crop-chem-docs/corpus/epa_ppls/228-238.md

# 1D AMINE

- EPA Reg No: **228-238**
- Registrant: NUFARM AMERICAS, INC.
- Signal word: Caution
- Active ingredients: 2,4-D, dimethylamine salt (11.84%)
- Label accepted: 2008-06-17
- Source PDF: https://www3.epa.gov/pesticides/chem_search/ppls/000228-00238-20080617.pdf

---
". 
U.S. ENVIRONMENTAL PROTECTION 
AGENCY 
Office of Pesticide Programs 
Registration Division (7505P) 
Ariel Rios Building 
1200 Pennsylvania Ave., NW 
Washington, D.C. 20460 
NOTICE OF PESTICIDE: 
_ Registration 
~ Reregistration 
(under FIFRA, as amended) 
Name and Address of Registrant (include ZIP Code): 
Nufarm Americas, Inc. 
150 Harvester Drive, Suite 200 
Burr Ridge, IL 60527 
EPA Reg. Number: Date of Issuance: 
228-238 
1 7 JUN 2008 
Tenn ofIssuance: 
Name of Pesticide Product: 
IDAmine 
Np~e: Changes ilfiab.:~lrrtg,differihg in;· s4b~Jap~~from: th4f~c6epfed H(c.9im~~ti'oh With thIs: 
registration mu~t,be ~ti&initted to ~d accep!e~'by ~e Regi"s~~tiptl');)~v.j~·~on ;prior tQ ~se of the label 
in commerce. Iii' any. corresRPpdence' or:IAhis~product always .referto.:tlr~"above EPA registtatiqn 
~umber. " ." .... '.'.' . ,., '., .':~.. "r J'-. ,'. .. .. 
On the basis of information furnished by the registrant, the above named pesticide is hereby 
registered/reregistered under the Federal Insecticide, Fungicide and Rodenticide Act. Registration is 
in no way to be construed as an endorsement or recommendation of this product by the Agency. In 
order to protect health and the environment, the Administrator, on his motion, may at any time 
suspend or cancel the registration of a pesticide in accordance with the Act. The acceptance of any 
name in connection with the registration of a product under this Act is not to be construed as giving 
the registrant a right to exclusive use of the name or to its use if it has been covered by others. 
This product is reregistered in accordance with FIFRA sec. 4(g)(2)(C) provided that you: 
1. Submit and/or cite all data required for registration/reregistration review of your product when 
the Agency requires all registrants of similar products to submit data. 
2. Per the acute toxicity review, the Hazards to Humans and Domestic Animals must be revised to 
read: "CAUTION Harmful if swallowed. Causes moderate eye irritation. Avoid contact with eyes, 
skin or clothing." 
Signature of Approving Official: 
Joanne I. Miller 
Product Manage 
Herbicide Branch 
Registration Division (7505P) 
EPA Form 8570-6 
Date: 
1 '1 JUN. 2008

( 
" 
r 
page 2 
EPA Reg. No. 228-238 
3. Per the acute toxicity review and the RED, the PPE section must be revised to read: 
"Some materials that are chemical-resistant to this product are made of any waterproof material. 
If you want more options, follow the instructions for category A on an EPA chemical-resistance 
category selection chart. All mixers, loaders, applicators, flaggers, and other handlers must wear: 
-Long sleeved shirt and long pants, -Shoes and socks, -Chemical-resistant gloves (except for 
pilots), -Chemical-resistant apron when mixing or loading, cleaning up spills or equipment, or 
otherwise exposed to the concentrate. See engineering controls for additional requirements." 
4. The mechanical transfer engineering control text appearing on the label is no longer needed 
and may be deleted. 
5. The text "except as noted on appropriate labels" should be removed from the second sentence 
of the Environmental Hazard statements. 
6. Reference to chemigation in the first sentence of the Spray Drift Management section must be 
deleted because this label states "Do not apply this product through any type of irrigation 
system." 
7. Correct the text under the heading General Precautions and Restrictions to read "Do not 
contaminate water used for irrigation." 
8. Per the RED, the following rate restrictions must be added to the Grasses (Established 
Pastures and Rangeland) directions for use: "For susceptible annual and biennial broadleafweeds 
- Do not apply more than 1.0 lbs ae per acre per application. For moderately susceptible biennial 
and perennial broadleaf weeds, difficult to control weeds and woody plants - Do not apply more 
than 2.0 lbs ae per acre per application." 
9. For ornamental turf: The annual application rate of up to 4 gallons of product per acre per year 
(or 3.4lbs ae per acre per year) exceeds the allowable maximum application rate of3.0 lbs ae per 
acre per year. The maximum single application rate of up to 2 gallons of product per acre (or 1.7 
lbs ae per acre per application) exceeds the allowable rate of 1.5 lb ae per acre per application. 
The label must be revised. 
10. For floating and emergent weeds: The maximum application rate of 5 gallons of product per 
surface acre per application (4.25 lbs ae per surface acre) exceeds the allowable maximum 
application rate of 4.0 lbs ae per surface acre per application. The label must be revised.

( 
page 3 
EPA Reg. No. 228-238 
11. To the label add "Use of this product in certain portions of California, Oregon, and 
Washington is subject to the January 22,2004 Order for injunctive relief in Washington Toxics 
Coalition, et al. v. EPA, C0132C, (w.n. WA). For further information, please refer to EPA Web 
Site: http://www.epa.gov/espp.'' 
Submit one copy of the revised final printed label for the record. 
If these conditions are not complied with, the registration will be subject to cancellation in 
accordance with FIFRA sec. 6(e). Your release for shipment of the product constitutes 
acceptance of these conditions. 
A stamped copy of the label is enclosed for your records. 
If you have any questions please call Erik Kraft at 703-308-9358 or email atKraft.Erik@epa.gov.

( 
10 AMINE 
A SELECTIVE WEED KILLER 
Lt \~ 'b 
ACCEPTED 
with COMMENTS 
In EPA Letter Dated: 
1 7 JUN 2008 
Under the Federal Insecticide, 
Fungicide, and Rodenticide Act 
as amended, for the pesticide 
registered under EPA Reg. No. 
FOR CONTROL OF MANY BROADLEAFWEEDS IN BOTH NON-CROP AND CERTAIN 
CROP AREAS, LAWNS, PONDS, DRAINAGE DITCHBANKS, PASTURES AND 
RANGELANDS. ALSO FOR CONTROL OF TREES BY INJECTION. 
ACTIVE INGREDIENT: 
Dimethylamine Salt of 2,4-Dichlorophenoxyacetic Acid* . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 11.84% 
OTHER INGREDIENTS: ............................................................................. 88.16% 
TOTAL: .. . . . . . . . . . . . . . . . . . . . . . . . .. 100.0% 
Isomer Specific AOAC Method, Equivalent to: 
*2,4-Dichlorophenoxyacetic Acid ..............•....•......................•...•........• 9.83%, 0.85Ibs/gal. 
KEEP OUT OF REACH OF CHILDREN 
CAUTION - PRECAUCION 
Si usted no entiende la etiqueta, busque a alguien para que se la explique a usted en detalle. 
(If you do not understand the label, find someone to explain it to you in detail.) 
SEE INSIDE BOOKLET FOR FIRST AID AND ADDITIONAL PRECAUTIONARY STATEMENTS 
For Chemical Spill, Leak, Fire, or Exposure, Call CHEMTREC (800) 424-9300 
For Medical Emergencies Only, Call (Sn) 325-1840 
NOTE: Spanish language is optional 
EPA REG. NO. 228-238 
EPA EST. NO. 228-IL-1 
MANUFACTURED BY 
NUFARM AMERICAS INC. 
150 HARVESTER DRIVE 
BURR RIDGE, IL 60527 Mufarm 
NET CONTENTS GALS. 
00022B-0023B.200B0211.EPA.24d.Pending 
, I , I I 
, 
( • I I 
,.j , ( \ 
I I {I 
,

( 
\ ( 
PRECAUTIONARY STATEMENTS 
HAZARDS TO HUMANS AND DOMESTIC ANIMALS 
CAUTION - PRECAUCION 
Causes moderate eye irritation. Avoid contact with eyes, skin or clothing. Wash thoroughly with .soap and water after handling and 
before eating, drinking, chewing gum, using tobacco or using the toilet. 
PERSONAL PROTECTIVE EQUIPMENT (PPE) 
Some materials that are chemical-resistant to this product are listed below. If you want more options, follow the instructions for category 
A on an EPA chemical-resistance category selection chart. 
All mixers, loaders, applicators, flaggers, and other handlers must wear: 
• long-sleeved shirt and long pants, 
• shoes and socks, plus 
• chemical resistant gloves, when applying with any handheld nozzle or equipment, mixing or loading, cleaning up spills or equipment, 
or otherwise exposed to the concentrate. . 
• chemical resistant apron when mixing or loading, cleaning up spills or equipment, or otherwise exposed to the concentrate. 
• protective eyewear 
See engineering controls for additional requirements. 
Follow manufacturer's instructions for cleaning/maintaining PPE. If no such instructions for washables exist, use detergent and hot water. 
Keep and wash PPE separately from other laundry. 
Engineering Control Statements: 
If this container is over one gallon and less than five gallons, then persons engaged in open pouring of this product must also wear 
coveralls or a chemical resistant apron. If this container is five gallons or more in capacity, do not open pour product from this container. 
A mechanical system (such as a probe and pump or spigot) must be used for transferring the contents of this container. If the contents 
of a non-refillable pesticide container are emptied, the probe must be rinsed before removal. If the mechanical system is used in a 
manner that meets the requirements listed in the Worker Protection Standard (WPS) for agricultural pesticides [40 CFR 170.240(d)(4-
6], the handler PPE requirements may be reduced or modified as specified in the WPS. 
When handlers use closed systems, enclosed cabs, or aircraft in a manner that meets the requirements listed in the Worker Protection 
Standard (WPS) for agricultural pesticides [40 CFR 170.240(d) (4-6)], the handler PPE (personal protective equipment) requirements 
may be reduced or modified as specified in the WPS. Pilots must use an enclosed cockpit that meets the requirements listed in the WPS 
for agricultural pesticides [40 CFR 170.240(d)(6)]. . 
USER SAFETY RECOMMENDATIONS 
Users Should: 
• Wash hands before eating, drinking, chewing gum, using tobacco or using the toilet. 
• Remove clothing/PPE immediately if pesticide gets inside. Then wash thoroughly and put on clean clothing. If pestiCide gets on 
skin, wash immediately with soap and water. . 
• Remove PPE immediately after handling this product. Wash the outside of gloves before removing. As soari as possible, wash 
thoroughly and change into clean clothing. 
IF IN EYES 
IF SWALLOWED 
IFON SKIN 
OR CLOTHING 
FIRST AID 
• Hold eye open and rinse slowly and gently with water for 15 to 20 minutes. 
• Remove contact lenses, if present, after the first 5 minutes, then continue rinsing eye. 
• Call a poison control center or doctor for treatment advice. 
• Call poison control center or doctor immediately for treatment advice. 
• Have person sip a glass of water if able to swallow. 
• Do not induce vomiting unless told to do so by the poison control center or doctor. 
• Do not give anything by mouth to an unconscious person. 
• Take off contaminated clothing. 
• Rinse skin immediately with plenty of water for 15 to 20 minutes. 
• Call a poison control center or doctor for treatment advice. 
r-----------------------------~--------------------------------------------------------------------------------------------------------------------~:~'-----~ HOT LINE NUMBER ' , ' , 
Have the product container or label with you when calling a poison control center or doctor, or going for t~eatnert. 
You may also contact 1-877-325-1840 for emergency medical treatment information. " L...- ____ ...,.- ______________________ --"-" ."'''' '" _ --:.,'"C~ 
2

( ( 
ENVIRONMENTAL HAZARDS 
For Terrestial Uses: 
This pesticide may be toxic to fish and aquatic invertebrates. Do not apply directly to water, to areas where surface water is present, 
or to intertidal areas below the mean high water mark except as noted on appropriate labels. Drift and runoff may be hazardous to 
aquatic organisms in water adjacent to treated areas. Do not contaminate water when disposing of eqUipment wash waters or rinsate. 
This chemical has properties and characteristics associated with chemicals detected in groundwater. The use of this chemical in areas 
where soils are permeable, particularly where the water table is shallow, may result in groundwater contamination. Application around 
a cistern or well may result in contamination of drinking water or groundwater. 
For Aquatic Uses: 
Fish breathe dissolved oxygen in the water and decaying weeds also use oxygen. When treating continuous, dense weed masses, it 
may be appropriate to treat only part of the infestation at a time. For example, apply the product in lanes separated by untreated strips 
that can be treated after vegetation in treated lanes has disintegrated. During the growing season, weeds decompose in a 2 to 3 week 
period following treatment. Begin treatment along the shore and proceed outwards in bands to allow fish to move into untreated areas. 
Waters having limited and less dense weed infestations may not require partial treatments. 
DIRECTIONS FOR USE 
It is a violation of Federal law to use this product in a manner inconsistent with its labeling. 
READ ENTIRE LABEL BEFORE USING THIS PRODUCT. USE STRICTLY IN ACCORDANCE WITH LABEL PRECAUTIONARY 
STATEMENTS AND DIRECTIONS. 
Do not apply this product in a way that will contact workers or other persons, either directly or through drift. Only protected handlers 
may be in the area during application. For any requirements specific to your State or Tribe, consult the agency responsible for pesticide 
regulation. 
AGRICULTURAL USE REQUIREMENTS 
Use this product only in accordance with its labeling and with the Worker Protection Standard, 40 CFR part 170. This Standard 
contains requirements for the protection of agricultural workers on farms, forests, nurseries, and greenhouses, and handlers of 
agricultural pesticides. It contains requirements for training, decontamination, notification, and emerge'ncy assistance. It also 
contains specific instructions and exceptions pertaining to the statements on this label about personal protective equipment (PPE) 
and restricted-entry interval. The requirements in this box only apply to uses of this product that are covered by the Worker 
Protection Standard. 
Do not enter or allow worker entry into treated areas during the restricted-entry interval (REI) of 48 hours. 
PPE required for early entry to treated areas that is permitted under the Worker Protection Standard and that involves contact with 
anything that has been treated, such as plants, soil, or water is: coveralls, chemical-resistant gloves made of any waterproof 
material, shoes plus socks and protective eyewear. 
NON-AGRICULTURAL USE REQUIREMENTS 
The requirements in this box apply to uses of this product that are NOT within the scope of the Worker Protection Standard for 
agricultural pesticides (40 CFR part 170). The WPS applies when this product is used to produce agricultural plants on farms, 
forests, nurseries, or greenhouses. 
Do not enter or allow people (or pets) to enter the treated area until sprays have dried. 
GENERAL PRECAUTIONS AND RESTRICTIONS 
Do not apply this product through any type of irrigation system. Do not contaminate water used for irritation or domestiC purposes. 
Excessive amounts of this product in soil may temporarily inhibit seed germination and plant growth. Do not use the same spray 
equipment for applying other materials to 2,4-0 susceptible crops as injury may result. It is best to use a separate sprayer for 
application of insecticides and fungicides. 
SPRAY DRIFT MANAGEMENT 
A variety of factors including weather conditions (e.g., wind direction, wind speed, temperature, relative humidity) and method of 
application (e.g., ground, aerial, airblast, chemigation) can influence pesticide drift.The applicator must evaluate all factors and make 
appropriate adjustments when applying this product. 
Droplet Size 
When applying sprays that contain 2,4-0 as the sole active ingredient, or when applying sprays that contain 2,4-0 mixed with active 
ingredients that require a Coarse or coarser spray, apply only as a Coarse or coarser spray (ASAE standard 572) or a volume mean 
diameter of 385 microns or greater for spinning atomizer nozzles. 
When applying sprays that contain 2,4-0 mixed with other active ingredients that require a Medium or more fine spray, apply only as 
a Medium or coarser spray (ASAE standard 572) or a volume mean diameter of 300 microns or greater for spinning atomizer nozzles. 
Wind Speed 
Do not apply at wind speeds greater than 15 mph. Only apply this product,if the wind direction favors on-target deposition and there 
are not sensitive areas (including, but not limited to, residential areas, bodies of water, known habitat for nontarget species, nontarget 
crops) within 250 feet downwind. If applying a Medium spray, leave one swath unsprayed at the downwind edge of the treated field. 
3

( 
Temperature Inversions 
If applying at wind speeds less than 3 mph, the applicator must determine if: a) conditions of temperature inversion exist, or b) stable 
atmospheric conditions exist at or below nozzle height. Do not make applications into areas of temperature inversions or stable 
atmospheric conditions. . 
Susceptible Plants 
Do not apply under circumstances where spray drift may occur to food, forage, or other plantings that might be damaged or crops 
thereof rendered unfit for sale, use or consumption. Susceptible crops include, but are not limited to, cotton, okra, flowers, grapes (in 
growing stage), fruit trees (foliage), soybeans (vegetative stage), ornamentals, sunflowers, tomatoes, beans, and other vegetables, or 
tobacco. Small amounts of spray drift that might not be visible may injure susceptible broadleaf plants. 
Other State and Local ReqUirements 
Applicators must follow all state and local pesticide drift requirements regarding application of 2,4-0 herbicides. Where states have 
more stringent regulations, they must be observed. 
Equipment 
All aerial and ground application equipment must be properly maintained and calibrated using appropriate carriers or surrogates. 
Additional requirements for aerial applications: 
The boom length must not exceed 75% of the wingspan or 90% of ·the rotor blade diameter. 
Release spray at the lowest height consistent with efficacy and flight safety. Do not release spray at a height greater than 10 feet 
above the crop canopy unless a greater height is required for aircraft safety. This requirement does not apply to forestry or rights-of­
way applications. 
When applications are made with a crosswind, the swath will be displaced downwind. The applicator must compensate for this by 
adjusting the path of the aircraft upwind. 
Additional requirements for ground boom applications: 
Do not apply with a nozzle height greater than 4 feet above the crop canopy. 
WEEDS CONTROLLED 
This product will kill or control the following weeds in addition to many other noxious plants susceptible to 2,4-0. 
Alder Dandelion Musk thistle Spatterdock 
Americanlotus Dock Mustard Stinging nettie 
Arrowhead Dogbane Nettle Stinkweed 
Artichoke Duckweed Nutgrass Sumac 
Aster Elderberry Orange hawkweed Sunflower 
Austrian fieldcress Fleabane (daisy) Parrotfeather Sweet clover 
Beggartick Flixweed Parsnip TalWeed 
Biden Rorida pusiey Pennycress Thistles 
Bindweed Frenchweed Pennywort Toadflax 
BittelWeeds Galinsoga Peppergrass Tumbleweed 
Bitter winter cress Goatsbeard Pepperweed Velvetleaf 
Blessed thistle Goldenrod Pigweed Vervain 
Blue lettuce Ground ivy Plantains Vetch 
Box elder Gumweed Poison hemlock Virginia creeper 
Broomweed Healall Poison ivy Water hyacinth 
Buckhorn Hemp Pokeweed Water lily 
Bull thisHe Henbit Poorjoe Water plantain 
Bulrush Hoary cress Povertyweed Water primrose 
Burdock Honeysuckle Prickly lettuce Water shield 
Bur ragweed Horsetail Primrose Wild carrot 
Buttercup Indigo Puncturevine Wild garlic 
Canada thistle Indiana mallow Purslane Wild lettuce 
Carpetweed Ironweed Ragweed Wild onion 
Catnip Jewelweed Rush Wild radish 
Chickweed Jimsonweed Russian thistle Wild rape 
Chicory Kochia Sagebrush Wild strawberry 
Cockle Knotweed SI. Johnswort Wild sweet potato 
Cocklebur Lambsquarter Shepherdspurse Willow 
Coffee bean Locoweed Sicklepod Witchweed 
Coffeeweed Lupine Smartweed Wormseed 
Common sowthistle Mallow Sneezeweed Yellow rocket 
Creeping jenny Marshelder Southern wild rose 
Croton Mexican weed Sowthistle 
Curly indigo . Morningglory Spanishneedle 
4

( ( 
Generally the lower dosages given will be satisfactory for young, succulent growth of sensitive weed species. For less sensitive 
species and under conditions where control is more difficult, the higher dosages will be needed. Apply this product during warm 
weather when weeds are young and growing actively. Use enough spray volume for uniform coverage by ground or air application. If 
only bands or rows are treated, leaving middles unsprayed, the dosage per crop per acre is reduced proportionately. Do not apply 
when temperature exceeds 90°F. -
MIXING INSTRUCTIONS 
MIX this product only with water. Add about half the water to the mixing tank, then add this product with agitation, and finally the rest 
of the water with continuing agitation. Note: Adding oil, wetting agent, or other surfactant to the spray may increase effectiveness on 
weeds but also may reduce selectivity to crops resulting in crop damage. 
CORN 
(Field and Sweet) 
Preemergence (For annual grasses and broad leaf weeds) - Apply to soil anytime after planting but before corn emerges. Do not use 
on light sandy soil, or where soil moisture is low. Use 1 gallon in 15 to 30 gallons of water per acre. Maximum rate per application is 
1 gallon per acre, limited to one preplant or preemergence application per crop cycle. 
Emergence - Apply 2 quarts in 15 to 30 gallons of water per acre just as corn plants are breaking ground. 
Postemergence - (For broadleaf weeds) - Apply 1 to 2 quarts in 8 to 15 gallons of water per acre, when most weeds have germinated. 
Maximum rate per application is 2.5 quarts per acre, limited to one postemergence application per crop cycle. Spray after corn 
emerges and until 8 inches tall. Use low rates on inbreds. Corn is susceptible to injury shortly after emergence and after unfolding of 
leaves. Do not spray during this period nor after first tassels appear. When corn is over 8 inches tall, use drop nozzle to keep spray 
off corn fOliage. Spray must strike tops of weeds but should not drench corn plants. Do not apply from tasseling to dough stage. Injury 
to corn is most likely to occur if this product is applied when corn is growing rapidly under high temperatures and high soil moisture 
conditions. In such conditions, use the low rate. For resistant weeds, use up to 2.5 quarts per acre though corn injury may result. Do 
not use higher rates unless possible crop injury will be acceptable. After application, delay cultivation for 8 to 10 days to allow the corn 
to overcome any temporary brittleness. 
Preharvest (Field): After the hard dough or denting stage, apply by air or ground equipment to suppress perennial weeds, decrease 
weedseed production, and control tall weeds such as Bindweed, Cocklebur, Dogbane, Jimsonweed, Ragweed, Sunflower, Velvetleaf, 
and vines that interfere with harvesting. Use 0.5 to 1 gallon in 30 to 50 gallons of water per acre. Maximum rate per application is 1.75 
gallons per acre, limited to one preharvest application per crop cycle. -
Limitations for Use on Field Corn: 
• Do not use treated crop as fodder for 7 days following application. 
• The preharvest interval (PHI) is 7 days. 
• Maximum of 3.5 gallons per acre per crop cycle. 
Limitations for Use on Sweet Corn: 
• Do not use treated crop as fodder for 7 days following application. 
• The preharvest interval (PHI) is 45 days. 
• Minimum of 21 days between applications. 
• Maximum of 1.75 gallons per acre per crop cycle. 
WITH LIQUID NITROGEN SOLUTIONS: For late season control of your Smartweed, Cocklebur, Annual morningglory and other 
annual broadleaf weeds less than 1 inch high. Field should be as clean as possible and corn 20 to 30 inches tall. Apply 1/2 gallon 
with 80 to 120 pounds Nitrogen per acre; the spray must be prepared by first adding the required amount of liquid Nitrogen solution 
to spray tank. Next dilute 2 quarts of this product with 2 quarts clean water for each acre to be treated with one tankful. Start the tank 
agitator and (slowly) add the diluted 2,4-0 solution. Spray immediately, maintaining continuous agitation until spray tank is empty. 
Direct the spray to lower 3 to 4 inches of corn stalk. Use spray equipment designated to handle corrosive liquid nitrogen solutions. 
After spraying, remove any remaining solution and rinse rig thoroughly with water. Mix only one tank at a time. Do not spray during or 
immediately following cold weather. 
SORGHUM 
Postemergence - Apply 2-213 to 4 pints in 6 to 10 gallons of water per acre when sorghum is 6 to 8 inches tall. Use 4 pints when 
sorghum is 8 to 15 inches tall. Treat only after the sorghum is 6 inches high and preferably before it is 15 inches high. Do not treat 
during the boot, tasseling, or early dough stages. Reduce spray drift by keeping the boom and spray nozzle as low as possible. If crop 
is taller than 8 inches, use drop nozzle to keep the spray off the leaves. Temporary spray injury can be expected under conditions of 
high soil moisture and high air temperatures. If it is necessary to apply this product under these conditions, use no more than 2-2/3 
pints per acre. Maximum rate per application is 9 pints per acre, limited to one application per crop cycle. 
Limitations forUse on Sorghum: _ 
• Do not permit meat or dairy animals to consume treated crop as fodder or forage for 30 days following application. 
• The preharvest interval (PHI) is 30 days. 
NOTE: 
Corn & Sorghum Hybrids vary in tolerance to 2,4-0. Some are easily injured. Spray only varieties known to be tolerant to 2,4-0. 
Consult the seed company or your Agricultural Experiment Station or Extension Service weed specialist for this information. 
5

( 
BARLEY, WHEAT, OATS AND RYE 
Spring Postemergence - In Spring grown grains, spray after grain begins tillering and before the boot stage (usually 4 to 8 inches 
tall) and weeds are small. Apply 1 to 2 quarts of this product in 5 to 10 gallons of water per acre. Oats are more sensitive to 2,4-0 
than other grains and should be sprayed in the Spring when well established and tillered and before jointing after crop has reached 
the dough stage. In Winter grains, use 2 to 4 quarts of this product to control large weeds that will interfere with harvest or to suppress 
perennial weeds. The maxirnum rate per application is 6 quarts per acre per application, limited to one postemergence application 
per crop cycle. 
Preharvest treatment can be applied when the grain is in the dough stage. Best results will be obtained when soil moisture is adequate 
for plant growth and weeds are growing well. Maximum rate per application is 2.5 quarts per acre per application, limited to one 
preharvest application per crop cycle. 
Limitations for Use on Barley, Wheat, Oats and Rye: 
• Do not permit dairy animals or meat animals being finished for slaughter to forage or graze treated grain fields within 2 weeks after 
treatment. Do not feed treated straw to livestock. 
• The preharvest interval (PHI) is 14 days. 
• Limited to 8.25 quarts per acre per crop cycle. 
SUGARCANE 
Preemergence - Use 2 gallons in 15 to 20 gallons of water per acre as a blanket spray through layby, to aid in control of Johnsongrass 
seedlings and susceptible broadleaf weeds. The maximum rate per application is 2.5 gallons per acre, limited to one preemergence 
application per crop cycle. 
Postemergence - Use 0.75 to 1 gallon in 10 to 30 gallons of water. Apply when cane is 1 to 2 feet tall. The maximum rate per 
application is 2.5 gallons per acre, limited to one postemergence application per crop cycle. 
Limitations Use on Sugarcane: 
• Do not harvest cane prior to crop maturity. 
• Do not apply more than 4.75 gallons per acre per crop cycle. 
RICE 
Use 0.75 to 1.25 gallons of this product in 5 to 10 gallons of water per acre to control Curly indigo and other broadleaf weeds. Apply 
in the late tillering stage of rice development, at the time of first joint development (first to second green ring), usually 6 to 9 weeks 
after emergence. Do not apply after panicle initiation, after rice internodes exceed 1/2 inch at early seeding, early panicle, boot, 
flowering or early heading growth stages. The maximum rate per application is 1.75 gallons, limited to one postemergence application 
per crop cycle. 
Note: Some rice varieties under certain conditions can be injured by 2,4-0. Therefore before spraying, consult local Extension Service 
or University specialist for appropriate rates and timing of 2,4-0 sprays. 
Limitations for Use on Rice: 
• The preharvest interval (PHI) is 60 days. 
• Maximum of 1.75 gallons per acre per crop cycle. 
ON FALLOW LAND 
Use 1 to 2 gallons of this product per acre on annual broadleaf weeds and up to 3 quarts per acre on established perennial species, 
such as Canada thistle and Field bindweed. Apply to weeds actively growing. Plant only labeled crops within 29 days following 
application. The maximum rate per application is 2.5 gallons per acre, limited to 2 applications per year. Allow a minimum of 30 days 
between applications. 
GRASSES 
(Established Pastures and Rangeland) 
In established pastures and rangelands, use 1 to 2 gallons of this product in 15 to 30 gallons of water per acre per application per 
site. Use the light rate on more easily injured grasses. For small areas, use 3 to 4 fluid ounces (6 to 8 Tablespoons) per 1,000 square 
feet; mix 1 to 3 gallons of water and apply uniformly over the area. Apply preferably when weeds are small and growing actively before 
bud stage. Fall or Spring is the best time to treat. Repeated treatments may be needed for less susceptible weeds, but no more than 
2 applications per year. Treatment will kill or injure alfalfa, sweet clover and other legumes. White clover (including Ladino) may be 
injured. by light application but recovers; repeated treatments will kill it. In some areas dichondra, bent, carpet, buffalo, and St. 
Augustine grasses may be injured. Usually colonial bents are more tolerant than creeping types; velvets are most easily injured. Where 
bentgrass predominates, make 1 application of 1/2 gallon per acre at 30 day intervals. Maximum rate per application is 2.5 gallons 
per acre, limited to 2 applications per year. A minimum of 30 days between applications. The preharvest interval (PHI) is 7 days (cut 
forage for hay). 
Note: If grass is to be cut for hay, Agricultural use Requirements for the Worker Protection Standard are applicable. For program lands, 
such as Conservation Reserve Program, consult program rules to determine whether grass or hay may be used. The more restrictive 
requirements of the program rules or this label must be followed. 
6 
I 
I

( 
CONTROL OF SOUTHERN WILD ROSE: On rangeland, apply a maximum of 2.4 gallons of this product per acre per application per 
site. Do not graze dairy animals on treated areas within 7 days of application. 
GRASS SEED CROPS 
Use 0.5 to 2 gallons in 15 to 30 gallons of water per acre in Spring or Fall to control broadleaf weeds in grass being grown for seed. 
Do not apply from early boot to the milk stage. Spray seeding grass only after the five leaf stage, using 3 to 4 pints per acre to control 
small seeding weeds. After the grass is well established higher rates of up to 2 gallons can be used to control hard-ta-kill annual or 
perennial weeds. For best resu"s, do not use on bentgrass unless grass injury can be tolerated. Maximum rate per application is 2.5 
gallons per acre, limited to 2 applications per year. A minimum of 21 days between applications. Do not graze dairy animals nor cut 
forage for hay within 7 days after application. 
ORNAMENTAL TURF 
(Lawn, Golf Courses, Cemeteries, Parks and Other Grass Areas) 
Use 2 gallons (16 fluid ounces) of this product in 15 to 50 gallons (1 to 8 gallons) of water per acre (2,725 square feet). Treat when 
weeds are young and growing well. Do not use on dichondra or other herbaceous ground covers. Do not use on creeping grasses 
such as bent except for spot treatment nor on freshly seeded turf until grass is well established. Reseeding of lawns should be delayed 
following treatment. With Spring application, reseed in the Fall. With Fall application, reseed in Spring. Legumes are usually damaged 
or killed. Thoroughly wet weeds when applying this mixture. Bindweed, Whitetop, Perennial sow thistle, Blue lettuce, 
Bur ragweed, Canada thistle, and other noxious perennials somewhat resistant to 2,4-0 will require repeated treatments to kill. 
Maximum rate per application is 2 gallons per acre per season, limited to 2 applications per year. The maximum seasonal rate is 4 
gallons per acre, excluding spot treatments. 
NON-CROP AREAS 
(Airfields, Rights-of-Way, Fencerows, Roadsides, Vacant Lots, Drainage Ditch-Banks and Similar Places) 
Use 2 to 2.5 gallons (16 to 20 fluid ounces) of this product in 15 to 50 gallons (1 to 8 gallons) of water per acre (2,725 square feet). 
Treat when weeds are young and growing well. Do not use on dichondra or other herbaceous ground covers. Do not use on creeping 
grasses such as bent except for spot treatment nor on freshly seeded turf until grass is well established. Reseeding of lawns should 
be delayed following treatment. With Spring application, reseed in the Fall. With Fall application, reseed in Spring. Legumes are usually 
damaged or killed. Thoroughly wet weeds when applying this mixture. Bindweed, Whitetop, Perennial sow thistle, Blue lettuce, Bur 
ragweed, Canada thistle, and other noxious perennials somewhat resistant to 2,4-0 will require repeated treatments to kill. Maximum 
rate per application is 2.5 gallons per acre per year, limited to 2 applications per year. Minimum of 30 days between applications. 
To control small areas of woody plants, such as Willows, Honeysuckle, Virginia creeper, Alders and others susceptible to 2,4-0, use 
2 to 4 gallons (1 to 2 quarts) in 100 gallons (12.5 gallons) water; spray to thoroughly wet plants when in full leaf. Retreat as necessary 
for control of regrowth and seedlings. In general, it is better to cut tall woody growth and spray suckers when 2 to 4 feet high. Maximum 
rate per application is 4.75 gallons per acre per year, limited to 1 application per year. 
Applications to non-cropland areas are not applicable to treatment of commercial timber or other plants being grown for sale or other 
commercial use, or for commercial seed production, or for research purposes 
CONTROL OF SOUTHERN WILD ROSE: On roadsides and fencerows, use 4 gallons of this product plus 4 to 8 fluid ounces of an 
agricultural surfactant per 100 gallons of water and spray thoroughly as soon as fOliage is well develop.ed. Two or more treatments 
may be required. 
SPOT TREATMENT IN NON-CROP AREAS: To control broadleaf weeds in small areas with a hand sprayer, use 1 pint (4 fluid 
ounces) of this product in 3 gallons (3/4 gallon) of water and spray to thoroughly wet all foliage. 
TREE INJECTIONS 
(Pine Release) 
To control hardwoods, such as Oaks, Hickory, Maple, Pecan, Elm, Sumac, Sweetgum and Hawthorn in forest and other non-crop 
areas, apply undiluted product in a concentrate tree injector calibrated to apply 2 ml per injection. Space injections 2 inches apart, 
edge to edge, completely around the tree and close to the base. The injector bit must penetrate the inner bark. On hard-to-kill speCies 
such as Hickory, Dogwood, Red maple, Blue beech and Ash, make injections 1 to 1.5 inches apart, edge to edge. Treatment may be 
made at any time of the year. For best results, injections should be made during growing season, May 15 to October 15. Limited to 
one injection application per year, maximum of 2 ml of 4.0 Ibs. ae formulation per injection site. 
WEEDS AND BRUSH ON IRRIGATION CANAL DlTCHBANKS 
(Seventeen Western States: Arizona, California, Colorado, Idaho, Kansas, Montana, Nebraska, New Mexico, 
Nevada, North Dakota, Oklahoma, Oregon, South Dakota, Texas, Utah, Washington and Wyoming.) 
For control of annual and perennial broadleaf weeds: Apply 1 to 2 gallons of this product per acre in approximately 30 to 100 
gallons of water per acre. Treat when weeds are young and actively growing before the·bud or early bloom stage. For harder-ta-control 
weeds, a repeat spray after 30 days using the same rates may be needed for maximum results. 
For woody brush and patches of perennial broadleaf weeds: Mix 2.5 gallons of this product in 150 gallons of water. Wet foliage 
thoroughly using about 1 gallon of solution per square rod. 
Maximum rate per application is 2.5 gallons per acre, limited to 2 applications per season. Minimum of 30 days between applications. 
Spot treatment is permitted. Do not allow dairy animals to graze on treated area for at least 7 days after spraying. Water within treated 
banks should not be fished. 
7

( 
SPRAYING INSTRUCTIONS: Apply with low pressure (10 to 40 psi) power spray equipment mounted on truck, tractor or boat. 
Apply while traveling upstream to avoid accidental concentration of chemical into water. Spray when the air is fairly calm; 5 mph or 
less. 
Do not use on small canals with a flow rate less than 10 cubic feet per second (CFS) where water will be used for drinking purposes, 
CFS may be estimated by using the formula below. The approximate velocity needed for the calculation can be determined by 
observing the length of time that it takes a floating object to travel a defined distance. Divide the distance (ft.) by the time (sec.) to 
estimate velocity (ft. per sec.). Repeat 3 times and use the average to calculate CFS. . 
Average Width (ft.) x Average Depth (ft.) x Average Velocity (ft. per sec.) = CFS 
For DitchbankWeeds: Do not allow boom spray to be directed onto water surface and do not spray across stream to opposite bank. 
For Shoreline Weeds: Allow no more than 2 foot overspray into water with an average of less than 1 foot overspray to prevent 
introduction of greater than negligible amounts of chemical into the water. 
AQUATIC WEED CONTROL 
(Surface Application to Floating and Emergent Weeds) 
Aerial Application: Use 2.5 gallons of this product in 5 to 15 gallons of water to cover one surface acre. 
B,oat Application: Use 2.5 gallons of this product in 50 to 100 gallons of water per acre. 
Uniform coverage is essential. Avoid submerging plants after treatment. Application should be made when leaves are fully developed 
above water line and plants are actively growing. 
Treatment of aquatic weeds can result in oxygen loss from decomposition of dead weeds. This loss can cause fish suffocation. 
Therefore, to minimize this hazard, treat 1/3 to 1/2 of the water area in a single operation and wait at least 21 days between 
treatments. Begin treatments along the shore and proceed outwards in bands to allow fish to move into untreated areas. 
The maximum rate per broadcast application is 5 gallons per surface acre, limited to applications is 2 per year. Do not make a 
broadcast application within 21 days of previous broadcast application. Spot treatments are permitted. 
Apply to emergent aquatic weeds in ponds, lakes, reservoirs, marshes, bayous, drainage ditches, non-irrigation canals, rivers, and 
streams that are quiescent or slow moving. . 
Coordination and approval of local and state authorities may be required, either by letter of agreement or issuance of special permits 
for aquatic applications. . 
Water Use 
1. Water for irrigation or sprays: 
A. If treated water is intended to be used only for crops or non-crop areas that are labeled for direct treatment with 2,4-0 such 
as pastures, turf, or cereal grains, the treated water may be used to irrigate and/or mix sprays for these sites at anytime after 
the 2,4-0 aquatic application. 
B. Due to potential phytotoxicity considerations, the following restrictions are applicable: 
If treated water is intended to be used to irrigate or mix sprays for plants grown in commercial nurseries and greenhouses; 
and other plants or crops that are not labeled for direct treatment with 2,4-0, the water must not be used unless one of the 
following restrictions has been observed: 
i. A setback distance from functional water intake(s) of greater than or equal to 600 feet was used for the application, or, 
ii. A waiting period of 7 days from the time of application has elapsed, or, 
iii. An approved assay indicates that the 2,4-0 concentration is 100 ppb (0.1 ppm) or less at the water intake. Wait at 
least 3 days after application before initial sampling at water intake. 
2. Drinking water (potable water): 
A. Consult with appropriate state or local water authorities before applying this product to public waters. State or local agencies 
may require permits. The potable water use restrictions on this label are to ensure that consumption of water by the public 
is allowed only when the concentration of 2,4-0 in the water is less than the MCl (Maximum Contaminant Level) of 70 ppb. 
Applicators should consider the unique characteristics of the treated waters to assure that 2,4-0 concentrations in potable 
water do not exceed 70 ppb at the time of consumption. 
B. For floating and emergent weed applications, the drinking water setback distance from functioning potable water intakes is 
greater than or equal to 600 feet. 
C. If no setback distance of greater than or equal to 600 feet is used for application, applicators or the authorizing organization 
must provide a drinking water notification prior to a 2,4-0 application to the party responsible for public water supply or to 
individual private water uses. Notification to the party responsible for a public water supply or to individual private water users 
must be done in a manner to assure that the party is aware of the water use restrictions when this product is applied to 
potable water. 
The following is an example of a notification via posting, but other methods of notification which convey the above restrictions 
may be used and may be required in some cases under state or local law or as a condition of a permit. 
8

( ( 
Example: 
Posting notification should be located every 250 feet including the shoreline of the treated area and up to 250 feet of 
shoreline past the application site to include immediate public access points. Posting must include the day and time of 
application. Posting may be removed if analysis of a sample collected at the intake 3 or more days following application 
shows that the concentration in the water is less than 70 ppb (100 ppb for irrigation or sprays), or after 7 days following 
application, whichever occurs first. 
Text of notification: Wait 7 days before diverting functioning surface water intakes from the treated aquatic site to use as 
drinking water, irrigation, or sprays, unless water at functioning drinking water intakes is tested at least 3 days after 
application and is demonstrated by assay to contain not more than 70 ppb 2,4-D (100 ppb for irrigation or sprays). 
Application Date: __ Time: __ _ 
D. Following each application of this product, treated water must not be used for drinking water unless one of the following 
restrictions has been observed: 
i. A setback distance from functional water intake(s) of greater than or equal to 600 ft. was used for the appiication, or, 
ii. A waiting period of at least 7 days from the time of application has elapsed, or, 
iii. An approved assay indicates that the 2,4-D concentration is 70 ppb (0.07 ppm) or less at the water intake. Sampling 
for drinking water analysis should occur no sooner than 3 days aft~r 2,4-D application. Analysis of samples must be 
completed by a laboratory that is certified under the Safe Drinking Water Act to perform drinking water analySis using 
a currently approved version of analytical Method Number 515,555, other methods for 2,4- D as may be listed in Title 
40 CFR, Part 141.24, or Method Number 4015 (immunoassay of 2,4-0) from U.S. EPA Test Methods for Evaluating 
Solid Waste SW-846. 
E. Note: Existing potable water intakes that are no longer in use, such as those replaced by a connection to a municipal water 
system or a potable water well, are not considered to be functioning potable water intakes. 
F. Drinking water setback distances do not apply to terrestrial applications of 2,4-D adjacent to water bodies with potable water 
intakes. 
STORAGE AND DISPOSAL 
Do not contaminate water, food or feed by storage or disposal. 
PESTICIDE STORAGE: Always store pesticides in a secured warehouse or storage building. Store at temperatures above 32°F. If 
allowed to freeze, rewarm to 40°F, remix thoroughly before using. This does not alter this product. Containers should be opened in 
well-ventilated areas. Keep container tightly sealed when not in use. Do not stack cardboard cases more than two pallets high. Do 
not store near open containers of fertilizer, seed or other pesticides. 
PESTICIDE DISPOSAL: Pesticides wastes are toxic. If container is damaged or if pesticide has leaked, contain all spillage. Absorb 
and clean up all spilled material with granules or sand. Place in a closed, labeled container for proper disposal. Improper disposal 
of excess pesticide, spray mixtures, or rinsate is a violation of Federal law and may contaminate groundwater. If these wastes 
cannot be disposed of by use according to label instructions, contact your State Pesticide or Environmental Control Agency, or the 
Hazardous Waste representative at the nearest EPA Regional Office for guidance. 
CONTAINER DISPOSAL: Nonrefillable container. Do not reuse or refill this container. Triple rinse (or equivalent) promptly after 
emptying. Empty the remaining contents into application equipment or a mix tank and drain for 10 seconds after the flow begins 
to drip. Fill the container 1/4 full with water and recap. Shake for 10 seconds. Pour rinsate into application equipment or a mix tank 
or store rinsate for later use or disposal. Drain for 10 seconds after the flow begins to drip. Repeat this procedure two more times. 
Then offer for recycling or reconditioning, or puncture and dispose of in a sanitary landfill, or by other procedures approved by State 
and local authorities. Plastic containers are also disposable by incineration, or, if allowed by State and local authorities, by burning. 
If burned, stay out of smoke. 
WARRANTY DISCLAIMER 
The directions for use of this product must be followed carefully. TO THE EXTENT CONSISTENT WITH APPLICABLE LAW, (1) 
THE GOODS DELIVERED TO YOU ARE FURNISHED" AS IS" BY MANUFACTURER OR SELLER AND (2) MANUFACTURER AND 
SELLER MAKE NO WARRANTIES, GUARANTEES, OR REPRESENTATIONS OF ANY KIND TO BUYER OR USER, EITHER 
EXPRESS OR IMPLIED, OR BY USAGE OF TRADE, STATUTORY OR OTHERWISE, WITH REGARD TO THE PRODUCT SOLD, 
INCLUDING, BUT NOT LIMITED TO MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, USE, OR ELIGIBILITY OF 
THE PRODUCT FOR ANY PARTICULAR TRADE USAGE. UNINTENDED CONSEQUENCES, INCLUDING BUT NOT LIMITED TO 
INEFFECTIVENESS, MAY RESULT BECAUSE OF SUCH FACTORS AS THE PRESENCE OR ABSENCE OF OTHER MATERIALS 
USED IN COMBINATION WITH THE GOODS, OR THE MANNER OF USE OR APPLICATiON, INCLUDING WEATHER, ALL OF 
WHICH ARE BEYOND THE CONTROL OF MANUFACTURER OR SELLER AND ASSUMED BY BUYER OR USER. THIS WRITING 
CONTAINS ALL OF THE REPRESENTATIONS AND AGREEMENTS BETWEEN BUYER, MANUFACTURER AND SELLER, AND NO 
PERSON OR AGENT OF MANUFACTURER OR SELLER HAS ANY AUTHORITY TO MAKE ANY REPRESENTATION OR 
WARRANTY OR AGREEMENT RELATING IN ANY WAY TO THESE GOODS. 
9

( 
LIMITATION OF LIABILITY 
TO THE EXTENT CONSISTENT WITH APPLICABLE LAW, IN NO EVENT SHALL MANUFACTURER OR SELLER BE LIABLE FOR 
SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, OR FOR DAMAGES IN THEIR NATURE OF PENALTIES RELATING 
TO THE GOODS SOLD, INCLUDING USE, APPLICATION, HANDLING, AND DISPOSAL. TO THE EXTENT CONSISTENT WITH 
APPLICABLE LAW, MANUFACTURER OR SELLER SHALL NOT BE LIABLE TO BUYER OR USER BY WAY OF INDEMNIFICATION 
TO BUYER OR TO CUSTOMERS OF BUYER, IF ANY, OR FOR ANY DAMAGES OR SUMS OF MONEY, CLAIMS OR DEMANDS 
WHATSOEVER, RESULTING FROM OR BY REASON OF, OR RISING OUT OF THE MISUSE, OR FAILURE TO FOLLOW LABEL 
WARNINGS OR INSTRUCTIONS FOR USE, OF THE GOODS SOLD BY MANUFACTURER OR SELLER TO BUYER. ALL SUCH 
RISKS SHALL BE ASSUMED BY THE BUYER, USER, OR ITS CUSTOMERS. TO THE EXTENT CONSISTENT WITH APPLICABLE 
LAW, BUYER'S OR USER'S EXCLUSIVE REMEDY, AND MANUFACTURER'S OR SELLER'S TOTAL LIABILITY SHALL BE FOR 
DAMAGES NOT EXCEEDING THE COST OF THE PRODUCT. 
If you do not agree with or do not accept any of directions for use, the warranty disclaimers, or limitations on liability, do not 
use the product, and return it unopened to the Seller, and the purchase price will be refunded. 
(RV021108R) 
10