crop-chem-docs/corpus/epa_ppls/228-414.md

# RIVERDALE VETERAN 3010 HERBICIDE

- EPA Reg No: **228-414**
- Registrant: NUFARM AMERICAS, INC.
- Signal word: Danger
- Active ingredients: Dicamba, dimethylamine salt (12.4%); 2,4-D, dimethylamine salt (35.7%)
- Label accepted: 2008-07-09
- Source PDF: https://www3.epa.gov/pesticides/chem_search/ppls/000228-00414-20080709.pdf

---
UNITED STATES ENVIRONMENTAL PROTECTION AGENCY 
WASHINGTON, D.C. 20460 
Theodore D. Head 
Nufann Americas Inc. 
150 Harvester Drive, Suite 200 
Burr Ridge, IL 60527 
Dear.Mr. Head: 
JUL 9 2008 
SUBJECT: RED Label Amendment2,4-D 
Riverdale Veteran 3010 
EPA Registration No. 228-414 
OFFICE OF 
PREVENTION, PESTICIDES AND 
TOXIC SUBSTANCES 
The amendment referred to above, submitted in connection with registration 
under the Federal Insecticide, Fungicide and Rodenticide Act (FIFRA), as amended is 
acceptable with the following provisions: 
1) Per the combined 2,4-DlDicamba label table, the PPE section must be revised to read: 
"Some materials that are chemical-resistant. ... 
All mixers, loaders, applicators, flaggers, and other handlers must wear: 
-Long sleeved shirt and long pants, 
-Shoes and socks, 
-Goggle or face shield, 
-Chemical-resistant gloves (except for applicators usinggroundboom equipment, pilots 
and flaggets and. 
-Chemical-resistant apron when mixing, loading, cleaning up spills or equipment, or 
otherwise exposed to the concentrate. . 
See engineering controls for additional requirements." 
2) The mechanical transfer engineering control text is no longer needed and may be 
deleted from the label. . 
3) The following text must be added to the engineering control section ofthe label: 
I 
~\

"Pilots must use an enclosed cockpit that meets the requirements listed in the WPSfor 
agricultural pesticides [40CFR 170.240(d)(6)." 
4) The text "except as noted on appropriate lab~ls" should be deleted from the second 
sentence of the Environmental Hazard section. 
5) Perthe combined 2,4-DlDicamba RED label table, the early entry PPE must be 
revised to read: 
"Coveralls worn over short sleeved shirt and short pants, 
Cpemical-resistant footwear plus socks, 
Chemical-resistant gloves made of any waterproof material, 
. Chemical-resistant headgear for overhead exposure, 
Protective eyewear." 
6) The text "For turf and industrial use" appearing in the entry restriction text in the 
Non-Agricultural Use Requirements box must be deleted fr9m the label. 
7) The following revisions are needed to the directions for use: 
Sugarcane: 
. . . 
Per the revised picamba RED label table, a PHI of 87 days must be added to the label for 
sugarcane. 
Sorghum: 
Per the revised Dicamba RED label table, a PHI of 30 days must be' added to the label for 
sorghum grain and fodder. 
Industrial Weed and Brush Control, Conservations Reserve Programs (CRP) and 
General Farmstead (Page 8 of label): 
-Because the RED requires different rate restrictions for noncropland sites (Industrial 
Weed and Brush Control and General Farmstead) and for Pasture and Rangeland 
(including CRP), the CRP directions for use and rate restrictions should be moved to 
Page 10 of the label. 
The following rate restrictions must be added to the noncropland section of the label and 
any conflicting text must be deleted from the label: 
"N oncropland: 
Postemergence (annual and perennial weeds: 
Limited to 2 applications per year. 
Maximum of 2 lbs ae per acre per application. 
Minimum of 30 days between applcations.

( 
Postemergence (woody plants): 
Limited to 1 application per year. 
Maximum of 4lbs ae per acre per year." 
Pasture and Rangeland and Grass: 
-Rates in excess of 1.0 lb ae per acre per application are not allowed to treat susceptible 
annual and biennial broadleafweeds in.CRP pasture and rangeland. The label must be 
revised to clarify this issue. 
Per the revised Dicamba RED label table, a PHI of 7 days must be added to the label for 
grass hay. 
Wheat: 
The preharvest rate of up to 2 pints of product (.716Ib ae of2,4-D) per acre per 
application exceeds the maximum allowable preharvest rate for 2,4-Drate ofO.5lb ae per 
acre per application. The label must be revised. 
Per the revised Dicamba RED label table, a PHI of 7 days must be added to the label for 
wheat grain. ' 
Rights-of-Way (including roadways, utility, railroad, highway, pipeline, and rights­
of-way that run through pastures and rangeland), utility facilities (including 
substations, tankfarms, pumping stations, and parking and storage areas), 
nonirrigated ditchbanks, and general farmstead: 
The word "ditchbank," an aquatic use, must be revised to read "ditches" as allowed in the 
2,4-D/Dicamba RED combined label table. 
The text "Do not apply more than 5 Y2 quarts of product (3.9Ibs ae of2,4-D) per treated 
acre" for treatment of herbaceous broadleafweeds in noncrop areas exceeds the 
allowable rate of2.0 lbs ae of2,4-D per acre per application. The label must be revised. 
This rate is only allowed for treatment of woody plants. 
8) Add the following statement to the labeling: 
"Use of this product in certain portions of California, Oregon and Washington is . 
subject to the January 22,2004 Order for injunctive relief in Washington Toxics 
Coalition, et al. v. EPA, COl-0132C, (W.D. WA). For further information, please refer to 
EPA Web Site: http://www.epa.gov/espp. 
~\

( ( 
Submit one (1) copy of your final printed labeling before you release the product 
for shipment. A stamped copy of the labeling is enclosed for your records. Please note 
that final product reregistration cannot be considered until after all active ingredients in . 
this product are eligible for reregistration. 
Enclosure 
Sincerely yours, 
Joanne I. Miller 
Product Manager (23) 
Herbicide Branch 
Registration Division (7S0SP)

VETERAN®3010 
HERBICIDE 
. . . 
For the Control of Brush and Broadleaf Weeds on Rights-of-Way, Roadways, Utility, Railroad, Hlghv't'¥i 
Pipeline, and Rights-of-Way that run through Pastures and Rangeland, Forest Brush, Fence Rows, N,)"l­
Irrigation Dltchbanks, Wasteland, General Farmstead, Utility Facilities (Including Substations, Tankfarms, 
Pumping Stations, and Parking and Storage Areas), Conservation Reserve Program Land, and Hayed or 
Grazed Areas on these Sites. Also for Pastures, Rangelands, Fallow Systems (Between crop Sorghum, Grass 
. (Hay or Silage), Sugarcane, and Wheat and Similar Noncropland Areas. 
ACTIVE INGREDIENTS: 
Dimethylamine Salt of 2,4-Dichlorophenoxyacetic Acid" ................................................... 3S.7% 
Dimethylamine Salt of Dicamba (3,6-Dichloro-Q-anisic Acid)" ......................... '.: . . . . . . . . . . . . . . . . . .. 12.4% 
OTHER INGREDIENTS: .............................................................................. ~ 
TOTAL: ......................... 100.0% 
Isomer Specific Method, Equivalent to: 
"2,4-Dichlorophenoxyacetic Acid .......... :............................................. 29.6%, 2.87lbs.lgaL 
··3,6-Dichloro-Q-anisic Acid ................................... -.. ... .. .. ... . . .. .. ... .. . . . . .. 10.3%,1.00 Ibs.lgal. 
KEEP OUT OF REACH OF CHILDREN 
'DANGER - PELIGRO 
Si usted no entiende la etiqueta, busque a alguien para que se la explique a usted en detalle. 
(If you do not understand the label. find someone to explain it to you in detaiL) 
SEE INSIDE BOOKLET FOR FIRST AID AND ADDITIONAL PRECAUTIONARY STATEMENTS 
For Chemical Spill, Leak, Fire, or Exposure, Call CHEMTREC (800) 424-9300 
For Medical Emergencies Only, Call (877) 32.5-1840 
NOTE: Spanish language is optional 
EPA REG. NO. 228-414 
EPA EST. NO. 228-IL-l 
NET CONTENTS GALS. 
000228.-00414.2007110S.Pending RED 
MANUFACTURED BY 
NUFARM AMERICAS INC. 
150 HARVESTER DRIVE 
BURR RIDGE, IL 60527 
. ACCEPTED 
with CCtdMENrs 
in EPA IAIf« DIced 
JUl 9 2008 
Malarm 
Under aile hdcnI IIlItcticide 
Fungicide, .. ROdamcide Aci 
as . amended, Ilr !he pesticide 
reg&stclld IIDder EPA Reg. No.

PRECAUTIONARY STATEMENTS 
HAZARDS TO HUMANS AND DOMESTIC ANIMALS 
DANGER - PELIGRO 
Corrosive. Causes irreversible eye damage. Harmful if swallowed. Do not get in eyes or on clothing. Avoid breathing spray mist 
PERSONAL PROTECTIVE EQUIPMENT (PPE) 
Some materials that are chemical-resistant to this product are barrier laminate. butyl rubber. nitrile rubber or viton. If you want more 
options. follow the instructions for category A on an EPA chemical-resistance category s,election chart. . 
All mixers, loaders, applicators, flaggers, and other handlers must wear: 
- long-sleeved shirt and long pants. . 
- shoes and socks. plus 
- chemical-resistant gloves, when applying postharvest dips or sprays to citrus, applying with any handheld nozzle or equipment. 
mixing or loading. cleaning up spills or equipment. or otherwise exposed to the concentrate. 
- chemical-resistant apron when applying postharvest dips or sprays to citrus. mixing or loading. cleaning up spills or equipment.. or 
otherwise exposed to the concentrate. 
- protective eyewear 
See engineering controls for additional requirements. 
Follow manufacturer's instructions for cleaning/maintaining PPE. If no such instructions for wash abies exist, use detergent and hot 
water. Keep and wash PPEseparately from other laundry. 
Engineering Control Statements: If this container is over one gallon and less than five gallons, then persons engaged in open 
pouring of this product must also wear coveralls or a chemical-resistant apron. If this container is five gallons or more in capacity. do 
not open pour from this container. A mechanical system (such as a probe and pump or spigot) must be used for transferring the 
contents of this container. If the contents of a non-refillable pesticide container are emptied. the probe must be rinsed before removal. 
If the mechanical system is used in a manner that meets the requirement~ listed in the Worker Protection Standard (WPS) for 
agricultural pesticides [40 CFR 170.240(d) (4-6)]. the handler PPE requirements may be reduced or modified as specified in the WPS. 
When handlers use closed systems. enclosed cabs. or aircraft in a manner that meets the requirements listed in the Worker Protection 
Standard (WPS) for agricultural pesticides t40 CFR 170.240(d) (4-6)]. the handler PPE requirements may be reduced or modified as 
specified in the WPS. 
USER SAFETY RECOMMENDATIONS 
Users Should: 
• Wash hands before eating. drinking. chewing gum. using tobacco or using the toilet 
• remove clothing/PPE immediately if pesticide gets inside. Then wash thoroughly and put on clean clothing. If pesticide gets on 
skin. wash immediately with soap and water. 
• Remove PPE immediately after handling this product. Wash the outside of gloves before removing. As soon as possible. wash 
thoroughly and change into clean clothing. 
FIRST AID 
IF IN EYES • Hold eye open and rinse slowly and gently with water for 15 to 20 minutes. 
• Remove contact lenses, if present. after the first 5 minutes. then continue rinsing eye. 
• Call a poison control center or doctor for treatment advice. 
IF SWALLOWED • Call a poison control center or doctor immediately for treatment advice. 
• Have person sip a glass of water if able to swallow. 
• Do not induce vomiting unless told to do so by the poison Control center or doctor. 
• Do not give anything by mouth to an unconscious person. 
HOT LINE NUMBER 
Have the product container or label'with you when camrig a poison control center or doctor, or going for treatment. 
You may afso contact 1-877-325-1840 for emergency medical treatment information. 
NOTE TO 'PHYSICIAN 
Probable mucosal damage may contraindicate the use of gastriC lavage. 
ENVIRONMENTAL HAZARDS 
This pesticide may be toxic to fish and aquatic invertebrates. Do not apply directly to water. to areas where surface water is present. 
or to intertidal areas below the mean high water mark except as noted on appropriate labels. Drift and runoff may be hazardous to 
aquatic organisms in water adjacent to treated areas. Do not contaminate water when disposing of equipment wash waters or rinsate. 
This chemical has properties and characteristics associated with chemicals detected in groundwater. The use of this chemical in 
areas where soils are permeable. particularly where the water table is shallow. may result in groundwater contamination. Application 
around a cistern or well may result in contamination of drinking water or groundwater. 
2

" 
DIRECTIONS FOR USE 
It is a violation of Federal law to use this product in a manner inconsistent with its labeling. READ ENTIRE LABEL BEFORE USING 
THIS PRODUCT. USE STRICTLY IN ACCORDANCE WITH LABEL PRECAUTIONARY STATEMENTS AND DIRECTIONS. Do not 
apply this product in a way that will contact workers or other persons, either directly or through drift. Only protected. handlers may be 
in 'the area during application. For any requirements specific to your State or Tribe, consult the agency responsible for pesticide 
regulation. 
AGRICULTURAL USE REQUIREMENTS 
Use this product only in accordance with its labeling and. with the Worker Protection Standard,.40 CFR Part 170. This Standard 
contains requirements for the protection of agricultural workers on farms, forests, nurseries, and greenhouses, and handlers of 
agricultural pesticides. It contains requirements for training, decontamination, notification, and emergency assistance. It also 
contains specific instructions and exceptions pertaining to the statements on this label about Personal Protective Equipment (PPE) 
and restricted-entry interval. The" requirements in this box only apply to uses of this product that are covered by the Worker 
Protection Standard. 
Do not enter or allow worker entry into treated areas during the restricted entry interval (REI) of 48 hours. 
PPE required for early entry to treated areas that is permitted under the Worker Protection Standard and that involves contact with 
anything that has been treated, such as plants, soil, or water, is: coveralls, chemical~resistant gloves made of any water-proof 
material, shoes plus socks, protective eyewear. 
NON-AGRICULTURAL USE REQUIREMENTS 
The requirements in this box apply to uses of this product that are NOT within the scope of the Worker Protection Standard for 
agricultural pesticides (40 CFR Part '170). The WPS applies when this product is used to produce agricultural plants on farms, 
forests, nurseries, or greenhouses. 
For turf and industrial use: Do not enter or allow people (or pets) to enter the treated area until sprays have dried. 
GENERAL INFORMATION 
This product is a water dilutable amine especially prepared for use on weeds and crops where a susceptible crop in the near vicinity 
may be injured by a more volatile product. It is recommended for control of numerous broadleaf weeds and certain 2,4-0 susceptible 
woody plants without injury to most established grasses. 
For best results, apply this product as a water or oil spray during warm weather when young succulent weeds or brush are actively 
growing. Application under drought conditions often will give poor results. The lower recommended rates will be satisfactory on 
susceptible annual weeds. For perennial weeds and conditions such as the very dry areas of the Western states, where control is 
difficult, the higher recommended rates should be used. 
Generally the lower 'dosages given will be satisfactory for young,succulent growth of sensitive weed species. For less sensitive 
. species and under conditions where control is more difficult, the higher dosages will be needed. Apply this product during warm 
weather when weeds are young and growing actively. Unless otherwise recommended, suggested application rates may be from 1 
to 10 gallons of total spray by air or 5 to 40 gallons by ground application equipment. If band treatment is used, base the dosage rate 
on the actual area to be sprayed. Although water quantities may vary due to different types of application equipment, sufficient water 
'must be used to provide for complete and uniform coverage. Higher water gallonage may be used if desired to improve spray 
coverage. In all cases, use the same recommended amount of 2,4-0 per acre. When product is used for weed control in crops, the 
growth stage of the crop must be considered. For crop uses, do not mix with oil, surfactants, or other adjuvants unless specifically. 
recommended on label. To do so may reduce herbicide's selectivity and could resuH in crop damage. If you are not prepared to accept 
some degree of crop injury, do not use this product. Crop varieties vary in response to 2,4-0 and some are easily injured. Apply this 
product to varieties known to be tolerant to 2,4-0. If you are uncertain concerning tolerant varieties or local use situations that may 
affect crop tolerance to 2,4-0, consult your seed company, State Agricultural Extension Service or qualified crop consultant's advice. 
Aerial applications should be used only when there is no danger of drift to susceptible crops. Many states have regulations concerning 
aerial application of 2,4-0 formulations. Consult local regulatory authorities before making applications. Do not apply when 
temperature exceeds 90°F. Read and follow all directions and precautions on this label and on the labels of any products for. which 
a tank mixture is being considered. 
SPRAY DRIFT MANAGEMENT 
A variety of factors including weather conditions (e.g., wind direction, wind speed, temperature, relative humidity) and method of 
applicati.on (e.g., ground, aerial, airblast, chemigation) can influence pesticide drift. The applicator must evaluate all factors and make 
appropriate adjustments when applying this product. . 
DROPLET SIZE 
When applying sprays that contain 2,4-0 as the sole active ingredient, or when applying sprays that contain 2,4-0 mixed with active 
ingredients that require a Coarse or coarser spray, apply only as a Coarse or coarser spray (ASAE standard 572) or a volume mean 
diameter of 385 microns or greater for spinning atomizer nozzles. 
When applying sprays that contain 2,4-0 mixed with other active ingredients that require a Medium or more fine spray, apply only as 
a Medium or coarser spray UI,SAE standard 572) or a volume mean diameter of 300 microns or greater for spinning atomizer nozzles. 
3

WIND SPEED 
Do not apply at wind speeds greater than 15 mph. Only apply this product if the wind direction favors on-target deposition and there 
are not sensitive areas (including, but not limited to, residential areas, bodies 01 water. known habitat for nontarget species. nontarget 
crops) within 250 feet downwind. If applying a Medium spray, leave one swath unsprayed at the downwind edge of the treated field. 
TEMPERATURE INVERSIONS 
If applying at wind speeds less than 3 mph, the applicator.must determine if: a) conditions of temperature inversion exist, or b) stable 
atmospheric conditioris exist at or below nozzle height. Do not make applications into areas of temperature inversions or stable 
atmospheric conditions. 
Susceptible Plants 
Do not apply under circumstances where spray drift may occur to lood, forage, or other plantings that might be damaged or crops 
thereof rendered unfit for sale, use or consumption. Susceptible crops include, but are not limited to, conon, okra, flowers, grapes (in 
growing stage), fruit trees (foliage). soybeans (vegetative stage), ornamentals, sunflowers, tomatoes, beans,and other vegetables, 
or tobacco. Small amounts of spray drift that might not be visible may injure susceptible broad leaf plants. 
Other State and Local Requirements 
Applicators must follow all state and local pesticide drift requirements regarding application of 2,4-0 herbicides. Where states have 
more stringent regula~ons, they must be observed. . 
Equipment 
All aerial and ground application equipment must be properly maintained and calibrated using appropriate carriers or surrogates. 
Additional requirements for aerial appliCations: 
The boom length must not exceed 75% of the wingspan or 90% of the rotor blade diameter. 
Release spray at the lowest height consistent with efficacy and flight safety. Do not release spray at a height greater than 10 feet 
above the crop canopy unless a greater height is required for aircraft safety. This requirement does not apply to forestry orrights-of­
way applicati,ons. 
When applications are made with a crosswind, the swath will be displaced downwind. The applicator must compensate for this by 
adjusting the path of the aircraft upwind. 
Additional requirements for ground boom application: . 
Do not apply with a nozzle height greater than 4 feet above the crop canopy. 
4

TABLE 1; APPLICATION RATE AND TIMING-ANNUAL WEEDS 
Weeds Controlled VETERAN 3010 RATE PER ACRE (ACCORDING TO GROWTH STAGE) 
(including AXIS - and 0-5 PINT 1 PINT 1.5 PINT 2 PINTS 3 PINTS 4 TO 5.5 PINTS triazine-resistance 
Beebalm, Spotted - - - Pre-bloom postbloom -
Broomweed 1 to 3" 3" branching - Branching - after branching 
Buckwheat, Wild - 1 to 6" - - - -
Buffalobur - - - 1 to 6" . - flowering 
Burdock - pre-liower - - - -
Buttercup - pre-flower - early bloom late bloom -
Chickweed Common - seedlina 1 to 3" -. - -
Cockle. Cow - <3" - - - -
Cocklebur Common - 1 to 6" 6 to 12" 12 teL 18" - -,... Plains - 1 to 6" - - - .-
Croton Woollv 1 to 4" 4 to 12" 12t030" - - -
Devils-Claw - - - <8" - -
Doafennel - - - 10to 15" - -
Eveninc Primrose - <2" - ? In fi" - -
Flax - < 2" - - - -
Fleabane Annual - 1 to 4" 4to 8" 8" - -
Flixweerf - <3" - - - -
Henbit - - ore-flower - flower -
Soo. - < 3" runners - > 3" runners - .acfutelv crowino 
Kochia - 1 to 6" fi In 10" 10 In 20" - activel;' nrnwino 
LambsQuarter Common - 1 to 6" 6 to 10" 10 to 20" - activelv orowina 
Mallow. CO_ffi!11QI1 - <3" - - - -
Morninoalorv - ore-flower - - - -
Ivvleaf Tall - pre-flower - oost·f1ower - -
Mustards. Annual rosette ""rfv holt - -
Tansv - <3" 
Pennvcress Field - - rosette - -
Pepperweeo VirQinia - - 1 to 3" 3 to 6" after -
Piaweed Prostrate - <3" - - branchinQ -
Redroot - <3" 3 to 10" - - -
Smooth - <3" - - - -
Tumble - <3" . - mature - -
Poorioe - prior to flower - - - activelV.Qrowina 
Purslane Common - < 3" 3 to 8" - -
Raaweed Common 6 to 10" >10" 
Western. Lanceleaf 3to 6" - activelv arowina - -
SAnn" , 1 103" - - -
Sheoherdspurse - rosette - - -
-
Pennsvlvania - <4" , oriorJo - -
SnAAzAweed, Bitter - 1 to 4" flower flower - -
Sow1histle - rosette - boltinQ 4to 12" -
<:. mflm", .. , - 1 103" 3 to 6" 6 to 24" - -
Thistle. Russian - - - rn<::AttA - -
Velvetleaf - <6
t1 
6t020" >20" - -
, For use in non-food/feed crop only. Adding crop oil concentrate has shown to improve performance on actively growing 
annual sedge. 
AERIAL APPLICATION METHODS MID EQUIPMENT 
Water Volume: Use 1 to 10 gallons of total spray per acre. Use the higher spray volume when treating dense or tall vegetation. 
Application Equipment: Select nozzles designed to produce minimal amounts of fine spray particles. Make applications at the 
lowest safe height to reduce the exPosure of spray droplets to evaporation and wind. The applicator must follow the most restrictive 
use cautions 10 avoid drift hazards, including those found in this labeling as well as applicable State and local regulations and 
ordinances. 
Do'not use aerial equipment'if spray particles can be carried by the wind into areas where sensitive crops or plants are growing or 
when temperature inversions exist. 
5

TABLE 2. APPLICATION RATE AND TIMING-ANNUAL WEEDS 
VETERAN 3010 RATE PER ACRE (ACCORDING TO GROWTH STAGE) 
WEEDS 
CONTROLLED 0.5 PINT 1 PINT 1.5 PINTS 2 PINTS 3 PINTS 4 TOS PINTS 
Bindweed Reid - - - - - activelY arowina 
Bittercress - 2 to 3" - - - -
Buckeye species' - - - - full leaf -
Bullnettle' - - - flower - -
Chicory - - ore-flower - ear1y boltina -
Clover, Bur - - - - - -
Dandelion Common - rosette - boltina - -
Dewberry, Southern' - - prior to - - spring or lall 
Dock Curly - - boltina - after boltina -
Elderberry' - - - - - . actively growing 
Goldenrod Missouri - - - 3 to 15" flower -
Goldenweed. Common - - - - - actively growing 
Groundsel, Texas - rosette post-bolting - - -
Honeysuckle. Hairy - - - - spring or fall -
HorsenettJe, Carolina' - - - - - flower or berry 
Ivy, Poison - - - after bloom - -
Knapweed, Black' - - - - - actively QrowinQ 
Russian' - - - - - actively growing 
Spotted - - - - actively growing 
Marsheld - - - < 12" 12"'prebloom 
Mesquite - - 45 to 90 days 
atter bud-break 
Milkweed Antelopehorn' - - - -.me-flower - flower 
Niahtshade. Silverleaf' - - - full flower - -
Black' - - - fulillower - actively growing 
Persimmon, Eastern' - - - - - actively growing 
Prickly lettuce - - - rosette - actively growing 
Rabbitbrush' - - - - - -
Ragowrt, Tansy - - - . rosette - actively growing 
Redvine' - - - - - actively growing 
Saaebrush FrinQed' - - - - actively QrowinQ 
Smartweed, - - - - - -
Sorrel, Red - - rosette bolting flower actively growing 
Sowthistle' - - - - - actively growing 
Spurge, Leafy' - - - - - full leaf 
Tallow Tree, Chinese' - rosette -
Thistle, Bull - - - boltinQ - actively_growing 
Canada' - - - - -
Musk - - rosette rosetteiboltina - -
Plumeless - - 4to S" bolting - -
Vetch, Hairy - 1 to 4" - 8'! full flower - -
Yankeeweed - - - 10 to 18" - rosette 
Yellow Starthistle' - - -
, May require repeat applications. 
, Recommended rate will provide top growth suppression only. 
, For improved root kill or weedy species such as mesquite and eastern perSimmon, spray 4 pints of Veteran 3010 per acre 
each year for 3 consecutive years. For increased control of weeds such as blackberry and dewberry, this product may be 
tank mixed with a metsulfuron-rnethyl 60% herbicide (0.1 to 0.2 ounces per acre), if labeled lor the use site . 
• Under dense populations, a second application may be needed the following growing season. 
GROUND APPLICATION (BANDING) 
When applying Veteran 3010 by banding, determine the amount of herbicide and water volume needed using the following formula: 
Bandwidth in inches 
Row Width In Inches 
Bandwidth in inches 
Row width in inches 
x 
x 
Broadcast rate 
per acre 
Broadcast volume 
per acre 
6 
Banding herbicide 
rate per acre 
Banding water 
volume per acre

GROUND APPUCATJON (BROADCAST) 
Water Volume: Use 5 to 40 gallons of spray solution per broadcast acre for optimal perform.ance. Use the higher spray volume when 
treating dense or tall vegetation. Physical incompatibility, reduced weed control, or crop injury may result from mixing this product 
with other pesticides (fungicides herbicides, insecticides, or miticides), additives, or fertilizers .. NUFARM does not recommend using 
tank mixes other than those listed on NUFARM labeling. Local agricultural authorities may be a source of information when using 
other than NUFARM recommended tank mixes. 
COMPATIBILITY TEST FOR MIX COMPONENTS 
Before mixing components always perform a compatibility jar test . 
For 20 gallons per acre spray volume, use 3.3 cups (SOO ml) of water. For other spray volumes, adjust accordingly. Only use water 
from the intended source at the source temperature. 
Add components in the sequence indicated in the mixing order using 2 teaspoons for each pound or 1 teaspoon for each pint of 
recommended label rate per acre.' . 
Always cap the jar and invert 10 cycles between component additions. 
When ttie components have all been added to the jar, let the solution stand for 15 minutes, Evaluate the solution for uniformity and 
stability. The spray solution should not have free oil on the surface, nor fine particles that precipitate to the bottom, nor thick 
(c1abbered) texture. If the spray solution is not compatible, repeat the compatibility test with the addition of a suitable compatibility 
agent If the solution is then compatible. us~ the compatibility agent as directed on its label. If the solution is still incompatible, do not 
mix the ingredients' in the same tank. 
MIXING ORDER 
If an inductor is used, rinse it thoroughly after each component has been added. Maintain constant agitation during application. 
1) Water'. Begin by agitating a thoroughly clean sprayer tank half full of clean water. 
2) Agitation. Maintain constant agitation throughout mixing and application. 
3) Products in PVA bags. Place any product contained in water-soluble PVA bags into the mixing tank. Wait until all water-soluble 
PVA bags have fully dissolved and the product is evenly mixed in the spray tank before continuing. 
4) Water-dispersible products (such as dry f1owables, wettable powders, suspension concentrates, or suspo-emulsions 
5) Water-soluble products. (such as Veteran 3010) 
6) Emulsifiable concentrates (such as oil concentrate when applicable) 
7) Water-soluble additives (such as liquid fertilizers (28-0-0, 32-0-0) when applicable) 
8) Remaining quantity of water. 
If sprayable fluid fertilizer is used as the carrier, Veteran 3010 must be diluted with a minimum of 5' parts water to 1 part Veteran 
3010. Then add 0.25 to .05% volumelvolume of a nonionic surfactant to the dilution before adding it to the sprayable fluid fertilizer 
to reduce the concern tor compatibility problems with this mix. Always perform the compatibility test before mixing into the spray 
tank. Also, when using a sprayable fluid fertilizer as the carrier, any product contained in PVA bags must first be completely 
dissolved in water before the contents can be added to the fertilizer mix. 
CROP ROTATIONAL RESTRICTIONS 
The interval between application and planting rotational crop is given below. Always exclude counting days when the ground is frozen. 
Planting at intervals less than specified below may result in crop injury. Moisture is essential for the degradation of this herbicide in 
soil. If dry weather prevails, use cultivation to allow herbicid~ contact with moist soil. 
Planting/replanting restrictions for Veteran 3010 Herbicide applications of 6 pints per acre or less: No rotational cropping 
restrictions apply at 120 days or more following application. Additionally, for annual crop uses in this label including sorghum follow 
the preplant use directions in the Food/Feed Crop-SpeCific Information Section. For barley, oat, wheat, and other grass seedings, the 
interval between application and planting is 10 days per pint per acre. 
Application Equipment: Select nozzles designed to produce minimal amounts of fine spray particles. Spray with nozzles as close 
to the weeds as is practical for good weed coverage. . 
SPOT OR SMALL AREA APPLICATION 
Veteran 3010 Herbicide may be applied to individual clumps or small areas of undesirable vegetation using handgun or similar types 
of application equipment. Apply diluted sprays to allow complete wetting (up to runoff) of foliage and stems. For knapsack or other 
small capacity sprayers, prepare a solution of this product in water according to Table 3 (assuming that the spot treatment rate 
equates to 60 gallons per acre on the broadcast basis.) Adding a surfactant (0.5% by volume) can help improve control. For example, 
5 gallons (40 p,ints or 640 fluid ounces) of herbicide solution would require 0.2 pints (3.2 fluid ounces) of surfactant. Do not make spot 
treatments in addition to broadcast or band treatments. . 
Application Equipment: Select nozzles designed to produce minimal amounts of fine spray particles. Spray with nozzles as close 
to the weeds as is practical for good weed coverage. 
7

TABLE 3. KNAPSACK SPRAYER DILUTION INSTRUCTIONS 
SPRAYER CAPACITY AMOUNT OF VETERAN 3010 
TO ADD TO THE (GALLONS OF WATER) SPRAY TANK 
1 gallon 1 fluid ounce" 
3 gallons 3 fluid ounces 
5 gallons 5 fluid ounces 
"1 lIuid ounce + 2 tablespoons 
ADDITIVES 
To improve burndown of emerged weeds, surfactants and/or low use rate of liquid fertilizers (28-0-0, 32-0-0), or crop oil concentrate 
may be used with this product or tank mixes applied after the weeds have emerged. Crop oil concentrate is for non-food/feed crop 
uses only. 
Do not apply tank mixes that include ammonium sulfate or crop oil concentrate to any foodlfeed crop use listed on this label. For 
foodlfeed crop uS.es, do not use liquid fertilizers that contain ammonium sulfate (AMS) as a source of nitrogen as tolerances. in 
commodities derived from the crop may contain residues that exceed established tolerances. Consult your local NUFARM 
representative for recommendations for your area. For additional information,. see Compatibility Test for Mix Components. 
Oil Concentrate 
A crop oil concentrate must contain either a petroleum or vegetable oil bilse and must meet al\ of the following criteria: 
benonphytotoxic, contain only EPA-exempt ingredients, 
• provide good mixing quality in the jar test, and 
- be successful in local experience. 
The exact composition of suitable products will vary; however, vegetable and petroleum oil concentrates should contain emulSifiers 
to provide good mixing quality. Highly refined vegetable oils have proven more satisfactory than unrefined vegetable oils. For 
additional information, see compatibility test for mix components. 
Adjuvants containing crop oil concentrates may be used for preplant, pre-emergence and between cropping applications. Do not use 
crop oil concentrate for post-emergence applications in foodlfeed crops (i. e., sorghum, grass (hay or silage). pastures, rangeland, 
sugarcane and wheat). .' 
Nitrogen Source 
• Sprayable liquid fertilizers: Use one quart of sprayable liquid fertilizers (28.0-0, 32-0-0) per acre. Do not use brass or aluminum 
nozzles when spraying tertilizer$. 
Nonionic Surfactant 
The standard label recommendation is 2 to 4 pints of a non ionic spray surfactant per 100 gallons of water. For certain weeds, use a 
higher spray surfactant rate. 
TABLE 4. ADDITIVE RATE PER ACRE 
ADDITIVE RATE PER ACRE 
Nonionic Surfactant 2 to 4 pints per 100 gallons 
Sprayable liquid fertilizers (28-0-0, 32-0-0) 2 to 4 quarts 
Crop Oil Concentrate 1 quart" 
"See manufacturer's label for specific rate recommendations; 
INDUSTRIAL WEED AND BRUSH CONTROL, 
CONSERVATJON RESERVE PROGRAMS AND GENERAL FARMSTEAD 
Veteran 3010 Herbicide is recommended for use for industrial, conservation reserve programs, general farmstead (non-cropland 
only), weed and brush control, or use in state recognized noxious weed areas (noncropland areas). 
Refer to Tables 1 and 2 for rate selection based on targeted weed or brush species. Some weed species will require tank mixes for 
adequate contro!. 
Rates above 4 pints of Veteran 3010 per acre are for spot treatments only. 
USE PRECAUTIONS FOR INDUSTRIAL WEED AND BRUSH CONTROL, 
CONSERVATION RESERVE PROGRAMS AND GENERAL FARMSTEAD 
The preharvest interval (PHI) is 7 days (cut forage for hay). 
post-emergence (annual and perennial weeds): 
Limited to 2 applications per year. 
8

Maximum of 5.5 pints per acre per application. 
Minimum of 30 days between applications. 
If grass is to be cut for hay, Agricultural Use Requirements for the Worker Protection Standard are applicable. 
Post-emergence (woody plants): 
limited to 1 application per year. 
Maximum of 11 pints per acre per year. . 
Applications to non-cropland areas are not applicable to treatment 01 commercial timber or other plants being grown for sale·or other 
commercial use, or for commercial seed production, or for research purposes. 
For program lands, such as Conservation Reserve Program, consult program rules to determine whether grass or hay may be used. 
The more restrictive requirements of the program rules or this label must be followed. 
GENERAL TANK MIXING INFORMATION 
Tank Mix Partners/Components 
The tollowing products may be. tank mixed with Veteran 3010 according to the specific tank mixing instructions in this label and 
respective tank mix partner's product labels. No label dosage r<;ite should be exceeded. 
• QuickSilver® 
'Patriot® 
• triasulfuron 
: asulam 
• atrazine 
• Diablo® 
'bentazon 
.• bromoxynil + MCPA 
• bromoxynil 
• thifensulfuron + tribenuron + metsulfuron 
• paraquat 
• diuron 
• pronamide 
• bentazon + atrazine 
• glyphosate + 2,4-0 
• metribuzin 
·.MCPA 
• quinclorac 
• prosulfuron 
·dicamba 
• clopyralid + 2,4-0 
.• fenoxaprop-p-ethyl + MCPA 
• diflufenzopyr 
'ametryn 
• thifensulfuron + tribenuron-methyl 
• glyphosate + dicamba 
• chlorsulfuron + metsulfuron-methyl 
• chlorsulfuron 
• halosulfuron-methyl 
• dicamba + triasulfuron 
• Razor® (glyphosate) 
• terbacil 
• clopyralid 
• fenoxaprop-p-ethyl + 2,4-0 + MCPA 
• picloram 
• sulfosate 
• 2,4-0 
See Food/Feed Crop-Specific tnformation for more details. Read and follow the applicable Restrictions and Limitations and Directions 
For Use on all product involved in tank mixing. The most restrictive labeling applies to tank mixes.' This product cannot be mixed with 
any product containing a label prohibition against such mixing. . 
Planting/replanting restrictions for applications of more than' 6 pints and up to 8 pints of Veteran 3010 per acre: Corn, 
sorghum, cotton (east of the Rocky Mountains) and all other crops grown in areas with 30 inches or more of annual rainfall may be 
planted 120 days or more alter application. Barley, oat, wheat, and other grass seedings, may be planted if the interval from 
application to planting is 10 days per pint per acre east of the Mississippi River and 15 days per pint per acre west of the Mississippi 
River. For all other crops in areas with less than 30 inches of annual rainfall, the interval between application and planting is 180 days 
or more. 
• Rainfast period: Rainfall or Irrigation occurring within 4 hours after postemergence applications may reduce the effectiveness of 
this product. 
• Stress: Do not apply to crops under stress such as stress due to lack of moisture, hail damage, flooding, herbicide injury, 
mechanical injury, or widely fluctuating temperatures, as unsatisfactory control may result 
• Do not apply to crops that show injury (leaf phytotoxicity or plant stunting) produced by any other prior herbicide applications, 
because this injury may be enhanced or prolonged. 
: This product cannot be used to formulate or reformulate any other pesticide product. 
9

TABLE 5. CROP-SPECIFIC RESTRICTIONS AND LIMITATIONS 
MAXIMUM RATE MAXIMUM RATE LIVESTOCK AIRCRAFT CROP PER ACRE PER ACRE GRAZING OR APPLICATION PER APPLICATION PER SEASON FEEDING 
Between crop applications 6 pints 8 pints Yes Yes 
Pasture, Hay, Silage 4 pints Spints Yes Yes 
Sugarcane 5 pints '16 pints Yes Yes 
Sorgtium 1 pint 1 pint Yes Yes 
Wheat 2 pints 3.33 pints Yes Yes 
Refer to Food/Feed Crop-Specific Information for grazing and feeding restrictions. 
FOODIFEED CROP-SPECIFIC INFORMATION 
PASTURES, RANGELAND AND ,GRASS (HAY, SILAGE) 
Veteran 3010 Herbicide is recommended for use for pasture (including pasture grown for hay), rangeland and grass grown for hay or 
silage. Refer to Tables 1 and 2 for rate selection based on targeted weed or brush species. Some weed species will require tank 
mixes for adequate control. Rates above 4 pints of this product per acre are for spot treatments only. Retreatments may be made as 
needed; however, do nol exceed a total of 8 pints of this product per treated acre during a growing season. Uses described in this 
pertain to small grains (such as barley, corn, forage sorghum, oats, rye, sudangrass, or wheat) grown for pasture, hay, and silage 
only. Newly seeded areas, including small grains grown for pasture or hay, may be injured if rates of this product greater than 2 pints 
per acre are applied. ' 
In newly established hybrid Bermuda, Pangolagrass, and stargrasses (Cynodon spp.), use 2 to 4 pints of this product per acre to 
control or suppress weeds after planting vegetative propogules (stolens) of hybrid bermudagrasses. In addition to the weeds listed in 
Tables 1 and 2, the rate of this product will control or suppress annual sedges, broadleaf signalgrass, crabgrass, and goosegrass. 
Best results will be obtained if this product is applied at the germinating stage of weeds. Under favorable conditions, this is usually 7 
to 10 days after planting these grasses. Reduced control can be expected if weeds are allowed to reach 1 inch in height before 
application or if germination of weeds occurs 10 days after application. 
Do not use on bentgrass, susceptible grass pastures (such as carpetgrass, buffalograss, or St. Augustinegrass), lespedeza, wild 
winter peas, vetch, clover, and alfalfa pastures as injury will occur. When perennial weeds are reaching maturity, mowing and allowing 
some regrowth will enhance control. Difficult to control weeds and brush may require repeat applications. 
For pasture renovations, wait 3 weeks per quart (2 pints) of this product used per acre before interseeding or injury may occur. 
If grasses are grown for seed or for seed-dovitn purppses do not apply after grass reaches the jOint stage. 
When using on (1) pastures and rangeland grasses there is (a) 7 day pre-grazing interval for dairy cattle; (b) 30 day preharvest 
interval for grass cut for hay; and (c) 3 day pre-slaughter interval for meat animals. (2) Corn and small grains: Do not allow livestock 
to forage or graze treated fields within 14 days after treatment. Do not feed treated straw to livestock. (3) Sorghum: Do not allow 
livestock to graze treated areas within 14 days after treatment, and (4) Grass Seed Crops: Do not graze dairy animals within 7 days 
after treatment. 
Grazing and Feeding Non-lactating Animals: There is no waiting period between treatment and grazing for non-lactating animals. 
Do not permit meat animals being finished for slaughter to graze treated fields within 30 days of slaughter. 
Grazing and Feeding Lactating Animals: Do not graze lactating dairy animals within 7 days of treatment. 
Dry Hay and Silage: Treated grasses may be harvested foidry hay or silage but 'do not harvest within 37 days.of treatment. 
USE PRECAUTIONS FOR PASTURES, RANGELAND AND GRASS (HAY, SILAGE) 
Do not cut forage for hay within 7 days of application. 
Postemergence:' 
For susceptible annual and biennial broadleaf weeds: Use 2.25 pints per'acre per application. 
For moderately susceptible biennial and perennial broadleaf weeds: Use 2.25 to 5.5 pints per acre per application. 
For difficult to control weeds and woody plants: Use 5.5 pints per acre per application. 
Spot treatment: 
Use 2.25 pints per acre. 
Maximum of two applications per year. 
Maximum of 11 pints/acre per year. 
Minimum 'of 30 days between applications. 
If grass is to be cut for hay, Agricultural Use Requirements for the Worker Protection Standard are applicable. 
PASTURE AND RANGELAND TANK MIXES 
Veteran 3010 may be applied in tank mixes with cine or more of the following herbicides: 
Patriot~ 
triasulfuron 
Diablo' 
Diablo' + triasulfuron 
10

SORGHUM 
Rates and timings 
Apply 1 pint of Veteran 3010per acre to sorghum in ihe 3 to 5 leal stage (4 to S" tall). For best pertormance, apply when weeds are 
small (less than 3" tall). Applications 01 Veteran 3010 to sorghum during periods of rapid growth may result in temporary leaning of 
plants or rolling of leaves. These effects are usually outgrown within 10 to 14 days. Sorghum growing under conditions of stress such 
as high moisture, low fertility, and abnormal temperature may be more sensitive to application this product. . 
USE PRECAUTIONS FOR SORGHUM 
Do not use this product if the potential for sorghum injury is not acceptable. 
If sorghum is grown for pasture, hay, or silage, refer to Pasture and Rangeland in the Crop Specific Section information lor livestock 
grazing and feeding restrictions. 
Do not apply this product to sorghum grown for seed production. Make no more than one post-emergence application per 'growing 
season. 
Do not use surfactants or oils with post-emergence applications of this product on sorghum crops. 
The preharvest interval (PHI) is 30 days. 
Do not permit meat or dairy animals to consume treated crop as fodder or forage for 30 days following application. 
Post-emergence: 
limited to 1 application per crop cycle. 
Maximum 012.25 pints per acre per application. 
SORGHUM TANK MIXES 
Veteran 3010 Herbicide may be applied in tank mixes with one or more 01 the following herbicides. 
bentazon 
bromoxynil 
bentazon + atrazine 
quinclorac 
prosulfuron 
halosulfuron-methyl 
SUGARCANE 
Applications of Veteran 3010 herbicide can be made any time alter the weeds have emerged and are actively growing but prior to the 
close-in stage of sugarcane. When possible, direct the spray beneath the sugarcane canopy in order to minimize the likelihood of 
crop injury. The use of directed sprays will also aid in maximizing spray coverage of weed foliage. Application rates and. timing are 
given below. Use the higher level of listed rate ranges when treating dense vegetative growth. 
Rate: 
For control of listed annual broadleaf weeds, apply 2 pints of Veteran 3010 per treated acre. 
For suppression of listed perennial weeds. apply l' to 5.5 pints of this product per treated acre. Retreatments may be made as 
needed. 
USE PRECAUTIONS FOR SUGARCANE 
Do not harvest cane prior to crop maturity. 
Do not apply more than 11 pints per acre per crop cycle. 
Pre-emergence: 
Limited to one application per crop 
.cycle. 
Maximum of 5.5 pints per acre per application. 
Post-emergence: 
limited to one application per crop cycle. 
Maximum of 5.5 pints per acre per application. 
11 
15 
!Y\

SUGARCANE TANK MIXES 
Veteran 3010 Herbicide may be applied in tank mixes with one or more of the following herbicides: 
• QuickSilver® • chlorsulfuron 
'Patriot® 
• triasulfuron 
• asulam 
• atrazine 
• Oiablo® 
- bentazon 
• bromoxynil + MCPA I 
• bromoxynil 
• thifensulfuron + tribenuron + metsulfuron 
-dicamba 
• clopyralid + 2,4-0 
• paraquat 
• fenoxaprop·p-ethyl + MCPA 
• diflufenzopyr 
·ametryn 
• thifensulfuron + tribenuron·methyl 
• glyphosate + dicamba 
• chlorsulfuron + metsulfuron-methyl 
'diuron 
• pronamide 
• bentazon + atrazine 
• glyphosate + 2,4-0 
• metribuzin 
• MCPA 
• quinclorac 
• prosulfuron 
• halosulfuron-methyl 
• dicamba +'triasulfuron 
• Razor® (glyphosate) 
• terbacil 
, • clopyralid 
• lenoxaprop-p-ethyl + 2,4-0 + MCPA 
• picloram 
• sulfosate 
• 2,4-0 
WHEAT (FALL AND SPRING· SEEDED') 
If small grains are grown for pasture or hay only, refer to Pastures, Rangeland and Grass (Hay, Silage). Do not graze or harvest for 
livestock feed prior to crop maturity. Do not use this product in wheat underseeded with legumes. 
EARLY SEASON APPLICATIONS: Apply 0.5 to 1 pint of Veteran 3010 per acre to wheat unless using one 01 the wheat specific 
programs below. Early season applications to spring-seeded wheat must be made after tiUering and before wheat reaches the 6-leaf 
stage. Early season applications to fall-seeded wheat must be made after tillering and prior.to the jointing stage. Care should be' 
taken in staging early developing wheat varieties such as TAM 107, Madison, or Wakefield to be certain that the application occurs 
prior to the jointing stage. 
SPECIFIC USE PROGRAMS FOR FALL-SEEDED WHEAT ONLY: Up to 1.33 pints of Veteran 3010 per acre may be applied on fall­
seeded wheat after the wheat begins to tiller for suppression of perennial weeds, such as field bindweed. Applications may be made 
in the fall following a frost but before a killing freeze. Periods of extended stress such as cold and wet weather may enhance the 
possibility of crop injury. For fall applications only, do not use,if the potential for crop injury is not acceptable. 
PREHARVEST APPLICATIONS: Veteran 3010 can be used to control weeds that may interfere with harvest of wheat. Apply up to 2 
pints of this product per acre as a broadcast or spot treatment to annual broadleaf weeds when wheat is in the hard dough stage and 
the green color is gone from the nodes Ooints) of the stem. Best results will be obtained if application can be made when weeds are 
actively growing but before weeds canopy. A waiting interval of 7 days is required before harvest. Do not use preharvest-treated wheat 
for seed unless a germination test is performed on the seed with an acceptable result of 95% germination or belter. For control of 
··additional broadleaf weeds or grasses, this product may be tank mixed with other herbicides such as metsulfuron-methyl or 
glyph as ate that are registered for preharvest use in wheat. ' 
Preharvest use of Veteran 3010 Herbicide is not registered for use in California. 
USE PRECAUTIONS FOR WHEAT 
The preharvest interval (PHI) is 14 days. 
Post-emergence: 
Limited to one post-erDergence application per crop cycle. Maximum of 3.5 pints per acre per application. 
Pre harvest: 
Limited to one preharvest application per crop cycle. 
Maximum of 1-1/3 pints per acre per application. 
Limited to 4.5 pints per acre per crop cycle. 
TABLE 6. WHEAT TANK MIXES 
Tank mix recommendations are only lor use in states where the tank mix product and application site are registe'red. Read and follow 
, the label of each tank mix product. 
12

TANK MIX PARTNER 
QuickSilve~ 
Patrio~ 
triasulfuron' 
bromoxynil + MCPA 
bromoxynil 
thifensulfuron + tribenuron + metsulfuron' 
clopyralid 
fenoxaprop-p-ethyl. + MCPA' 
thifensulfuron + tribenuron-methyl' 
chlorsulfuron + metsulfuron-methyl' 
chlorsulfuron' 
diu ron' 
2.4-0 amine' 
metribuzin' 
prosulfuron' 
fenoxaprop-p-ethyl + 2.4-0 + MCPA'-' 
Do not 'use low rates of sulfonylurea herbiCides. such as Patrio~. triasulfuron. thifensulfuron. hletsulfuron, chlorsulfuron and 
prosulfuron on more mature weeds or on dense vegetative growth. 
, Do not use Veteran 3010 herbicide as a tank mix treatment with fenoxaprop or fenoxaprop-p-ethyl on durum wheat. Do not tank 
mix with fenoxaprop if wild oat is the target weed. 
, Tank mixes with diuron and metribuzin are for use in fall-seeded wheat only. 
BETWEEN CROP APPLICATIONS, CONSERVATION RESERVE PROGRAMS, 
GENERAL FARMSTEAD AND FALLOW SYSTEMS 
These uses are considered foodlfeed crops when harvested, grazed or foraged. Consult the Adjuvant Section for restrictions and 
Non-Food/Feed Use Section for specific use directions. 
NON-FOODIFEED USE (LAND NOT HARVESTED, GRAZED OR FORAGED) 
- SPECIFIC INFORMATION BETWEEN CROP APPLICATIONS 
PREPLANT DIRECTIONS (POSTHARVEST. FALLOW, CROP STUBBLE, SET-ASIDE) FOR BROADLEAF WEED CONTROL: 
Veteran 3010 herbicide can be applied either postharvest in the fall. spring, or summer during the fallow period or to crop stubblefset­
aside acres. Apply as a broadcast for spot treatment to emerged and actively growing weeds after crop harvest (post harvest) and 
before a killing frost or in the fallow cropland or crop stubble the following spring or summer. ' 
See Crop Rotational Restrictions Section. General Restrictions and Limitations for the recommended interval between application and 
planting to prevent crop injury. 
Rates and TImings: Apply 0.5 to 5.5 pints of Veteran ~OI 0 per acre. Refer to Table 1 to determine use rales for specific targeted 
weed species.' , 
Retreatments may be made as needed; however. do not exceed a total of 8 pints of this product per treated acre during a growing 
season. For best performance. apply Veteran 3010 when annual weeds are less than 6" tall. when biennial weeds are in the rosette 
stage and to perennial weed regrowth in late summer or fall following a mowing or tillage treatment. The most effective control of 
upright perennial broadleaf weeds such as Canada thistle and Jerusalem artichoke occurs if this product is applied when ihe majority 
of weeds have at least 4" to 6" of regrowth or for weeds such as field bindweed and hedge bindweed that are in or beyond the full 
bloom stage. 
AVOid disturbing treated areas following application. Treatments may not kill weeds that develop from seed or underground plimt parts 
such as rhizomes or bulblets. after the effective period for Veteran 3010. For seedling control. a follow-up program or other cultural 
practices could be instituted. 
USE PRECAUTIONS FOR FALLOW 
Plant only labeled crops within 29 days following application. 
Limited to 2 applications per year. 
Maximum of 5.S pints per acre per application. 
Minimum of 30 days between applications. 
BETWEEN CROP TANK MIXES 
In tank mixes with one or more of the following herbicides. apply 0.5 to 2 pints of this product per acre for control of annual weeds. 
or 2 to 5.S pints of this product per acre for control of biennial and perennial weeds: 
QuickSilver" 
Patrio~ 
triasulfuron 
atrazine 
clopyralid + 2,4-0 
paraquat 
diflufenzopyr 
glyphosate +·dicamba 
chlorsulfuron + metsulfuron-methyl 
Razor' 
pronamide 
quinclorac 
melribuzin 
picloram 
sulfosate 
2,4-D 
13 
II 
~\

( 
APPLICATION INSTRUCTIONS 
fOR RIGHTS-Of-WAY (INCLUDING ROADWAYS. UTILITY. RAILROAD. HIGHWAY, PIPEUNE. AND RIGHTS-Of-WAY THAT 
RUN THROUGH PASTURES AND RANGELAND). UTILITY FACILITIES (INCLUDING SUBSTATIONS. lANKFARMS, PUMPING 
STATIONS, AND PARKING AND STORAGE AREAS) NON IRRIGATED DITCHBANKS, FENCEROWS, AND GENERAL 
FARMSTEAD. 
Veteran 3010 may be applied using water or oil and water emulsions in spot application to control undesirable vegetation using 
handgun or similar types of application equipment. In addition to weed species listed in Tables 1 and 2, these treatments may be used 
to control or suppress woody plant species listed in Table 7. 
To prepare oil and water emulSiOns, mix in the order and proportions indicated below. The solution should remain milky colored 
without an oily layer on top when under agitation. If an oily layer forms, increase the amount of emulsifier or change to a more effective 
emulsifier. 
To control brush, briars,. and weeds along fence rows surrounding pasture and ranch lands, and fallow fields, use a tank mix of 2.5% 
of Veleran 3010, 87.5% water, 10% diesel oil, and sufficienl emulsifier (to mix the diesel and emulsifier). The diesel oil in this tank mix 
will damage or kill desirable grasses and should not be used in pastures or where damage to desirable species cannot be tolerated. 
1) Water: Begin by agitating a thoroughly clean sprayer tank with the desired quantity of clean water. Maintain constant agitation 
during complete mixing procedure. . 
2) Emulsifier: Add 0.5% volume to volume. 
3) Veteran 3010: Add 2.5 gallons per 100 gallons of total intended solution. 
4) Diesel Oil: Add 10 gallons per 100 gallons of total intended solulion. Maintain constant agitation during ClPplication. Under good 
agitation, the spray solution should be milky white with no oil layer on top. If an oil layer forms, increase the amount of emulsifier 
or change to a more effective emulsifier. 
USE PRECAUTIONS FOR RIGHTS-Of-WAY (INCLUDING ROADWAYS,UTILlTY,RAILROAD,HIGHWAY;PIPELlNE,AND 
RIGHTS-OF-WAY THAT RUN THROUGH PASTURES AND RANGELAND),UTIUTY FACILITIES (INCLUDING 
SUBSTATlONS,TANKFARMS,PUMPING STATlONS,AND PARKING AND STORAGE AREAS) NON IRRIGATED 
DITCHBANKS,FENCEROWS,AND GENERAL FARMSTEAD 
Post-emergence (annual and perennial weeds): 
Limited to 2 applications per year. 
Maximum of 5.5 pints per acre per application. 
Minimum of 30 days between applications. 
Post-emergence (woody plants): 
Limited to 1 application per year. 
Maximum of 11 pints lacre per year. 
Applications to non-cropland areas are not applicable to treatment of commercial timber or other plants being grown for sale or other 
commercial use, or for commercial seed production, or for research purposes. 
FOR SPRAYING FOLIAR APPLICATIONS: 
1. Spray when leaves have reached full size but have not hardened due to drought or maturity. 
2. Spray individual plants to wet with handgun. 
3. For larger stems (up to 3 feet in diameter) and hard to control species, direct spray stream to base of stems to wet the stem at soil 
surface in addition to wetting the loliage. 
4 .. Do not apply under drip line of desirable trees or adjacent to desirable vegetation. 
FOR DORMANT BASAL APPLICATIONS: 
1. Increase diesel oil cOntent to 15% or 15 gallons of diesel oil per 100 gallons 01 total solution. 
2. Spray in late winter and early spring belore plants break dormancy .. 
3. Spray the bottom 24 inches of the target stem to wet on all sides. 
4. For larger stems (up to 3 feet in diameter) and hard to kill species direct the spray solution to the base of target stems to wet the 
soil at the stemfsoil junction in addition to wetting the stem. 
5. Do not apply under drip line of desirable trees or adjacent to desirable vegetation. 
FOR CUT SURFACE TREATMENTS: 
Apply Veteran 3010 in an undiluted state as a cut surface treatment to control unwanted trees and prevent sprouts 01 cut trees. 
Frill or Girdle Treatments: Make a continuous cut or a series of overlapping cuts using an axe to girdle tree trunk. Spray or paint 
the cut surface wilh this product. . 
Stump Treatments: Spray or paint freshly cut surface with Veteran 3010. The cambium layer (the area adjacent to the bark) 
shOUld be thoroughly wet. Treat stumps within 6 hours after cutting. 
HERBACEOUS BROADLEAF WEED CONTROL: Apply 1 to 3 quarts of this product in 20 to 100 gallons of water per treated acre 
(3/4 to 2.5 fluid ozs. per 1,000 sq. ft.). When using low volume application equipment, 3 to 20 gallons of water per acre is acceptable. 
1 to 2 quarts per acre (3/4 to 1.5 fluid ozs. per 1,000 sq. ft.) of this product is recommended for annuals, 2 to 3 quarts per acre for 
14

biennials, and 3 quarts per acre for established perennials. Do not apply more than 5-1/2 quarts of product per treated acre. 
BRUSH AND VINE CONTROL - High Volume Foliar Spot Applications: Mix 4 to 5-1/2 quarts of this product in enough water to make 
100 gallons of spray mix. When using· low-volume application equipment, 3 to 20 gallons of water per acre is acceptable. Spray 
volume applied will depend on the size and density of the brush to be treated, but do not apply more than 5-1/2 quarts of product per 
treated acre. Direct the spray to treat all foliage, stems, and root collars to wet. 
BRUSH AND VINE CONTROL - Broadcast applications with Ground Equipment: Apply 4 to 5-1/2 quarts of this produc\in 20 to 100 
gal/ons of water per treated acre. When using low-volume application equipment, 3 to 20 gallons of water per acre is acceptable. 
Spray volume applied will depend on the size and density of the brUSh to be treated, but do not apply more than 5-1/2 quarts of 
product per treated acre. Spray all foliage, stems, and root collars to wet. 
AERIAL APPLICATIONS: Aerial applications may be made to control either herbaceous or woody plants. Apply 1 to 3 quarts of this 
product for herbaceous weeds or 4 to 5-112 quarts for woody brush and vines in 5 to 40 gallons of water per acre. Coverage is 
important, so increase spray volume when treating dense stands of brush or weeds. Do not apply more than 5-1/2 quarts of product 
per treated acre. 
READ AND FOLLOW THE LABEL OF EACH TANK MIX PRODUCT USED FOR PRECAUTIONARY STATEMENTS, DIRECTIONS 
FOR USE, AND OTHER RESTRICTIONS. For broader spectrum ·control. This product may be tank mixed with one or more of the 
following herbicides for non-cropland use (e.g. railroad, highway, pipeline, etc.). 
Amitrole Diquat Maleic hydrazide Simazine 
Asulam Diuron Mefluidide Sulfometuron methyl 
Atratol Fenac Metsulfuron methyl Sulfosate 
Bromacil Fosamine ammonium MSMA Tebuthiuron 
Clor1lurecol Glyphosate Nor1lurazon Triclopyr 
Chlorsulfuron Glufosinate Paraquat 2,4-0 
Clopyralid Hexazinone Pendimethalin 2,4-DP 
Dalapon Imazapyr Picloram 
Dicamba Imazameth Prodiamine 
Due to variations in formulated products ,and water supplies, a compatibility test is recommended prior to actual tank mixing. 
All intended tank mix combinations should be used only in recommended areas on the same broadleaf weed species. found on both 
labels. For application methods and other use specifications, use the most restricted limitations from labeling 01 both products. 
Table 7. TREES AND VINES CONTROLLED 
The following list of trees and vines can be controlled on farmsteads and fencerows as foliar, basal, or cut surface treatments: 
Alder Elm Locust, Black Rose, Multiflora 
Ash Grape Maple Sagebrush, Fringe 
Aspen Greenbriar Mesquite Sassafras 
. Basswood Hawthorn Oak Sumac 
Beech (Thornapple)Spruce Oak, Poison Sweetgum 
Blackberry Hemlock Olive, Russian Sycamore 
Blackgum Hickory Persimmon, Eastern Tarbush 
Cedar Honeylocus! Pine Willow 
Cherry Honeysuckle Plum, Sand Witch hazel 
Chinquapin Hornbeam (WildPlum) Yaupon 
Cottonwood Huckleberry Poplar Yucca 
Creosotebush Huisache Rabbitbrush 
Dewberry Ivy, Poison Redcedar, Eastern 
Dogwood Kudzu Rose, McCartney 
15

WEEDS CONTROLLED 
ANNUALS BIENNIALS AND PERENNIALS 
COMMON NAME SCIENTIFIC NAME COMMON NAME 
Beebalm, Spotted Monarda punctata Bindweed, Field 
Broomweed, common Gutierezia dracunculoides Bittercress 
Buckwheat, Wild Polygonum convulvulus Buckeye 
Buffalobur . Solarium rostra tum Bullnettle 
Burdock Arctium spp. chicory 
Buttercup, Corn Ranunculus arvensis Clover, Hop 
Chickweed, Common Stel/aria media Dandelion 
Cockle, Corn Agrostemma githago Dock,Curly 
Cocklebur, Common Xanthium strumarium Elderberry 
Coreopsis, Plains Coreopsis tinctoria. Goldenrod, Missouri 
Croton, Woolly Croton capitatus Goldenweed, Common 
Devilsclaw proboscidea luisianica Groundsel 
Dogfennel) Cypressweed) Eupatorium capillifolium Honeysuckle, Hairy 
Eveningprimrose, Cutleaf Oenothera lacinata Horsenettle 
Flax Unum catharticum Ivy, Poison 
Fleabane, Annual Erigeren annuus Knapweed, Black 
Flixweed Descurainia sophia Russian 
Henbit Lamium amplexicauJe Spotted 
Knotweed, Prostrate Polygonum avicu/are Marshelder 
Keehia Kochia scoparia Mesquite 
Lambsquarters, Common Chenopodium a/bum Milkweed, Antelopehorn 
lettuce, Prickly Lactuca serrioJa Nightshade, Silverleaf 
Mallow, Common Malva neglecta Black 
Morningglory, Ivyleaf Ipomea hederacea Persimmon, Eastern 
Tall Ipomea purpurea Rabbitbrush 
Mustard, Annual Brassica spp. Ragwort, Tansy 
Tansy Descurainia pinnata Redvine 
Pennycress, Field Th/aspi arverse Sagebrush, Fringed 
Pepperweed, Virginia Lepidium virginicum Smartweed, Swamp 
Pigweed, Prostrate Amaranthus blitoides Sorrel, Red (Sheep Sorrel) 
Redroot Amaranthus retroflexus Sowthistle, Perennial 
Sedge Cyperus compressus Vetch 
Shepherdspurse Capsel/a bursa-pastoris Yankeeweed, 
Smartweed, Pennsylvania Polygonum pensylvanicum 
Sneezeweed, Bitter Helenium amurum 
(Wild) Helianthus annuus 
Thistle, Russian Sa/soja iberica 
Velvetleaf Abutilon teophrasti 
FOOD/FEED CROP USES 
This product can be used on the following: 
, Conservation Reserve Program land 
, Fallow Systems (Between Crop Applications) 
'General Farmstead 
Grain Sorghum 
Grass (Hay or Silage) 
Pastures 
Rangeland 
Sugarcane 
Wheat 
SCIENTIFIC NAME 
Convolvulus arvensis 
Cardamine spp. 
Aesculus spp. 
Cnidosculus stimulosus 
Cichorium intybus 
Trito/eum aureum 
Taraxacum officinale 
Rumex crispus 
Sambucus canadensis 
Solidago missouriensis 
Isocoma coronopifolia 
Senecio vulgaris 
Lonicera 
Solarium caroliniense 
Rhus radicans '. 
Centaurea nigra 
Centaurea repens 
Centaurea maculosus 
Inaannua 
Prosopis Ju/iflora 
Ascfepius 
Solanum elaeagnifolium 
Solarium nigrum 
Diospyros virginiana 
Chrysanthemus pulchellus 
Senecio jacobia 
Brunnichia ovata . 
Artemisia frigida 
Polygonum coccineum 
Rumex acetosella 
Sonchus arvensis 
Viciaspp. 
Eupatorium compositifolium 
, These crops are considered tood/feed crops only when harvested, grazed or foraged. Otherwise, they are considered as non­
food/feed uses. 
16

( 
STORAGE AND DISPOSAL 
Do not contaminate water, food or feed by storage or disposal. 
PESTICIDE STORAGE: Always store pesticides in a secured warehouse or storage building. Store at temperatures above 32°F. 
If allowed to freeze, rewarm to 40°F, remix thoroughly before using. This does not alter this product. Containers should be opened 
in well·ventilated areas. Keep container tightly sealed when not in use. Do not stack cardboard cases more than two pallets high. 
Do not store near open containers of fertilizer, seed or other pesticides. 
PESTICIDE DISPOSAL: Pesticide wastes are toxic. It container is damaged or if pesticide has leaked, contain all spillage. Absorb 
and clean up all spilled material with granules or sand. Place in a closed, labeled container for proper disposal. Improper disposal 
of excess pesticide; spray mixtures, or finsate is a violation of Federal law and may contaminate ground water. If these wastes 
cannot be disposed of by use aCcording to label instructions, contact your State Pesticide or Environmental Control Agency, or 
the Hazardous Waste Representative at the nearest EPA regional office for guidance. 
CONTAINER DISPOSAL: Triple rinse (or equivalent), adding rinsate to spray tank. Then offer for recycling or reconditioning, or 
puncture and dispose of in a sanitary landfill, or by other procedures approved by State and 'local authorities. Plastic containers 
are also disposable by incineration, or if allowed by State and local authorities, by buming. If burned, stay out of smoke. 
WARRANTY DISCLAIMER 
The directions tor use of this product must be followed carefully. TO THE EXTENT CONSISTENT WfTH APPLICABLE LAW, 
(1) THE GOODS DELIVERED TO YOU ARE FURNISHED "AS IS" BY MANUFACTURER OR SELLER AND (2) MANUFACTURER 
AND SELLER MAKE NO WARRANTIES, GUARANTEES, OR REPRESENTATIONS OF ANY KIND TO BUYER OR USER, 
EITHER EXPRESS OR IMPUED, OR BY USAGE OF TRADE, STATUTORY OR OTHERWISE, WITH REGARD TO THE PRODUCT 
SOLD, INCLUDING, BUT NOT LlMrrED TO MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, USE, OR 
ELIGIBILITY OF THE PRODUCT FOR ANY PARTICULAR TRADE USAGE. ,UNINTENDED CONSEQUENCES, INCLUDING BUT 
NOT LIMITED TO INEFFECTIVENESS, MAY RESULT BECAUSE OF. SUCH FACTORS AS THE PRESENCE OR ABSENCE OF 
OTHER MATERIALS USED IN COMBINATION WITH THE GOODS, OR THE MANNER OF USE OR APPLICATION, INCLUDING 
WEATHER, ALL OF WHICH ARE BEYOND THE CONTROL OF MANUFACTURER OR SELLER AND ASSUMED BY BUYER OR 
USER. THIS WRITING CONTAINS ALL OF THE REPRESENTATIONS AND AGREEMENTS BETWEEN BUYER, MANUFACTURER 
AND SELLER, AND NO PERSON OR AGENT OF MANUFACTURER OR SELLER HAS ANY ,AUTHORITY TO MAKE ANY 
REPRESENTATION OR WARRANTY OR AGREEMENT RELATING IN ANY WAY TO THESE.GOODS. 
LIMITATION OF LIABILITY 
TO THE EXTENT CONSISTENT WITH APPLICABLE LAW, IN NO EVENT SHALL MANUFACTURER OR SEllER BE LIABLE FOR 
SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, OR FOR DAMAGES IN THEIR NATURE OF PENALTIES RELATING 
TO THE GOODS SOLD, INCLUDING USE, APPLICATION, HANDLING, AND DISPOSAL. MANUFACTURER OR SELLER SHALL 
NOT BE LIABLE TO BUYER OR USER BY WAY OF INDEMNIFICATION TO BUYER OR TO CUSTOMERS OF BUYER, IF ANY, OR 
FOR ANY DAMAGES OR SUMS OF MONEY, CLAIMS OR DEMANDS WHATSOEVER, RESULTING FROM OR BY REASON OF, 
OR RISING OUT OF THE MISUSE, OR FAILURE TO FOLLOW LABEL WARNINGS OR INSTRUCTIONS FOR USE, OF THE 
GOODS SOLD BY MANUFACTURER OR SELLER TO BUYER. ALL SUCH RISKS SHALL BE ASSUMED BY THE BUYER, USER, 
OR ITS CUSTOMERS. BUYER'S OR USER'S EXCLUSIVE REMEDY, AND MANUFACTURER'S OR SELLER'S TOTAL LIABILITY 
SHALL BE FOR DAMAGES NOT EXCEEDING THE COST OF THE PRODUCT. 
If you do not agree with or do not accept any of directions for use, the warranty disclaimers, or limitations on liability, do 
not use the product, and return it unopened to the Seller, and the purchase price will be refunded. 
Diablo, Razor, Veteran and Patriot are registered trademarks of Nufarm America~ Inc. 
QuickSilver is a registered trademark of FMC Corporation 
17 
(RV110507A)