crop-chem-docs/corpus/epa_ppls/7969-156.md

# OUTLOOK HERBICIDE

- EPA Reg No: **7969-156**
- Registrant: BASF AGRICULTURAL SOLUTIONS US, LLC
- Signal word: Warning
- Active ingredients: dimethenamid-P (63.9%)
- Label accepted: 2019-11-29
- Source PDF: https://www3.epa.gov/pesticides/chem_search/ppls/007969-00156-20191129.pdf

---
UNITED STATES ENVIRONMENTAL PROTECTION AGENCY 
 WASHINGTON, DC 20460 
 
 
 
PRIA Non-New-Use Label Acceptable v.20150320 
OFFICE OF CHEMICAL SAFETY 
AND POLLUTION PREVENTION 
November 29, 2019 
 
Craig Kleppe 
Agricultural Products Division 
BASF Corporation 
26 Davis Drive 
P.O. Box 13528 
Research Triangle Park, NC 
27709-3528 
 
Subject: PRIA Label Amendment – Amending use pattern to delete the preemergence 
application timing and shift to early postemergence. 
 Product Name: Outlook Herbicide 
 EPA Registration Number: 7969-156 
 Application Date: November 2, 2018 
 Decision Number: 545851 
 
Dear Mr. Kleppe: 
 
The amended label referred to above, submitted in connection with registration under the Federal 
Insecticide, Fungicide and Rodenticide Act, as amended, is acceptable. This approval does not 
affect any conditions that were previously imposed on this registration. You continue to be 
subject to existing conditions on your registration and any deadlines connected with them. 
 
A stamped copy of your labeling is enclosed for your records. This labeling supersedes all 
previously accepted labeling. The next label printing of this product must use this labeling unless 
subsequent changes have been approved. You must submit one copy of the final printed labeling 
before you release the product for shipment with the new labeling. In accordance with 40 CFR 
152.130(c), you may distribute or sell this product under the previously approved labeling for 18 
months from the date of this letter. After 18 months, you may only distribute or sell this product 
if it bears this new revised labeling or subsequently approved labeling. “To distribute or sell” is 
defined under FIFRA section 2(gg) and its implementing regulation at 40 CFR 152.3. 
 
Should you wish to add/retain a reference to the company’s website on your label, then please be 
aware that the website becomes labeling under the Federal Insecticide Fungicide and Rodenticide 
Act and is subject to review by the Agency. If the website is false or misleading, the product 
would be misbranded and unlawful to sell or distribute under FIFRA section 12(a)(1)(E). 40 
CFR 156.10(a)(5) list examples of statements EPA may consider false or misleading. In addition, 
regardless of whether a website is referenced on your product’s label, claims made on the 
website may not substantially differ from those claims approved through the registration process. 
Therefore, should the Agency find or if it is brought to our attention that a website contains false 
or misleading statements or claims substantially differing from the EPA approved registration, 
the website will be referred to the EPA’s Office of Enforcement and Compliance.

Page 2 of 2 
EPA Reg. No. 7969-156 
Decision No. 545851 
 
 
Your release for shipment of the product constitutes acceptance of these conditions. If these 
conditions are not complied with, the registration will be subject to cancellation in accordance 
with FIFRA section 6. If you have any questions, please contact Julia Kerr by phone at 703-347-
0386, or via email at kerr.julia@epa.gov. 
 
Enclosure 
 
 
Sincerely, 
 
Emily Schmid, Product Manager 25 
Herbicide Branch 
Registration Division (7505P) 
Office of Pesticide Pro
grams

A selective residual herbicide for use in certain agricultural crops
Active Ingredient*:
dimethenamid-P: (S)-2-chloro-N-[(1-methyl-2-methoxy)ethyl]-
N-(2,4-dimethyl-thien-3-yl)-acetamide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63.9%
Other Ingredients**: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36.1%
Total: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100.0%
* Contains 6.0 pounds of active ingredient per gallon
** Contains petroleum distillates
EPA Reg. No. 7969-156 EPA Est. No.
KEEP OUT OF REACH OF CHILDREN
WARNING/AVISO
See inside for complete First Aid, Precautionary Statements, Directions For Use,
Conditions of Sale and Warranty, and state-specific crop and/or use site restrictions.
In case of an emergency endangering life or property involving this product,
call day or night 1-800-832-HELP (4357).
Net Contents:
BASF Corporation
26 Davis Drive, Research Triangle Park, NC 27709
Si usted no entiende la etiqueta, busque a alguien para que se la explique a usted en
detalle. (If you do not understand the label, find someone to explain it to you in detail.)
Dimethenamid-P Group 15 Herbicide
11/29/2019
7969-156

2
Precautionary Statements
Hazards to Humans and Domestic Animals
WARNING. 
Causes substantial but temporary eye injury. Harmful if
inhaled, swallowed, or absorbed through the skin.
DO NOT get in eyes or on clothing. Avoid contact with
skin. Avoid breathing spray mist. Prolonged or frequently
repeated skin contact may cause allergic reactions in some
individuals. Wash hands thoroughly with soap and water
after handling and before eating, drinking, chewing gum,
using tobacco, or using the toilet. Remove and wash con-
taminated clothing before reuse.
Personal Protective Equipment (PPE)
Applicators and other handlers must wear:
• Long-sleeved shirt and long pants
• Waterproof gloves
• Shoes plus socks
• Protective eyewear (goggles or a face shield)
User Safety Requirements
Discard clothing and other absorbent materials that have
been drenched or heavily contaminated with this product’s
concentrate. DO NOT reuse them. Follow the manufac -
turer’s instructions for cleaning and maintaining PPE. If no
such instructions for washables exist, use detergent and
hot water. Keep and wash PPE separately from other
 laundry.
Engineering Controls
When handlers use closed systems, enclosed cabs, or air-
craft in a manner that meets the requirements listed in the
Worker Protection Standard (WPS) for agricultural
 pesticides [40 CFR 170.240(d)(4-6)], the handler PPE
 requirements may be reduced or modified as specified in
the WPS.
IMPORTANT:When reduced PPE is worn because a
closed system is being used, handlers must be provided all
PPE specified above for applicators and other handlers
and have such PPE immediately for use in an emergency,
such as a spill or equipment breakdown.
Mixers and loaders for aerial applications must use
a closed system that meets the requirements listed in the
Worker Protection Standard (WPS) for Agricultural
Pesticides [40 CFR 170.240 (d)(4)] for dermal protection,
and must:
• Wear personal protective equipment (PPE) required in the
PPE section of this labeling for applicators and other
 handlers 
• Wear protective eyewear, if the system operates under
pressure
• Either use a closed system that also meets the require-
ments in the WPS for inhalation protection or wear a
NIOSH-approved dust-mist respirator with a TC84
 cartridge
• Be provided and have immediately available for use in an
emergency, such as a spill or equipment breakdown:
coveralls, chemical-resistant footwear, and dust-mist 
respirator, or if using a closed system cab that provides
respiratory protection, a NIOSH-approved dust-mist 
respirator with a TC84 cartridge
FIRST AID
If in eyes
• Hold eyes open and rinse slowly and gently with water for 15 to 20 minutes.
• Remove contact lenses, if present, after the first 5 minutes; then continue rinsing eyes.
• Call a poison control center for treatment advice.
If swallowed
• Call a poison control center or doctor immediately for treatment advice.
• DO NOT induce vomiting unless told to do so by a poison control center or doctor.
• DO NOT give any liquid to the person.
• DO NOT give anything by mouth to an unconscious person.
If on skin or clothing
• Take off contaminated clothing.
• Rinse skin immediately with plenty of water for 15 to 20 minutes.
• Call a poison control center or doctor for treatment advice.
If inhaled
• Move person to fresh air.
• If person is not breathing, call 911 or an ambulance; then give artificial respiration, preferably
by mouth to mouth, if possible.
• Call a poison control center or doctor for further treatment advice.
HOTLINE NUMBER
Have the product container or label with you when calling a poison control center or doctor or going for treatment. 
You may also contact BASF Corporation for emergency medical treatment information: 1-800-832-HELP (4357).
Note to Physician: Contains petroleum distillate. Vomiting may cause aspiration pneumonia.

3
Environmental Hazards
DO NOT apply directly to water, areas where surface water
is present, or intertidal areas below the mean high water
mark. DO NOT contaminate water when disposing of
equipment washwater or rinsate.
Dimethenamid-P has properties that may result in ground-
water contamination. Application in areas where soils are
permeable or coarse and groundwater is near the surface
could result in groundwater contamination.
Dimethenamid-P has properties that may result in surface
water contamination via dissolved runoff and runoff
erosion. Practices should be followed to minimize the
potential for dissolved runoff and/or runoff erosion.
Point-source Contamination. To prevent point-source
contamination, DO NOT mix or load this or any other pes-
ticide product within 50 feet of wells (including abandoned
wells and drainage wells), sinkholes, perennial or intermit-
tent streams and rivers, and natural or impounded lakes
and reservoirs. This setback does not apply to properly
capped or plugged abandoned wells and does not apply to
impervious pad or dike mixing/loading areas as described
below.
Mixing, loading, rinsing, or washing operations performed
within 50 feet of a well are allowed only when conducted
on an impervious pad constructed to withstand the weight
of the heaviest load that may be on or move across the
pad. The pad must be self-contained to prevent surface
water flow over or from the pad. The pad capacity must be
maintained at 110% that of the largest pesticide container
or application equipment used on the pad and have suffi-
cient capacity to contain all product spills, equipment or
container leaks, equipment washwater, and rainwater that
may fall on the pad. The containment capacity does not
apply to vehicles delivering pesticide shipments to the
 mixing/loading site. States may have in effect additional
requirements regarding wellhead setbacks and operational
containment.
Care must be taken when using this product to prevent:
• Back-siphoning into wells
• Spills
• Improper disposal of excess pesticide, spray mixes, or
rinsates
Check valves or anti-siphoning devices must be used on all
mixing equipment.
Movement Dissolved in Runoff or through Soil.
DO NOT apply under conditions which favor runoff.
DO NOT apply to impervious substrates such as paved or
highly compacted surfaces or frozen soils. Groundwater
contamination may occur in areas where soils are perme-
able or coarse and groundwater is near the surface.
To minimize the possibility of groundwater contamination,
carefully follow application rate as affected by soil type in
the Application Instructions section of this label.
DO NOT apply if all three criteria exist: coarse soils classi-
fied as sand (does not include loamy sand or sandy loam),
less than 3% organic matter (as determined by soil tests, if
not known), and where depth to groundwater is 30 feet or
less.
Movement by Water Erosion of Treated Soil.
DO NOT apply or incorporate this product by flood or fur-
row irrigation. Ensure treated areas have received at least
0.5 inch of rainfall before using tailwater for subsequent irri-
gation of other fields.
Endangered Species Protection
This product may have effects on federally listed threatened
or endangered plant species or their critical habitat. When
using this product, you must follow the measures
contained in the Endangered Species Protection Bulletin
for the county or parish in which you are applying the pesti-
cide. To determine if your county or parish has a Bulletin,
and to obtain that Bulletin, consult
http://www.epa.gov/espp/, or call 1-844-447-3813 no
more than 6 months before using this product. Applicators
must use Bulletins that are in effect in the month in which
the pesticide will be applied. New Bulletins will generally be
available from the above sources 6 months before their
effective dates.
To avoid adverse effects on endangered plant species,
applicators must comply with the following mitigation
measures when endangered plant species are known to
occur in proximity of the application site:
• Aerial Application - Leave a 150-foot untreated buffer
between treatment area and endangered plant
 populations.
• Ground Application - Use low-pressure nozzles
according to the manufacturer’s specifications that pro-
duce only medium-to-coarse or very coarse droplets
AND leave a 35-foot untreated buffer between treatment
area and known endangered plant populations.
USER SAFETY RECOMMENDATIONS
Users should:
• Remove clothing/PPE immediately if pesticide gets
inside. Then wash thoroughly and put on clean clothing.
• Remove PPE immediately after handling this product.
Wash the outside of gloves before removing. As soon as
possible, wash thoroughly and change into clean
 clothing.

4
Directions For Use
It is a violation of federal law to use this product in a man-
ner inconsistent with its labeling. DO NOT apply this
 product in a way that will contact workers or other
persons, either directly or through drift. Only protected
 handlers may be in the area during application. For any
requirements specific to your state or tribe, consult the
agency responsible for pesticide regulation.
Unless otherwise directed in supplemental labeling, follow
all applicable directions, restrictions, precautions and
Conditions of Sale and Warranty. This labeling must be
in the user’s possession during application.
(continued)
(continued)
STORAGE AND DISPOSAL
DO NOT contaminate water, food, or feed by storage or
disposal. Open dumping is prohibited.
Pesticide Storage
DO NOT use or store near heat or open flame. Store in
original container in a well-ventilated area separately from
fertilizer, feed, or foodstuffs and away from other
pesticides. Avoid cross-contamination with other
pesticides. Groundwater contamination may be reduced
by diking and flooring of permanent liquid bulk storage
sites with an impermeable material.
STORAGE AND DISPOSAL (continued)
Pesticide Disposal
Wastes resulting from this product must be disposed of
on-site or at a waste disposal facility. Improper disposal of
excess pesticide, spray mix, or rinsate is a violation of fed-
eral law. If these wastes cannot be disposed of according
to label instructions, contact the state agency responsible
for pesticide regulation or the Hazardous Waste represen-
tative at the nearest EPA Regional Office for guidance.
Container Handling
Nonrefillable Container. DO NOT reuse or refill this
container. Triple rinse or pressure rinse container
(or equivalent) promptly after emptying; then offer for
 recycling, if available, or reconditioning, if appropriate, or
puncture and dispose of in a sanitary landfill, or by inciner-
ation, or by other procedures approved by state and local
authorities.
Triple rinse containers small enough to shake
(capacity 
/unif0a35 gallons) as follows: Empty the remaining
contents into application equipment or a mix tank and
drain for 10 seconds after the flow begins to drip. Fill the
container 1/4 full with water and recap. Shake for 10 sec-
onds. Pour rinsate into application equipment or a mix
tank, or store rinsate for later use or disposal. Drain for
10 seconds after the flow begins to drip. Repeat this pro-
cedure two more times.
Triple rinse containers too large to shake
(capacity > 5 gallons) as follows: Empty the remaining
contents into application equipment or a mix tank. Fill the
container 1/4 full with water. Replace and tighten
closures. Tip container on its side and roll it back and
forth, ensuring at least one complete revolution, for
30 seconds. Stand the container on its end and tip it back
and forth several times. Turn the container over onto its
other end and tip it back and forth several times. Empty
the rinsate into application equipment or a mix tank, or
store rinsate for later use or disposal. Repeat this proce-
dure two more times.
Pressure rinse as follows: Empty the remaining
contents into application equipment or mix tank and con-
tinue to drain for 10 seconds after the flow begins to drip.
Hold container upside down over application equipment
or mix tank, or collect rinsate for later use or disposal.
Insert pressure rinsing nozzle in the side of the container
and rinse at about 40 PSI for at least 30 seconds. Drain
for 10 seconds after the flow begins to drip.
Refillable Container. Refill this container with pesticide
only. DO NOT reuse this container for any other purpose.
Triple rinsing the container before final disposal is the
responsibility of the person disposing of the container.
Cleaning before refilling is the responsibility of the refiller.
AGRICULTURAL USE REQUIREMENTS
Use this product only in accordance with its labeling and
with the Worker Protection Standard, 40 CFR Part 170.
This standard contains requirements for the protection of
agricultural workers on farms, forests, nurseries, and
greenhouses, and handlers of agricultural pesticides. It
contains requirements for training, decontamination, notifi-
cation, and emergency assistance. It also contains
specific instructions and exceptions pertaining to the
statements on this label about personal protective equip-
ment (PPE) and restricted-entry interval. The requirements
in this box only apply to uses of this product that are cov-
ered by the Worker Protection Standard.
DO NOT enter or allow worker entry into treated areas
during the restricted-entry interval (REI) of 12 hours.
EXCEPTION: If the product is soil injected or soil incor-
porated, the Worker Protection Standard, under certain
circumstances, allows workers to enter the treated area if
there will be no contact with anything that has been
 treated.
PPE required for early entry to treated areas that is permit-
ted under the Worker Protection Standard and that
involves contact with anything that has been treated, such
as plants, soil, or water, is:
• Coveralls
• Waterproof gloves
• Shoes plus socks
• Protective eyewear (goggles or a face shield)

5
In Case of Emergency
In case of large-scale spill of this product, call:
• CHEMTREC 1-800-424-9300
• BASF Corporation 1-800-832-HELP (4357)
In case of medical emergency regarding this product, call:
• Your local doctor for immediate treatment
• Your local poison control center (hospital)
• BASF Corporation 1-800-832-HELP (4357)
Steps to take if material is released or spilled:
• Dike and contain the spill with inert material (sand, earth,
etc.) and transfer liquid and solid diking material to sepa-
rate containers for disposal.
• Remove contaminated clothing, and wash affected skin
areas with soap and water. 
• Wash clothing before reuse. 
• Keep the spill out of all sewers and open bodies of water.
Product Information
Outlook® herbicide is a selective residual herbicide for
controlling many annual grass weeds, annual broadleaf
weeds, and sedge as they germinate (see Table 1).
Outlook can be used in agricultural field and row crops
including bean (dry), beets [sugar, table (garden)],
corn [field corn (grain, seed, silage), fresh sweet corn, pop-
corn], cotton, fallow, garlic, hops, horseradish, onions (dry
bulb, green), peanut, perennial grasses grown for seed,
potato, pumpkin, radish, rutabaga, shallots (dry bulb),
sorghum (grain), soybean, sweet potato, tuberous and
corm vegetables, turnip, and winter squash.
Table 1. Weeds Controlled
(continued)
Common Name Scientific Name
Annual Grass Weeds
Barnyardgrass Echinochloa crus-galli
Bluegrass, annual Poa annua
Bluegrass, roughstalk Poa trivialis
Brome, California Bromus carinatus
Brome, downy Bromus tectorum
Crabgrass, large Digitaria sanguinalis
Crabgrass, smooth Digitaria ischaemum
Cupgrass, Southwestern Eriochloa gracilis
Cupgrass, woolly1 Eriochloa villosa
Fescue, rattail Vulpia myuros
Foxtail, giant Setaria faberi
Foxtail, green Setaria viridis
Foxtail, yellow Setaria glauca
Goosegrass Eleusine indica
Johnsongrass (seedling)1 Sorghum halepense
Millet, wild proso1 Panicum miliaceum
Panicum, fall Panicum dichotomiflorum
Panicum, Texas1 Panicum texanum
Red rice Oryza sativa
Ryegrass, Italian Lolium multiflorum
Sandbur1 Cenchrus spp.
Shattercane1 Sorghum bicolor
Signalgrass, broadleaf1 Brachiaria platyphylla
Witchgrass Panicum capillare
STORAGE AND DISPOSAL (continued)
Container Handling (continued)
Triple rinse as follows: To clean the container before
final disposal, empty the remaining contents from this
container into application equipment or mix tank. Fill the
container about 10% full with water. Agitate vigorously or
recirculate water with the pump for 2 minutes. Pour or
pump rinsate into application equipment or rinsate collec-
tion system. Repeat this rinsing procedure two more
times.
When this container is empty, replace the cap and seal all
openings that have been opened during use; return the
container to the point of purchase or to a designated lo -
cation. This container must only be refilled with a pesticide
product. Prior to refilling, inspect carefully for damage
such as cracks, punctures, abrasions, worn-out threads
and closure devices. Check for leaks after refilling and
before transport. DO NOT transport if this container is
damaged or leaking. If the container is damaged, or leak-
ing, or obsolete and not returned to the point of purchase
or to a designated location, triple rinse emptied container
and offer for recycling, if available, or dispose of container
in compliance with state and local regulations.

6
Table 1. Weeds Controlled (continued)
Mode of Action
Dimethenamid-P , the active ingredient in Outlook, is a
Group 15 (WSSA) Group K3 (HRAC) herbicide belonging
to the chloroacetamide chemistry class. Outlook is a root-
and-shoot growth inhibitor that controls susceptible
germinating seedlings before or soon after they emerge
from the soil.
Herbicide Resistance Management
Outlook is a Group 15/Group K3 herbicide. Any weed
pop ulation may contain or develop plants naturally resistant
to Outlook and other Group 15 herbicides. Weed species
with resistance to Group 15 may eventually dominate the
weed population if Group 15 herbicides are used repeat-
edly in the same field or in successive years as the primary
meth od of control for targeted species. This may result in
partial or total loss of control of those species by Outlook
or other Group 15 herbicides.
To delay herbicide resistance consider:
• Avoiding the consecutive use of Outlook or other target-
site-of-action Group 15 herbicides that have a similar
target site of action on the same weed species.
• Using tank mixes or premixes with herbicides from differ-
ent target-site-of-action groups as long as the involved
products are all registered for the same use, have differ-
ent sites of action, and are both effective at the tank mix
or prepack rate on the weed(s) of concern.
• Basing herbicide use on a comprehensive IPM
(Integrated Pest Management) program including cultural
and mechanical methods.
• Monitoring treated weed populations for loss of field effi-
cacy, and control of escapes with effective alternative
herbicides or mechanical methods.
• Identify weeds present in the field through scouting and
field history and understand their biology. The weed-
 control program needs to consider all of the weeds
present.
• Scout fields prior to application to identify the weed
species present and their growth stage to determine if
the intended application will be effective.
• Scout fields after application to verify the treatment was
effective.
• Suspected herbicide-resistance weeds may be identified
by these indicators:
1. Failure to control a weed species normally controlled
by the herbicide at the dose applied, especially if con-
trol is achieved on adjacent weeds;
2. A spreading patch of non-controlled plants of a partic-
ular weed species; and
3. Surviving plants mixed with controlled individuals of the
same species.
• If resistance is suspected, treat weed escapes with an
herbicide with a different MOA and/or use non-chemical
methods to remove escapes, as practical, with the goal
of preventing further seed production.
• Report any incidence of non-performance of this product
against a particular weed species to your local BASF
 representative.
• Contacting your local extension specialist, certified crop
advisors, and/or manufacturer for herbicide resistance
management and/or integrated weed management direc-
tions for specific crops and resistant weed biotypes.
Application Instructions
Outlook provides most effective weed control when
applied by ground or aerial equipment and subsequently
incorporated into soil by rainfall, sprinkler irrigation, or
mechanical tillage before weed seedling emergence from
soil. Outlook can also be applied through chemigation. 
Outlook may be applied as a preplant incorporated,
 preplant surface, preemergence, early postemergence, or
Common Name Scientific Name
Annual Broadleaf Weeds
Amaranth, Palmer Amaranthus palmeri
Amaranth, Powell Amaranthus powellii
Beggarweed, Florida1 Desmodium tortuosum
Carpetweed Mollugo verticillata
Chamomile, mayweed Anthemis cotula
Eclipta1 Eclipta alba
Lambsquarters, common1 Chenopodium album
Nightshade, black2 Solanum nigrum
Nightshade, cutleaf2 Solanum triflorum
Nightshade, Eastern black2 Solanum ptycanthum
Nightshade, hairy2 Solanum sarrachoides
Pigweed, prostrate Amaranthus blitoides
Pigweed, redroot Amaranthus retroflexus
Pigweed, smooth Amaranthus hybridus
Pigweed, tumble Amaranthus albus
Purslane, common Portulaca oleracea
Pusley, Florida Richardia scabra
Ragweed, common1 Ambrosia artemisiifolia
Spurge, nodding Chamaesyce nutans
Spurge, spotted Chamaesyce maculata
Waterhemp, common2 Amaranthus rudis
Waterhemp, tall2 Amaranthus tuberculatus
Sedge
Flatsedge, rice Cyperus iria
Nutsedge, yellow2 Cyperus esculentus
1 Partial control or suppression only. To complement control, use
Outlook® herbicide in tank mixes or sequential application with other
herbicides that provide additional control of these weed species.
2 For best control of these species, use the highest rate specified by soil
type. If dry conditions exist near application or excessive rainfall occurs
early in season, a post emergence herbicide or cultivation may be
required to help control these weeds.

7
layby (corn) treatment. Outlook® herbicide may be
applied using water or sprayable fluid fertilizer as the spray
carrier. Additionally, Outlook may be impregnated on and
applied with dry bulk fertilizer. Sprayable fluid fertilizer as a
carrier is not advised for use after crop emergence. Refer
to Additives for more information.
Application Rate
Application rates for Outlook when applied alone, in tank
mix, or in sequential applications are given in Table 2, and
vary by soil texture and organic matter content. Refer to
Crop-specific Information for additional rate information.
Table 2. Outlook Application Rate/Acre
1,2,3
Soil texture groups used in this label are coarse (sand,
loamy sand, sandy loam), medium (silt, silt loam, loam,
sandy clay loam), and fine (sandy clay, silty clay, silty clay
loam, clay loam, and clay).
DO NOT apply on coarse soils classified as sand (does not
include loamy sand or sandy loam) with less than
3% organic matter (as determined by soil tests, if not
known), and where depth to groundwater is 30 feet or less.
When use rates are expressed in ranges, use the lower
rate for more coarsely textured soils lower in organic mat-
ter; use the higher rate for more finely textured soils high in
organic matter.
Preplant Incorporated Application
Apply Outlook and incorporate into the upper (1 to 2 inch-
es) soil surface up to 2 weeks before planting. Use a
 harrow, rolling cultivator, finishing disk, or other implement
capable of giving uniform shallow incorporation. Avoid
deeper incorporation or reduced weed control or crop
injury may result.
Preplant Surface Application
For use in minimum tillage or no-till production systems,
apply Outlook alone or in tank mixes up to 45 days before
planting. When making early preplant application (15 to
45 days before planting), use the highest rate specified for
the specific soil type. Early preplant applications are not for
use on coarse-texture soils or in areas where average
annual rainfall (or rainfall plus irrigation) typically exceeds
40 inches. Early preplant applications may be applied as
part of a split application program where the second appli-
cation is made after planting (use 2/3 of Outlook rate early
followed by 1/3 of rate after planting). A split application is
advised when the initial application is made more than
30 days before planting. Tank mixes with postemergence
herbicides registered for use on the specific crop such as
glyphosate, Touchdown
® herbicide (glyphosate), or
Gramoxone Inteon® herbicide (paraquat) must be used
when weeds are present at the time of application.
Preemergence Surface Application
Broadcast treatment uniformly to the soil surface after
planting and before crop emergence. Rainfall, sprinkler 
irrigation, or shallow mechanical incorporation after appli-
cation is required to move this product into the upper soil
surface where weed seeds germinate. If adequate rainfall
or irrigation does not occur and weed seedling emergence
begins, a shallow cultivation or rotary hoeing will improve
performance.
Early Postemergence Application
Outlook must be applied before weed seedling
emergence or in a tank mix with products registered for
use on the specific crop on this label that control the
emerged weeds. Refer to Crop-specific Information for
specific postemergence applications by crop.
Layby Application
Use Outlook in field corn, seed corn, and popcorn. See
Crop-specific Information - Corn for more details on
layby application.
Split Application
Outlook may be used in split application programs where
applications are made as part of the methods described
above. If applications are less than 2 weeks apart, the total
Outlook rate used must not exceed the maximum rate
given for each specific soil type. If applications are 2 weeks
or more apart, a total Outlook application rate of up to
21 fl ozs/A per year may be used on any soil type in all
labeled crops except corn, cotton, sugar beet, and
soybean. See Crop-specific Information section for
maximum seasonal application rate in corn, cotton, sugar
beet, and soybean.
Fall Application
For use only in the following states: 
Iowa, Minnesota, North Dakota, South Dakota,
Wisconsin, north of Highway 136 in Illinois, and
north of Highway 91 in Nebraska.
Outlook may be used in fall applications to control weeds
in minimum tillage or no-till corn or soybean production
systems planted the following spring. Apply up to
21 fl ozs/A of Outlook to medium-texture and fine-texture
soils with greater than 2.5% organic matter. 
Soil Texture
Organic Matter Content
Less than 3%
(fl ozs)
3% or more 
(fl ozs)
Coarse 12 to 14 14 to 18
Medium
14 to 18 18 to 21
Fine
See tank mix descriptions for the specified application rate ranges of
other herbicides tank mixed with Outlook.
1 The application rates listed are intended for full-season control of
 targeted weeds. Reduced application rates (8 to 16 fl ozs/A of
Outlook) may be used where partial control or reduced length of soil
residual control is required, such as postemergence application, or
 preemergence application where cultivation or sequentially applied
 herbicides will be used for added control of the same targeted weed
species.
Use 8 to 12 fl ozs/A of Outlook on coarse-texture soils. 
Use 12 to 16 fl ozs/A of Outlook on medium-texture and fine-texture
soils.
2 For all early preplant applications, use 21 fl ozs/A of Outlook.
3 On muck soils and high organic matter soils, apply Outlook at
21 fl ozs/A.

8
Fall applications must be made after October 1. Apply
Outlook® herbicide in the fall after crop harvest when soil
temperature at the 4-inch depth is sustained at less than
55º F and before the ground freezes.
Tillage operations may be conducted before or after apply-
ing Outlook. If following an application, tillage should be
no more than 2 to 3 inches deep to uniformly incorporate
the herbicide into the upper soil surface. If a sequential
application program (fall application followed by spring
application of Outlook) is used, the maximum combined
rate of Outlook that may be applied is 21 fl ozs/A per crop
season.
Spray Drift Management
Avoiding spray drift at the application site is the
 responsibility of the applicator. The interaction of many
equipment-related and weather-related factors determines
the potential for spray drift. The applicator and the grower
are responsible for considering all these factors when
 making decisions. Where states have more stringent regu-
lations, they must be observed. The applicator should be
familiar with and take into account the following drift reduc-
tion advisory information.
Controlling Droplet Size
The most effective way to reduce drift potential is to apply
large droplets that provide sufficient coverage and control.
Applying larger droplets reduces drift potential but will not
prevent drift if applications are made improperly or under
unfavorable environmental conditions (see Wind;
Temperature and Humidity; and Temperature
Inversion).
• Volume - Use high flow rate nozzles to apply the highest
practical spray volume. Nozzles with higher rated flows
produce larger droplets.
• Pressure - DO NOT exceed the nozzle manufacturer’s
specified pressures. For many nozzle types, lower pres-
sure produces larger droplets. When higher flow rates are
needed, use higher flow rate nozzles instead of increas-
ing pressure.
• Number of Nozzles - Use the minimum number of noz-
zles that provide uniform coverage.
• Nozzle Orientation - Orienting nozzles so spray is
released parallel to the airstream produces larger droplets
than other orientations and is preferred practice.
Significant deflection from the horizontal will reduce
droplet size and increase drift potential.
• Nozzle Type - Use a nozzle type designed for the
intended application. With most nozzle types, narrower
spray angles produce larger droplets. Consider using
low-drift nozzles. Solid-stream nozzles oriented straight
back produce the largest droplets and the lowest drift.
DO NOT use nozzles producing a mist droplet spray.
Boom Length
For some use patterns, reducing the effective boom length
to less than 3/4 of the wingspan or rotor length may further
reduce drift without reducing swath width.
Application Height
Making applications at the lowest possible height (aircraft,
ground-driven spray boom) that is safe and practical
reduces exposure of droplets to evaporation and wind.
Applications should not be made at a height greater than
10 feet above the top of the largest plants unless a greater
height is required for aircraft safety.
Swath Adjustment
When applications are made with a crosswind, the swath
will be displaced downwind. Therefore, on the upwind and
downwind edges of the field, the applicator must
 compensate for this displacement by adjusting the path of
the application equipment (e.g. aircraft, ground) upwind.
Swath adjustment distance should increase with increasing
drift potential (higher wind, smaller droplets, etc.).
Wind
Drift potential is lowest between wind speeds of 3 to
10 mph. However, many factors, including droplet size and
equipment type, determine drift potential at any given
speed. Avoid application below 3 mph because of variable
wind direction and high inversion potential. 
NOTE: Local terrain can influence wind patterns. Every
applicator should be familiar with local wind patterns and
how they affect spray drift.
Temperature and Humidity
When making applications in low relative humidity, set up
equipment to produce larger droplets to compensate for
evaporation. Droplet evaporation is most severe when con-
ditions are both hot and dry.
Temperature Inversion
Applications should not occur during temperature inversion
because drift potential is high. Temperature inversions
restrict vertical air mixing, which causes small suspended
droplets to remain in a concentrated cloud that can move
in unpredictable directions because of the light, variable
winds common during inversions. Temperature inversions
are characterized by increasing temperatures with altitude
and are common on nights with limited cloud cover and
light-to-no wind. They begin to form as the sun sets and
often continue into the morning. Their presence can be
indicated by ground fog; however, if fog is not present,
inversions can also be identified by the movement of
smoke from a ground source or an aircraft smoke genera-
tor. Smoke that layers and moves laterally in a
concentrated cloud (under low wind conditions) indicates
an inversion, while smoke that moves upward and rapidly
dissipates indicates good vertical air mixing.
Sensitive Areas
Spray drift from applying this product may result in damage
to sensitive plants adjacent to the treatment area. Only
apply this product when the potential for drift to these and
other adjacent sensitive areas (e.g. residential areas,
 bodies of water, known habitat for threatened or
endangered species, or nontarget crops or plants) is mini-
mal. DO NOT apply when the following conditions exist
that increase the likelihood of spray drift from intended

9
 targets: high or gusty winds, high temperatures, low
humidity, temperature inversions.
Wind Erosion
Avoid treating powdery, dry, or light sandy soils when
 conditions are favorable for wind erosion. Under these
 conditions, the soil surface should first be settled by rainfall
or irrigation.
Aerial Application Method and Equipment
Water Volume. Use 2 or more gallons of water per acre.
The actual minimum spray volume per acre is determined
by the spray equipment used. Use adequate spray volume
to provide accurate and uniform distribution of spray parti-
cles over the treated area and to avoid spray drift.
Managing Spray Drift from Aerial
Application
Applicators must follow these requirements to avoid off-
target drift movement:
• Boom Length - The distance of the outermost nozzles
on the boom must not exceed 3/4 the length of the
wingspan or rotor.
• Nozzle Orientation - Nozzles must always point back-
ward parallel with the airstream and never be pointed
downward more than 45 degrees.
• Application Height - Without compromising aircraft
safety, application should be made at a height of 10 feet
or less above the crop canopy or tallest plants.
Applicators must follow the most restrictive use cautions to
avoid drift hazards, including those found in this labeling as
well as applicable state and local regulations and
 ordinances.
Ground Application (Banding)
When applying Outlook® herbicide by banding, calculate
the amount of herbicide and water volume per acre needed
using the following formula:
Ground Application (Broadcast)
Water Volume. Use 5 or more gallons of water per acre.
The actual minimum spray volume per acre is determined
by the spray equipment used. Use adequate spray volume
for accurate and uniform distribution of spray particles over
the treated area and to avoid spray drift.
Cleaning Spray Equipment
Clean application equipment thoroughly by using a strong
detergent or commercial sprayer cleaner according to the
manufacturer’s directions and then triple rinsing the equip-
ment before and after applying this product.
Ground Application (Dry Bulk Fertilizer)
Outlook may be impregnated or coated onto dry bulk
granular fertilizer carriers for preplant surface, preplant
incorporated, or preemergence application. Impregnation
or coating may be conducted by the in-plant bulk system
or the on-board system. When impregnated onto some dry
fertilizer blends, Outlook may exhibit a strong odor.
Perform the mixing operation in a well- ventilated area.
Outlook may also be applied in herbicide tank mixes
where the tank mix companion product is also registered
for these application systems. Individuals or agents selling
Outlook in these application systems are responsible for
following all state and local regulations regarding fertilizer
and herbicide blending.
Addition of a drying agent may be necessary if the fertilizer
and herbicide blend is too wet for uniform application
because of high humidity, high urea concentration, or low
fertilizer use rate. Slowly add the drying agent to the blend
until a flowable mixture is obtained. Drying agents are not
advised for use with on-board impregnation systems.
Under some conditions, fertilizer impregnated with
Outlook may clog air tubes or deflector plates on pneu-
matic application systems. Mineral oil may be added to
Outlook before blending with fertilizer to reduce plugging.
DO NOT use drying agents when mineral oil is used. To
avoid separation of Outlook and mineral oil mixes in cold
temperatures, either keep mixture heated or agitated
before blending with fertilizer. Mineral oil may be used at 
in-plant blending stations or on-board injection systems.
Apply 200 to 750 pounds of the fertilizer and herbicide
blend per acre. Application must be made uniformly to the
soil to prevent possible crop injury and for satisfactory
weed control. Impregnated fertilizer spread at 1/2 rate and
overlapped to obtain a full rate will offer a more uniform dis-
tribution. For granular fertilizer application to protect small
birds and mammals, soil incorporation of the granules is
required. A shallow (1 to 2 inches) incorporation is desir-
able for improved weed control. Deeper incorporation may
result in unsatisfactory weed control.
Use the following formula to calculate the herbicide rate
when using dry bulk fertilizer applications:
Incompatible Mixtures
DO NOT impregnate Outlook or Outlook mixes on
ammonium nitrate, potassium nitrate, or sodium nitrate fer-
tilizers or fertilizer blends. Single superphosphate (0-20-0)
and triple superphosphate (0-46-0) may be impregnated
only with Outlook alone.
bandwidth in inches x
broadcast
rate
per acre
=
banding
herbicide rate
per acrerow width in inches
bandwidth in inches x
broadcast
volume
per acre
=
banding water
volume
per acrerow width in inches
fl ozs/A x 2,000 = fluid ounces
per ton of fertilizerfertilizer (lbs/A)

10
Chemigation Application via Sprinkler and
Drip Irrigation Systems
Outlook® herbicide may be applied as a chemigation
treatment through sprinkler irrigation systems. Apply this
product ONLY through a sprinkler irrigation system of the
following type: center pivot, end tow, hand move, lateral
move, side (wheel) roll, or solid set. DO NOT apply this
product through any other type of sprinkler irrigation
system.
Outlook may also be applied as a chemigation treatment
through drip irrigation systems. All chemigation precautions
mentioned in this label for sprinkler irrigation systems also
apply for drip irrigation systems.
Application may be made alone or in tank mixtures with
other herbicides on this label registered for use in specified
sprinkler or drip irrigation systems. Application must be
made within specific crop stage timings and product use
rates given in the container label Directions For Use.
Uniform distribution of Outlook-treated irrigation water is
the sole responsibility of the applicator and is required to
avoid crop injury, lack of herbicide effective ness, or illegal
pesticide residue in the crop. If you have questions about
calibration, contact State Extension Service specialists,
equipment manufacturers, or other experts.
Proper calibration is the responsibility of the applicator. The
system must be properly calibrated (with water only) to
ensure the amount of Outlook applied corresponds to the
specified rate. Apply Outlook in volume minimums of
0.33 to 0.67 inch of water using the lower volume for
coarse-texture soils and the higher volume for fine- texture
soils. Application made in high volumes of water (more
than 1 inch) may result in reduced weed control.
Meter herbicide dilution into irrigation water through the
entire time of water application for center pivot and lateral
move sprinkler systems. For solid-set and hand-move
sprinkler irrigation systems and drip irrigation systems,
apply Outlook through the system at the beginning of the
set; then follow with additional water to reach volume mini-
mums as listed by soil type. To increase calibration
accuracy of injection metering equipment, dilute Outlook
in a minimum of 3 parts water to 1 part Outlook. Maintain
agitation in injection nurse tanks to keep a uniform herbi-
cide suspension during application.
Special instructions for chemigation:
1. DO NOT apply when wind speed favors drift beyond the
area intended for treatment.
2. DO NOT connect an irrigation system used for pesticide
application to a public water system unless the pesticide
label-prescribed safety devices for public water systems
are in place.
3. A person knowledgeable of the chemigation system and
responsible for its operation, or under the supervision of
the responsible person, shall shut the system down and
make necessary adjustments should the need arise.
4. Recirculate and/or contain tail water (runoff water) from
chemigation that contains Outlook in the field in a
 cistern or holding reservoir from the initial application
and/or used only on adjacent, approved crops for which
Outlook is registered for this type of application.
5. The pesticide injection pipeline must contain a functional,
automatic, quick-closing check valve to prevent the flow
of fluid back toward the injection pump. It must also con-
tain a functional, normally closed, solenoid-operated
valve located on the intake side of the injection pump and
connected to the system interlock to prevent fluid from
being withdrawn from the supply tank when the irrigation
system is either automatically or manually shut down.
6. The sprinkler chemigation system must contain a func-
tional check valve, vacuum-relief valve, and low-pressure
drain appropriately located on the irrigation pipeline to
prevent water-source contamination from backflow. In
addition, systems must use a metering pump, such as a
positive displacement injection pump (e.g. diaphragm
pump) effectively designed and constructed of materials
that are compatible with pesticides and capable of being
fitted with a system interlock.
7. The sprinkler chemigation system must contain function-
al interlocking controls to automatically shut off the
pesticide injection pump when the water pump motor
stops, or in cases where there is no water pump, when
the water pressure decreases to the point where pesti-
cide distribution is adversely affected.
8. The irrigation line or water pump must include a
functional pressure switch that will stop the water pump
motor when the water pressure decreases to the point
where pesticide distribution is adversely affected.
Chemigation systems connected to public water
 systems:
1. Public water system means a system for the provision to
the public of piped water for human consumption if such
system has at least 15 service connections or regularly
serves an average of at least 25 individuals daily at least
60 days out of the year.
2. Chemigation systems connected to public water
systems must contain a functional, reduced-pressure
zone backflow preventer (RPZ) or the functional equiva-
lent in the water supply line upstream from the point of
pesticide introduction. As an option to the RPZ,
discharge the water from the public water system into a
reservoir tank prior to pesticide introduction. There shall
be a complete physical break (air gap) between the out-
let end of the fill pipe and the top or overflow rim of the
reservoir tank of at least twice the inside diameter of the
fill pipe.
3. All chemigation systems connected to public water sys-
tems must also follow restrictions listed in the preceding
section.
Additives
Spray adjuvants have little or no influence on Outlook per-
formance when application is made before weed
emergence. However, several tank mixes with Outlook
require adjuvants to improve burndown of emerged weeds.
Therefore, surfactants and/or low rate fertilizer [28%, 30%,

11
or 32% urea ammonium nitrate (UAN) or ammonium sulfate
(AMS)], or crop oil concentrate (COC) may be used with
Outlook
® herbicide tank mixes applied preplant, preemer-
gence, or early postemergence to the crop.
Follow the adjuvant directions on the tank mix partner’s
label.
When an adjuvant (or a specific adjuvant product, such as
a drift control agent) is to be used with this product, BASF
recommends the use of a Chemical Producers and
Distributors Association (CPDA) certified adjuvant for use
on food crops.
Oil Concentrate
A crop oil concentrate must contain either a petroleum-oil
or vegetable-oil base and must meet all of the following
 criteria:
• Nonphytotoxic
• Contain only EPA-exempt ingredients
• Provide good mixing quality in the jar test
• Successful in local experience
The exact composition of suitable products will vary; how-
ever, vegetable-oil and petroleum-oil concentrates should
 contain emulsifiers to provide good mixing quality.
Highly refined vegetable oils have proven more satisfactory
than unrefined vegetable oils. For additional information,
see Compatibility Test for Mix Components.
The use of adjuvants containing penetrants, such as
 petroleum-based oils, after corn emergence may cause
crop injury.
Nitrogen Source
Urea Ammonium Nitrate (UAN). Use 1 to 2 gallons of
UAN (28%, 30%, or 32% nitrogen solution) per acre.
DO NOT use brass or aluminum nozzles when spraying
UAN.
Ammonium Sulfate (AMS). AMS at 8 to 17 pounds per
100 gallons of spray solution may be substituted for UAN.
Use high-quality AMS (spray grade) to avoid nozzle plug-
ging. Other sources of nitrogen are not as effective as
those mentioned. BASF does not recommend applying
AMS if applied in less than 10 gallons per acre because of
potential problems with precipitation in reduced volumes.
Use AMS only if it has been demonstrated to be successful
in local experience.
Nonionic Surfactant (NIS)
The standard label recommendation is 1 to 2 quarts of an
80% active (NIS) per 100 gallons of water. For certain
weeds, a higher spray surfactant rate is advised.
Tank Mixing Information
It is the pesticide user’s responsibility to ensure that all
products in the mixtures are registered for the intended
use. Read and follow the applicable restrictions and limita-
tions and directions for use on all product labels involved in
tank mixing. Users must follow the most restrictive
 directions for use and precautionary statements of each
product in the tank mixture.
Outlook may be tank mixed or applied sequentially with
other herbicide products registered for use in any labeled
crop found in this label for a broader spectrum of residual
weed control and/or control of emerged weeds. Refer to
the tank mix product labels to confirm that the respective
tank mix products are registered for use on the labeled
crop. Read and follow tank mix product labels for applica-
tion instructions, use restrictions and precautions, and
rotational cropping guidance. Physical incompatibility,
reduced weed control, or crop injury may result from mix-
ing Outlook with other pesticides (fungicides, herbicides,
insecticides, or miticides), additives, or fertilizers. Local
agricultural authorities may be a source of information
when using other than BASF-advised tank mixes.
Compatibility Test for Mix Components
Before mixing components, always perform a compatibility
jar test.
For 20 gallons/A spray volume, use 3.3 cups (800 mL) of
water. For other spray volumes, adjust rates accordingly.
Only use water from the intended source at the source
temperature.
Add components in the sequence indicated in Mixing
Order using 2 teaspoons for each pound or 1 teaspoon for
each pint of label rate per acre.
Always cap the jar and invert 10 cycles between compo-
nent additions.
When the components have all been added to the jar, let
the solution stand for 15 minutes. Evaluate the solution for
uniformity and stability. The spray solution should not have
free oil on the surface, or fine particles that precipitate to
the bottom, or thick (clabbered) texture. If the spray
 solution is not compatible, repeat the compatibility test with
the addition of a suitable compatibility agent. If the solution
is then compatible, use the compatibility agent as directed
on its label. If the solution is still incompatible, DO NOT mix
the ingredients in the same tank.
Mixing Order
Maintain constant agitation throughout mixing and
 application.
1. Water - Begin by agitating a thoroughly clean sprayer
tank 3/4 full of clean water.
2. Inductor - If an inductor is used, rinse it thoroughly after
each component has been added.
3. Products in PVA bags - Place any product contained
in water-soluble PVA bags into the mixing tank. Wait until
all water-soluble PVA bags have fully dissolved and the
product is evenly mixed in the spray tank before
 continuing.
4. Water-dispersible products (dry flowables, wettable
powders, suspension concentrates, or suspo- emulsions)
5. Water-soluble products
6. Emulsifiable concentrates (such as Outlook or oil
concentrate when applicable)

12
7. Water-soluble additives (such as AMS or UAN when
applicable)
8. Remaining quantity of water
Use Restrictions
• Maximum seasonal application rate - DO NOT apply
more than a total of 0.98 pound of active ingredient
dimethenamid-P (21 fl ozs of Outlook
® herbicide) per
acre per season in all labeled crops except corn, cotton,
sugar beet, and soybean. See Crop-specific
Information section for maximum seasonal application
rate in corn, cotton, sugar beet, and soybean.
• Preharvest Interval (PHI) - Refer to Crop-specific
Information for crop-specific preharvest intervals and
feeding and grazing restrictions.
• Outlook is not for sale, distribution, or use in Nassau and
Suffolk counties in New York State.
• DO NOT contaminate irrigation ditches or water used for
domestic purposes.
Use Precautions
• Emergency replanting (recropping) intervals
- If corn, dry bean, grain sorghum, peanut, or soybean
treated with Outlook are lost to adverse weather or for
other reasons, the area treated may be replanted to any
of those crops immediately, unless specified otherwise
in the Crop-Specific Information section of this label.
- If the original Outlook treatment was broadcast,
DO NOT make a second application of Outlook.
- If the original application was banded and the second
crop is planted in the row middles, a second band
application may be applied.
- If Outlook has been applied to sugar beets, table
beets, cotton, dry bulb onions, garlic, dry bulb shallots,
green onions, hops, perennial grass grown for seed,
horseradish, potato, sweet potato, tuberous and corm
vegetables, radish, rutabaga, turnip, pumpkin, or winter
squash and crop failure occurs because of adverse
weather or other reasons, replant ing (recropping) these
crops is not advised. If replanting a crop is necessary,
plant any of the following labeled crops (corn, dry bean,
grain sorghum, peanut, soybean) where soil application
of Outlook is registered.
• Stress - Application to crops under stress because of
lack of moisture, hail damage, flooding, herbicide injury,
mechanical injury, or widely fluctuating temperatures may
result in crop injury.
Crop Rotation Intervals
Refer to Table 3 to determine the proper interval between
Outlook application and the planting of rotational crops.
Determine the rotational crop interval for tank mix products
and use the most restrictive interval of all products applied.
Table 3. Rotational Crop Planting Intervals by
Outlook Application Rate
* Cover crops (winter, spring) may be planted after application of Outlook,
either inter-seeded into the current crop before harvest or after harvest of
the current crop. Depending on the sensitivity of the sown cover crop to
Outlook, stand establishment may be reduced. If cover crops are sown
for conservation purposes prior to a 4-month interval, DO NOT harvest
as a food or feed crop, or allow livestock to graze cover crops.
Crop-specific Information
Beet, Sugar
Outlook may be used as part of a weed management
 program in sugar beet.
Normal Timing
Apply Outlook after sugar beets have reached the 2-leaf
stage (at least 2 fully expanded true leaves) but before
sugar beets have exceeded the 8-leaf stage. Application at
2-leaf stage or later may result in temporary leaf injury.
Application made from preemergence up through
 cotyledon stage of beets may result in significant crop
injury including possible stand reduction.
Extended Timing
Apply Outlook after sugar beets have reached the 9-leaf
stage but before sugar beets have exceeded the 12-leaf
stage.
Refer to Table 2 for specific maximum application rates of
Outlook depending on soil type and organic matter
 content.
Outlook may be applied in a single application or two split
applications. If Outlook is applied only as a single applica-
tion, DO NOT exceed 21 fl ozs/A. If Outlook is applied in
two split applications, maintain a minimum of 14 days
between split applications. DO NOT exceed a seasonal
total of 24 fl ozs/A of Outlook. If two applications are
made, apply no more than 12 to 16 fl ozs/A during the first
application (applied during Normal Timing: 2 true-leaf to
8 true-leaf stage); then the remainder (8 to 12 fl ozs/A) of
the seasonal maximum rate during the second application
(applied during Extended Timing: 9-leaf to 12-leaf true-
leaf stage).
Crop
Outlook Use Rate
(fl ozs/A)
< 16 16 to 21
Rotational Crop Interval
(months after application)
Alfalfa 4 6
Canola (rapeseed) 4 6
Cotton 4 4
Peas (dry field, edible) 4 4
Small grains 4 4
Cover crops
(winter, spring)*
4 6
Other crops 6 9

13
Crop-specific Restrictions
• Harvest only mature beets and tops. 
• Preharvest Interval (PHI) for Normal Timing application:
60 days
• Preharvest Interval (PHI) for Extended Timing applica-
tion: 95 days 
Sugar Beet Tank Mixes
Application may be made alone or in tank mixtures with
other registered herbicides on sugar beet. Crop injury is
possible when tank mixing other herbicides as well as any
adjuvants such as methylated seed oils with Outlook
®
herbicide. Read and follow the applicable Crop-specific
Restrictions and Directions For Use on all products
involved in tank mixing. The most restrictive labeling applies
to tank mixes.
Beet, Table (Garden)
Outlook may be used as part of a weed management pro-
gram in table (garden) beet.
Apply Outlook after table beets have reached the 2-leaf
stage (at least 2 fully expanded true leaves) but before
table beets have exceeded the 6-leaf stage. 
Application at 2-leaf stage or later may result in temporary
leaf injury. Application made from preemergence up
through cotyledon stage of table beets may result in signifi-
cant crop injury including possible stand reduction.
A total maximum combined rate of 21 fl ozs/A of Outlook
may be applied on any soil type in a single growing season.
Refer to Table 2 for specific maximum application rates of
Outlook depending on soil type and organic matter
 content.
Outlook may be applied in single application or two split
applications (such as micro-rate programs). If two applica-
tions are made, maintain a minimum of 14 days between
split applications. If two applications are made, apply 1/2 to
2/3 of rate during first application; then the remainder of
rate during second application. If two applications are
made, DO NOT exceed a total of 21 fl ozs/A of Outlook
per season.
Crop-specific Restrictions
• Harvest only mature beets and tops. 
• Preharvest Interval (PHI) for beets and tops: 60 days
Field Corn (grain, seed, silage),
Fresh Sweet Corn, Popcorn
Use not permitted in California on sweet corn.
Outlook may be applied preplant surface, preplant incor-
porated, preemergence, or postemergence to corn up to
12-inches tall. Corn in this label refers to field corn grown
for grain, seed, or silage; fresh sweet corn; and popcorn.
Before applying to seed corn, sweet corn, or popcorn, ver-
ify with your local seed company (supplier) the Outlook
selectivity on your inbred line or hybrid to avoid potential
injury.
Outlook may also be applied at layby to field corn, seed
corn, and popcorn. Layby applications are made when
corn is greater than 12-inches tall but before it is greater
than 36-inches tall. For layby application for control of late -
season germinating weeds, apply before weeds emerge
from soil or in combination with a herbicide(s) and/or culti-
vation that controls emerged weeds. For best
performance, direct application beneath the corn canopy.
Outlook may be applied in a single application or two split
applications.
Refer to Table 2 for specific maximum application rates of
Outlook depending on soil type and organic matter
 content.
If Outlook is applied in two split applications, maintain a
minimum of 14 days between split applications, and
DO NOT exceed a seasonal total of 24 fl ozs/A of
Outlook. If two applications are made, apply no more than
8 to 16 fl ozs/A during the first application (applied
 preplant, preemergence, or postemergence); then apply
the remainder (8 to 16 fl ozs/A) of the seasonal maximum
rate during the second application (postemergence, layby).
Crop-specific Restrictions
• Corn may be grazed or fed to livestock 40 days or more
after application of Outlook.
• Preharvest Interval (PHI) for sweet corn ears: 50 days
• DO NOT make layby application of Outlook to sweet
corn.
Corn Tank Mixes
Refer to the tank mix product labels to confirm the respec-
tive tank mix products are registered for use on specific
corn types. Not all corn products are registered for use on
seed corn, popcorn, and sweet corn.
Glyphosate-resistant Corn Programs
Outlook may be used preemergence and postemergence
to glyphosate-resistant corn hybrids. Refer to a glyphosate
product label for specific weeds controlled post emergence.
Sequential Program
Outlook may be applied preemergence at 12 fl ozs/A in a
planned preemergence followed by glyphosate postemer-
gence sequential program.
Postemergence Tank Mix Program
Outlook may be applied at 12 fl ozs/A in a postemergence
tank mix with glyphosate to corn up to 12-inches tall.
Layby application may also be made when corn is greater
than 12-inches tall but before it is greater than 36-inches
tall. Drop nozzles are required when corn is 30-inches to
36-inches tall. Labeled use rates for this tank mix are listed
in Table 4. This tank mix with glyphosate should be applied
when weeds are 2 inches to 4 inches in height and before
weed height and/or density become competitive with the
crop.

14
Table 4. Broadcast Application Rate per Acre
Cotton
Use not permitted in California on cotton.
Outlook may only be applied postemergence to cotton for
residual weed control. Before applying to cotton, verify with
your local seed company (supplier) the selectivity of
Outlook on your variety to avoid potential injury.
Use of Outlook may result in temporary growth suppres-
sion in cotton if extreme conditions of high rainfall and
extended periods of water-saturated soil occur during cot-
ton germination or early seedling development.
Application Rate and Timing
Outlook may be applied in either a single postemergence
application (see Single Application section) or in sequen-
tial postemergence applications (see Sequential
Applications section).
Early Postemergence Application
Outlook must be applied before weed seedling
emergence or in a tank mix with products registered for
use on cotton that control the emerged weeds. For effec-
tive residual activity, rainfall, sprinkler irrigation, or shallow
mechanical incorporation after application is required to
move this product into the upper soil surface where weed
seeds germinate.
Outlook will provide residual control of weeds germinating
after application. Weeds that are emerged at time of appli-
cation must be controlled with cultivation, or a tank mix or
sequential application of another herbicide labeled for
postemergence weed control in cotton.
Outlook application to emerged cotton may result in tem-
porary leaf burn, spotting, and/or stunting, but a reduction
in cotton yield is not expected.
Adjuvants may be applied with Outlook when making early
postemergence application.
Single application. Apply Outlook at up to 21 fl ozs/A as
a broadcast spray to cotton from first true leaf stage to the
mid-bloom stage (i.e. two weeks after R1 initial bloom
stage). DO NOT apply more than 21 fl ozs/A of Outlook in
a single application.
Sequential application. Outlook may be applied as split
applications when both the initial and sequential application
is made early postemergence. With the initial application,
apply Outlook very early postemergence (typically from
first true leaf stage to 6 to 10 leaf stage) at 12 to 18 fl ozs/A
as a broadcast spray to cotton. For the sequential applica-
tion, apply Outlook early postemergence (up to the
mid-bloom stage, i.e. two weeks after R1 initial bloom
stage) at 13 to 19 fl ozs/A as a broadcast spray to cotton.
Sequential applications must be separated by at least
14 days. DO NOT apply more than 31 fl ozs/A of Outlook
from early postemergence applications.
Crop-specific Restrictions
• DO NOT apply preplant surface, preplant incorporated,
or preemergence in cotton.
• DO NOT apply more than a maximum cumulative
amount of 31 fl ozs/A of Outlook per year.
• There is no required (preharvest) interval between a
postemergence application of Outlook and the harvest
of cotton. 
• Cotton gin byproducts may be fed to livestock. 
Cotton Tank Mixes
Tank mixing Outlook with other emulsifiable concentrate
(EC) formulated products may enhance potential for cotton
injury response.
Dry Bean
Use not permitted in California on dry bean.
Outlook may be applied preplant surface, preplant incor-
porated, preemergence, or early postemergence (first to
third trifoliate stage) to dry bean classes (black turtle soup,
cranberry, dry lima, great northern, navy, pink, pinto, red
kidney, red Mexican, and small whites). Outlook may only
be applied preplant surface or preemergence to garbanzo
beans and lentils. Outlook is not registered for use in suc-
culent beans, succulent bean varieties grown for seed, or
cowpeas.
Before applying Outlook to dry beans, verify with your
local seed company (supplier) the selectivity of Outlook on
your specific dry bean class and variety to help avoid
potential injury to sensitive classes or varieties.
If extreme conditions of high rainfall and extended periods
of water-saturated soil occur during dry edible bean germi-
nation or early seedling development, Outlook use may
result in temporary growth suppression. This suppression
will not reduce dry edible bean yield. Outlook use
 postemergence may occasionally result in some temporary
spotting or browning of dry bean leaves and stunting, but a
reduction in dry bean yield is unexpected. Postemergence
tank mixtures with other crop protection products or
 adjuvants may significantly enhance this effect. Depending
on growing conditions, recovery from this injury begins
immediately but may take several weeks for dry beans to
recover completely.
Refer to Table 2 for specific maximum application rates of
Outlook depending on soil type and organic matter
 content.
Outlook may be applied in a single application of up to
21 fl ozs/A or used in split applications of 10 to 14 fl ozs/A
of Outlook applied initially, and the remaining 7 to
11 fl ozs/A of Outlook in the sequential application.
Soil Texture
Group
Outlook® herbicide
(fl ozs) glyphosate
Coarse 10 to 12 labeled rate
Medium 12 to 14 labeled rate
Fine 12 to 16 labeled rate

15
DO NOT exceed a total of 21 fl ozs/A of Outlook®
 herbicide per season. 
Additional restrictions specific to dry beans are to use a
maximum of 12 fl ozs/A of Outlook on coarse soils with
organic matter less than 1.5% for soil applications made
before crop emergence.
Crop-specific Restrictions
• DO NOT apply Outlook early postemergence to dry
beans grown in the states of Washington and Oregon
(EXCEPTION: Malheur county).
• DO NOT apply Outlook early postemergence by chemi-
gation to dry beans grown in Idaho or Malheur County,
Oregon.
• Preharvest Interval (PHI): 70 days
Dry Bean Tank Mixes
The following herbicide products may only be applied
sequentially with Outlook:
• Dual II Magnum® herbicide
• Dual Magnum® herbicide
Dry Bulb Onions, Garlic, Dry Bulb Shallots
Outlook may be used as part of a weed management pro-
gram in dry bulb onions, garlic, and dry bulb shallots grown
in muck soils, high organic soils, and in mineral soils.
Apply Outlook after dry bulb onions, garlic, and dry bulb
shallots have reached the 2 true-leaf stage until a minimum
of 30 days before harvest. Application made before 
2 true-leaf stage may result in significant crop injury includ-
ing possible stand reduction. If applications are made to
transplanted dry bulb onions, garlic, and dry bulb shallots,
DO NOT apply until transplants are in the ground and soil
has settled around transplants with several days to recover.
Outlook may be applied in a single application of up to
21 fl ozs/A or used in split applications of 10 to 14 fl ozs/A
of Outlook applied initially, and the remaining 7 to
11 fl ozs/A of Outlook in the sequential application. If split
applications are made, maintain a minimum of 14 days
between sequential applications. DO NOT apply more than
a total of 21 fl ozs/A of Outlook in a single growing
 season.
A total maximum combined rate of 21 fl ozs/A of Outlook
may be applied on any soil type in a single growing season.
Refer to Table 2 for specific maximum application rates of
Outlook depending on soil type and organic matter
 content.
Crop-specific Restrictions
• Preharvest Interval (PHI): 30 days
Dry Bulb Onions, Garlic, Dry Bulb Shallots
Tank Mixes
Crop injury is possible when tank mixing other herbicides
as well as any adjuvants such as methylated seed oils with
Outlook. Read and follow the applicable Crop-specific
Restrictions and Directions For Use on all products
involved in tank mixing. The most restrictive labeling applies
to tank mixes.
Fallow
Outlook may be used as a residual treatment to control
listed weeds before they germinate at the beginning of the
fallow period. Specific rotational crop planting intervals
must be observed between an application of Outlook and
planting of the following crops (see Crop Rotation
Intervals section).
Application Rate and Timing
Apply Outlook as a broadcast spray at up to 21 fl ozs/A
before weeds emerge for best product performance.
Split applications may be made with a minimum of 30 days
between applications; but DO NOT exceed the maximum
seasonal cumulative amount of 21 fl ozs/A of Outlook per
cropping season.
Use not permitted in California on green onions.
Outlook may be used as part of a weed management pro-
gram in green onions grown in muck soils, high organic
soils, and mineral soils. Outlook may only be applied by
ground (broadcast) application.
Apply Outlook after green onions have reached the 2 true-
leaf stage until a minimum of 30 days before harvest.
Application made before 2 true-leaf stage may result in sig-
nificant crop injury including possible stand reduction. If
applications are made to transplanted green onions,
DO NOT apply until transplants are in the ground and soil
has settled around transplants with several days to recover.
Outlook may be applied in a single application of up to
21 fl ozs/A or used in split applications of 10 to 14 fl ozs/A
of Outlook applied initially, and the remaining 7 to
11 fl ozs/A of Outlook in the sequential application. If split
applications are made, maintain a minimum of 14 days
between sequential applications. DO NOT apply more than
a total of 21 fl ozs/A of Outlook in a single growing
 season.
Crop-specific Restrictions
• Preharvest Interval (PHI): 30 days
Green Onions
(Leeks, Spring onions or 
Scallions, Japanese bunching onions,
Green shallots or Eschalots)

Green Onion Tank Mixes
Outlook® herbicide application may be made before, in
tank mixture, or after use of registered herbicides for poste-
mergence use in green onions.
Crop injury is possible when tank mixing herbicides as well
as any adjuvants such as methylated seed oils with
Outlook. Read and follow the applicable Crop-specific
Restrictions and Directions For Use on all products
involved in tank mixing. The most restrictive labeling applies
to tank mixes.
Hops
Use not permitted in California on hops.
Outlook may be used as part of a weed management pro-
gram in baby (first year planting) and established hops.
Outlook may only be applied by ground (banded)
 application (including postemergence-directed). Contact
with hop foliage or cones by spray mixture or drift may
cause injury. Apply Outlook preemergence to weeds when
hops are in the dormant or early vegetative stages of
growth.
Outlook may only be applied in single application.
Outlook has not been tested on hops grown in all soil tex-
tures. Refer to Table 2 for soil texture group descriptions
and appropriate application rates. BASF recommends
 testing Outlook on a small portion of the target crop to
confirm safety in the local soil type.
Depending on application timing, Outlook may negatively
impact growth of cover crops planted in the fall after
 harvest.
Crop-specific Restrictions
• DO NOT apply to hops by air or through any type of irri-
gation system.
• DO NOT apply more than 21 fl ozs/A of Outlook per
 season.
• Preharvest Interval (PHI): 60 days
Tank Mixes
Tank mixes with other herbicides, fungicides, insecticides,
and fertilizers are not advised when using this product in
hops.
Peanut
Use not permitted in California on peanut.
Outlook may be applied preplant surface, preplant incor-
porated, preemergence, or postemergence (up to 80 days
before harvest) alone or in tank mix combination. Use high-
er rates (16 to 21 fl ozs/A of Outlook) for improved control
or suppression of difficult weeds like yellow nutsedge,
Florida beggarweed, eclipta, common ragweed, and other
broadleaf species.
Refer to Table 2 for specific maximum application rates of
Outlook depending on soil type and organic matter
 content.
Outlook may be applied in a single application of up to
21 fl ozs/A or used in split applications of 10 to 14 fl ozs/A
of Outlook applied initially, and the remaining 7 to
11 fl ozs/A of Outlook in the sequential application.
DO NOT apply more than 21 fl ozs/A of Outlook per
 season.
Crop-specific Restrictions
• Peanut hay or straw may be grazed or fed to livestock
80 days or more after application of Outlook.
Perennial Grass grown for Seed
For use on perennial grass grown for seed only in
states west of the Mississippi River.
Outlook may be used as part of a weed management
 program in established stands of cool- season and warm-
 season perennial grass grown for seed. Grass seed crops
must have been established for at least one year or had at
least one seed crop harvested before Outlook use.
The grass seed screenings remaining after processing and
grass straw remaining after seed harvest may be grazed by
or fed to livestock.
Outlook applied as directed will provide preemergence
control or suppression of volunteer seedlings from previous
grass seed crops in addition to many annual grass weeds,
annual broadleaf weeds, and sedge listed in Table 1.
In cool-season perennial grass, apply 14 to 21 fl ozs/A of
Outlook to postharvest grass during regrowth in the fall or
spring before emergence of targeted weeds. Outlook may
be applied in a sequential use program with other
 herbicides that control emerged weeds. Application to
perennial ryegrass and fine fescue stands under stress may
cause crop injury.
In warm-season perennial grass, apply 14 to 21 fl ozs/A of
Outlook to postharvest grass during the fall, or during win-
ter dormancy, or after the first seed harvest/cutting.
DO NOT apply to warm-season perennial grass after
greenup in the spring before the first seed harvest/cutting.
Outlook may be applied in a sequential use program with
other herbicides that control emerged weeds.
In both cool-season and warm- season perennial grass, use
the higher rate in the rate range where more dense
 infestations of targeted annual grass weeds, annual
broadleaf weeds, or sedge are expected. Grass straw from
the previous harvest must be removed, burned, or evenly
spread before Outlook application or reduced weed con-
trol may result.
For effective control or suppression of annual grass weeds,
annual broadleaf weeds, sedge, or volunteer seedlings
from previous grass seed crops, this product must be
moved into the upper soil surface where weed seeds
 germinate by rainfall or irrigation before weed emergence.
16

17
Application made in periods of cold temperature that tem-
porarily limit normal crop growth or in extended cold
 temperature periods that initiate winter dormancy in grass
crops may result in crop injury.
Outlook
® herbicide may be tank mixed with other herbi-
cides labeled for use in perennial grass grown for seed.
BASF recommends testing Outlook tank mixes on a small
portion of the target crop to determine if damage is likely to
occur. Physical incompatibility, reduced weed control,
or crop injury may result from mixing Outlook with
other pesticides (fungicides, herbicides, insecticides,
or miticides), additives, or fertilizers. Subsequent appli-
cation of postemergence herbicides may cause crop injury.
Consult with your local BASF dealer regarding local tank
mix options.
Crop-specific Restrictions
• DO NOT apply a total of more than 21 fl ozs/A of
Outlook per growing season.
• From treated fields of cool-season perennial grass, forage
and hay may be grazed by or fed to livestock 60 days
after application.
• From treated fields of warm-season perennial grass, for-
age and hay may be grazed by or fed to livestock 
30 days after application.
Potato, Sweet Potato, Horseradish 
Use not permitted on horseradish and sweet potato
in California.
Outlook may be used as part of a weed management
 program in horse radish, potato, and sweet potato.
In potato and sweet potato, apply Outlook preemergence
(after planting or after drag-off). In horseradish, apply
Outlook postemergence from the 2-leaf stage to the 8-leaf
stage of plant development. Outlook may only be applied
in a single application in horseradish, potato, and sweet
potato.
In cold and wet growing conditions, Outlook application
may result in delayed emergence or early season stunting
of horseradish, potato, and sweet potato.
Outlook use can cause crop injury to sweet potatoes.
Apply Outlook preemergence only. Apply Outlook so as
not to come into contact with developing tubers. The
option of applying Outlook for weed control rather than
crop injury should be based on potential crop loss because
of weed infestations compared to potential loss from crop
injury. Test Outlook on a portion of the crop to determine if
the use of Outlook is suitable for the intended results.
Refer to Table 2 for specific maximum application rates of
Outlook depending on soil type and organic matter con-
tent. DO NOT exceed the specified rate by soil type and
organic matter content in a single application.
Crop-specific Restrictions
• Preharvest Interval (PHI): 40 days
Sorghum (Grain)
Outlook may be used preplant surface, preplant incorpo-
rated, preemergence, or postemergence to grain sorghum
up to 12-inches tall. Single or split application may be
used.
Outlook is not registered for use on sweet or forage
sorghum.
All Outlook applications must only be made to sorghum
seed that has been properly treated by the seed company
with an approved chloroacetamide herbicide safener or
severe injury may occur.
Under high soil moisture or cool conditions, Outlook appli-
cation may cause temporary stunting or leaf wrapping of
sorghum. Sorghum will normally outgrow these symptoms
in 10 to 14 days.
For best performance, make preemergence surface
 application within 5 days of the last preplant tillage. If
weeds have emerged, apply Outlook with herbicides to
control emerged vegetation.
Refer to Table 2 for specific maximum application rates of
Outlook depending on soil type and organic matter
 content.
Crop-specific Restrictions
• Sorghum forage may be grazed or fed to livestock
60 days or more after application of Outlook. 
• Preharvest Interval (PHI) for grain and fodder: 80 days 
• DO NOT apply preplant incorporated in California.
Soybean
Use not permitted in California on soybean.
Outlook may be applied preplant surface, preplant incor-
porated, preemergence, or postemergence [from
 emergence (cracking stage) to fifth-trifoliate leaf stage] to
soybean.
If Outlook is applied preplant incorporated, incorporation
must be uniform and shallow (upper 1 to 2 inches of soil).
Deeper incorporation may reduce weed control or increase
the potential for crop injury. Preplant incorporated
treatments are not for use on coarse soils with less than
1.5% organic matter.
If extreme conditions of high rainfall and extended periods
of water-saturated soil occur during soybean germination
or early seedling development, Outlook use may result in
temporary growth suppression.
Temporary soybean burn and/or stunting may occur with
postemergence applications of Outlook. Tank mixtures
with other herbicides not listed in the Soybean Tank
Mixes section and/or spray adjuvants may increase the
level of crop injury. Crop injury is typically transient and has
not resulted in reduced soybean yield potential.
Outlook may be applied in a single application or two split
applications.

18
Refer to Table 2 for specific maximum application rates of
Outlook® herbicide depending on soil type and organic
matter content.
If Outlook is applied only as a single application, DO NOT
apply more than 21 fl ozs/A. If Outlook is applied in two
split applications, maintain a minimum of 14 days between
split applications, and DO NOT exceed a seasonal total of
24 fl ozs/A of Outlook. If two applications are made, apply
no more than 8 to 16 fl ozs/A during the first application
(applied preplant, preemergence, or postemergence); then
apply the remainder (8 to 16 fl ozs/A) of the seasonal maxi-
mum rate during the second application (postemergence).
Crop-specific Restrictions
• DO NOT graze or feed forage, hay, or straw to livestock.
Tuberous and Corm Vegetables
Use not permitted in California on tuberous and corm
vegetables.
Outlook may be used as part of a weed management pro-
gram in the following tuberous and corm vegetables:
 arracacha, arrowroot, Chinese and Jerusalem artichoke,
edible canna, bitter and sweet cassava, root chayote,
chufa, dasheen, ginger, leren, tanier, turmeric, yam bean,
true yam.
In tuberous and corm vegetables, apply Outlook pre-
emergence (after planting or after drag-off).
In cold and wet growing conditions, Outlook application
may result in delayed emergence or early season stunting
of tuberous and corm vegetables.
Outlook may only be applied in a single application in
tuberous and corm vegetables.
Refer to Table 2 for specific maximum application rates of
Outlook depending on soil type and organic matter
 content.
Crop-specific Restrictions
• Preharvest Interval (PHI): 40 days
Turnip, Radish, Rutabaga
Outlook may be used as part of a weed management
 program in radish, rutabaga, and turnip.
Outlook may only be applied by ground (broadcast)
application.
Apply Outlook after rutabaga and turnip have reached the
2-leaf stage (at least 2 fully expanded true leaves) but
before rutabaga and turnip have exceeded the 8-leaf
stage. Application at 2-leaf stage or later may result in tem-
porary leaf injury. Application made from preemergence
through cotyledon stage of rutabaga and turnip may result
in significant crop injury including possible stand reduction.
Apply Outlook after radish has reached the 2-leaf stage
(at least 2 fully expanded true leaves) but before radish
has exceeded the 4-leaf stage. Application at 2-leaf to 
4-leaf stage may result in temporary leaf injury. Application
made from preemergence through cotyledon stage of
radish may result in significant crop injury including possible
stand reduction.
Outlook may only be applied in single application.
Refer to Table 2 for specific maximum application rates of
Outlook depending on soil type and organic matter
 content.
Crop-specific Restrictions
• DO NOT apply to radish, rutabaga, and turnip by air or
through any type of irrigation system.
• DO NOT apply more than 21 fl ozs/A of Outlook per
 season.
• Harvest only mature tops and roots of radish, rutabaga,
and turnip. 
• Preharvest Interval (PHI) for rutabaga and turnip tops:
14 days
• Preharvest Interval (PHI) for rutabaga and turnip roots:
40 days
• Preharvest Interval (PHI) for radish tops and roots:
21 days 
Tank Mixes
Tank mixes with other herbicides or insecticides are not
advised when applying this product in radish, rutabaga,
and turnip.
Winter Squash, Pumpkin
For use only in Oregon and Washington. 
Outlook may be used as part of a weed management
 program in pumpkin and winter squash
(Golden Delicious variety only).
Outlook may only be applied by ground (broadcast)
application.
Apply Outlook as a preemergence surface application.
Broadcast the treatment uniformly to the soil surface after
planting and before crop and weed emergence. If extreme
conditions of high rainfall and extended periods of water-
saturated soil occur during pumpkin or winter squash
germination or early seedling development, Outlook use
may result in growth suppression, which may reduce
yields.
Outlook may only be applied in single application.
Apply a minimum of 12 to 14 fl ozs/A of O utlook on soils
with less than 3% organic matter. Apply a minimum of
16 to 18 fl ozs/A on soils with greater than 3% organic
matter. DO NOT apply more than 21 fl ozs/A of Outlook
on any soil in a single application.

19
Crop-specific Restrictions
• DO NOT apply to pumpkin or winter squash by air or
through any type of irrigation system.
• DO NOT apply when conditions favor drift to adjacent
susceptible vegetation.
• DO NOT apply more than 21 fl ozs/A of Outlook®
 herbicide per year in pumpkin or winter squash.
• Preharvest Interval (PHI): 90 days
Tank Mixes
Tank mixes with other herbicides or insecticides are not
advised when using this product in pumpkin or winter
squash.

20
Outlook is a registered trademark of BASF.
Dual II Magnum and Dual Magnum are registered trade-
marks of a Syngenta Group Company.
Dual Magnum® herbicide (s-metolachlor),
EPA Reg. No. 100-816
Dual II Magnum® herbicide (s-metolachlor),
EPA Reg. No. 100-818
© 2019 BASF Corporation
All rights reserved.
007969-00156.20180131b.NVA 2018-04-086-0016
Supersedes: NVA 2017-04-086-0063
Supplemental: NVA 2018-04-086-0015
BASF Corporation
26 Davis Drive
Research Triangle Park, NC 27709
Conditions of Sale and Warranty
The Directions For Use of this product reflect the
 opinion of experts based on field use and tests. The
 directions are believed to be reliable and must be followed
carefully. However, it is impossible to eliminate all risks
inherently associated with the use of this product. Crop
injury, ineffectiveness or other unintended consequences
may result because of such factors as weather conditions,
presence of other materials, or use of the product in a
manner inconsistent with its labeling, all of which are
beyond the control of BASF CORPORATION (“BASF”) or
the Seller. To the extent consistent with applicable law, all
such risks shall be assumed by the Buyer.
BASF warrants that this product conforms to the chemical
description on the label and is reasonably fit for the
 purposes referred to in the Directions For Use, subject
to the inherent risks, referred to above.
TO THE EXTENT CONSISTENT WITH APPLICABLE
LAW, BASF MAKES NO OTHER EXPRESS OR
IMPLIED WARRANTY OF FITNESS OR
 MERCHANTABILITY OR ANY OTHER EXPRESS OR
IMPLIED WARRANTY.
TO THE EXTENT CONSISTENT WITH APPLICABLE
LAW, BUYER’S EXCLUSIVE REMEDY AND BASF’S
EXCLUSIVE LIABILITY, WHETHER IN CONTRACT,
TORT, NEGLIGENCE, STRICT LIABILITY, OR
 OTHERWISE, SHALL BE LIMITED TO REPAYMENT
OF THE PURCHASE PRICE OF THE PRODUCT.
TO THE EXTENT CONSISTENT WITH APPLICABLE
LAW, BASF AND THE SELLER DISCLAIM ANY
 LIABILITY FOR CONSEQUENTIAL, EXEMPLARY,
SPECIAL OR INDIRECT DAMAGES RESULTING
FROM THE USE OR HANDLING OF THIS PRODUCT.
BASF and the Seller offer this product, and the Buyer and
User accept it, subject to the foregoing Conditions of
Sale and Warranty which may be varied only by
 agreement in writing signed by a duly authorized
representative of BASF.
1108

BASF Corporation 
26 Davis Drive, Research Triangle Park, NC 27709 
 
Supplemental Label 
 
Increased rate for early postemergence sequential applications in cotton 
This supplemental label expires November 30, 2022, and must not be used or distributed after this date. 
Active Ingredient*: 
dimethenamid-P: (S)-2-chloro-N-[(1-methyl-2-methoxy)ethyl]- 
N-(2,4-dimethyl-thien-3-yl)-acetamide ............................................................................................................. 63.9% 
Other Ingredients**: ....................................................................................................................................... 36.1% 
Total: ............................................................................................................................................................... 100.0% 
 * Contains 6.0 pounds of active ingredient per gallon 
** Contains petroleum distillates 
 
EPA Reg. No. 7969-156 
KEEP OUT OF REACH OF CHILDREN 
WARNING/AVISO 
 
Directions For Use 
• It is a violation of federal law to use this product in a 
manner inconsistent with its labeling. 
• The supplemental labeling and the entire 
Outlook® herbicide container label, EPA Reg. 
No. 7969-156, must be in possession of the user at 
the time of application. 
• Read the label affixed to the container for Outlook 
before applying. 
• Use of Outlook according to this labeling is subject 
to the use precautions and restrictions imposed by 
the label affixed to the container for Outlook. 
Product Information 
Outlook is a selective preemergence herbicide for 
controlling annual broadleaf weeds, annual grass 
weeds, and sedges. Refer to the Outlook container 
label for a complete list of weeds controlled. 
 
 
 
Application Information 
Early Postemergence Application
Outlook may be applied as split applications when 
both the initial and sequential application is made early 
postemergence. With the initial application, apply 
Outlook very early postemergence (typically from first 
true leaf stage to 6 to 10 leaf stage) at 12 to 18 fl ozs/A 
as a broadcast spray to cotton. For the sequential 
application, apply Outlook early postemergence (up to 
the mid-bloom stage, i.e. two weeks after R1 initial 
bloom stage) at 13 to 19 fl ozs/A as a broadcast spray 
to cotton. Sequential applications must be separated by 
at least 14 days. DO NOT apply more than 31 fl ozs/A 
of Outlook from early postemergence applications. 
Crop-specific Restrictions 
• DO NOT apply more than a maximum cumulative 
amount of 31 fl ozs/A of Outlook per year. 
• DO NOT apply preplant surface, preplant 
incorporated, or preemergence in cotton. 
• There is no required (preharvest) interval between a 
postemergence application of Outlook and the 
harvest of cotton. 
• Cotton gin byproducts may be fed to livestock. 
 
Dimethenamid-P Group 15 Herbicide 
 
11/29/2019
7969-156

2 
Conditions of Sale and Warranty 
The Directions For Use of this product reflect the 
opinion of experts based on field use and tests. The 
directions are believed to be reliable and must be 
followed carefully. However, it is impossible to 
eliminate all risks inherently associated with the use 
of this product. Crop injury, ineffectiveness or other 
unintended consequences may result because of 
such factors as weather conditions, presence of 
other materials, or use of the product in a manner 
inconsistent with its labeling, all of which are 
beyond the control of BASF CORPORATION 
(“BASF”) or the Seller. To the extent consistent with 
applicable law, all such risks shall be assumed by 
the Buyer. 
BASF warrants that this product conforms to the 
chemical description on the label and is reasonably 
fit for the purposes referred to in the Directions For 
Use, subject to the inherent risks, referred to above. 
TO THE EXTENT CONSISTENT WITH 
APPLICABLE LAW, BASF MAKES NO OTHER 
EXPRESS OR IMPLIED WARRANTY OF 
FITNESS OR MERCHANTABILITY OR ANY 
OTHER EXPRESS OR IMPLIED WARRANTY. 
TO THE EXTENT CONSISTENT WITH 
APPLICABLE LAW, BUYER’S EXCLUSIVE 
REMEDY AND BASF’S EXCLUSIVE LIABILITY, 
WHETHER IN CONTRACT, TORT, NEGLIGENCE, 
STRICT LIABILITY, OR OTHERWISE, SHALL BE 
LIMITED TO REPAYMENT OF THE PURCHASE 
PRICE OF THE PRODUCT. 
TO THE EXTENT CONSISTENT WITH 
APPLICABLE LAW, BASF AND THE SELLER 
DISCLAIM ANY LIABILITY FOR 
CONSEQUENTIAL, EXEMPLARY, SPECIAL OR 
INDIRECT DAMAGES RESULTING FROM THE 
USE OR HANDLING OF THIS PRODUCT. 
BASF and the Seller offer this product, and the 
Buyer and User accept it, subject to the foregoing 
Conditions of Sale and Warranty which may be 
varied only by agreement in writing signed by a duly 
authorized representative of BASF. 
1108 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
Outlook is a registered trademark of BASF. 
 
 
© 2019 BASF Corporation 
All rights reserved. 
 
007969-00156.20180131b.NVA 2018-04-086-0015 
 
BASF Corporation 
26 Davis Drive 
Research Triangle Park, NC 27709