crop-chem-docs/corpus/epa_ppls/228-675.md

# NUFARM DIQUAT 2 L HERBICIDE

- EPA Reg No: **228-675**
- Registrant: NUFARM AMERICAS, INC.
- Signal word: Caution
- Active ingredients: Diquat dibromide (37.3%)
- Label accepted: 2026-01-27
- Source PDF: https://www3.epa.gov/pesticides/chem_search/ppls/000228-00675-20260127.pdf

---
January 27, 2026 
 
Nikki Benson 
Regulatory Manager, Crop Protection 
Nufarm Americas, Inc. 
4000 Aerial Center Parkway, Suite 101 
Morrisville, NC 27560 
 
Subject: Label Amendment - Registration Review Mitigation for Diquat Dibromide 
 Product Name: NUFARM DIQUAT 2 L HERBICIDE 
 EPA Registration Number: 228-675 
Case Number: 680153 
Application Date: November 24, 2025 
 
Dear Nikki Benson: 
 
The Agency, in accordance with the Federal Insecticide, Fungicide, and Rodenticide Act (FIFRA), 
as amended, has completed reviewing all the information submitted with your application to 
support the Registration Review of the above referenced product in connection with the Diquat 
Dibromide Interim Decision, and has concluded that your submission is acceptable. The label 
referred to above, submitted in connection with registration under FIFRA, as amended, is 
acceptable. 
 
Should you wish to add/retain a reference to the company’s website on your label, then please 
be aware that the website becomes labeling under the Federal Insecticide, Fungicide, and 
Rodenticide Act and is subject to review by the Agency. If the website is false or misleading, the 
product would be misbranded and unlawful to sell or distribute under FIFRA section 12(a)(1)(E). 
40 CFR 156.10(a)(5) list examples of statements EPA may consider false or misleading. In 
addition, regardless of whether a website is referenced on your product’s label, claims made on 
the website may not substantially differ from those claims approved through the registration 
process. Therefore, should the Agency find or if it is brought to our attention that a website 
contains false or misleading statements or claims substantially differing from the EPA approved 
registration, the website will be referred to the EPA’s Office of Enforcement and Compliance 
Assurance. 
 
A stamped copy of your labeling is enclosed for your records. This labeling supersedes 
all previously accepted labeling and must be used at your next label printing. You must 
submit one copy of the final printed labeling before you release the product for

Page 2 of 2 
EPA Reg. No. 228-675 
Case No. 680153 
 
shipment with the new labeling. In accordance with 40 CFR 152.130(c), you may 
distribute or sell this product under the previously approved labeling for 12 months 
from the date of this letter. After 12 months, you may only distribute or sell this 
product if it bears this new revised labeling or subsequently approved labeling. “To 
distribute or sell” is defined under FIFRA section 2(gg) and its implementing regulation 
at 40 CFR 152.3. 
 
If you have any questions about this letter, please contact Meaghan Robertson by phone at 
202-566-1069, or via email at robertson.meaghan@epa.gov. 
 
 Sincerely, 
 
 
Cathryn Britton 
Chief, Risk Management and Implementation 
Branch V 
Pesticide Re-evaluation Division (7508M) 
Office of Pesticide Programs 
 
ENCLOSURE: Stamped label

1
DIQUAT DIBROMIDE GROUP 22 HERBICIDE
Nufarm Diquat 2 L Herbicide
AGRICULTURAL, LANDSCAPE AND AQUATIC HERBICIDE
[ABN: Nufarm Diquat 2L Herbicide; ABN: Nufarm Diquat Pro 2 L
Herbicide; ABN: Diquat SPC 2L Herbicide; ABN: Diquat SPC 2 L 
Herbicide; ABN: Diquat SPC 2 L; ABN: Diquat SPC 2L; ABN: Nufarm 
Diquat SPC 2L Herbicide; ABN: Nufarm Diquat SPC 2 L Herbicide; 
ABN: Nufarm Diquat SPC 2L; ABN: Nufarm Diquat SPC 2 L]
TO PREVENT ACCIDENTAL POISONING, NEVER PUT THIS PRODUCT INTO FOOD, DRINK, OR 
OTHER CONTAINERS. USE THIS PRODUCT STRI CTLY IN ACCORDANCE WITH THE DIRECTIONS 
ON THIS LABEL.
Intended for Commercial Use
ACTIVE INGREDIENT:
Diquat dibromide [6,7-dihydrodipyrido(1,2-a:2’,1’-c) pyrazinediium dibromide].............................37.3%
OTHER INGREDIENTS:................................................................................................................62.7%
TOTAL: ........................................................................................................................................100.0%
Contains 2 lbs. diquat cation per gallon (3.73 lbs. of diquat dibromide per gallon).
KEEP OUT OF REACH OF CHILDREN
CAUTION/PRECAUCION
[See [back][side][panel][below][next page][inside booklet][booklet] for [First 
Aid][and][additional][Precautionary Statements][and][Directions for Use]]
For Medical Emergencies Call (877) 325-1840.
For Chemical Spill, Leak, Fire or Exposure Call CHEMTREC (800) 424-9300.
EPA Reg. No. 228-675 EPA Est. No.
Manufactured for:
Nufarm Americas Inc
11901 S. AUSTIN AVE. 
ALSIP, IL 60803
Net Contents:
000228-000675.20260120.Amend
01/27/2026
228-675

2 
PRECAUTIONARY STATEMENTS 
HAZARDS TO HUMANS AND DOMESTIC ANIMALS 
CAUTION/PRECAUCION 
Harmful if inhaled. Harmful if swallowed. Causes mo derate eye irritation. Avoid breathing spray mist. 
Avoid contact with eyes or clothing. 
PERSONAL PROTECTIVE EQUIPMENT (PPE) 
Some materials that are chemical-resistant to this product are barrier laminate, butyl rubber > 14 mils, and 
nitrile rubber > 14 mils. 
Mixers, Loaders, Applicators and other handlers must wear: 
x Coveralls over short-sleeved shirt and short pants or coveralls over long-sleeved shirt and long pants 
x Chemical-resistant gloves 
x Chemical-resistant footwear plus socks 
x Protective eyewear 
x Chemical-resistant headgear for overhead exposure 
x Chemical-resistant apron when cleaning equipment, mixing, or loading 
x Face shield when mixing or loading 
In addition: 
x applicators using groundboom equipment for all crop uses 
x mixer/loader/applicators using mechanically pre ssurized handguns, on orchards and vineyards for 
drench and soil or ground-directed sprays, on industrial and commercial areas 
x handlers supporting applications to aquatic area s for the control of submersed weeds via trailing or 
submersed hoses, during the time in which they are mixing and/or loading the diquat-containing 
material, 
x mixer/loader/applicators using backpack sprayers for treatments to rights -of-way (e.g., utilities, 
railroads, and roadways), and landscaping and turf sites (e.g., lawns, athletic fields, and parks) 
x mixer/loaders supporting applications to aquati c areas with mechanically-pressurized handguns 
x mixer/loader/applicators using mechanically-press urized handguns to treat aquatic areas, during 
mixing and loading operations ONLY: 
must wear: 
x a minimum of a NIOSH-approved particulate filt ering facepiece respirator with any N, R or P 
filter; OR 
x a NIOSH-approved elastomeric particulate re spirator with any N, R or P filter; OR 
x a NIOSH-approved powered air purifying respirator with HE filters 
Alternatively, such mixer/loaders may use closed mixing/loading systems without a respirator. A 
closed system is one which removes the pesticide from its original container and transfers the 
pesticide product through connecting hoses, pipes and couplings that are sufficiently tight to 
prevent exposure of handlers to the pesticide product, except for the negligible escape associated 
with normal operation of the system (40 CFR § 170.607(d)). 
Exception: After this product has been diluted to 0.50% or less in water (i.e., the labeled rate for some 
spot applications), applicators for AQUATIC SURFAC E APPLICATIONS must, at a minimum, wear (Note 
– Mixers and Loaders for this application method must still wear the personal protective equipment (PPE) 
as described in the above section): 
x Long-sleeved shirt and long pants 
x Shoes plus socks 
x Waterproof gloves 
x Protective eyewear 
Exception: At a minimum, applicators for AQUATIC SU BSURFACE APPLICATIONS must wear (Note – 
Mixers and Loaders for this application method must still wear the personal protective equipment (PPE) as 
described in the above section): 
x Short-sleeved shirt and short pants 
x Waterproof gloves

3 
x Chemical-resistant footwear plus socks 
Discard clothing and other absorbent materials that have been drenched or heavily contaminated with this 
product’s concentrate. Do not reuse them. Follow manufacturer’s instructions for cleaning/maintaining 
PPE. If no such instructions for washables exist, use detergent and hot water. Keep and wash PPE 
separately from other laundry. 
Respirator fit testing, medical qualification, and training 
Using a program that conforms to OSHA’s requiremen ts (see 29 CFR Part 1910.134), employers must 
verify that any handler who uses a respirator is: 
x Fit-tested and fit-checked, 
x Trained, and 
x Examined by a qualified medical practitioner to ensure physical ability to safely wear the style of 
respirator to be worn. A qualified medical practiti oner is a physician or other licensed health care 
professional who will evaluate the ability of a worker to wear a respirator. The initial evaluation 
consists of a questionnaire that asks about medical conditions (s uch as a heart condition) that 
would be problematic for respirator use. If concer ns are identified, then additional evaluations, 
such as a physical exam, might be necessary. The initial evaluation
 must be done before respirator 
use begins. Handlers must be reexamined by a qual ified medical practitioner if their health status 
or respirator style or use-conditions change. 
Upon request by local/state/federal /tribal enforcement personnel, employers must provide documentation 
demonstrating how they have complied with these requirements. 
Engineering Control Statements 
Mixers and loaders supporting aerial applications ar e required to use closed systems that provide dermal 
and inhalation protection. The closed system must be used in a manner that meets the requirements listed 
in the Worker Protection Standard (WPS) for agricultural pesticides [40 CFR 170.240(d)(4)]. 
When handlers use closed systems, enclosed cabs, or aircraft in a manner that meets the requirements 
listed in the Worker Protection Standard (WPS) for ag ricultural pesticides [40 CFR 170.240(d)(4-6)], the 
handler PPE requirements may be reduced or modified as specified in the WPS. 
USER SAFETY RECOMMENDATIONS 
Users Should: 
x Wash hands before eating, drinking, chewing gum, using tobacco or using the toilet. 
x Remove clothing/PPE immediately if pesticide gets inside. Then wash thoroughly and put on clean 
clothing. 
x Remove PPE immediately after handling this product. Wash the outside of gloves before removing. 
As soon as possible, wash thoroughly and change into clean clothing. 
 
 
 
FIRST AID 
IF IN EYES: x If in eyes, IMMEDIATELY hold eye open and rinse thoroughly and gently with 
water for 15-20 minutes. 
x Remove contact lenses, if present, after the first 5 minutes and then continue 
rinsing eye. 
x Call a poison control center or doctor for treatment advice. 
IF SWALLOWED: x Call a poison control center or doctor immediately for treatment advice. 
x Have person sip a glass of water if able to swallow. 
x Do not induce vomiting unless told to do so by the poison control center or 
doctor. 
x Do not give anything by mouth to an unconscious person. 
IF ON SKIN OR 
CLOTHING: 
x Take off contaminated clothing. 
x Rinse skin immediately with plenty of water for 15 to20 minutes. 
x Call a poison control center or doctor for treatment advice. 
IF INHALED: x Move person to fresh air.

4 
x If person is not breathing, call 911 or an ambulance, then give artificial 
respiration, preferably by mouth-to-mouth, if possible. 
x Call a poison control center or doctor for further treatment advice. 
HOT LINE NUMBER 
Have the product container or label with you when calling a poison control center or doctor, or going for 
treatment. You may also contact 1-877-325-1840 for emergency medical treatment information. 
NOTE TO PHYSICIAN 
To be effective, treatment for diquat poisoning must begin IMMEDIATELY. Treatment consists of binding 
diquat in the gut with suspensions of activated charcoal or bentonite clay, administration of cathartics to 
enhance elimination, and removal of diquat from th e blood by charcoal hemoperfusion or continuous 
hemodialysis. If in eyes, treat symptomatically. Symptoms may develop gradually. Severe damage may 
be caused by apparently trivial contact and healin g may be delayed. Medical supervision should be 
continued until healing is complete. 
ENVIRONMENTAL HAZARDS 
NON-TARGET ORGANISM ADVISORY: This product is toxic to plants and may adversely impact the 
forage and habitat of non-target organisms, including pollinators, in areas adjacent to the treated site. 
Protect the forage and habitat of non-target organisms by following label directions intended to minimize 
spray drift 
This pesticide is toxic to aquatic invertebrates. 
For Terrestrial Uses, do not apply directly to water, or to areas where surface water is present, or to 
intertidal areas below the mean high water mark. Do not contaminate water when disposing of equipment 
wash water. 
For Aquatic Uses, do not apply directly to water except as specified on this label. 
DIRECTIONS FOR USE 
It is a violation of Federal law to use this product in a manner inconsistent with its labeling. 
READ ENTIRE LABEL. USE STRICTLY IN A CCORDANCE WITH PRECAUTIONARY STATEMENTS 
AND DIRECTIONS, AND WITH APPLICABLE STATE AND FEDERAL REGULATIONS. 
Do not apply products containing diquat dibromide to production ornamentals at a rate more than 1 lb 
ai/A/year. 
Do not apply products containing diquat dibromide more than four times per year. 
Do not apply this product through any type of irrigation system. 
Do not apply this product in a way that will contact workers or other persons, either directly or through drift. 
Only protected handlers may be in the area during application. For any requirements specific to your State 
or Tribe, consult the agency responsible for pesticide regulation.

5 
 
AGRICULTURAL USE REQUIREMENTS 
Use this product only in accordance with its labeling and with the Worker Protection Standard 40 CFR Part 
170. This Standard contains requirements for the pr otection of agricultural workers on farms, forests, 
nurseries, and greenhouses, and handlers of agricultur al pesticides. It contains requirements for training, 
decontamination, notification, and emergency assistan ce. It also contains specific instructions and 
exceptions pertaining to the statements on this la bel about personal protecti ve equipment (PPE), and 
restricted-entry interval. The requirements in this box only apply to uses of this product that are covered by 
the Worker Protection Standard. 
Do not enter or allow worker entry into treated areas during the restricted-entry interval (REI) of 24 hours. 
PPE required for early entry to trea ted areas that is permitted under th e Worker Protection Standard and 
that involves contact with anything that has been treated, such as plants, soil, or water, is: 
x Coveralls over short-sleeved shirt and short pants, or coveralls over long-sleeved shirt and long pants 
x Chemical-resistant gloves made of any waterproof material 
x Chemical-resistant footwear plus socks 
x Protective eyewear 
x Chemical-resistant headgear for overhead exposure 
 
NON-AGRICULTURAL USE REQUIREMENTS 
The requirements in this box apply to uses of this product that are NOT within the scope of the Worker 
Protection Standard for agricultural pesticides (40 CFR part 170). The WPS applies when this product is 
used to produce agricultural plants on farms, forests, nurseries, or greenhouses. 
Keep all unprotected persons out of 
 
 
operating areas or vicinity where there may be drift. 
For terrestrial uses, do not enter or allow entry of maintenance workers into treated areas, or allow contact 
with treated vegetation wet with spray, dew, or rain, without appropriate protective clothing until spray has 
dried. 
For aquatic uses, do not enter treated areas while treatments are in progress. 
SPECIFIC USE DIRECTIONS 
This product is a herbicide used to control weeds in the following sites: 
x preharvest aid to desiccate labeled crops to facilitate harvesting 
x labeled nonbearing crops 
x noncrop or nonplanted areas on farms 
x aquatic areas 
x commercial greenhouses and nurseries 
x dormant established turfgrass (bermudagrass, zoysiagrass – nonfood or feed crop) 
x landscape, industrial, recreational, commercial, residential, and public areas 
x ornamental seed crops (flowers, bulbs, etc. – excluding the state of California) 
x turf renovation (all turf areas except commercial sod farms) 
 
This product works by being absorbed by the weed, and, within a few days, the weed shows signs of dying. 
Optimum results are seen if the weeds are young, actively growing, and free from stress. 
 
To avoid injury to desired crops, ornamentals or de sirable plants, use caution to prevent drift during 
application and clean all spray equipment thoroughly with water after use. Avoid application to muddy 
water or disturbing the water during application that reduce weed control. To avoid reduced herbicidal 
activity, do not use dirty or muddy water in preparing spray solutions of this product. Avoid application 
under conditions of high wind, water flow, or wave action.

6 
Do not allow sprays to come in contact with or drift to, foliage of ornamental plants or food crops. 
Do not graze livestock on treated turf or feed treated thatch to livestock. 
 
SPRAY DRIFT MANAGEMENT 
Mandatory Spray Drift Directions 
 
Aerial Applications 
x Do not release spray at a height greater than 10 ft above the vegetative canopy, unless a 
greater application height is necessary for pilot safety. 
x For all applications, applicators are required to use a medium or coarser spray droplet size 
(ASABE S572.1). 
x The boom length must not exceed 65% of the wingspan for airplanes or 75% of the rotor blade 
diameter for helicopters. 
x Applicators must use ½ swath displacement up wind at the downwind edge of the field. 
x Nozzles must be oriented so the spray is directed toward the back of the aircraft. 
x Do not apply when wind speeds exceed 10 miles per hour at the application site. 
x Do not apply during temperature inversions. 
Groundboom Applications 
x Apply with the nozzle height recommended by the manufacturer, but no more than 4 feet 
above the ground or crop canopy. 
x For all applications, applicators are required to use a medium or coarser spray droplet size 
(ASABE S572.1). 
x Do not apply when wind speeds exceed 15 miles per hour at the application site. 
x Do not apply during temperature inversions. 
Boom-less Ground Applications: 
x Applicators are required to use a medium or coarser droplet size (ASABE S572.1) for all 
applications. 
x Do not apply when wind speeds exceed 15 miles per hour at the application site. 
x Do not apply during temperature inversions. 
 
Spray Drift Advisories 
 
THE APPLICATOR IS RESPONSIBLE FOR AVOIDING OFF-SITE SPRAY DRIFT. 
BE AWARE OF NEARBY NON-TARGET SITES AND ENVIRONMENTAL CONDITIONS. 
 
IMPORTANCE OF DROPLET SIZE 
An effective way to reduce spray drift is to apply large droplets. Use the largest droplets that 
provide target pest control. While applying larger droplets will reduce spray drift, the potential for 
drift will be greater if applications are made improperly or under unfavorable environmental 
conditions. 
 
Controlling Droplet Size - Ground Boom 
x Volume - Increasing the spray volume so that larger droplets are produced will reduce spray 
drift. Use the highest practical spray volume for the application. If a greater spray volume is 
needed, consider using a nozzle with a higher flow rate. 
x Pressure - Use the lowest spray pressure recommended for the nozzle to produce the target 
spray volume and droplet size. 
x Spray Nozzle - Use a spray nozzle that is designed for the intended application. Consider using 
nozzles designed to reduce drift. 
Controlling Droplet Size - Aircraft 
x Adjust Nozzles - Follow nozzle manufacturers recommendations for setting up nozzles. 
Generally, to reduce fine droplets, nozzles should be oriented parallel with the airflow in flight.

7 
BOOM HEIGHT - Ground Boom 
Use the lowest boom height that is compatible with the spray nozzles that will provide uniform 
coverage. For ground equipment, the boom should remain level with the crop and have minimal 
bounce. 
RELEASE HEIGHT - Aircraft 
Higher release heights increase the potential for spray drift. When applying aerially to crops, do 
not release spray at a height greater than 10 ft above the crop canopy, unless a greater 
application height is necessary for pilot safety. 
SHIELDED SPRAYERS 
Shielding the boom or individual nozzles can reduce spray drift. Consider using shielded 
sprayers. Verify that the shields are not interfering with the uniform deposition of the spray on 
the target area. 
TEMPERATURE AND HUMIDITY 
When making applications in hot and dry conditions, use larger droplets to reduce effects of 
evaporation. 
TEMPERATURE INVERSIONS 
Drift potential is high during a temperature inversion. Temperature inversions are characterized 
by increasing temperature with altitude and are common on nights with limited cloud cover and 
light to no wind. The presence of an inversion can be indicated by ground fog or by the 
movement of smoke from a ground source or an aircraft smoke generator. Smoke that layers 
and moves laterally in a concentrated cloud (under low wind conditions) indicates an inversion, 
while smoke that moves upward and rapidly dissipates indicates good vertical air mixing. Avoid 
applications during temperature inversions. 
WIND 
Drift potential generally increases with wind speed. AVOID APPLICATIONS DURING GUSTY 
WIND CONDITIONS. 
Applicators need to be familiar with local wind patterns and terrain that could affect spray drift. 
Boom-less Ground Applications: 
Setting nozzles at the lowest effective height will help to reduce the potential for spray drift. 
Handheld Technology Applications: 
Take precautions to minimize spray drift. 
 
WEED RESISTANCE MANAGEMENT 
For resistance management, this prod uct contains a Group 22 herbicide – diquat dibromide. Any weed 
population may contain or develop plants naturally resistant to diquat dibr omide and other Group 22 
herbicides. The resistant biotypes may dominate th e weed population if these herbicides are used 
repeatedly in the same field. Appropriate resistance management strategies should be followed. 
 
When herbicides that affect the same biological site of action are used repeatedly over several years to 
control the same weed species in the same field, naturally-occurring resistant biotypes may survive a 
correctly applied herbicide treatment, propagate, and be come dominant in that field. Adequate control of 
these resistant weed biotypes cannot be expected. If weed control is unsatisfactory, it may be necessary 
to retreat the problem area using a product affecting a different site of action. 
 
To delay herbicide resistance take one or more of the following steps: 
 
• Rotate the use of this product or other Group 22 herbicides within a growing season sequence or among 
growing seasons with different herbicide groups that control the same weeds in a field. 
 
• Use tank mixtures with herbicides from a different group if such use is permitted; where information on 
resistance in target weed species is available, use the less resistance-prone partner at a rate that will control 
the target weed(s) equally as well as the more resi stance-prone partner. Consult your local extension 
service or certified crop advisor if you are unsure as to which active ingredient is currently less prone to 
resistance. 
 
• Adopt an integrated weed -management program for herbicide use that includes scouting and uses 
historical information related to herbicide use and cr op rotation, and that considers tillage ( or other

8 
mechanical control methods), cultural ( e.g., higher crop seeding rates; precision fertilizer application 
method and timing to favor the crop and not the weeds), biological (weed-competitive crops or varieties) 
and other management practices. 
 
• Scout after herbicide application to monitor weed po pulations for early signs of resistance development. 
Indicators of possible herbicide resistance include: (1) failure to control a weed species normally controlled 
by the herbicide at the dose applied, especially if control is achieved on adjacent weeds; (2) a spreading 
patch of non-controlled plants of a particular weed species; (3) surv iving plants mixed with controlled 
individuals of the same species. If resistance is susp ected, prevent weed seed production in the affected 
area by an alternative herbicide from a different group or by a mechanical method such as hoeing or tillage. 
Prevent movement of resistant weed seeds to other fi elds by cleaning harvesti ng and tillage equipment 
when moving between fields, and planting clean seed. 
 
• If a weed pest population continues to progress after treatment with this product, discontinue use of this 
product, and switch to another management strategy or herbicide with a different mode of action, if 
available. 
 
• Contact your local extension specialist or certifie d crop advisors for additional pesticide resistance -
management and/or integrated weed-management recommendations for specific crops and weed biotypes. 
 
• [For further information or to report suspected resistance, contact your Nufarm representative at 855-280-
6609.] 
It is advisable to keep accurate records of pesticides ap plied to individual fields to help obtain information 
on the spread and dispersal of resistant biotypes. Contact your local sales representative, crop advisor, or 
extension agent to find out if suspected resistant weeds to this MOA have been found in your region. Do 
not assume that each listed weed is being controlled by this mechanisms of action. Co-formulated active 
ingredients are intended to broaden the spectrum of weeds that are controlled. Some weeds may be 
controlled by only one of the active ingredient in this product. 
 
Suspected herbicide-resistant weeds may be identified by these indicators: 
* Failure to control a weed species normally cont rolled by the herbicide at the dose applied, 
especially if control is achieved on adjacent weeds; 
* A spreading patch of non-controlled plants of a particular weed species; and 
* Surviving plants mixed with controlled individuals of the same species. 
AGRICULTURAL USES 
Apply this product to dessicate certain crops as a prehar vest aid to facilitate harvesting. This product can 
also be applied as a general herbicide to control weeds in nonbearing crops and noncrop areas. 
This product acts on contact with actively growing gr een plant tissue and for effective control, complete 
coverage of all green plant tissue is required. Signs of herbicidal activity are usually apparent within a few 
days of application. Improper application technique and/or application to large, stressed, or mowed weeds 
will generally result in unacceptable control. Weeds that emerge after application of this product will not be 
controlled or suppressed. Weeds that are established or larger than 6” my require retreatment. 
NOTE: Cool (below 55°F) or cloudy, overcast weather will slow this product activity but will not affect 
performance. 
USE PRECAUTIONS 
x Do NOT allow spray to contact or drift to desirable vegetation or severe plant injury or death will result. 
x Do NOT use dirty or muddy water when diluting this product. 
x Do NOT apply this product through any type of irrigation system. 
x Rain or irrigation occurring within 30 minutes of application negatively impacts herbicidal activity. 
x Be sure to rinse all spray equipment thoroughly with water after use. 
As with any dessicant consider the following before use:

9 
x Premature application will result in the harvest of green seed 
x Pod drop will increase during heavy winds following application 
x Effects may be more pronounced with some varieties 
The user of this product accepts the responsibility for: 
x Knowing the sensitivity of the variety treated, 
x Properly timing the application, and 
x Accepting the risk of unfavorable weather conditions after application. 
x Human flagging is prohibited 
 
APPLICATION INSTRUCTIONS 
Apply this product to newly emerged weeds while ac tively growing and before they become too large 
(weeds 1 - 6 inches in height are easiest to control). Be sure to follow the specified rates listed in the 
specific crop instructions below, using the higher rates when weeds are large or dense or when applying 
for harvest aid and the crop vegetation is dense. 
If weeds have been mowed or grazed (removing much of the green foliage) be sure to allow weeds to 
regrow to a height of 2 - 4 inches before application. For harvest aid applications, refer to the specific crop 
instructions below for application timing specifications. 
NOTE: Because dust can coat target surfaces and re duce product activity, avoid applying in extremely 
dusty conditions (e.g., dust caused by high winds or the passage of equipment tires). 
Spray Equipment 
Be sure to follow the specific instructions for minimum spray volumes listed in the crop specific instructions 
below. Note that the specifications are minimum volumes only, and increase spray volumes as necessary 
to obtain complete coverage of the target weed or pl ant (without causing foliage runoff). For best results 
use flat fan nozzles. Other nozzles provide less than complete coverage resulting in reduced performance. 
NOTE: When spraying less than 20 gals. of spray carrier per acre, target weeds must not exceed 6 inches 
in height. 
Adjuvants 
When applying this product, be sure to always add one of the following adjuvants: 
Nonionic Surfactant (NIS) - Add a NIS containing 75% or greater surface active agent at 0.06-0.5% v/v 
(1/2 – 4 pts. per 100 gals.) of the finished spray volume. 
Other Adjuvants - Use adjuvants other than NIS but that meet the following criteria: 
x Contains only EPA exempt ingredients. 
x Is compatible when mixed with this product (compatibility can be determined using a jar test). 
x Is supported locally for use with this product thro ugh proven field trials and through university and 
extension recommendations.

10 
SPECIFIC USE INSTRUCTIONS 
Crop Use 
Pattern 
Product 
Rate per Acre 
Minimum Total 
Spray Volume per 
Acre 
Preharves
t Interval 
(Days) 
Precautions, Restrictions, and Comments 
Alfalfa (seed 
crop only) 
Preharvest 
desiccation 
broadcast 
1-1/2 to 2 pints (see 
precautions section 
for additional rate 
information) 
Ground: 15 gallons 
Air: 5 gallons 
3 On thin stands of seed alfalfa use 1 pint Per acre. 
Desiccation is complete in 3 – 10 days. 
Do not graze or feed treated forage to livestock. 
Do not use seed from treated plants for food, feed, or oil 
purposes. Do not apply products containing diquat dibromide 
more than twice per year for crop burndown on alfalfa 
Canola Preharvest 
dessication 
broadcast 
1-1/2 to 2 pints Ground: 15 gallons 
Air: 5 gallons 
7 A maximum of one application per crop is allowed. 
For best results, harvest no later than 10 days after 
application. Do not apply products containing diquat 
dibromide more than once per year for crop burndown in 
canola. 
Clover (seed 
crop only) 
Preharvest 
dessication 
broadcast 
1-1/2 to 2 pints Ground: 15 gallons 
Air: 5 gallons 
3 Desiccation is complete in 3 – 10 days. 
Do not graze or feed treated forage to livestock. 
Do not use seed from treated plants for food, feed, or oil 
purposes. Do not apply products containing diquat dibromide 
more than twice per year for clover grown for seed 
Potato Preharvest 
dessication 
broadcast 
1 to 2 pints Ground: 20 gallons 
Air: 5 gallons 
7 Do not apply to potatoes that are drought stressed. 
Make a second application if necessary to obtain additional 
desiccation where vine growth is dense. For improved vine 
coverage, a 5 day interval is recommended between applications. 
Do not apply products containing diquat dibromide more than 1 lb 
ai/A/per year for crop burndown in potatoes. 
Do not apply more than 4 pints of this product per acre.

11 
Crop Use 
Pattern 
Product 
Rate per Acre 
Minimum Total 
Spray Volume per 
Acre 
Preharvest 
Interval 
(Days) 
Precautions, Restrictions, and 
Comments 
Tree, Vine, 
Small Fruit, 
Vegetable 
Crops – 
Nonbearing 
Acerola (West 
Indian Cherry) 
Almonds 
Apple 
Apricots 
Artichokes 
Asparagus 
Avocados 
Bananas 
Blackberry 
Blueberry 
Boysenberry 
Cherries 
Coffee 
Conifers 
Crabapple 
Cranberry 
Dates 
Dewberry 
Elderberry 
Figs 
Filberts 
Ginseng 
Gooseberry 
Grapes 
Grapefruit 
Guava 
Huckleberry 
Jojoba 
Kiwi 
Lemons 
Limes 
Loganberry 
Macadamia 
Mango 
Nectarines 
Olives 
Oranges 
Papayas 
Passion Fruit 
Peaches 
Pears 
Pecans 
Persimmons 
Pistachios 
Plantains 
Plums 
Pomegranates 
Prunes 
Raspberry 
Tangelos 
Tangerines 
Walnuts 
Direct 
spray 
1-1/2 to 2 pints Ground: 15 gallons 
 
Do not use for 
food or feed 
for one (1) 
year after 
application. 
Do not graze treated area. 
Use a shield or wrap plant when 
spraying around young trees or 
vines. 
Do not allow spray to contact 
green stems, foliage, or fruit as 
injury may occur. 
Retreatment may be necessary 
for complete control of grasses 
and older established weeds. 
This product can be used 
during site preparation prior to 
planting and up to 1 year of 
harvest.

12 
 
Other Uses Use Pattern Application Rate 
Noncrop or Nonplanted 
Areas on Farms 
 
Fence lines, Farmyards, 
Farm Buildings, Fuel 
Storage Areas, Barrier 
Strips, Equipment Areas, 
and Dry (non
-flooded) 
areas around ponds, 
lakes, and drainage 
ditches.
 
Broadcast 
 
 
 
 
Spot Treatment 
1 to 2 pints . In a minimum of 15 
gallons of water per acre. 
 
 
 
1 
– 2 quarts plus the labeled rate 
of a 75% or greater nonionic 
surfactant per 100 gallons water 
or 0.75 ounces (22 ml) plus the 
labeled rate of 75% or greater 
nonionic surfactant per 1 gallon of 
water
 
Apply for full coverage and thorough 
weed control. 
Retreatment may be necessary to 
control grasses and established weeds. 
Avoid spray contact with foliage of food 
crops or ornamental plants or other 
desirable vegetation.
 
Add the labeled rate of 75% or greater 
nonionic surfactant to the finished spray 
volume. 
 
AQUATIC AND NONCROP USES 
New York – Not for Sale or Use in New York State without Supplemental Special Local Needs 
Labeling. 
This product is used to control aquatic weeds in public waters such as ponds, lakes, reservoirs, marshes, 
bayous, drainage ditches, canals, streams, rivers, and other slow-moving or quiescent bodies of water. Do 
not apply to water that is moving or if outflow leads to public waters (i.e., apply only to still water ponds, 
lakes and drainage ditches). 
Optimum control of submersed weeds is obtained by applying this product when the weeds are actively 
growing (photosynthesizing), typically when water temperatures are about 50°F or more (this occurs usually 
in the Spring or early Summer).

13 
Precautions and Restrictions: 
x Obtain all necessary approval and/or permits before application if required. Consult the responsible 
state agencies (i.e., Fish and Game Agencies, State Water Conservation authorities, or Department of 
Natural Resources). 
x Apply this product by those applicators certified for aquatic pest control authorized by the State or local 
government, Federal or State public agencies su ch as Water Management District personnel and 
municipal officials, and by Corps of Engineers. 
x For water bodies containing dense weeds, apply this pr oduct to only 1/3 to ½ of the water body area at 
one time. If a repeat application is required, wait for 14 days. Using this product in this manner will 
prevent loss of oxygen in the water body which occurs when dead weeds begin to decompose which 
often leads to suffocation of fish. 
x Do not apply this product in areas where commercial processing of fish which produces fish protein 
concentrate or fish meal is practiced. Prior to application, coordinate application with and obtain 
approval from local and/or State authorities. 
x Use water treated with this product only after the specified number of days have passed after 
application (refer to the table below for these water us e restrictions). Alternatively, use the water at a 
different time after application only if an approved assay (ex. PAM II Spectrometric Method) shows that 
no more than the designated maximum contaminant level goal (MCLG) of 0.02 mg/L (ppm) of diquat 
dibromide (calculated as the cation) is present in the water. 
x Do not apply this product on cattails ( Typha spp.) as a target weed species. 
x If posting is required by your St ate or Tribe, consult the agency responsible for pesticide regulations for 
specific details. 
x Do not apply this product at a rate greater than 2.5 lb ai/surface-acre per application for the control of 
floating, emergent, or marginal vegetation. Do not apply this product at a rate greater than 1 lb ai/acre-
foot per application for the control of submersed weeds. 
x Waters treated with this product may be hazardou s to non-target aquatic organisms. Treatment of 
aquatic weeds and algae can result in oxygen loss from decomposition of dead biomass. This oxygen 
loss can cause fish and invertebrate suffocation. To minimize this hazard, do not use products 
containing diquat dibromide to treat more than ½ of the water body (excluding water infrastructure and 
constructed conveyances such as drainage canals, ditches and pipelines or intakes and aqueducts for 
drinking water or irrigation use) to avoid depletion of oxygen due to decaying vegetation. Wait at least 
7 days between diquat dibromide applications to adjacent treatment areas within the same waterbody. 
Begin treatment along the shore and proceed outward in bands to allow fish to move into untreated 
areas. Consult with the state or local agency with primary responsibility for regulating pesticides before 
applying this product to public waters to determine if a permit is required. 
Water Use Restrictions Following Applications 
 
 Number of Days to Wait Before Using Water After An 
Application At Different Application Rates 
TYPE OF WATER 1.25 
gals./ 
surface 
acre 
1 gal./ 
surface 
acre 
0.75 gal./ 
surface 
acre 
0.50 gal./ 
surface 
acre 
Spot Spray 
(<0.5 gal./ 
surface acre)† 
Drinking 
 
3 days 2 days 2 days 1 day 1 day 
Fishing and Swimming 
 
0 0 0 0 0 
Livestock/Domestic Animals 
Consumption 
1 day 1 day 1 day 1 day 1 day 
Spray Tank Applications†† and 
Irrigation to Turf and 
Landscape Ornamentals 
3 days 2 days 2 days 1 day 1 day

14 
Spray Tank Applications†† and 
Irrigation to Food Crops and 
Production Ornamentals 
5 days 5 days 5 days 5 days 5 days 
 
†Apply this product in addition to the manufacturer’s specified rate of a nonionic surfactant 
(contains 75% or greater nonionic surfactant). 
††Do not use water treated with this product to prepare sprays to be applied to food crops, turf or 
ornamentals until the appropriate time period has elapsed or injury to crop, turf or plants could 
occur. 
Note: If more than one spray tank is required to complete a single aquatic application, there is no 
water restriction between the consecutive spray tank applications.

15 
Control of Floating and Marginal Weeds 
This product controls the listed floating and marginal weeds from application by airboat, airplane, backpack, 
spray handgun, helicopter, or similar application equipment. For all application methods, ensure that weeds 
received thorough spray coverage. 
 
Floating and Marginal Weeds Controlled 
Water lettuce, Pistia stratiotes 
Water hyacinth, Eichhornia crassipes 
Duckweed, Lemna spp. 
Salvinia spp. (including S. molesta) 
Pennywort (Hydrocotyle spp.) 
Frog’s bit, Limnobium spongia† 
†Not registered for use in California 
 
Spot Treatment: 
Application Rates: 2 quarts of this product per 100 gallons spray carrier (0.5% solution) plus 
0.25 to1.0% v/v (1 quart to 1 gallon per 100 gallons water) of an approved aquatic wetting agent. 
Application Directions: Apply spray solutions to wet completely the target weeds. Do not spray 
to runoff. Make additional applications if treating densely-packed weeds or mats. Best results are 
obtained for weed escapes if repeat applications are made within 2 weeks of the first treatment. 
 
Broadcast Treatment: 
Application Rates: 0.5 to 1.25 gallons of this product per surface acre in sufficient spray 
carrier plus 16 to 32 oz. per acre of an approved aquatic wetting agent. 
 For duckweed control: Apply this product at 1-1.25 gallons/A. 
Application Directions: Apply sprays to ensure thorough target weed coverage. Repeat 
applications as necessary for densely populated weed areas. 
 
Control of Submerged Weeds 
This product controls the listed submerged weeds from application by surface, subsurface, and bottom 
placement applications. Enhanced weed control are ob tained in situations where severe weed or algae 
infestations are found: use an approved algaecide either as a pretreatment to an application of this product, 
or as a tank mix with this product. 
 
Submersed Weeds Controlled or Suppressed 
Bladderwort, Utricularia spp. 
Hydrilla, Hydrilla verticillata 
Watermilfoils (including Eurasian), Myriophyllum spp. 
Pondweeds, Potamogeton spp.† 
Coontail, Ceratophyllum demersum 
Elodea, Elodea spp. 
Brazilian Elodea, Egeria densa 
Naiad, Najas spp. 
Algae, Spirogyra spp. and Pithophora spp.†† 
† This product does not control Richardson’s pondweed, P. richardsonii. 
††Suppression only. Spirogyra and/or Pithophora, can be controlled using 
a tank mix of this product with an approved algaecide. 
Application Rates: To control submersed weeds, apply this product at 0.5 gallon per acre-foot of water. 
Repeat applications at 14- to 21- day intervals are needed for optimum control. 
Use the table below to determine the number of gallon s of this product needed to apply per surface acre 
based on water depth.

16 
 
 
Application 
Rate 
Gallons of Product per Acre-Foot of Average Water Depth 
 
 
 1 Foot 2 Feet 3 Feet 4 Feet 
0.5 gallon/acre 
foot 
0.5 gal. 1.0 gal. 1.5 gal. 2.0 gal. 
Note: For water depths of 2 feet or less including shorelines, do not exceed 1 gallon per surface acre. 
Application Directions 
Subsurface Applications : For submersed weeds, especially Hydrilla, that have reached the 
water’s surface, apply this product in a water carrier or an invert emulsion through boom trailing hoses 
carrying nozzle tips that direct the dilute spray below the water surface to ensure adequate weed coverage. 
Bottom Placement: For submersed weeds (ex. Hydrilla, Bladderwort, or Coontail) that have 
reached the water surface and/or where the water is slowly moving through the weed growth, apply this 
product in an invert emulsion carrier with weighted ho ses that injects the diluted spray solution near the 
bottom. Adding a copper-based algaecide improves control. Alternatively, a pretreatment application with 
a copper based algaecide improves overall control if algae are present along with submersed weeds. 
Surface Application for Submersed Aquatic Weeds: For submerged weeds, apply this product 
as a spray in sufficient carrier to fully cover the target area and to ensure complete coverage of the weed 
areas. Use the higher rate for mixed weed populations. Do not use surface spray applications for densely-
packed submersed weeds or if water is over 2 feet deep (use subsurface applications of this product in 
these situations). 
The use of a vehicle-mounted boom sprayer to apply this product above the water surface for treatment of 
floating, emergent, or marginal vegetation, except for applications made via aircraft, is prohibited. This 
prohibition does not apply to applications made below the water surface via submersed or trailing hoses. 
COMMERCIAL GREENHOUSES AND NURSERIES 
Use this product for general weed control in commer cial greenhouses (ex., beneath benches), for field 
grown and container stock, and in other similar areas. Make applications of this product preplant or 
postplant preemergence in field grown ornamental nu rsery plantings, or postemergence as a directed 
spray. For ornamental seed crops (NOT registered for use in the State of California), apply this product 
preemergence. Do not allow sprays to contact desirable foliage or injury will occur. Do not use on food or 
feed crops. 
Spot Spray Application Rates: 1 to 2 qts. of this product plus a nonionic surfactant (contains 75% or 
greater nonionic surfactant) at the manufacturer’s specified rate per 100 gals of water, or 0.75 oz. (22 ml) 
of this product plus the manufacturer’s specified rate of a nonionic surfactant (contains 75% or greater 
nonionic surfactant) per 1 gallon of water. 
Broadcast Application Rates: 1 to 2 pts. of this product in a mini mum of 15 gallons of water per acre 
plus a nonionic surfactant (contains 75% or greate r nonionic surfactant) at the manufacturer’s specified 
rate per 100 gals of spray mixture. For thorough coverage, apply this product in an adequate spray volume. 
The use of mechanically-pressurized handguns to apply this product in greenhouses is prohibited. 
DORMANT ESTABLISHED TURFGRASS (BERMUDAGRASS, ZOYSIAGRASS) 
NONFOOD OR FEED CROP 
This product controls the listed emerged annual broadleaf and grass weeds in established dormant 
bermudagrass lawns, parks, golf courses, etc. Do not apply unless turfgrass is dormant at application. 
Application to actively growing bermudagrass causes de lay or permanent injury. If using this product in 
extreme Southern areas of the U.S., make certain that the turfgrass is dormant at the time of application. 
 
Weeds Controlled in Established Dormant Turfgrass 
Little Barley† 
Annual Bluegrass

17 
Bromes including Rescuegrass, Sixweeks fescue, Henbit, 
Buttercup, and Carolina Geranium 
†Apply this product before the mid-boot stage. 
 
Broadcast (Ground) Application Rates: 1 to 2 pts. of this product per acre in 20 to 100 gals. of spray 
mix plus a nonionic surfactant (contains 75% or greater nonionic surfactant) at the manufacturer’s specified 
rate per 100 gals. of spray mixture. 
LANDSCAPE, INDUSTRIAL, RECREATIONAL, COMMERCIAL, RESIDENTIAL, AND PUBLIC AREAS 
This product is a non-selective herbicide and it will kill broadleaf and grassy weeds in industrial, recreational, 
golf course, commercial, residential, and public areas within 24 to 36 hours. Do not allow sprays to contact 
desirable plant foliage or injury will occur. 
To be effective as a contact/desiccant herbicide, this product must completely cover the target weeds. Best 
results are seen when this product is applied to young, actively growing weeds. Do not apply to weeds that 
are growing under stress. Use the specified application techniques for acceptable weed control. 
For weeds that are difficult to control, such as perennial, or deeply-rooted weeds, control is often obtained 
by applications of this product as a tank mix with other systemic-type herbicides. This product, when applied 
as a tank-mix with a preemergent herbicide labeled for th e intended use site, will provide residual control. 
Before preparing large volume of a tank-mix of this pr oduct with other herbicides, check that the tank-mix 
is physically compatible by mixing only a small amount of the tank mix. If the mixture balls up, forms flakes, 
sludges, jells, oily films or layers, or other precipitates, do not use this combination: it is not compatible. 
Read and follow the other product labels for specific application directions. 
It is not possible for Nufarm to test all possible tank mixtures of this product with other pesticides for 
compatibility, efficacy, or other adverse effects. Consult your state experimental station, state university or 
extension agent before tank-mixing this product with other herbicides. 
Grounds maintenance weed control in public, commer cial and residential landscapes, including 
landscape beds, lawns, golf courses and roadsides: Apply this product as a spot or broadcast spray 
to control weeds in listed sites or to control weeds around the edges and non-flooded portions of ponds, 
lakes and ditches. 
Trim and Edge weed control along driveways, walkways, patios, cart paths, fence lines, and around 
trees, ornamental gardens, buildings, other st ructures, and beneath non-commercial greenhouse 
benches: This product can be used to eliminate undesired grass and broadleaf plant growth in narrow-
banded areas along the areas listed. 
Since this product does not translocate systemically, it can be used as an edging or pruning tool. This 
product must be applied only to the select, narrow-banded areas of grass or undesirable weed growth found 
in desirable ornamental bedding plants, ground covers , etc. This product will only control vegetation 
growing within the width of the spray application. Do not exceed the labeled rate of this product or concrete-
based materials will be stained. 
Industrial weed control for right- of-ways, railroad beds/yards, highways, roads, dividers and 
medians, parking lots, pipelines, pumping stations, public utility lines, transformer stations and 
substations, electric utilities, storag e yards, and other non-crop areas: Apply this product as a spot 
or broadcast spray either alone or in combination with other herbicides for a fast burndown of weeds in 
listed industrial weed control sites. 
Spot Spray Applications: 1 to 2 qts. of this product plus a nonionic surfactant (contains 75% or greater 
nonionic surfactant) at the manufacturer’s specified rate per 100 gals. water. For small spray solution 
volumes, mix 0.75 oz. (22 ml) this product with the appropriate amount of the nonionic surfactant in 1 gallon 
of water. 
Broadcast Applications: 1 to 2 pts. of this product per acre plus a nonionic surfactant (contains 75% or 
greater nonionic surfactant) at the manufacturer’s specified rate per 100 gals. of spray mixture. Use 
sufficient water to ensure good spray coverage, alth ough increased spray volumes (60 gals. or more) will 
be necessary for treating tall and/or dense target plants.

18 
ORNAMENTAL SEED CROPS (FLOWERS, BULBS, ETC.) 
(NOT REGISTERED FOR USE IN THE STATE OF CALIFORNIA) 
This product can be used for preharvest desiccation of ornamental seed crops. DO NOT USE FOR FOOD 
OR FIBER CROPS. 
Broadcast (Air or Ground) Applications: 1.5 to 2 pts. of this product plus a nonionic surfactant (contains 
75% or greater nonionic surfactant) at the manufacturer’s specified rate per acre. Apply in sufficient amount 
of water (minimum of 5 gallons by air; 15 gallons by ground) to ensure desiccation and weed burndown. 
Make repeat applications at a minimum of 5-day intervals and do not apply more than three applications. 
Do not use seed, screenings, or waste as feed or for consumption. 
TURF RENOVATION 
(ALL TURF AREAS EXCEPT COMMERCIAL SOD FARMS) 
This product is used to desiccate golf course turf and other turf areas prior to renovation. For suppression 
of regrowth and quick desiccation of treated turfgrass, use this product as a tank mix with other systemic 
non-selective or systemic postemergence grassy weed herbicides. Before tank mixing with other products, 
read and follow the other product labels for specific application directions and restrictions. 
Broadcast (Ground) Application: 1 to 2 pts. of this product per acre plus a nonionic surfactant (contains 
75% or greater nonionic surfactant) at the manufacturer’s specified rate in 20 to 100 gals. of water. For 
smaller spray solution volumes, mix 4 teaspoons of th is product and the appropriate amount of nonionic 
surfactant in 1 gal. of water. Apply this product as a full coverage spray to thoroughly contact the turfgrass. 
Make applications only when the turf is dry, free from dew or other moisture. Increased water volumes (100 
gal. of water per acre) will enhance turf desiccation, especially when turfgrass is dense and thick. 
STORAGE AND DISPOSAL 
Do not contaminate water, food, or feed by storage or disposal. 
PESTICIDE STORAGE: Keep pesticide in original container. Do not put concentrate or dilute into food 
or drink containers. Do not contaminate feed, foodstuffs, or drinking water. Do not store or transport near 
feed or food. Store at temperatures above 32°F. 
PESTICIDE DISPOSAL: Open dumping is prohibited. Pesticide wa stes are toxic. Improper disposal of 
excess pesticide, spray mixture, or rinsate is a violation of Federal law. If these wastes cannot be disposed 
of by use according to label instructions, contact your State Pesticide or Environmental Control Agency or 
the Hazardous Waste representative at the nearest EPA Regional Office for guidance. 
CONTAINER DISPOSAL: 
Nonrefillable Containers 5 Gallons or Less: Nonrefillable container. Do not reuse or refill this container. 
Offer for recycling if availa ble. Triple rinse container (or equivalent ) promptly after emptying. Triple rinse 
as follows: Empty the remaining contents into application equipment or a mix tank and drain for 10 seconds 
after the flow begins to drip. Fill the container 1/4 fu ll with water and recap. Shake for 10 seconds. Pour 
rinsate into application equipment or a mix tank or store rinsate for later use or disposal. Drain for 10 
seconds after the flow begins to drip. Repeat this pr ocedure two more times. Then offer for recycling or 
reconditioning, or puncture and dispose of in a sanitary landfill, or by other procedures approved by State 
and local authorities. Plastic containers are also disp osable by incineration, or, if allowed by State and 
local authorities, by burning. If burned stay out of smoke. 
Nonrefillable containers larger than 5 gallons: Nonrefillable container. Do not reuse or refill this 
container. Offer for recycling if available. If recycling or reconditioning not available, puncture and dispose 
of in a sanitary landfill, or by ot her procedures approved by State and local authorities. Plastic containers 
are also disposable by incineration, or, if allowed by State and local authorities, by burning. If burned stay 
out of smoke. Triple rinse or pressure rinse containe r (or equivalent) promptly after emptying. Triple rinse 
as follows: Empty the remaining contents into application equipment or a mix tank. Fill the container 1/4 
full with water. Replace and tighten closures. Tip contai ner on its side and roll it back and forth, ensuring 
at least one complete revolution, for 30 seconds. St and the container on its end and tip it back and forth 
several times. Turn the container over onto its other end and tip it back and forth several times. Empty the 
rinsate into application equipment or a mix tank or store rinsate for later use or disposal. Repeat this 
procedure two more times. Pressure rinse as follows: Empty the rema ining contents into application 
equipment or a mix tank and continue to drain for 10 seconds after the flow begins to drip. Hold container 
upside down over application equipment or mix tank or collect rinsate for later use or disposal. Insert

19 
pressure-rinsing nozzle in the side of the container, and rinse at about 40 psi for at least 30 seconds. Drain 
for 10 seconds after the flow begins to drip. 
Refillable containers larger than 5 gallons: Refillable container. Refill this container with pesticide only. 
Do not reuse this container for any other purpose. Cl eaning the container before final disposal is the 
responsibility of the person disposing of the container. Cleaning before refilling is the responsibility of the 
refiller. To clean the container before final disposal, empty the remaining contents from this container into 
application equipment or a mix tank. Fill the containe r about 10% full with water. Agitate vigorously or 
recirculate water with the pump for two minutes. Pour or pump rinsate into application equipment or rinsate 
collection system. Repeat this rinsing procedure two more times. 
 
CONTAINER IS NOT SAFE FOR FOOD, FEED, OR DRINKING WATER!

20 
WARRANTY DISCLAIMER 
The directions for use of this product must be followed carefully. TO THE EXTENT CONSISTENT 
WITH APPLICABLE LAW, (1) THE GOODS DELIVERED TO YOU ARE FURNISHED “AS IS” BY 
MANUFACTURER OR SELLER AND (2) MANUFACT URER AND SELLER MAKE NO WARRANTIES, 
GUARANTEES, OR REPRESENTATIONS OF ANY KIND TO BUYER OR USER, EITHER EXPRESS OR 
IMPLIED, OR BY USAGE OF TRADE, STATUTORY OR OTHERWISE, WITH REGARD TO THE 
PRODUCT SOLD, INCLUDING, BUT NOT LIMI TED TO MERCHANTABILITY, FITNESS FOR A 
PARTICULAR PURPOSE, USE, OR ELIGIBILITY OF THE PRODUCT FOR ANY PARTICULAR TRADE 
USAGE. UNINTENDED CONSEQUENCES, INCLUDING BUT NOT LIMITED TO INEFFECTIVENESS, 
MAY RESULT BECAUSE OF SUCH FACTORS AS THE PRESENCE OR ABSENCE OF OTHER 
MATERIALS USED IN COMBINATION WITH THE GOODS, OR THE MANNER OF USE OR 
APPLICATION, INCLUDING WEATHER, ALL OF WHICH ARE BEYOND THE CONTROL OF 
MANUFACTURER OR SELLER AND ASSUMED BY BUYER OR USER. THIS WRITING CONTAINS ALL 
OF THE REPRESENTATIONS AND AGREEMENTS BETWEEN BUYER, MANUFACTURER AND 
SELLER, AND NO PERSON OR AGENT OF MANUFACTURER OR SELLER HAS ANY AUTHORITY TO 
MAKE ANY REPRESENTATION OR WARRANTY OR AGREEMENT RELATING IN ANY WAY TO THESE 
GOODS. 
 
LIMITATION OF LIABILITY 
TO THE EXTENT CONSISTENT WITH APPLICABLE LAW, IN NO EVENT SHALL MANUFACTURER OR 
SELLER BE LIABLE FOR SPECIAL, INCIDENT AL, OR CONSEQUENTIAL DAMAGES, OR FOR 
DAMAGES IN THEIR NATURE OF PENALTIES RE LATING TO THE GOODS SOLD, INCLUDING USE, 
APPLICATION, HANDLING, AND DISPOSAL. TO THE EXTENT CONSISTENT WITH APPLICABLE LAW, 
MANUFACTURER OR SELLER SHALL NOT BE LIABLE TO BUYER OR USER BY WAY OF 
INDEMNIFICATION TO BUYER OR TO CUSTOMERS OF BUYER, IF ANY, OR FOR ANY DAMAGES OR 
SUMS OF MONEY, CLAIMS OR DEMANDS WHATSOEVER, RESULTING FROM OR BY REASON OF, 
OR RISING OUT OF THE MISUSE, OR FAILURE TO FOLLOW LABEL WARNINGS OR INSTRUCTIONS 
FOR USE, OF THE GOODS SOLD BY MANUFACTURER OR SELLER TO BUYER. ALL SUCH RISKS 
SHALL BE ASSUMED BY THE BUYER, USER, OR ITS CUSTOMERS. TO THE EXTENT CONSISTENT 
WITH APPLICABLE LAW, BUYER'S OR USER'S EXCLUSIVE REMEDY, AND MANUFACTURER'S OR 
SELLER'S TOTAL LIABILITY SHALL BE FOR DAMAGES NOT EXCEEDING THE COST OF THE 
PRODUCT. 
 
If you do not agree with or do not accept any of directions for use, the warranty disclaimers, or 
limitations on liability, do not use the product, and return it unopened to the Seller, and the purchase 
price will be refunded. 
 (RV[xxxxxx]) 
Nufarm Diquat SPC 2 L Herbicide is not manufactured or distributed by Syngenta, seller of Reglone
® and 
Reward®. 
 
Reglone
® and Reward® are trademarks of a Syngenta Group Company.