crop-chem-docs/corpus/epa_ppls/100-1770.md

# STROVEQ

- EPA Reg No: **100-1770**
- Registrant: SYNGENTA CROP PROTECTION, LLC
- Signal word: Caution
- Active ingredients: Cerevisane (cell walls of Saccharomyces cerevisiae strain LAS117) (94.1%)
- Label accepted: 2025-08-22
- Source PDF: https://www3.epa.gov/pesticides/chem_search/ppls/000100-01770-20250822.pdf

---
U.S. ENVIRONMENTAL PROTECTION AGENCY 
Office of Pesticide Programs 
Biopesticides and Pollution Prevention Division (7511M) 
1200 Pennsylvania Ave., N.W. 
Washington, D.C. 20460 
EPA Reg. Number: 
 
100-1770 
 
Date of Issuance: 
 
8/22/2025 
NOTICE OF PESTICIDE: 
 X Registration 
 Reregistration 
Term of Issuance: 
Unconditional 
 (under FIFRA, as amended) Name of Pesticide Product: 
Stroveq 
Name and Address of Registrant (include ZIP Code): 
Syngenta Crop Protection, LLC 
P. O. Box 18300 
Greensboro, NC 27419 
 
Note: Changes in labeling differing in substance from that accepted in connection with this registration must be submitted to and accepted by the 
Biopesticides and Pollution Prevention Division prior to use of the label in commerce. In any correspondence on this product, always refer to the above 
EPA Registration Number. 
On the basis of information furnished by the registrant, the above named pesticide is hereby registered 
under the Federal Insecticide, Fungicide, and Rodenticide Act. 
Registration is in no way to be construed as an endorsement or recommendation of this product by the 
U.S. Environmental Protection Agency. In order to protect health and the environment, the 
Administrator, on his or her motion, may at any time suspend or cancel the registration of a pesticide 
in accordance with the Act. The acceptance of any name in connection with the registration of a 
product under the Act is not to be construed as giving the registrant a right to exclusive use of the 
name or to its use if it has been covered by others. 
This product is unconditionally registered in accordance with FIFRA section 3(c)(5) provided that you: 
1. Submit and/or cite all data required for registration or registration review of your product when 
EPA requires all registrants of similar products to submit such data. 
Signature of Approving Official: 
 
Gina Burnett, Senior Regulatory Advisor 
Biochemical Pesticide Branch 
Biopesticides and Pollution Prevention Division (7511M) 
Office of Pesticide Programs 
Date: 
 
8/22/2025 
EPA Form 8570-6

Page 2 of 2 
EPA Reg. No. 100-1770 
Action Case No. 00654434 
2. Make the following labeling change before you release this product for shipment: 
• Revise EPA Registration Number to read, “EPA Reg. No. 100-1770.” 
3. Submit one (1) copy of the final printed labeling for the record before you release this product 
for shipment. 
Should you wish to add/retain a reference to your company’s website on your label, then please be 
aware that the website becomes labeling under FIFRA and is subject to review by EPA. If the website is 
false or misleading, the product will be considered to be misbranded and sale or distribution of the 
product is unlawful under FIFRA section 12(a)(1)(E). 40 CFR § 156.10(a)(5) lists examples of statements 
EPA may consider false or misleading. In addition, regardless of whether a website is referenced on 
your product’s label, claims made on the website may not substantially differ from those claims 
approved through the registration process. Therefore, should EPA find or if it is brought to our 
attention that a website contains statements or claims substantially differing from statements or 
claims made in connection with obtaining a FIFRA section 3 registration, the website will be referred to 
EPA’s Office of Enforcement and Compliance Assurance. 
Your release for shipment of this product constitutes acceptance of these terms. If these terms are not 
complied with, this registration will be subject to cancellation in accordance with FIFRA section 6. A 
stamped copy of the labeling is enclosed for your records. Please also note that the record for this 
product currently contains the following acceptable Confidential Statement of Formula (CSF): 
• Basic CSF dated 03/04/2025 
If you have any questions, please contact Cecilia Kujawa via email at kujawa.cecilia@epa.gov. 
Sincerely, 
 
 
 
 
Gina Burnett, Senior Regulatory Advisor 
 Biochemical Pesticide Branch 
Biopesticides and Pollution 
Prevention Division (7511M) 
Office of Pesticide Programs

Bracketed text [] is optional 
 
STROVEQ® 
 
 
Systemic Resistance Inducer 
 
 [OMRI Listed™] [logo placeholder] 
 
For control of diseases of ornamental plants; ornamental bulb, corm and tuber crops; 
conifers; Christmas trees; listed small fruit, fruit and nut trees; and listed vegetable plants 
grown for retail sales to consumers. 
 
For application to field- and container grown plants produced in greenhouses and nurseries 
(including shade houses, lath houses and other outdoor growing structures), evergreen 
(including conifer) and deciduous tree nurseries, Christmas tree farms and ornamental 
grasses. 
 
Active Ingredients: 
Cerevisane (cell walls of Saccharomyces cerevisiae strain LAS117) ......................... 94.1% 
Other Ingredients: 5.9% 
Total: 100.0% 
 
Formulation: Wettable Powder (WP) 
 
KEEP OUT OF REACH OF CHILDREN. 
 
CAUTION/PRECAUCIÓN 
 
Si usted no entiende la etiqueta, busque a alguien para que se la explique a usted en detalle. 
(If you do not understand the label, find someone to explain it to you in detail.) 
[See] [inside] [label] [booklet] [for] [First Aid][,] [additional] [Precautionary Statements][,] [and] 
[Directions for Use] [including] [Storage and Disposal] [instructions][.] 
 
EPA Reg. No. 100-XXXX 
EPA Est. 
 
__________ 
Net Contents 
 
[Batch Code: _____ ] (For nonrefillables only.) 
08/22/2025
100-1770

TABLE OF CONTENTS 
 
1.0 FIRST AID 
PRECAUTIONARY STATEMENTS 
2.0 PRECAUTIONARY STATEMENTS 
2.1 Hazards to Humans and Domestic Animals 
2.2 Personal Protective Equipment (PPE) 
2.3 Engineering Controls 
2.4 User Safety Recommendations 
2.5 Environmental Hazards 
DIRECTIONS FOR USE 
3.0 PRODUCT INFORMATION 
4.0 APPLICATION DIRECTIONS 
4.1.1 Use Recommendations 
4.1.2 Mixing directions 
4.1.3 Tank mixing 
4.2 Chemigation [*Not Registered for use By California] 
4.2.1 Types of Irrigation Systems [*Not Registered for Use By California] 
4.2.2 Uniform Water Distribution and System Calibration [*Not Registered for Use By 
California] 
4.2.3 Required System Safety Devices [*Not Registered for Use By California] 
4.2.4 Using Water from Public Water Systems: [*Not Registered for Use By California] 
4.2.5 Injection for Chemigation [*Not Registered for Use By California] 
4.2.6 Center Pivot, Lateral Move, End Tow, Big Gun and Traveler Irrigation Equipment (Use 
only With Electric or Oil Hydraulic Drive Systems That Provide a Uniform Water Distribution 
[*Not Registered for Use By California] 
4.2.7 Solid Set, Side (Wheel) Roll and Hand Move Irrigation Equipment [*Not Registered for 
Use By California]
 
4.2.8 Flushing and Cleaning the Chemical Injection System [*Not Registered for Use By 
California]
 
5.0 RESTRICTIONS AND PRECAUTIONS 
5.1 Use Restrictions 
5.2 Use Precautions 
5.3 Spray Drift Management 
5.3.1 Spray Drift Advisories 
5.3.2 Importance of Droplet Size 
5.3.3 Controlling Droplet Size – Ground Boom 
5.3.4 Controlling Droplet Size – Aerial 
5.3.5 Boom Height – Ground Boom 
5.3.6 Boom Height – Aerial Boom 
5.3.7 Boom Width– Aerial 
5.3.8 Shielded Sprayers 
5.3.9 Temperature and Humidity

5.3.10 Temperature Inversions 
5.3.11 Wind 
5.3.12 Sensitive Areas 
6.0 USE DIRECTIONS 
6.1 TARGET PLANT DISEASES 
7.0 STORAGE AND DISPOSAL 
8.0 CONDITIONS OF SALE AND LIMITATION OF WARRANTY AND LIABILITY

1.0 FIRST AID 
FIRST AID 
If swallowed • Call a poison control center or doctor immediately for treatment advice. 
• Have person sip a glass of water if able to swallow. 
• Do not induce vomiting unless told to do so by a poison control 
center or doctor. 
• Do not give anything by mouth to an unconscious person. 
If in eyes • Hold eye open and rinse slowly and gently with water for 15-20 
minutes. 
• Remove contact lenses, if present, after the first 5 minutes, then 
continue rinsing eye. 
• Call a poison control center or doctor for treatment advice. 
Have the product container or label with you when calling a poison control center or 
doctor or going for treatment. 
SYNGENTA HOTLINE NUMBER 
For 24-Hour Medical Emergency Assistance (Human or Animal) or Chemical 
Emergency Assistance (Spill, Leak, Fire, or Accident), 
Call 
1-800-888-8372 
 
PRECAUTIONARY STATEMENTS 
 
2.0 PRECAUTIONARY STATEMENTS 
2.1 Hazards to Humans and Domestic Animals 
CAUTION/PRECAUCIÓN 
Harmful if swallowed. Causes moderate eye irritation. Avoid contact with eyes or 
clothing. Wash thoroughly with soap and water after handling and before eating, 
drinking, chewing gum, using tobacco or using the toilet. 
 
2.2 Personal Protective Equipment (PPE) 
Applicators and other handlers must wear: 
• long-sleeved shirt and long pants 
• protective eyewear 
• waterproof gloves 
• shoes plus socks 
 
2.3 Engineering Controls 
When handlers use closed systems, enclosed cabs, or aircraft in a manner that meets 
the requirements listed in the Worker Protection Standard (WPS) for agricultural

pesticides (40CFR 170.607(d), (e) and (f)), the handler PPE requirements may be 
reduced or modified as specified in the WPS. 
 
IMPORTANT: When reduced PPE is worn because a closed system is being used, 
users must be provided all PPE specified above and have such PPE immediately 
available for use in an emergency, such as a spill or equipment break-down 
 
Follow the manufacturer’s instructions for cleaning/maintaining PPE. If no such 
instructions for washables are available, use detergent and hot water. Keep and 
wash PPE separately from other laundry. 
 
2.4 User Safety Recommendations 
User Safety Recommendations 
 
Users should: 
• Remove clothing/PPE immediately if pesticide gets inside. Then wash thoroughly 
and put on clean clothing. 
• Remove PPE immediately after handling this product. Wash the outside of gloves 
before removing. As soon as possible, wash thoroughly and change into clean 
clothing. 
 
2.5 Environmental Hazards 
For terrestrial uses - Do not apply directly to water, or to areas where surface water 
is present or to intertidal areas below the mean high- water mark. Do not 
contaminate water when disposing of equipment washwater or rinsate.

DIRECTIONS FOR USE 
 
It is a violation of federal law to use this product in a manner inconsistent with its labeling. 
For any requirements specific to your state or tribe, consult the state or tribal 
agency responsible for pesticide regulation. Do not apply this product in a way 
that will contact workers or other persons, either directly or through drift. Only 
protected handlers may be in the area during application. 
Notify state and/or federal authorities and Syngenta immediately if you observe any 
adverse environmental effects due to use of this product. 
 
FAILURE TO FOLLOW THE DIRECTIONS FOR USE AND PRECAUTIONS ON THIS 
LABEL MAY RESULT IN CROP INJURY, POOR WEED CONTROL, AND/OR ILLEGAL 
RESIDUES. 
 
AGRICULTURAL USE REQUIREMENTS 
Use this product only in accordance with its labeling and with the Worker Protection 
Standard, 40 CFR Part 170. This Standard contains requirements for the protection 
of agricultural workers on farms, forests, nurseries, and greenhouses, and handlers of 
agricultural pesticides. It contains requirements for training, decontamination, 
notification, and emergency assistance. It also contains specific instructions and 
exceptions pertaining to the statements on this label about personal protective 
equipment (PPE) and restricted-entry interval. The requirements in this box only 
apply to uses of this product that are covered by the Worker Protection Standard. 
Do not enter or allow worker entry into treated areas during the restricted-entry 
interval (REI) of 4 hours. 
PPE required for early entry to treated areas that is permitted under the Worker 
Protection Standard and that involves contact with anything that has been treated, such 
as plants, soil or water is: 
• Coveralls 
• Protective eyewear 
• Waterproof gloves 
• Shoes plus socks 
 
 
 
3.0 PRODUCT INFORMATION 
Stroveq is a Systemic Resistance Inducer (SRI) that acts preventively. Its active 
ingredient (CEREVISANE – cell walls of Saccharomyces cerevisiae strain LAS117) 
strongly induces plant defense mechanisms, and so prepares the plant to defend 
itself against fungal and bacterial attacks.

4.0 APPLICATION DIRECTIONS 
Stroveq can be applied as a foliar spray to field or greenhouse crops. Stroveq can be applied 
through various types of chemigation application as described in the Chemigation section of 
this label. 
 
Apply using conventional spray equipment, using a sufficient volume of mixture to ensure 
complete coverage of vegetation without run-off. The amount of spray solutions necessary will 
depend on the type of crop. Full canopy coverage is required. Some crops and/or canopy 
coverage might require up to 400 gallons of spray per acre. If possible, apply the product on 
both faces of the leaves and preferably early in the morning. Stroveq is rainfast within 2 hours 
after treatment. 
 
4.1.1 Use Recommendations 
Apply STROVEQ as a preventative treatment. 
Spray interval: 7-14 days depending on the disease pressure and environmental conditions. 
In case of high pressure/risk, STROVEQ should be used in program with other fungicides 
(alternation or tank- mix). 
Stroveq has been evaluated for phytotoxicity on a variety of crops under various normal 
growing conditions. However, testing all crop varieties, in all mixtures and combinations, is 
not feasible. Prior to treating entire crop, test a small portion of the crop for sensitivity. 
 
4.1.2 Mixing directions 
Important – Do not add Stroveq to the spray tank before introducing the correct amount of 
water. 
Add water to the spray tank. Start the mechanical or hydraulic agitation to provide moderate 
circulation before adding Stroveq. Maintain circulation while loading and spraying. Do not mix 
more Stroveq than can be used in 24 hours. 
Always ensure the sprayer is clean according to standard cleaning procedures, in good 
working order and calibrated accurately to the sprayer manufacturer recommendations. 
 
4.1.3 Tank mixing 
Do not combine Stroveq in the spray tank with other pesticides, surfactants, adjuvants, or 
fertilizers if there has been no previous experience or use of the combination to show it is 
physically compatible, effective, and non-injurious under your use conditions.

Follow the most restrictive of the labeling limitations and precautions of all products used in 
mixtures. 
To ensure compatibility of tank-mix combinations, they must be evaluated prior to use. To 
determine the physical compatibility of this product with other products, use a jar test. Using a 
quart jar, add the proportionate amounts of the products to one quart of water with agitation. 
Add dry formulations first, then flowables, and then emulsifiable concentrates last. After 
thoroughly mixing, let this mixture stand for 5 minutes. If the combination remains mixed or 
can be readily remixed, it is physically compatible. Once compatibility has been proven, use 
the same procedure for adding required ingredients to the spray tank. 
Test the mix on a small portion of the crop to be treated to ensure that a phytotoxic response 
will not occur as a result of the application. 
 
4.2 Chemigation [*Not Registered for use By California] 
4.2.1 Types of Irrigation Systems [*Not Registered for Use By California] 
This product can be applied through sprinkler including center pivot, lateral move, end tow, 
side (wheel) roll, traveler, big gun, solid set, or hand move. Do not apply this product through 
any type of irrigation system. Maintain agitation during mixing and application to ensure 
uniform product suspension. Use the application rate indicated in the Crop-Specific Use 
Directions of this label. Use sufficient water to achieve thorough coverage. 
4.2.2 Uniform Water Distribution and System Calibration [*Not Registered 
for Use By California] 
The chemigation system must provide uniform distribution of treated water. Crop injury or 
lack of effectiveness can result from non-uniform distribution of treated water. If you have 
questions about calibration, you should contact State Extension Service specialists, 
equipment manufacturers or other experts. Do not connect an irrigation system (including 
greenhouse systems) used for pesticide application to a public water system unless the 
pesticide label-prescribed safety devices for public water systems are in place. A person 
knowledgeable of the chemigation system and responsible for its operation or under the 
supervision of the responsible person, shall shut down and make necessary adjustments 
should the need arise. 
 
4.2.3 Required System Safety Devices [*Not Registered for Use By 
California] 
The system must contain a functional check valve, a vacuum relief valve and a low-pressure 
drain appropriately located on the irrigation pipeline to prevent water source contamination 
from backflow. The pesticide injection pipeline must contain a functional, automatic, quick-
closing check valve to prevent the flow of fluid back toward the injection pump. The pesticide 
injection pipeline must also contain a functional, normally closed, solenoid-operated valve 
located on the intake side of the injection pump connected to the system interlock to prevent

fluid from being withdrawn from the supply tank when the irrigation system is either 
automatically or manually shut down. The system must contain functional interlocking 
controls to automatically shut off the pesticide injection pump when the water pump motor 
stops. The irrigation line or water pump must include a functional pressure switch which will 
stop the water pump motor when the water pressure decreases to the point where pesticide 
distribution is adversely affected. Systems must use a metering pump, such as a positive 
displacement injection pump (e.g., diaphragm pump) effectively designed and constructed of 
materials that are compatible with pesticides and capable of being fitted with a system 
interlock. Do not apply when wind speed favors drift beyond the area intended for treatment. 
 
4.2.4 Using Water from Public Water Systems: [*Not Registered for Use By 
California] 
Do not connect an irrigation system (including greenhouse systems) used for pesticide 
application to a public water system unless the pesticide label-prescribed safety devices for 
public water systems are in place. 
Public water system means a system for the provision to the public of piped water for human 
consumption if such system has at least 15 service connections or regularly serves an 
average of at least 25 individuals daily at least 60 days out of the year. Chemigation systems 
connected to public water systems must contain a functional, reduced-pressure zone, back 
flow preventer (RPZ) or the functional equivalent in the water supply line upstream from the 
point of pesticide introduction. As an option to the RPZ, the water from the public water 
system should be discharged into a reservoir tank prior to pesticide introduction. There shall 
be a complete physical break (air gap) between the flow outlet end of the fill pipe and the top 
or overflow rim of the reservoir tank of at least twice the inside diameter of the fill pipe. The 
pesticide injection pipeline must contain a functional, automatic, quick-closing check valve to 
prevent the flow of fluid back toward the injection. The pesticide injection pipeline must 
contain a functional, normally closed, solenoid-operated valve located on the intake side of 
the injection pump and connected to the system interlock to prevent fluid from being 
withdrawn from the supply tank when the irrigation system is either automatically or manually 
shut down. The system must contain functional interlocking controls to automatically shut off 
the pesticide injection pump when the water pump motor stops, or in cases where there is no 
water pump, when the water pressure decreases to the point where pesticide distribution is 
adversely affected. Systems must use a metering pump, such as a positive displacement 
injection pump (e.g., diaphragm pump) effectively designed and constructed of materials that 
are compatible with pesticides and capable of being fitted with a system interlock. Do not 
apply when wind speed favors drift beyond the area intended for treatment. 
 
4.2.5 Injection for Chemigation [*Not Registered for Use By California] 
Inject the specified dosage of STROVEQ into the irrigation main water stream: (1) through a 
constant flow meter devices; (2) into the center of the main line flow via a pivot tube or

equivalent; (3) at a point ahead of at least one right-angle turn in the mainstream flow such 
that thorough mixing with the irrigation water is ensured. 
 
4.2.6 Center Pivot, Lateral Move, End Tow, Big Gun and Traveler Irrigation 
Equipment (Use only With Electric or Oil Hydraulic Drive Systems 
That Provide a Uniform Water Distribution [*Not Registered for Use 
By California] 
• Determine the size of area to be treated. 
• Ensure that your system is properly calibrated. 
• Determine the amount of STROVEQ required to treat area. 
• Add required amount of STROVEQ and sufficient water to meet the injection time 
requirements of the solution tank. 
• Maintain constant solution tank agitation during the injection period. 
• Stop injection equipment after treatment is completed. Continue to operate the 
system until STROVEQ solution has cleared the sprinkler head. 
 
4.2.7 Solid Set, Side (Wheel) Roll and Hand Move Irrigation Equipment 
[*Not Registered for Use By California] 
• Determine acreage covered by sprinkler. 
• Fill injector solution tank with water. 
• Determine the amount of STROVEQ required to treat area. 
• Add the required amount of STROVEQ into the same quantity of water used to 
calibrate the injection equipment. 
• Maintain constant solution tank agitation during the injection period. 
• Operate system at normal pressures specified by the manufacturer of the injection 
equipment and used for the time interval established during calibration. 
• Injection STROVEQ at the end of the irrigation cycle or as a separate application to 
maximize foliar fungicide retention. 
• Stop injection equipment after treatment is completed. Continue to operate the 
system until STROVEQ solution has cleared the last sprinkler head. 
 
4.2.8 Flushing and Cleaning the Chemical Injection System [*Not 
Registered for Use By California] 
At the end of the application period, allow time for all lines to flush the pesticide through all 
nozzles or emitters before turning off irrigation water. To ensure the lines are flushed and free 
of pesticides, a dye indicator may be injected into the lines to mark the end of the application 
period. 
In order to apply pesticides accurately, the chemical injection system must be kept clean and 
free of chemical or fertilizer residues and sediments. Refer to your owner’s manual or ask 
your equipment supplier for the cleaning procedure for your injection system.

5.0 RESTRICTIONS AND PRECAUTIONS 
5.1 Use Restrictions 
• DO NOT apply to through any type of irrigation systems (chemigation). 
 
5.2 Use Precautions 
• Under certain conditions conducive to extended infection periods, use another 
registered fungicide for additional applications if maximum amount of Stroveq has 
been used. 
• The higher rates in the rate range and/or shorter spray intervals may be required 
under conditions of heavy infection pressure, with highly susceptible varieties, or 
when environmental conditions are conducive to disease. 
• DO NOT apply through cold fogger equipment 
• DO NOT apply through any ultra-low volume (ULV) spray system 
 
5.3 Spray Drift Management 
 
5.3.1 Spray Drift Advisories 
 
THE APPLICATOR IS RESPONSIBLE FOR AVOIDING OFF-SITE SPRAY DRIFT. 
BE AWARE OF NEARBY NON-TARGET SITES AND ENVIRONMENTAL CONDITIONS. 
 
5.3.2 Importance of Droplet Size 
An effective way to reduce spray drift is to apply large droplets. Use the largest droplets that 
provide target pest control. While applying larger droplets will reduce spray drift, the potential 
for drift will be greater if applications are made improperly or under favorable environmental 
conditions.
 
5.3.3 Controlling Droplet Size – Ground Boom 
• Volume – Increasing the spray volume so that larger droplets are produced will reduce 
spray drift. Use the highest practical spray volume for the application. If greater spray 
volume is needed, consider using a nozzle with a higher flow rate. 
• Pressure – Use the lowest spray pressure specified for the nozzle to produce the target 
spray volume and droplet size. 
• Spray Nozzle – Use a spray nozzle that is designed for the intended application. 
Consider using nozzles designed to reduce drift. 
 
 
5.3.4 Controlling Droplet Size – Aerial 
Use high flow rate nozzles to apply the highest practical spray volume. Nozzles with higher 
rated flows produce larger droplets. Do not exceed the nozzle manufacturer’s recommended

pressures. For many nozzle types, lower pressure produces larger droplets. When high flow 
rates are needed, use higher flow rate nozzles instead of increasing pressure. Use the 
minimum number of nozzles that provide uniform coverage. Orienting nozzles so that the 
spray is released parallel to the airstream produces larger droplets than other orientations 
and is the recommended practice. Significant deflection from horizontal will reduce droplet 
size and increase drift potential. Use a nozzle type that is designed for the intended 
application. With most nozzle types, narrower spray angles produce larger droplets. Consider 
using low-drift nozzles. Solid stream nozzles oriented straight back produce the largest 
droplets and lowest drift. 
5.3.5 Boom Height – Ground Boom 
For ground equipment, the boom should remain level with the crop and have minimal bounce. 
 
5.3.6 Boom Height – Aerial Boom 
Do not make application at a height greater than 10 feet above the top of the largest plants 
unless a greater height is required for aircraft safety. Making applications at the lowest height 
that is safe reduces exposure to droplets to evaporation and wind. 
 
5.3.7 Boom Width– Aerial 
For aerial applications, the boom width must not exceed 75% of the wingspan or 90% of the 
rotary blade. Use upwind swatch displacement and apply only when wind speed is 3-10 mph 
as measured by an anemometer. Use medium or coarser spray according to ASAE 572 
definition for standard nozzles or VMD for spinning atomizer nozzles. If application includes a 
no-spray zone, do not release spray at a height greater than 10 feet above the ground or crop 
canopy. 
5.3.8 Shielded Sprayers 
Shielding the boom or individual nozzles can reduce spray drift. Consider using shielded 
sprayers. Verify that the shields are not interfering with the uniform deposition of the spray on 
the target area.
 
5.3.9 Temperature and Humidity 
When making applications in hot and dry conditions, use larger droplets to reduce effects of 
evaporation. 
5.3.10 Temperature Inversions 
Drift potential is high during a temperature inversion. Temperature inversions are 
characterized by increasing temperature with altitude and are common on nights with limited 
cloud cover and light to now wind. The presence of an inversion can be indicated by ground 
fog or by the movement of smoke from a ground source or an aircraft smoke generator. 
Smoke that layers and moves laterally in a concentrated cloud (under low wind conditions)

indicates an inversion, while smoke that moves upward and rapidly dissipates indicates good 
vertical air mixing. Avoid applications during temperature inversions. 
5.3.11 Wind 
Drift potential increases with wind speed. AVOID APPLICATIONS DURING GUSTY WIND 
CONDITIONS. Applicators need to be familiar with local wind patterns and terrain that could 
affect spray drift. 
5.3.12 Sensitive Areas 
The pesticide should only be applied when the potential for drift to adjacent sensitive areas 
(e.g. residential areas, bodies of water, known habitat for threatened or endangered species, 
nontarget crops) is minimal (e.g., when wind is blowing away from the sensitive areas). Do 
not allow spray to drift from the application site and contact people, structures people occupy 
at any time and the associated property, parks and recreation areas, non-target crops, 
aquatic and wetland areas, woodlands, pastures, rangelands, or animals. 
 
 
6.0 USE DIRECTIONS 
6.1 TARGET PLANT DISEASES 
Alternaria spp. [*]; Anthracnose (Colletotrichum spp.)[*]; Asian soybean rust[*]; Black 
sigatoka[*]; Blast[*]; Botrytis[*]; Brown spot[*]; Cercospora[*];Coffee berry (Colletotrichum 
spp.)[*]; Dollar spot[*]; Downy mildew[*]; Early blight[*]; Fire blight[*]; Frogeye leaf spot[*]; 
Fusarium[*]; Gray leafspot[*]; Greasy spot[*]; Helminthosporium leaf spot[*]; Late 
blight[*]; Melanose[*]; Brown Rot/Blossom Blight (Monilinia spp.)[*]; Phytophthora[*]; 
Powdery mildew[*]; Post-bloom Fruit Drop (PFD)[*]; Rhizoctonia[*]; Rust[*]; Ramularia[*]; 
Scab[*]; Scald[*]; Smut[*]; Sour rot[*]; Stem rot[*]; Target spot [*]; White mold[*]. 
[*Not registered for Use By California] 
APPLICATION RATES 
Thoroughly cover plant foliage with spray solution. Pre-harvest Interval (PHI) = 0 days. 
 
CROPS TARGET DISEASES APPLICATION RATE 
Berries and Small Fruits 
Group and Subgroup[*]: 
Blackberry; Blueberry; 
Bushberry; Caneberry; 
Cranberry; Currant; Elderberry; 
Gooseberry; Huckleberry; 
Loganberry; Raspberry; 
Strawberry 
[*Not Registered for Use By 
California] 
Alternaria (Alternaria spp.)[*] 
Anthracnose (Colletotrichum 
spp.)[*] 
Botrytis (Botrytis spp.)[*] 
Downy mildew (Peronospora 
spp.)[*] 
Mummy berry (Monilinia spp.)[*] 
Powdery mildew[*] 
Rust (Pucciniastrum spp.)[*] 
 
0.45 - 0.68 lb/acre

Brassica Head and Stem 
Vegetable Group and 
Subgroup [*] Broccoli; 
Brussels sprouts; Cabbage; 
Cabbage, Chinese, napa; 
Cauliflower; Cultivars, 
varieties, and/or hybrids of 
these. 
[*Not Registered for Use By 
California] 
Alternaria (Alternaria spp.)[*] 
Anthracnose (Colletotrichum 
spp.)[*] 
Bottom rot (Rhizoctonia spp.)[*] 
Cercospora (Cercospora spp.)[*] 
Downy mildew (Peronospora 
spp.)[*] 
Fusarium (Fusarium spp.)[*] 
Powdery mildew[*] 
White mold (Sclerotinia spp.)[*] 
0.23 - 0.68 lb/acre 
Bulb Vegetables Group and 
Subgroup[*]: Chive, fresh 
leaves; Chive, Chinese, fresh 
leaves; Daylily, bulb; Elegans 
hosta; Fritillaria, bulb; Fritillaria, 
leaves; Garlic, bulb; Garlic, 
great headed, bulb; Garlic, 
Serpent, bulb; Kurrat; Lady's 
leek; Leek Allium porrum; Leek, 
wild; Lily, bulb; Onion, Beltsville 
bunching; Onion, bulb; Onion, 
Chinese, bulb; Onion, fresh; 
Onion, green; Onion, 
macrostem; Onion, pearl; 
Onion, potato, bulb; Onion, tree, 
tops; Onion, Welsh; Shallot, 
bulb; Shallot, fresh leaves; 
cultivars, varieties, and/or 
hybrids of these. 
[*Not Registered for Use By 
California] 
 Anthracnose (Colletotrichum 
spp.)[*] 
Botrytis (Botrytis spp.)[*] 
Cercospora (Cercospora spp.)[*] 
Downy mildew (Peronospora 
spp.)[*] 
Fusarium (Fusarium spp.)[*] 
Powdery Mildew[*] 
Purple blotch (Alternaria spp.)[*] 
Rhizoctonia (Rhizoctonia spp.)[*] 
Sclerotinia rot (Sclerotinia spp.)[*] 
0.23-0.91 lb/acre

Cereal Grains- Group and 
Subgroup[*]: Barley; 
buckwheat; corn; millet, pearl; 
millet, proso; oats; popcorn; rice; 
rye; sorghum (milo); teosinte; 
triticale; wheat; wild rice 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
[*Not Registered for Use By 
California] 
Powdery Mildew (Blumeria spp); 
Erysiphie graminis)[*] 
Fusarium (Fusarium spp.)[*] 
Rust (Puccinia spp.)[*] 
Brown spot (Septoria spp.)[*] 
Brown leaf spot (Drechslera 
spp.)[*] 
Scald (Rhynchosporium spp.)[*] 
Ramularia (Ramularia spp.)[*] 
Corn smut (Ustilago spp.)[*] 
Mycosphaerella 
(Mycosphaerella spp.)[*] 
Magnaporthe 
(Magnaporthe spp.)[*] 
Smut (Tilletia spp.)[*] 
Anthracnose (Glomerella spp.)[*] 
Blast (Pyricularia spp.)[*] 
Sheath Spot and Blight[*] 
(Rhizoctonia spp.)[*] 
(Thanatephorus kernel)[*] 
(Anamorph: Rhizoctonia solani)[*] 
Stem Rot (Sclerotium oryzae)[*] 
Brown Rot, Leaf Spots and 
Smuts[*] 
(Cercospora spp.)[*] 
(Entyloma spp.)[*] 
(Cochliobolus spp.)[*] 
(Ceratobasidium spp.)[*] 
0.23-0.91 lb/acre 
Citrus fruit Group and 
Subgroup[*]: 
Calamondin; citrus citron; citrus 
hybrids (includes chironja, 
tangelo, tangor); grapefruit; 
kumquat; lemon; lime; 
mandarin (tangerine); orange, 
sour; orange, sweet; pummelo; 
Satsuma mandarin; Cultivars, 
varieties, and/or hybrids of these. 
[*Not Registered for Use By 
California] 
Phytophthora 
(Phytophthora spp.)[*] 
Botrytis (Botrytis spp.)[*] 
Monilinia (Monilinia spp.)[*] 
Greasy spot 
(Mycosphaerella spp.)[*] 
Scab (Elisnoe spp.)[*] 
Alternaria (Alternaria 
spp.)[*] 
Melanose (Diaporthe 
spp.)[*] Post-bloom Fruit 
Drop (PFD)[*] 
Colletotrichum acutatum[*] 
Canker (xanthomonas 
axonopodis pv citri)[*] 
0.23-0.91 lb/acre

Coffee[*] 
 
[*Not Registered for Use By 
California] 
Anthracnose/Coffee berry 
(Colletotrichum spp.)[*] 
Rust (Hemileia spp.)[*] 
0.23-0.91 lb/acre 
Cucurbit Vegetables Group 
and Subgroup: Cucumbers; 
Melons; Gourds; Pumpkins; 
Squash; Zucchini; Cultivars, 
varieties, and/or hybrids of 
these. 
 
[*Not Registered for Use By 
California] 
Alternaria (Alternaria 
spp.)[*] 
Anthracnose 
(Colletotrichum spp.)[*] 
Botrytis (Botrytis spp.)[*] 
Cercospora (Cercospora 
spp.)[*] 
Downy mildew 
(Pseudoperonospora 
spp.)[*] 
Fusarium (Fusarium 
spp.)[*] 
Powdery Mildew[*] 
0.45 lb/acre 
Fruiting Vegetables Group and 
Subgroup[*]: 
Eggplant; Okra; Sweet and hot 
Peppers; Tomatillos; Tomatoes; 
Cultivars, varieties, and/or 
hybrids of these. 
[*Not Registered for Use By 
California] 
Alternaria (Alternaria 
solani)[*] 
Anthracnose 
(Colletotrichum spp.)[*] 
Botrytis (Botrytis spp.)[*] 
 Downy mildew[*] 
Late blight (Phytophthora 
spp.)[*] 
Powdery Mildew[*] 
Rhizoctonia foliar blight 
(Rhizoctonia spp.)[*] 
Target spot (Corynespora 
spp.)[*] 
0.45 - 0.68 lb/acre 
Grapevine and Table Grapes 
 
[*Not Registered for Use By 
California] 
Botrytis (Botrytis spp.)[*] 
Downy mildew 
(Plasmopara spp.)[*] 
Powdery mildew[*] 
Sour rot[*] 
0.23 lb/acre 
Hemp[*]: 
 
[*Not Registered for Use By 
California] 
Powdery Mildew 
(Golovinomyces spp.)[*] 
Botrytis (Botrytis spp.)[*] 
Cercospora (Cercospora 
spp.)[*] White mold 
(Sclerotinia spp.)[*] 
0.23-0.91 lb/acre 
Hop[*]: 
 
[*Not Registered for Use By 
California] 
Powdery Mildew 
(Podosphaera spp.)[*] 
Downy Mildew 
(Pseudoperonospora 
spp.)[*] 
Botrytis (Botrytis spp.)[*] 
0.23-0.91 lb/acre

Phytophthora 
(Phytophthora spp.)[*] 
Herbs and Spices Group and 
Subgroup[*]: Angelica; Balm; 
Basil; Borage; Burnet; 
Chamomile; Catnip; Chervil; 
Chive; Clary; Coriander; 
Costmary; Cilantro; Curry; 
Dillweed; Horehound; Hyssop; 
Lavender; Lemongrass; Lovage; 
Marjoram; Nasturtium; Parsley 
(dried); Peppermint; Rosemary; 
Sage; Savory (summer and 
winter); Sweet bay; Tansy; 
Tarragon; Thyme; Wintergreen; 
Woodruff; Wormwood; Cultivars, 
varieties, and/or hybrids of these. 
[*Not Registered for Use By 
California]. 
Botrytis (Botrytis spp.)[*] 
Downy mildew 
(Pseudoperonospora spp., 
Peronospora spp.) [*] 
Powdery mildew[*] 
0.23 - 0.68 lb/acre 
Leafy Vegetables and Cole 
Crops Group and 
Subgroup[*]: 
Arugula; Celery; Chervil; 
Endive; Fennel; Lettuce (head 
and leaf); Parsley; Radicchio; 
Rhubarb; Spinach; Swiss 
Chard; Collards; Kale; Kohlrabi 
Mustard Greens; Asparagus; 
Mizuna; cultivars, varieties, 
and/or hybrids of these 
[*Not Registered for Use By 
California] 
Alternaria (Alternaria 
spp.)[*] 
Anthracnose 
(Colletotrichum spp.)[*] 
Botrytis (Botrytis spp.)[*] 
Downy mildew (Bremia 
spp., Peronospora spp.)[*] 
Powdery Mildew[*] 
Rhizoctonia (Rhizoctonia 
spp.)[*] 
Sclerotinia rot (Sclerotinia 
spp.)[*] 
0.45 - 0.68 lb/acre 
Legume Vegetables 
(Succulent or Dried) Group 
and Subgroup[*]: Bean; Broad 
bean (fava); Chickpea; Guar; 
Jackbean; Lablab bean; Lentil; 
Pea; Pigeon pea; Soybean; 
Sword bean; Cultivars, varieties 
and/or hybrids of these. 
 
[*Not Registered for Use By 
California] 
Alternaria (Alternaria 
spp.)[*] 
Anthracnose 
(Colletotrichum spp.)[*] 
Asian Soybean Rust 
(Phakospora spp.)[*] 
Botrytis (Botrytis spp.)[*] 
Brown spot (Pseudomonas 
spp.)[*] 
Cercospora – Frogeye leaf 
spot 
(Cercospora spp.)[*] 
Phytophthora 
(Phytophthora spp.)[*] 
Powdery mildew 
(Microsphaera spp., 
Erysiphe spp.)[*] 
Rust (Uromyces spp.)[*] 
0.23 - 0.68 lb/acre

White mold (Sclerotinia 
spp.)[*] 
Oilseed Group and 
Subgroup[*]: Borage; 
calendula; canola; castor 
oil plant; Chinese 
tallowtree; cottonseed; crambe; 
cuphea; echium; euphorbia; 
evening primrose; flax seed; 
gold of pleasure; hare’s ear; 
mustard; jojoba; lesquerella; 
lunaria; meadowfoam; 
milkweed; mustard seed; niger 
seed; oil radish; poppy seed; 
rapeseed; rose hip; safflower; 
sesame; stokes aster; 
sunflower; sweet rocket; 
tallowwood; tea oil plant; 
Vernonia; cultivars, varieties, 
and/or hybrids of these 
[*Not Registered for Use By 
California] 
Alternaria (Alternaria 
spp.)[*] 
Anthracnose (Glomerella 
spp.)[*] 
Brown Spot (Septoria 
spp.)[*] 
Cercospora (Cercospora 
spp.)[*] 
Cylindrosporium spp.[*] 
Downy mildew 
(Plasmospora spp., 
Peronospora spp.)[*] 
Mycosphaerella spp.[*] 
Phoma spp.[*] 
Pod and Stem Blight 
(Diaporthe spp.; 
Phomopsis spp.)[*] 
Powdery Mildew (Erysiphe 
spp.)[*] 
Rhizoctonia (Rhizoctonia 
spp.)[*] 
Rust (Puccinia spp.)[*] 
White Mold (Sclerotinia 
spp.)[*] 
 
0.23-0.91 lb/acre 
Ornamentals plants group[*] 
Breeding crops; Bulb crops, Cut 
flowers, Evergreens (including 
conifers); Flowering plants, 
Flowers grown for seed 
production, Foliage plants, 
Ground covers, Ornamental 
grasses, Ornamental trees and 
shrubs; Palms, Perennial 
Shrubs, Pot and Bedding plants 
(annuals and perennials); 
Succulent plants 
Botrytis (Botrytis spp.)[*] 
Powdery mildew[*] 
Downy mildew[*] 
Scab[*] 
Alternaria (Alternaria 
spp.)[*] 
Rust[*] 
Cercospora (Cercospora 
spp.)[*] 
Rust (Puccinia spp.)[*] 
Scab (Elsinoe spp.)[*] 
0.23-0.91 lb/acre

[*Not Registered for Use By 
California] 
Peanut[*]: 
 
[*Not Registered for Use By 
California] 
Early leaf spot (Cercospora 
spp.)[*] 
Late leaf spot (Cercosporidium 
personatum)[*] 
Downy Mildew (Peronospora 
spp.) [*] 
Rust (Puccinia arachidis)[*] 
Brown Spot (Septoria spp.)[*] 
White Mold (Sclerotinia spp.)[*] 
Botrytis (Botrytis spp.)[*] 
Stem Rot/Southern Blight (Sclerotium 
spp.)[*] 
0.23-0.91 lb/acre 
Pome Fruits Group and 
Subgroup[*]: Apple; Azarole; 
Crabapple; Loquat; Mayhaw; 
Hook. & Arn.; Medlar; Pear; 
Pear, Asian; Pseudocydonia 
sinensis; Quince; Quince, 
Chinese; Quince, Japanese; 
Tejocate; cultivars, varieties 
and/or hybrids of these. 
[*Not Registered for Use By 
California] 
Alternaria (Alternaria spp.)[*] 
Anthracnose (Colletotrichum 
spp.)[*] 
Bitter Rot (Colletotrichum 
spp.)[*] 
Scab (Venturia spp.)[*] 
Botrytis (Botrytis spp.)[*] 
Fire blight 
(Erwinia spp.)[*] 
Powdery mildew[*] 
0.23 - 0.91 lb/acre 
Root and Tuber Vegetables 
Group and Subgroup[*]: 
Arracacha; Arrowroot; 
Artichoke; Artichoke, Chinese; 
Artichoke, Jerusalem; Beet, 
garden; Beet, sugar; Burdock, 
edible; Canna, edible; Carrot; 
Cassava, bitter and sweet; 
Celeriac (celery root) 
; Chayote (root); Chervil, turnip- 
rooted; Chicory; Chufa; 
Dasheen (taro); Ginger; 
Ginseng; Horseradish; Leren; 
Parsley, turnip-rooted; Parsnip; 
Potato; Radish; Radish, oriental 
(daikon); Rutabaga; Salsify 
(oyster plant); Salsify, black; 
Salsify, Spanish; Skirret; Sweet 
potato; Tanier; Tumeric; Turnip; 
Yam bean; Yam, true; 
Cultivars, varieties, and/or 
hybrids of these. 
[*Not Registered for Use By 
California] 
Black dot (Colletotrichum spp.)[*] 
Cercospora (Cercospora spp.)[*] 
Downy mildew (Peronospora 
spp.)[*] 
Early blight (Alternaria spp.)[*] 
Late blight (Phythopthora spp.)[*] 
Powdery mildew[*] 
Ramularia 
(Ramularia spp.)[*] 
Rust (Puccinia 
spp.)[*] 
White mold (Sclerotinia spp.)[*] 
0.45 - 0.68 lb/acre

Turf/sod (grasses & grasses 
grown for seed)[*]: Bentgrass, 
Bermudagrass, Bluegrass, Carpet 
grass, Centipedegrass, Fescue, 
Kikuyu, Paspalum, Ryegrass, Sod, 
St. Augustine Grass, Zoysia Grass 
[*Not Registered for Use By 
California] 
Anthracnose (Colletotrichum spp.)[*] 
Brown patch (Rhizoctonia spp.)[*] 
Cercospora (Cercospora spp.)[*] 
Dollar spot (Clarireedia jacksonii)[*] 
Fusarium (Fusarium spp.)[*] 
Gray leafspot (Pyricularia spp.)[*] 
Helminthosporium Leaf Spot 
(Helminthosporium spp.)[*] 
0.25 – 0.5 lbs/acre 
Stone Fruits[*]: Apricot; 
Apricot, Japanese; Capulin; 
Cherry, black; Cherry, Nanking; 
Cherry, sweet; Cherry, tart; 
Jujube, Chinese; Nectarine; 
Peach; Plum; Plum, American; 
Plum, beach; Plum, Canada; 
Plum, cherry; Plum, Chickasaw; 
Plum, Damson; Plum, Japanese; 
Plum, Klamath; Plum, prune; 
Plumcot; Sloe; cultivars, 
varieties, and/or hybrids of these 
[*Not Registered for Use By 
California] 
Alternaria 
(Alternaria spp.)[*] 
Anthracnose (Colletotrichum 
spp.)[*] 
Botrytis (Botrytis spp.)[*] 
Brown rot/ Blossom blight 
(Monilinia spp.)[*] 
Phytophthora (Phytophthora 
spp.)[*] 
Powdery mildew[*] 
Scab (Cladosporium spp.)[*] 
 
0.23 - 0.91 lb/acre 
Tree Nut Crops Group and 
Subgroup[*]: African nut- tree; 
Almond; Beechnut; Brazil nut; 
Brazilian pine; Bunya; Bur oak; 
Butternut; Cajou nut; Candlenut; 
Cashew; Chestnut; Chinquapin; 
Coconut; Dika nut; Ginkgo; 
Guianan chestnut; Hazelnut; 
Heartnut; Hickory nut; Japanese 
horse- chestnut; Macadamia 
nut; Mongongo nut; Monkey-pot; 
Monkey puzzle nut; Okari nut; 
Pachira nut; Peach palm nut; 
Pecan; Pequi; Pili nut; Pine nut; 
Pistachio; Sapucaia nut; 
Tropical almond; Walnut, black; 
Walnut, English; Yellowhorn; 
cultivars, varieties, 
and/or hybrids of these 
[*Not Registered for Use By 
California] 
Alternaria (Alternaria spp.)[*] 
Anthracnose (Colletotrichum 
spp.)[*] 
Botrytis (Botrytis spp.)[*] 
Brown rot/ Blossom blight 
(Monilinia spp.)[*] 
Powdery mildew[*] 
Scab (Venturia spp., 
Fusicladium spp.)[*] 
0.23 - 0.91 lb/acre 
Tropical and Subtropical 
Fruit, Edible Peel Group and 
Subgroup[*]: Banana; Mango; 
Papaya; Avocado; 
Pineapple; Kiwi; Cultivars, 
varieties and/or hybrids of 
these. 
[*Not Registered for Use By 
California] 
Alternaria (Alternaria spp.)[*] 
Anthracnose (Colletotrichum 
spp.)[*] 
Black sigatoka 
(Mycosphaerella spp.)[*] 
Botrytis (Botrytis spp.)[*] 
Cercospora (Cercospora 
spp.)[*] 
Powdery mildew[*] 
0.45 - 0.91 lb/acre

7.0 STORAGE AND DISPOSAL 
STORAGE AND DISPOSAL 
Do not contaminate water, food, or feed by storage or disposal. 
Pesticide Storage: Store in original container in a cool, dry place. Prevent exposure to 
moisture. Keep container tightly closed and out of reach of children. Avoid contamination 
with other pesticides or fertilizers. 
Pesticide Disposal: To avoid wastes, use all material in this container by application 
according to label directions. If wastes cannot be avoided, offer remaining product to a waste 
disposal facility or pesticide disposal program (often such programs are run by state or local 
governments or by industry). 
Container Handling: 
(For pails with liner) Nonrefillable container. Do not reuse or refill this container. Offer for 
recycling, if available, or dispose of in a sanitary landfill or by incineration. If pail is 
contaminated, triple rinse promptly after emptying. Triple rinse as follows: Empty the 
remaining contents into application equipment or mix tank. Fill the container ¼ full of water 
and recap. Shake for 10 seconds. Pour rinsate into application equipment or a mix tank or 
store for later use or disposal. Drain for 10 seconds after the flow begins to drip. Repeat this 
procedure two more times. 
(For plastic bags) Nonrefillable container. Do not reuse or refill this container. Completely 
empty bag into application equipment by shaking and tapping sides and bottom to loosen 
clinging particles. Then offer for recycling, if available, or dispose of empty bag in a sanitary 
landfill or by incineration. Do not burn unless allowed by state and local ordinances. If 
burned, stay out of smoke.

8.0 CONDITIONS OF SALE AND LIMITATION OF WARRANTY 
AND LIABILITY 
NOTICE: Read the entire Directions for Use and Conditions of Sale and Limitation of 
Warranty and Liability before buying or using this product. If the terms are not 
acceptable, return the product at once, unopened, and the purchase price will be 
refunded. 
 
The Directions for Use of this product must be followed carefully. It is impossible to eliminate 
all risks inherently associated with the use of this product. Crop injury, ineffectiveness or other 
unintended consequences may result because of such factors as manner of use or 
application, weather or crop conditions, presence of other materials or other influencing 
factors in the use of the product, which are beyond the control of SYNGENTA CROP 
PROTECTION, LLC or Seller. To the extent permitted by applicable law, Buyer and User 
agree to hold SYNGENTA and Seller harmless for any claims relating to such factors. 
 
SYNGENTA warrants that this product conforms to the chemical description on the label and 
is reasonably fit for the purposes stated in the Directions for Use, when used in accordance 
with directions under normal use conditions. To the extent permitted by applicable law: (1) this 
warranty does not extend to the use of the product contrary to label instructions or under 
conditions not reasonably foreseeable to or beyond the control of Seller or SYNGENTA, and 
(2) Buyer and User assume the risk of any such use. TO THE EXTENT PERMITTED BY 
APPLICABLE LAW, SYNGENTA MAKES NO WARRANTIES OF MERCHANTABILITY OR 
OF FITNESS FOR A PARTICULAR PURPOSE NOR ANY OTHER EXPRESS OR IMPLIED 
WARRANTY EXCEPT AS WARRANTED BY THIS LABEL. 
 
To the extent permitted by applicable law, in no event shall SYNGENTA be liable for any 
incidental, consequential or special damages resulting from the use or handling of this 
product. TO THE EXTENT PERMITTED BY APPLICABLE LAW, THE EXCLUSIVE 
REMEDY OF THE USER OR BUYER, AND THE EXCLUSIVE LIABILITY OF SYNGENTA 
AND SELLER FOR ANY AND ALL CLAIMS, LOSSES, INJURIES OR DAMAGES 
(INCLUDING CLAIMS BASED ON BREACH OF WARRANTY, CONTRACT, NEGLIGENCE, 
TORT, STRICT LIABILITY OR OTHERWISE) RESULTING FROM THE USE OR HANDLING 
OF THIS PRODUCT, SHALL BE THE RETURN OF THE PURCHASE PRICE OF THE 
PRODUCT OR, AT THE ELECTION OF SYNGENTA OR SELLER, THE REPLACEMENT 
OF THE PRODUCT. 
SYNGENTA and Seller offer this product, and Buyer and User accept it, subject to the 
foregoing Conditions of Sale and Limitation of Warranty and of Liability, which may not be 
modified except by written agreement signed by a duly authorized representative of 
SYNGENTA.

Stroveq®, the ALLIANCE FRAME 
the Syngenta Logo and the PURPOSE ICON 
are Trademarks of a Syngenta Group Company 
 
 
©20XX Syngenta 
 
For non-emergency (e.g. current product information), call 
Syngenta Crop Protection at 1-866-796-4368. 
 
 
Manufactured for: 
Syngenta Crop Protection, LLC 
P.O. Box 18300 
Greensboro, North Carolina 27419-8300 
 
 
Stroveq XXXX NEW APR2025-jab-4/22/25 
000100-0XXXX.20250423.STROVEQ.NEW.0425.pdf