crop-chem-docs/corpus/epa_ppls/279-9601.md

# AFFINITY BROADSPEC HERBICIDE WITH TOTALSOL SOLUBLE GRANULES

- EPA Reg No: **279-9601**
- Registrant: FMC CORPORATION 
- Signal word: Caution
- Active ingredients: Thifensulfuron (25%); Tribenuron-methyl (25%)
- Label accepted: 2019-07-09
- Source PDF: https://www3.epa.gov/pesticides/chem_search/ppls/000279-09601-20190709.pdf

---
UNITED STATES ENVIRONMENTAL PROTECTION AGENCY 
 WASHINGTON, DC 20460 
 
 
 
Reg Review Label Acceptable v.20151230 
OFFICE OF CHEMICAL SAFETY 
AND POLLUTION PREVENTION 
July 9, 2019 
 
Edward Bockrath 
Product Registration Manager 
FMC Corporation 
c/o FMC Stine Research Center 
1090 Elkton Road 
Newark, Delaware 19711 
 
 
Subject: Registration Review La bel Mitigation for Thifensulfuron-methyl and Tribenuron-
methyl 
 Product Name: Affinity Broadspec Herbicide with TotalSol S oluble Granules 
 Application Date: 12/18/2017 
 EPA Registration Number: 279-9601 
 Decision Number: 545368; 552872 
 
Dear Mr. Bockrath: 
 
The Agency, in accordance with the Federal Insecticide, Fungicide and Rodenticide Act 
(FIFRA), as amended, has completed reviewing all of the information submitted with your 
application to support the Registration Review of the above referenced product in connection 
with the 22 Sulfonylurea (SU) Herbicides Interim Decision, and has concluded that your 
submission is acceptable. The label referred to above, submitted in connection with registration 
under FIFRA, as amended, is acceptable. 
 
Should you wish to add/retain a reference to the company’s website on your label, then please be 
aware that the website becomes labeling under the Federal Insecticide Fungicide and Rodenticide 
Act and is subject to review by the Agency. If the website is false or misleading, the product 
would be misbranded and unlawful to sell or distribute under FIFRA section 12(a)(1)(E). 40 
CFR 156.10(a)(5) list examples of statements EPA may consider false or misleading. In addition, 
regardless of whether a website is referenced on your product’s label, claims made on the 
website may not substantially differ from those claims approved through the registration process. 
Therefore, should the Agency find or if it is brought to our attention that a website contains false 
or misleading statements or claims substantially differing from the EPA approved registration, 
the website will be referred to the EPA’s Office of Enforcement and Compliance. 
 
A copy of your label stamped “Accepted” is enclosed. Products shipped after 12 months from the 
date of this amendment must bear the new revised label. Your release for shipment of the 
product bearing the amended label constitutes acceptance of these conditions. If these conditions 
are not complied with, the registration will be subject to cancellation in accordance with FIFRA 
section 6.

Page 2 of 2 
EPA Reg. No. 279-9601 
Decision No. 545368; 552872 
 
If you have any questions about this letter, please contact Erik Kraft by phone at 703-308-9358, 
or via email at kraft.erik@epa.gov. 
 
 
 
 
Enclosure 
 
Sincerely, 
 
 
Erik Kraft, Product Manager 24 
Fungicide and Herbicide Branch 
Registration Division (7505P) 
Office of Pesticide Programs

1 
 
 
THIFENSULFURON METHYL GROUP 2 HERBICIDE
TRIBENURON METHYL GROUP 2 HERBICIDE
Soluble Granule
For Use on Wheat (including durum), Barley, Oats, Triticale and Fallow
Active Ingredients By Weight
Thifensulfuron-methyl
Methyl 3-[[[[(4-methoxy-6-methyl-1,3,5-triazin-2-yl) amino]carbonyl]amino]sulfonyl]-2-thiophenecarboxylate 25%
Tribenuron-methyl
Methyl 2-[[[[N-(4-methoxy-6-methyl-1,3,5-triazin-2-yl)methylamino]carbonyl]amino]sulfonyl]benzoate 25%
Other Ingredients 50%
TOTAL 1 00.0%
Contains 0.25 lb Thifensulfuron Methyl per pound
Contains 0.25 lb Tribenuron Methyl per pound
EPA Reg. No. 279-9601
Nonrefillable Container Refillable Container EPA Est. No. ___________
Net: ______________ OR Net: ______________
KEEP OUT OF REACH OF CHILDREN
CAUTION
Si usted no entiende la etiqueta, busque a alguien para que se la explique a usted en detalle. (If you do not 
understand this label, find someone to explain it to you in detail.)
FIRST AID
IF ON SKIN OR CLOTHING: Take off contaminated clothing. Rinse skin immediately with plenty of water for 
15-20 minutes. Call a poison control center or doctor for treatment advice.
Have the product container or label with you when calling a poison control center or doctor, or going for treatment. 
You may also contact 1-800-331-3148 for emergency medical treatment information.
PRECAUTIONARY STATEMENTS
HAZARDS TO HUMANS AND DOMESTIC ANIMALS
CAUTION! Harmful if absorbed through skin. Avoid contact with eyes, skin, or clothing. Prolonged or frequently 
repeated skin contact may cause allergic reactions in some individuals. Wash thoroughly with soap and water after 
handling and before eating, drinking, chewing gum, using tobacco, or using the toilet.
For medical emergencies involving this product, call toll free 1-800-331-3148.
Sold By
FMC Corporation
2929 Walnut Street
Philadelphia, PA 19104
07/09/2019
279-9601

2 
 
PERSONAL PROTECTIVE EQUIPMENT (PPE)
Applicators and other handlers must wear:
Long-sleeved shirt and long pants.
Chemical Resistant Gloves >14 mls.
Shoes plus socks.
Follow manufacturer's instructions for cleaning/maintaining PPE. If no such instructions for washables exist, use 
detergent and hot water. Keep and wash PPE separately from other laundry.
USER SAFETY RECOMMENDATIONS
USERS SHOULD: Wash hands before eating, drinking, chewing gum, using tobacco or using the toilet. Remove
clothing/PPE immediately if pesticide gets inside. Then wash thoroughly and put on clean clothing. Remove PPE
immediately after handling this product. Wash the outside of gloves before removing. As soon as possible, wash
thoroughly and change into clean clothing.
ENVIRONMENTAL HAZARDS
Do not apply directly to water, or to areas where surface water is present, or to intertidal areas below the mean high 
water mark. Do not contaminate water when cleaning equipment or disposing of equipment washwaters or rinsate.
Groundwater Advisory
This product has properties and characteristics associated with chemicals detected in groundwater. This product may 
leach into groundwater if used in areas where soils are permeable, particularly where the water table is shallow.
Surface Water Advisory
This product may impact surface water quality due to runoff of rain water. This is especially true for poorly draining 
soils and soils with shallow ground water. This product is classified as having high potential for reaching surface 
water via runoff for several weeks or more after application. A level, well-maintained vegetative buffer strip 
between areas to which this product is applied and surface water features such as ponds, streams, and springs will 
reduce the potential loading of this product from runoff water and sediment. Runoff of this product will be greatly 
reduced by avoiding applications when rainfall or irrigation is expected to occur within 48 hours.
Windblown Soil Particles Advisory
This product has the potential to move off-site due to wind erosion. Soils that are subject to wind erosion usually 
have a high silt and/or fine to very fine sand fractions and low organic matter content. Other factors which can affect
the movement of windblown soil include the intensity and direction of prevailing winds, vegetative cover, site slope, 
rainfall, and drainage patterns. Avoid applying this product if prevailing local conditions may be expected to result 
in off-site movement.
Non-target Organism Advisory
This product is toxic to plants and may adversely impact the forage and habitat of non-target organisms, including
pollinators, in areas adjacent to the treated area. Protect the forage and habitat of non-target organisms by
minimizing spray drift. For further guidance and instructions on how to minimize spray drift, refer to the Spray Drift 
Management section of this label.
PRODUCT INFORMATION
AFFINITY® BroadSpec herbicide (with TotalSol® soluble granules) – referred to below as AFFINITY BroadSpec 
herbicide - is a soluble granule that is used for selective postemergence weed control in wheat (including
durum), barley, oats, triticale and fallow. The best control is obtained when AFFINITY BroadSpec herbicide is 
applied to young, actively growing weeds. The use rate will depend on weed spectrum and size of weed at time of 
application. The degree and duration of control may depend on the following:
• weed spectrum and infestation intensity
• weed size at application
• environmental conditions at and following treatment
AFFINITY BroadSpec herbicide is noncorrosive, nonflammable, nonvolatile, and does not freeze. AFFINITY 
BroadSpec herbicide must be mixed, and completely dissolved in water and applied as a uniform broadcast spray.

3 
 
DIRECTIONS FOR USE
It is a violation of federal law to use this product in a manner inconsistent with its labeling.
Do not apply this product in a way that will contact workers or other persons, either directly or through drift. Only 
protected handlers may be in the area during application. For any requirements specific to your State or Tribe, 
consult the agency responsible for pesticide regulation.
AFFINITY BroadSpec herbicide must be used only in accordance with instructions on this label. To the extent 
consistent with applicable law, FMC will not be responsible for losses or damage resulting from the use of this 
product in any manner not specifically specified by FMC.
AFFINITY BroadSpec herbicide is for use on wheat (including durum), barley, oats, triticale and fallow in many 
states. Check with your state extension or Dept. of Agriculture before use, to be certain AFFINITY BroadSpec 
herbicide is registered in your state.
READ ENTIRE LABEL. USE STRICTLY IN ACCORDANCE WITH PRECAUTIONAR Y
STATEMENTS AND DIRECTIONS, AND WITH APPLICABLE STATE AND FEDERA L REGULATIONS.
AGRICULTURAL USE REQUIREMENTS
Use this product only in accordance with its labeling and with the Worker Protection Standard, 40 CFR part 170. 
This Standard contains requirements for the protection of agricultural workers on farms, forests, nurseries, and 
greenhouses, and handlers of agricultural pesticides. It contains requirements for training, decontamination, 
notification, and emergency assistance. It also contains specific instructions and exceptions pertaining to the 
statements on this label about personal protective equipment (PPE) and restricted-entry interval. The requirements in 
this box only apply to uses of this product that are covered by the Worker Protection Standard.
Do not enter or allow worker entry into treated areas during the restricted entry interval (REI) of 12 hours.
PPE required for early entry to treated areas that is permitted under the Worker Protection Standard and that 
involves contact with anything that has been treated, including plants, soil, or water, is:
Coveralls.
Chemical-resistant gloves made of any waterproof material.
Shoes plus socks.
RESTRICTIONS
Injury to or loss of adjacent sensitive crops, desirable trees or vegetation may result from failure to observe the 
following:
• DO NOT apply to wheat, barley, oats, and triticale underseeded with another crop.
• DO NOT harvest wheat or barley sooner than 45 days after the last application of AFFINITY BroadSpec 
herbicide.
• DO NOT apply, drain or flush equipment on or near desirable trees or other plants or on areas where their roots 
may extend, or in locations where the chemical may be washed or moved into contact with their roots.
• DO NOT use on lawns, walks, driveways, or tennis courts. 
• DO NOT apply this product through any type of irrigation system.
• DO NOT apply AFFINITY BroadSpec herbicide by air in the state of New York.
PRECAUTIONS
Injury to or loss of adjacent sensitive crops, desirable trees or vegetation may result from failure to observe the 
following:
• Take all necessary precautions to avoid all direct or indirect contact (including spray drift) with non-target plants 
or areas.
Carefully observe all sprayer cleanup instructions both prior to and after using this product, as spray tank residue 
may damage crops other than wheat, barley, oats, and triticale.
Dry, dusty field conditions may result in reduced control in wheel track areas.

4 
 
AFFINITY BroadSpec herbicide must not be applied to wheat, barley, oats, and triticale that is stressed by severe 
weather conditions, drought (including low levels of subsoil moisture), low fertility, water-saturated soil, disease, or 
insect damage, as crop injury may result. Risk of injury is greatest when crop is in the 2 to 5- leaf stage. Severe 
winter stress, drought, disease, or insect damage following application also may result in crop injury.
Wheat, barley, oats, and triticale may differ in their response to various herbicides. FMC advises that you first 
consult your state experiment station, university, or extension agent as to sensitivity to any herbicide. If no 
information is available, limit the initial use of AFFINITY BroadSpec herbicide to a small area.
Under certain conditions, including heavy rainfall, prolonged cold weather (daily high temperature less than 50o F), 
or wide fluctuations in day/night temperatures prior to or soon after AFFINITY BroadSpec herbicide application, 
temporary discoloration and/or crop injury may occur. To reduce the potential of crop injury, tank mix AFFINITY 
BroadSpec herbicide with 2,4-D (ester formulations perform best–see “Tank Mixtures” section of this label) and 
apply after the crop is in the tillering stage of growth.
It is the pesticide user’s responsibility to ensure that all products are registered for the intended use. Read and follow 
the applicable restrictions and limitations and directions for use on all product labels involved in tank mixing. Users 
must follow the most restrictive directions for use and precautionary statements of each product in the tank 
mixture.). 
ENVIRONMENTAL CONDITIONS AND BIOLOGICAL ACTIVITY
AFFINITY BroadSpec herbicide is absorbed primarily through the foliage of plants, rapidly inhibiting the growth of 
susceptible weeds. One to 3 weeks after application to weeds, leaves of susceptible plants appear chlorotic, and the 
growing point subsequently dies.
AFFINITY BroadSpec herbicide provides the best control in vigorously growing crops that shade competitive 
weeds. Weed control in areas of thin crop stand or seeding skips may not be as satisfactory. However, a crop canopy 
that is too dense at application can intercept spray and reduce weed control.
The herbicidal action of AFFINITY BroadSpec herbicide may be affected in crops stressed from adverse 
environmental conditions (including extreme temperatures or moisture), abnormal soil conditions, cultural practices, 
or variations in crop variety. In warm, moist conditions, the expression of herbicide symptoms is accelerated; in 
cold, dry conditions, expression of herbicide symptoms is delayed. In addition, weeds hardened-off by drought stress 
are less susceptible to AFFINITY BroadSpec herbicide.
WEED RESISTANCE MANAGEMENT
AFFINITY BroadSpec herbicide, which contains the active ingredients Thifensulfuron methyl and Tribenuron 
methyl, is a group 2 herbicide based on the mode of action classification system of the Weed Science Society of 
America.
Proactively implementing diversified weed control strategies to minimize selection for weed populations resistant to 
one or more herbicides is a best practice. A diversified weed management program may include the use of multiple 
herbicides with different sites of action and overlapping weed spectrum with or without tillage operations and/or 
other cultural practices.
Research has demonstrated that using the labeled rate and directions for use is important to delay the selection for 
resistance.
The continued effectiveness of this product depends on the successful implementation of a weed resistance 
management program.
To aid in the prevention of developing weeds resistant to this product, users should:
• Scout fields before application to ensure herbicides and rates will be appropriate for the weed species and weed 
sizes present.
• Start with a clean field, using either a burndown herbicide application or tillage.
• Control weeds early when they are relatively small (less than 4 inches).
• Apply full rates of AFFINITY BroadSpec herbicide for the most difficult to control weed in the field at the 
specified time (correct weed size) to minimize weed escapes.
• Scout fields after application to detect weed escapes or shifts in control of weed species.

5 
 
• Control weed escapes before they reproduce by seed or proliferate vegetatively.
• Report any incidence of non-performance of this product against a particular weed to your FMC representative, 
local retailer, or county extension agent.
• Contact your FMC representative, crop advisor, or extension agent to find out if suspected resistant weeds to these 
MOAs have been found in your region. DO NOT assume that each listed weed is being controlled by multiple sites 
of action. Products with multiple active ingredients are intended to broaden the spectrum of weeds that are 
controlled. Some weeds may be controlled by only one of the active ingredient in this product.
• If resistance is suspected, treat weed escapes with an herbicide having a site of action other than Group 2 and/or 
use nonchemical methods to remove escapes, as practical, with the goal of preventing further seed production.
• Suspected herbicide-resistant weeds may be identified by these indicators:
- Failure to control a weed species normally controlled by the herbicide at the dose applied, especially if 
control is achieved on adjacent weeds;
- A spreading patch of non-controlled plants of a particular weed species; and
- Surviving plants mixed with controlled individuals of the same species.
Additionally, users should follow as many of the following herbicide resistance management practices as is 
practical:
• Use a broad spectrum soil-applied herbicide with other sites of action as a foundation in a weed control program.
• Utilize sequential applications of herbicides with alternative sites of action.
• Rotate the use of this product with non-Group 2 herbicides.
• Avoid making more than two applications of AFFINITY BroadSpec herbicide and any other Group 2 herbicides 
within a single growing season unless mixed with an herbicide with a different site of action with an overlapping 
spectrum for the difficult-to-control weeds.
• Incorporate non-chemical weed control practices, including mechanical cultivation, crop rotation, cover crops and 
weed-free crop seeds, as part of an integrated weed control program.
• Use good agronomic principles that enhance crop development and crop competitiveness.
• Thoroughly clean plant residues from equipment before leaving fields suspected to contain resistant weeds.
• Manage weeds in and around fields, during and after harvest to reduce weed seed production.
INTEGRATED PEST MANAGEMENT
FMC advises the use of Integrated Pest Management (IPM) programs to control pests. This product may be used as 
part of an Integrated Pest Management (IPM) program that can include biological, cultural, and genetic practices 
aimed at preventing economic pest damage. Base the application of this product on IPM principles and practices 
including field scouting or other detection methods, correct target pest identification, population monitoring, and 
treating when target pest populations reach locally determined action thresholds. Consult your state cooperative 
extension service, professional consultants or other qualified authorities to determine appropriate action treatment 
threshold levels for treating specific pest/crop systems in your area.

6 
 
RATE CONVERSION CHART FOR AFFINITY BROADSPEC HERBICIDE
Ounces of 
AFFINITY BroadSpec 
herbicide/A
Pounds of 
AFFINITY BroadSpec
herbicide /A Active Ingredient
Pounds of Active 
Ingredient/A
0.4 0.025
Thifensulfuron methyl 0.0063
Tribenuron methyl 0.0063
0.5 0.0313
Thifensulfuron methyl 0.0078
Tribenuron methyl 0.0078
0.6 0.0375
Thifensulfuron methyl 0.0094
Tribenuron methyl 0.0094
0.8 0.05
Thifensulfuron methyl 0.0125
Tribenuron methyl 0.0125
1.0 0.0625
Thifensulfuron methyl 0.0156
Tribenuron methyl 0.0156

7 
 
LABELLED USES
AFFINITY BroadSpec herbicide provides selective postemergence control of certain broadleaf weeds in wheat 
(including durum), barley, oat (spring and winter), triticale, post-harvest burndown, pre-plant burndown and fallow.
Wheat (Including Durum), Barley, and Triticale
Application and Use Rate Information
Use Rates (oz of 
AFFINITY 
BroadSpec
herbicide per acre)
Active 
Ingredient
Pounds of Active 
Ingredient per acre
Make applications after the crop is in the 2-
leaf stage, but before the flag leaf is visible.
Apply 0.4 to 1.0 oz AFFINITY BroadSpec 
herbicide per acre.
Sequential treatments of AFFINITY 
BroadSpec herbicide may be made provided 
the total amount of AFFINITY BroadSpec 
herbicide applied to the crop per year does
not exceed 1.0 oz/A. 
0.4 to 1.0
Thifensulfuron 
methyl
0.0063 to 0.0156
Tribenuron 
methyl
0.0063 to 0.0156
RESTRICTIONS in Wheat (including durum), Barley, and Triticale:
x DO NOT apply to wheat, barley, or triticale crops underseeded with another crop.
x DO NOT harvest wheat or barley sooner than 45 days after the last application of AFFINITY BroadSpec 
herbicide.
x DO NOT apply more than 1.0 oz of AFFINITY BroadSpec herbicide p er acre in a single application 
(maximum active ingredient per single application is 0.0156 lb/A thifensulfuron methyl and 0.0156 lb/A 
tribenuron methyl).
x DO NOT exceed two applications of AFFINITY BroadSpec herbicide per year in Wheat (including 
durum), Barley and Triticale when using reduced application rates.
x DO NOT apply more than 1.0 oz of AFFINITY BroadSpec herbicide p er acre per year (maximum active 
ingredient load per year is 0.0156 lb/A thifensulfuron methyl and 0.0156 lb/A tribenuron methyl).
x When applying 0.4 to 0.6 oz per acre, AFFINITY BroadSpec herbicide must be used in a tank-mix 
combination with other registered herbicides.
x The Minimum Retreatment Interval is 14 days.
x PHI is 7 days for forage, 30 days for hay, and 45 days for wheat, barley and triticale.
PRECAUTIONS in Wheat (including durum), Barley, and Triticale:
Carefully observe all sprayer cleanup instructions both prior to and after using this product, as spray tank residue 
may damage crops other than wheat, barley, and triticale.
AFFINITY BroadSpec herbicide must not be applied to wheat, barley, and triticale that is stressed by severe weather 
conditions, drought (including low levels of subsoil moisture), low fertility, water-saturated soil, disease, or insect 
damage, as crop injury may result. Risk of injury is greatest when crop is in the 2 to 5- leaf stage. Severe winter 
stress, drought, disease, or insect damage following application also may result in crop injury.
Wheat, barley, and triticale may differ in their response to various herbicides. FMC suggests that you first consult 
your state experiment station, university, or extension agent as to sensitivity to any herbicide. If no information is 
available, limit the initial use of AFFINITY BroadSpec herbicide to a small area.
TANK MIXTURES in Wheat (including durum), Barley, and Triticale:
For expanded weed control, AFFINITY BroadSpec herbicide may be tank mixed with approved labeled rates of 
other herbicides labeled for use in wheat (including durum), barley and triticale. Refer to the other product’s label

8 
 
for rotational crop intervals and other directions for use. When applying 0.4 to 0.6 oz/A in wheat, barley and 
triticale, AFFINITY BroadSpec herbicide must be used in a tank-mix combination with other registered herbicides.
It is the pesticide user’s responsibility to ensure that all products are registered for the intended use. Read and 
follow the applicable restrictions, limitations and directions for use on all product labels involved in tank mixing. 
Users must follow the most restrictive directions for use and precautionary statements of each product in the tank 
mixture. If the instructions on the tank mix partner label conflict with this AFFINITY BroadSpec herbicide, then 
DO NOT use in a tank mixture with AFFINITY BroadSpec herbicide.
Winter Oat
Application and Use Rate Information
Use Rates (oz of 
AFFINITY 
BroadSpec
herbicide per acre)
Active 
Ingredient
Pounds of Active 
Ingredient per acre
Make applications after the crop is in the 2-
leaf stage, but before the flag leaf is visible.
Apply 0.4 oz/A AFFINITY BroadSpec 
herbicide for control of light populations of 
the weeds listed in Weeds Controlled table. 
In oat, AFFINITY BroadSpec herbicide 
must be used in a tank-mix combination with 
other registered herbicides.
0.4
Thifensulfuron 
methyl
0.0063
Tribenuron 
methyl
0.0063
RESTRICTIONS in Winter Oat:
x DO NOT apply to oat crops underseeded with another crop.
x DO NOT apply more than 0.4 oz/A of AFFINITY BroadSpec herbicide in a single application 
(maximum active ingredient per single application is 0.0063 lb/A thifensulfuron methyl and 0.0063 lb/A 
tribenuron methyl). 
x DO NOT apply more than 0.4 oz/A of AFFINITY BroadSpec herbicide per year (maximum active 
ingredient load per year is 0.0063 lb/A thifensulfuron methyl and 0.0063 lb/A tribenuron methyl) in 
Winter Oat. 
x DO NOT make more than one application (or more than 0.0063 lb/A of active ingredient tribenuron-
methyl) of AFFINITY BroadSpec herbicide per year on Winter Oat.
x The REI is 12 hours.
PRECAUTIONS in Winter Oat:
Carefully observe all sprayer cleanup instructions both prior to and after using this product, as spray tank residue 
may damage crops other than oat.
AFFINITY BroadSpec herbicide must not be applied to oat that is stressed by severe weather conditions, drought 
(including low levels of subsoil moisture), low fertility, water-saturated soil, disease, or insect damage, as crop 
injury may result.
Risk of injury is greatest when crop is in the 2 to 5-leaf stage. Severe winter stress, drought, disease, or insect 
damage following application also may result in crop injury.
Oat may differ in their response to various herbicides. FMC suggests that you first consult your state experiment 
station, university, or extension agent as to sensitivity to any herbicide. If no information is available, limit the initial 
use of AFFINITY BroadSpec herbicide to a small area.

9 
 
TANK MIXTURES in Winter Oat:
For expanded weed control, AFFINITY BroadSpec herbicide must be tank mixed with approved labeled rates of 
other herbicides labeled for use in winter oat. Refer to the other product’s label for rotational crop intervals and 
other directions for use.
It is the pesticide user’s responsibility to ensure that all products are registered for the intended use. Read and 
follow the applicable restrictions, limitations and directions for use on all product labels involved in tank mixing. 
Users must follow the most restrictive directions for use and precautionary statements of each product in the tank 
mixture. If the instructions on the tank mix partner label conflict with this AFFINITY BroadSpec herbicide, then 
DO NOT use in a tank mixture with AFFINITY BroadSpec herbicide.
Spring Oat
Application and Use Rate Information
Use Rates (oz of 
AFFINITY 
BroadSpec
herbicide per acre)
Active 
Ingredient
Pounds of Active 
Ingredient per acre
Make applications after the crop is in the 3-
leaf stage but before jointing. 
Apply 0.4 oz/A AFFINITY BroadSpec 
herbicide for control of light populations of 
the weeds listed in Weeds Controlled table. 
In oat, AFFINITY BroadSpec herbicide 
must be used in a tank-mix combination with 
other registered herbicides.
0.4
Thifensulfuron 
methyl 0.0063
Tribenuron 
methyl 0.0063
RESTRICTIONS in Spring Oat:
x DO NOT apply to oat crops underseeded with another crop.
x DO NOT apply more than 0.4 oz/A of AFFINITY BroadSpec herbicide in a single application 
(maximum active ingredient per single application is 0.0063 lb/A thifensulfuron methyl and 0.0063 lb/A 
tribenuron methyl). 
x DO NOT apply more than 0.4 oz/A of AFFINITY BroadSpec herbicide per year (maximum active 
ingredient load per year is 0.0063 lb/A thifensulfuron methyl and 0.0063 lb/A tribenuron methyl) in 
Spring Oat. 
x DO NOT make more than one application (or more than 0.0063 lb/A of active ingredient tribenuron-
methyl) of AFFINITY BroadSpec herbicide per year on Spring Oat.
x The REI is 12 hours.
x DO NOT use on "Ogle", "Porter" or "Premier" varieties as crop injury can occur.
PRECAUTIONS in Spring Oat:
Carefully observe all sprayer cleanup instructions both prior to and after using this product, as spray tank residue 
may damage crops other than oat.
AFFINITY BroadSpec herbicide must not be applied to oat that is stressed by severe weather conditions, drought 
(including low levels of subsoil moisture), low fertility, water-saturated soil, disease, or insect damage, as crop 
injury may result. Risk of injury is greatest when crop is in the 2 to 5-leaf stage. Severe winter stress, drought, 
disease, or insect damage following application also may result in crop injury.
Oat may differ in their response to various herbicides. FMC suggests that you first consult your state experiment 
station, university, or extension agent as to sensitivity to any herbicide. If no information is available, limit the initial
use of AFFINITY BroadSpec herbicide to a small area.

10 
 
TANK MIXTURES in Spring Oat:
For expanded weed control, AFFINITY BroadSpec herbicide must be tank mixed with approved labeled rates of 
other herbicides labeled for use in spring oat. Refer to the other product’s label for rotational crop intervals and other 
directions for use.
It is the pesticide user’s responsibility to ensure that all products are registered for the intended use. Read and 
follow the applicable restrictions, limitations and directions for use on all product labels involved in tank mixing. 
Users must follow the most restrictive directions for use and precautionary statements of each product in the tank 
mixture. If the instructions on the tank mix partner label conflict with this AFFINITY BroadSpec herbicide, then 
DO NOT use in a tank mixture with AFFINITY BroadSpec herbicide.
Pre-Plant Burndown
Application and Use Rate Information
Use Rates (oz 
of AFFINITY 
BroadSpec
herbicide per 
acre)
Active 
Ingredient
Pounds of 
Active 
Ingredient per 
acre
Apply AFFINITY BroadSpec herbicide as a burndown 
treatment to wheat (including durum) and barley to 
control emerged weeds prior to, or shortly after planting 
(prior to emergence). Make applications when the 
majority of weeds have emerged and are actively 
growing.
AFFINITY BroadSpec herbicide can be used as a 
burndown treatment prior to planting other crops. See 
"CROP ROTATION" for the time interval required 
before planting.
Apply 0.4 to 1.0 oz/A AFFINITY BroadSpec herbicide 
as a burndown treatment prior to, or shortly after planting 
(prior to emergence).
When applying 0.4 to 0.6 oz/A, AFFINITY BroadSpec 
herbicide must be used in a tank-mix combination with 
other registered herbicides.
Sequential treatments of AFFINITY BroadSpec herbicide 
may also be made provided the total amount of
AFFINITY BroadSpec herbicide applied during one year 
does not exceed 1.0 oz/A.
0.4 to 1.0
Thifensulfuron 
methyl
0.0063 to 0.0156
Tribenuron 
methyl
0.0063 to 0.0156
RESTRICTIONS for Pre-Plant Burndown (Wheat including durum, Barley, and other crops):
x DO NOT use less than 0.4 oz/A AFFINITY BroadSpec herbicide, unless otherwise specified by FMC.
x DO NOT apply more than 1.0 oz/A of AFFINITY BroadSpec herbicide in a single application 
(maximum active ingredient per single application is 0.0156 lb/A thifensulfuron methyl and 0.0156 lb/A 
tribenuron methyl).
x DO NOT apply more than 1.0 oz/A of AFFINITY BroadSpec herbicide per year (maximum active 
ingredient load per year is 0.0156 lb/A thifensulfuron methyl and 0.0156 lb/A tribenuron methyl).
x DO NOT exceed two applications of AFFINITY BroadSpec herbicide per year for Pre-Plant Burndown 
(Wheat including durum, Barley, and other crops) when using reduced application rates.
x The Minimum Retreatment Interval is 14 days.

11 
 
TANK MIXTURES for Pre-Plant Burndown:
AFFINITY BroadSpec herbicide may be used as a pre-plant burndown treatment alone or tank mixed with approved 
labeled rates of other herbicides labeled for use as a pre-plant burndown product. Refer to the other product’s label 
for rotational crop intervals and other directions for use. When applying 0.4 to 0.6 oz/A as a pre-plant burndown 
treatment, AFFINITY BroadSpec herbicide must be used in a tank-mix combination with other registered 
herbicides.
It is the pesticide user’s responsibility to ensure that all products are registered for the intended use. Read and 
follow the applicable restrictions, limitations and directions for use on all product labels involved in tank mixing. 
Users must follow the most restrictive directions for use and precautionary statements of each product in the tank 
mixture. If the instructions on the tank mix partner label conflict with this AFFINITY BroadSpec herbicide, then 
DO NOT use in a tank mixture with AFFINITY BroadSpec herbicide.
Post-Harvest Burndown
Application and Use Rate Information
Use Rates (oz of 
AFFINITY 
BroadSpec
herbicide per 
acre)
Active 
Ingredient
Pounds of Active 
Ingredient per acre
AFFINITY BroadSpec herbicide may be used as a 
burndown treatment to crop stubble when the 
majority of weeds have emerged and are actively 
growing. (See the “CROP ROTATION” section of 
this label for additional information).
Apply AFFINITY BroadSpec herbicide at 0.4 to 
1.0 oz/A to crop stubble after harvest. Use the 1.0 
oz/A rate when weed infestation is heavy and 
predominantly consists of those weeds listed under 
the “WEEDS PARTIALLY CONTROLLED” 
section of this label or when application timing 
and environmental conditions are marginal. Apply 
AFFINITY BroadSpec herbicide in combination 
with other suitable registered burndown 
herbicides.
Sequential treatments of AFFINITY BroadSpec 
herbicide may also be made provided the total 
amount of AFFINITY BroadSpec herbicide 
applied in one year does not exceed 1.0 oz/A.
0.4 to 1.0
Thifensulfuron 
methyl
0.0063 to 0.0156
Tribenuron 
methyl
0.0063 to 0.0156
RESTRICTIONS for Post-Harvest:
x DO NOT use less than 0.4 oz/A AFFINITY BroadSpec herbicide, unless otherwise specified by FMC.
x DO NOT apply more than 1.0 oz/A of AFFINITY BroadSpec herbicide in a single application 
(maximum active ingredient per single application is 0.0156 lb/A thifensulfuron methyl and 0.0156 lb/A 
tribenuron methyl).
x DO NOT apply more than 1.0 oz/A AFFINITY BroadSpec herbicide pe r year (maximum active 
ingredient load per year is 0.0156 lb/A thifensulfuron methyl and 0.0156 lb/A tribenuron methyl).
x DO NOT exceed two applications of AFFINITY BroadSpec herbicide per year for Post-Harvest 
Burndown when using reduced application rates.
x The Minimum Retreatment Interval is 14 days.

12 
 
TANK MIXTURES for Post-Harvest Burndown:
AFFINITY BroadSpec herbicide may be used as a post-harvest treatment to crop stubble and must be tank mixed 
with approved labeled rates of other herbicides labeled for use as a post-harvest burndown treatment. Refer to the 
other product’s label for rotational crop intervals and other directions for use. 
It is the pesticide user’s responsibility to ensure that all products are registered for the intended use. Read and 
follow the applicable restrictions, limitations and directions for use on all product labels involved in tank mixing. 
Users must follow the most restrictive directions for use and precautionary statements of each product in the tank 
mixture. If the instructions on the tank mix partner label conflict with this AFFINITY BroadSpec herbicide, then 
DO NOT use in a tank mixture with AFFINITY BroadSpec herbicide.
Fallow
Application and Use Rate Information
Use Rates (oz of 
AFFINITY 
BroadSpec
herbicide per acre)
Active 
Ingredient
Pounds of Active 
Ingredient per acre
AFFINITY BroadSpec herbicide may be 
used as a fallow treatment, in the spring, 
summer or fall when the majority of weeds 
have emerged and are actively growing.
Apply 0.4 to 1.0 oz/A AFFINITY BroadSpec 
herbicide to fallow. The total amount of 
AFFINITY BroadSpec herbicide cannot 
exceed 1.0 oz/A per year.
When AFFINITY BroadSpec herbicide is 
applied at a rate of 0.4 to 0.6 oz/A, 
AFFINITY BroadSpec herbicide must be 
used in a tank-mix combination with other 
registered fallow herbicides. In fallow, 
AFFINITY BroadSpec herbicide may be 
applied in combination with other suitable 
registered fallow herbicides including 
glyphosate plus 2,4-D (ester formulations 
work best) or glyphosate plus dicamba.
0.4 to 1.0
Thifensulfuron
methyl
0.0063 to 0.0156
Tribenuron 
methyl
0.0063 to 0.0156
RESTRICTIONS in Fallow:
x DO NOT use less than 0.4 oz/A AFFINITY BroadSpec herbicide, unless otherwise specified by FMC.
x DO NOT apply more than 1.0 oz/A AFFINITY BroadSpec herbicide in a single application (maximum 
active ingredient per single application is 0.0156 lb/A thifensulfuron methyl and 0.0156 lb/A tribenuron 
methyl).
x DO NOT apply more than 1.0 oz /A AFFINITY BroadSpec herbicide pe r year (maximum active 
ingredient load per year is 0.0156 lb/A thifensulfuron methyl and 0.0156 lb/A tribenuron methyl).
x DO NOT exceed two applications of AFFINITY BroadSpec herbicide per year in Fallow when using 
reduced application rates.
x The Minimum Retreatment Interval is 14 days.

13 
 
TANK MIXTURES in Fallow:
AFFINITY BroadSpec herbicide may be used as a fallow treatment and must be tank mixed with approved labeled 
rates of other herbicides labeled for use in fallow. Refer to the other product’s label for rotational crop intervals and 
other directions for use.
It is the pesticide user’s responsibility to ensure that all products are registered for the intended use. Read and 
follow the applicable restrictions, limitations and directions for use on all product labels involved in tank mixing. 
Users must follow the most restrictive directions for use and precautionary statements of each product in the tank 
mixture. If the instructions on the tank mix partner label conflict with this AFFINITY BroadSpec herbicide, then 
DO NOT use in a tank mixture with AFFINITY BroadSpec herbicide.
TANK MIXTURES
It is the pesticide user’s responsibility to ensure that all products are registered for the intended use. Read and 
follow the applicable restrictions, limitations and directions for use on all product labels involved in tank mixing. 
Users must follow the most restrictive directions for use and precautionary statements of each product in the tank 
mixture. If the instructions on the tank mix partner label conflict with this AFFINITY BroadSpec herbicide, then 
DO NOT use in a tank mixture with AFFINITY BroadSpec herbicide.
AFFINITY BroadSpec herbicide may be tank mixed with one or more suitable registered herbicides to control 
weeds listed as suppressed, weeds resistant to AFFINITY BroadSpec herbicide or weeds not listed under Weeds 
Controlled. Read and follow all manufacturer’s label instructions for the companion herbicide. If those instructions 
conflict with this label, DO NOT tank mix the herbicide with AFFINITY BroadSpec herbicide.
AFFINITY BroadSpec herbicide can also be mixed with registered fungicides, insecticides, or liquid fertilizer for 
use on wheat, barley, or fallow.
With Other Grass Control Products
AFFINITY BroadSpec herbicide can be tank mixed with grass control products. Antagonism generally does not 
occur. Under certain environmental conditions, however, antagonism to Group 1 graminicides can occur. This may 
be reduced by using the higher rate of the graminicide. FMC advises that you first consult your state experiment 
station, university, or extension agent, Agricultural dealer, or FMC representative as to the potential for antagonism 
before using the mixture. If no information is available, limit the initial use of AFFINITY BroadSpec herbicide and 
the grass product to a small area.
With Insecticides or Fungicides
AFFINITY BroadSpec herbicide may be tank mixed or used sequentially with insecticides (or fungicides) registered 
for use on cereal grains. However, under certain conditions (drought stress, or if the crop is in the 2-4 leaf stage), 
tank mixes or sequential applications of AFFINITY BroadSpec herbicide with organophosphate insecticides 
(including parathion) may produce temporary crop yellowing or, in severe cases, crop injury. Test these mixtures in 
a small area before treating large areas. However, review all insecticide and fungicide labels for restrictions.
DO NOT use AFFINITY BroadSpec herbicide plus products containing malathion, as crop injury will result.
With Liquid Nitrogen Solution Fertilizer
Liquid nitrogen fertilizer solutions may be used as a carrier in place of water. Run a tank mix compatibility test 
before mixing AFFINITY BroadSpec herbicide in fertilizer solution. DO NOT add AFFINITY BroadSpec herbicide 
directly to liquid nitrogen fertilizer; the granules will not dissolve. AFFINITY BroadSpec herbicide must be 
thoroughly mixed with clean water before it is added to liquid nitrogen fertilizer. If granules remain when the 
mixture is poured out, add more clean water and mix until all granules have disappeared. Ensure that the agitator is 
running when the AFFINITY BroadSpec herbicide premix is added. Use of this mixture may result in temporary 
crop yellowing and stunting.
If using low rates of liquid nitrogen fertilizer in the spray solution (less than 50% of the spray solution volume), the 
addition of surfactant is necessary. Add surfactant at 1/4 qt - 1 qt per 100 gal of spray solution (0.06 -0.25% v/v) 
based on local guidance.

14 
 
When using high rates of liquid nitrogen fertilizer solution in the spray solution, adding surfactant increases the risk 
of crop injury. Consult your agricultural dealer, consultant, fieldman, or FMC representative for specific instructions 
before adding an adjuvant to these tank mixtures.
If 2,4-D or MCPA is included with AFFINITY BroadSpec herbicide and fertilizer mixture, ester formulations tend 
to be more compatible (see manufacturer’s label). Additional surfactant is not needed when using AFFINITY 
BroadSpec herbicide in tank mix with 2,4-D ester or MCPA ester and liquid nitrogen fertilizer solutions.
DO NOT use low rates of liquid nitrogen fertilizer solution as a substitute for a surfactant.
DO NOT use with liquid fertilizer solutions with a pH less than 3.0.
CROP ROTATION
Labeled crops may be planted at specified time intervals following application of labeled rates of AFFINITY 
BroadSpec herbicide. Use the time intervals listed below to determine the required time interval before planting.
Refer to individual product labels to determine rotational crop restrictions when tank mixtures are used.
Time Interval Before Planting* (days after treatment with AFFINITY BroadSpec herbicide)
Crop Days
Barley, Rice, Soybeans with Bolt® technology, Triticale, and Wheat (including durum) 0
Soybeans 7†*
Cotton, Field Corn, and Grain Sorghum 14*
Sugarbeets, Winter Rape, and Canola 60
Any other crop 45
† When AFFINITY BroadSpec is applied at 0.5 oz/a or less the time interval for soybeans is 1 day.
* Where AFFINITY BroadSpec is used on light textured soils, including sands and loamy sands, extend time to 
planting by 7 additional days. Where AFFINITY BroadSpec is used on high pH soils (>7.9), extend time to 
planting by 7 additional days.

15 
 
WEEDS CONTROLLED
AFFINITY BroadSpec herbicide effectively controls the following weeds when used according to label directions:
Annual knawel
Annual sowthistle
Black mustard
Blue/Purple mustard
Broadleaf dock
Bur buttercup
Bushy wallflower/Treacle mustard
Canada thistle *
Clasping pepperweed
Coast fiddleneck
Common buckwheat
Common chickweed
Common cocklebur *
Common groundsel
Common lambsquarters
Common ragweed *
Common sunflower
Corn chamomile
Corn gromwell *
Corn spurry
Cowcockle
Cress (mouse-ear)
Curly dock
False chamomile
Field chickweed
Field pennycress
Filaree (redstem, Texas)
Flixweed
Green smartweed
Henbit
Kochia *
Ladysthumb
Lanceleaf sage *
London rocket
Marshelder
Mayweed chamomile
Miners lettuce
Narrrowleaf lambsquarters
Nightflowering catchfly
Pennsylvania smartweed
Pineappleweed
Prickly lettuce*
Prostrate knotweed
Prostrate pigweed
Redmaids
Redroot pigweed
Russian thistle*
Scentless chamomile/mayweed
Shepherd's-purse
Slimleaf lambsquarters
Smallflower buttercup
Smallseed falseflax
Stinking chickweed
Stinking mayweed/dogfennel
Sunflower
Swinecress
Tansymustard
Tarweed fiddleneck
Tumble/Jim Hill mustard
Volunteer canola
Volunteer lentils
Volunteer peas
White cockle
Wild buckwheat*
Wild chamomile
Wild mustard
WEEDS PARTIALLY CONTROLLED**
AFFINITY BroadSpec herbicide partially controls the following weeds when used according to label directions:
Catchweed bedstraw Marestail
Mallow (common, little) Nightshade (cutleaf, hairy)
* See SPECIFIC WEED PROBLEMS for more information.
**Partial control: A visual reduction of weed population as well as a significant loss of vigor. For better results, use the highest specified rate of 
AFFINITY BroadSpec herbicide per acre and include a tank mix partner including 2,4-D, MCPA, bromoxynil containing herbicides or
dicamba containing herbicides.

16 
 
SPECIFIC WEED PROBLEMS
Canada thistle: For control in wheat and barley, use 0.8 oz/A AFFINITY BroadSpec herbicide plus surfactant 
when all thistles are 4" to 8" with 2" to 6" of new growth. Make the application in the spring. Control will be 
improved by using AFFINITY BroadSpec herbicide in combination with 2,4-D, dicamba, WideMatch® herbicide, 
or Colt® AS herbicide. 
Common cocklebur, Common ragweed, Lanceleaf sage: In wheat and barley, apply AFFINITY BroadSpec 
herbicide at 0.4 to 0.8 oz/A in combination with 2,4-D at rates from 1/4 to 3/8 lb active ingredient (ester 
formulations work best) when weeds are small and actively growing. When using 1/4 lb active ingredient of 2,4-D, 
be sure to add surfactant at the rate of 1/4 to 1/2 quart per 100 gallons of spray solution (0.06 to 0.125% v/v--use the 
higher rate under stress conditions).
Corn gromwell, Wild buckwheat: For control in wheat and barley, use 0.8 oz/A AFFINITY BroadSpec herbicide 
plus surfactant.
Kochia, Russian thistle, Prickly lettuce: Naturally occurring resistant biotypes of these weeds are known to occur. 
For best results, use AFFINITY BroadSpec herbicide in a tank mix with Colt + Sword® herbicide, Colt + Salvo® 
herbicide, dicamba and 2,4-D; or Bromoxynil (including Buctril® herbicide) and 2,4-D (3/4 - 1 pt Buctril herbicide 
+ 1/4 - 3/8 lb active ingredient 2, 4-D ester). For improved broadleaf weed control including kochia, AFFINITY 
BroadSpec herbicide can also be tank mixed with WideMatch® herbicide, Colt® AS herbicide or Starane® NXT 
herbicide. AFFINITY BroadSpec herbicide must be applied in the spring when weeds are 2” to 4" tall or 2” to 4" 
across and are actively growing. Refer to the Tank Mixtures section of this label for additional details.
Yellow and Green Foxtail: AFFINITY BroadSpec herbicide at 0.6 - 1.0 oz/A may be tank mixed with GoldSky®
herbicide, “Everest®” branded products, or Rimfire® Max herbicide for yellow and green foxtail suppression in 
wheat.
SPRAY ADJUVANTS
Always include a spray adjuvant with applications of AFFINITY BroadSpec herbicide. In addition to a spray 
adjuvant, an ammonium nitrogen fertilizer may be used.
Consult your Ag dealer or applicator, local FMC fact sheets, technical bulletins, and service policies prior to using 
an adjuvant system. If another herbicide is tank mixed with AFFINITY BroadSpec herbicide, select adjuvants 
authorized for use with both products. Products must contain only EPA-exempt ingredients (40CFR 1001).
Nonionic Surfactant (NIS)
• Apply 0.06 to 0.50% volume/volume (1/2 pt to 4 pt per 100 gal of spray solution).
• Surfactant products must contain at least 60% nonionic surfactant with a hydrophilic/lipophilic balance (HLB) 
greater than 12. See the Tank Mixtures section of this label for additional information.
Petroleum Crop Oil Concentrate (COC) or Modified Seed Oil (MSO)
• Apply at 1% volume/volume (1 gal per 100 gal spray solution) or 2% volume/volume under arid conditions.
• Oil adjuvants must contain at least 80% high quality, petroleum (mineral) or modified vegetable seed oil with at 
least 15% surfactant emulsifiers.
Special Adjuvant Types
• Combination adjuvant products may be used at doses that provide the required amount of NIS, COC, MSO and/or
ammonium nitrogen fertilizer. Consult product literature for use rates and restrictions.
• In addition to the adjuvants specified above, other adjuvant types may be used if they provide the same 
functionality and have been evaluated and approved by FMC product management. 
Ammonium Nitrogen Fertilizer
• Use 2 qt/acre of a high-quality urea ammonium nitrate (UAN), including 28%N or 32%N, or 2 lb/acre of a spray-
grade ammonium sulfate (AMS). Use 4 qt/acre UAN or 4 lb/acre AMS under arid conditions.
APPLICATION TIMING
Since AFFINITY BroadSpec herbicide has very little or no soil activity, it controls only those weeds that have 
germinated; therefore, apply AFFINITY BroadSpec herbicide when all or most of the weeds have germinated. 
Annual broadleaf weeds must be past the cotyledon stage, actively growing, and less than 4" tall or wide. Rainfall

17 
 
immediately after treatment can wash AFFINITY BroadSpec herbicide off of weed foliage, resulting in reduced 
weed control. Several hours of dry weather are needed to allow AFFINITY BroadSpec herbicide to be sufficiently
absorbed by weed foliage.
GROUND APPLICATION
For optimum spray distribution and thorough coverage, use flat-fan or low-volume flood nozzles.
For flat-fan nozzles, use a spray volume of at least 5 gal per acre (GPA).
For flood nozzles on 30” spacings, use at least 10 GPA, flood nozzles no larger than TK10 (or the equivalent), and a 
pressure of at least 30 psi. For 40” nozzle spacings, use at least 13 GPA; for 60” spacings use at least 20 GPA. It is 
essential to overlap the nozzles 100% for all spacings.
Raindrop “RA” nozzles are not advised for AFFINITY BroadSpec herbicide applications, as weed control 
performance may be reduced.
Use screens that are 50-mesh or larger.
AERIAL APPLICATION
Use nozzle types and arrangements that provide optimum spray distribution and maximum coverage at 2 to 5 GPA. 
Use at least 3 GPA in Idaho, Oregon, or Utah. 
This product is limited to ground application only in the State of New York.
See the Spray Drift section of this label.
CHEMIGATION
DO NOT apply this product through any irrigation system.
PRODUCT MEASUREMENT
AFFINITY BroadSpec herbicide is measured using the AFFINITY Broa dSpec herbicide volumetric measuring 
cylinder. The degree of accuracy of this cylinder varies by + 7.5%. For more precise measurement, use scales 
calibrated in ounces.
PESTICIDE HANDLING
• Calibrate sprayers only with clean water away from the well site.
• Make scheduled checks of spray equipment.
• Ensure that all operation employees accurately measure pesticides.
• Mix only enough product for the job at hand.
• Avoid overfilling of spray tank.
• DO NOT discharge excess material on the soil at a single spot in the field, grove, or mixing/loading station.
• Dilute and agitate excess solution and apply at labeled rates or uses.
• Avoid storage of pesticides near well sites.
• When triple-rinsing the pesticide container, be sure to add the rinsate to the spray mix.
MIXING INSTRUCTIONS
DO NOT use with spray additives that alter the pH of the spray solution below pH 5.0 or above pH 9.0 as rapid 
product degradation can occur. Spray solutions of pH 6.0-8.0 allow for optimum stability of AFFINITY BroadSpec
herbicide.
1. Fill the tank 1/4 to 1/3 full of water.
2. While agitating, add the required amount of AFFINITY BroadSpec herbicide.
3. Continue agitation until the AFFINITY BroadSpec herbicide is fully dissolved, at least 5 minutes.
4. Once the AFFINITY BroadSpec herbicide is fully dissolved, maintain agitation and continue filling tank with 
water.

18 
 
5. As the tank is filling, add tank mix partners and then add the required volume of spray adjuvant. Always add 
spray adjuvant last. Antifoaming agents may be used. DO NOT use with spray additives that alter the pH of the 
spray solution below pH 6.0 as rapid product degradation can occur. Spray solutions of pH 7.0 and higher allow for 
optimum stability of AFFINITY BroadSpec herbicide.
6. Dispersed tank mix partners can settle if the tank mixture is not continually agitated. If settling occurs, thoroughly 
reagitate before using.
7. Apply AFFINITY BroadSpec herbicide spray mixture within 24 hours of mixing to avoid product degradation.
8. If AFFINITY BroadSpec herbicide and a tank mix partner are to be applied in multiple loads, fully dissolve the 
AFFINITY BroadSpec herbicide in clean water prior to adding to the tank.
GRAZING
Allow at least 7 days between application and grazing of treated forage. In addition, allow at least 7 days between 
application and feeding of forage from treated areas to livestock. Allow at least 30 days between application and 
feeding of hay from treated areas to livestock. Harvested straw may be used for bedding and/or feed. Allow at least 
45 days between application and harvesting of grain.
SPRAY EQUIPMENT
For specific application equipment, refer to the manufacturer’s instructions for additional information on GPA, 
pressure, speed, nozzle types and arrangements, nozzle heights above the target canopy, etc.
Be sure to calibrate air or ground equipment properly before application. Select a spray volume and delivery system 
that will ensure thorough coverage and a uniform spray pattern with minimum drift. Use higher spray volumes to 
obtain better coverage when crop canopy is dense. Avoid swath overlapping, and shut off spray booms while 
starting, turning, slowing, or stopping, to avoid injury to the crop. For additional information on spray drift refer to 
Spray Drift section of label.
Continuous agitation is not required for AFFINITY BroadSpec herbicide but may be required to keep tank-mix 
partners in solution or suspension. Refer to tank-mix partner labels for additional information.
SPRAYER CLEANUP
The spray equipment must be cleaned before AFFINITY BroadSpec herbicide is sprayed. Follow the cleanup 
procedures specified on the labels of the previously applied products. If no directions are provided, follow the six 
steps outlined in "After Spraying AFFINITY BroadSpec herbicide" in this label.
AT THE END OF THE DAY
It is advised that during periods when multiple loads of AFFINITY BroadSpec herbicide are applied, at the end of 
each day of spraying, the interior of the tank be rinsed with fresh water and then partially filled, and the boom and 
hoses flushed. This will prevent the buildup of dried pesticide deposits which can accumulate in the application 
equipment.
AFTER SPRAYING AFFINITY BROADSPEC HERBICIDE AND BEFORE SPRAYING CROPS 
OTHER THAN WHEAT AND BARLEY
To avoid subsequent injury to desirable crops, thoroughly clean all mixing and spray equipment immediately 
following applications of AFFINITY BroadSpec herbicide as follows:
1. Empty the tank and drain the sump completely.
2. Spray the tank walls with clean water using a minimum volume of 10% of the tank volume. Circulate the water 
through the lines, including all by-pass lines, for at least two minutes. Flush the boom well and empty the sprayer. 
Completely drain the sump.
3. Repeat step 2.
4. Remove the nozzles and screens and clean separately in a bucket containing water.
The rinsate solution may be applied to the crop(s) specified on this label. DO NOT exceed the maximum-labeled use 
rate. If cleaners are used, consult the cleaner label for rinsate disposal instructions. If no instructions are given, 
dispose of the rinsate on site or at an approved waste disposal facility.

19 
 
Notes:
1. Always start with a clean spray tank.
2. Steam-cleaning aerial spray tanks is advised to facilitate the removal of any caked deposits.
3. When AFFINITY BroadSpec herbicide is tank mixed with other pesticides, all cleanout procedures for each 
product must be examined and the most rigorous procedure must be followed.
4. In addition to this cleanout procedure, all pre-cleanout guidelines on subsequently applied products must be 
followed as per the individual labels.
MANDATORY SPRAY DRIFT
Ground Boom Applications:
• Apply with the nozzle height recommended by the manufacturer, but no more than 3 feet above the ground or crop
canopy unless making a turf, pasture, or rangeland application, in which case applicators may apply with a nozzle 
height no more than 4 feet above the ground.
• For applications prior to the emergence of crops and target weeds, applicators are required to use a Coarse or 
coarser droplet size (ASABE S572.1).
• For all other applications, applicators are required to use a Medium or coarser droplet size (ASABE S572.1).
• DO NOT apply when wind speeds exceed 10 miles per hour at the application site.
• DO NOT apply during temperature inversions.
Aerial Applications:
• DO NOT release spray at a height greater than 10 feet above the vegetative canopy, unless a greater application 
height is necessary for pilot safety.
• For applications prior to the emergence of crops and target weeds, applicators are required to use a Coarse or 
coarser droplet size (ASABE S572.1).
• For all other applications, applicators are required to use a Medium or coarser droplet size (ASABE S572.1).
• The boom length must not exceed 65% of the wingspan for airplanes or 75% of the rotor blade diameter for 
helicopters.
• Applicators must use one-half swath displacement upwind at the downwind edge of the field.
• Nozzles must be oriented so the spray is directed toward the back of the aircraft.
• DO NOT apply when wind speeds exceed 10 miles per hour at the application site.
• DO NOT apply during temperature inversions.
SPRAY DRIFT MANAGEMENT ADVISORIES
THE APPLICATOR IS RESPONSIBLE FOR AVOIDING OFF-SITE SPRAY DRIFT .
BE AWARE OF NEARBY NON-TARGET SITES AND ENVIRONMENTAL CONDITION S.
IMPORTANCE OF DROPLET SIZE
An effective way to reduce spray drift is to apply large droplets. Use the largest droplets that provide target pest 
control.
While applying larger droplets will reduce spray drift, the potential for drift will be greater if applications are made
improperly or under unfavorable environmental conditions.
Controlling Droplet Size – Ground Boom
• Volume - Increasing the spray volume so that larger droplets are produced will reduce spray drift. Use the highest 
practical spray volume for the application. If a greater spray volume is needed, consider using a nozzle with a higher 
flow rate.
• Pressure - Use the lowest spray pressure recommended for the nozzle to produce the target spray volume and 
droplet size.
• Spray Nozzle - Use a spray nozzle that is designed for the intended application. Consider using nozzles designed to 
reduce drift.
Controlling Droplet Size – Aircraft
• Adjust Nozzles - Follow nozzle manufacturers recommendations for setting up nozzles.
Generally, to reduce fine droplets, nozzles should be oriented parallel with the airflow in flight.

20 
 
BOOM HEIGHT – Ground Boom
Use the lowest boom height that is compatible with the spray nozzles that will provide uniform coverage. For 
ground equipment, the boom should remain level with the crop and have minimal bounce.
RELEASE HEIGHT - Aircraft
Higher release heights increase the potential for spray drift. When applying aerially to crops, DO NOT release spray 
at a height greater than 10 ft above the crop canopy, unless a greater application height is necessary for pilot safety.
SHIELDED SPRAYERS
Shielding the boom or individual nozzles can reduce spray drift. Consider using shielded sprayers. Verify that the 
shields are not interfering with the uniform deposition of the spray on the target area.
TEMPERATURE AND HUMIDITY
When making applications in hot and dry conditions, use larger droplets to reduce effects of evaporation.
TEMPERATURE INVERSIONS
Drift potential is high during a temperature inversion. Temperature inversions are characterized by increasing 
temperature with altitude and are common on nights with limited cloud cover and light to no wind. The presence of 
an inversion can be indicated by ground fog or by the movement of smoke from a ground source or an aircraft 
smoke generator. Smoke that layers and moves laterally in a concentrated cloud (under low wind conditions) 
indicates an inversion, while smoke that moves upward and rapidly dissipates indicates good vertical air mixing. 
Avoid applications during temperature inversions.
WIND
Drift potential generally increases with wind speed. AVOID APPLICATIONS DURING GUSTY WIND 
CONDITIONS.
Applicators need to be familiar with local wind patterns and terrain that could affect spray drift.
Handheld Technology Applications:
• Take precautions to minimize spray drift.
DRIFT CONTROL ADDITIVES
Using product compatible drift control additives can reduce drift potential. When a drift control additive is used, 
read and carefully observe cautionary statements and all other information on the additive’s label. If using an 
additive that increases viscosity, ensure that the nozzles and other application equipment will function properly with 
a viscous spray solution.
Preferred drift control additives have been certified by the Chemical Producers and Distributors Association 
(CPDA).

21 
 
______________________________________________________________________________
FOR USE IN SEED PRODUCTION OF SOYBEANS WITH BOLT TECHNOLOGY
Application and Use Rate Information
Use Rates (oz of 
AFFINITY 
BroadSpec 
herbicide per acre)
Active 
Ingredient
Pounds of Active 
Ingredient per acre
For control of broadleaf weeds and for the 
detection and control of susceptible soybean 
“segregates”, apply AFFINITY BroadSpec 
herbicide at 0.5 - 1.0 oz/A to soybeans with 
BOLT technology.
Applications of AFFINITY BroadSpec 
herbicide on soybean may be made from 
emergence through the bloom growth stage.
Best results are obtained when applications 
are made to actively growing plants.
AFFINITY BroadSpec herbicide is rainfast 
1 hour after application.
0.5 to 1.0
Thifensulfuron 
methyl
0.0078 to 0.0156
Tribenuron 
methyl
0.0078 to 0.0156
RESTRICTIONS in seed production of soybeans with BOLT Technology:
x DO NOT apply more than 1.0 oz of AFFINITY BroadSpec herbicide p er acre in a single application 
(maximum active ingredient per single application is 0.0156 lb/A thifensulfuron methyl and 0.0156 lb/A 
tribenuron methyl).
x DO NOT exceed two applications of AFFINITY BroadSpec herbicide per year in seed production of 
soybeans with BOLT Technology when using reduced application rates.
x DO NOT apply more than 1.0 oz of AFFINITY BroadSpec herbicide p er acre per year (maximum active 
ingredient load per year is 0.0156 lb/A thifensulfuron methyl and 0.0156 lb/A tribenuron methyl).
x When applying 0.4 to 0.6 oz per acre, AFFINITY BroadSpec herbicide must be used in a tank-mix 
combination with other registered herbicides.
x The Minimum Retreatment Interval is 14 days.
x Soybeans containing the BOLT trait may be replanted anytime after the application of AFFINITY 
BroadSpec herbicide. Do not graze, harvest or feed forage or grain from treated soybeans within 7 days 
of application.
PRECAUTIONS in seed production of soybeans with BOLT Technology:
Carefully observe all sprayer cleanup instructions both prior to and after using this product, as spray tank residue 
may damage crops other than soybeans with BOLT technology.
AFFINITY BroadSpec herbicide is a water-soluble herbicide applied as a foliar spray to selectively control certain 
broadleaf weeds in soybeans with BOLT technology. AFFINITY Broad Spec herbicide may also be applied to 
remove susceptible “segregates”, i.e., undesirable soybean plants that do not contain the BOLT trait, during seed 
propagation. Soybean plants not possessing the BOLT trait will be severely injured or killed if treated with 
AFFINITY BroadSpec herbicide.
TANK MIXTURES in seed production of soybeans with BOLT Technology:
When tank mixing AFFINITY BroadSpec herbicide + glyphosate herbicides, it is advised to add 4.25 -17 lb 
ammonium sulfate per 100 gallons of spray mixture. The addition of surfactant at 0.25% v/v (1 qt per 100 gallons of 
spray) to some AFFINITY BroadSpec herbicide + glyphosate tank mixes may result in improved weed control. See 
the glyphosate manufacturer's label for specific ammonium sulfate and surfactant directions.

22 
 
Weed control and crop safety resulting from the use of tank mixtures not specifically noted on this label are the 
responsibility of the user.
It is the pesticide user’s responsibility to ensure that all products are registered for the intended use. Read and follow 
the applicable restrictions, limitations and directions for use on all product labels involved in tank mixing. Users 
must follow the most restrictive directions for use and precautionary statements of each product in the tank mixture. 
If the instructions on the tank mix partner label conflict with this AFFINITY BroadSpec herbicide, then DO NOT 
use in a tank mixture with AFFINITY BroadSpec herbicide.
WEEDS CONTROLLED
In addition to detecting and controlling susceptible soybean “segregates”, AFFINITY BroadSpec herbicide also 
effectively controls the following weeds when used according to label directions:
Annual knawel
Annual sowthistle
Black mustard
Blue/Purple mustard
Broadleaf dock
Bur buttercup
Bushy wallflower/Treacle mustard
Canada thistle *
Clasping pepperweed
Coast fiddleneck
Common buckwheat
Common chickweed
Common cocklebur *
Common groundsel
Common lambsquarters
Common ragweed *
Common sunflower
Corn chamomile
Corn gromwell *
Corn spurry
Cowcockle
Cress (mouse-ear)
Curly dock
False chamomile
Field chickweed
Field pennycress
Filaree (redstem, Texas)
Flixweed
Green smartweed
Henbit
Kochia *
Ladysthumb
Lanceleaf sage *
London rocket
Marshelder
Mayweed chamomile
Miners lettuce
Narrrowleaf lambsquarters
Nightflowering catchfly
Pennsylvania smartweed
Pineappleweed
Prickly lettuce*
Prostrate knotweed
Prostrate pigweed
Redmaids
Redroot pigweed
Russian thistle*
Scentless chamomile/mayweed
Shepherd's-purse
Slimleaf lambsquarters
Smallflower buttercup
Smallseed falseflax
Stinking chickweed
Stinking mayweed/dogfennel
Sunflower
Swinecress
Tansymustard
Tarweed fiddleneck
Tumble/Jim Hill mustard
Volunteer canola
Volunteer lentils
Volunteer peas
White cockle
Wild buckwheat*
Wild chamomile
Wild mustard
*These species may be difficult to control with, or, resistant to AFFINITY BroadSpec herbicide.
______________________________________________________________________________

23 
 
IDENTIFICATION INFORMATION FOR PRODUCTS REFERENCED IN THIS LABEL
REGISTERED PRODUCTS REFERENCED IN THIS LABEL FOR TANK MIXTURES 
OR MENTIONED FOR OTHER REASONS
Product Name Active Ingredient(s) EPA Registration Number
Colt® AS herbicide Clopyralid + Fluroxypyr 34704-1019
Colt + Salvo® herbicide Fluroxypyr + 2,4-D 34704-1010
Colt + Sword® herbicide Fluroxypyr + MCPA 34704-1011
Buctril® herbicide bromoxynil 264-437
Rimfire® Max herbicide Mesosulfuron-methyl +
Propoxycarbazone-sodium 264-1099
Everest® 2.0 herbicide Flucarbazone-sodium 66330-391
Everest® 3.0 herbicide Flucarbazone-sodium 66330-429
Everest® 3.0 AG Flucarbazone-sodium 66330-433
WideMatch® herbicide Clopyralid + Fluroxypyr 62719-512
Starane® NXT herbicide Bromoxynil + Fluroxypyr 62719-557
GoldSky® herbicide Fluroxypyr, 1-methylheptyl ester + 
Florasulam + Pyroxsulam 62719-582

24 
 
STORAGE AND DISPOSAL
Do not contaminate water, food, or feed by storage and disposal.
Pesticide Storage: Store product in original container only. Store in a cool, dry place.
Pesticide Disposal: Waste resulting from the use of this product must be disposed of on site or at an approved waste
disposal facility.
Container Handling: Refer to the Net Contents section of this product’s labeling for the applicable 
“Nonrefillable Container” or “Refillable Container” designation. 
Nonrefillable Plastic and Metal Containers (Capacity Equal to or Less Than 50 Pounds): Nonrefillable 
container. Do not reuse or refill this container. Triple rinse container (or equivalent) promptly after emptying. Triple 
rinse as follows: Empty the remaining contents into application equipment or a mix tank. Fill the container 1/4 full 
with water and recap. Shake for 10 seconds. Pour rinsate into application equipment or a mix tank or store rinsate 
for later use or disposal. Drain for 10 seconds after the flow begins to drip. Repeat this procedure two more times. 
Then, for Plastic Containers, offer for recycling if available or puncture and dispose of in a sanitary landfill, or by 
incineration. Do not burn, unless allowed by state and local ordinances. For Metal Containers, offer for recycling if 
available or reconditioning if appropriate, or puncture and dispose of in a sanitary landfill, or by other procedures 
approved by state and local authorities.
Nonrefillable Plastic and Metal Containers (Capacity Greater Than 50 Pounds): Nonrefillable container. Do 
not reuse or refill this container. Triple rinse container (or equivalent) promptly after emptying. Triple rinse as 
follows: Empty the remaining contents into application equipment or a mix tank. Fill the container 1/4 full with 
water. Replace and tighten closures. Tip container on its side and roll it back and forth, ensuring at least one 
complete revolution, for 30 seconds. Stand the container on its end and tip it back and forth several times. Turn the 
container over onto its other end and tip it back and forth several times. Empty the rinsate into application 
equipment or a mix tank or store rinsate for later use or disposal. Repeat this procedure two more times. Then, for 
Plastic Containers, offer for recycling if available or puncture and dispose of in a sanitary landfill, or by incineration. 
Do not burn, unless allowed by state and local ordinances. For Metal Containers, offer for recycling if available or 
reconditioning if appropriate, or puncture and dispose of in a sanitary landfill, or by other procedures approved by 
state and local authorities.
Nonrefillable Plastic and Metal Containers, e.g., Intermediate Bulk Containers [IBC] (Size or Shape Too 
Large to be Tipped, Rolled or Turned Upside Down): Nonrefillable container. Do not reuse or refill this 
container. Clean container promptly after emptying the contents from this container into application equipment or 
mix tank and before final disposal using the following pressure rinsing procedure. Insert a lance fitted with a suitable 
tank cleaning nozzle into the container and ensure that the water spray thoroughly covers the top, bottom and all 
sides inside the container. The nozzle manufacturer generally provides instructions for the appropriate spray 
pressure, spray duration and/or spray volume. If the manufacturer’s instructions are not available, pressure rinse the 
container for at least 60 seconds using a minimum pressure of 30 PSI with a minimum rinse volume of 10% of the 
container volume. Drain, pour or pump rinsate into application equipment or rinsate collection system. Repeat this 
pressure rinsing procedure two more times. Then, for Plastic Containers, offer for recycling if available or puncture 
and dispose of in a sanitary landfill, or by incineration. For Metal Containers, offer for recycling if available or 
reconditioning if appropriate, or puncture and dispose of in a sanitary landfill, or by other procedures approved by 
state and local authorities.
Nonrefillable Paper or Plastic Bags, Fiber Sacks including Flexible Intermediate Bulk Containers (FIBC) or 
Fiber Drums With Liners: Nonrefillable container. Do not reuse or refill this container. Completely empty paper 
or plastic bag, fiber sack or drum liner by shaking and tapping sides and bottom to loosen clinging particles. Empty 
residue into application or manufacturing equipment. Then offer for recycling if available or dispose of empty paper 
or plastic bag, fiber sack or fiber drum and liner in a sanitary landfill, or by incineration. Do not burn, unless allowed 
by state and local ordinances.

25 
 
Refillable Fiber Drums With Liners: Refillable container (fiber drum only). Refilling Fiber Drum: Refill this fiber 
drum with AFFINITY BroadSpec herbicide containing thifensulfuron methyl and tribenuron methyl only. Do not 
reuse this fiber drum for any other purpose. Cleaning before refilling is the responsibility of the refiller. Completely 
empty liner by shaking and tapping sides and bottom to loosen clinging particles. Empty residue into application or 
manufacturing equipment. Disposing of Fiber Drum and/or Liner: Do not reuse this fiber drum for any other 
purpose other than refilling (see preceding). Cleaning the container (liner and/or fiber drum) before final disposal is 
the responsibility of the person disposing of the container. Offer the liner for recycling if available or dispose of 
liner in a sanitary landfill, or by incineration. Do not burn, unless allowed by state and local ordinances. If drum is 
contaminated and cannot be reused, dispose of it in the manner required for its liner. To clean the fiber drum before
final disposal, completely empty the fiber drum by shaking and tapping sides and bottom to loosen clinging 
particles. Empty residue into application or manufacturing equipment. Then offer the fiber drum for recycling if 
available or dispose of in a sanitary landfill, or by incineration. Do not burn, unless allowed by state and local 
ordinances.
All Other Refillable Containers: Refillable container. Refilling Container: Refill this container with AFFINITY 
BroadSpec herbicide containing thifensulfuron methyl and tribenuron methyl only. Do not reuse this container for 
any other purpose. Cleaning before refilling is the responsibility of the refiller. Prior to refilling, inspect carefully for
damage such as cracks, punctures, abrasions, worn out threads and closure devices. If damage is found, do not use 
the container, contact FMC at the number below for instructions. Check for leaks after refilling and before 
transporting. If leaks are found, do not reuse or transport container, contact FMC at the number below for 
instructions. Disposing of Container: Do not reuse this container for any other purpose other than refilling (see 
preceding). Cleaning the container before final disposal is the responsibility of the person disposing of the container. 
To clean the container before final disposal, use the following pressure rinsing procedure. Insert a lance fitted with a 
suitable tank cleaning nozzle into the container and ensure that the water spray thoroughly covers the top, bottom 
and all sides inside the container. The nozzle manufacturer generally provides instructions for the appropriate spray 
pressure, spray duration and/or spray volume. If the manufacturer’s instructions are not available, pressure rinse the 
container for at least 60 seconds using a minimum pressure of 30 PSI with a minimum rinse volume of 10% of the 
container volume. Drain, pour or pump rinsate into application equipment or rinsate collection system. Repeat this 
pressure rinsing procedure two more times. Then, for Plastic Containers, offer for recycling if available or puncture 
and dispose of in a sanitary landfill, or by incineration. Do not burn, unless allowed by state and local ordinances. 
For Metal Containers, offer for recycling if available or reconditioning if appropriate, or puncture and dispose of in a 
sanitary landfill, or by other procedures approved by state and local authorities.
Outer Foil Pouches of Water Soluble Packets (WSP): Nonrefillable container. Do not reuse or refill this 
container. Offer for recycling if available or, dispose of the empty outer foil pouch in the trash as long as WSP is 
unbroken. If the outer pouch contacts the formulated product in any way, the pouch must be triple rinsed with clean 
water. Add the rinsate to the spray tank and dispose of the outer pouch as described previously.
Do not transport if this container is damaged or leaking. If the container is damaged, leaking or obsolete, or in the 
event of a major spill, fire or other emergency, contact CHEMTREC (Transportation and Spills) at 1-800-424-9300, 
day or night.
NOTICE TO BUYER: Purchase of this material does not confer any rights under patents of countries outside of 
the United States.
FMC, Affinity and TotalSol are trademarks of FMC Corporation or an affiliate.
Colt, Colt + Sword, and Colt + Salvo are registered trademarks of Loveland Products, Inc
Buctril and Rimfire are registered trademarks of Bayer CropScience LP
Everest is a registered trademark of Arysta LifeScience North America LLC
BOLT, GoldSky, Starane NXT, and WideMatch are registered trademarks of Corteva Agriscience United States
D-4027 070819

26 
 
CONDITIONS OF SALE AND LIMITATION OF WARRANTY AND LIABILITY
Notice: Read the entire Directions for Use and Conditions of Sale and Limitation of Warranty and Liability before buying 
or using this product. If the terms are not acceptable, return the product at once, unopened, and the purchase price will be 
refunded. 
The Directions for Use of this product must be followed carefully. It is impossible to eliminate all risks inherently 
associated with the use of this product. Crop injury, ineffectiveness, or other unintended consequences may result because 
of such factors as manner of use or application, weather or crop conditions beyond the control of FMC or Seller. To the 
extent consistent with applicable law, all such risks shall be assumed by Buyer and User, and, to the extent consistent with 
applicable law, Buyer and User agree to hold FMC and Seller harmless for any claims relating to such factors.
Seller warrants that this product conforms to the chemical description on the label and is reasonably fit for the 
purposes stated on the Directions for Use when used in accordance with the directions under normal conditions of 
use. TO THE EXTENT CONSISTENT WITH APPLICABLE LAW, FMC MAKES NO WARRANTIES OF 
MERCHANTABILITY OR OF FITNESS FOR A PARTICULAR PURPOSE, NOR ANY OTHER EXPRESS OR 
IMPLIED WARRANTIES WITH RESPECT TO THE SELECTION, PURCHASE, OR USE OF THIS 
PRODUCT. Any warranties, express or implied, having been made are inapplicable if this product has been used 
contrary to label instructions, or under abnormal conditions, or under conditions not reasonably foreseeable to (or 
beyond the control of) Seller or FMC, and, to the extent permitted by applicable law, Buyer assumes the risk of any 
such use.
To the extent consistent with applicable law, FMC or Seller shall not be liable for any incidental, consequential or special
damages resulting from the use or handling of this product. TO THE EXTENT CONSISTENT WITH APPLICABLE 
LAW, THE EXCLUSIVE REMEDY OF THE USER OR BUYER, AND THE EXCLUSIVE LIABILITY OF FMC AND 
SELLER FOR ANY AND ALL CLAIMS, LOSSES, INJURIES OR DAMAGES (INCLUDING CLAIMS BASED ON 
BREACH OF WARRANTY, CONTRACT, NEGLIGENCE, TORT, STRICT LIABILITY OR OTHERWISE) 
RESULTING FROM THE USE OR HANDLING OF THIS PRODUCT, SHALL BE THE RETURN OF THE 
PURCHASE PRICE OF THE PRODUCT OR, AT THE ELECTION OF FMC OR SELLER, THE REPLACEMENT OF 
THE PRODUCT.
This Condition of Sale and Limitation of Warranty and Liability may not be amended by any oral or written 
agreement.
FMC Corporation, 2929 Walnut Street, Philadelphia, PA 19104
© 2009-2019 FMC Corporation. All rights reserved.