crop-chem-docs/corpus/epa_ppls/7969-485.md

# BAS 183 36 H Herbicide

- EPA Reg No: **7969-485**
- Registrant: BASF AGRICULTURAL SOLUTIONS US, LLC
- Signal word: Warning
- Active ingredients: Dicamba, potassium salt (52.88%)
- Label accepted: 2022-12-06
- Source PDF: https://www3.epa.gov/pesticides/chem_search/ppls/007969-00485-20221206.pdf

---
Registration Notice Unconditional v.20220527


U.S. ENVIRONMENTAL PROTECTION AGENCY
Office of Pesticide Programs
Registration Division (7505T)
1200 Pennsylvania Ave., N.W.
Washington, D.C. 20460

EPA Reg. Number:

7969-485

Date of Issuance:

12/6/22
NOTICE OF PESTICIDE:
 X Registration
 Reregistration

Term of Issuance:
Unconditional
 (under FIFRA, as amended)
Name of Pesticide Product:
BAS 183 36 H HERBICIDE

Name and Address of Registrant (include ZIP Code):
BASF
26 Davis Drive
Research Trian
gle Park, NC 27709

Note: Changes in labeling differing in substance from that accepted in connection with this registration must be submitted to and accepted by the
Registration Division prior to use of the label in commerce. In any correspondence on this product always refer to the above E PA registration number.

On the basis of information furnished by the registrant, the above named pesticide is hereby registered
under the Federal Insecticide, Fungicide, and Rodenticide Act (FIFRA).

Registration is in no way to be construed as an endorsement or recommendation of this product by the
Agency. In order to protect health and the environment, the Administrator, on his motion, may at any
time suspend or cancel the registration of a pesticide in accordance with the Act. The acceptance of any
name in connection with the registration of a product under this Act is not to be construed as giving the
registrant a right to exclusive use of the name or to its use if it has been covered by others.

This product is unconditionally registered in accordance with FIFRA section 3(c)(5) provided that you:

1. Submit and/or cite all data required for registration/reregistration/registration review of your
product when the Agency requires all registrants of similar products to submit such data.


Continues page 2

Signature of Approving Official:

Emily Schmid, Product Manager 25
Herbicide Branch, Registration Division (7505P)


Date:


 12/6/22
EPA Form 8570-6

Page 2 of 2
EPA Reg. No. 7969-485
Decision No. 577506


2. Make the following label changes before you release the product for shipment:

 Revise the EPA Registration Number to read, “EPA Reg. No. 7969-485.”

3. Submit one copy of the final printed label for the record before you release the product for
shipment.

Should you wish to add/retain a reference to the company’s website on your label, then please be aware
that the website becomes labeling under FIFRA and is subject to review by the Agency. If the website is
false or misleading, the product would be misbranded and unlawful to sell or distribute under FIFRA
section 12(a)(1)(E). 40 CFR 156.10(a)(5) lists examples of statements EPA may consider false or
misleading. In addition, regardless of whether a website is referenced on your product’s label, claims
made on the website may not substantially differ from those claims approved through the registration
process. Therefore, should the Agency find or if it is brought to our attention that a website contains
false or misleading statements or claims substantially differing from the EPA approved registration, the
website will be referred to the EPA’s Office of Enforcement and Compliance.

If these conditions are not complied with, the registration will be subject to cancellation in accordance
with FIFRA section 6. Your release for shipment of the product constitutes acceptance of these
conditions. A stamped copy of the label is enclosed for your records.

The record for this product currently contains the following CSF(s):

 Basic CSF dated 09/22/2021
 Alternate CSF 1 dated 09/22/2021

If you have any questions, please contact Lydia Crawford by phone at 202-566-2575, or via email at
Crawford.Lydia@epa.gov.

Enclosure

For weed control in asparagus; conservation reserve programs
(CRP); corn; cotton; fallow cropland; farmstead turf (noncropland)
and sod farms; grass grown for seed; pasture, hay, rangeland, and
farmstead (noncropland); proso millet; small grain; sorghum;
soybean; and sugarcane
NOT FOR USE ON DICAMBA TOLERANT (DT) CROPS
Active Ingredient*:
dicamba: Potassium salt of 3,6-dichloro-o-anisic acid . . . . . . . . . . . . . . . . . . . . 52 .82%
Other Ingredients: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 .18%
Total: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .100 .00%
* Contains 45 .08% dicamba (5 pounds acid equivalent per gallon or 600 grams per liter)
EPA Reg. No. 7969-XXX EPA Est. No.
KEEP OUT OF REACH OF CHILDREN
WARNING/AVISO
Si usted no entiende la etiqueta, busque a alguien para que se la explique a usted en
detalle . (If you do not understand the label, find someone to explain it to you in detail .)
See full label for complete First Aid, Precautionary Statements, Directions For Use,
Conditions of Sale and Warranty, and state-specific crop and/or use site restrictions .
In case of an emergency endangering life or property involving this product,
call day or night 1-800-832-HELP (4357).
Net Contents:
BASF Corporation
26 Davis Drive, Research Triangle Park, NC 27709
DICAMBA GROUP 4 HERBICIDE
12/6/2022
7969-485

2
Precautionary Statements
Hazards to Humans and Domestic Animals
WARNING. Causes substantial but temporary eye injury .
Harmful if swallowed . Harmful if absorbed through skin .
Harmful if inhaled . DO NOT get in eyes or on clothing .
Avoid contact with skin . Avoid breathing (dust, vapor or
spray mist) . Remove and wash contaminated clothing
before reuse . Wash hands thoroughly with soap and water
after handling and before eating, drinking, chewing gum,
using tobacco, or using the toilet .
Personal Protective Equipment (PPE)
All mixers, loaders, applicators, and other handlers
must wear:
• Long-sleeved shirt and long pants
• Shoes plus socks
• Waterproof gloves
See Engineering Controls for additional requirements .
Follow the manufacturer’s instructions for cleaning and
maintaining PPE . If no such instructions for washables
exist, use detergent and hot water . Keep and wash PPE
separately from other laundry .
Engineering Controls
When handlers use closed systems or enclosed cabs or
aircraft in a manner that meets the requirements listed in
the Worker Protection Standard (WPS) for agricultural pes-
ticides [40 CFR 170 .240(d)(4-6)], the handler PPE
requirements may be reduced or modified as specified in
the WPS .
Pilots must use cockpits in a manner that meets the
requirements listed in the Worker Protection Standard
(WPS) for agricultural pesticides (40 CFR 170 .240(d)(4-6) .
USER SAFETY RECOMMENDATIONS
Users should:
• Wash hands after handling and before eating, drinking,
chewing gum, using tobacco, or using the toilet .
• Remove clothing/PPE immediately if pesticide gets
inside . Then wash thoroughly and put on clean clothing .
• Remove PPE immediately after handling this product .
Wash the outside of gloves before removing . As soon
as possible, wash thoroughly and change into clean
clothing .
Environmental Hazards
DO NOT apply directly to water, or to areas where surface
water is present, or to intertidal areas below the mean high
water mark . DO NOT contaminate water when disposing
of equipment washwater or rinsate . Apply this product only
as directed on the label .
This chemical is known to leach through soil into ground -
water under certain conditions as a result of agricultural
use . Use of this chemical in areas where soils are perme-
able, particularly where the water table is shallow, may
result in groundwater contamination .
Ground and Surface Water Protection
Point-source Contamination
To prevent point-source contamination, DO NOT mix or
load this pesticide product within 50 feet of wells (including
abandoned wells and drainage wells), sinkholes, perennial
or intermittent streams and rivers, and natural or impound -
ed lakes and reservoirs . DO NOT apply pesticide product
within 50 feet of wells . This setback does not apply to
properly capped or plugged abandoned wells and does
not apply to impervious pad or properly diked mixing/
loading areas as described below .
Mixing, loading, rinsing, or washing operations performed
within 50 feet of a well are allowed only when conducted
on an impervious pad constructed to withstand the weight
of the heaviest load that may be on or move across the
pad . The pad must be self-contained to prevent surface
FIRST AID
If in eyes
• Hold eye open and rinse slowly and gently with water for 15 to 20 minutes .
• Remove contact lenses, if present, after first 5 minutes, then continue rinsing eye .
• Call a poison control center or doctor for treatment advice .
If swallowed
• Call a poison control center or doctor immediately for treatment advice .
• Have person sip a glass of water if able to swallow .
• DO NOT induce vomiting unless told to do so by a poison control center or doctor .
• DO NOT give anything by mouth to an unconscious person .
If on skin or
clothing
• Take off contaminated clothing .
• Rinse skin immediately with plenty of water for 15 to 20 minutes .
• Call a poison control center or doctor for treatment advice .
HOTLINE NUMBER
Have the product container or label with you when calling a poison control center or doctor or going for treatment .
You may also contact BASF Corporation for emergency medical treatment information: 1-800-832-HELP (4357) .

3
water flow over or from the pad . The pad capacity must be
maintained at 110% that of the largest pesticide container
or application equipment used on the pad and have suffi -
cient capacity to contain all product spills, equipment or
container leaks, equipment washwater, and rainwater that
may fall on the pad . The containment capacity does not
apply to vehicles delivering pesticide shipments to the
 mixing/loading site . States may have in effect additional
requirements regarding wellhead setbacks and operational
containment .
Care must be taken when using this product to prevent:
• Back-siphoning into wells
• Spills
• Improper disposal of excess pesticide, spray mixtures, or
rinsate
Check valves or antisiphoning devices must be used on all
mixing equipment .
Movement by Surface Runoff or
Through Soil
DO NOT apply under conditions which favor runoff .
DO NOT apply if soil is saturated with water or when rain-
fall that may exceed soil field capacity is forecast to occur
within 48 hours . Under some conditions, dicamba has the
potential for runoff several days after application . Poorly
draining, wet, or erodible soils with readily visible slopes
toward adjacent sensitive areas are more prone to pro-
duce runoff . When used on erodible soils, best
management practices for minimizing runoff should be
employed . Consult your local Soil Conservation Service for
recommendations in your use area .
DO NOT apply to impervious substrates including paved
or highly compacted surfaces in areas with high potential
for groundwater contamination . Groundwater contamina-
tion may occur in areas where soils are permeable or
coarse and groundwater is near the surface . DO NOT
apply to soils classified as sand with less than 3% organic
matter and where groundwater depth is shallow . To mini-
mize the possibility of groundwater contamination, carefully
follow the specified rates as affected by soil type in the
Crop-specific Information section of this label .
Movement by Water Erosion of Treated Soil
DO NOT apply this product through any type of irrigation
system including sprinkler, drip, flood, or furrow irrigation .
Ensure treated areas have received at least 1/2-inch rainfall
(or irrigation) before using tailwater for subsequent irriga-
tion of other fields .
Endangered Species
It is a federal offense to use any pesticide in a manner that
results in the death of an endangered species .
The use of any pesticide in a manner that may kill or other-
wise harm an endangered species or adversely modify
their habitat is a violation of federal law .
Directions For Use
It is a violation of federal law to use this product in a man-
ner inconsistent with its labeling . This labeling must be in
the user’s possession during application .
DO NOT apply this product in a way that will contact
workers or other persons, either directly or through drift .
Only protected handlers may be in the area during applica -
tion . For any requirements specific to your state or tribe,
consult the agency responsible for pesticide regulation .
Observe all precautions, restrictions, and limitations in this
label and the labels of products used in combination with
this product . Keep containers closed to avoid spills and
contamination .
All applicable directions, restrictions, precautions, and
Conditions of Sale and Warranty are to be followed .
AGRICULTURAL USE REQUIREMENTS
Use this product only in accordance with its labeling and
with the Worker Protection Standard, 40 CFR Part 170 .
This standard contains requirements for the protection of
agricultural workers on farms, forests, nurseries, and
greenhouses, and handlers of agricultural pesticides . It
contains requirements for training, decontamination,
notification, and emergency assistance . It also contains
specific instructions and exceptions pertaining to the
statements on this label about Personal Protective
Equipment (PPE) and restricted-entry intervals . The
requirements in this box only apply to uses of this prod-
uct that are covered by the WPS .
DO NOT enter or allow worker entry into treated areas
during the restricted-entry interval (REI) of 24 hours .
PPE required for early entry to treated areas that is per-
mitted under the Worker Protection Standard and that
involves contact with anything that has been treated,
such as, plants, soil, or water is:
• Coveralls worn over short-sleeved shirt and short
pants
• Chemical-resistant footwear plus socks
• Waterproof gloves
• Chemical-resistant headgear for overhead exposure
• Protective eyewear
NON-AGRICULTURAL USE REQUIREMENTS
The requirements in this box apply to uses of this prod-
uct that are NOT within the scope of the Worker
Protection Standard for agricultural pesticides (40 CFR
Part 170) . The WPS applies when this product is used to
produce agricultural plants on farms, forests, nurseries,
or greenhouses . DO NOT enter or allow people (or pets)
to enter the treated area until sprays have dried .
DO NOT apply this product in a way that will contact
workers or other persons, either directly or through drift .
Only protected handlers may be in the area during
application .

4
STORAGE AND DISPOSAL
DO NOT contaminate water, food, or feed by storage or
disposal . Open dumping is prohibited .
Pesticide Storage
Store in original container in a well-ventilated area sepa-
rately from fertilizer, feed, and foodstuffs . Avoid
cross-contamination with other pesticides .
BAS 183 36 H herbicide freezes around 15° F and is
stable under conditions of freezing and thawing . Product
that has been frozen should be thawed and recirculated
prior to use .
Pesticide Disposal
Wastes resulting from this product must be disposed of
on-site or at an approved waste disposal facility . Pesti-
cide, spray mixture, or rinsate that cannot be used
according to label instructions must be disposed of
according to federal, state or local procedures under
Subtitle C of the Resource Conservation and
Recovery Act . Improper disposal of excess pesticide,
spray mix, or rinsate is a violation of federal law .
Container Handling
Nonrefillable Container. DO NOT reuse or refill this
container . Triple rinse or pressure rinse container (or
equivalent) promptly after emptying; then offer for recy -
cling, if available, or reconditioning, if appropriate, or
puncture and dispose of in a sanitary landfill, or by incin -
eration, or by other procedures approved by state and
local authorities .
Triple rinse containers small enough to shake
(capacity ≤ 5 gallons) as follows: Empty the remain-
ing contents into application equipment or a mix tank
and drain for 10 seconds after the flow begins to drip . Fill
the container 1/4 full with water and recap . Shake for
10 seconds . Pour rinsate into application equipment or a
mix tank, or store rinsate for later use or disposal . Drain
for 10 seconds after the flow begins to drip . Repeat this
procedure two more times .
Triple rinse containers too large to shake
(capacity > 5 gallons) as follows: Empty the remain-
ing contents into application equipment or a mix tank . Fill
the container 1/4 full with water . Replace and tighten clo-
sures . Tip container on its side and roll it back and forth,
ensuring at least one complete revolution, for 30 sec-
onds . Stand the container on its end and tip it back and
forth several times . Turn the container over onto its other
end and tip it back and forth several times . Empty the
rinsate into application equipment or a mix tank, or store
rinsate for later use or disposal . Repeat this procedure
two more times .
(continued)
STORAGE AND DISPOSAL (continued)
Container Handling (continued)
Pressure rinse as follows: Empty the remaining con-
tents into application equipment or mix tank and continue
to drain for 10 seconds after the flow begins to drip . Hold
container upside down over application equipment or mix
tank, or collect rinsate for later use or disposal . Insert
pressure rinsing nozzle in the side of the container and
rinse at about 40 PSI for at least 30 seconds . Drain for
10 seconds after the flow begins to drip .
Refillable Container. Refill this container with pesticide
only . DO NOT reuse this container for any other purpose .
Triple rinsing the container before final disposal is the
responsibility of the person disposing of the container .
Cleaning before refilling is the responsibility of the refiller .
Triple rinse as follows: To clean the container before final
disposal, empty the remaining contents from this container
into application equipment or mix tank . Fill the container
about 10% full with water . Agitate vigorously or recirculate
water with the pump for 2 minutes . Pour or pump rinsate
into application equipment or rinsate collection system .
Repeat this rinsing procedure two more times .
When this container is empty, replace the cap and seal all
openings that have been opened during use; return the
container to the point of purchase or to a designated loca-
tion . This container must only be refilled with a pesticide
product . Prior to refilling, inspect carefully for damage
including cracks, punctures, abrasions, worn-out threads
and closure devices . Check for leaks after refilling and
before transport . DO NOT transport if this container is
damaged or leaking . If the container is damaged, or leak-
ing, or obsolete and not returned to the point of purchase
or to a designated location, triple rinse emptied container
and offer for recycling, if available, or dispose of container
in compliance with state and local regulations .
In Case of Emergency
In case of large-scale spill of this product, call:
• CHEMTREC 1-800-424-9300
• BASF Corporation 1-800-832-HELP (4357)
In case of medical emergency regarding this product, call:
• Your local doctor for immediate treatment
• Your local poison control center (hospital)
• BASF Corporation 1-800-832-HELP (4357)
Steps to take if material is released or spilled:
• Dike and contain the spill with inert material (sand, earth,
etc .) and transfer liquid and solid diking material to sepa -
rate containers for disposal .
• Remove contaminated clothing and wash affected skin
areas with soap and water .
• Wash clothing before reuse .
• Keep the spill out of all sewers and open bodies of water .

5
Product Information
BAS 183 36 H herbicide is a water-soluble herbicide that
provides postemergence and moderate rate-dependent
residual control of many annual broadleaf weeds .
BAS 183 36 H is also active on many biennial and peren -
nial broadleaf weeds as well as woody brush and vines
(refer to Table 1 for weeds controlled or suppressed) .
BAS 183 36 H can be used in specific field and row crops,
fallow and postharvest croplands, and sod farms .
BAS 183 36 H does not control grass weeds and must be
used sequentially or tank mixed with a grass herbicide for
a complete weed control program . See Tank Mixing
Information section for important information on herbi -
cide tank mixes or Crop-specific Information section(s)
for recommendations on sequential programs .
Additional state restrictions and requirements may apply .
The applicator must comply with any additional state
requirements and restrictions .
Table 1. Weeds Controlled or Suppressed
BAS 183 36 H will control or suppress the following
weeds when used at rates described in Table 2 . See addi-
tional information about weeds which are known to be
resistant to dicamba at
www.Resistance-Information.BASF.US .
Common Name Scientific Name
Annuals
Alkanet Lithospermum arvense
Amaranth, Palmer Amaranthus palmeri
Amaranth, Powell Amaranthus powellii
Amaranth, spiny Amaranthus spinosus
Aster, slender Aster subulatus
Bedstraw, catchweed Galium aparine
Beggarweed, Florida Desmodium tortuosum
Broomweed, common Gutierrezia dracunculoides
Buckwheat, tartary Fagopyrum tataricum
Buckwheat, wild Polygonum convolvulus
Buffalobur Solanum rostratum
Burclover, California Medicago polymorpha
Burcucumber Sicyos angulatus
Buttercup, corn Ranunculus arvensis
Buttercup, creeping Ranunculus repens
Buttercup, roughseed Ranunculus muricatus
Buttercup, western field Ranunculus occidentalis
Carpetweed Mollugo verticillata
Catchfly, nightflowering Silene noctiflorum
Chamomile, corn Anthemis arvensis
(continued)
Table 1. Weeds Controlled or Suppressed (continued)
Common Name Scientific Name
Annuals (continued)
Chervil, bur Anthriscus caucalis
Chickweed, common Stellaria media
Clover Trifolium spp .
Cockle, corn Agrostemma githago
Cockle, cow Vaccaria pyramidata
Cocklebur, common Xanthium strumarium
Copperleaf, hophornbeam Acalypha ostryifolia
Cornflower Centaurea cyanus
Croton, tropic Croton glandulosus
Croton, woolly Croton capitatus
Daisy, English Bellis perennis
Dragonhead, American Dracocephalum parviflorum
Eveningprimrose, cutleaf Oenothera laciniata
Falseflax, smallseed Camelina microcarpa
Fleabane, hairy Conyza bonariensis
Flixweed Descurainia sophia
Fumitory Fumaria officinalis
Goosefoot, nettleleaf Chenopodium murale
Hempnettle Galeopsis tetrahit
Henbit Lamium amplexicaule
Horseweed (Marestail) Conyza canadensis
Jacob’s-ladder Polemonium caeruleum
Jimsonweed Datura stramonium
Knawel (German moss) Scleranthus annuus
Knotweed, prostrate Polygonum aviculare
Kochia3 Kochia scoparia
Ladysthumb Polygonum persicaria
Lambsquarters, common Chenopodium album
Lettuce, miner’s Claytonia perfoliata
Lettuce, prickly Lactuca serriola
Mallow, common Malva neglecta
Mallow, Venice Hibiscus trionum
Mayweed Anthemis cotula
Morningglory, ivyleaf Ipomoea hederacea
Morningglory, tall Ipomoea purpurea
Mustard, black Brassica nigra
Mustard, blue Chorispora tenella
Mustard, tansy Descurainia pinnata
(continued)

6
Table 1. Weeds Controlled or Suppressed (continued)
Common Name Scientific Name
Annuals (continued)
Mustard, treacle Erysimum repandum
Mustard, tumble Sisymbrium altissimum
Mustard, wild Sinapis arvensis
Mustard, yellowtop Sinapis spp .
Nightshade, black Solanum nigrum
Nightshade, cutleaf Solanum triflorum
Pennycress, field Thlaspi arvense
Pepperweed, Virginia Lepidium virginicum
Pigweed, prostrate Amaranthus blitoides
Pigweed, redroot (rough) Amaranthus retroflexus
Pigweed, smooth Amaranthus hybridus
Pigweed, tumble Amaranthus albus
Pineappleweed Matricaria matricarioides
Poorjoe Diodia teres
Poppy, red horn Glaucium corniculatum
Puncturevine Tribulus terrestris
Purslane, common Portulaca oleracea
Pusley, Florida Richardia scabra
Radish, wild Raphanus raphanistrum
Ragweed, common Ambrosia artemisiifolia
Ragweed, giant Ambrosia trifida
Ragweed, lanceleaf Ambrosia bidentata
Rocket, London Sisymbrium irio
Rocket, yellow Barbarea vulgaris
Rubberweed, bitter Hymenoxys odorata
Salsify Tragopogon porrifolius
Senna, coffee Senna occidentalis
Sesbania, hemp Sesbania exaltata
Shepherd’s purse Capsella bursa-pastoris
Sicklepod Cassia obtusifolia
Sida, prickly (Teaweed) Sida spinosa
Smartweed, green Polygonum scabrum
Smartweed, Pennsylvania Polygonum pensylvanicum
Sneezeweed, bitter Helenium amarum
Sowthistle, annual Sonchus oleraceus
Sowthistle, spiny Sonchus asper
Spanish needles Bidens bipinnata
Spikeweed, common Hemizonia pungens
(continued)
Table 1. Weeds Controlled or Suppressed (continued)
Common Name Scientific Name
Annuals (continued)
Spurge, prostrate Chamaesyce humistrata
Spurry, corn Spergula arvensis
Starbur, bristly Acanthospermum hispidum
Starwort, little Stellaria graminea
Sumpweed, rough Iva ciliata
Sunflower, common (wild) Helianthus annuus
Thistle, Russian Salsola iberica
Velvetleaf Abutilon theophrasti
Waterhemp Amaranthus tuberculatus
Waterprimrose, winged Ludwigia decurrens
Wormwood Artemisia annua
Biennials
Burdock, common Arctium minus
Carrot, wild Daucus carota
Cockle, white Melandrium album
Eveningprimrose, common Oenothera biennis
Geranium, Carolina Geranium carolinianum
Gromwell Lithospermum spp .
Knapweed, diffuse Centaurea diffusa
Knapweed, spotted Centaurea maculosa
Mallow, dwarf Malva borealis
Plantain, bracted Plantago aristata
Ragwort, tansy Senecio jacobaea
Starthistle, yellow Centaurea solstitialis
Sweetclover Melilotus spp .
Teasel Dipsacus sativus
Thistle, bull Cirsium vulgare
Thistle, musk Carduus nutans
Thistle, plumeless Carduus acanthoides
Thistle, variegated (milk) Silybum marianum
Perennials1
Alfalfa Medicago sativa
Apple, tropical soda Solanum viarum
Artichoke, Jerusalem Helianthus tuberosus
Aster, spiny Aster spinosus
Aster, whiteheath Aster pilosus
Bedstraw, smooth Gallium mollugo
Bindweed, field Convolvulus arvensis
(continued)

7
Table 1. Weeds Controlled or Suppressed (continued)
Common Name Scientific Name
Perennials1 (continued)
Bindweed, hedge Calystegia sepium
Blueweed, Texas Helianthus ciliaris
Bursage, woollyleaf Ambrosia grayi
Buttercup, tall Ranunculus acris
Campion, bladder Silene vulgaris
Chickweed, field Cerastium arvense
Chickweed, mouseear Cerastium vulgatum
Chicory Cichorium intybus
Clover, hop Trifolium aureum
Dandelion, common Taraxacum officinale
Dock, broadleaf (Bitterdock) Rumex obtusifolius
Dock, curly Rumex crispus
Dogbane, hemp Apocynum cannabinum
Dogfennel (Cypressweed) Eupatorium capillifolium
Fern, bracken Pteridium aquilinum
Garlic, wild Allium vineale
Goldenrod, Canada Solidago canadensis
Goldenrod, Missouri Solidago missouriensis
Goldenweed, common Isocoma coronopifolia
Hawkweed Hieracium spp .
Henbane, black Hyoscyamus niger
Horsenettle, Carolina Solanum carolinense
Ironweed Vernonia spp .
Knapweed, black Centaurea nigra
Knapweed, Russian Centaurea repens
Lespedeza, sericea Lespedeza cuneata
Milkweed, climbing Sarcostemma cyanchoides
Milkweed, common Asclepias syriaca
Milkweed, honeyvine Ampelamus albidus
Milkweed, western whorled Asclepias subverticillata
Nettle, stinging Urtica dioica
Nightshade, silverleaf Solanum elaeagnifolium
Onion, wild Allium canadense
Plantain, broadleaf Plantago major
Plantain, buckhorn Plantago lanceolata
Pokeweed Phytolacca americana
Ragweed, western Ambrosia psilostachya
Redvine Brunnichia ovata
(continued)
Table 1. Weeds Controlled or Suppressed (continued)
Common Name Scientific Name
Perennials1 (continued)
Smartweed, swamp Polygonum coccineum
Snakeweed, broom Gutierrezia sarothrae
Sorrel, red (Sheep sorrel) Rumex acetosella
Sowthistle, perennial Sonchus arvensis
Spurge, leafy Euphorbia esula
Sundrop Oenothera perennis
Thistle, Canada Cirsium arvense
Thistle, Scotch Onopordum acanthium
Toadflax, Dalmatian Linaria genistifolia
Trumpetcreeper Campsis radicans
Vetch Vicia spp .
Waterhemlock, spotted Cicuta maculata
Waterprimrose, creeping Ludwigia peploides
Woodsorrel, creeping Oxalis corniculata
Woodsorrel, yellow Oxalis stricta
Wormwood, Louisiana Artemisia ludoviciana
Yankeeweed Eupatorium compositifolium
Yarrow, common Achillea millefolium
Woody Brush and Vines 1, 2
Alder Alnus spp .
Ash Fraxinus spp .
Basswood Tilia americana
Beech Fagus spp .
Birch Betula spp .
Cherry Prunus spp .
Chinquapin Chrysolepis chrysophylla
Cottonwood Populus deltoides
Cucumbertree Magnolia acuminata
Elm Ulmus spp .
Grape Vitus spp .
Hemlock Tsuga spp .
Hickory Carya spp .
Honeylocust Gleditsia triacanthos
Honeysuckle Lonicera spp .
Hornbeam Carpinus spp .
Huckleberry Vaccinium arboreum
Huisache Acacia farnesiana
Ivy, poison Rhus radicans
(continued)

8
Table 1. Weeds Controlled or Suppressed (continued)
Common Name Scientific Name
Woody Brush and Vines 1, 2 (continued)
Kudzu Pueraria lobata
Locust, black Robinia pseudoacacia
Maple Acer spp .
Mesquite Prosopis ruscifolia
Oak Quercus spp .
Oak, poison Rhus toxicodendron
Olive, Russian Elaeagnus angustifolia
Persimmon, eastern Diospyros virginiana
Pine Pinus spp .
Poplar Populus spp .
Rabbitbrush Chrysothamnus pulchellus
Rose, multiflora Rosa multiflorum
Sassafras Sassafras albidum
Serviceberry Amelanchier sanguinea
Spicebush Lindera benzoin
Spruce Picea spp .
Sumac Rhus spp .
Sycamore Platanus occidentalis
Tarbush Flourensia cernua
Willow Salix spp .
Witchhazel Hamamelis macrophylla
1 Suppression only .
2 Not for use in California .
3 Except dicamba resistant .
Product Stewardship Practices
• Apply BAS 183 36 H herbicide to weeds 4 inches or
less in size for best performance .
• Apply BAS 183 36 H at the labeled rate to minimize the
likelihood of weed resistance occurring . DO NOT apply
at less than the labeled rate . See Crop- specific
 Information for labeled rates by crop .
• Use BAS 183 36 H as part of a herbicide program that
includes the use of residual herbicides and herbicides
with alternate sites of action to reduce resistance selec-
tion pressure .
• Select nozzles that produce coarse to ultra-coarse
spray droplets .
• Maintain boom height 24 inches or less from target .
• Identify areas of sensitive nontarget crops/plants and
maintain proper setback distance from these areas .
Sensitive crops in agricultural and/or residential settings
can include, but are not limited to:
- non-DT soybeans
- cucumber and melons (EPA Crop Group 9)
- flowers
- fruit trees
- grapes
- ornamentals including greenhouse-grown and shade
house-grown broadleaf plants
- peanuts
- peas and beans (EPA Crop Group 6)
- peppers, tomatoes, and other fruiting vegetables
(EPA  Crop Group 8)
- potato
- sweet potato
- tobacco
• Thoroughly clean spray equipment before and after
application .
Mode of Action
Dicamba, the active ingredient in BAS 183 36 H , is a
Group 4 (WSSA) herbicide . Herbicides in this group mimic
auxin (a plant hormone) resulting in a hormone imbalance
in sensitive plants that interferes with normal plant growth
(e .g . cell division, cell enlargement, and protein synthesis) .
BAS 183 36 H is readily absorbed by leaves, roots, and
shoots; translocates throughout the plant; and accumu-
lates in areas of active growth to provide post emergence
control of emerged weeds as well as moderate residual
control of germinating weed seeds .
Any weed population may contain plants naturally resistant
to Group 4 herbicides . Weeds resistant to Group 4 herbi-
cides should be managed using effective herbicide(s) from
a different group and/or by using cultural or mechanical
practices . Report any incidence of non-performance of
this product against a particular weed species at
www.EngeniaQuestions.com . Consult your local BASF
representative, state cooperative extension service, profes -
sional consultants, or other qualified authority to determine
appropriate actions if you suspect resistant weeds . Addi-
tional information about weeds which are known to be
resistant to dicamba can be found at www.Resistance-
Information.BASF.US .
Herbicide Resistance Management
For resistance management, BAS 183 36 H contains a
Group 4 herbicide . Any weed population may contain
plants naturally resistant to Group 4 herbicides . The resis-
tant individuals may dominate the weed population if these
herbicides are used repeatedly are used repeatedly in the
same fields . Appropriate resistant-management strategies
should be followed .
To delay herbicide resistance consider:
• Avoiding the consecutive use of herbicides that have a
similar target-site-of-action on the same weed species .
• Using tank mixes or premixes with herbicides from differ -
ent target-site-of-action groups as long as the involved
products are all registered for the same use, have differ-
ent sites of action, and are both effective at the tank mix
or prepack rate on the weed(s) of concern .
• Rotate the use of BAS 183 36 H or other Group 4 herbi-
cides within a growing season sequence or among
growing seasons with different herbicide groups that
control the same weeds in a field .

9
• Basing herbicide use on a comprehensive IPM (Integrat-
ed Pest Management) program including cultural and
mechanical methods .
• Monitoring treated weed populations for loss of field effi -
cacy, and control of escapes with effective alternative
herbicides or mechanical methods .
• Identify weeds present in the field through scouting and
field history and understand their biology . The weed-
control program needs to consider all of the weeds
present .
• Scout fields prior to application to identify the weed spe -
cies present and their growth stage to determine if the
intended application will be effective .
• Scout fields after application to verify the treatment was
effective .
• Suspected herbicide-resistance weeds may be identified
by these indicators:
1 . Failure to control a weed species normally controlled
by the herbicide at the dose applied, especially if con -
trol is achieved on adjacent weeds;
2 . A spreading patch of non-controlled plants of a partic-
ular weed species; and
3 . Surviving plants mixed with controlled individuals of
the same species .
• If resistance is suspected, treat weed escapes with an
herbicide with a different MOA and/or use nonchemical
methods to remove escapes, as practical, with the goal
of preventing further seed production .
• Report any incidence of non-performance of this product
against a particular weed species to your BASF
representative .
• Contacting your local extension specialist, certified crop
advisors, and/or manufacturer for herbicide resistance
management and/or integrated weed management
directions for specific crops and resistant weed biotypes .
• For more information about weeds that are known to be
resistant to dicamba go to
www.Resistance-Information.BASF.US .
Crop Tolerance
Crops growing under normal environmental conditions are
tolerant to BAS 183 36 H herbicide when applied
according to label directions . Crop injury may occur under
stressful growing conditions (e .g . low soil fertility, seedling
disease, extreme hot or cold weather, excessive moisture,
high soil pH, high soil salt concentration, drought) .
Application Instructions
Apply BAS 183 36 H by ground to actively growing weeds
as a band, broadcast, or spot spray application for poste-
mergence control of emerged weeds as well as moderate
residual control of germinating weed seeds .
Make postemergence applications of BAS 183 36 H when
broadleaf weeds are small and actively growing . An
 adjuvant is recommended with BAS 183 36 H for best
post emergence activity; refer to Tank Mixing
 Information section and Crop-specific Information
sections for details . Postemergence activity may be
slowed or reduced under cloudy and/or foggy or cooler
weather conditions, or when weeds are growing under
drought or other stress conditions . When targeting dense
weed populations and/or larger broadleaf weeds, use
higher spray volumes and a higher application rate within
an application rate range .
Cultivation should be delayed until 7 days after applying
BAS 183 36 H or a reduction in weed control may occur .
Use extreme care when applying BAS 183 36 H to pre-
vent injury to desirable plants . BAS 183 36 H may cause
injury to desirable sensitive plants when contacting their
roots, stems, or foliage .
Application Rates
Always read and follow crop-specific use directions .
Table 2. Application Rate to Control or Suppress
Target Weed by Weed Type and Growth Stage
BAS 183 36 H must always be tank mixed with an adju-
vant when used for control of emerged broadleaf weeds .
(See Crop-specific Information section for additional
directions and exceptions)
Weed Type and Growth Stage
Rate/Acre2,5
(fl ozs)
Annual
Small, actively growing1
(less than 4-inches tall) 3 .2 to 12 .8
Small, actively growing
(less than 4-inches tall)
plus moderate residual control
12 .8 to 25 .6
Biennial
Rosette diameter 1 to 3 inches1 6 .4 to 12 .8
Rosette diameter more than 3 inches 12 .8 to 25 .6
Bolting 25 .6
Perennial3
Top growth suppression 6 .4 to 12 .8
Top growth control and root suppression 12 .8 to 25 .6
Woody Brush and Vines 3,4
Top growth suppression/control 12 .8 to 25 .6
1 Although rates below 12 .8 fl ozs/A (refer to crop-specific sec -
tions of the label for minimum use rates) may provide adequate
control of annual and biennial weeds, for optimum performance use
the higher listed rates or apply the lower listed rate as a tank mix with
other herbicides that are effective on the same species and biotype .
2 Use the higher rate within listed ranges when treating weeds resis -
tant to other sites of action, dense vegetative growth, or weeds with
a well-established root system . The higher rates also provide moder-
ate residual annual weed control .
3 BAS 183 36 H will suppress the top growth of herbaceous perennial
and woody brush and vines and can be combined with other herbi -
cides to improve control .
4 Not for use in California .
5 DO NOT broadcast-apply more than 25 .6 fl ozs/A per application .
Retreatment or tank mixes may be necessary for best control of
some weeds . However, sequential applications must not exceed a
maximum cumulative total of 51 .2 fl ozs/A of BAS 183 36 H
(2 pounds dicamba ae/A) per year .

10
Application Methods and Equipment
Apply BAS 183 36 H herbicide by ground or by air . Thor-
ough spray coverage is important for best broadleaf weed
control and can be improved with adjuvant, nozzle, and
spray volume selection . A spray adjuvant must always be
used with BAS 183 36 H when applying for the control of
emerged broadleaf weeds .
Calibrate application equipment for accurate target spray
volume and application rate to ensure uniform distribution of
spray and to avoid spray drift to nontarget areas . Adjust
equipment to maintain continuous agitation during spraying
with good mechanical or bypass agitation . Avoid overlaps
that will increase rates above the labeled use rates .
BAS 183 36 H may be applied using water; consult
crop-specific information sections of this label for other
spray carrier options .
Aerial Application Methods and Equipment
Water Volume: Use 1 to 10 gallons of water per acre (2 to
20 gallons of diluted spray per treated acre for preharvest
uses) . Use the higher spray volume when treating dense or
tall vegetation .
Application Equipment: Select nozzles designed to pro-
duce minimal amounts of fine spray particles . Make aerial
applications at the lowest safe height to reduce exposing
the spray to evaporation and wind . The applicator must
follow the most restrictive use cautions to avoid drift haz-
ards, including those found in this labeling, as well as state
and local regulations and ordinances . DO NOT use aerial
equipment if spray particles can be carried by the wind
into areas where sensitive crops or plants are growing or
when temperature inversions exist .
Ground Application
Banding Applications
When applying BAS 183 36 H by banding, use the follow-
ing formula to calculate the amount of herbicide and water
volume needed:
Bandwidth in inches x Broadcast
rate per acre = Banding herbicide
rate per acreRow width in inches
Bandwidth in inches x Broadcast
volume per acre = Banding water
volume per acreRow width in inches
Broadcast Applications
Unless noted in the crop-specific information section, use
a spray volume of 15 gallons of water or more per treated
acre . Thorough coverage of existing vegetation is essential
for postemergence applications; higher spray volumes may
be necessary for optimum performance .
Wiper Applications
BAS 183 36 H may be applied through wiper application
equipment to control or suppress actively growing
broadleaf weeds, brush, and vines . Use a 50% solution
containing 1 part BAS 183 36 H to 1 part water .
• DO NOT apply more than 25 .6 fl ozs/A of BAS 183 36 H
[1 .0 pound dicamba acid equivalent (ae) per acre] per
application .
• DO NOT contact desirable vegetation with herbicide solu-
tion . Wiper application may be made to crops (including
pastures) and noncropland areas described in this label .
EXCEPTION: DO NOT use wiper application on cotton,
sorghum, or soybean .
Spray System Equipment Clean-out
The applicator must ensure that the spray system used to
apply BAS 183 36 H is clean before application . Addition-
ally, small quantities of ammonium sulfate (AMS) can
increase the volatility potential of BAS 183 36 H . Be sure
that any spray mixture from a prior application that con -
tains AMS is drained and rinsed from the sprayer . After
using BAS 183 36 H , clean all mixing and spray equip -
ment (including tanks, pumps, lines, filters, screens, and
nozzles) with a strong detergent based sprayer cleaner .
Severe crop injury may occur if any BAS 183 36 H
remains in the spray equipment following application and is
subsequently applied to sensitive crops . Dispose of rinsate
in compliance with local, state, and federal guidelines .
1 . After spraying, drain the sprayer (including boom and
lines) . Avoid allowing the spray solution to remain in the
spray boom lines overnight or for extended periods of
time .
2 . Flush tank, hoses, boom, and nozzles with clean water .
Open boom ends and flush if so equipped .
3 . Inspect and clean all strainers, screens, and filters .
4 . Use commercial sprayer cleaner containing strong
detergents according to the manufacturer’s directions .
5 . Wash all parts of the tank, including the inside top sur-
face . Start agitation in the sprayer and thoroughly
recirculate the cleaning solution for at least 15 minutes .
All visible deposits must be removed from the spraying
system .
6 . Flush hoses, spray lines, and nozzles with the cleaning
solution for at least 1 minute . Remove nozzles,
screens, and strainers, and clean separately in the
cleaning solution after completing the above
procedure .
 7 . Drain pump, filter, and lines .
8 . Triple rinse the complete spraying system with clean
water .
9 . Clean and rinse the exterior of the sprayer .
10 . Appropriately dispose of all rinsate in compliance with
local, state, and federal requirements .
Spray Drift Management
Avoiding spray drift at the application site is the responsibili-
ty of the applicator . The spray system and weather- related
factors determine the potential for spray drift . The applicator
is responsible for considering these factors when making
application decisions to avoid spray drift onto nontarget
areas .

11
Applicators must follow application requirements to avoid
spray drift hazards, including those found in this labeling
and applicable state and local regulations and ordinances .
Where states have more stringent regulations, they must
be observed .
All application equipment must be properly maintained and
calibrated using appropriate carriers .
DO NOT allow herbicide solution to drip, physically drift, or
splash onto desirable vegetation because severe injury or
destruction to desirable broadleaf plants could result . The
following physical spray drift management requirements
must be followed .
Controlling Droplets
Drift potential may be reduced by applying large droplets
that provide sufficient coverage and control . Applying larg-
er droplets can reduce drift potential, but will not prevent
drift if the application is made improperly, or under unfa -
vorable environmental conditions (see the Temperature
Inversions and the Wind Speed and Direction
Requirements sections) .
• Nozzle Type - Use nozzles that produce course to ultra
course spray droplets and minimize the production of
fine droplets .
• Pressure - DO NOT exceed the nozzle manufacturer’s
specified pressures . For many nozzle types, lower pres-
sure produces larger droplets . When higher flow rates
are needed, use higher flow rate (large orifice) nozzles
instead of increasing pressure . Ensure sprayer rate con-
troller hardware (if so equipped) does not allow pressure
increases above the desired range .
• Spray Volume - Apply this product in a minimum of
15 gallons of spray solution per acre . Use a higher spray
volume when treating dense vegetation . Higher spray
volumes may also allow the use of larger nozzle orifices
(sizes) which produce coarser spray droplets .
• Equipment Ground Speed - Select a ground speed
that will deliver the desired spray volume while maintain -
ing the desired spray pressure, but DO NOT exceed a
ground speed of 15 miles per hour . Slower speeds gen-
erally result in better spray coverage and deposition on
the target area . It is recommended that ground speed be
reduced to 5 miles per hour when making applications to
the edge of the treatment area .
• Spray Boom Height - Spray at the appropriate boom
height based on nozzle selection and nozzle spacing, but
DO NOT exceed a boom height of 24 inches above target
pest or crop canopy . Set boom to lowest effective height
over the target pest or crop canopy based on equipment
manufacturer’s directions . Automated boom height con-
trollers are recommended with large booms to better
maintain optimum nozzle to canopy height . Excessive
boom height will increase the potential for spray drift .
• Hooded Spray Booms - Hooded spray booms are
another tool that can be used to minimize spray drift
potential . BAS 183 36 H herbicide may be applied
using a hooded spray boom in combination with
approved nozzles; however, the applicator must ensure
the configuration is compatible with equipment used .
Temperature Inversions
• DO NOT apply BAS 183 36 H when temperature inver-
sions exist at the field level .
Temperature inversions increase drift potential by reducing
atmospheric mixing and dispersion of any suspended
spray mixture . Suspended spray residues can move in
unpredictable directions because of the light, variable
winds common during inversions . Temperature inversions
are characterized by increasing temperatures with altitude
and are common on nights with limited cloud cover and
light-to-no wind .
Inversions begin to form as the sun sets and often contin-
ue into the morning before surface warming . Their
presence can be indicated by ground fog, smoke not ris-
ing, dust hanging over a road, or presence of dew or frost .
Smoke that layers and moves laterally (under low wind
conditions) indicates an inversion, while smoke that moves
upward and rapidly dissipates indicates good vertical air
mixing . Inversion conditions typically dissipate with
increased winds (above 3 MPH) or when surface air begins
to warm (3° F from morning low) .
Treatment Zone Awareness (Sensitive Areas,
Sensitive Crops and Residential Areas)
Sensitive Areas
BAS 183 36 H should only be applied when there is low
 potential for drift to sensitive areas (see Definitions) . It is
best to apply when the wind is blowing away from sensi-
tive areas .
Sensitive Crops and Residential Areas
• DO NOT apply under circumstances where spray drift
may occur to food, forage, or other plantings that might
be damaged or the crops thereof rendered unfit for sale,
use or consumption .
• During application and sprayer clean-out, DO NOT allow
contact of herbicide with foliage, green stems, exposed
non-woody roots of crops, and desirable plants .
• Downwind and Shifting Winds
- DO NOT apply when wind is blowing in the direction of
neighboring sensitive crops or residential areas .
- The appropriate distance must be determined by
the applicator relative to where the application is being
made, the environmental conditions, and the potential
risk to downwind sensitive crops and residential areas .
- The applicator also must be aware that WIND
 DIRECTION may vary during the application . If wind
direction shifts such that the wind is blowing toward
neighboring sensitive crops or residential areas, STOP
the application .
Survey the area before spraying: Small amounts of
spray drift that may not be visible may injure sensitive
broadleaf plants . Before making an application, the appli-
cator must survey the application site for neighboring
sensitive crops and residential areas . The applicator must
consult sensitive crop registries where available . Plant

12
injury could occur if contact between this product and
these crops/plants occurs . See www.driftwatch.org or
other sensitive crop registry websites for more information
on possible sensitive sites near your application location .
AVOIDING SPRAY DRIFT AT THE APPLICATION SITE
IS THE RESPONSIBILITY OF THE APPLICATOR.
The interaction of equipment and weather related factors
must be monitored to maximize performance and on-
target spray deposition . The applicator is responsible for
considering all of these factors when making a spray deci -
sion . The applicator is responsible for compliance with
state and local pesticide drift regulations .
Definitions
• Sensitive Areas - Bodies of water and nonresidential,
uncultivated areas that may harbor sensitive plant
species .
• Sensitive Crops and Residential Areas - Food,
 forage, or other plantings grown for sale, use or con-
sumption . Sensitive crops/plants also can be present in
nonagricultural settings, including residential areas .
 Examples include, but are not limited to:
- non-DT soybeans
- cucumber and melons (EPA  Crop Group 9 )
- flowers
- fruit trees
- grapes
- ornamentals including greenhouse-grown and shade
house-grown broadleaf plants
- peanuts
- peas and beans (EPA  Crop Group 6 )
- peppers, tomatoes, and other fruiting vegetables
(EPA  Crop Group 8 )
- potato
- sweet potato
- tobacco
Severe injury or destruction could occur if any contact
between this product and these crops/plants occurs .
Wind Speed and Direction Requirements
• Wind Speed - 3 to 15 mph
• Wind Direction - Local terrain can influence wind pat-
terns . Every applicator must be familiar with local wind
patterns and how they affect drift .
Tank Mixing Information
BAS 183 36 H herbicide may be tank mixed with other
products that are not prohibited on this label and are
approved for use on the target crop or area .
A spray adjuvant should always be used with
BAS 183 36 H when applying for the control of emerged
broadleaf weeds .
To improve postemergence weed control with
BAS 183 36 H , a Chemical Producers and Distributors
 Association (CPDA) certified adjuvant may be used . Some
adjuvants have the potential to cause crop injury under
certain conditions, at certain growth stages and/or under
other circumstances . Read all labels for products used in
the tank mixture prior to use to determine the potential for
crop injury .
Surfactants and Spreaders
Nonionic Surfactants/Spreaders (NIS)
Use an agriculturally approved nonionic surfactant
 (containing at least 80% active ingredient) at 1 to
2 pints/100 gallons [0 .12 to 0 .25% volume/volume (v/v)] .
Use the highest rate of NIS when using the lower rate
ranges of a tank mix or when treating more mature and
difficult-to-control weeds or dense vegetative growth .
OR
Oil Concentrate Surfactants
(COC, HSOC, MSO)*
Instead of NIS, oil concentrate may be used at 1 to
2 quarts/100 gallons (0 .5% to 1% v/v), but at least
 1 pint/acre . (alternate text: DO NOT use oil concentrate for
postemergence in-crop applications unless specifically
allowed in the Crop-specific Information section of this
label) .
A crop oil concentrate must contain either a petroleum-oil
or vegetable-oil base and must:
• Be non-phytotoxic
• Contain only EPA-exempt ingredients
• Provide good mixing quality in the jar test
• Be successful in local experience
Petroleum-oil and vegetable-oil concentrates should con -
tain emulsifiers to provide good mixing quality . Highly
refined vegetable oils have proven more satisfactory than
unrefined vegetable oils .
* COC - crop oil concentrate
HSOC - high surfactant oil concentrate
MSO - methylated seed oil
Warnings and Restrictions:
• Some COC, HSOC and MSO adjuvants may cause a
temporary crop response .
• DO NOT tank mix products containing ammonium salts
including ammonium sulfate and urea ammonium nitrate
(UAN) .
• DO NOT add adjuvants that will further decrease pH or
acidify the spray solution .
• Spray mixtures with lower pH levels (less than pH 5) can
increase the potential volatility of dicamba . To mitigate
this potential it is important to know the pH of your spray
mixture and make appropriate adjustments . Talk with
your local agricultural consultant, extension agent, or
BASF representative for recommendations to prevent
low pH spray mixtures .
• Use of an approved neutral buffering agent may be warrant-
ed if the water source or tank mix components will create
an acidic spray solution less than pH 5 . Possible ways to
check the pH of the spray mixture is with a litmus paper test
or pH meter . If the pH needs to be increased then consider
using an approved neutral buffering agent .
• Hard water does not usually affect the activity of
BAS 183 36 H ; however, other tank mix components

13
may be adversely affected (e .g . glyphosate) . Use of an
approved conditioning agent should be considered when
hard water (i .e . total calcium, magnesium, and iron con-
tent above 500 ppm) is used as a spray carrier .
• Drift reduction agents can minimize the percentage of
driftable fines . However, the applicator must check with
the DRA manufacturer to determine if the DRA will work
effectively with the spray nozzle, the spray pressure, and
the desired spray solution .
Refer to the tank mix product labels to confirm that the
respective tank mix products are registered for the specific
crop use; follow required crop rotation restrictions . Read
and follow the applicable restrictions and limitations and
Directions For Use on all product labels involved in tank
mixing . Always follow the most restrictive label use direc-
tions; refer to crop-specific information section for details .
Mixing BAS 183 36 H herbicide with postemergence
grass (graminicide) herbicides may reduce the effective -
ness of those products . Follow graminicide label when
mixing with BAS 183 36 H to ensure optimum weed con-
trol . Physical incompatibility, reduced weed control, or
crop injury may result from mixing BAS 183 36 H with
other pesticides, additives, nutritionals, etc .
Compatibility Test for Mix Components
Before mixing components, always perform a compatibility
jar test .
1 . For 20 gallons per acre spray volume, use 3 .3 cups
(800 mL) of water . For other spray volumes, adjust rates
accordingly . Only use water from the intended source at
the source temperature .
2 . Add components in the sequence indicated in the fol -
lowing Mixing Order instructions using 2 teaspoons for
each pound or 1 teaspoon for each pint of labeled use
rate per acre .
3 . Cap the jar and invert 10 cycles between component
additions .
4 . When the components have all been added to the jar,
let the solution stand for 15 minutes .
5 . Evaluate the solution for uniformity and stability . The
spray solution should not have free oil on the surface;
fine particles that precipitate to the bottom; or thick
(clabbered) texture . If the spray solution is not
 compatible, repeat the compatibility test with the
 addition of a suitable compatibility agent . If the solution
is then compatible, use the compatibility agent as
directed on its label . If the solution is still incompatible,
DO NOT mix the ingredients in the same tank .
Mixing Order
Make sure each component is thoroughly mixed and sus -
pended before adding tank mix partners . Except when
mixing products in PVA bags, maintain constant agitation
during mixing and application .
1 . Water - Begin by agitating a thoroughly clean sprayer
tank 1/2 to 3/4 full of clean water .
2 . Inductor - If an inductor is used, rinse it thoroughly
after each component has been added .
3 . Products in PVA bags - Place any product contained
in water-soluble PVA bags into the mixing tank . Wait
until all water-soluble PVA bags have fully dissolved and
the product is evenly mixed in the spray tank before
 continuing .
4 . Water-soluble products and additives
(BAS 183 36 H)
5 . Water-dispersible products (including dry flowables,
wettable powders, suspension concentrates, or
suspo-emulsions)
6 . Emulsifiable concentrates (including NIS and oil
 concentrate)
7 . Remaining quantity of water
Maintain continuous and constant agitation throughout mix-
ing and application until spraying is completed . If the spray
mixture is allowed to settle for any period of time, thorough
agitation is essential to resuspend the mixture before spray-
ing is resumed . Continue agitation while spraying .
Use Precautions
• Stress - Application to crops under stress because of
lack of moisture, hail damage, flooding, herbicide injury,
mechanical injury, or widely fluctuating temperatures may
result in crop injury .
• Rainfast Period - BAS 183 36 H is rainfast 4 hours
after application . Postemergence activity may be
reduced if rain or irrigation occurs within 4 hours of
application .
Use Restrictions
Applicator MUST ALSO follow restrictions under
Crop-specific Information section(s).
• Maximum Annual Use Rate - Refer to crop-specific
information sections for maximum annual application
rates for each crop or use pattern . DO NOT exceed
51 .2 fl ozs (2 .0 pounds dicamba acid equivalent) per acre
per year .
• DO NOT apply BAS 183 36 H with ammonium-
containing additives, conditioners, or fertilizers (e .g . AMS,
UAN) . Small quantities of AMS can greatly increase the
volatility potential of dicamba .
• DO NOT apply BAS 183 36 H if wind speed is greater
than 15 mph .
• DO NOT treat or contaminate irrigation ditches or water
used for domestic purposes .
• DO NOT apply BAS 183 36 H through any type of irriga-
tion system (e .g . chemigation) .
• DO NOT tank mix BAS 183 36 H with Lorsban®
insecticide .

14
Crop Rotation Restrictions
Use the following information to determine the required
interval between BAS 183 36 H herbicide application
and rotational crop planting as well as replanting after crop
failure because of environmental factors including drought,
frost, or hail . Determine the rotational crop interval for tank
mix products and use the most restrictive interval of all
products applied .
Crop Rotational Restrictions:
The interval between application and planting rotational
crop is given below . Always exclude counting days when
the ground is frozen . Planting at intervals less than speci-
fied below may result in crop injury . Moisture is essential
for the degradation of this herbicide in soil . If dry weather
prevails, use cultivation to allow herbicide contact with
moist soil .
Planting/replanting restrictions for BAS 183 36 H
applications of 19.2 fl ozs per acre or less: No rota-
tional cropping restrictions apply at 120 days or more
following application . Additionally, for annual crop uses in
this label including corn, cotton, sorghum, and soybean,
follow the preplant use directions in section BAS 183 36 H
Crop-specific Use Directions . For barley, oat, wheat,
and other grass seedings, the interval between application
and planting is 15 days per 6 .4 fl ozs per acre applied east
of the Mississippi River and 22 days per 6 .4 fl ozs per acre
west of the Mississippi River .
Planting/replanting restrictions for applications of
more than 19.2 fl ozs and up to 51.2 fl ozs of
BAS 183 36 H per acre: Corn, sorghum, cotton (east of
the Rocky Mountains) and all other crops grown in areas
with 30 inches or more of annual rainfall may be planted
120 days or more after application . Barley, oat, wheat, and
other grass seedings, may be planted if the interval from
application to planting is 30 days per 12 .8 fl ozs per acre
east of the Mississippi River and 45 days per 12 .8 fl ozs
per acre west of the Mississippi River . For all other crops in
areas with less than 30 inches of annual rainfall, the inter-
val between application and planting is 180 days or more .
BAS 183 36 H
Crop-specific Use Directions
Read product information, application instructions, weeds
controlled, and additive instructions in preceding sections
of the label .
Depending on specific crop application directions,
BAS 183 36 H may be applied for postemergence control
of emerged broadleaf weeds and/or residual control of
 germinating broadleaf weed seeds before crop planting
(preplant and/or preseed) and after planting (pre -
emergence, postemergence) . Refer to Table 1 for list of
weeds controlled or suppressed .
Asparagus
BAS 183 36 H may be applied immediately after cutting
asparagus but at least 24 hours before the next cutting .
Apply 6 .4 to 12 .8 fl ozs/A of BAS 183 36 H in 40 to 60 gal-
lons of diluted spray to emerged and actively growing
weeds . Apply 12 .8 fl ozs/A of BAS 183 36 H to control
common chickweed, field bindweed, nettleleaf goosefoot,
and wild radish . To improve control of Canada thistle and
field bindweed, apply BAS 183 36 H in combination with
 glyphosate (e .g .  Roundup® herbicide) or sequentially
with 2,4-D .
Avoid application to emerged spears . If spray contacts
emerged spears, crooking (twisting) of some spears may
result . If crooking occurs, discard affected spears .
Asparagus Restrictions
• DO NOT apply over the top to emerged spears or ferns .
• DO NOT apply more than 12 .8 fl ozs/A of BAS 183 36 H
(0 .5 pound dicamba ae/A) in a single application .
• DO NOT make more than one application per year .
• DO NOT apply more than a total of 12 .8 fl ozs/A of
BAS 183 36 H (0 .5 pound dicamba ae/A) per year in
 asparagus .
• DO NOT harvest for 24 hours after treatment .
• DO NOT use in the Coachella Valley of California .
Between Crop Application
BAS 183 36 H may be used as a burndown treatment to
control broadleaf weeds at any time of the year during the
fallow period following crop harvest and before the follow -
ing crop is planted . Apply BAS 183 36 H as a broadcast
or spot treatment to emerged and actively growing weeds
after crop harvest (postharvest) and before a killing frost,
or in fallow cropland or crop stubble the following spring or
summer .
Application Rates and Timings
Apply BAS 183 36 H as a broadcast or spot treatment at
3 .2 to 25 .6 fl ozs/A plus specified adjuvants; see Tank
Mixing Information section for details . Refer to Table 2

15
to determine use rates for specific targeted weed species .
For best performance, apply BAS 183 36 H herbicide
when annual weeds are less than 4-inches tall, when bien -
nial weeds are in the rosette stage, and to perennial weed
regrowth in late summer or fall following a mowing or till-
age treatment . For the most effective control of upright
perennial broadleaf weeds for example Canada thistle and
Jerusalem artichoke, apply BAS 183 36 H when the
majority of weeds have at least 4 inches of regrowth, or for
weeds for example field bindweed and hedge bindweed
that are in or beyond the full bloom stage .
Avoid disturbing treated areas following application . Treat-
ments may not kill weeds that develop from seed or
underground plant parts, for example rhizomes or bulblets,
after the effective period for BAS 183 36 H . For seedling
control, a follow-up program or other cultural practices
should be instituted . For small grain in-crop uses of
BAS 183 36 H , refer to Small Grain section for details .
Specific crop rotation intervals must be observed between
an application of BAS 183 36 H and planting the following
crop; see Crop Rotation Restrictions in Use
 Restrictions section .
Use with Other Herbicides
Broad-spectrum burndown control of grass weeds and/or
additional broadleaf weeds requires another herbicide .
BAS 183 36 H may be applied sequentially with one or
more of, but not limited to, the following herbicide
 products:
• Distinct ® herbicide
• Facet® L herbicide
• Outlook® herbicide
• Sharpen® powered by Kixor® herbicide
• Verdict® powered by Kixor® herbicide
• 2,4-D
• glyphosate (e .g . Roundup® herbicide)
It is the pesticide user’s responsibility to ensure that all
products are registered for the intended use . Read and
follow the applicable restrictions and limitations and direc -
tions for use on all product labels involved in tank mixing .
Users must follow the most restrictive directions for use
and precautionary statements of each product in the tank
mixture .
Between Crop Application Restrictions
• DO NOT apply more than 25 .6 fl ozs/A (1 .0 pound
 dicamba ae/A) in a single application of BAS 183 36 H
as a between crop application .
• DO NOT apply more than a maximum cumulative total of
2 pounds dicamba ae/A from all product sources per
year .
Conservation Reserve Program (CRP)
BAS 183 36 H may be used on both newly seeded and
established grasses grown in the Conservation Reserve or
federal Set-Aside Programs . Treatment with BAS 183 36 H
will injure or may kill alfalfa, clovers, lespedeza, wild winter
peas, vetch, and other legumes .
Application Rates and Timings
BAS 183 36 H may be applied at 3 .2 to 12 .8 fl ozs/A; refer
to Table 2 for rates based on target weed type and
growth stage .
Newly Seeded Areas
BAS 183 36 H may be applied either preplant or poste-
mergence to newly seeded grasses or small grain
including barley, oats, rye, sudangrass, wheat, or other
grain species grown as a cover crop . Postemergence
application may be made after seedling grasses exceed
the 3-leaf stage .
Preplant Intervals. Preplant applications at 12 .8 fl ozs/A
may injure new seedings if the interval between application
and grass planting is less than:
• 20 days - 30 inches or more annual precipitation
• 45 days - less than 30-inches annual precipitation
Established Grass Stands
Established grass stands are perennial grasses planted
one or more seasons before treatment . Certain species
(bentgrass, buffalograss, carpetgrass, St . Augustinegrass,
or smooth brome) may show a response when treated
with BAS 183 36 H when treated with more than
12 .8 fl ozs/A .
Use with Other Herbicides
Broad-spectrum control of broadleaf and grass weeds
requires another herbicide . BAS 183 36 H may be applied
sequentially with one or more of, but not limited to, the fol-
lowing herbicide products:
• Facet L
• atrazine
• glyphosate (e .g . Roundup)
• paraquat (e .g . Gramoxone® SL herbicide)
It is the pesticide user’s responsibility to ensure that all
products are registered for the intended use . Read and
follow the applicable restrictions and limitations and direc -
tions for use on all product labels involved in tank mixing .
Users must follow the most restrictive directions for use
and precautionary statements of each product in the tank
mixture .
CRP Restrictions
• DO NOT apply more than 25 .6 fl ozs/A of BAS 183 36 H
(1 .0 pound dicamba ae/A) per application .
• Allow a minimum of 7 days between applications .
• DO NOT apply more than a maximum cumulative total of
51 .2 fl ozs/A of BAS 183 36 H (2 pounds dicamba ae/A)
per year .
• BAS 183 36 H may injure newly seeded grasses and
certain species, including bentgrass, buffalograss, car -
petgrass, St . Augustinegrass, or smooth brome .

16
Corn (field, seed, silage) and Popcorn
BAS 183 36 H herbicide may be applied preplant sur-
face, preemergence, or postemergence to corn . Corn in
this label refers to conventional field corn (grown for grain,
seed, or silage) and popcorn . Before applying
BAS 183 36 H to seed corn or popcorn, verify with your
local seed company (supplier) the selectivity of
BAS 183 36 H on your inbred line or hybrid to help avoid
potential injury to sensitive inbreds or hybrids .
BAS 183 36 H is not registered for use on sweet
corn.
Direct contact of BAS 183 36 H with corn seed must be
avoided . If corn seeds are less than 1 .5 inches below the
soil surface, delay application until corn has emerged .
Postemergence applications of BAS 183 36 H to corn
during periods of rapid growth may result in temporary
leaning . Corn will usually become erect within 3 to 7 days .
To avoid breakage, delay cultivation until after corn is
growing normally .
Application Rate
BAS 183 36 H application rates vary by soil texture,
organic matter, and application timing . Refer to Table 3 for
 BAS 183 36 H application rates by application timing . Up
to 2 applications of BAS 183 36 H may be made per year .
Sequential applications must be separated by 2 weeks or
more .
Table 3. BAS 183 36 H Application Rates for Corn
Soil Texture Organic Matter
Application Rate
(fl ozs/A)
Preplant/
Preemergence 2 Preemergence Postemergence
No Tillage Conventional/
Reduced Tillage Early3 Late4
Coarse1 All 6 .4 NA 6 .4 6 .4
Medium/Fine 2 .5% or less 6 .4 NA 6 .4 to 12 .8 6 .4
Medium/Fine more than 2 .5% 12 .8 12 .8 6 .4 to 12 .8 6 .4
1 Coarse soil types include sand, loamy sand, or sandy loam .
2 Use only preemergence applications in conventional and reduced tillage systems .
3 Apply between corn emergence and the 5-leaf stage or 8-inches tall, whichever comes first . Use crop oil concentrate only in dry conditions when
corn is less than 5-inches tall and when applying BAS 183 36 H alone or tank mixed with atrazine .
4 Apply in corn that is 8-inches to 36-inches tall or up to 15 days before tassel emergence, whichever comes first .
NA - not applicable
Application Timing
Preplant (up to 14 days before planting)
and Preemergence Applications in
No Tillage Corn
BAS 183 36 H can be applied to emerged weeds before,
during, or after planting a corn crop . When planting into a
legume sod (e .g . alfalfa or clover), apply BAS 183 36 H
after 4 inches of regrowth . For application rates, refer to
Table 3 .
Preemergence Applications in
Conventional or Reduced Tillage Corn
BAS 183 36 H may be applied after planting and before
corn emergence; refer to Table 3 for application rates .
Preemergence application of BAS 183 36 H does not
require mechanical incorporation to become active . A
 shallow mechanical incorporation is recommended if the
application is not followed by adequate rainfall or sprinkler
irrigation . Avoid tillage equipment (e .g . drags, harrows) that
concentrates treated soil over seed furrow or seed dam-
age could result .
Postemergence Applications
(all tillage systems)
Apply early postemergence treatment between corn
 emergence and the 5-leaf stage or 8-inches tall, whichever
comes first . Apply later applications when corn is 8-inches
to 36-inches tall, or up to 15 days before tassel
 emergence, whichever comes first . Apply as a directed
spray when corn leaves prevent proper spray coverage .
Application rates vary by application timing; refer to
Table 3 for specific postemergence application rates .

17
Use with Other Herbicides
BAS 183 36 H herbicide may be applied sequentially
with one or more of, but not limited to, the following herbi-
cide products:
• Armezon® herbicide
• Armezon® PRO herbicide
• Outlook® herbicide
• Prowl® H2O herbicide
• Sharpen® powered by Kixor® herbicide
• Verdict® powered by Kixor® herbicide
• Zidua® herbicide
• atrazine
• glyphosate (e .g . Roundup® herbicide)
It is the pesticide user’s responsibility to ensure that all
products are registered for the intended use . Read and
follow the applicable restrictions and limitations and direc -
tions for use on all product labels involved in tank mixing .
Users must follow the most restrictive directions for use
and precautionary statements of each product in the tank
mixture .
NOTE: Refer to tank mix product labels to confirm the
respective tank mix products are registered for use on
specific corn types . Not all corn products are registered on
popcorn and seed corn .
Corn and Popcorn Restrictions
• DO NOT apply more than 12 .8 fl ozs/A (0 .5 pound
dicamba ae/A) in a single application of BAS 183 36 H .
• DO NOT apply more than a maximum cumulative total of
1 .5 pounds dicamba ae/A from all product sources per
year .
• DO NOT make more than three applications per year,
based on planting/growth stage .
• Allow a minimum of 7 days between applications .
• Corn or popcorn forage and silage may be harvested,
fed, or grazed when the crop has reached the ensilage
(milk) stage or later in maturity .
• BAS 183 36 H is not registered for use on sweet
corn.
Cotton
Before planting cotton, BAS 183 36 H may be used early
 preplant for burndown of actively growing broadleaf
weeds; refer to Table 1 for weeds controlled or
 suppressed .
Cotton gin byproducts may be fed to livestock .
Application Rates and Timings
Apply BAS 183 36 H as a broadcast spray up to 6 .4 fl
ozs/A plus specified adjuvants; refer to Tank Mixing
 Information section for details . For best performance,
apply BAS 183 36 H when weeds are less than 4 inches
in height and rosettes are less than 2-inches across .
Following application of BAS 183 36 H , wait until an accu-
mulation of 1 inch of rainfall or irrigation followed by an
interval of 21 days per 6 .4 fl ozs/A or less before planting
cotton . This interval must be observed before planting cot-
ton or severe crop injury may occur .
Missouri and Tennessee Only. Following application of
BAS 183 36 H , wait until an accumulation of 1 inch of rain -
fall or irrigation followed by an interval of 14 days per
6 .4 fl ozs/A or less before planting cotton . This interval
must be observed before planting cotton or severe crop
injury may occur .
Use with Other Herbicides
Broad-spectrum postemergence control of grass weeds or
additional broadleaf weeds requires another herbicide
such as glyphosate . BAS 183 36 H may be tank mixed or
applied sequentially with one or more of, but not limited to,
the following herbicide products:
• Sharpen
• glyphosate (e .g . Roundup)
It is the pesticide user’s responsibility to ensure that all
products are registered for the intended use . Read and
follow the applicable restrictions and limitations and direc -
tions for use on all product labels involved in tank mixing .
Users must follow the most restrictive directions for use
and precautionary statements of each product in the tank
mixture .
Cotton Restrictions
• DO NOT apply to dicamba tolerant (DT) cotton .
• DO NOT apply more than 6 .4 fl ozs/A (0 .25 pound
 dicamba ae/A) of BAS 183 36 H per year (single growing
 season) .
• DO NOT make more than one application per year .
• DO NOT apply preplant to cotton west of Interstate 25 .
• DO NOT make BAS 183 36 H preplant application to
cotton in geographic areas with average annual rainfall
less than 25 inches .
• DO NOT apply more than 2 .0 pounds dicamba acid
equivalent per acre for the combination of treatments if
applying a spring preplant treatment following application
of a fall preplant (postharvest) treatment .
Grass Grown for Seed
BAS 183 36 H may be used to control annual and peren-
nial broadleaf weeds after weed emergence . For best
performance, apply BAS 183 36 H when weeds are less
than 4 inches in height and rosettes are less than 2-inches
across . Apply BAS 183 36 H at 6 .4 to 12 .8 fl ozs/A plus
specified adjuvants to seedling grasses after the crop
reaches 3-leaf to 5-leaf stage; see Tank Mixing
 Information section for details . Apply up to 25 .6 fl ozs/A
of BAS 183 36 H on well-established perennial grasses .
Use the higher rate of the listed rate range when treating
more mature weeds or dense vegetative growth .

18
Use with Other Herbicides
BAS 183 36 H herbicide may be applied sequentially
with one or more of, but not limited to, the following herbi-
cide products:
• Facet® L herbicide
• Prowl® H2O herbicide
It is the pesticide user’s responsibility to ensure that all
products are registered for the intended use . Read and
follow the applicable restrictions and limitations and direc -
tions for use on all product labels involved in tank mixing .
Users must follow the most restrictive directions for use
and precautionary statements of each product in the tank
mixture .
Grass Grown for Seed Restrictions
• DO NOT apply BAS 183 36 H after grass seed crop
begins to joint .
• DO NOT apply more than 25 .6 fl ozs/A of BAS 183 36 H
(1 .0 pound dicamba ae/A) per application or a cumulative
total of 51 .2 fl ozs/A of BAS 183 36 H (2 pounds
 dicamba ae/A) per year .
• DO NOT apply more than eight times per year with a
minimum of 7 days between applications .
• Refer to Table 4 for grazing restrictions .
Pasture, Hay, Rangeland, and
Farmstead (noncropland)
BAS 183 36 H may be used on pasture, hay, rangeland,
and farmstead including fencerows and nonirrigation ditch -
banks for control or suppression of broadleaf weed and
woody brush and vine species listed in Table 1.
BAS 183 36 H uses described in this section also refer to
small grain grown for forage pasture use (rye, sorghum,
sudangrass, or wheat) . Grazing and harvest intervals are
shown in Table 4 .
 BAS 183 36 H may also be applied to noncropland areas
to control broadleaf weeds in noxious weed control pro-
grams, districts, or areas including broadcast or spot
treatment of roadsides, highways, utilities, railroad, and
pipeline rights-of-way . Noxious weeds must be recognized
at the state level, but programs may be administered at
state, county, or other level .
Application Rates and Timings
Refer to Table 2 for rate selection based on targeted weed
or brush species . Some weed species will require a tank
mix partner for adequate control . Retreatments may be
applied as needed .
• DO NOT broadcast spray apply more than 25 .6 fl ozs/A
of BAS 183 36 H (1 .0 pound dicamba ae/A) per year .
• DO NOT spot apply more than 51 .2 fl ozs/A of
BAS 183 36 H (2 .0 pounds dicamba ae/A) .
• DO NOT apply more than 12 .8 fl ozs/A of BAS 183 36 H
(0 .5 pound dicamba ae/A) per year on small grain grown
for pasture and newly seeded areas .
Established grass crops growing under stress can exhibit
various injury symptoms that may be more pronounced if
herbicides are applied . Bentgrass, buffalograss, carpet-
grass, and St . Augustinegrass may show a response .
Usually, colonial bentgrasses are more tolerant than creep -
ing types . Velvetgrasses are most easily injured .
Treatments will injure or kill alfalfa, clovers, lespedeza, wild
winter peas, vetch, and other legumes .
Spray volume may range from 10 to 600 gallons per acre .
The volume of spray applied depends on the height, densi -
ty, and type of weeds or brush being treated and on the
type of equipment used . BAS 183 36 H may be applied as
a spot treatment to individual clumps or small areas of
undesirable vegetation using a handgun or similar type of
application equipment . Apply diluted sprays to allow com-
plete wetting (up to runoff) of foliage and stems .
Table 4. Grazing and Haying Restrictions for
 Lactating Dairy Animals after BAS 183 36 H
Treatment
BAS 183 36 H
Rate
(fl ozs/A)
Days before
Grazing
Days before
Hay Harvest
Up to 12 .8 7 37
Up to 25 .6 21 51
Up to 51 .2 40 70
Cut-surface Treatment
BAS 183 36 H may be applied as a cut-surface treatment
for control of unwanted trees and prevention of sprouts of
cut trees . Mix 1 part BAS 183 36 H with 1 to 3 parts water
to create the application solution . Use the lower dilution
rate when treating difficult-to-control species .
• Frill or Girdle Treatment - Using an axe to girdle tree
trunk, make a continuous cut or a series of overlapping
cuts . Spray or paint the cut surface with the solution .
• Stump Treatment - Spray or paint freshly cut surface
with the water mix . Thoroughly wet the area adjacent to
the bark .
Dormant Multiflora Rose Applications
BAS 183 36 H can be applied as an undiluted spot treat-
ment directly to the soil or as a Lo-Oil basal bark treatment
using an oil-in-water emulsion solution when plants are
 dormant .
Spot Treatment Applications
Spot treatment application of BAS 183 36 H should be
applied directly to the soil as close as possible to the root
crown within 6 inches to 8 inches of the crown . On sloping
terrain, apply BAS 183 36 H to the uphill side of the
crown . DO NOT apply when snow or water prevents
applying BAS 183 36 H directly to the soil . The use rate of
BAS 183 36 H depends on the canopy diameter of the
multiflora rose .

19
Example BAS 183 36 H herbicide use rates:
• 0 .25 fl oz per 5-feet canopy diameter
• 1 .0 fl oz per 10-feet canopy diameter
• 2 .35 fl ozs per 15-feet canopy diameter
Lo-Oil Basal Bark Treatment
For Lo-Oil basal bark treatments, apply BAS 183 36 H to
the basal stem region from the ground line to a height of
12 inches to 18 inches . Spray until runoff, with special
emphasis on covering the root crown . For best results,
apply BAS 183 36 H when plants are dormant .
• DO NOT apply after bud break or when plants are
showing signs of active growth .
• DO NOT apply when snow or water prevents applying
BAS 183 36 H to the ground line .
Lo-Oil Spray Solution Preparation
1 . Combine 1 .5 gallons of water, 1 oz of emulsifier,
12 .8 fl ozs of BAS 183 36 H , and 2 .5 pints of No . 2 die-
sel fuel .
2 . Adjust the amounts of materials used proportionately to
the amount of final spray solution desired .
DO NOT apply more than 8 gallons/A of Lo-Oil spray solu-
tion mix per year .
Use with Other Herbicides
Broad-spectrum control of broadleaf and grass weeds
requires another herbicide . BAS 183 36 H may be applied
sequentially with one or more herbicide products:
It is the pesticide user’s responsibility to ensure that all
products are registered for the intended use . Read and
follow the applicable restrictions and limitations and direc -
tions for use on all product labels involved in tank mixing .
Users must follow the most restrictive directions for use
and precautionary statements of each product in the tank
mixture .
Pasture, Hay, Rangeland, and
Farmstead (noncropland) Restrictions
• DO NOT broadcast spray apply more than a maximum
cumulative total of 25 .6 fl ozs/A of BAS 183 36 H
(1 pound dicamba ae/A) per year .
• DO NOT spot apply more than 51 .2 fl ozs/A of
BAS 183 36 H (2 .0 pounds dicamba ae/A) .
• Allow a minimum of 7 days between applications .
• DO NOT apply more than a maximum cumulative total of
12 .8 fl ozs/A of BAS 183 36 H (0 .5 pound dicamba ae/A)
to small grain grown for pasture and to newly seeded
areas .
Proso Millet
For use only within Colorado, Nebraska,
North Dakota, South Dakota, and Wyoming
Apply BAS 183 36 H and 2,4-D sequentially to provide
control or suppression of annual broadleaf weeds; see
Table 1 .
Apply 3 .2 fl ozs/A of BAS 183 36 H sequentially with
0 .375 pound acid equivalent of 2,4-D per acre . Apply as a
broadcast or spot treatment to emerged and actively
growing weeds and when proso millet is in the 2-leaf to
5-leaf stage . Use directions for 2,4-D products vary with
manufacturers; refer to a 2,4-D product with labeling con-
sistent with the crop-stage timing for BAS 183 36 H .
Some types of proso millet may be affected adversely by a
sequential application of BAS 183 36 H and 2,4-D .
Proso Millet Restrictions
• DO NOT apply unless possible proso millet crop injury
will be acceptable .
• DO NOT apply more than 3 .2 fl ozs/A of BAS 183 36 H
(0 .125 pound dicamba ae/A) per year in proso millet .
• DO NOT apply more than 3 .2 fl ozs/A of BAS 183 36 H
(0 .25 pound dicamba ae/A) .
• DO NOT make more than one application per year .
• Refer to Table 4 for grazing restrictions .
Small Grain
(barley, oats, triticale, and wheat)
BAS 183 36 H may be applied before, during, or after plant-
ing small grain (barley, oats, triticale, and wheat) . Refer to
 Application Rates and Timings for specific small grain
crop uses . For best performance, apply BAS 183 36 H
when weeds are less than 4 inches in height and rosettes
are less than 2-inches across . Applying BAS 183 36 H to
small grain during periods of rapid growth may result in crop
leaning; this condition is temporary and will not reduce crop
yield .
Restrictions for small grain areas grazed or cut for hay are
indicated in Table 4 in Pasture, Hay, Rangeland, and
Farmstead (noncropland) section of this label .

20
Application Rates and Timings
Early Season Applications
Table 5. Early Season Application Rate and
Growth Stage in Small Grain 1
Crop
Fall-seeded Spring-seeded
Rate
(fl ozs/A)
Growth
Stage
Rate
(fl ozs/A)
Growth
Stage
(up to)
Barley2, 3
1 .6 to 3 .2 before
joint
1 .6 to 2 .4 4-leaf
Oats3 1 .6 to 3 .2 5-leaf
Triticale 1 .6 to 3 .2 6-leaf
Wheat4 1 .6 to 3 .2 6-leaf
1 An adjuvant system should be used with all BAS 183 36 H herbicide
applications; refer to Tank Mixing Information section for details .
DO NOT use oil concentrates for postemergence in-crop application .
2 For spring barley varieties seeded during winter months or later, follow
the rate and timing given for spring-seeded barley .
3 DO NOT tank mix BAS 183 36 H with 2,4-D in oats or early season
application on spring-seeded barley .
4 Early developing wheat varieties must receive application between early
tillering and the joint stage; ensure that the application occurs before
the jointing stage .
Fall-seeded Wheat ONLY
Western Oregon. When applied in the spring,
BAS 183 36 H may be used at rates up to 4 .8 fl ozs/A on
fall-seeded wheat . Periods of extended stress for example
cold and wet weather may enhance the possibility of crop
injury .
Colorado, Kansas, New Mexico, Oklahoma, and
Texas. For suppression of perennial weeds (for example
field bindweed), up to 6 .4 fl ozs/A of BAS 183 36 H may be
applied on fall-seeded wheat after wheat exceeds the 3-leaf
stage . Application may be made in the fall following a frost
but before a killing freeze . BAS 183 36 H at 6 .4 fl ozs/A may
be sequentially applied with MCPA after wheat begins to
tiller . Periods of extended stress for example cold and wet
weather may enhance the possibility of crop injury . For fall
applications only, DO NOT apply BAS 183 36 H if the
potential for crop injury is unacceptable .
Preharvest Applications
To control broadleaf weeds that interfere with harvest,
BAS 183 36 H may be applied before harvest when barley
or wheat is in the hard dough stage and the green color is
gone from the nodes (joints) of the stem . Best results will
be obtained if the application can be made when weeds
are actively growing but before weeds canopy .
BAS 183 36 H applications may be made to fall-planted
and spring-planted barley and wheat at 6 .4 fl ozs/A as a
 broadcast application or spot treatment . A preharvest
interval (PHI) of 7 days is required before crop harvest .
Use with Other Herbicides
Broad-spectrum control of broadleaf and grass weeds
requires another herbicide . BAS 183 36 H may be applied
sequentially with one or more of, but not limited to, the fol-
lowing herbicide products:
• Beyond® herbicide (for Clearfield ® wheat and
 Clearfield ® Plus wheat only)
• Clearmax® herbicide (for Clearfield wheat and
Clearfield Plus wheat only)
• Sharpen® powered by Kixor® herbicide
• Zidua® herbicide
• 2,4-D amine
• MCPA
• sulfonylurea-based herbicide (e .g . Ally® herbicide,
Express® herbicide, Finesse® herbicide)
It is the pesticide user’s responsibility to ensure that all
products are registered for the intended use . Read and
follow the applicable restrictions and limitations and direc -
tions for use on all product labels involved in tank mixing .
Users must follow the most restrictive directions for use
and precautionary statements of each product in the tank
mixture .
Small Grain Restrictions
• Maximum use rate per application
- 3 .2 fl ozs/A (0 .125 pound dicamba ae/A): Oats and
triticale
- 6 .4 fl ozs/A (0 .25 pound dicamba ae/A): Spring-seeded
barley, fall-seeded barley, wheat
• Maximum annual use rate
- 3 .2 fl ozs/A (0 .125 pound dicamba ae/A): Oats and
triticale
- 8 .8 fl ozs/A (0 .34 pound dicamba ae/A): Spring-seeded
barley
- 9 .6 fl ozs/A (0 .375 pound dicamba ae/A): Fall-seeded
barley
- 12 .8 fl ozs/A (0 .5 pound dicamba ae/A): Wheat
• DO NOT apply BAS 183 36 H preharvest to oats or
 triticale .
• DO NOT use an oil concentrate adjuvant for postemer-
gence in-crop application .
• DO NOT use preharvest-treated barley or wheat for
seed unless a germination test with an acceptable result
of 95% germination or more is performed on the seed .
• DO NOT graze small grain (barley, oats, triticale, wheat)
within 7 days after treatment .
• DO NOT harvest for hay within 37 days after treatment .
• Barley and wheat may be harvested 7 days or more after
a preharvest application .
• DO NOT make preharvest application in California .
Sorghum
BAS 183 36 H may be used early preplant, postemer-
gence, and preharvest in sorghum to control many annual
broadleaf weeds and to reduce competition from estab -
lished perennial broadleaf weeds .

21
Application Rates and Timings
Preplant Applications
(at least 14 days before planting)
A preplant application of BAS 183 36 H herbicide up to
6 .4 fl ozs/A may be applied at least 14 days before sor -
ghum planting .
Postemergence Applications
Up to 6 .4 fl ozs/A of BAS 183 36 H plus specified adju-
vants (refer to Tank Mixing Information section for
details) may be applied after sorghum is in the spike stage
(all sorghum emerged) but before sorghum is 15-inches
tall . For best performance, apply BAS 183 36 H when sor-
ghum crop is in the 3-leaf to 5-leaf stage and weeds are
small (less than 3-inches tall) . Use drop nozzles if sorghum
is taller than 8 inches . Keep spray off sorghum leaves and
out of the whorl to reduce the like lihood of crop injury and
to improve spray coverage of weed foliage .
Applying BAS 183 36 H to sorghum during periods of
rapid growth may result in temporary leaning of plants or
rolling of leaves . These effects are usually outgrown within
10 to 14 days .
Preharvest Applications
Oklahoma and Texas ONLY
Up to 6 .4 fl ozs/A of BAS 183 36 H may be applied for
weed suppression any time after sorghum has reached the
 soft-dough stage . An agriculturally approved surfactant
may be used to improve performance; see Tank Mixing
 Information section for details . Delay harvest until
30 days after a preharvest treatment .
Split Applications
BAS 183 36 H may be applied in split applications: pre-
plant followed by postemergence or preharvest; or
postemergence followed by preharvest . DO NOT apply
more than 6 .4 fl ozs/A of BAS 183 36 H (0 .25 pound
 dicamba ae/A) per application, or a maximum cumulative
total of 12 .8 fl ozs/A of BAS 183 36 H (0 .5 pound
 dicamba ae/A) per year .
Use with Other Herbicides
BAS 183 36 H may be applied sequentially with one or
more of, but not limited to, the following herbicide
products:
• Basagran® 5L herbicide
• Facet® L herbicide
• Outlook® herbicide - (Preplant only)
• Sharpen® powered by Kixor® herbicide
• Verdict® powered by Kixor® herbicide
• atrazine
• glyphosate (e .g . Roundup® herbicide)
It is the pesticide user’s responsibility to ensure that all
products are registered for the intended use . Read and
follow the applicable restrictions and limitations and direc -
tions for use on all product labels involved in tank mixing .
Users must follow the most restrictive directions for use
and precautionary statements of each product in the tank
mixture .
Sorghum Restrictions
• DO NOT graze or feed treated sorghum forage or silage
before mature grain stage . If sorghum is grown for pas-
ture or hay, refer to Pasture, Hay, Rangeland, and
Farmstead (noncropland) section for specific grazing
and feeding restrictions .
• DO NOT apply BAS 183 36 H to sorghum grown for
seed production .
• DO NOT apply more than 6 .4 fl ozs/A of BAS 183 36 H
(0 .25 pound dicamba ae/A) per application .
• DO NOT apply more than a maximum cumulative total of
12 .8 fl ozs/A of BAS 183 36 H (0 .5 pound dicamba ae/A)
per year .
• DO NOT apply more than two times per year with a min -
imum of 7 days between applications .
• Oklahoma and Texas only - Delay harvest until
30 days after a preharvest treatment .
Soybean
 BAS 183 36 H may be used preplant or preharvest in soy-
bean to control many annual broadleaf weeds and to
reduce competition from established biennial and perenni -
al broadleaf weeds .
Application Rates and Timings
Preplant Applications
(at least 14 days before planting)
Apply BAS 183 36 H as a broadcast spray at 3 .2 to
25 .6 fl ozs/A plus specified adjuvants; refer to Tank
 Mixing Information section for details .
 Preplant Intervals. Following application of
BAS 183 36 H and a minimum accumulation of 1 inch of
rainfall or overhead irrigation, preplant waiting intervals are
required before planting soybeans or crop injury may
occur:
• 14 days for 3 .2 to 6 .4 fl ozs/A
• 28 days for 6 .5 to 12 .8 fl ozs/A
Preharvest Applications
Apply BAS 183 36 H as a broadcast spray or spot spray
at 6 .4 to 25 .6 fl ozs/A plus specified adjuvants; refer to
Tank Mixing Information section for details . Applications
should be made to emerged and actively growing weeds
after soybean pods have reached mature brown color and
at least 75% leaf drop has occurred .
Treatments may not kill weeds that later develop from seed
or underground parts, including rhizomes or bulblets, after
the effective residual period for BAS 183 36 H . For seed-
ling control, a follow-up program or other cultural practices
should be instituted .

22
Use with Other Herbicides
BAS 183 36 H herbicide may be applied sequentially
with one or more of, but not limited to, the following herbi-
cide products:
• Outlook® herbicide
• Prowl® H2O herbicide
• Pursuit® herbicide
• Raptor® herbicide
• Sharpen® powered by Kixor® herbicide
• Verdict® powered by Kixor® herbicide
• Zidua® herbicide
• Zidua® PRO powered by Kixor® herbicide
• glyphosate (e .g . Roundup® herbicide)
It is the pesticide user’s responsibility to ensure that all prod-
ucts are registered for the intended use . Read and follow
the applicable restrictions and limitations and directions for
use on all product labels involved in tank mixing . Users must
follow the most restrictive directions for use and precaution-
ary statements of each product in the tank mixture .
Soybean Restrictions
• DO NOT apply to dicamba tolerant (DT) soybeans .
• DO NOT apply more than 12 .8 fl ozs/A of BAS 183 36 H
(0 .5 pound dicamba ae/A) in a spring application before
soybean planting .
• DO NOT make BAS 183 36 H preplant application to
soybeans in geographic areas with average annual rain -
fall less than 25 inches .
• DO NOT apply more than 25 .6 fl ozs/A of BAS 183 36 H
(1 pound dicamba ae/A) per year (single growing season) .
• DO NOT make more than two applications per year .
• DO NOT use preharvest-treated soybean for seed
unless a germination test with an acceptable result of
95% germination or better is performed on the seed .
• DO NOT harvest soybeans until 7 days after a prehar-
vest application .
• DO NOT feed soybean fodder or hay following prehar-
vest application of BAS 183 36 H .
• DO NOT make preharvest applications in California .
Sugarcane
BAS 183 36 H may be used any time after weed emer-
gence but before the close-in stage of sugarcane to
control many annual and perennial broadleaf weeds; see
Table 1 for weeds controlled or suppressed .
Apply 6 .4 to 12 .8 fl ozs/A of BAS 183 36 H for control of
annual weeds and 12 .8 to 25 .6 fl ozs/A for control or sup-
pression of biennial and perennial weeds . Use the higher
rate of the specified rate range when treating dense vege-
tative growth . Repeat treatment may be made as needed;
however, DO NOT apply more than the annual maximum
cumulative total of 51 .2 fl ozs/A of BAS 183 36 H
(2 pounds dicamba ae/A) .
When possible, direct the spray beneath the sugarcane
canopy to minimize the likelihood of crop injury . Using
directed sprays will also help maximize the spray coverage
of weed foliage .
Use with Other Herbicides
BAS 183 36 H may be applied sequentially with one or
more of, but not limited to, the following herbicide
products:
• Prowl H2O
• atrazine
It is the pesticide user’s responsibility to ensure that all prod-
ucts are registered for the intended use . Read and follow
the applicable restrictions and limitations and directions for
use on all product labels involved in tank mixing . Users must
follow the most restrictive directions for use and precaution-
ary statements of each product in the tank mixture .
Sugarcane Restrictions
• DO NOT apply more than 25 .6 fl ozs/A of BAS 183 36 H
(1 .0 pound dicamba ae/A) in a single application .
• Allow a minimum of 7 days between applications .
• DO NOT apply more than a maximum cumulative total of
51 .2 fl ozs/A of BAS 183 36 H (2 pounds dicamba ae/A)
per year .
• DO NOT harvest sugarcane until 87 days after application .
Farmstead Turf (noncropland)
and Sod Farms
BAS 183 36 H may be used in farmstead turf (noncrop-
land) and sod farms to control or suppress growth of many
annual, biennial, and some perennial broadleaf weeds; see
Table 1 for weeds controlled or suppressed .
BAS 183 36 H will also suppress woody brush and vine
species; refer to Table 2 for application rates based on
 targeted weed or woody brush and vine species and
growth stage . Some weed species will require tank mixes
for optimum control .
Repeat treatment may be made as needed; however,
DO NOT apply more than 25 .6 fl ozs/A of BAS 183 36 H
(1 pound dicamba ae/A) per year .
Apply 30 to 200 gallons of diluted spray per acre (3 to
17 quarts of water per 1000 sq ft), depending on density
or height of weeds treated and on type of equipment used .
To avoid injury to newly seeded grasses, delay application
of BAS 183 36 H until after the second mowing . Estab-
lished grass crops growing under stress can exhibit
various injury symptoms that may be more pronounced if
herbicides are applied . Bentgrass, buffalograss, carpet-
grass, and St . Augustinegrass may show a response .

23
Use with Other Herbicides
BAS 183 36 H herbicide at 3 .2 to 12 .8 fl ozs/A may be
applied sequentially with one or more of, but not limited to,
the following herbicide products:
• Drive® XLR8 herbicide
• Pendulum® AquaCap herbicide
• Tower® herbicide
• 2,4-D
• MCPA
• MCPP
It is the pesticide user’s responsibility to ensure that all prod-
ucts are registered for the intended use . Read and follow
the applicable restrictions and limitations and directions for
use on all product labels involved in tank mixing . Users must
follow the most restrictive directions for use and precaution-
ary statements of each product in the tank mixture .
Farmstead Turf and Sod Farm Restrictions
• DO NOT use on residential sites .
• DO NOT apply more than 25 .6 fl ozs/A of BAS 183 36 H
(1 pound dicamba ae/A) per year .
• Areas where Roots of Sensitive Plants Extend
- DO NOT apply more than 3 .2 fl ozs/A of BAS 183 36 H
(0 .125 pound dicamba ae/A) on coarse-texture soils
(sand, loamy sand, or sandy loam) .
- DO NOT apply more than 6 .4 fl ozs/A of BAS 183 36 H
(0 .25 pound dicamba ae/A) on fine-texture soils .
- DO NOT make repeat applications in these areas for
30 days and until previous applications of
BAS 183 36 H have been activated in the soil by rainfall
or irrigation .

24
Conditions of Sale and Warranty
The Directions For Use of this product reflect the
 opinion of experts based on field use and tests . The
 directions are believed to be reliable and must be
followed carefully . However, it is impossible to eliminate
all risks inherently associated with the use of this
product . Crop injury, ineffectiveness or other unintended
consequences may result because of such factors as
weather conditions, presence of other materials, or use
of the product in a manner inconsistent with its labeling,
all of which are beyond the control of BASF
CORPORATION (“BASF”) or the Seller . To the extent
consistent with applicable law, all such risks shall be
assumed by the Buyer .
BASF warrants that this product conforms to the
chemical description on the label and is reasonably fit for
the purposes referred to in the Directions For Use ,
subject to the inherent risks, referred to above .
TO THE EXTENT CONSISTENT WITH APPLICABLE
LAW, BASF MAKES NO OTHER EXPRESS OR
IMPLIED WARRANTY OF FITNESS OR
 MERCHANTABILITY OR ANY OTHER EXPRESS OR
IMPLIED WARRANTY.
TO THE EXTENT CONSISTENT WITH APPLICABLE
LAW, BUYER’S EXCLUSIVE REMEDY AND BASF’S
EXCLUSIVE LIABILITY, WHETHER IN CONTRACT,
TORT, NEGLIGENCE, STRICT LIABILITY, OR
 OTHERWISE, SHALL BE LIMITED TO REPAYMENT
OF THE PURCHASE PRICE OF THE PRODUCT.
TO THE EXTENT CONSISTENT WITH APPLICABLE
LAW, BASF AND THE SELLER DISCLAIM ANY
 LIABILITY FOR CONSEQUENTIAL, EXEMPLARY,
SPECIAL OR INDIRECT DAMAGES RESULTING
FROM THE USE OR HANDLING OF THIS
PRODUCT.
BASF and the Seller offer this product, and the Buyer
and User accept it, subject to the foregoing Conditions
of Sale and Warranty which may be varied only by
 agreement in writing signed by a duly authorized
representative of BASF . 1108
Referenced Pesticides (Name, Reg . No ., Active)
Ally® herbicide, 279-9575, Metsulfuron Methyl
Armezon® herbicide, 7969-262, Topramezone
Armezon® PRO herbicide, 7969-372, Topramezone,
Dimethenamid
Basagran® 5L herbicide, 7969-112, Bentazon
Beyond® herbicide, 7969-441, Imazamox
Clearmax® herbicide, 7969-238, Imazamox, MCPA
Distinct ® herbicide, 7969-150, Dicamba, Diflufenzopyr
Drive® XLR8 herbicide, 7969-272, Quinclorac
Express® herbicide, 279-9578, Tribenuron Methyl
Facet® L herbicide, 7969-315, Quinclorac
Finesse® herbicide, 279-9576, Chlorsulfuron,
Metsulfuron Mehtyl
Gramoxone® SL herbicide, 100-1652, Paraquat
Lorsban® insecticide, 62719-34, Chlorpyrifos
Outlook® herbicide, 7969-156, Dimethenamid
Pendulum® AquaCap (add to page 23?) herbicide ,
241-416, Pendimethalin
Prowl® H2O herbicide, 241-418, Pendimethalin
Pursuit® herbicide, 241-310, Imazethapyr
Raptor® herbicide, 241-379, Imazamox
Roundup® herbicide, 524-549, Glyphosate
Select Max® herbicide, 59639-132, Clethodim
Sharpen® powered by Kixor® herbicide, 7969-278,
Saflufenacil
Tower® herbicide, 7969-239, Dimethenamid
Varisto® herbicide, 241-447 , Bentazon/Imazamox
Verdict® powered by Kixor® herbicide, 7969-279,
Dimethenamid/Saflufenacil
Zidua® herbicide, 7969-338, Pyroxasulfone
Zidua® PRO powered by Kixor® herbicide, 7969-365,
Saflufenacil/Pyroxasulfone
© 2022 BASF Corporation
All rights reserved .
007969-00XXX .20210727e .NVA 2021-04-667-0138
BASF Corporation
26 Davis Drive
Research Triangle Park, NC 27709
Armezon, Basagran, Beyond, Clearfield , Clearmax,
Distinct, Drive, Facet, Kixor, Outlook, Pendulum,
Prowl, Pursuit, Raptor, Sharpen, Tower, Varisto,
Verdict, and Zidua are registered trademarks of BASF.
Ally, Express, and Finesse are registered trademarks of
DuPont Crop Protection.
Gramoxone is a registered trademark of a Syngenta
Group Company.
Lorsban is a registered trademark of Dow AgroSciences
LLC.
Roundup is a registered trademark of Monsanto
Technology LLC.
Select Max is a registered trademark of Valent U.S.A.
Corporation.