crop-chem-docs/corpus/epa_ppls/264-860.md

# LAUDIS HERBICIDE

- EPA Reg No: **264-860**
- Registrant: BAYER CROPSCIENCE, LLC
- Signal word: Caution
- Active ingredients: Tembotrione (34.5%)
- Label accepted: 2018-09-21
- Source PDF: https://www3.epa.gov/pesticides/chem_search/ppls/000264-00860-20180921.pdf

---
UNITED STATES ENVIRONMENTAL PROTECTION AGENCY 
 WASHINGTON, DC 20460 
 
 
 
Notification Label Acceptable v.20150904 
OFFICE OF CHEMICAL SAFETY 
AND POLLUTION PREVENTION 
September 21, 2018 
 
Karen Cain 
Senior Regulatory Manager 
Bayer CropScience, LP 
2 T.W. Alexander 
Research Triangle Park, NC 27709 
 
Subject: Notification per PRN 98-10 – Adding weeds to “Not for use in CA” section 
 Product Name: Laudis Herbicide 
 EPA Registration Number: 264-860 
 Application Date: March 21, 2018 
 Decision Number: 544477 
 
Dear Ms. Cain: 
 
The Agency is in receipt of your Application for Pesticide Notification under Pesticide Registration 
Notice (PRN) 98-10 for the above referenced product. The Registration Division (RD) has conducted a 
review of this request for its applicability under PRN 98-10 and finds that the action requested falls within 
the scope of PRN 98-10. The label submitted with the application has been stamped “Notification” and 
will be placed in our records. 
 
Should you wish to add/retain a reference to the company’s website on your label, then please be aware 
that the website becomes labeling under the Federal Insecticide Fungicide and Rodenticide Act and is 
subject to review by the Agency. If the website is false or misleading, the product would be misbranded 
and unlawful to sell or distribute under FIFRA section 12(a)(1)(E). 40 CFR 156.10(a)(5) list examples of 
statements EPA may consider false or misleading. In addition, regardless of whether a website is 
referenced on your product’s label, claims made on the website may not substantially differ from those 
claims approved through the registration process. Therefore, should the Agency find or if it is brought to 
our attention that a website contains false or misleading statements or claims substantially differing from 
the EPA approved registration, the website will be referred to the EPA’s Office of Enforcement and 
Compliance. 
 
If you have any questions, you may contact me at 703-305-1243 or via email at 
montague.kathryn@epa.gov . 
 
 
 
Sincerely, 
 
Kathryn Montague, Product Manager 23 
Herbicide Branch 
Registration Division (7505P) 
Office of Pesticide Programs

1
GROUP 27 HERBICIDE
LAUDIS® Herbicide 
A Herbicide for control of annual broadleaf and grass weeds in field and silage corn, seed corn, 
sweet corn, and popcorn and for postharvest burndown weed control.
ACTIVE INGREDIENT:
Tembotrione: 2-[2-chloro-4-(methylsulfonyl)-3-[(2,2,2-trifluoroethoxy)methyl]benzoyl]-1,3-cyclohexanedione * ..........................34.5%
OTHER INGREDIENTS: ................................................................................................................................................................65.5%
TOTAL: 100.0%
Contains 3.5 lb of active ingredient per gallon
*(CAS Number 335104-84-2) 
EPA Reg No. 264-860 E.P.A. Est. No.
KEEP OUT OF REACH OF CHILDREN
CAUTION
Si usted no entiende la etiqueta, busque a alguien para que se la explique a usted en detalle.
(If you do not understand the label, find someone to explain it to you in detail.)
For MEDICAL And TRANSPORTATION Emergencies ONLY Call 24 Hours A Day 1-800-334-7577
For PRODUCT USE Information Call 1-866-99BAYER (1-866-992-2937)
Please refer to [back panel] [booklet] for additional precautionary statements and directions for use. [Note to 
reviewer: Location of additional precautionary statements and directions for use will vary between those listed, 
depending on container type/size.]
FIRST AID
IF SWALLOWED: • Call a poison control center or doctor immediately for treatment advice.
• Have person sip a glass of water if able to swallow.
• Do not induce vomiting unless told to do so by a poison control center or doctor.
• Do not give anything by mouth to an unconscious person.
IF IN EYES: • Hold eye open and rinse slowly and gently with water for 15-20 minutes.
• Remove contact lenses, if present, after the first 5 minutes, then continue rinsing eye.
• Call a poison control center or doctor for treatment advice.
For MEDICAL Emergencies Call 24 Hours A Day 1-800-334-7577.
Have the product container or label with you when calling a poison control center or doctor or going for treatment.
264-860
09/21/2018

2
PRECAUTIONARY STATEMENTS
HAZARD TO HUMANS AND DOMESTIC ANIMALS
CAUTION
Harmful if swallowed. Causes moderate eye irritation. Avoid contact with eyes, skin or clothing. Wash thoroughly with soap and water 
after handling and before eating, drinking, chewing gum, or using tobacco. 
Personal Protective Equipment (PPE)
Some materials that are chemical-resistant to this product are listed below. 
Applicators and other handlers must wear: Long-sleeved shirt and long pants, socks, shoes, chemical-resistant gloves made of any 
waterproof material and protective eyewear.
Follow manufacturer's instructions for cleaning/maintaining PPE. If no such instructions for washables exist, use detergent and hot 
water. Keep and wash PPE separately from other laundry.
Engineering control statement
When handlers use closed systems, such as enclosed cabs, in a manner that meets the requirements listed in the Worker Protectio n 
Standard (WPS) for agricultural pesticides [(40 CFR §170.240(d)(4-6)], the handler PPE requirements may be reduced or modified as 
specified in the WPS.
User Safety Recommendations
• Users should remove clothing/PPE immediately if pesticide gets inside. Then wash thoroughly and put on clean clothing. 
• Users should remove PPE immediately after handling this product. Wash the outside of gloves before removing. As soon as 
possible, wash thoroughly and change into clean clothing. 
• Users should wash hands before eating, drinking, chewing gum, using tobacco or using the toilet.
ENVIRONMENTAL HAZARDS
This product is toxic to non-target plants. Do not apply directly to water, to areas where surface water is present or to inter tidal areas 
below the mean high water mark. Do not contaminate water when cleaning equipment or disposing of equipment washwaters or 
rinsate.
This product may contaminate water through drift of spray in wind. Follow precautions for use to avoid wind spray drift.
This product has a high potential for runoff after application. Poorly draining soils and soils with shallow water tables are m ore prone to 
produce runoff that contains this product. A level, well-maintained vegetative buffer strip between areas to which this product is applied 
and surface water features such as ponds, streams and springs will reduce the potential for contamination of water from runoff. Runoff 
of this product will be reduced by avoiding applications when rainfall is forecasted to occur within 48 hours. Sound erosion co ntrol 
practices will reduce this product’s contribution to surface water contamination.
This chemical has properties and characteristics associated with chemicals detected in ground water. The use of this chemical i n areas 
where soils are permeable, particularly where the water table is shallow, may result in ground-water contamination.

3
DIRECTIONS FOR USE
It is a violation of Federal law to use this product in a manner inconsistent with its labeling.
Read entire label before using this product.
Do not apply this product in a way that will contact workers or other persons, either directly or through drift. Only protected handlers 
may be in the same area during application. For any requirements specific to your State or Tribe, consult the agency responsibl e for 
pesticides.
AGRICULTURAL USE REQUIREMENTS
Use this product only in accordance with its labeling and with the Worker Protection Standard, 40 CFR part 170. This standard contains 
requirements for the protection of agricultural workers on farms, forests, nurseries, and greenhouses, and handlers of agricultural 
pesticides. It contains requirements for training, decontamination, notification and emergency assistance. It also contains specific 
instructions and exceptions pertaining to the statements on this label about personal protective equipment (PPE) and restricted entry 
intervals. The requirements in this box only apply to uses of this product that are covered by the Worker Protection Standard.
Do not enter or allow worker entry into treated areas during the restricted entry interval (REI) of 12 hours.
PPE that is required for early entry to treated areas that is permitted under the Worker Protection Standard and that involves contact 
with anything that has been treated such as plants, soil or water, is coveralls over long-sleeved shirt and long pants, socks and shoes 
and chemical-resistant gloves made of any waterproof material. 
PRODUCT INFORMATION
LAUDIS® Herbicide is intended for postemergence application in field corn (including silage corn, seed corn), sweet corn, and popcorn 
for the control of annual broadleaf and grass weeds and for postharvest burndown weed control. Weed growth ceases within hours 
after LAUDIS Herbicide is applied. Symptoms on susceptible weed species progress from yellowing and bleaching to necrosis resulting 
in eventual plant death generally within 7 to 14 days after application.
WEED CONTROL INFORMATION
LAUDIS Herbicide effectively controls a broad array of grass and broadleaf weeds, including biotypes resistant to glyphosate-,triazine-, 
phenoxy-, benzoic-, and ALS-inhibiting herbicides, when applied at 3 fl oz/A along with the recommended adjuvant system (Tables 1 
and 2). Best control of broadleaf weeds is achieved when weeds are less than 6” in height and actively growing. The best control of 
grass weeds is achieved prior to tillering and when grasses are actively growing. In corn, the addition of atrazine at a minimum 0.5 lb 
ai/A will improve control of broadleaf weeds larger than 6 “ in height and increase the speed, spectrum, and consistency of grass 
control. Always follow the most restrictive use rates and use instructions listed on the labeling of all tank mix partners. It is the pesticide 
user’s responsibility to ensure that all products in the listed mixtures are registered for the intended use. Users must follow the most 
restrictive directions and precautionary language of the products in the mixture (for example, first aid from one product, spray drift 
management from another).

4
Table 1. Broadleaf Weeds Controlled
LAUDIS Alone
3 fl oz/A
LAUDIS 3 fl oz/A + 
atrazine min. 0.5 lb 
ai/A
For All Labelled 
Uses
For Use on Corn 
Only
Broadleaf Weeds
Common Name
Scientific Name
Control of weeds <6” tall
Amaranth, palmer* Amaranthus palmeri CC
Amaranth, Powell* Amaranthus powellii CC
Amaranth, spiny* Amaranthus spinosus CC
Amaranth, tumbleweed* Amaranthus albus CC
Buckwheat, wild Polygonum 
convolvulus PC C
Buffalobur Solanum rostratium CC
Burcucumber Sicyos angulatus PC PC
Canada thistle Cirsium arvensis PC C
Carpetweed Mullugo verticillata CC
Chickweed, common Stellaria media CC
Cocklebur, common Xanthium strumarium CC
Dandelion Taraxacum officinale PC PC
Deadnettle, purple Lamium purpureum CC
Dock, curly Rumex crispus PC PC
Galinsoga* Galinsoga parviflora CC
Hemp Cannabis sativa CC
Henbit Lamium amplexicaule CC
Jimsonweed Datura stramonium CC
Knotweed, prostrate Polygonum aviculare PC PC
Kochia Kochia scoparia CC
Ladysthumb Polygonum persicaria CC
Lambsquarters, common Chenopodium album CC
Mallow, Venice Hibiscus trionum CC
Marestail/Horseweed Conyza canadensis PC C
Marshelder, common* Iva xanthifolia PC C
Morningglory, cotton* Ipomoea trichocarpa PC C
Morningglory, ivyleaf* Ipomoea hederacea PC C
Morningglory, pitted* Ipomoea lacunosa PC C
Mustard, wild Sinapis arvensis CC
Nightshade, black* Solanum nigrum CC
Nightshade, Eastern black* Solanum ptycanthum CC
Nightshade, hairy* Solanum sarrachoides CC
Pigweed, redroot Amaranthus 
retroflexus CC
Pigweed, smooth Amaranthus hybridus CC
Pokeweed, common* Phytolacca americana PC PC
Potato, volunteer Solanum spp. CC
Purslane, common Portulaca oleracea NC C
Pusley, Florida* Richardia scabra C1 C1
Ragweed, common Ambrosia 
artemisiifolia CC

5
Broadleaf Weeds
Common Name
LAUDIS Alone
3 fl oz/A
LAUDIS 3 fl oz/A + 
atrazine min. 0.5 lb 
ai/A
For All Labelled 
Uses
For Use on Corn 
Only
Scientific Name Control of weeds <6” tall
Ragweed, giant Ambrosia trifida CC
Sesbania, hemp Sesbania exaltata CC
Shepherd’s-purse* Capsella bursa-
pastoris CC
Sicklepod Cassia tora PC C
Sida, prickly (teaweed) Sida spinosa NC C
Smartweed, pale Polygonum 
lapathifolium CC
Smartweed, Pennsylvania Polygonum 
pensylvanicum CC
Sunflower, common Helianthus annuus CC
Thistle, Russian Salsola kali CC
Velvetleaf Abutilon theophrasti CC
Waterhemp, common* Amaranthus rudis CC
Waterhemp, tall* Amaranthus 
tuberculatus CC
Wormwood, biennial* Artemisia biennis CC
1Apply before weed exceeds 2 inches in height.
 C= Control PC=Partial Control 2 NC= Not controlled
2 Partially controlled weeds will be stunted in growth and/or be reduced in number as 
compared to non-treated areas; performance may not be commercially acceptable. 
The degree of weed control will vary with weed size, density, spray coverage, and/or 
growing conditions.
*Not Approved in California

6
Table 2. Grass Weeds Controlled
LAUDIS 3 fl oz/A LAUDIS 3 fl oz/A + atrazine 
min. 0.5 lb ai/A
Grass Weeds Scientific Name
For All Labelled Uses For Use on Corn Only
Maximum 
Weed 
Height 
(inches)
Performance Maximum 
Weed 
Height 
(inches)
Performance
Barnyardgrass Echinochloa 
crus-galli 5C6 C
Crabgrass, large Digitaria 
sanguinalis 3C4 C
Crabgrass, smooth Digitaria 
ischaemum 2P C2 P C
Cupgrass, woolly Eriochloa villosa 3C4 C
Foxtail, giant Setaria faberi 3C4 C
Foxtail, green Setaria viridis 2P C2 P C
Foxtail, yellow Setaria pumila 3C4 C
Goosegrass* Eleusine indica 3C4 C
Johnsongrass, 
seeding*
Sorghum 
halepense 5C6 C
Junglerice Echinochloa 
colonum 4C5 C
Lovegrass, tufted* Eragrostis pilosa 4C4 C
Millet, wild proso Panicum 
miliaceum 4C5 C
Panicum, Texas Panicum 
texanum 3C4 C
Sandbur, field Cenchrus 
incertus 2P C2 P C
Shattercane / vol. 
sorghum*
Sorghum bicolor 6C8 C
Signalgrass, 
broadleaf
Brachiaria 
platyphylla 4C5 C
C= Control PC= Partial control 2
2 Partially controlled weeds will be stunted in growth and/or be reduced in number as 
compared to non-treated areas; performance may not be commercially acceptable. 
The degree of weed control will vary with weed size, density, spray coverage, and/or 
growing conditions.
*Not Approved in California
Cultivation
Cultivation can help remove suppressed weeds or multiple flushing weeds. However, cultivation should not be performed within 7 days 
of an application of LAUDIS Herbicide as this could decrease the effectiveness of weed control due to disruption of herbicide 
translocation in the plant.

7
RESISTANCE MANAGEMENT
This product is a Group 27 herbicide. A given weed population may contain or develop resistance to a herbicide after repeated use. 
Appropriate resistance-management strategies should be followed to mitigate or delay resistance. The following Integrated Weed 
Management Techniques are effective in reducing problems with herbicide resistant weed biotypes. It is best to use multiple practices 
to manage or delay resistance, as no single strategy is likely to be totally effective.
• Rotate crops. Crop rotation diversifies weed management.
• Rotate Herbicide-tolerant traits. Alternate herbicide tolerant traits and or use HT trait stacks for more efficient rotations
• Rotate and tankmix modes of action. Use tankmix partners and multiple MOAs during both the growing season and from 
year to year to reduce the selection pressure of a single MOA
• Know your weeds, know your field. Closely monitor problematic areas with difficult to control weeds or dense weed 
populations
• Start with clean fields. Effective tillage or the use of a burndown herbicide program can control emerged weeds prior to 
planting
• Stay clean – use residual herbicides. Regardless of tillage system, a pre emergence or early postemergence soil –applied 
residual herbicide should be used.
• Apply herbicides correctly. Ensure proper application, correct timing, full-use rates and appropriate spray volumes
• Control weed escapes. Consider spot herbicide application, row wicking, cultivation, hand removal of weeds or other 
techniques to stop weed seed production and improve weed management.
• Zero Tolerance – reduce the weed seed bank. Do not allow surviving weeds to set seed, which will help decrease weed 
populations from year to year and prevent major weed shifts.
• Clean Equipment. Prevent the spread of herbicide resistant weeds and seeds
Contact your local extension specialist, certified crop advisory and /or Bayer CropScience representative for additional resistance 
management or IPM recommendation. Also for more information on Weed Resistance Management, visit the Herbicide Resistance 
Action Committee (HRAC) on the web at http://www.hracglobal.com.

8
ROTATIONAL CROP RESTRICTIONS
If a corn crop has been destroyed by hail or other means soon after a LAUDIS Herbicide application, field corn, sweet corn, or popcorn 
can be replanted immediately after a LAUDIS Herbicide application. See chart below for rotational interval to all other crops a fter a 
LAUDIS Herbicide application. Planting at shorter than specified intervals will result in injury to the rotational crop
Table 3. Rotational Crop Guidelines
Immediate 4 months 8 months 10 months 11 months 12 months 18 months
Field corn
Sweet corn
Popcorn
Cereal grains 
(except corn and 
sorghum)
Sugarcane
Grass grown for 
seed
Timothy
Soybean
Onion3
Sorghum
Peas
Rice
Cotton
Potatoes
Canola
Alfalfa
Tomato
Snapbeans
Sugar beets1, 2
Sunflowers
Dry beans1 (types 
and varieties for 
commercial 
production except 
those listed under 
18 months) 
Peanut Tobacco Cucurbits
Dry beans (red 
kidney, cranberry 
bean, non-
commercial 
“garden” types 
and varieties)
All other crops
4
1 Cumulative precipitation between application of LAUDIS Herbicide and replanting to sugar beets or dry beans must total 20 inches.
Furrow or flood irrigation cannot be included in the total. The amount of cumulative precipitation required before planting a rotational 
crop is in addition to the required rotational interval given in months.
2 Thorough tillage should follow the crop in which LAUDIS Herbicide was used and precede the rotation to sugar beets.
3 This plantback interval requires that onion crops be grown under irrigated conditions. The plantback interval for non-irrigated onion 
is 18 months
 4 All other crops may be seeded only after the completion of a successful bioassay after a LAUDIS Herbicide application. Refer to the 
“Field/Small Scale Bioassay” section.
Cover Crops
Use of cover crops as a means of soil improvement, erosion control, weed and/or insect suppression, etc., following harvest of corn in 
the Fall is increasing. Planting of cover crops in fields treated with LAUDIS Herbicide is allowed as long as these cover crops are not 
grazed by livestock nor harvested for food. Cover crops are to be tilled under or chemically controlled with burndown herbicides in the 
spring. Many cover crops can be planted within 90-120 days after application of LAUDIS Herbicide. However, all potential cover crops 
have not been evaluated for tolerance to LAUDIS Herbicide and significant injury may occur. Prior to seeding a cover crop, complete a 
successful field/small scale bioassay to provide an indication of the level of tolerance to the prior LAUDIS Herbicide application. Refer 
to the “Field/Small Scale Bioassay” section. If used in tank mixtures with other herbicides, always follow the most restrictive label.
Field/Small Scale Bioassay
A field/small scale bioassay must be completed before rotating to a crop other than those specified in the Rotational Crop Restrictions 
section of this label. To conduct an effective field bioassay, grow strips of the crop(s) you intend to grow in the following season in a 
field previously treated with LAUDIS Herbicide. The test strip should be placed in a controlled area and should include variations in soil 
such as type and pH. Crop response to the bioassay will determine if the crop(s) grown in the test strips can be grown safely in the 
areas previously treated with LAUDIS Herbicide.
For an effective small scale bioassay, collect uniform samples of all soil types from the LAUDIS Herbicide-treated field and place the 
soil into a sturdy container. Plant the desired cover crop into the soil, apply water and place the container in a warm sunny area to 
allow germination and growth of the crop. Monitor growth of the cover crop over a three to four week period. If the crop emerges and 
grows normally, the risk to establish and grow the cover crop in the LAUDIS Herbicide-treated field should be tolerable.

9
SPRAY DRIFT MANAGEMENT
Spray drift may result in injury to non target crops or vegetation. To avoid spray drift, do not apply when wind speed is greater than 10 
MPH or during periods of temperature inversions. Do not apply when weather conditions, wind speed or wind direction may cause 
spray drift to non-target areas. AVOIDING SPRAY DRIFT AT THE APPLICATION SITE IS THE RESPONSIBILITY OF THE 
APPLICATOR.
Sensitive Areas
Only apply this product when the potential for drift to adjacent sensitive areas (e.g. residential areas, bodies of water, known habitat for 
threatened or endangered species, non target crops) is minimal (e.g. when wind is 10 MPH or less and is blowing away from sensitive 
areas).
Avoiding spray drift at the application site is the responsibility of the applicator. The interaction of many equipment-and-wea ther-related 
factors determine the potential for spray drift. The applicator and the grower are responsible for considering all these factor s when 
making decisions.
Do not apply under circumstances where possible drift to unprotected persons, or to food, forage, or other plantings that might be 
damaged, as crops thereof may be rendered unfit for sale, use or consumption.
Information On Droplet Size
The most effective way to reduce drift potential is to apply large droplets. The best drift management strategy is to apply the largest 
droplets that still provide sufficient weed coverage and control. Applying larger droplets will reduce drift potential, but wil l not prevent 
drift if applications are made improperly, or under unfavorable environmental conditions (see Wind, Temperature and Humidity, a nd 
Temperature Inversion sections below).
Uniform, thorough spray coverage is important to achieve consistent weed control. Select nozzles and pressure that deliver MEDIUM 
spray droplets as indicated in nozzle manufacturer’s catalogs and in accordance with ASAE Standard S-572. Nozzles that deliver 
COARSE spray droplets may be used to reduce spray drift provided spray volume per acre (GPA) is increased to maintain coverage of 
weeds.
Controlling Droplet Size
• Volume - Use high flow rate nozzles to apply the highest practical spray volume. Nozzles with higher rated flows produce 
larger droplets.
• Pressure - Do not exceed the nozzle manufacturer’s recommended pressures. For many nozzle types lower pressure 
produces larger droplets. When higher flow rates are needed, use higher flow rate nozzles instead of increasing pressure.
• Number of nozzles - Use the minimum number of nozzles that provide uniform coverage.
• Nozzle Type - Use a nozzle type that is designed for the intended application. With most nozzle types, narrower spray angles 
produce larger droplets. Consider using low-drift nozzles. Solid stream nozzles oriented straight back produce the largest 
droplets and the lowest drift.
Application Height
For ground boom applications, apply with nozzle height no more than 15 inches above the ground or crop canopy.
Wind
Drift potential is lowest between wind speeds of 2 - 10 mph. However, many factors, including droplet size and equipment type 
determine drift potential at any given speed. Local terrain can influence wind patterns. Every applicator should be familiar wi th local 
wind patterns and how they affect spray drift.
Temperature and Humidity
When making applications in low relative humidity, set up equipment to produce larger droplets to compensate for evaporation. D roplet 
evaporation is most severe when conditions are both hot and dry. Avoid spraying during conditions of low humidity and/or high 
temperatures.

10
Temperature Inversion 
Do not make applications into areas of temperature inversion. Temperature inversion restricts vertical air mixing, which causes small 
suspended droplets to remain in a concentrated cloud. This cloud can move in unpredictable directions due to the light variable winds 
common during inversion. Temperature inversion is characterized by an increasing temperature with altitude and is common on nig hts 
with limited cloud cover and light to no wind. It begins to form as the sun sets and often continues into the morning. Its pres ence can be 
indicated by ground fog; however, if fog is not present, inversion can also be identified by the movement of smoke from a groun d 
source. Smoke that layers and moves laterally in a concentrated cloud (under low wind conditions) indicates an inversion, while smoke 
that moves upward and rapidly dissipates indicates good vertical air mixing.
APPLICATION INFORMATION
LAUDIS Herbicide may be applied by ground application only. Uniform, thorough spray coverage is important to achieve consisten t 
weed control. Select nozzles and pressure that deliver MEDIUM spray droplets as indicated in nozzle manufacturer’s catalogs and in 
accordance with ASAE Standard S-572. Nozzles that deliver COARSE spray droplets may be used to reduce spray drift provided spra y 
volume per acre (GPA) is increased to maintain coverage of weeds. Flat fan nozzles of 80° or 110° are recommended for optimum 
postemergence coverage.
• Do not use nozzles that produce FINE (e.g. - Cone) or EXTRA COARSE (e.g. - Flood jet) spray droplets.
Ground Application
LAUDIS Herbicide can be applied broadcast in a minimum of 10 gallons of water per acre (unless a higher volume is specified for a 
tank-mix partner). For weed control in dense weed populations or under adverse growing conditions, 15 to 20 gallons of water pe r acre 
is recommended. Good coverage is essential to achieve optimum weed control.
Typically, flat-fan nozzles operated at 30-60 PSI will deliver MEDIUM spray droplets, providing optimum spray coverage and cano py 
penetration. Lower pressure operation and/or higher volume flat fan nozzles typically deliver COARSE sprays. Refer to nozzle 
manufacturer catalogs. 
• Boom height should be based on the height of the crop – at least 15 inches above the crop canopy.
• Air induction nozzles should be used at or near 80 psi to produce a medium droplet size.
• Proper agitation should be maintained within the tank to keep the product dispersed.
• See the Spray Drift Management section of this label for additional information on proper application of LAUDIS Herbicide.
COMPATIBILITY
If LAUDIS Herbicide is to be tank mixed with other pesticides, compatibility must be tested prior to mixing. To test for compat ibility, use 
a small container and mix a small amount (0.5 to 1qt) of spray, combining all ingredients in the same ratio as the anticipated use. If any 
indications of physical incompatibility develop, do not use this mixture for spraying. Indications of incompatibility usually o ccur within 5-
15 minutes after mixing. If the mixture balls-up, forms flakes, sludges, gels, oily film or layers, or other precipitates, it i s not compatible 
and the tank mix combination should not be used.
MIXING INSTRUCTIONS
LAUDIS Herbicide must be applied with clean and properly calibrated equipment. Prior to adding LAUDIS Herbicide, ensure that th e 
spray tank, filters and nozzles have been thoroughly cleaned and that agitation system is properly working.
1. Fill spray tank with 50% of the required volume of water, and begin agitation.
2. Agitate the LAUDIS Herbicide product container thoroughly by shaking, circulating or stirring prior to adding the herbicide i nto 
the spray tank.
3. Add the appropriate amount of LAUDIS Herbicide slowly to the spray tank or mixing system and ensure complete dispersion. 
Maintain and ensure thorough dispersion and sufficient agitation during both mixing and spraying.
4. If tank mixing with another pesticide, add the tank mix product next (except in the case of glyphosate which should be added 
after the nitrogen fertilizer is dispersed).
5. Add nitrogen fertilizer.
6. Add the adjuvant.
7. Fill the spray tank with balance of water needed.

11
SPRAY ADDITIVES
LAUDIS Herbicide is a suspension concentrate that requires the use of an external federally approved surfactant and a nitrogen 
fertilizer source to achieve optimum weed control. For specific adjuvant recommendations with tank mixes, see the Tank Mix section of 
this label.
Federally Approved Surfactant
The use of a Methylated Seed Oil (MSO) is recommended when LAUDIS Herbicide is used or when alternative adjuvants are not 
otherwise specified on this label. MSO can improve control of weeds under stress, in high populations, in mixed grass and broadleaf 
weed populations, and under conditions of low humidity. Use MSO at 1 gallon per 100 gallons of water (1% v/v). MSO should contain at 
least 80% MSO and 10% emulsifier or greater. The use of adjuvants such as non-ionic federally approved surfactants or refined 
vegetable oils will result in unacceptable or erratic weed control.
As an alternative to traditional MSO federally approved surfactants, High federally approved Surfactant oil Concentrates (HSOC) at 
specified rates may be used with LAUDIS Herbicide. An HSOC is an emulsifiable oil based product containing 25-50% federally 
approved surfactant (wt/wt) in a minimum of 50% oil (wt/wt). The oil concentrates in HSOC can be based on MSO or COC. MSO based 
products are preferred with LAUDIS Herbicide particularly when used alone or with atrazine.
Ammonium Nitrogen Fertilizer
Use 1.5 qt/A of a high-quality urea ammonium nitrate (UAN) or 1.5 lb/A (8.5 lb per 100 gallons) of a spray-grade ammonium sulfate 
(AMS). Use UAN under conditions of low relative humidity for greater weed control.
TANK CLEANOUT PROCEDURES
(Cleaning Equipment after LAUDIS Herbicide Application)
Special attention must be given to cleaning equipment before spraying a crop other than corn. Mix only as much cleaning solution as 
needed.
1. Remove, dump and clean main sump and boom strainers in a standard commercial tank cleaner solution.
2. Disassemble nozzle bodies including screens, gaskets, and diaphragm caps and clean in a standard commercial tank cleaner 
solution.
3. Rinse walls of tank and all surfaces of tank to remove visible residue.
4. Reassemble nozzles and strainers.
5. Flush the system with clean water.
6. Add 25-50 gallons of water to spray tank. Add 1-2 gallons of household bleach to spray tank (1 gallon bleach for 25 gallons 
water). Start agitation in the sprayer and re-circulate the bleach-containing solution for 15 minutes. 
7. Spray out the bleach-containing solution until the tank is empty.
8. Rinse machine with clean water.
9. Dispose of all rinsate in an appropriate manner. 
PRECAUTIONS FOR USE
1. LAUDIS Herbicide is rainfast 1 hour after application to most weed species. Avoid application if rainfall is predicted during this 
period. Rainfall within 1 hour of application may necessitate retreatment with LAUDIS Herbicide or may result in reduced weed 
control. 
2. Weed control may be reduced if the application is made when weeds are dust covered or in the presence of heavy dew, fog, 
and mist/rain or when weeds are under stress due to drought.
3. Apply LAUDIS Herbicide spray mixtures within 24 hours of mixing to avoid product degradation.
4. Avoid drift onto adjacent crops.
5. When weeds are stressed due to drought, heat, lack of fertility, flooding, or prolonged cool temperatures control can be 
reduced or delayed because weeds are not actively growing. To obtain optimum weed control, apply LAUDIS Herbicide when 
weeds are actively growing.
6. If applying LAUDIS Herbicide or any solo post emergence HPPD herbicide (Callisto, Armezon, Impact, etc) after a HPPD-
containing product has been applied preplant/pre-emergence, always tankmix the post emergence HPPD herbicide with an 
additional effective mode of action herbicide(s). Refer to the Resistance Management section for additional specific 
precautions to help prevent weed resistance to this product.

12
RESTRICTIONS FOR USE
1. DO NOT apply when wind causes drift to off-site vegetation as injury may occur. LAUDIS Herbicide delivered via drift or tank 
contamination can cause severe damage to other crops. Careful management of spray drift and tank cleanout is required. 
2. Field corn, sweet corn, or popcorn can be planted immediately after an application of LAUDIS Herbicide. DO NOT plant other 
rotational crops immediately following LAUDIS Herbicide application. For all other crops refer to the Rotational Crop 
Restrictions section of this label.
3. DO NOT apply LAUDIS Herbicide with liquid fertilizers as the primary spray carrier. Only apply with water as the primary spra y 
carrier plus recommended adjuvants. See spray adjuvants section.
4. DO NOT apply this product by air or through any type of irrigation system.
SPECIFIC CROP USE DIRECTIONS
CORN
(Field Corn, Popcorn, Seed Corn and Sweet Corn)
LAUDIS Herbicide can be applied postemergence on all types of corn. Best results are obtained when it is applied to young, actively 
growing weeds. LAUDIS Herbicide will affect weeds that are larger than the recommended height; however it may result in incomplete 
weed control.
• Apply LAUDIS Herbicide at 3 fl oz/A per application. Always add the appropriate adjuvants to the spray tank (see Spray 
Additives information section of this label).
• Applications of LAUDIS Herbicide at rates less than 3 fl oz/A postemergence may result in incomplete weed control and 
reduction in residual activity.
• Broadcast applications of LAUDIS Herbicide must be made to corn from emergence up to the V8 stage of growth for field corn 
or popcorn, or from emergence up to the V7 stage of growth for sweet corn. 
• A second postemergence application may be made to field corn or popcorn. Applications of this product must be made a 
minimum of 7 days apart.
• Sweet Corn, Seed Corn and Popcorn Only - Herbicide sensitivity in all hybrids and inbreds of seed corn, sweet corn
and popcorn has not been tested. Consult with your seed provider, your local Bayer CropScience representative and/or other 
knowledgeable agricultural professionals for advice on hybrid/inbred tolerance before applying LAUDIS Herbicide. If the 
tolerance of a hybrid/inbred is not known, apply LAUDIS Herbicide to a small area to first determine if the hybrid/inbred is 
tolerant prior to spraying large acreages of that hybrid/inbred. As an example, do not use LAUDIS Herbicide on Merit or
Shogun sweet corn varieties as unacceptable crop response will occur.
Late or Rescue Applications
Applications of LAUDIS Herbicide at 3 fl oz/A may be applied to escaped weeds beyond labeled weed heights. In these situations, only 
partial weed control and reduced weed competition can be expected. Apply up to the V9 stage of growth for field corn or popcorn, or up 
to the V7 stage of growth for sweet corn. 
 Crop – Specific Restrictions 
• DO NOT apply LAUDIS Herbicide to corn that exhibits injury from previous herbicides applications.
• Do NOT exceed a total of 6 fl oz/A of LAUDIS Herbicide (0.16 lb ai) per growing season on field corn or popcorn, or 3 fl oz/A 
(0.08 lb ai) per growing season on sweet corn.
• DO NOT apply more than two applications of LAUDIS Herbicide to field corn or popcorn, or more than one application to sweet 
corn, per growing season. 
• If a second application of Laudis is made (field corn and popcorn only), the application must be made a minimum of 7 days 
after the first application.
• DO NOT graze livestock or harvest corn forage within 45 days of application.
Tank Mix Recommendations
Certain tank mixes may aid in the performance of LAUDIS Herbicide. See Spray Adjuvant section of this label for use recommendations 
for use with all tank mix partners used in conjunction with LAUDIS Herbicide unless otherwise specified in the following tank mix 
directions. When using LAUDIS Herbicide in tank mix combinations, refer to individual product labels for precautionary statements, 
restrictions, rates, approved used and a list of weeds controlled and follow the directions of the most restrictive label. 
Atrazine

13
An application of LAUDIS Herbicide at 3 fl oz/A in combination with atrazine at 0.5 lb ai/A will increase the speed of control, weed 
spectrum and consistency of control. Do not use atrazine if corn is greater than 12 inches tall. 
Liberty® 280 SL
LAUDIS Herbicide at 3 fl oz/A can be tank mixed with Liberty® 280 SL Herbicide at 22 fl oz/A. Liberty® 280 SL Herbicide can only be 
used on corn seed designated as LibertyLink®. Apply in a minimum of 15 gallons of water per acre. Do not use MSO/ESO or COC 
adjuvants in this mixture, only add AMS at 8.5 lbs/100 gallons (1.5 lb/A).
Define™ SC
LAUDIS Herbicide at 3 fl oz/A can be tank mixed with Define™ SC at 7 to 15 fl oz/A for additional residual weed control on corn up to 
the 5 leaf stage. 
DiFlexx® 
LAUDIS Herbicide at 3 fl oz/A can be tank mixed with DiFlexx® Herbicide for improved broadleaf weed control. Do not apply beyond the 
V9 growth stage of corn. 
Glyphosate (including Roundup and Touchdown branded products)
LAUDIS Herbicide at 3 fl oz/A can be tank mixed with glyphosate for use on glyphosate-tolerant corn. LAUDIS Herbicide will enhance 
control of broadleaf and glyphosate-resistant weeds, and will reduce glyphosate induced weed shifts. LAUDIS Herbicide should be 
added to the water in the tank and dispersed first prior to adding ammonium sulfate, glyphosate or any other pesticide or adjuvant. 
Follow all other directions on the glyphosate label regarding adjuvants and mixing instructions with loaded (adjuvant-containing) 
formulations of glyphosate. When tank mixing LAUDIS Herbicide with full use rates of a loaded glyphosate formulation, the addition of a 
glyphosate-compatible federally approved surfactant is recommended. When tankmixing LAUDIS Herbicide with full use rates of a low 
loaded or unloaded glyphosate formulations, the addition of a glyphosate-compatible federally approved surfactant is required. 
Glyphosate-compatible oil-based federally approved surfactants such as HSOC's will optimize the performance of LAUDIS Herbicide in 
the combinations. Only glyphosate-compatible oil-based federally approved surfactant (such as HSOC) may be used when mixing 
LAUDIS Herbicide plus reduced rates of glyphosate (loaded or unloaded formulations), or when applying tank mixtures of LAUDIS 
Herbicide plus glyphosate (loaded or unloaded formulations) under arid climatic conditions. 
Accent
®, Accent® Q, Option®, Stout®, Steadfast®, Steadfast® Q, Realm™ Q, Resolve® Q, or Require® Q
LAUDIS Herbicide at 3 fl oz/A can be tank mixed with Accent, Accent Q, Option, Stout, Steadfast, Steadfast Q, 
Realm Q, Resolve Q, or Require Q.
Acetamide-containing products
LAUDIS Herbicide at 3 fl oz/A can be tank mixed with certain water-based acetamide or acetamide-containing products such as 
Anthem, Anthem ATZ, Degree, Degree Xtra, Warrant, and Zidua for improved residual control of certain hard-to-control, long 
germination window weeds such as waterhemp, Palmer amaranth. Do not use Anthem ATZ or Degree Xtra if corn is greater than 12 
inches tall. Include adjuvants as described under the Spray Additives section of this label.
Buctril
® and equivalent bromoxynil products
To aid in the control of certain broadleaf weeds (e.g. ragweeds), LAUDIS Herbicide 3 fl oz/A can be tank mixed with Buctril at a rate up 
to 6 fl oz/A. Buctril can be used in place of atrazine in corn that is greater than 12 inches tall, which is the corn height limit for the use of 
atrazine. The use of crop oil concentration (COC) or MSO at 1% v/v + UAN at 1.5 qt/A or AMS at 8.5 lb/100 gal is recommended with 
tank mixture of LAUDIS Herbicide and Buctril.
Status® and other dicamba-containing products
LAUDIS Herbicide at 3 fl oz/A can be tank mixed with Status® or other dicamba-containing products for improved broadleaf weed 
control. Do not apply beyond the V9 growth stage of corn. 
Tank Mixtures for Insect Control
To provide weed and insect control in corn, LAUDIS Herbicide may be mixed with foliar insecticides including the following:
Ambush® Decis ® 
Asana® XL Lorsban ® Warrior™ 
Baythroid® XL Mustang ® Oberon ®
Capture® Pounce ® 3.2EC 
Tank Mixtures for Disease Control
To provide weed and disease control in corn, LAUDIS Herbicide may be mixed with foliar fungicides including the following:
Headline® Quilt ® Stratego® YLD
Headline AMP™ Quilt Xcel™

14
POST HARVEST BURNDOWN APPLICATION 
LAUDIS Herbicide may be used as a postharvest burndown treatment to control broadleaf weeds at any time of the year following 
harvest of corn or before planting of the next rotational crop. Laudis Herbicide will be especially effective against broadleaf weed 
biotypes which have developed resistance to glyphosate-, triazine-, ALS-inhibiting, growth regulant- and other herbicide modes of 
action. Specific rotational crop intervals must be observed between the postharvest application of Lauids Herbicide and planting of the 
next rotated crop. Refer to the ROTATIONAL CROP RESTRICTIONS found in the PRODUCT INFORMATION section of this label for 
specific crop rotation intervals.
Application Rates and Timings
Apply LAUDIS Herbicide as a broadcast postemergence spray at 3 fl oz/A plus recommended adjuvant system (refer to the Spray 
Additives information section of this label. Best weed control will be achieved when applications are made to young, actively growing 
weeds (refer to WEED CONTROL TABLE 1 in the PRODUCT INFORMATION section for a complete listing of weeds controlled)
Crop – Specific Restrictions 
• DO NOT exceed a maximum seasonal cumulative amount of 6 fl oz/A of LAUDIS Herbicide (0.16 lb ai) per growing season on 
field corn or popcorn, or 3.0 fl oz/A (0.08 lb ai) per growing season on sweet corn.
• If applying LAUDIS Herbicide postharvest, only corn (field, sweet and pop) may be planted immediately. Refer to the 
ROTATIONAL CROP RESTRICTIONS for specific crop rotation intervals.
• DO NOT graze livestock or harvest corn forage within 45 days of application.
 Tank Mixture Recommendations
Certain tank mixtures may aid in the performance of LAUDIS Herbicide as a postharvest spray application. LAUDIS Herbicide at 3 fl 
oz/A may be tank mixed with the following herbicides at their labeled use rates: 
2,4-D Dicamba Distinct ® herbicide Liberty ® 280 SL Herbicide
Clarity® herbicide DiFlexx ® Herbicide glyphosate
When using LAUDIS Herbicide in tank mix combinations, refer to individual product labels for precautionary statements, restrict ions, 
rates weed controlled and approved uses and follow the directions of the most restrictive label.

15
STORAGE AND DISPOSAL
Do not contaminate water, food or feed by storage or disposal. 
PESTICIDE STORAGE
Keep container tightly closed when not in use. Avoid cross contamination with other pesticides.
PESTICIDE DISPOSAL
Wastes resulting from the use of this product may be disposed of on site or at an approved waste disposal facility. Improper di sposal of 
excess pesticide, spray mixture, or rinsate is a violation of Federal law. For questions about proper disposal, contact your st ate 
pesticide and environmental control agency.
CONTAINER HANDLING
Rigid, Non-refillable containers less than 5 gallons 
Nonrefillable container. Do not reuse or refill this container. Offer for recycling, if available. Triple rinse container (or e quivalent) 
promptly after emptying. Triple rinse as follows: Empty the remaining contents into application equipment or a mix tank and dra in for 10 
seconds after the flow begins to drip. Fill the container ¼ full with water and recap. Shake for 10 seconds. Pour rinsate into application 
equipment or a mix tank or store rinsate for later use or disposal. Drain for 10 seconds after the flow begins to drip. Repeat this 
procedure two more times. After triple rinsing procedure dispose of container in a sanitary landfill, or by incineration; or, i f allowed by 
State and local authorities, by burning. If burned, stay out of smoke.
Rigid Non-refillable containers that are too large to shake (i.e., with capacities greater than 5 gallons or 50 lbs)
Non-refillable containers - Do not reuse or refill this container. Refer to Bottom Discharge IBC or Top Discharge IBC, Drums, Kegs 
information as follows.
Bottom Discharge IBC (e.g. – Schuetz Caged IBC or Snyder Square Stackable)
Pressure rinsing the container before final disposal is the responsibility of the person disposing of the container. To pressure rinse the 
container before final disposal, empty the remaining contents from the IBC into application equipment or mix tank. Raise the bottom of 
the IBC by 1.5 inches on the side which is opposite of the bottom discharge valve to promote more complete product removal. 
Completely remove the top lid of the IBC. Use water pressurized to at least 40 PSI to rinse all interior portions. Continuously pump or 
drain rinsate into application equipment or rinsate collection system while pressure rinsing. Continue pressure rinsing for 2 minutes or 
until rinsate becomes clear. Replace the lid and close bottom valve.
Top Discharge IBC, Drums, Kegs (e.g.– Snyder 120 Next Gen, Bonar B120, Drums, Kegs).
Triple rinsing the container before final disposal is the responsibility of the person disposing of the container. To triple rinse the 
container before final disposal, empty the remaining contents from this container into application equipment or mix tank. Fill the 
container at least 10 percent full with water. Agitate vigorously or recirculate water with the pump for 2 minutes. Rinse all interior 
surfaces. Pour or pump rinsate into application equipment or rinsate collection system. Repeat this procedure two more times.
Once container is rinsed, offer for recycling if available or puncture and dispose of in a sanitary landfill or by incineration. 
Rigid, Refillable containers less than 5 gallons 
Refillable container. Refill this container with pesticide only. Do not reuse this container for any other purpose. Cleaning th e container 
before final disposal is the responsibility of the person disposing of the container. Cleaning before refilling is the responsi bility of the 
refiller. To clean the container before final disposal, empty the remaining contents from this container into application equip ment or mix 
tank. Fill the container about 10 percent full with water. Agitate vigorously or recirculate water with the pump for 2 minutes. Pour or 
pump rinsate into application equipment or rinsate collection system. Repeat this rinsing procedure two more times. Once contai ner is 
rinsed, offer for recycling if available or puncture and dispose of in a sanitary landfill, or incineration, or if allowed by s tate and local 
authorities, by burning. If burned stay out of smoke.
Refillable Containers with capacities greater than 5 gallons or 50 lbs
Refillable container – Refer to Bottom Discharge IBC or Top Discharge IBC, Drums, Kegs information as follows. Refill this container 
with pesticide only. Do not reuse this container for any other purpose. Contact your Ag retailer or Bayer CropScience for container 
return, disposal and recycling information.
Bottom Discharge IBC (e.g. – Schuetz Caged IBC or Snyder Square Stackable)
Pressure rinsing the container before final disposal is the responsibility of the person disposing of the container. Cleaning before 
refilling is the responsibility of the refiller. To pressure rinse the container before final disposal, empty the remaining contents from the 
IBC into application equipment or mix tank. Raise the bottom of the IBC by 1.5 inches on the side which is opposite of the bottom 
discharge valve to promote more complete product removal. Completely remove the top lid of the IBC. Use water pressurized to at least 
40 PSI to rinse all interior portions. Continuously pump or drain rinsate into application equipment or rinsate collection system while 
pressure rinsing. Continue pressure rinsing for 2 minutes or until rinsate becomes clear. Replace the lid and close bottom valve.
Top Discharge IBC, Drums, Kegs (e.g.– Snyder 120 Next Gen, Bonar B120, Drums, Kegs).
Triple rinsing the container before final disposal is the responsibility of the person disposing of the container. Cleaning bef ore refilling is 
the responsibility of the refiller. To triple rinse the containers before final disposal, empty the remaining contents from thi s container into 
application equipment or mix tank. Fill the container at least 10 percent full with water. Agitate vigorously or recirculate wa ter with the 
pump for 2 minutes. Rinse all interior surfaces. Pour or pump rinsate into application equipment or rinsate collection system. Repeat 
this procedure two more times. 
Once container is rinsed, offer for recycling if available or puncture and dispose of in a sanitary landfill or by incineration.

16
End users are authorized to remove tamper evident cables as required to remove the product from the container unless the contai ner is 
equipped with one way valves and refilling or returning is planned. If this is the case, end users are not authorized to remov e tamper 
evident cables, one way valves or clean container. 
WARRANTY AND DISCLAIMER
IMPORTANT: READ BEFORE USE
Read the entire Directions for Use, Conditions, Disclaimer of Warranties and Limitations of Liability before using this product . If terms 
are not acceptable, return the unopened product container at once.
By using this product, user or buyer accepts the following Conditions, Disclaimer of Warranties and Limitations of Liability.
CONDITIONS: The directions for use of this product are believed to be adequate and must be followed carefully. However, it is 
impossible to eliminate all risks associated with the use of this product. Crop injury, ineffectiveness or other unintended con sequences 
may result because of such factors as weather conditions, presence of other materials, or the manner of use or application, all of which 
are beyond the control of Bayer CropScience. To the extent consistent with applicable law, all such risks shall be assumed by t he user 
or buyer.
DISCLAIMER OF WARRANTIES: TO THE EXTENT CONSISTENT WITH APPLICABLE LAW, BAYER CROPSCIENCE MAKES NO 
OTHER WARRANTIES, EXPRESS OR IMPLIED, OF MERCHANTABILITY OR OF FITNESS FOR A PARTICULAR PURPOSE OR 
OTHERWISE, THAT EXTEND BEYOND THE STATEMENTS MADE ON THIS LABEL. No agent of Bayer CropScience is authorized to 
make any warranties beyond those contained herein or to modify the warranties contained herein. TO THE EXTENT CONSISTENT 
WITH APPLICABLE LAW, BAYER CROPSCIENCE DISCLAIMS ANY LIABILITY WHATSOEVER FOR SPECIAL, INCIDENTAL OR 
CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OR HANDLING OF THIS PRODUCT.
LIMITATIONS OF LIABILITY: TO THE EXTENT CONSISTENT WITH APPLICABLE LAW, THE EXCLUSIVE REMEDY OF THE 
USER OR BUYER FOR ANY AND ALL LOSSES, INJURIES OR DA MAGES RESULTING FROM THE USE OR HANDLING OF THIS 
PRODUCT, WHETHER IN CONTRACT, WARRANTY, TORT, NEGLIGENCE, STRICT LIABILITY OR OTHERWISE, SHALL NOT 
EXCEED THE PURCHASE PRICE PAID, OR AT BAYER CROPSCIENCE’S ELECTION, THE REPLACEMENT OF PRODUCT. 
NET CONTENTS: Various Sizes
Asana® XL Insecticide, Accent®, Accent® Q, Status® , Stout®, Steadfast®, Steadfast® Q, Realm™ Q, Resolve® Q, or Require® Q are 
registered trademarks of E.I. DuPont DeNuemers.
Stratego
® YLD fungicide, Baythroid® Insecticide, Decis® Insecticide, Oberon® Insecticide/Miticide, Buctril® Herbicide, Define™ SC, 
DiFlexx® Herbicide, Liberty® 280 SL Herbicide, and Option® Corn Herbicide are registered trademarks of Bayer CropScience LP.
Capture®, Mustang®, Pounce® 3.2EC Insecticide, Anthem®, and Anthem® AT2 are registered trademarks of FMC Corporation.
Lorsban® is a registered trademark of Dow Agro Sciences LLC.
Headline® fungicide, Headline AMP® fungicide, Status™, Clarity® herbicide, Distinct®, Status®, and Zidua® are registered trademarks of 
BASF.
Ambush® Insecticide, Warrior® Insecticide, Quilt® fungicide and Quilt Xcel® fungicide are registered trademarks of Syngenta Group 
Company.
Degree®, Degree Extra®, and Warrant® are registered trademarks of Monsanto Company.
Produced for
Bayer CropScience LP
P.O. Box 12014, 2 T.W. Alexander Drive
Research Triangle Park, North Carolina 27709
1-866-99BAYER (1-866-992-2937)
LAUDIS Herbicide
 (PENDING) 03/01/2018