fl oz/A/year 
a. DO NOT apply more than 0.45 lb ai/A/year of propiconazole-containing products. 
b. DO NOT apply more than 2.0 lb ai/A/year of azoxystrobin-containing products. 
c. DO NOT apply more than 0.136 lb ai/A/year of benzovindiflupyr-containing products. 
5) DO NOT exceed 4 applications per year. 
6) Pre-harvest Interval (PHI): Ears and Forage: 14 days 
7) Aerial application is prohibited in New York State.

Trivapro Fungicide 
Page 28 
 
7.6 Beans, Dry and Succulent (except soybean) 
Crops (Including all cultivars, varieties and/or hybrids of these) [Not for use in California] 
Dried cultivars of bean (Lupinus 
spp.) 
(grain lupin, sweet lupin, white 
lupin, and white sweet lupin) 
Bean (Phaseolus spp.) 
(field bean, kidney bean, lima 
bean (dry), navy bean, pinto 
bean, tepary bean) 
Bean (Vigna spp.) 
(adzuki bean, black-eyed pea, 
catjang, cowpea, Crowder pea, 
moth bean, mung bean, rice bean, 
southern pea, urd bean) 
Broad bean (dry) 
 
Chickpea 
 
Target Disease 
Rate 
(fl oz/A) Application Timing Use Directions 
Alternaria blight 
Alternaria leaf spot 
(A. alternata) 
Ascochyta blight, leaf spot 
(Ascochyta spp.) 
Powdery mildew 
(Leveillula taurica) 
Anthracnose 
(Colletotrichum spp.) 
Cercospora leaf spot 
(Cercospora spp.) 
Mycosphaerella blight 
(Mycosphaerella spp.) 
Rust 
(Uromyces 
appendiculatus, 
Phakopsora spp.) 
Web Blight 
(Rhizoctonia solani) 
13.7 Begin applications prior to 
disease development. 
 
Continue applications through 
season on a 14-day interval, 
following the resistance 
management guidelines. 
Apply by ground, air, or 
chemigation. 
 
An adjuvant may be 
added at directed use 
rates. 
Resistance Management: 
 DO NOT make more than two applications of Trivapro Fungicide or other Group 7 or 11 fungicides 
before alternation with a fungicide that is not in Group 7 or 11. 
USE RESTRICTIONS 
1) Refer to Section 6.1 for additional product use restrictions. 
2) Maximum Single Application Rate: 13.7 fl oz/A 
3) Minimum Application Interval: 14 days 
4) Maximum Annual Rate: 41.1 fl oz/A/year 
a. DO NOT apply more than 0.34 lb ai/A/year of propiconazole-containing products. 
b. DO NOT apply more than 1.5 lb ai/A/year of azoxystrobin-containing products. 
c. DO NOT apply more than 0.112 lb ai/A/year of benzovindiflupyr-containing products. 
5) DO NOT exceed 3 applications per year. 
6) DO NOT use on cowpea cultivars intended for livestock feeding only. 
7) Pre-harvest Interval (PHI): 14 days 
8) Aerial application is prohibited in New York State.

Trivapro Fungicide 
Page 29 
 
7.7 Grasses Grown for Seed 
 
Crops (including all cultivars and/or varieties of these) [Not for use in California] 
Bluegrass 
Bromegrass 
Fescue 
Orchardgrass 
Ryegrass 
Target Disease 
Rate 
(fl oz/A) Application Timing Use Directions 
Ergot Stem Diseases 
Powdery Mildew 
(Erysiphe graminis) 
Rusts 
(Puccinia spp.) 
Selenophoma Stem 
Eyespot 
(Selenophoma spp.) 
13.7 – 27.4 Begin applications prior to 
disease development and 
continue throughout the 
season on a 14-28 day 
schedule. 
 
 
Apply by ground, air, or 
chemigation. 
 
The addition of a 
spreading/penetrating type 
adjuvant including organo-silicon 
blends with either non-ionic 
surfactants (NIS) or vegetable 
based crop oils (COC); or 
vegetable based COC (not 
mineral); or NIS with at least 
90% concentration is advised. 
 
[Optional language if label has a 
rate range: If disease pressure 
is high, use the highest specified 
rate. 
 
Optional language if label has a 
single rate and interval range: If 
disease pressure is high, use the 
shortest interval. 
 
Optional language if label has a 
rate range and interval range: If 
disease pressure is high, use the 
shortest interval and highest 
specified rate.] 
Resistance Management: 
 DO NOT make more than two applications of Trivapro Fungicide or other Group 7 or 11 fungicides 
before alternation with a fungicide that is not in Group 7 or 11. 
USE RESTRICTIONS 
1) Refer to Section 6.1 for additional product use restrictions. 
2) Maximum Single Application Rate: 27.4 fl oz/A 
3) Minimum Application Interval: 14 days 
4) Maximum Annual Rate: 54.8 fl oz/A/year 
a. DO NOT apply more than 0.9 lb ai/A/year of propiconazole-containing products. 
b. DO NOT apply more than 0.8 lb ai/A/year of azoxystrobin-containing products. 
c. DO NOT apply more than 0.11 lb ai/A/year of benzovindiflupyr-containing products. 
5) DO NOT exceed 2 applications per year. 
6) Only for use on the following cool season grasse s: bluegrass, bromegrass, fescue, orchardgrass, 
and ryegrass. 
7) Aerial application is prohibited in New York State. 
8) DO NOT apply to Bermuda grass grown for seed.

Trivapro Fungicide 
Page 30 
 
9) DO NOT feed hay cut within 20 days of last application. 
10) DO NOT graze treated areas within 140 days of the last application. 
11) Pre-harvest Interval (PHI): 20 days

Trivapro Fungicide 
Page 31 
 
 
7.8 Peanut 
Crops (including all cultivars, varieties, and/or hybrids) [Not for use in California] 
Peanut 
Target Disease 
Rate 
(fl oz/A) Application Timing Use Directions 
Early leaf spot 
(Cercospora 
arachidicola) 
Late leaf spot 
(Cercosporidium 
personatum) 
Pepper Spot 
(Leptosphaerulina 
crassiasca) 
Rust 
(Puccinia arachidis) 
Web blotch 
(Phoma arachidicola) 
13.7 Begin applications prior to 
disease development. 
 
Begin foliar applications 30-
40 days after planting or at 
the first appearance of 
disease. 
 
Continue applications on a 
21-day schedule. 
 
Check with local 
extension/forecasting 
systems to determine if an 
extended interval up to 21 
days is suitable for your 
area. 
 
For control of Southern 
stem rot and limb rot, 
broadcast Trivapro 
Fungicide at 13.7 oz/A 3 
times on a 14-day interval 
starting as early as 45-60 
days after planting or when 
conditions are conducive for 
disease. This will provide 
leafspot control as well. 
 
Optional language: An early 
(14-21 days after planting) 
application broadcast or in a 
7-10 inch band over the row 
can be used for early 
season infections. 
Apply by ground, air, or 
chemigation. 
 
An adjuvant may be added 
at directed use rates. 
 
Rhizoctonia limb rot 
(Rhizoctonia solani) 
Southern stem rot 
(Sclerotium rolfsii) 
Begin broadcast 
applications starting as early 
as 21-45 days after planting 
or when conditions are 
conducive for disease. 
 
Make 2 additional 
applications on a 14-day 
interval. This will provide 
leaf spot control as well. 
Resistance Management:

Trivapro Fungicide 
Page 32 
 
 DO NOT make more than two applications of Trivapro Fungicide or other Group 7 or 11 fungicides 
before alternation with a fungicide that is not in Group 7 or 11. 
USE RESTRICTIONS 
1) Refer to Section 6.1 for additional product use restrictions. 
2) Maximum Single Application Rate: 13.7 fl oz/A 
3) Minimum Application Interval: 14 days 
4) Maximum Annual Rate: 54.8 fl oz/A/year 
a. DO NOT apply more than 0.45 lb ai/A/year of propiconazole-containing products. 
b. DO NOT apply more than 0.8 lb ai/A/year of azoxystrobin-containing products. 
c. DO NOT apply more than 0.204 lb ai/A/year of benzovindiflupyr-containing products. 
5) DO NOT exceed 4 applications per year. 
6) Pre-harvest Interval (PHI): 30 days 
7) Aerial application is prohibited in New York State.

Trivapro Fungicide 
Page 33 
 
7.9 Soybean 
Crops (including all cultivars, varieties, and/or hybrids) 
Forage 
Hay 
Hulls Seed 
Target Disease 
Rate 
(fl oz/A) Application Timing Use Directions 
Aerial web blight 
(Rhizoctonia solani) 
Alternaria leaf spot 
(Alternaria spp.) 
Anthracnose 
(Colletotrichum 
truncatum) 
Brown spot 
(Septoria glycines) 
Cercospora blight and leaf 
spot 
(C. kikuchii) 
Frogeye leaf spot 
(Cercospora sojina) 
Pod and stem blight 
(Diaporthe phaseolorum) 
Powdery mildew 
(Microsphaera diffusa) 
Target spot 
(Corynespora cassiicola) 
13.7 – 20.7 For best results, apply at 
growth stage R3 (early pod 
set) when pods are 1/8-1/4 
inch long) for disease 
control and plant health 
benefits. 
 
Continue applications 
through season on a 14-day 
interval, following the 
resistance management 
guidelines. 
 
Apply by ground, air, or 
chemigation. 
 
An adjuvant may be added 
at directed use rates. 
Soybean rust 
(Phakopsora pachyrhizi) 
 
13.7 – 20.7 
 
Preventative control is best, 
so sprays may need to 
begin at R1. Apply at first 
indication that disease is in 
the area. Repeat on a 14- 
to 21-day interval. 
 
Scouting for the disease 
and/or being aware of the 
proximity of the disease via 
monitoring systems will aid 
in the proper timing to 
maximize the effectiveness 
of the fungicide applications. 
Apply by ground, air, or 
chemigation. 
 
An adjuvant may be added 
at directed use rates. 
 
Use higher specified rate 
and shorter specified 
interval when diseases are 
present in the field and 
incidence is less than 2% (2 
plants in 100 are infected). 
Resistance Management: 
 DO NOT make more than two applications of Trivapro Fungicide or other Group 7 or 11 fungicides 
before alternation with a fungicide that is not in Group 7 or 11. 
Precautions: 
 On certain varieties, Trivapro Fungicide applicat ions may cause crinkled, smaller and/or greener 
leaves. Yields of beans displaying these characteristics have not been reduced due to Trivapro 
Fungicide treatments. 
 If incidence of soybean rust is greater than 2% or the disease is in mid-canopy, control will not be 
acceptable. 
USE RESTRICTIONS 
1) Refer to Section 6.1 for additional product use restrictions. 
2) Maximum Single Application Rate:

Trivapro Fungicide 
Page 34 
 
a. For grain: 20.7 fl oz/A 
b. For forage and hay: 13.7 fl oz/A 
3) Minimum Application Interval: 14 days 
4) Maximum Annual Rate: 41.4 fl oz/A/year 
a. DO NOT apply more than 0.34 lb ai/A/year of propiconazole-containing products. 
b. DO NOT apply more than 1.5 lb ai/A/year of azoxystrobin-containing products. 
c. DO NOT apply more than 0.092 lb ai/A/year of benzovindiflupyr-containing products. 
5) DO NOT exceed 2 applications per year. 
6) Pre-harvest Interval (PHI) for Grain, hay, or silage: 14 days or R6, whichever is longest 
7) Aerial application is prohibited in New York State.

Trivapro Fungicide 
Page 35 
 
7.10 Sugarcane 
Crops (including all cultivars, varieties, and/or hybrids of these) [Not for use in California] 
Sugarcane 
Target Disease 
Rate 
(fl oz/A) Application Timing Use Directions 
Brown Rust 
(Puccinia 
melanocephela) 
 
Orange Rust 
(Puccinia kuehnii) 
10.7 - 20.7 
 
Apply prior to disease 
development. 
 
Continue applications 
through season on a 14 to 
28-day interval, following 
the resistance 
management guidelines. 
Apply by ground, air, or 
chemigation. 
 
An adjuvant may be added at 
directed rates. 
 
[Optional language if label has a 
single rate and interval range: If 
disease pressure is high, use the 
shortest interval.] 
Resistance Management: 
 DO NOT make more than two applications of Trivapro Fungicide or other Group 7 or 11 fungicides 
before alternation with a fungicide that is not in Group 7 or 11. 
USE RESTRICTIONS 
1) Refer to Section 6.1 for additional product use restrictions. 
2) Maximum Single Application Rate: 20.7 fl oz/A 
3) Minimum Application Interval: 14 days 
4) Maximum Annual Rate: 62.1 fl oz/A/year 
a. DO NOT apply more than 0.675 lb ai/A/year of propiconazole-containing products. 
b. DO NOT apply more than 0.80 lb ai/A/year of azoxystrobin-containing products. 
c. DO NOT apply more than 0.204 lb ai/A/year of benzovindiflupyr-containing products. 
5) DO NOT exceed 3 applications per year. 
6) Pre-harvest Interval (PHI): 30 days 
7) Aerial application is prohibited in New York State.

Trivapro Fungicide 
Page 36 
 
8.0 STORAGE AND DISPOSAL 
 
STORAGE AND DISPOSAL 
 
DO NOT contaminate water, food, or feed by storage or disposal. 
 
Pesticide Storage 
Store in original container only. Store in a cool, dry and well-ventilated place. Protect 
from excessive heat. Keep container closed when not in use. DO NOT store near food 
or feed. In case of spill on floor or paved surfaces, mop and remove to chemical waste 
storage area until proper disposal can be made if product cannot be used according to 
the label. 
 
Pesticide Disposal 
Pesticide wastes may be toxic or acutely hazardous. Improper disposal of unused 
pesticide, spray mixture, or rinse water is a violation of Federal Law. If these wastes 
cannot be used according to label instructions, contact your State Pesticide or 
Environmental Control Agency, or the Hazardous Waste representative at the nearest 
EPA Regional Office for guidance in proper disposal methods. 
 
Container Handling [equal to or less than 5 gallons] 
Non-refillable container. DO NOT reuse or refill this container. Offer for recycling if 
available. Triple rinse container (or equivalent) promptly after emptying. Triple rinse as 
follows: empty the remaining contents into application equipment of a mix tank and 
drain for 10 seconds after the flow begins to drip. Fill the container ¼ full with water and 
recap. Shake for 10 seconds. Pour rinsate into application equipment or a mix tank or 
store rinsate for later use or disposal. Drain for 10 seconds after the flow begin to drip. 
Repeat this procedure two more times. Then offer for recycling if available or puncture 
and dispose of in a sanitary landfill, or by incineration, or, by other procedures allowed 
by state and local authorities. 
 
Container Handling [greater than 5 gallons] 
Refillable container. Refill this container with pesticide only. DO NOT reuse this 
container for any other purpose. Cleaning the container before final disposal is the 
responsibility of the person disposing of the container. Cleaning before refilling is the 
responsibility of the refiller. To clean container before final disposal, empty the 
remaining contents from this container into application equipment or mix tank. Fill the 
container about 10 percent full with water. Agitate vigorously or recirculate water with 
the pump for 2 minutes. Pour or pump rinsate into application equipment or rinsate 
collection system. Repeat this rinsing procedure two more times. Then offer for 
recycling if available or puncture and dispose of in a sanitary landfill, or by incineration, 
or, by other procedures allowed by state and local authorities. 
 
Container Handling [greater than 5 gallons] 
Non-refillable container. DO NOT reuse or refill this container. Triple rinse container 
(or equivalent) promptly after emptying. Triple rinse as follows: Empty the remaining

Trivapro Fungicide 
Page 37 
 
contents into application equipment or a mix tank. Fill the container ¼ full with water. 
Replace and tighten closures. Tip container on its side and roll it back and forth, 
ensuring at least one complete revolution, for 30 seconds. Stand the container on its 
end and tip it back and forth several times. Turn the container over onto its other end 
and tip it back and forth several times. Empty the rinsate into application equipment or 
a mix tank or store rinsate for later use or disposal. Repeat this procedure two more 
times. Then offer for recycling if available or puncture and dispose of in a sanitary 
landfill, or by incineration, or by other procedures approved by state and local 
authorities. 
 
CONTAINER IS NOT SAFE FOR FOOD, FEED, OR DRINKING WATER. 
 
9.0 CONDITIONS OF SALE AND LIMITATION OF WARRANTY 
AND LIABILITY 
NOTICE: Read the entire Directions for Use and Conditions of Sale and Limitation of 
Warranty and Liability before buying or using this product. If the terms are not 
acceptable, return the product at once, unopened, and the purchase price will be 
refunded. 
 
The Directions for Use of this product must be followed carefully. It is impossible to 
eliminate all risks inherently associated with the use of this product. Crop injury, 
ineffectiveness or other unintended consequences may result because of such factors 
as manner of use or application, presence of other materials or other influencing factors 
in the use of the product, which are beyond the control of SYNGENTA CROP 
PROTECTION, LLC or Seller. To the extent permitted by applicable law, Buyer and 
User agree to hold SYNGENTA and Seller harmless for any claims relating to such 
factors. 
 
SYNGENTA warrants that this product conforms to the chemical description on the label 
and is reasonably fit for the purposes stated in the Directions for Use, subject to the 
inherent risks referred to above, when used in accordance with directions under normal 
use conditions. To the extent permitted by applicable law: (1) this warranty does not 
extend to the use of the product contrary to label instructions or under conditions not 
reasonably foreseeable to or beyond the control of Seller or SYNGENTA, and (2) Buyer 
and User assume the risk of any such use. TO THE EXTENT PERMITTED BY 
APPLICABLE LAW, SYNGENTA MAKES NO WARRANTIES OF MERCHANTABILITY 
OR OF FITNESS FOR A PARTICULAR PURPOSE, NOR ANY OTHER EXPRESS OR 
IMPLIED WARRANTY, EXCEPT AS WARRANTED BY THIS LABEL. 
 
To the extent permitted by applicable law, in no event shall SYNGENTA be liable for 
any incidental, consequential or special damages resulting from the use or handling of 
this product. TO THE EXTENT PERMITTED BY APPLICABLE LAW, THE 
EXCLUSIVE REMEDY OF THE USER OR BUYER, AND THE EXCLUSIVE LIABILITY 
OF SYNGENTA AND SELLER FOR ANY AND ALL CLAIMS, LOSSES, INJURIES 
OR DAMAGES (INCLUDING CLAIMS BASED ON BREACH OF WARRANTY,

Trivapro Fungicide 
Page 38 
 
CONTRACT, NEGLIGENCE, TORT, STRICT LIABILITY OR OTHERWISE) 
RESULTING FROM THE USE OR HANDLING OF THIS PRODUCT, SHALL BE THE 
RETURN OF THE PURCHASE PRICE OF THE PRODUCT OR, AT THE ELECTION 
OF SYNGENTA OR SELLER, THE REPLACEMENT OF THE PRODUCT. 
 
SYNGENTA and Seller offer this product, and Buyer and User accept it, subject to the 
foregoing Conditions of Sale and Limitation of Warranty and Liability, which may not be 
modified except by written agreement signed by a duly authorized representative of 
SYNGENTA. 
 
10.0 APPENDIX 
10.1 Trivapro Fungicide Rate Conversion Chart 
 
Fl oz 
Product/A 
Lb ai/A 
benzovindiflupyr 
Lb ai/A 
azoxystrobin 
Lb ai/A 
propiconazole 
Acres Treated 
per gallon 
9.4 0.018 0.067 0.076 13.6 
10.7 0.020 0.076 0.087 12 
12.8 0.025 0.092 0.104 10 
13.7 0.027 0.098 0.111 9.3 
20.7 0.040 0.148 0.168 6.2 
27.4 0.053 0.197 0.223 4.6 
27.6 0.054 0.198 0.224 4.6 
 
10.2 [optional text] Trivapro Fungicide Use Summary Table 
IMPORTANT: The table below is a summary of the Crop Use Directions for Trivapro 
Fungicide. However, it is important for the user to read and follow the complete 
instructions contained within this label.

Trivapro Fungicide 
Page 39 
 
Crop or Crop Group 
or Subgroup, with 
examples 
Maximum 
Rate per 
Application 
(fl oz/A) 
Minimum 
Application 
Interval 
(days) 
Pre-harvest 
Interval (PHI) 
Maximum Rate 
per Year 
(fl oz/A) 
Bulb Crop Group 3-
07; Dry Bulb Group 3-
07A; Onions, green 
Group 3-07B 
27.7 7 
Green Onion 
Group 3-07B: 7 
days 
Dry Bulb Group 
3-07A: 14 days 
55.4 
Rapeseed (Canola) 
Subgroup 20A 13.7 NA 30 days 23.5 
Cereals 
Barley, wheat 13.7 14 
Feekes 10.5.4 
 
Forage and hay: 
7 days 
27.4 
Corn (except sweet) 
Field corn, popcorn 13.7 14 
Forage, Grain, 
and Stover: 30 
days 
41.1 
Corn, sweet 13.7 14 Ears and 
Forage: 14 days 54.8 
Beans, Dry and 
Succulent (except 
soybean) 
Chickpea, lentil 
13.7 14 14 days 41.1 
Grasses Grown for 
Seed (bluegrass, 
bromegrass, fescue, 
orchardgrass, and 
ryegrass only) 
27.4 14 20 54.8 
Peanut 13.7 14 30 days 54.8 
Soybeans Grain: 20.7 
Forage and 
hay: 13.7 
14 
Grain: 14 days 
or R6, whichever 
is longest 
41.4 
Sugarcane 20.7 14 30 62.1

Trivapro Fungicide 
Page 40 
 
 
SOLATENOL®, Trivapro®, Acuron®, Callisto®, Lexar®, Lumax®, and the Syngenta 
Logo are Trademarks of a Syngenta Group Company 
 
Viton™ is a trademark of The Chemours Company FC, LLC 
 
©20XX Syngenta 
 
 
For non-emergency (e.g. current product information), call 
Syngenta Crop Protection at 1-866-796-4368. 
 
 
Manufactured for: 
Syngenta Crop Protection, LLC 
P.O. Box 18300 
Greensboro, North Carolina 27419-8300 
 
 
 
Trivapro Fungicide 1613 MAS 1221 AMEND-C 0823-CL –ep – 9-25-24 
000100-01613.20230818C.TRIVAPRO_FUNGICIDE-AMEND-0823-CL