crop-chem-docs/corpus/epa_ppls/5905-575.md

# HELENA BW-III

- EPA Reg No: **5905-575**
- Registrant: HELENA AGRI-ENTERPRISES, LLC, D/B/A HELENA CHEMICAL COMP
- Signal word: Danger
- Active ingredients: Dicamba (10.8%); 2,4-D (24.16%)
- Label accepted: 2014-10-24
- Source PDF: https://www3.epa.gov/pesticides/chem_search/ppls/005905-00575-20141024.pdf

---
UNITED STATES ENVIRONMENTAL PROTECTION AGENCY
WASHINGTON, D.C. 20460
OFFICE OF
CHEMICAL SAFETY AND
POLLUTION PREVENTION
Bill Washburn
Helena Chemical Company r,p-y .
255 Schilling Blvd. Suite 300 UU ^ 4 2DH
Collierville, Tennessee 38017
Subject: Label Amendment: Adding Sod Farms, Ornamental and Recreational Turf
Helena BW III
EPA Reg. No.: 5905-575
Decision No.: 491503
Application dated: May 15, 2014
Dear Mr. Washburn:
The labeling referred to above, submitted in connection with registration under the Federal
Insecticide, Fungicide, and Rodenticide Act (FIFRA), as amended, is acceptable.
A stamped copy of your labeling is enclosed for your records. This labeling supersedes all
previously accepted labeling. You must submit one (1) copy of the final printed labeling before
you release the product for shipment with the new labeling. In accordance with 40 CFR 152.130(c),
you may distribute or sell this product under the previously approved labeling for 18 months from
the date of this letter. After 18 months, you may only distribute or sell this product if it bears this
new revised labeling or subsequently approved labeling. "To distribute or sell" is defined under
FIFRA section 2(gg) and its implementing regulation at 40 CFR 152.3.
If you have any questions regarding this letter, please feel free to contact Shanta Adeeb at
(703) 347-0502 or adeeb.shanta@epa.gov.
Sincerely,
Kathryn Montague
Product Manager 23
Herbicide' Branch
Registration Division (7505P)

r
HELENA BW III
For control of a wide-spectrum of annual, biennial, and perennial broadleaf weeds
and brush in Pastures, Rangelands and Grass (Hay, Silage); Conservation
Reserve Program Land; General Farmstead Areas; Post-Harvest, Fallow, Crop
Stubble and Set Aside Acres; Forest Management; Sorghum; Wheat; Roadsides,
Rights-of-way, Industrial Sites and similar Non-crop areas
ACTIVE INGREDIENT(S):
3,6-dichloro-o-methyoxybenzoic acid* 10.80% ^ - __-_. ^
(2,4-dichlorophenoxy) acetic acid* 24.16% A G C K P J
OTHER INGREDIENTS. :.....: 65.04% !
TOTAL 100.00% ;
Equivalent to: 'Dicamba Acid 1.0 Ibs./gal (CAS #1918-00-9) ... - ., ... ,
-2,4-D Acid 2.3 IbsJgal., (CAS #94-75-7) ' '^ ].{£ ^T^SfSt
Isomer specific byAOAC Method 6.D01-5 (12th Ed.) • :.\nvicfeii &>.? tins pessidtis '
KEEP OUT OF REACH OF CHILDREN
DANGER/PELIGRO
Si usted no entiende la etiqueta, busque a alguien para que se la explique a usted en detalle.
(If you do not understand the label, find someone to explain it you in detail.).
FIRST AID
IF IN EYES
IF INHALED
IF SWALLOWED
IF ON SKIN OR
CLOTHING
• Hold eye open and rinse slowly and gently with water for 15-20 minutes.
• Remove contact lenses, if present, after first 5 minutes, then continue rinsinc
eye.
• Call a poison control center or doctor for treatment advice
• Move person to fresh air.
• If person is not breathing, call 911 or an ambulance, then give artificial
respiration preferably mouth-to-mouth if possible.
• Call a poison control center or doctor for further treatment advice.
• Call a poison control center or doctor immediately for treatment advice.
• Have a person sip a glass of water if able to swallow. .
• Do not induce vomiting unless told to do so by a poison control center or
doctor.
• Do not give anything by mouth to an unconscious or convulsing person.
• Take off contaminated clothing.
• Rinse skin immediately with plenty of water for 15-20 minutes.
• Call a poison control center or doctor for further treatment advice.
HOT LINE NUMBER - Have the product container or label with you when calling a poison control center
or doctor or going for treatment. You may also contact 1-800-424-9300 for emergency medical treatmen
information.
NOTE TO PHYSICIAN: Probable mucosal damage may contraindicate the use of gastric lavage.
SEE INSIDE PANEL FOR ADDITIONAL PRECAUTIONS AND DIRECTIONS FOR USE
EPA REG NO. 5905-575 NET CONTENTS:
EPA EST. NO. 42750-MO-001 AD 091610
Manufactured For:
Helena Chemical Company
225 Schilling Blvd., Suite 300
Collierville,TN38017
Filename: HELENA BW-III (5905-575) 082114 CLN.doc

f
PRECAUTIONARY STATEMENTS
HAZARDS TO HUMANS AND DOMESTIC ANIMALS
DANGER. Corrosive. Causes irreversible eye damage. Harmful if inhaled. Harmful if swallowed.
Do not get in eyes or on clothing. Avoid contact with skin. Avoid breathing spray mist.
PERSONAL PROTECTIVE EQUIPMENT (PPE)
Some materials that are chemical-resistant to this product are butyl rubber, natural rubber,
neoprene rubber or nitrite rubber. If you want more options, follow the instructions for Category A
on an EPA chemical-resistance category selection chart.
All mixers, loaders, applicators, flaggers, and other handlers must wear:
Long-sleeved shirt and long pants
Chemical-resistant gloves
Chemical-resistant apron when , mixing or loading, cleaning up spills or equipment, or
otherwise exposed to the concentrate.
Shoes plus socks, and
Protective eyewear (goggles, faceshield, or safety glasses).
See engineering controls for additional requirements.
Follow manufacturer's instructions for cleaning/maintaining PPE. If no such instructions for
washables exist, use detergent and hot water. Keep and wash PPE separately from other
laundry.
If this container contains 5 gallons or more in capacity, do not open pour. A mechanical system
(such as a probe and pump or spigot) must be used for transferring the contents of this container.
If the contents of a non-refillable pesticide container are emptied, the probe must be rinsed before
removal. If the mechanical system is used in a manner that meets the requirements listed in the
Worker Protection Standard (WPS) for agricultural pesticides (40 CFR 170.240 (d) (4)) the
handler PPE requirements may be reduced or modified as specified in the WPS.
ENGINEERING CONTROL STATEMENTS
When handlers use enclosed cabs, or aircraft in a manner that meets the requirements listed in
the Worker Protection Standard (WPS) for agricultural pesticides [40 CFR 170.240 (d)(4-6)], the
handler PPE requirements may be reduced or modified as specified in the WPS.
Pilots must use cockpits in a manner that meets the requirements, listed in the Worker Protection
Standard (WPS) for agricultural pesticides (40 CFR 170.240(d) (4-6).
USER SAFETY RECOMMENDATIONS
Users must:
• Wash hands before eating, drinking, chewing gum, using tobacco or using the toilet.
• Remove clothing/PPE immediately if pesticide gets inside. Then wash thoroughly and
change into clean clothing. If pesticide gets on skin, wash immediately with soap and water.
• Remove PPE immediately after handling this product. Wash the outside of gloves before
removing. As soon as possible, wash thoroughly and change into clean clothing. ,
Filename: HELENA BW-III (5905-575) 082114 CLN.doc

c
ENVIRONMENTAL HAZARDS
This pesticide is toxic to fish and aquatic invertebrates. Do not apply directly to water, to areas
where surface water is present, or to intertidal areas below the mean high watermark. Drift and
runoff may be hazardous to aquatic organisms in water adjacent to treated areas. Do not
contaminate water when disposing of equipment wash water orrinsate.
This chemical has properties and characteristics associated with chemicals detected in
groundwater. The use of this chemical in areas where soils are permeable, particularly where the
water table is shallow, may result in groundwater contamination. Application around a cistern or
well may result in contamination of drinking water or groundwater.
Groundwater Contamination: Most cases of groundwater contamination involving phenoxy
herbicides such as 2,4-D have been associated with mixing/loading and disposal sites. Caution
must be exercised when handling 2,4-D pesticides at such sites to prevent contamination of
groundwater supplies. Use of closed systems for mixing or transferring this pesticide will reduce
the probability of spills. Placement of the mixing/loading equipment on an impervious pad to
contain spills will help prevent groundwater contamination.
Endangered Species.Concerns: The use of any pesticide in.a manner that may kill or otherwise
harm an endangered species or adversely modify their habitat is a violation of federal law.
DIRECTIONS FOR USE
It is a violation of Federal law to use this product in a manner inconsistent with its labeling. Do
not apply this product in a way that will contact workers or other persons, either directly or through
drift. Only protected handlers may be in the area during application. For any requirements
specific to your State or Tribe, consult the agency responsible for pesticide regulation. This
labeling must be in the user's possession during application.
Use of this product in certain portions of California, Oregon and Washington is subject to the
January 22, 2004 Order for injunctive relief in Washington Toxics Coalition, et al. v. EPA, C01-
0132C, (W.D. WA). For further information, please refer to EPA Web Site:
http://www.epa.gov/espp.
AGRICULTURAL USE REQUIREMENTS
Use this product only in accordance with its labeling and with the Worker Protection Standard,
40 CFR part 170. This Standard contains requirements for the protection of agricultural workers
on farms, forests, nurseries, and greenhouses, and handlers of agricultural pesticides. It
contains requirements for training, decontamination, notification, and emergency assistance. It
also contains specific instructions and exceptions pertaining to the statements on this label
about personal protective equipment (PPE), and restricted-entry interval. The requirements in
this box only apply to uses of this product that are covered by the Worker Protection Standard.
Do not enter or allow worker entry into treated areas during the restricted entry interval (REI) of
48 hours.
PPE required for early entry to treated areas that is permitted under the Worker Protection
Standard and that involves contact with anything that has been treated, such as plants, soil, or
water, is:
• Coveralls worn over short-sleeved shirt and short pants. __
Filename: HELENA BW-I/I (5905-575) 082114 CLN.doc

r r 31
Chemical resistant gloves made of any waterproof material
Chemical resistant footwear plus socks
Chemical-resistant headgear for overhead exposure
Protective eyewear
NON-AGRICULTURAL USE REQUIREMENTS
The requirements in this box apply to uses of this product that are NOT within the scope of the
Worker Protection Standard for agricultural pesticides (40 CFR Part 170). The WPS applies
when this product is used to produce agricultural plants on farms, forests, nurseries, or
greenhouses.
Do not enter or allow people (or pets) to enter the treated area until sprays have dried.
USE REQUIREMENTS FOR PASTURES, PERENNIAL GRASSLANDS, RANGELAND,
FALLOW LAND AND NONCROP AREAS: Do not enter treated areas until spray has dried.
For early entry to treated areas, wear eye protection, chemical-resistant gloves, long-sleeved
shirt, long pants, shoes and socks.
TURF USE REQUIREMENTS: Do not allow persons (other than applicator) or pets on treated
area during application. Do not enter treated areas until spray has dried.
NOTE: For application to turf being grown for sale or other commercial use as sod, or for
commercial seed production, or for research purposes, follow AGRICULTURAL USE
REQUIREMENTS on this label.
STORAGE AND DISPOSAL
PROHIBITIONS: Do not contaminate water, food, or feed by storage and disposal.
PESTICIDE STORAGE: Do not store below temperature of 32°F or above 100°F. Store in
original container in a well-ventilated area separately from fertilizer, feed, and foodstuffs. Keep
container tightly closed when not in use. Reduce stacking height where local conditions can
affect package strength. Do not store under conditions that might adversely affect the container
or its ability to function properly.
PESTICIDE DISPOSAL: Pesticide wastes are toxic. Wastes resulting from the use of this
product must be disposed of on site or at an approved waste disposal facility. Improper disposal
of excess pesticide, spray mixture, or rinsate is a violation of Federal law and may contaminate
groundwater. If these wastes cannot be disposed of by use according to label instructions,
contact your State Pesticide or Environmental Control Agency, or the Hazardous Waste
representative at the nearest EPA Regional Office for guidance.
CONTAINER DISPOSAL: Non-refillable containers (non-refillable < 5 gallons): Do not reuse or
refill this container. Offer for recycling, if available. Triple rinse or pressure rinse container (or
equivalent) promptly after emptying.
Filename: HELENA BW-III (5905-575) 082114 CLN.doc

r r
(non-refillable <5 gallons): Triple rinse as follows: Empty the remaining contents into application
equipment or a mix tank and drain for 10 seconds after the flow begins to drip. Fill the container
% full with water and recap. Shake for 10 seconds. Pourrinsate into application equipment or a
mix tank or store rinsate for later use or disposal. Drain for 10 seconds after the flow begins to
drip. Repeat this procedure two more times. Then offer for recycling if available or puncture and
dispose of in a sanitary landfill or by incineration, or, if allowed by state and local authorities, by
burning. If burned, state out of smoke.
(non-refillable >5 gallons): Triple rinse as follows: Empty the remaining contents into application
equipment or a mix tank. Fill the container 1/4 full with water. Replace and tighten closures. Tip
container on its side and roll it back and forth, ensuring at least one complete revolution, for 30
seconds. Stand the container on its end and tip it back and forth several times. Turn the
container over onto its other end and tip it back and forth several times. Empty the rinsate into
application equipment or a mix tank or store rinsate for later use or disposal. Repeat this
procedure two more times. Then offer for recycling if available or puncture and dispose of in a
sanitary landfill or by incineration, or, if allowed by state and local authorities, by burning. If
burned, state out of smoke.
Pressure rinse as follows (all sizes): Empty the remaining contents into application equipment or
a mix tank and continue to drain for 10 seconds after the flow begins to drip. Hold container
upside down over application equipment or mix tank or collect rinsate for later use for disposal.
Insert pressure rinsing nozzle inside of the container, and rinse at about 40 PSI for at least 30
seconds. Drain for 10 seconds after the flow begins to drip.
Refutable container (250 gallon & bulk): Refill this container with pesticide only. Do not reuse
this container for any other purpose. Cleaning the container before final disposal is the
responsibility of the person disposing of the container. Cleaning before refilling is the
responsibility of the refiller.
To clean the container before final disposal, empty the remaining contents from the container
into application equipment or mix tank. Fill the container about 10 percent full with water.
Agitate vigorously or recirculate water with the pump for 2 minutes. Pour or pump rinsate into .
application equipment or rinsate collection system. Repeat this rinsing process two more times.
Then offer for recycling if available or puncture and dispose of in a sanitary landfill or by
incineration, or, if allowed by state and local authorities, by burning. If burned, state out of
smoke.
In Case of Spill: In case of large-scale spillage regarding this product, call ChemTrec 800-424-
9300.
Steps to be taken in case material is released or spilled:
Dike and contain the spill with inert material (sand, earth, etc) and transfer liquid and solid diking
material to separate containers for disposal. Remove contaminated clothing, and wash affected
skin areas with soap and water. Wash clothing before re-use. Keep the spill out of all sewers
and open bodies of water.
31
Filename: HELENA BW-III (5905-575) 082114 CLN.doc

r r
I. PRODUCT INFORMATION
BW III is a postemergence herbicide for controlling a wide spectrum of annual, biennial,
and perennial broadleaf weeds and brush in pastures, range/and, and grass (hay,
silage); sorghum; wheat; conservation reserve program land; postharvest, fallow, crop
stubble, set-aside acres; general farmstead areas; certain noncrop areas, and for forest
management.
Mode of Action
BW III contains two active ingredients uniquely formulated to be used alone or tank
mixed with other listed products as well as liquid fertilizer solutions. BW III is readily
absorbed by plants through shoot and root uptake, translocates throughout the plant's
' system, and accumulates in areas of active growth. BW III interferes with the plant's
growth hormones (auxins) resulting in death of many broadleaf weeds.
For best results, thoroughly clean sprayer equipment (tank, lines, and nozzles)
immediately after use by flushing system with water and heavy duty detergent or other
suitable tank cleaner.
II. APPLICATION INSTRUCTIONS
Apply BW III at the rates and growth stages listed in Tables 1 and 2 as follows unless
instructed differently by section on "Food/Feed Crop Specific Information" or "Non-
Food/Feed Use (Land not Harvested, Grazed or Foraged)-Specific Information." BW III
may be applied using water or sprayable fluid fertilizer as a carrier. Sprayable fluid
fertilizer may be used as the carrier in preplant or pre-emergence use for all crops
listed on this label. Postemergence uses with sprayable fluid fertilizer may be made on
pasture, hayland, or wheat crops only. The most effective application rate and timing
varies based on the target weed species (refer to Table I). In mixed populations of
weeds the correct rate is determined by the weed species requiring the highest rate.
Delaying application permits weeds to exceed the maximum size and will prevent
adequate control. For certain specified applications liquid fertilizer or oil may replace
part or all of the water as diluent. If dry flowable (DF), wettable powder (WP) or flowable
(F) tank mix products are to be used, these should generally be added to the spray tank
first. Follow the mixing directions on the labels of the tank mix products.
Apply product only when active weed growth is evident.
Chemigation Prohibition •
Restrictions:
Do not apply this product through any type of irrigation system.
Do not apply this product in a way that will contact workers or other persons,
either directly or through drift. Only protected handlers may be in the area
during application.
Filename: HELENA BW-III (5905-575) 082114 CLN.doc

c
Spray Coverage
Weeds must be thoroughly covered with spray. Dense leaf canopies shelter smaller
weeds and prevent adequate spray coverage. Do not apply more than 2 applications
per year.
Sensitive Crop Precautions
BW III may cause injury to. desirable trees and plants, particularly beans, cotton, flowers,
fruit trees, grapes, ornamentals, peas, potatoes, soybeans, sunflowers, tobacco,
tomatoes and other broadleaf plants when contacting their roots, stems or foliage. At
high temperatures (about 85 degrees or higher), vapors from this product may cause
injury to the aforementioned susceptible crops. These plants are most sensitive to BW
III during their development or growing stage. Do not treat areas where either possible
downward movement into the soil or surface washing may cause contact of BW III with
the roots of desirable trees and shrubs.
Aerial Application Methods and Equipment
Water Volume: Use 3-10 gallons of water per acre. Use the higher spray volume when
treating dense or tall vegetation.
Application Equipment: Select nozzles designed to produce minimal amounts of fine
spray particles. Make applications at the lowest stage height to reduce the exposure of
spray droplets to evaporation and wind. The applicator must follow the most restrictive
use cautions to avoid drift hazards, including those found in this labeling as well as
applicable state and local regulations and ordinances.
Spray Drift Management
PREVENTING SPRA Y DRIFT A T THE APPLICA TION SITE IS THE RESPONSIBILITY
OF THE APPLICATOR.
Drift Reduction Information
The following information may be helpful in reducing possible spray drift from ground or
aerial applications. Avoid making applications when spray particle may be carried by air
currents to areas where sensitive crops and plants are growing. Do not spray near
sensitive plants if the wind is gusty or in excess of 5 mph and moving in the direction of
nearby sensitive crops or if a temperature inversion exists. Always determine the
direction and distance of possible spray drift prior to application. Leave an adequate
buffer zone between area to be treated and sensitive plants. Coarse sprays are less
likely to drift out of the target area than fine sprays. Properly maintain and calibrate all
spray equipment. The use of agriculturally accepted drift retardants are acceptable and
advised. Avoid applications within the vicinity of susceptible plants when at all possible.
Filename: HELENA BW-III (5905-575) 082114 CLN.doc

f r v^ ( 12,)
A variety of factors including weather conditions (e.g., wind direction, wind speed,
temperature, relative humidity) and method of application (e.g., ground, aerial, airblast)
can influence pesticide drift. The applicator must evaluate all factors and make
appropriate adjustments when applying this product.
Droplet Size
When applying sprays that contain 2,4-D as the sole active ingredient, or when applying
sprays that contain 2,4-D mixed with active ingredients that require a Coarse or coarser
spray, apply only as a Coarse or coarser spray (ASAE standard 572) or a volume mean
diameter of 385 microns or greater for spinning atomizer nozzles.
When applying sprays that contain 2,4-D mixed with other active ingredients that require
a Medium or more fine spray, apply only as a Medium or coarser spray (ASAE standard
572) or a volume mean diameter of 300 microns or greater for spinning atomizer
nozzles.
Wind Speed
Do not apply at wind speeds greater than 15 mph. Only apply this product if the wind
direction favors on-target deposition and there are not sensitive areas (including, but not
limited to, residential areas, bodies of water, known habitat for nontarget species,
nontarget crops) within 250 feet downwind. If applying a Medium spray, leave one
swath unsprayed at the downwind edge of the treated field.
Temperature Inversions
If applying at wind speeds less than 3 mph, the applicator must determine if: a)
conditions of temperature inversion exist, orb)stable atmospheric conditions exist at or
below nozzle height. Do not make applications into areas of temperature inversions or
stable atmospheric conditions.
Susceptible Plants
Do not apply under circumstances where spray drift may occur to food, forage, or other
plantings that might be damaged or crops thereof rendered unfit for sale, use or
consumption. Susceptible crops include, but are not limited to, cotton, okra, flowers,
grapes (in growing stage), fruit trees (foliage), soybeans (vegetable stage),
ornamentals, sunflowers, tomatoes, beans, and other vegetables, or tobacco. Small
amounts of spray drift that might not be visible may injure susceptible broadleaf plants.
Other State and Local Requirements
Applicators must follow all state and local pesticide drift requirements regarding
application of 2,4-D herbicides. Where states have more stringent regulations, they_
must be observed.
Equipment
All aerial and ground application equipment must be properly maintained and calibrated
using appropriate carriers or surrogates.
Filename: HELENA BW-III (5905-575) 082114 CLN.doc

c c '31
The boom length must not exceed 75% of the wingspan or 90% of the rotor blade
diameter.
Release spray at the lowest height consistent with efficacy and flight safety. Do not
release spray at a height greater than 10 feet above the crop canopy unless a greater
height is required for aircraft safety. This requirement does not apply to forestry or
rights-of-way applications.
Do not apply with a nozzle height greater than 4 feet above the crop canopy.
Do not apply during conditions of low humidity and high temperatures.
SENSITIVE AREAS
The pesticide must only be applied when the potential for drift to adjacent sensitive
areas (e.g., residential areas, bodies of water, known habitat for threatened or
endangered species, non-target crops) is minimal (e.g., when wind is blowing away
from the sensitive areas).
Table 1. Application Rate and Timing - Annual Weeds
(For use jn non-food/feed crops only: The addition of liquid fertilizer (28-0-0, 32-0-0) solutions at
Vi the GPA spray solution has shown to give increased efficacy.)
Weeds Controlled
(including ALS -and
triazine-resistant
Beebalm, Spotted
/
Broomweed
Buckwheat, Wild
Buffalobur
Burdock
Buttercup
Chickweed, Common
Cockle, Cow
Cocktebur, Common
Coreopsis, Plains
Croton, Woolly
Dogfennel
Evening Primrose
Flax
Fleabane, Annual
Fixweed
Henbit
Knotweed Spp. .
Kochia
Rate Per Acre (according to weed growth stac
1/3 pints
-
1-3"
'
•' -
-
--
-
-
-
1-4"
-
-
-
-
-
-
-
-
2/3 pints
-
3"
branching
1-6"
-
Pre-flower
Pre-flower
Seedling
<3"
1-6"
1-6"
4-12" .
-
<2"
<2"
1-4"
<3"
-
<3" runners
1-6"
1 pint
- • •
-
-
-
- .
-
1-3"
-
6-12"
-
12-30"
-
-
4-8"
-
Pre-
flower
-
6-10"
1 1/8
pints
Pre-
bloom
Branching
-
1-6"
-
Early
bloom
-
-
12-18"
-
-
10-15"
2-6"
-
8"
-
>3"
runners
10-20"
1 2/3
pints
Post-
bloom-
-
-
-
-
Late
Bloom
-
-
-
' -
-
-
-
-
-
-
Flower
-
• -
e)
2 pints
-
After
branching
-
Flowering
>
-
-
-
-
-
-
-
-
-
-
-
Actively
growing
Actively
growing
Filename: HELENA BW-III (5905-575) 082114 CLN.doc

c r '31
Lambsquarters, Common
Mallow, Common
Morningglory, Ivyleaf
Morningglory, Tall
Mustards, Annual
Mustards, Tansy
Pennycress, Field
Pepperweed, Virginia
Pigweed, Prostrate
Pigweed, Redroot
Pigweed, Smooth
Pigweed, Tumble
Poorjoe
Purslane, Common
Ragweed, Common
Western, Lanceleaf
Sedge1
Shepherdspurse
Smartweed, Pennsylvania
Sneezeweed, Bitter .
Sowthistle
Sunflower
Thistle, Russian
Velvetleaf
-
-
-
-
-
-.
-
--
-
-
-
1-3".
- •
-
-
-
-
-
-
-
1-6"
<3"
Pre-flower
Pre-flower
Rosette
<3"
-
-
<3"
<3"
L_ . <3"
<3"
Prior to
flower
<3"
3-6"
-
Rosette
<4"
1-4"
Rosette
1-3"
-
<6"
6-10"
-
- •
-
-•
1-3"
-
3-10"
-
-
-
3-8"
6-10"
-
-
-
Prior to
flower
-
3-6"
-
6-20"
10-20"
- .
-
Posf-
flower
Early bolt
Rosette .
3-6"
-
-
-
Mature
-
>10"
Actively
growing
• -
-
-
Flower
Bolting
6-24"
Rosette
>20"
-
-
-
-
-
-
-
•After
branching
-
-
-
-
-
-
-
-
-
-
4-72"
-
-
-
-
-
Actively
growing
-
-
-
-
-
-
-
-
-
-
Actively
growing
-
-
-
-
-
-
-
-
-'
'For wse in non-food/feed crop only. Adding crop oil concentrate has shown to improve performance on
actively growing annual sedge.
Table 2. APPLICATION RATE AND TIMING - BIENNIAL AND PERENNIAL WEEDS
(The addition of liquid fertilizer (28-0-0, 32-0-0) at 1A the GPA of the spray solution has proven to
give increase suppression or control on certain species of weeds.)
Weeds Controlled
(including ALS— and
triazine-resistant
Bindweed, Field
Bittercress
Buckeye species
Bullnettle1
Chicory
Clove, Bur
Dandelion, Common
Dewberry, Southern
Rate Per Acre (according to weed growth stage)
1/3
pints
-
-
-
-
-
-
-
-
2/3 pints
-
2-3"
-
-.
-
-
rosette
-
1 pint
-
-
-
-
-
Pre-
flower
-
-
1 1/8 pints
-
-
-
Flower
-
-
bolting
-
1 2/3 pints
-
•
Full leaf
-
Early bolting
-
-
2-31/4 pints
-
-
-
-
-
-
-
Spring fall
Filename: HELENA BW-III (5905-575) 082114 CLN.doc 10

r c '31
Doc/(, Curly
Elderberry1
Goldenrod, Missouri
Groundsel, Texas
Honeysuckle, Hairy
Horsenettle, Carolina
Ivy, Poison'
Knapweed, Black1
Knapweed, Russian1
Knapweed, Spotted
Marshelder
Mesquite^
Milkweed,
Antelopehorn1
Nightshade, Silverleaf
Nightshade, Black
Persimmon, Eastern*
Prickly, Lettuce
Rabbitbrush1
Ragwort, Tansy
Redvine1
Sagebrush, Fringed1
Smartweed
Sorrel, Red
Sowthistle1
Spurge, Leafy1
Tallow Tree, ChineseJ
Thistle, Bull
Thistle, Canada1
Thistle, Musk
Thistle, Plumeless
Vetch, Hairy
Yankeeweed
Yellow Starthistle
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
.-
-
-
-
-
-.
-
-
-
-
-
-
-
-
-
Rosette
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
1-4"
-
-
Prior to
bolting
-
-
Post-
bolting
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
Rosette
-
-
-
Rosette
-
-
Rosette
4-8"
-
-
-
-
3-15"
-
-
-
After bloom
-
-
-
<12"
-
Pre-flower
Full flower
Full flower
-
Rosette
-
Rosette
-
-
-
bolting
-
-
-
bolting
•
Rosette/bolting
bolting
8" full flower
10-18"
-
After bolting
•
Flower
-
Spring or fall
-
-
-
-
-
12"/prebloom
-
-
-
-
-
-
-
-
-
-
-
flower
-
-
-
-
-
-
-
-
-
-
-
Actively
growing
-
-
-
Flower or
berry
-
Actively
growing
Actively
growing
Actively
growing
45-90 days
After
budbreak
Flower
-
Actively
growing
Actively
growing
Actively
growing
-
Actively
growing
Actively
growing
Actively
growing
• '
Actively
growing
Actively
growing
Full leaf
-
Actively
growing
-
-
-
-
Roseffe
-
1 Specified rate will provide top growth suppression only.
2 For improved root kill or woody species such as mesquite and eastern persimmon spray 2 pints of BW III
Filename: HELENA BW-III (5905-575) 082114 CLN.doc II

r r
per acre each year for 3 consecutive years.
3 Under dense populations, a second application may be needed the following growing season. '
For increased control of weeds such as blackberry and dewberry, BW III may be tank mixed with Ally®
herbicide (0.1-0.2 ounces per acre), if labeled for the use site.
Ground Application (Banding)
Do not apply with a nozzle height greater than 4 feet above the crop canopy.
When applying BW III herbicide by banding, determine the amount of herbicide and water volume needed
using the following formula:
Bandwidth in inches x
Row width in inches
Bandwidth in inches x
Row width in inches
Ground Application (Broadcast)
Broadcast rate
per acre
Broadcast rate-
volume per acre
Banding Herbicide
rate per acre
Banding water
volume per acre
Water volume: Use 10-25 gallons of spray solution per broadcast acre for optimal performance. Use the
higher spray volume when treating dense or tall vegetation.
Application Equipment: Select nozzle design to produce minimal amounts of fine spray particles. Spray
nozzles as close to the weeds as is practical for good weed coverage.
Spot or Small Area Application
BW III may be applied to.individual clumps or small areas of undesirable vegetation using handgun or
similar types of application equipment. Apply diluted sprays to allow complete wetting (up to runoff) of
foliage and stems. For knapsack or other small capacity sprayers, prepare a solution ofBW III in water
according to Table 3 (assuming that the spot treatment rate equates to 40 gallons per acre on the
broadcast basis).. Adding a surfactant (0.5% by volume) can help improve control.
Do not make spot treatments in addition to broadcast or band treatments.
Application equipment: Select nozzles designed to produce minimal amounts of fine spray particles.
Spray with nozzles as close to the weeds as is practical for good weed coverage.
Table 3. Knapsack Sprayer Dilution Instructions
Sprayer Capacity (gallons of water)
1 gallon
3 gallons
5 gallons
Amount of BW III to add to the Spray Tank
2/3 fluid ounce *
2 fluid ounces
3 fluid ounces
1 fluid ounce = 2 tablespoons
III. ADDITIVES
To improve burndown of emerged weeds, surfactants and/or low use rates of liquid fertilizers (28-0-0; 32-
0-0), or crop oil concentrate may be used with BW III herbicide orBWIII tank mixes applied after the
weeds have emerged. Crop oil concentrate is for non-food/feed crop uses only. Do not apply tank mixes
that include Ammonium Sulfate or Crop Oil Concentrate to any food/feed crop use listed on this label. For
food/feed crop use, do not use liquid fertilizers that contain Ammonium Sulfate (AMS) as a source of
nitrogen as tolerances in commodities derived from the crop may contain residues that exceed
established tolerances.
Filename: HELENA BW-III (5905-575) 082114 CLN.doc 12

r r
Oil Concentrate
/4 crop oil concentrate must contain either a petroleum or vegetable oil base and must meet all of the
following criteria:
• be non-phytotoxic
• provide good mixing quality in the jar test, and
• be successful in local experience
The exact composition of suitable products will vary; however, vegetable oil and petroleum oil
concentrates should contain emulsifiers to provide good mixing quality. Highly refined vegetable oils have
proven more satisfactory than unrefined vegetable oils. For additional information, see Compatibility Test
for Mix Components.
Adjuvants containing crop oil concentrates may be used forpreplant, pre-emergence and between
cropping applications. Do not use crop oil concentrate for postemergence applications to food/feed crops
(i.e. sorghum, grass (hay or silage), pastures, rangeland, and wheat).
Nitrogen Source
Sprayable Liquid Fertilizers: Use 1A GPA ofsprayable liquid fertilizers (28-0-0; 32-0-0) per acre. Do not
use brass or aluminum nozzles when spraying fertilizers.
Non-Ionic Surfactant
The standard label recommendation is 2-4 pints of an 80% active non-ionic spray surfactant per 100
gallons of water. (Rate will vary with the size and condition of weeds to be controlled. Use lowest rate per
100 gallons when weeds are small and actively growing. As weeds increase in size and or become
hardened off, the rate of non-ionic surfactant will have to be increased to give optimum coverage and
control.)
Table 4. Additive Rate per Acre
Additive1
Non-ionic Surfactant
Sprayable Liquid Fertilizers (28-0-0; 32-0-0)
Crop Oil Concentrate
Rate Additive Per Acre
2-4 pints per 100 gallons2
Vz GPA of spray solution
1 Quart
See manufacturer's label for specific rate recommendations.
2 Use lowest rate per 100 gallons when weeds are small and actively growing. As weeds increase in size
and or become hardened off, the rate of non-ionic surfactant will have to be increased to give optimum.
coverage and control.
IV. TANK MIXING INFORMATION
Tank Mix Partners/Components
The following products may be tank mixed with BW III according to the specific tank mixing instructions in
this label and respective product labels.
• Aim™ (carfentrazone-ethyl)
• Ally® (metsulfuron-methyl)
• Amber® (triasulfuron)
• Asulox® (asulam)
• Atrazine
• Banvel® (dicamba)
Filename: HELENA BW-/II (5905-575) 082114 CLN.doc ' j 3

i
• Basagran® (bentazon)
• Bronate® (bromoxyriil+MCPA)
• Buctril® (bromoxynil)
• Canvas® (thifensulfuron-methyl + tribenuron-methyl + metsulfuron-methyl)
• Clarity® (dicamba)*
• Curtail (clopyralid + 2,4-D)
• Cyclone® (paraquat)
• Dakota® (fenoxaprop-p-ethyl + MCPA)
• Dicamba DMA (dicamba)*
• Distinct® (diflufenzopyr + dicamba) *
• Evik® (ametryn)
• Express® (tribenuron-methyl)
• Fallowmaster® (glyphosate + dicamba)*
• Fallow Star™ (glypohsate + dicamba)* •
• Finesse® (chlorsulfuron + metsulfuron-methyl)
• Glean® (chlorsulfuron)
• Gly Sfar™ Plus (glyphosate)
• Gramoxone® Extra (paraquat)
• Grazon™ P+D (picloram + 2,4-D)*
• Harmony® Extra (thifensulfuron-methyl + tribenuron-methyl)
• Karmex® (diuron)
• Kerb™ (pronamide)
• Laddok® S-12 (bentazon + atrazine)*
• Landmaster® (glyphosate + 2,4-D)*
•• MCPA
• Paramount® (quinclorac)
• Peak® (prosulfuron)
• Permit® (halosulfuron-methyl)
• Rave™ (dicamba + triasulfuron)*
• Roundup® Ultra (glyphosate)
• -Sencor® (metribuzin)
• Sinbar® (terbacil)
• Stinger™ (clopyralid)
• Tiller® (fenoxaprop-p-ethyl) + 2,4-D + MCPA)*
• Tordon™ (picloram)
• Touchdown® (glyphosate)
• 2,4-D*
*When tank mixing with products that contain either 2,4-D or dicamba, do not exceed the annual per acre
application rate for each active ingredient for that crop.
See "VI. Food/Feed Crop Specific Information" section for more information for more details. Read and
follow the applicable Restrictions and Limitations and Directions for Use on all products involved in tank
mixing. Physical incompatibility, reduced weed control, or crop injury may result from mixing BWIII with
other pesticides (fungicides, herbicides, insecticides, or miticides), additives, or fertilizers. Therefore, •
always determine compatibility before tan mixing this product with any other pesticide.
Compatibility Test for Mix Components - Before mixing components, always perform a compatibility jar
test.
For 20 gallons per acre spray volume, use 3.3 cups (800 ml) of water. For other spray volumes adjust
accordingly. Only use water from the intended source at the source temperature.
Filename: HELENA BW-III (5905-575) 082114 CLN.doc j 4

r c
Add components in the sequence indicated in the Mixing Order using 2 teaspoons for each pound or 1
teaspoon for each pint of specified label rate per acre.
Always cap the jar and invert 10 cycles between component additions.
When the components have all been added to the jar, let the solution stand for 15 minutes. Evaluate the
solution for uniformity and stability. The spray solution should not have free oil on the surface, nor fine
particles that precipitate to the bottom, nor thick (clabbered) texture. If the spray solution is not compatible,
repeat the compatibility test with the addition of a suitable compatibility agent. If the solution is still
incompatible, do not mix the ingredients in the same tank.
Mixing Order: If an inductor is used, rinse it thoroughly after each component has been added. Maintain
constant agitation during application.
1. Water- Begin by agitating a thoroughly clean sprayer tank half full of clean water.
2. Agitation - Maintain constant agitation throughout mixing and application.
3. Product in PVA bags. Place any product contained in water-soluble bags into the mixing tank.
Wait until all water-soluble PVA bags have fully dissolved and the product is evenly mixed in the
spray tank before continuing.
4. Water-dispersible products (such as dry flowables, wettable powders, suspension concentrates,
and suspo-emulsions).
5. Water-soluble products (such as BW III).
6. Emulsifiable concentrates (such as oil concentrate when applicable)
7. Water-soluble additives (such as liquid fertilizers (28-0-0; 32-0-0), when applicable)"
8. Remaining quantity of water.
*lf sprayable fluid fertilizer is used as the carrier.
Always perform the Compatibility Test before mixing into the spray tank. Also, when using a
sprayable fluid fertilizer as the carrier, any product contained in PVA bags must first be completely
dissolved in water before the contents can be added to the fertilizer mix.
V. RESTRICTIONS AND LIMITATIONS
• Maximum seasonal use rate: Refer to Table 5:
• Do not make more than two applications per season regardless of individual application rates.
• Preharvest Interval (PHI): Refer to "Food/Feed Crop Specific Information"
• Restricted entry Interval (REI): 48 Hours
• Crop Rotational Restrictions:
The interval between application and planting rotational crop is given below. Always exclude
counting days when the ground is frozen. . Moisture is essential for the degradation of this
herbicide in soil.
Do not apply in greenhouses.
. Planting/replanting restrictions for BW III applications of 3 2/3 pints per acre or less: No rotational
cropping restrictions apply at 120 days or more following application. Additionally, for annual crop
uses in this label including sorghum, follow the preplant use directions under "VI. Food/Feed Crop
Specific Information." For barley, oat, wheat, and other grass seedlings, the interval between
application and planting is 10 days per 2/3 pint per acre.
Planting/replanting restrictions for applications of more than 3 2/3 pints and up to 4 % pints of BW III
per acre: Corn, sorghum, and all other crops grown in areas with 30" or more of annual rain fall may
be planted 120 days or more after application. Barley, oat, wheat, and other grass seedlings may be
planted, if the interval from application to planting is 10 days per 2/3 pint per acre east of the
Mississippi River and 15 days per 2/3 pint per acre west of the Mississippi River. For all other crops in
areas with less than 30" of annual rainfall, the interval between application and planting is 180 days
or more.
Filename: HELENA BW-I/I (5905-575) 082114 CLN. doc

r r
Do nof p/anf cotton for at least 30 days after application and after allowing for a minimum
accumulation of 1" rainfall or overhead irrigation. Do not apply west of the Rockies or to geographic
areas with average annual rainfall less than 25".
• Arid (dry) conditions: It is extremely important that the addition of a suitable Nonionic Surfactant, Oil,
or sprayable fertilizer be used when applying BW III. Higher rates ofBWIII may be needed to control
susceptible weeds in this environment.
• Rainfast Period: Rainfall or irrigation occurring within 4 hours after postemergence applications may
reduce effectiveness ofBWIII.
• Stress: Do not apply to crops under stress such as stress due to lack of moisture, hail damage,
flooding, herbicide injury, mechanical injury, or widely fluctuating temperatures', as unsatisfactory
control may result.
• Do not apply to crops that show injury (leaf phytotoxicity or plant stunting) produced by any other
prior herbicide applications, because this injury may be enhanced or prolonged.
• Do not apply this product through any type of irrigation equipment. Do not contaminate irrigation
ditches or water used for domestic purposes.
• Do not apply more than 8 pints per application and no more than 2 applications per year.
Table 5. Crop Specific Restrictions and Limitations
Crop
Between Crop
Applications
Pasture, Hay,
Silage
Sorghum
Wheat
Maximum Rate
per Acre per
application
3 2/3 pints
2 Yz pints
2/3 pints
2 pints
Maximum Rate
per Acre per
Season
4 % pints
4 % pints
2/3 pints
4 pints
Livestock
Grazing or
Feeding1
Ves
Yes
Ves
Yes
Aircraft
Application
yes
Yes
Yes
Yes
7 Refer to "Food/Feed Crop Specific Information" for grazing and feeding restrictions.
2 Postharvest, Fallow, Crop Stubble, and Set-Aside for broadleaf weed control. Refer to Restrictions &
Limitations in Section V for possible crop rotational restrictions.
VI. FOOD/FEED CROP SPECIFIC INFORMATION
PASTURES, RANGELAND AND GRASS (HAY, SILAGE)
BW III is directed for use on pasture (including pasture grown for hay), range/and, grass grown for hay
or silage, between crop applications/fallow systems. Conservation Reserve Programs, and general
farmstead (non-cropland only).
Refer to Tables 1 and 2 for rate selection based on targeted weed or brush species. Some weed species
will require tank mixes for adequate control.
Pasture & Rangeland Restrictions:
Retreatments may be made as needed; however;
• Do not make more than 2 applications per year.
• Do not exceed a total of2Y2 pints ofBW III per treated acre during a growing season.
• Minimum of 30 days between applications.
• If grass is to be cut for hay, Agricultural Use requirements for the Worker Protection Standard are
applicable.
Filename: HELENA BW-III (5905-575) 082114 CLN.doc 16

0 C
• For program lands, such as Conservation Reserve Program, consult program rules to determine
whether grass or hay may be used. The more restrictive requirements of the program rules or this label
must be followed.
•Do not exceed a combined total of 2.0 pounds a, e. of dicamba per acre per year.
BW III contains 0.125 pounds a.e. of dicamba per pint. When tank mixing with products that contain
dicamba, do not exceed a combined total of 1.0 pound a.e. per acre per application
B W III contain 0.29 pounds a.e. of 2,4-D per pint. When tank mixing with products that contain 2,4-D, do
not exceed a combined total of 4.0 pounds of a.e. per acre per year.
Uses described in this section also pertain to small grains (such as barley, corn, forage, sorghum, oats,
rye, sudangrass, or wheat) grown for pasture, hay and silage only. Newly seeded areas including small
grains grown for pasture or hay, may be injured if rates ofBWIII are greater than 1 % pints per acre are
applied in one application.
In newly established hybrid Bermudagrass, Pangolagrass, and stargrasses (Cynodon spp.) use 1 to 2
pints of BW III per acre to control or suppress weeds after planting vegetative propagules (stolens) of
hybrid bermudagrasses. In addition to the weeds listed in Tables 1 and 2, this rate of BW III will control or
suppress 'annual sedges, broadleaf signalgrass, crabgrass, and goosegrass. Best results will be obtained
if BW III is applied at the germinating stage of weeds. Under favorable conditions, this is usually 7-10
days after planting these grasses. Reduced control can be expected if weeds are allowed to reach 1" in
height before application or if germination of weeds occurs 10 days after application.
Use on bentgrass, susceptible grass pastures (such as carpetgrass, buffalograss, or St. Augustine grass),
lespedeza, wild winter peas, vetch, clover, and alfalfa pastures may result in some degree of plant injury.
When perennial weeds are reaching maturity, mowing and allowing some regrowth will enhance control.
For pasture renovations, wait 3 weeks per 1 Vt pints of BW III used per acre before interseeding or injury
may occur.
If grasses are grown for seed or for seed-down purposes, do not apply aftergrass reaches joint stage.
Grazing and Feeding Non-Lactating Animals: Do not graze non-lactating animals within 7 days of
treatment. Do not permit meat animals being finished for slaughter to graze treated fields within 30 days
of slaughter.
Grazing and Feeding Lactating Animals: Do not graze lactating dairy animals within 7 days of treatment.
Dry hay and Silage : Treated grasses may be harvested for dry hay or silage but do not harvest within 37
days of treatment.
Pasture and Rangeland Tank Mixes
BW III may be applied in tank mixes with one or more of the following herbicides:
Banvel® Dicamba DMA* 2,4-D*
Amber® Clarity® Rave™
"When tank mixing with products that contain either 2,4-D or dicamba, do not exceed the annual per acre
application rate for each active ingredient for that crop.
Filename: HELENA BW-III (5905-575) 082114 CLN.doc j 7

r r 3|
SORGHUM
Rates and Timings
Apply 2/3 pint of BW III per acre to sorghum in the 3-5 leaf stage (4"-8" tall). For best performance apply
when weeds are small (less than 3" tall).
Applications ofBW III to sorghum during periods of rapid growth may result in temporary leaning of plants
or rolling leaves. These effects are usually outgrown within 10-14 days. Sorghum growing under
conditions of stress such as high moisture, low fertility, and abnormal temperature may be more sensitive
to applications ofBWIII. Do not use surfactants or oils with postemergence applications ofBWIII on
sorghum crops. Do not use BW III if the potential for sorghum injury is not acceptable.
If sorghum is grown for pasture, hay or silage, refer to "Pastures, Range/and and Grass (Hay, Silage)"
under "VI. Food/Feed Crop Specific Information" for livestock grazing and feeding restrictions.
Sorghum Tank Mixes
BW III may be applied in tank mixes with one or more of the following herbicides:
Atrazine Laddock®S-12 Peak®
Basagran® Paramount® Permit®
' Buctril®
Sorghum Restrictions:
• Do not graze or feed treated sorghum forage or silage prior to mature grain stage.
• Do not make more than one postemergence application per growing season.
• Do not permit meat or dairy animals to consume treated crop as fodder or forage for 30 days
following application.
• Do not apply B W III to sorghum grown for seed production.
• Pre-Harvest Interval is 30 days.
• Do not exceed a combined total of 2.0 pounds a.e. of dicamba per acre per year.
BW III contains 0.29 pounds a.i. of2,4-D per pint. When tank mixing with products that contain 2,4-D
ester, do not exceed a combined total of 0.5 pounds a. i. per acre per year.
WHEAT
(Fall and Spring Seeded)
If small grains are grown for pasture or hay only, refer to Pastures, Range/and and Grass (Hay, Silage).
Do not graze or harvest for livestock feed prior to crop maturity.
Do not use BW III in wheat underseeded with legumes.
Early Season Application:
Apply up to 2 pints of BW III per acre to wheat unless using one of the wheat specific programs below.
Early season applications to spring-seeded wheat must be made after tillering and before wheat reaches
the 6-leaf stage.
Early season applications to fall-seeded wheat must be made after tillering and prior to the jointing stage.
Care should be taken in staging early developing wheat varieties such as TAM 107, Madison, or
Wakefield to be certain that the application occurs prior to the jointing stage.
Filename: HELENA BW-/II (5905-575) 082114 CLN.doc j g

c
Specific Use Programs for Fall-Seeded Wheat Only:
Up to 3A pints ofBWIII per acre may be applied on fall-seeded wheat after the wheat begins to tiller for
suppression of perennial weeds, such as field bindweed. Applications may be made in the fall following a
frost but before a killing freeze. Periods of extended stress such as cold and wet weather may enhance
the possibility of crop injury. For fall applications only, do not use if the potential for crop injury is not
acceptable.
Preharvest Applications:
BW III can be used to control weeds that may interfere with harvest of wheat. Apply up to 1 % pints of BW
III per acre as a broadcast or spot treatment to annual broadleaf weeds when wheat is in the hard dough
stage and the green color is gone from the nodes (joints) of the stem. Best results will be obtained if
application can be made when weeds are actively growing but before weeds canopy. A waiting interval of
14 days is required before harvest. Do not use preharvest-treated wheat for seed unless a germination
test is performed on the seed with an acceptable result of 95% germination or better. For control of
additional broadleaf weeds or grasses, BW III may be tank mixed with other herbicides such as Ally or Gly
Star™ Plus that are registered for preharvest use in wheat.
Wheat Restrictions.
• Do not exceed a comine total of 2.0 pounds a.e. of dicamba per acre per year.
• Postemergence:
• Do not make more than one application per crop cycle.
• Do not apply more than 2 pints per acre per application.
• Preharvest:
• Do not make more than one application per crop cycle.
• Do nof apply more than 1 % pints per acre per application.
• Pre-Harvest interval is 14 days.
BW III contains 0.125 pounds a.e. of dicamba per pint. When tank mixing with products that contain
dicamba, do not exceed a combined total of 1.0 pound of a.e. per acre per application. Do not exceen a
combined total of 2.0 pounds a.e. of dicamba per acre per year.
BW III contains 0.29 pounds a.i. of2,4-D per pint. When tank mixing with products that contain 2,4-D, :
• Do not exceed a combined total of 1.25 pounds a.e. per acre per crop cycle of 2,4-D for post
emergent use.
• Do not exceed 0.5 pounds of a.e. per acre per crop cycle of 2,4-D for pre-harvest application.
• Do not exceed a total of 1.75 pounds of a.e. per acre per crop cycle for all uses.
Preharvest use of BW III is not registered for use in California.
Table 6 - Wheat Tank Mixes
TANK MIX PARTNER
Aim™
Ally®1
Amber®1
Bronate®
Buctril®
Canvas®1
Curtail
Dakota®*
Express®7
RATE PER ACRE
0.3 ounce
0.05-0.1 ounce
0.14- 0.28 ounce
0.75- 1.5 pints'
1 - 1.5 pints
0.2-0.4 ounce
2-2.67 pints
16 fluid ounces
0.083-0.167 ounce
Filename: HELENA BW-III (5905-575) 082114 CLN.doc 19

r
Finesse®1
Glean®1
Harmony® Extra1
Karmex®J
2,4-D amine
Metribuzin3 (Sencor®)
Peak®1
Stinger™
Tiller®*
0.1 67 -0.33 ounce
0.167 ounce
0.1 67 -0.33 ounce
0.5- 1.5 pounds
4-20 fluid ounces4
0.25 - 0.375 pounds a.i.
0.25 -0.38 ounce
4-5.33 fluid ounces
1-1.7 pints
Do nof use low rates of sulfonylurea herbicide, such as Ally®, Amber®, Canvas®, Express®, Finesse®,
Glean®, Harmony® Extra, and Peak® on more mature weeds or on dense vegetative growth.
2Do not use as a tank mix treatment with Dakota or Tiller on Durum wheat. Do not tank mix with Tiller if
wild oat is the larger weed.
3Tank mixes with Karmex and metribuzin are for use in fall-seeded wheat only.
Between Crop Applications/Fallow Systems, Conservation Reserve Programs, and General
Farmstead
These uses are considered Food/Feed Crops when harvested, grazed, or foraged. Consult section on
"General Tank Mixing Information" for adjuvant restrictions and section on "Additives" for specific use
directions.
'Feeding and Grazing Restrictions for Wheat: Do not graze or feed animals within 7 days of treatment.
VII. NON-FOOD/FEED USE (LAND NOT HARVESTED, GRAZED OR FORAGED) -
SPECIFIC INFORMATION.
BETWEEN CROP APPLICATIONS
Preplant Directions (Postharvest, Fallow, Crop Stubble, Set-Aside) For Broadleaf Weed Control
Restrictions .
• Plant only labeled crops within 29 days following application.
• Limited to 2 applications per year.
• Minimum of 30 days between applications.
• Do not exceed a combined total of 2.0 pounds a.e. ofdicamba per acre per year
BW III contains 0.125 pound a.e. of dicamba per pint. When tank mixing with products that contain
dicamba, do not exceed a combined total of 1.0 pound a.e. per acre per application.
BW III contains 0.29 pounds a.e. of 2,4-D per pint. When tank mixing with products that contain 2,4-D, do
not exceed a combined total of 2,0 pound a. e. per acre per year.
BW III can be applied postharvest in the fall, spring, or summer during the fallow period or to crop
stubble/set-aside acres. Apply to weeds after crop harvest (postharvest) and before a killing frost or in the
fallow cropland or crop stubble the following spring or summer.
See 'V. Restrictions and Limitations" for the specified interval between application and planting to
prevent crop injury.
Filename: HELENA BW-III (5905-575) 082114 CLN.doc 20

c c /3I
Rates and Timings:
Apply 1-3 2/3 pints of BW III per acre. Refer to Table 1 to determine use rates for specific targeted weed
species. Retreatments may be made as needed; however, do not exceed a total of4% pints ofBWIII per
treated acre during a growing season. For best performance, apply BW III when annual weeds are less
than 6" tall, when biennial weeds are in the rosette stage and to perennial weed regrowth in late summer
or fall following a mowing or tillage treatment. The most effective control of upright perennial broadleaf
weeds such as Canada thistle and Jerusalem artichoke occurs if BW III is applied when the majority of
weeds have at least 4-6" of regrowth or for weeds such as field bindweed and hedge bindweed that are in
or beyond the full bloom stage. The addition of liquid fertilizers (28-0-0, 32-0-0) at 1A GPA has shown to
increase efficacy.
Avoid disturbing treated areas following application. Treatments may not kill weeds that develop from
seed or underground plant parts such as rhizomes or bulblets, after the effective period for BW III. For
seedling control, a follow-up program or other cultural practices could be instituted.
Between Crop Tank Mixes:
In tank mixes with one or more of the following herbicides, apply 1.0- 1.25pints of BW III per acre for
control of annual weeds, or 1.25-4.25 pints ofBW III per acre for control of biennial and perennial
weeds.
• Aim™
• Ally®
• Amber®
• Atrazine
• Curtail*
• Cyclone®
• Distinct®"
• Fallowmaster®* •
• Fallow Star™*.
• Finesse®
• glyphosate (Gly Star™ Plus)
• Gramoxone® Extra
• Kerb™
• Landmaster® BW*
• Paramount®
• Sencor®
• Tordon™ 22K
• Touchdown®
• 2,4-D*
*When tank mixing with products that contain 2,4-D or dicamba, do not exceed the annual per acre
application rate for each active ingredient for that crop.
APPLICATIONS TO FALLOW GROUND PRIOR TO PLANTING COTTON
Rates and Timings
Apply BW III as a broadcast or spot treatment to emerged and actively growing weeds at the rate of 1 to 3
2/3 pints per acre. The most effective control of weeds occurs if application is made when weeds are in
the 2-4 leaf stage and rosettes are less than 2" across.
Filename: HELENA BW-III (5905-575) 082114 CLN.doc . 21

Cropping Restrictions
Do not plant cotton for at least 30 days after application and after allowing for a minimum accumulation of
1" rainfall or overhead irrigation. Do not apply west of the Rockies or to geographic areas with average
annual rainfall less than 25".
Tank Mix Treatments
For control of grasses or additional broadleaf weeds, OUTLA W may be tank mixed with CAPROL®,
GRAMOXONE® Extra, and glyphosate herbicides.
FOREST MANAGEMENT
Do not apply under drip line of desirable trees or adjacent to desirable vegetation.
Do not apply more than 1 gallon of product per acre per year.
Maximum: 1 application per year.
Forest Site Preparation
Budbreak Spray: For control of alder, susceptible broadleaf weeds, and susceptible woody plants before
planting forest seedlings, apply up to 2 quarts per acre in a minimum of 10 gallons spray mixture per acre.
Apply as an oil spray (see "Mixing Instructions") after alder buds break, but before foliage is Y« full size. A
water spray including 2 to 4 quarts per acre of diesel oil, fuel oil, stove oil, or crop oil concentrate may
also be used.
Foliage Spray: To control alder and susceptible woody plants before planting forest seedlings, apply up
to 4 pints per acre in a minimum of 10 gallons spray mixture per acre. If desired, apply as a water spray
including up to 1 quart of diesel oil, fuel oil, stove oil, or crop oil concentrate per gallon of water (see
"Mixing Instructions"). For best results, apply after alder foliage has reached full size.
Conifer Release: Some conifers are more susceptible to BWIII than others. To control alder, susceptible
broadleaf weeds, and susceptible woody plants in young conifer stands, apply up to 2 pints per acre in a
minimum of 10 gallons spray mixture per acre. This spring foliage treatment should be applied as a water
spray when 3/> of the brush foliage has full size leaves and before new conifer growth reaches 2 inches in
length. Such stages usually occur between early May and mid-June, but application timing should be
based on growth stages of brush and conifers. Application may cause leader deformation and other
conifer injury, but trees should overcome it during the next growing season.
To control tanoak, madrone, ceanothus, canyon live oak, and -Manzanita, and to release Douglas fir,
hemlock Sitka spruce or grand fir, apply up to 3 pints per acre in'a minimum of 10 gallons spray mixture
per acre. This spring foliage treatment should be applied as a water spray including, if desired, up to 1
quart of diesel oil, fuel oil, stove oil, or crop oil concentrate per gallon of water (see "Mixing Instructions").
Make application before new growth on Douglas fir is 2 inches long. To release ponderosa pine from the
same species, treat before new pine growth begins in the spring. Addition of oil or oil concentrate may
cause unacceptable injury to pines. For dormant applications in late winter or early spring for control of
susceptible woody species, such as alder, willow, poplars, cherry, vine maple, ceanothus, tanoak,
madrone, and Manzanita, apply up to 3 pints per acre in a minimum of 10 gallons spray mixture (with
diesel oil, etc.) per acre. This dormant treatment should be applied in diesel oil, fuel oil, stove oil, or other
suitable diluent such as water plus-crop oil concentrate (see "Mixing Instructions"). Do not use in
plantations where pine and larch are among the desired crop species.
To control hazel dodder (cuscuta coryli) in the Lake states, apply up to 2 pints per acre in a minimum of
10 gallons spray mixture per acre. Apply as a water spray when new shoot growth of hazel is complete
(usually mid-July).
After conifer species such as white pine, ponderosa pine, jack pine, red pine, black spruce, white spruce,
red spruce, and balsam fir crease growth and harden off and brush is still actively growing in late summer,
Filename: HELENA BW-III (5905-575) 082114 CLN.doc 22

c rV v
apply up to 3 pints per acre in a minimum of 10 gallons water spray mixture per acre. Apply as a water
spray to control certain competing hardwoods such as alder, aspen, birch, hazel and willow. However, if
possible injury cannot be tolerated, do not use since this treatment may cause conifer injury.
Forest Roadsides: To control susceptible broadleaf weeds and woody plants on forest roadsides, apply
1 to 3 pints per acre in a minimum of 10 gallons water spray mixture per acre. Apply as a water spray and,
if necessary to ensure penetration of foliage, include up to 3 quarts per acre of diesel oil, fuel oil, stove oil,
or crop oil concentrate (see "Mixing Instructions").
ROADSIDES: MEDIANS; HIGHWAY, RAILROAD, UTILITY AND PIPELINE RIGHTS-OF-WAY;
VACANT LOTS; AROUND UTILITY INSTALLATIONS, TRANSFORMERS, PUMP HOUSES, AND
BUILDINGS; STORAGE AREAS; FENCES; GUARDRAILS; LUMBER YARDS; INDUSTRIAL SITES;
AIRPORTS; TANK FARMS; FARMSTEADS; AND SIMILAR NONCROP AREAS.
Do not apply under drip line of desirable trees or adjacent to desirable vegetation.
For control of many broadleaf weeds and small woody plants, apply 2/3 to 2 pints per acre diluted in 10
gallons of water. Use the high rate for woody plants. Applications may be as broadcast sprays, small area
sprays or spot treatments. For small areas or spot spraying, use 2 fluid ounces per gallon of water and
spray weeds to runoff. Regardless of the method of application, use adequate spray volume for full
coverage of weeds. Preferred application timing is in the early spring when sufficient weeds have
emerged, and when weeds are small and actively growing, but before weeds exceed size limits described
in weed tables. Summer applications to older, drought-stressed weeds are less effective. However,
weeds are more susceptible again in the fall when cooler, wetter conditions support active growth before
a killing frost. For fall treatment of mature weeds or perennial weed regrowth, use up to 1.0 pints per acre
diluted in 10 gallons of water. Several seasons of spring plus fall treatments may be necessary to control
certain perennials. Use of oil sprays or the addition of spray adjuvants improves weed control, but also
increases the risk of damage to desirable ground covers.
Plant Response: Bent grass, other warm season or southern grasses, alfalfa, clover, or other legumes
may be killed or injured. Do not apply when grass is in boot to milk stage, or after heading begins, if grass
production is desired. Do not apply to newly seeded areas until grass is well established. Do not reseed
for at least 30 days following application.
CONSERVATION RESERVE PROGRAMS AND GENERAL FARMSTEAD
BW III is directed for use for Conservation Reserve Programs, general farmstead (non-cropland only),
weed and brush control, or use in State Recognized Noxious Weed areas (non-cropland areas).
Refer to Tables 1 and 2 for rate selection based on targeted weed or brush species. Some weed species
will require tank mixes for adequate control.
Retreatments may be made as needed; however, do not exceed a total of 4 % pints ofBW III per treated -
acre during a growing season.
Restriction : Do not make more than 2 applications per year. Minimum of 30 days between applications.
For control of annual and perennial weeds, do not make more than 2 applications per year with a
minimum of 30 days between applications. For control of woody plants, do not make more than 1
application per year.
Farmstead and Fence-row Treatment Application Instructions
BW III may be applied using water or oil and water emulsions in spot application to control undesirable
vegetation using handgun or similar types of application equipment. In addition to weed species listed in
Tables 1 and 2, these treatments may be used to control or suppress woody plant species listed in Table
7.
Filename: HELENA BW-/II (5905-575) 082114 CLN.doc . 23

c r
To prepare soil and water emulsions, mix in the order and proportions indicated below.
The solution should remain milky colored without an oily layer on top when under agitation. If an oily layer
forms, increase the amount of emulsifier or change to a more effective emulsifier.
Do not exceed 40 gallons of spray solution per treated acre per application. One gallon ofBW III in forty
gallons of spray solution contains 1.0 pounds acid equivalent ofdicamba and 2.3 pounds acid equivalent
of 2,4-D. Spray plants to wet. Do not allow this spray mix to contact desirable vegetation.
To control brush, briars, and weeds along fence-rows surrounding pasture and ranch lands, and fallow
fields, use a tank mix of 1.5% BW III, 88.5% water, 10% diesel oil, and sufficient emulsifier (to mix the
diesel and emulsifier). The diesel oil in this tank mix will damage or kill desirable grasses and should not
be used in pastures or where damage to desirable species cannot be tolerated.
1. Water: Begin by agitating a thoroughly clean sprayer tank with the desired quantity of clean
water. Maintain constant agitation during complete mixing procedure.
2. Emulsifier: Add 0.5% volume to volume of water.
3. BW III: Add 1.5 gallons per 100 gallons of total intended solution.
4. Diesel Oil: Add 10 gallons per 100 gallons of total intended solution.
Maintain constant agitation during application. Under good agitation, the spray solution should be milky
white with no oil layer on top. If oil layer forms, increase the amount of emulsifier or change to a more
effective emulsifier.
For Spraying Foliar Applications
1. Spray when leaves have reached full size but have not hardened due to drought or maturity.
2. Spray individual plants to wet with handgun.
3. For larger stems (up to 3" in diameter) and hard to control species, direct spray stream to base of
stems to wet the stem at soil surface in addition to wetting the foliage.
4. Do not apply under drip line of desirable trees or adjacent to desirable vegetation.
For Dormant Basal Applications
1. Increase diesel oil content to 15% or 15 gallons of diesel oil per 100 gallons of total solution.
2. Spray in late winter and early spring before plants break dormancy.
3. Spray the bottom 24" of the target stem to wet on all sides.
4. For larger stems (up to 3" in diameter) and hard to kill species direct the spray solution to the
base of target stems to wet the soil at the stem/soil junction in addition to wetting the stem.
5. Do not apply under drip line of desirable trees or adjacent to desirable vegetation.
For Cut Surface Treatments
Apply BW III in an undiluted state as a cut surface treatment to control unwanted trees and prevent
sprouts of cut trees.
• Frill or Girdle Treatments: Make a continuous cut or a series of overlapping cuts using an axe to girdle
tree trunk. Spray or paint the cut surface with BW III.
• Stump Treatments: Spray or paint freshly cut surface with BW III. The cambium layer (the area
adjacent to the bark) should be thoroughly wet. Treat stumps within 6 hours after cutting.
• Basal spray, Cut Surface (stumps and frill): Limit of one basal spray or cut surface application per year.
Filename: HELENA BW-III (5905-575) 082114 CLN.doc 24

rV
SOD FARMS
For best results, do not mow turf 1 to 2 days before or after application. Turf watering should be delayed
until the day after application. Do not apply to newly seeded areas until grass is well established and has
been mowed several times. A period of about 30 days after application is usually a sufficient interval
before reseeding. Seeding a small area and observing response is recommended before large scale
seeding.
Cool Season Grasses:
To control many emerged broadleaf weeds in cool season turfgrasses such as tall fescue, • bluegrass, or
perennial ryegrass, apply 1.0 - 4.0 pints per acre. Apply when weeds are small and actively growing
under good moisture conditions. Do not use on centipede, carpetgrass, St. Augustine, bentgrass, or
Dichondra turf, or where desirable clovers are present.
Restrictions:
• Do not use on creeping grasses such as bentgrass except as a spot treatment.
• Do not use on injury-sensitive southern grasses such as St. Augustinegrass.
• Do not use on dichondra or other herbaceous ground covers. Legumes may be damaged or killed.
Precautions:
• Reseeding: Delay reseeding at least 30 days following application. Preferably, with spring application,
reseed in the fall and with fall application, reseed in the spring.
• Use sufficient spray solution for thorough and uniform coverage, and no less than 2 gallons per acre.
Sod Farm Restrictions:
• Do not apply more than 4 pints product (1.2 Ibs ae) per acre per application.
• . Do not make more than 2 applications per year (excluding spot treatments).
• Minimum spray interval between broadcast applications is 21 days.
BW III contains 0.3 pounds a.e. of 2,4-D per pint. When tank mixing with products that contain 2,4-D, do
not exceed a combined total of 4.0 pounds of a.e. per acre per year excluding spot treatments.
ORNAMENTAL AND RECREATIONAL TURFGRASSES.LAWNS,
GOLF COURSES (Fairways, Aprons, Tees, and Roughs), PARKS AND CEMETERIES
Refer to "Turf Use Requirements" in the "Non-Agricultural Use Requirements" section. For best results,
do not mow turf 1 to 2 days before or after application. Turf watering should be delayed for at least 1 hour
after application. Avoid contacting desirable trees, shrubs, flowers or vegetables since plant injury may
result. Do not apply to newly seeded areas until grass is well established and has been mowed several
times. A period of about 30 days after application is usually.a sufficient interval before reseeding grasses
(or other plants). Seeding a small area and observing response is recommended before large scale
seeding.
Cool Season Grasses: To control many emerged broadleaf weeds in cool season turfgrasses such as
tall fescue, bluegrass, or perennial ryegrass, apply 2.0-3.0 pints per acre (0.75 to 1.0 fluid ounces per
1,000 square feet). Preferred application timing for broadcast treatment is in the early spring when small
weeds have emerged and are actively growing under good moisture conditions. For very weedy turf, a
follow-up broadcast or spot application may be needed from 2 to 4 weeks later. Summer applications are
typically spot treatments of individual weeds that have emerged after a spring broadcast treatment. In the
fall when cooler, wetter conditions favor active weed growth, broadcast application may be appropriate for
very weedy turf, such as an area that had no spring broadcast treatment. Do not use on centipede,
carpetgrass, St. Augustine, bentgrass or Dichondra turf, or where desirable clovers are present.
Filename: HELENA BW-III (5905-575) 082114 CLN.doc ' 25

r
Restrictions:
• Do not use on creeping grasses such as bentgrass except as a spot treatment.
• Do not use on injury-sensitive southern grasses such as St. Augustinegrass.
• Do not use on dichondra or other herbaceous ground covers. Legumes may be damaged or killed.
Precautions:
• Reseeding: Delay reseeding at least 30 days following application. Preferably, with spring application,
reseed in the fall and with fall application, reseed in the spring.
Ornamental Turf grass Restrictions:
• Do not apply more than 4 pints product (1.2 Ibs ae) per acre per application.
• Do not make more than 2 applications per year (excluding spot treatments).
• Minimum spray interval between broadcast applications is 30 days.
BW III contains 0.3 pounds a.e. of 2,4-D per pint. When tank mixing with products that contain 2,4-D, do
not exceed a combined total of 3.0 pounds of a.e. per acre per year excluding spot treatments.
Table 7. The following list of trees and vines can be controlled on farmsteads and fencerows as foliar,
basal, or cut surface treatments:
Alder
Ash
Aspen
Basswood
Beech
Blackberry
Blackgum
Cedar
Cherry
Chinquapin
Cottonwood
Creosotebush
Dewberry
Dogwood
Elm
Grape
Greenbriar
Hawthorn (Thornapple)
Hemlock
Hickory
Honeylocust
Hornbeam
Huckleberry
Huisache
Ivy, Poison
Kudzu
Locust, Black
Maple
Mesquite
Oak
Oak, Poison
Olive, Russian
Persimmon, Eastern
Pine
Plum, Sand (Wild Plum)
Poplar
Rabbitbrush
Redcedar, Eastern
Rose, McCartney
Rose, Multiflora
Sagebrush, Fringe
Sassafras
Spruce
Sumac
Sweetgum
Sycamore
Tarbrush
Willow
Witchhazel
Yaupon
Yucca
Filename: HELENA BW-III (5905-575) 082114 CLN.doc 26

c r
Weeds listed in this label:
Annuals
Common Name Scientific Name
Beebalm, Spotted
Bfoomweed, Common
Buckwheat, Wild
Buffalobur
Burdock
Buttercup, Corn
Chickweed, Common
Cockle, Com
Cocklebur, Common
Coreopsis, Plains
Croton, Woolly
Devilsclaw
Dogfennel (Cypressweed)
Evening Primrose, Cutleaf
Flax
Fleabane, Annual
Flixweed
Henbit
Knotweed, Prostrate
Kochia
Lambsquarters, Common
Letttuce, Prickly
Mallow, Common
Morningglory, Ivyleaf
Morningglory, Tall
Mustard, Annual
Mustard, Tansy
Pennycress, Field
Pepperweed, Virginia
Pigweed, Prostrate
Pigweed, Redroot
Pigweed, Smooth
Pigweed, Tumble
Poorjoe
Purslane, Common
Ragweed, Common
Ragweed, Lance-Leaf •
Ragweed, Western
Sedge
Shepherdspurse
Smartweed, Pennsylvania
Sneezeweed, Bitter
Sunflower, Common (wild)
Thistle, Russian '
Monarda punctata
Gutierezia dracunculoides
Polygonum convolvulus
Solanum rostratum
Arctium spp.
Rannculus arvensis
Stellaria media
Agrostemma githago
Xanthium strumarium
Coreopsis tinctoria
Croton capitatus
Proboscidea luisianica
Eupatorium capillifolium
Oenothera facinata
Linum catharticum
Erigeron annuus
Descurainia Sophia
Lamium amplexicaule
Polygonum aviculare
Kochia scoparia
Chenopodium album
Lactuca serriola
Maalva neglecta
Ipomea hederacea
Ipomea purupurea
Brassica spp.
Descurainia pinnata
Thlaspi arvense
Lepidium virginicum
Amaranthus blitoides
Amaranthus retroflexus
Amaranthus hybridus
Amaranthus albus
Dioda feres
Portulaca oleracea
Ambrosia ariemisiifolia
Ambrosia bidentata
Ambrosia psilostachya
Cyperus compressus
Capsella bursa-pastoris
Polygonum pensylvanicum
Helenium amurum
Helianthus annuus
Salsola iberica
Filename: HELENA BW-III (5905-575) 082114 CLN.doc 27

c 31
Biennials and Perennials
Common Name
Bindweed, field
Bittercress
Buckeye
•Bullnettle
Chicory
Clover, Hop
Dandelion
Dock, Curly
Elderberry
Goldenrod, Missouri
Goldenweed, Common
Groundsel
Honeysuckle, Hairy
Horsenettle
Ivy, Poison
Knapweed, Black
Knapweed, Russian
Knapweed, Spotted
Marshelder
Mesquite
Milkweed, Antelopehorn
Nightshade, Silverleaf
Nightshade, Black
Persimmon, Eastern
Rabbitbrush
Ragwort, Tansy
Redvine
Sagebrush, Fringed
Smartweed, Swamp
Sorrel, Red (Sheep Sorrel)
Sowthistle, Perennial
Spurge, Leafy
Starthistle, Yellow
Tallow Tree, Chinese
Thistle, Bull
Thistle, Canada
Thistle, Musk
Thistle, Plumeless
Vetch
Yankeeweed
Scientific Name
Convolvulus arvensis
Cardamine spp.
Aesculus spp.
Cnidosculus stimulosus
Cichorium intybus
Trifoleum aureum
Taraxacum officinale
Rumex crispus
Sambucus Canadensis
Solidago missouriensis
Isocoma coronopifolia
Senecio vulgaris
Lonicera
Solanum caroliniense
Rhus radicans •
Centaurea nigra
Centaurea repens
Centaurea maculosus
Ina annua
Prospois juliflora
Asclepius
Solanum elaegnifolium
Solanum nigrum
Diospyros virginiana
Chrysanthemus pulchellus
Senecio jacobia
Brunnichia ovata
Artemisia frigida
Polygonum coccineum
Rumex acetosella
Sonchus arvensis
Euphorbia esula
Centauria solstitialis
Sapium sebiferum
Cirsium vulgare
Cirsium arvense
Carduus nutans
Carduus acanthoides
Vicia spp.
Eupatorium compositifolium
Food/Feed Crop Uses
This product can be used on the following:
• Conservation Reserve Program Land
• . Fallow Systems (Between Crop Application)
• General Farmstead
• Grain Sorghum
• Grass (Hay or Silage)
• Industrial Sites
Filename: HELENA BW-III (5905-575) 082114 CLN.doc 28

r
• .. Pastures
• Range/and
• Rights-of-Way
• Roadsides
• Non-crop Areas
• Wheat
• Sod Farms
• Ornamentals & Recreational Turf
Look inside for complete Restrictions and Limitations and Application Instructions
These crops are considered Food/Feed crops only when harvested, grazed, or foraged. Otherwise, they
are considered non-Food/Feed uses.
CONDITIONS OF SALE AND WARRANTY
The DIRECTIONS FOR USE of this product reflect the opinion of experts based on field use and tests.
The directions are believed to be reliable and must be followed carefully. Crop injury, ineffectiveness, or
other unintended consequences may result because of such factors as weather conditions or presence of
other materials. All such risks shall be assumed by the Buyer.
HELENA CHEMICAL COMPANY warrants that this product conforms to the chemical description on the
label and is reasonably fit for the purposes referred to in the Directions for Use subject to the inherent
risks referred to above. TO THE EXTENT CONSISTENT WITH APPLICABLE LAW, HELENA CHEMICAL
COMPANY MAKES NO OTHER EXPRESS OR IMPLIED WARRANTY OF FITNESS FOR ANY
PARTICULAR PURPOSE OR OF MERCHANTABILITY OR ANY OTHER EXPRESS OR IMPLIED
WARRANTY. TO THE EXTENT CONSISTENT WITH APPLICABLE LAW, THIS WARRANTY DOES
NOT EXTEND TO, AND THE BUYER SHALL BE SOLELY RESPONSIBLE FOR, ANY AND ALL LOSS
OR DAMAGE WHICH RESULTS FROM THE USE OF THIS PRODUCT IN ANY MANNER WHICH IS '
INCONSISTENT WITH THE LABEL DIRECTIONS.
TO THE EXTENT CONSISTENT WITH APPLICABLE LAW, BUYER'S EXCLUSIVE REMEDY AND
MANUFACTURER'S OR SELLER'S EXCLUSIVE LIABILITY FOR ANY AND ALL CLAIMS, LOSSES,
DAMAGES, OR INJURIES RESULTING FROM THE USE OR HANDLING OF THIS PRODUCT,
WHETHER OR NOT BASED IN. CONTRACT, NEGLIGENCE, STRICK LIABILITY IN TORT OR
OTHERWISE, SHALL BE LIMITED,.AT THE MANUFACTURER'S OPTION, TO REPLACEMENT OF OR
THE REPAYMENT OF THE PURCHASE PRICE FOR THE QUANTITY OF PRODUCT WITH RESPECT
TO WHICH DAMAGES ARE CLAIMED. When Buyer suffers losses or damages resulting from the use or
handling of this product (including claims based on contract, negligence, strict liability, or other legal
theories), Buyer must promptly notify Seller in writing of any claims to be eligible to receive either remedy
stated above. TO THE EXTENT CONSISTENT WITH APPLICABLE LAW, IN NO CASE'SHALL HELENA
CHEMICAL COMPANY OR THE SELLER BE LIABLE FOR CONSEQUENTIAL, SPECIAL OR INDIRECT
DAMAGES RESULTING FROM THE USE OR HANDLING OF THIS PRODUCT. HELENA CHEMICAL
COMPANY and the Seller offer this product, and the Buyer accepts it, subject to the foregoing Conditions
of Sale and Warranty, which may be varied only by agreement in writing signed by a duly authorized
representative of HELEN A CHEMICAL COMPANY. No employee or agent of HELENA CHEMICAL
COMPANY or the Seller is authorized to vary or exceed the terms of this Warranty in any other manner.
Ally®, Canvas®, Express®, Finesse®, Glean®, Harmony®, Karmex®, and Sinbar® are registered
trademarks of E.I. du Pont de Nemours & Company.
Banvel®, Clarity®, Distinct®, Fallowmaster®, and Paramount® are registered trademarks of BASF
Corporation.
Basagran® and Laddok ® S-12 are registered trademarks of BASF AG.
Asulox®, Bronate®, Butril®, Dakota®, Tiller® are registered trademarks of Bayer CropScience.
Filename: HELENA BW-III (5905-575) 082114CLN.doc 29

r r
Amber®, Evik®, Cyclone®, Sencor®, Gramoxone®, Peak®, Rave™, and Touchdown® are trademarks
and/or registered trademarks of Syngenta Crop Protection.
Landmaster®, Permit®, and Roundup® Ultra are registered trademarks of Monsanto Company.
Curtail, Stinger™, Grazon™, Kerb™, and Tordon™ are trademarks of Dow AgroSciences LLC.
Aim™ is a trademark ofFMC Corporation.
Fallow Star™ and Gly Star™ Plus are trademarks ofAlbaugh, Inc.
Filename: HELENA BW-III (5905-575) 082114 CLN.doc 30