1489 lines
62 KiB
Markdown
1489 lines
62 KiB
Markdown
# INDAR 75 WSP
|
||
|
||
- EPA Reg No: **62719-421**
|
||
- Registrant: CORTEVA AGRISCIENCE, LLC
|
||
- Signal word: Caution
|
||
- Active ingredients: Fenbuconazole (75%)
|
||
- Label accepted: 2026-09-21
|
||
- Source PDF: https://www3.epa.gov/pesticides/chem_search/ppls/062719-00421-20260921.pdf
|
||
|
||
---
|
||
September 21, 2026
|
||
|
||
Tamara Lunsman, Ph.D.
|
||
Principal Investigator, US Regulatory Leader
|
||
Corteva Agriscience LLC
|
||
9330 Zionsville Road
|
||
Indianapolis, Indiana 46268
|
||
tamara.lunsman@corteva.com
|
||
|
||
Subject: Label Amendment - Registrati on Review Mitigation for Fenbuconazole
|
||
Product Name: Indar 75WSP
|
||
EPA Registration Number: 62719-421
|
||
Case Number: 473381
|
||
Application Dates: March 31, 2022
|
||
|
||
Dear Tamara Lunsman:
|
||
|
||
The Agency, in accordance with the Federal Insecticide, Fungicide, and Rodenticide Act (FIFRA),
|
||
as amended, has completed reviewing all the information submitted with your application to
|
||
support the Registration Review of the above referenced product in connection with the
|
||
Fenbuconazole Interim Decision, and has concluded that your submission is acceptable. The
|
||
label referred to above, submitted in connection with registration under FIFRA, as amended, is
|
||
acceptable.
|
||
|
||
Should you wish to add/retain a reference to the company’s website on your label, then please
|
||
be aware that the website becomes labeling under the Federal Insecticide, Fungicide, and
|
||
Rodenticide Act and is subject to review by the Agency. If the website is false or misleading, the
|
||
product would be misbranded and unlawful to sell or distribute under FIFRA section 12(a)(1)(E).
|
||
40 CFR 156.10(a)(5) list examples of statements EPA may consider false or misleading. In
|
||
addition, regardless of whether a website is referenced on your product’s label, claims made on
|
||
the website may not substantially differ from those claims approved through the registration
|
||
process. Therefore, should the Agency find or if it is brought to our attention that a website
|
||
contains false or misleading statements or claims substantially differing from the EPA approved
|
||
registration, the website will be referred to the EPA’s Office of Enforcement and Compliance
|
||
Assurance.
|
||
|
||
A stamped copy of your labeling is enclosed for your records. This labeling supersedes
|
||
all previously accepted labeling and must be used at your next label printing. You must
|
||
|
||
Page 2 of 2
|
||
EPA Reg. No. 62719-421
|
||
Case No. 473381
|
||
|
||
submit one copy of the final printed labeling before you release the product for
|
||
shipment with the new labeling. In accordance with 40 CFR 152.130(c), you may
|
||
distribute or sell this product under the previously approved labeling for 12 months
|
||
from the date of this letter. After 12 months, you may only distribute or sell this
|
||
product if it bears this new revised labeling or subsequently approved labeling. “To
|
||
distribute or sell” is defined under FIFRA section 2(gg) and its implementing regulation
|
||
at 40 CFR 152.3.
|
||
|
||
If you have any questions about this letter, please contact Concepción Rodríguez by phone at
|
||
202-566-0820, or via email at rodriguez.concecpion@epa.gov.
|
||
|
||
S i n c e r e l y ,
|
||
|
||
|
||
Julie Javier, Team Leader
|
||
Risk Mitigation and Implementation Branch 4
|
||
Pesticide Re-Evaluation Division
|
||
Office of Pesticide Programs
|
||
|
||
ENCLOSURE: Stamped label
|
||
|
||
A3B / Indar 75WSP / MSTR / Amend / 09-03-2026 Page 1
|
||
(Bulk/Tote base label):
|
||
FENBUCONAZOLE GROUP G1 FUNGICIDE
|
||
Indar® 75WSP
|
||
Fungicide
|
||
Active Ingredient
|
||
fenbuconazole: a-[2-(4-chlorophenyl)ethyl]-
|
||
a-phenyl-1H-1,2,4-triazole-1-propanenitrile . 75%
|
||
Other Ingredients ................................................... 25%
|
||
Total ..................................................................... 100%
|
||
Keep Out Of Reach Of Children
|
||
CAUTION
|
||
First Aid
|
||
If on skin or clothing: Take off contaminated clothing. Rinse skin immediately with plenty of water for
|
||
15-20 minutes. Call a poison control center or doctor for treatment advice.
|
||
If swallowed: Call a poison control center or doctor immediately for treatment advice. Have person sip a
|
||
glass of water if able to swallow. Do not induce vomiting unless told to do so by a poison control center
|
||
or doctor. Do not give anything by mouth to an unconscious person.
|
||
Have the product container or label with you when calling a poison control center or doctor, or going for
|
||
treatment. You may also contact 1-800-992-5994 day or night for emergency treatment information.
|
||
PRECAUTIONARY STATEMENTS
|
||
Hazards to Humans and Domestic Animals
|
||
CAUTION
|
||
Harmful If Swallowed Or Absorbed Through The Skin
|
||
Avoid contact with skin, eyes or clothing.
|
||
Personal Protective Equipment (PPE)
|
||
Applicators and other handlers must wear:
|
||
• Long-sleeved shirt and long pants
|
||
• Shoes plus socks
|
||
• Waterproof gloves
|
||
• Chemical-resistant headgear for overhead exposure
|
||
User Safety Requirements
|
||
Follow manufacturer's instructions for cleaning/maintaining PPE. If no such instructions for washables
|
||
exist, use detergent and hot water. Keep and wash PPE separately from other laundry.
|
||
Engineering Controls
|
||
Water soluble packets, when used correctly, qualify as a closed mixing/loading system under the worker
|
||
Protection Standard [40 CFR 170.607(d)]. Mixers and loaders handling this product while it is enclosed in
|
||
intact water soluble packets may elect to wear reduced PPE of long-sleeved shirt, long pants, shoes,
|
||
Sep 21, 2026
|
||
62719-421
|
||
|
||
A3B / Indar 75WSP / MSTR / Amend / 09-03-2026 Page 2
|
||
socks. When reduced PPE is worn because a closed system is being used, handlers must be provided all
|
||
PPE specified above for “applicators and other handlers” and have such PPE immediately available for
|
||
use in an emergency, such as a spill or equipment break-down.
|
||
|
||
User Safety Recommendations
|
||
Users should:
|
||
• Wash hands before eating, drinking, chewing gum, using tobacco or using the toilet.
|
||
• Remove clothing/PPE immediately if pesticides get inside. Then wash and put on clean clothing.
|
||
• Remove PPE immediately after handling product. Wash outside of gloves before removing. As soon
|
||
as possible, wash thoroughly and change into clean clothing.
|
||
|
||
Environmental Hazards
|
||
This product is toxic to fish. Do not apply directly to water, or to areas where surface water is present, or
|
||
to intertidal areas below the mean high-water mark. Drift or runoff from treated areas may be hazardous
|
||
to aquatic organisms in adjacent aquatic sites. Do not contaminate water when disposing of equipment
|
||
washwaters or rinsate.
|
||
|
||
Agricultural Use Requirements
|
||
Use this product only in accordance with its labeling and with the Worker Protection Standard, 40 CFR
|
||
Part 170. Refer to the label booklet under "Agricultural Use Requirements" in the Directions for Use
|
||
section for information about this standard.
|
||
|
||
(Storage and Disposal for rigid containers 5 gal or less)
|
||
Storage and Disposal
|
||
Do not contaminate water, food, or feed by storage or disposal.
|
||
Pesticide Storage: Store in a cool, dry area above freezing. If in a water-soluble pouch, the water-
|
||
soluble pouch may become brittle at storage temperatures below 32°F but the fungicide is not affected.
|
||
Do not remove the water-soluble pouches from container except for immediate use.
|
||
Pesticide Disposal: Wastes resulting from the use of this product may be disposed of on site or at an
|
||
approved waste disposal facility.
|
||
Container Handling: Nonrefillable container. Do not reuse or refill this container. Offer for recycling if
|
||
available.
|
||
Triple rinse or pressure rinse container (or equivalent) promptly after emptying. Triple rinse as follows:
|
||
Empty the remaining contents into application equipment or a mix tank and drain for 10 seconds after the
|
||
flow begins to drip. Fill the container 1/4 full with water and recap. Shake for 10 seconds. Pour rinsate
|
||
into application equipment or a mix tank or store rinsate for later use or disposal. Drain for 10 seconds
|
||
after the flow begins to drip. Repeat this procedure two more times. Pressure rinse as follows: Empty
|
||
the remaining contents into application equipment or a mix tank and continue to drain for 10 seconds after
|
||
the flow begins to drip. Hold container upside down over application equipment or mix tank or collect
|
||
rinsate for later use or disposal. Insert pressure rinsing nozzle in the side of the container, and rinse at
|
||
about 40 psi for at least 30 seconds. Drain for 10 seconds after the flow begins to drip. Then offer for
|
||
recycling if available. Or puncture and dispose of in a sanitary landfill, or by incineration, or by other
|
||
procedures allowed by state and local authorities.
|
||
|
||
(Storage and Disposal for nonrigid containers any size)
|
||
Storage and Disposal
|
||
Do not contaminate water, food, or feed by storage or disposal.
|
||
Pesticide Storage: Store in a cool, dry area above freezing. If in a water-soluble pouch, the water-
|
||
soluble pouch may become brittle at storage temperatures below 32°F but the fungicide is not affected.
|
||
Do not remove the water-soluble pouches from container except for immediate use.
|
||
Pesticide Disposal: Wastes resulting from the use of this product may be disposed of on site or at an
|
||
approved waste disposal facility.
|
||
Container Handling: Nonrefillable container. Do not reuse or refill this container. Offer for recycling if
|
||
available.
|
||
|
||
A3B / Indar 75WSP / MSTR / Amend / 09-03-2026 Page 3
|
||
|
||
(Storage and Disposal for refillable rigid containers greater than 5 gal)
|
||
Storage and Disposal
|
||
Do not contaminate water, food, or feed by storage or disposal.
|
||
Pesticide Storage: Store in a cool, dry area above freezing. If in a water-soluble pouch, the water-
|
||
soluble pouch may become brittle at storage temperatures below 32°F but the fungicide is not affected.
|
||
Do not remove the water-soluble pouches from container except for immediate use.
|
||
Pesticide Disposal: Wastes resulting from the use of this product may be disposed of on site or at an
|
||
approved waste disposal facility.
|
||
Container Handling: Refillable container. Refill this container with pesticide only. Do not reuse this
|
||
container for any other purpose.
|
||
Cleaning the container before final disposal is the responsibility of the person disposing of the container.
|
||
Cleaning before refilling is the responsibility of the refiller. To clean the container before final disposal,
|
||
empty the remaining contents from this container into application equipment or a mix tank. Fill the
|
||
container about 10% full with water and, if possible, spray all sides while adding water. If practical,
|
||
agitate vigorously or recirculate water with the pump for two minutes. Pour or pump rinsate into
|
||
application equipment or rinsate collection system. Repeat this rinsing procedure two more times. Then
|
||
offer for recycling if available. Or puncture and dispose of in a sanitary landfill, or by incineration, or if
|
||
allowed by state and local authorities, by burning. If burned, stay out of smoke.
|
||
|
||
(Storage and Disposal for nonrefillable rigid containers larger than 5 gal)
|
||
Storage and Disposal
|
||
Do not contaminate water, food, or feed by storage or disposal.
|
||
Pesticide Storage: Store in a cool, dry area above freezing. If in a water-soluble pouch, the water-
|
||
soluble pouch may become brittle at storage temperatures below 32°F but the fungicide is not affected.
|
||
Do not remove the water-soluble pouches from container except for immediate use.
|
||
Pesticide Disposal: Wastes resulting from the use of this product may be disposed of on site or at an
|
||
approved waste disposal facility.
|
||
Container Handling: Nonrefillable container. Do not reuse or refill this container. Offer for recycling if
|
||
available.
|
||
Triple rinse or pressure rinse container (or equivalent) promptly after emptying. Triple rinse as follows:
|
||
Empty the remaining contents into application equipment or a mix tank. Fill the container 1/4 full with
|
||
water. Replace and tighten closures. Tip container on its side and roll it back and forth, ensuring at least
|
||
one complete revolution, for 30 seconds. Stand the container on its end and tip it back and forth several
|
||
times. Turn the container over onto its other end and tip it back and forth several times. Empty the
|
||
rinsate into application equipment or a mix tank or store rinsate for later use or disposal. Repeat this
|
||
procedure two more times. Pressure rinse as follows: Empty the remaining contents into application
|
||
equipment or a mix tank and continue to drain for 10 seconds after the flow begins to drip. Hold container
|
||
upside down over application equipment or mix tank or collect rinsate for later use or disposal. Insert
|
||
pressure rinsing nozzle in the side of the container, and rinse at about 40 psi for at least 30 seconds.
|
||
Drain for 10 seconds after the flow begins to drip. Then offer for recycling if available. Or puncture and
|
||
dispose of in a sanitary landfill, or by incineration, or if allowed by state and local authorities, by burning.
|
||
If burned, stay out of smoke.
|
||
|
||
Refer to label booklet for additional precautionary information and Directions for Use.
|
||
|
||
Notice: Read the entire label. Use only according to label directions. Before using this product, read
|
||
Warranty Disclaimer, Inherent Risks of Use, and Limitation of Remedies at end of label booklet. If
|
||
terms are unacceptable, return at once unopened.
|
||
|
||
In case of emergency endangering health or the environment involving this product, call 1-800-992-5994.
|
||
|
||
Agricultural Chemical: Do not ship or store with food, feeds, drugs or clothing.
|
||
|
||
EPA Reg. No. 62719-421 EPA Est. _______
|
||
|
||
A3B / Indar 75WSP / MSTR / Amend / 09-03-2026 Page 4
|
||
|
||
™®Trademarks of Corteva Agriscience and its affiliated companies
|
||
|
||
Produced for
|
||
Corteva Agriscience LLC
|
||
9330 Zionsville Road
|
||
Indianapolis, IN 46268
|
||
Net Weight _____
|
||
|
||
A3B / Indar 75WSP / MSTR / Amend / 09-03-2026 Page 5
|
||
(shipping / small container base label):
|
||
|
||
FENBUCONAZOLE GROUP G1 FUNGICIDE
|
||
|
||
Indar® 75WSP
|
||
|
||
Fungicide
|
||
|
||
Active Ingredient
|
||
fenbuconazole: a-[2-(4-chlorophenyl)ethyl]-
|
||
a-phenyl-1H-1,2,4-triazole-1-propanenitrile . 75%
|
||
Other Ingredients ................................................... 25%
|
||
Total ..................................................................... 100%
|
||
|
||
Keep Out Of Reach Of Children
|
||
CAUTION
|
||
|
||
First Aid
|
||
If on skin or clothing: Take off contaminated clothing. Rinse skin immediately with plenty of water for
|
||
15-20 minutes. Call a poison control center or doctor for treatment advice.
|
||
If swallowed: Call a poison control center or doctor immediately for treatment advice. Have person sip a
|
||
glass of water if able to swallow. Do not induce vomiting unless told to do so by a poison control center
|
||
or doctor. Do not give anything by mouth to an unconscious person.
|
||
|
||
Have the product container or label with you when calling a poison control center or doctor, or going for
|
||
treatment. You may also contact 1-800-992-5994 day or night, for emergency treatment information.
|
||
|
||
Agricultural Use Requirements
|
||
Use this product only in accordance with its labeling and with the Worker Protection Standard, 40 CFR
|
||
Part 170. Refer to the label booklet under "Agricultural Use Requirements" in the Directions for Use
|
||
section for information about this standard.
|
||
|
||
Refer to inside of label booklet for additional precautionary information including Directions for
|
||
Use.
|
||
|
||
Notice: Read the entire label. Use only according to label directions. Before using this product, read
|
||
Warranty Disclaimer, Inherent Risks of Use, and Limitation of Remedies at end of label booklet. If
|
||
terms are unacceptable, return at once unopened.
|
||
|
||
In case of emergency endangering health or the environment involving this product, call 1-800-992-5994.
|
||
|
||
Agricultural Chemical: Do not ship or store with food, feeds, drugs or clothing.
|
||
|
||
EPA Reg. No. 62719-421 EPA Est. _______
|
||
|
||
™
|
||
®Trademarks of Corteva Agriscience and its affiliated companies
|
||
|
||
Produced for
|
||
Corteva Agriscience LLC
|
||
9330 Zionsville Road
|
||
Indianapolis, IN 46268
|
||
Net Weight _____
|
||
|
||
A3B / Indar 75WSP / MSTR / Amend / 09-03-2026 Page 6
|
||
(Page 1 through end):
|
||
|
||
PRECAUTIONARY STATEMENTS
|
||
Hazards to Humans and Domestic Animals
|
||
CAUTION
|
||
|
||
Harmful If Swallowed Or Absorbed Through The Skin
|
||
|
||
Avoid contact with skin, eyes or clothing.
|
||
|
||
Personal Protective Equipment (PPE)
|
||
|
||
Applicators and other handlers must wear:
|
||
• Long-sleeved shirt and long pants
|
||
• Shoes plus socks
|
||
• Waterproof gloves
|
||
• Chemical-resistant headgear for overhead exposure
|
||
|
||
User Safety Requirements
|
||
Follow manufacturer's instructions for cleaning/maintaining PPE. If no such instructions for washables
|
||
exist, use detergent and hot water. Keep and wash PPE separately from other laundry.
|
||
|
||
Engineering Controls
|
||
Water soluble packets, when used correctly, qualify as a closed mixing/loading system under the worker
|
||
Protection Standard [40 CFR 170.607(d)]. Mixers and loaders handling this product while it is enclosed in
|
||
intact water-soluble packets may elect to wear reduced PPE of long-sleeved shirt, long pants, shoes,
|
||
socks. When reduced PPE is worn because a closed system is being used, handlers must be provided all
|
||
PPE specified above for “applicators and other handlers” and have such PPE immediately available for
|
||
use in an emergency, such as a spill or equipment break-down.
|
||
|
||
User Safety Recommendations
|
||
Users should:
|
||
• Wash hands before eating, drinking, chewing gum, using tobacco or using the toilet.
|
||
• Remove clothing/PPE immediately if pesticides get inside. Then wash and put on clean clothing.
|
||
• Remove PPE immediately after handling product. Wash outside of gloves before removing. As soon
|
||
as possible, wash thoroughly and change into clean clothing.
|
||
|
||
Environmental Hazards
|
||
This product is toxic to fish. Do not apply directly to water, or to areas where surface water is present, or
|
||
to intertidal areas below the mean high-water mark. Drift or runoff from treated areas may be hazardous
|
||
to aquatic organisms in adjacent aquatic sites. Do not contaminate water when disposing of equipment
|
||
washwaters or rinsate.
|
||
|
||
DIRECTIONS FOR USE
|
||
It is a violation of Federal law to use this product in a manner inconsistent with its labeling.
|
||
Read all Directions for Use carefully before applying.
|
||
|
||
Do not apply this product in a way that will contact workers or other persons, either directly or through
|
||
drift. Only protected handlers may be in the area during application. For any requirements specific to
|
||
your state or tribe, consult the agency responsible for pesticide regulation.
|
||
|
||
A3B / Indar 75WSP / MSTR / Amend / 09-03-2026 Page 7
|
||
Agricultural Use Requirements
|
||
Use this product only in accordance with its labeling and with the Worker Protection Standard, 40 CFR
|
||
Part 170. This Standard contains requirements for the protection of agricultural workers on farms, forests,
|
||
nurseries, and greenhouses, and handlers of agricultural pesticides. It contains requirements for training,
|
||
decontamination, notification, and emergency assistance. It also contains specific instructions and
|
||
exceptions pertaining to the statements on this label about personal protective equipment (PPE)and
|
||
restricted-entry interval. The requirements in this box only apply to uses of this product that are covered
|
||
by the Worker Protection Standard.
|
||
|
||
Do not enter or allow worker entry into treated areas during the restricted entry interval (REI) of 12 hours.
|
||
|
||
PPE required for early entry to treated areas that is permitted under the Worker Protection Standard and
|
||
that involves contact with anything that has been treated, such as plants, soil or water, is:
|
||
• Coveralls over long-sleeved shirt and pants
|
||
• Shoes plus socks
|
||
• Waterproof gloves
|
||
|
||
Product Information
|
||
|
||
Indar® 75WSP fungicide is a systemic fungicide with preventative and curative properties used for the
|
||
control of specific diseases listed on this label. For optimal disease control with Indar 75WSP, apply
|
||
sprays on a preventive spray program.
|
||
|
||
Indar 75WSP is considered not hazardous to bees, including those which are actively foraging in the area
|
||
during application, when used as directed.
|
||
|
||
A non-polymer containing spray adjuvant approved for use with registered pesticide products may be
|
||
added to spray solutions according to manufacturer’s use instructions to achieve optimum disease
|
||
control.
|
||
|
||
Do not apply Indar 75WSP in greenhouses.
|
||
|
||
Resistance Management
|
||
|
||
For resistance management, Indar 75WSP contains a Group G1 fungicide. Any fungal population may
|
||
contain individuals naturally resistant to Indar 75WSP and other Group G1 fungicides. A gradual or total
|
||
loss of pest control may occur over time if these fungicides are used repeatedly in the same fields.
|
||
Appropriate resistance-management strategies should be followed.
|
||
|
||
To delay fungicide resistance, take one or more of the following steps:
|
||
• Avoid application of more than the maximum consecutive sprays of Indar 75WSP or other
|
||
fungicides in the same group in a season (see specific max application guidelines in Directions
|
||
for Use).
|
||
• Use tank mixtures with fungicide from a different group that are equally effective on the target
|
||
pest when such use is permitted. Use at least the minimum application rate as labeled by the
|
||
manufacturer.
|
||
• Adopt an integrated disease management program for fungicide use that includes scouting, uses
|
||
historical information related to pesticide use, and crop rotation, and which considers host plant
|
||
resistance, impact of environmental conditions on disease development, disease thresholds, as
|
||
well as cultural, biological and other chemical control practices.
|
||
• Where possible, make use of predictive disease models to effectively time fungicide applications.
|
||
Note that using predictive models alone is not sufficient to manage resistance.
|
||
• Monitor treated fungal populations for resistance development.
|
||
• Contact your local extension specialist or certified crop advisor for any additional pesticide
|
||
resistance-management and/or IPM recommendations for specific crops and pathogens.
|
||
|
||
A3B / Indar 75WSP / MSTR / Amend / 09-03-2026 Page 8
|
||
• Contact your extension specialist, certified crop consultant, or Corteva Agriscience representative
|
||
for the latest resistance management information.
|
||
|
||
Use Rate Determination
|
||
|
||
Carefully read, understand and follow label use rates and restrictions. Under low disease conditions, use
|
||
minimum application rates, while maximum application rates and shortened spray schedules are for
|
||
severe or threatening disease conditions. For proper application, determine the number of acres to be
|
||
treated, the label use rate and the gallonage to be applied per acre. Prepare only the amount of spray
|
||
solution required to treat the measured acreage. Carefully calibrate spray equipment prior to use.
|
||
|
||
Handling for Water Soluble Pouches
|
||
|
||
Soluble Packages (WSPs) are designed to dissolve in water. Agitation may be used, if necessary, to help
|
||
dissolve the WSP. Failure to follow handling and mixing instructions can increase your exposure to the
|
||
pesticide products in WSPs. WSPs, when used properly, qualify as a closed mixing/loading system under
|
||
the Agricultural Worker Protection Standard [40 C.F.R. 170.607(d)].
|
||
|
||
Handling Instructions
|
||
Follow these steps when handling pesticide products in WSPs.
|
||
|
||
1. Mix in spray tank only.
|
||
2. Handle the WSP in a manner that protects package from breakage and/or unintended release of
|
||
contents. If package is broken, put on PPE required for clean-up and then continue with mixing
|
||
instructions.
|
||
3. Keep the WSP in outer packaging until just before use.
|
||
4. Keep the WSP dry prior to adding to the spray tank.
|
||
5. Handle with dry gloves and according to the label instructions for PPE.
|
||
6. Keep the WSP intact. Do not cut or puncture the WSP.
|
||
7. Reseal the WSP outer packaging to protect any unused WSP(s).
|
||
|
||
Mixing Directions
|
||
|
||
Follow the steps below when mixing this product, including if it is tank-mixed with other pesticide
|
||
products. If being tank-mixed, the mixing directions 1 through 9 below take precedence over the
|
||
mixing directions of the other tank mix products. WSPs may, in some cases, be mixed with other
|
||
pesticide products so long as the directions for use of all the pesticide product components do not
|
||
conflict. Do not tank-mix this product with products that prohibit tank-mixing or have conflicting mixing
|
||
directions. Note: Reduced product efficacy may occur if water containing suspended soil particles,
|
||
such as water from ponds, streams or unlined ditches, is used.
|
||
|
||
1. If a basket or strainer is present in the tank hatch, remove prior to adding the WSP to tank.
|
||
2. Fill tank with water to approximately one-third to one-half of the desired final volume of spray.
|
||
3. Stop adding water and stop any agitation.
|
||
4. Place intact/unopened WSP into the tank.
|
||
5. Do not spray water from a hose or fill pipe to break or dissolve the WSP.
|
||
6. Start mechanical and recirculation agitation from the bottom of tank without using any
|
||
overhead recirculation, if possible. If overhead recirculation cannot be turned off, close the
|
||
hatch before starting agitation.
|
||
7. Dissolving the WSP may take up to 5 minutes or longer, depending on water temperature,
|
||
water hardness and intensity of agitation.
|
||
8. Stop agitation before tank lid is opened.
|
||
9. Open the lid to the tank, exercising caution to avoid contact with dusts or spray mix, to verify
|
||
that the WSP has fully dissolved and the contents have been thoroughly mixed into the
|
||
solution.
|
||
10. Do not add other allowed products or complete filling the tank until the bags have fully
|
||
dissolved and pesticide is thoroughly mixed.
|
||
|
||
A3B / Indar 75WSP / MSTR / Amend / 09-03-2026 Page 9
|
||
11. Once the WSP has fully dissolved and any other products have been added to the tank,
|
||
resume filling the tank with water to the desired level, close the tank lid, and resume agitation.
|
||
12. Use the spray solution when mixing is complete.
|
||
13. Maintain agitation of the diluted pesticide mix during transport and application.
|
||
14. It is unlawful to use any registered pesticide, including WSPs, in a manner inconsistent with
|
||
its label.
|
||
|
||
Application Directions
|
||
|
||
Do not make ground or aerial applications within 75 feet of streams, rivers, ponds, lakes or reservoirs.
|
||
|
||
Spray Drift Advisories
|
||
|
||
THE APPLICATOR IS RESPONSIBLE FOR AVOIDING OFF-SITE SPRAY DRIFT.
|
||
BE AWARE OF NEARBY NON-TARGET SITES AND ENVIRONMENTAL CONDITIONS.
|
||
|
||
Importance Of Droplet Size
|
||
An effective way to reduce spray drift is to apply large droplets. Use the largest droplets that provide
|
||
target pest control. While applying larger droplets will reduce spray drift, the potential for drift will be
|
||
greater if applications are made improperly or under unfavorable environmental conditions.
|
||
|
||
Controlling Droplet Size – Ground Boom
|
||
• Volume - Increasing the spray volume so that larger droplets are produced will reduce spray drift.
|
||
Use the highest practical spray volume for the application. If a greater spray volume is needed,
|
||
consider using a nozzle with a higher flow rate.
|
||
• Pressure - Use the lowest spray pressure recommended for the nozzle to produce the target
|
||
spray volume and droplet size.
|
||
• Spray Nozzle - Use a spray nozzle that is designed for the intended application. Consider using
|
||
nozzles designed to reduce drift.
|
||
|
||
Controlling Droplet Size – Aircraft
|
||
• Adjust Nozzles - Follow nozzle manufacturers’ recommendations for setting up nozzles.
|
||
Generally, to reduce fine droplets, nozzles should be oriented parallel with the airflow in flight.
|
||
• The distance of the outer most nozzles on the boom must not exceed 3/4 the length of the
|
||
wingspan or rotor.
|
||
• Nozzles must always point backward parallel with the air stream and never be pointed
|
||
downwards more than 45 degrees.
|
||
• Where states have more stringent regulations, they must be observed.
|
||
|
||
Boom Height – Ground Boom
|
||
For ground equipment, the boom should remain level with the crop and have minimal bounce.
|
||
|
||
Release Height – Aircraft
|
||
Higher release heights increase the potential for spray drift.
|
||
|
||
Shielded Sprayers
|
||
Shielding the boom or individual nozzles can reduce spray drift. Consider using shielded sprayers. Verify
|
||
that the shields are not interfering with the uniform deposition of the spray on the target area.
|
||
|
||
Temperature and Humidity
|
||
When making applications in hot and dry conditions, use larger droplets to reduce effects of evaporation.
|
||
|
||
Temperature Inversions
|
||
Drift potential is high during a temperature inversion. Temperature inversions are characterized by
|
||
increasing temperature with altitude and are common on nights with limited cloud cover and light to no
|
||
wind. The presence of an inversion can be indicated by ground fog or by the movement of smoke from a
|
||
|
||
A3B / Indar 75WSP / MSTR / Amend / 09-03-2026 Page 10
|
||
ground source or an aircraft smoke generator. Smoke that layers and moves laterally in a concentrated
|
||
cloud (under low wind conditions) indicates an inversion, while smoke that moves upward and rapidly
|
||
dissipates indicates good vertical air mixing. Avoid applications during temperature inversions.
|
||
|
||
Wind
|
||
Drift potential generally increases with wind speed. AVOID APPLICATIONS DURING GUSTY WIND
|
||
CONDITIONS.
|
||
Applicators need to be familiar with local wind patterns and terrain that could affect spray drift.
|
||
|
||
Boomless Ground Applications:
|
||
Setting nozzles at the lowest effective height will help to reduce the potential for spray drift.
|
||
|
||
Handheld Technology Applications:
|
||
Take precautions to minimize spray drift.
|
||
|
||
Ground Application
|
||
Thorough coverage sprays generally result in optimum disease control. To achieve good coverage, use
|
||
proper spray pressure, gallonage per acre, nozzles, nozzle spacing and tractor speed. Consult spray
|
||
nozzle and accessory catalogues for specific information on proper equipment calibration. For tree fruits
|
||
and nuts, apply the same amount of Indar 75WSP per acre in either dilute or concentrate sprays.
|
||
|
||
Aerial Application
|
||
Apply in a minimum of 5 gallons of water per acre on annual crops and 10 gallons of water per acre on
|
||
perennial tree fruits and nuts. Do not apply Indar 75WSP under conditions when uniform coverage
|
||
cannot be obtained or when excessive spray drift may occur. Flagmen and loaders should wash
|
||
thoroughly before eating, drinking or smoking and at the end of each day’s spray operation.
|
||
|
||
Chemigation Application
|
||
Apply Indar 75WSP through properly equipped chemigation systems for disease control in cranberry on a
|
||
regular protectant fungicide schedule. Follow use directions for cranberry in the Uses section of this
|
||
label. Do not apply Indar 75WSP by chemigation to other labeled crops.
|
||
|
||
General Directions for Sprinkler Chemigation: Apply Indar 75WSP only through overhead sprinkler
|
||
irrigation systems that will apply water uniformly, including center pivot, lateral move, end tow, side
|
||
(wheel) roll, traveler, big gun, solid set, or hand move. Do not apply this product through any other type
|
||
of irrigation system. Sprinkler systems that deliver a low coefficient of uniformity such as certain water
|
||
drive units are not recommended.
|
||
|
||
Chemigation Preparation: The following use directions are to be followed when this product is applied
|
||
through sprinkler irrigation systems. Thoroughly clean the chemigation system and tank of any fertilizer
|
||
or chemical residues, and dispose of the residues according to state and federal laws. Flush the injection
|
||
system with soap or a cleaning agent and water. Determine the amount of Indar 75WSP needed to cover
|
||
the desired acreage. Mix according to instructions in the Mixing Directions section. Continually agitate
|
||
the mixture during mixing and application.
|
||
|
||
Chemigation Equipment Calibration: It is suggested that the injection pump/system be calibrated at
|
||
least twice before operation, and the system must be monitored during operation.
|
||
|
||
Center Pivot, Lateral Move, End Tow, Traveler Irrigation Equipment: Use this equipment only with
|
||
electric or oil hydraulic drive systems, which provide a uniform water distribution. In order to calibrate the
|
||
irrigation system and injector to apply the mixture containing Indar 75WSP, determine the following: 1)
|
||
Calculate the number of acres irrigated by the system; 2) Calculate the time required to apply no more
|
||
than 1/4 water (6.750 gallons of water per acre) over the area to be treated when the system and injection
|
||
equipment are operated at normal pressures specified by the equipment manufacturer (run system at 80
|
||
to 95% of manufacturer’s rated capacity); 3) Calculate the injection pump output when operated at normal
|
||
line pressure using only water; 4) Calculate the total amount of fungicide mixture needed to cover the
|
||
|
||
A3B / Indar 75WSP / MSTR / Amend / 09-03-2026 Page 11
|
||
desired acreage; 5) Add the required amount of Indar 75WSP and water to meet the injection time
|
||
requirements of the solution tank.
|
||
|
||
Solid Set, Side (Wheel) Roll, Hand Move Irrigation Equipment: In order to calibrate the irrigation
|
||
system and injector to apply the mixture containing Indar 75WSP, determine the following: 1) Calculate
|
||
the number of acres irrigated by the system; 2) Fill the injector solution tank with water and adjust the flow
|
||
rate to use the contents over a 10- to 30-minute interval; 3) Calculate the total amount of fungicide
|
||
mixture needed to cover the desired acreage and add Indar 75WSP into the same quantity of water used
|
||
to calibrate the injection equipment. Operate the system at normal pressures specified by the
|
||
manufacturer and used for the time interval established during calibration.
|
||
|
||
Chemigation Operation: Start the water pump and irrigation system, and let the system achieve the
|
||
desired pressure and speed before starting the injector. Check for leaks and uniformity and make repairs
|
||
before any chemigation takes place. Start the injection system and calibrate according to manufacturer’s
|
||
specifications. This procedure is necessary to deliver the desired rate per acre in a uniform manner.
|
||
Inject Indar 75WSP at the end of the irrigation cycle or as a separate application to maximize foliar
|
||
fungicide retention. When the application is finished, allow the entire irrigation and injection system to be
|
||
thoroughly flushed clean before stopping the system.
|
||
|
||
Chemigation Precautions:
|
||
• Lack of effectiveness or illegal pesticide residues in the crop can result from non-uniform distribution of
|
||
treated water.
|
||
• If you have questions about calibration, contact state extension service specialists, equipment
|
||
manufacturers or other experts.
|
||
• Do not connect an irrigation system used for pesticide application (including greenhouse systems) to a
|
||
public water system unless the pesticide label prescribed safety devices for public water systems are in
|
||
place with current certification. Specific local regulations may apply and must be followed.
|
||
• A person knowledgeable of the chemigation system and responsible for its operation, or under the
|
||
supervision of the responsible person, shall operate the system and make necessary adjustments
|
||
should the need arise and continuously monitor the injection.
|
||
• Do not apply when wind speed favors drift beyond the area intended for treatment. End guns must be
|
||
turned off during the application if they irrigate non-target areas.
|
||
• Do not allow irrigation water to collect or run off and pose a hazard to livestock, wells, or adjoining
|
||
crops.
|
||
• Do not enter treated area during the reentry interval specified in the Agricultural Use Requirements
|
||
section of this label unless required PPE is worn.
|
||
• Do not apply through sprinkler systems that deliver a low coefficient of uniformity such as certain water
|
||
drive units.
|
||
|
||
Chemigation Specific Equipment Requirements:
|
||
• The system must contain an air gap, or approved back flow prevention device, or approved functional
|
||
check valve, vacuum relief valve (including inspection port), and low-pressure drain appropriately
|
||
located on the irrigation pipeline to prevent water source contamination from back flow. Refer to the
|
||
American Society of Agricultural Engineer's Engineering Practice 409 for more information or state
|
||
specific regulations.
|
||
• The pesticide injection line must contain a functional, automatic, quick-closing check valve to prevent
|
||
the flow of fluid back toward the injection chemical supply.
|
||
• A pesticide injection pump must also contain a functional interlock, e.g., mechanical or electrical, to shut
|
||
off chemical supply when the irrigation system is either automatically or manually shut down.
|
||
• The system must contain functional interlocking controls to automatically shut off the pesticide injection
|
||
when the water pressure drops too low or water flow stops.
|
||
• Use of public water supply requires approval of a backflow prevention device or air gap (preferred) by
|
||
both state and local authorities.
|
||
• Systems must use a metering pump, such as a positive displacement injection pump (or flow meter on
|
||
eductor), effectively designed and constructed of materials that are compatible with pesticides and
|
||
|
||
A3B / Indar 75WSP / MSTR / Amend / 09-03-2026 Page 12
|
||
capable of being fitted with a system interlock. An electric powered pump must meet Section 675 for
|
||
"Electrically Driven or Controlled Irrigation Machines" NEC 70.
|
||
• To ensure uniform mixing of the fungicide into the water line, inject the mixture in the center of the pipe
|
||
diameter or just ahead of an elbow or tee in the irrigation line so that the turbulence created at those
|
||
points will assist in mixing. The injection point must be located after all back flow prevention devices on
|
||
the water line.
|
||
• The tank holding the fungicide mixture should be free of rust, fertilizer, sediment, and foreign material,
|
||
and equipped with an in-line strainer situated between the tank and the injection point.
|
||
|
||
Orchard Use
|
||
|
||
Apply Indar 75WSP to orchards using a dilute or concentrate spray.
|
||
|
||
Dilute Spray: Dilute or thorough coverage applications are based upon the amount of spray solution
|
||
necessary to thoroughly wet the trees until spray run-off. To determine the number of gallons of dilute
|
||
spray required per acre, contact your state agricultural experiment station, certified pest control advisor,
|
||
or extension specialist for assistance.
|
||
|
||
Concentrate Spray: Concentrate spray applications assume all of the tree is uniformly covered with
|
||
spray solution but not to the point of run-off. A lower spray volume is used to deliver the same application
|
||
rate per acre as used for a dilute spray. Use a minimum of 50 gallons of spray solution per acre for
|
||
concentrate sprays with Indar 75WSP.
|
||
|
||
Compatibility
|
||
|
||
Indar 75WSP is compatible with most commonly used agriculture fungicides, insecticides, growth
|
||
regulators, micronutrients and spray adjuvants. When preparing tank mixes, consult spray compatibility
|
||
charts or State Cooperative Extension Service Specialists prior to actual use. Indar 75WSP is compatible
|
||
with boron and spray oils; however, the water-soluble pouches must be completely dissolved before
|
||
adding spray oils or products containing boron to spray mixtures.
|
||
|
||
Use of Adjuvants
|
||
Surfactants may improve spray coverage, especially for waxy leaf surfaces. For best results do not use
|
||
penetrants. Use only adjuvants that are registered for agricultural use and are known to be safe for the
|
||
crop. Follow directions on the manufacturer’s label. When an adjuvant is to be used with this product,
|
||
Corteva Agriscience recommends the use of a Chemical Producers and Distributors Association certified
|
||
adjuvant. For nonionic surfactants, a spray mix concentration of 0.25% v/v or less generally is sufficient.
|
||
For organosilicones, a spray mix concentration of 0.05% v/v or less generally is sufficient. Conduct a
|
||
compatibility test (jar test) using the relative proportions of the tank mix ingredients before mixing
|
||
ingredients in the spray tank.
|
||
|
||
Plantback Intervals
|
||
|
||
Plantback intervals (PBI) for crops without primary label uses (such as rotational crops), where the last
|
||
application of the product expended is <0.188 lb active per acre, the PBI must be 35 days. Where the
|
||
last application of the product expended is 0.188 to 1 lb active per acre, the PBI must be 210 days.
|
||
|
||
A3B / Indar 75WSP / MSTR / Amend / 09-03-2026 Page 13
|
||
Uses
|
||
|
||
Almond
|
||
|
||
|
||
Disease
|
||
Indar 75WSP
|
||
Use Directions
|
||
|
||
Restrictions oz/100 gal1 oz/acre
|
||
blossom blight
|
||
(Monilinia spp.)
|
||
0.4 – 0.67 1.25 - 2
|
||
(0.06 - 0.094 lb
|
||
active)
|
||
Begin applications at pink
|
||
bud stage (about 5%
|
||
bloom).
|
||
If conditions are favorable
|
||
for disease development,
|
||
apply again at full bloom
|
||
and at petal fall.
|
||
Apply aerially in a minimum
|
||
of 10 gallons of water per
|
||
acre or by ground in a
|
||
minimum of 20 gallons of
|
||
water per acre.
|
||
• Do not make more
|
||
than 3 applications or
|
||
apply more than a
|
||
total of 6 oz of Indar
|
||
75WSP (0.28 lb
|
||
active) per acre per
|
||
year.
|
||
• Preharvest Interval:
|
||
Do not apply within
|
||
160 days of harvest.
|
||
• Minimum Re-
|
||
Treatment Interval:
|
||
10 days
|
||
• Do not apply this
|
||
product by
|
||
chemigation to
|
||
almond.
|
||
1 Based upon a standard of 300 gallons of dilute spray per acre or the equivalent amount of product per
|
||
acre as a concentrate spray.
|
||
|
||
Apple
|
||
|
||
|
||
Disease
|
||
Indar 75WSP
|
||
oz/acre1
|
||
|
||
Use Directions
|
||
|
||
Restrictions
|
||
flyspeck (Zygophiala
|
||
jamaicensis)
|
||
powdery mildew
|
||
(Podosphaera
|
||
leucotricha)
|
||
rusts
|
||
(Gymnosporangium
|
||
spp.)
|
||
scab (Venturia
|
||
ineaqualis)
|
||
sooty blotch
|
||
(Gloeodes
|
||
pomigena)
|
||
2 - 2.67
|
||
(0.094 - 0.125 lb
|
||
active)
|
||
Begin application at green tip
|
||
or when environmental
|
||
conditions become favorable
|
||
for disease development.
|
||
Apply on a 7- to 10-day
|
||
schedule through the first
|
||
cover spray; thereafter, apply
|
||
on a 10- to 14-day schedule.
|
||
Apply aerially in a minimum of
|
||
10 gallons of water per acre
|
||
or by ground in a minimum of
|
||
20 gallons of water per acre.
|
||
• Do not make more than 4
|
||
applications or apply more
|
||
than a total of 10.67 oz of
|
||
Indar 75WSP (0.5 lb active)
|
||
per acre per year.
|
||
• Preharvest Interval: Do not
|
||
apply within 14 days of
|
||
harvest.
|
||
• Do not graze livestock in
|
||
treated areas or feed cover
|
||
crops grown in treated areas
|
||
to livestock.
|
||
• Do not apply this product by
|
||
chemi
|
||
gation to apple.
|
||
1Maintain per acre use rate regardless of spray volume per acre.
|
||
|
||
A3B / Indar 75WSP / MSTR / Amend / 09-03-2026 Page 14
|
||
Blueberry
|
||
|
||
|
||
Disease
|
||
Indar 75WSP
|
||
oz/acre
|
||
|
||
Use Directions
|
||
|
||
Restrictions
|
||
alternaria (Alternaria
|
||
spp.)
|
||
anthracnose
|
||
(Colletotrichum
|
||
gloeosporioides)
|
||
leaf spot and blotch
|
||
(Mycosphaerella spp.,
|
||
Septoria spp.)
|
||
mummy berry disease
|
||
(Monilinia vaccinii-
|
||
corymbosi)
|
||
phomopsis twig blight
|
||
and fruit rot
|
||
(Phomopsis vaccinii)
|
||
powdery mildew
|
||
(Microsphaera
|
||
vaccinii)
|
||
rusts (Puccianiastrum
|
||
spp.
|
||
)
|
||
2 – 2.67
|
||
(0.094 – 0.125
|
||
lb active)
|
||
For mummy berry and
|
||
phomopsis twig blight, begin
|
||
applications when the plants
|
||
break dormancy (at early
|
||
green tip or bloom,
|
||
depending upon variety), and
|
||
make subsequent
|
||
applications at intervals of 8
|
||
to 14 days.
|
||
For control of powdery
|
||
mildew and other listed
|
||
diseases, begin applications
|
||
prior to or at onset of disease
|
||
development and repeat at
|
||
8- to 14-day intervals.
|
||
Apply aerially in a minimum of
|
||
10 gallons of water per acre
|
||
or by ground in a minimum of
|
||
20
|
||
gallons of water per acre.
|
||
• Do not make more than 4
|
||
applications or apply more
|
||
than a total of 8 oz of Indar
|
||
75WSP (0.38 lb active) per
|
||
acre per year.
|
||
• Preharvest Interval: Do
|
||
not apply within 30 days of
|
||
harvest.
|
||
• Do not graze livestock in
|
||
treated fields or offer
|
||
treated material as a
|
||
livestock feed item.
|
||
• Do not apply this product
|
||
by chemigation to
|
||
blueberry.
|
||
|
||
Citrus Fruits (Crop Group 10)1
|
||
1Citrus fruits (crop group 10) including: calamondin, citrus citron, chironja, citrus hybrids, grapefruit,
|
||
kumquat, lemon, lime, orange (sour, sweet, mandarin), pummelo, satsuma mandarin, tangerine, tangelo,
|
||
tangor
|
||
|
||
Apply aerially in a minimum of 10 gallons of water per acre or by ground in a minimum of 20 gallons of
|
||
water per acre. Obtain optimum disease control by applying Indar 75WSP with a nonionic surfactant or
|
||
spray oil at the manufacturer’s specified rate and making thorough coverage applications.
|
||
|
||
|
||
Disease
|
||
Indar 75WSP
|
||
oz/acre
|
||
|
||
Use Directions
|
||
|
||
Restrictions
|
||
greasy spot
|
||
(Mycosphaerella
|
||
citri)
|
||
2.67
|
||
(0.125 lb
|
||
active)
|
||
Make the first application at the
|
||
normal timing for greasy spot
|
||
in your area. Make a second
|
||
application for control of
|
||
greasy spot of foliage and rind
|
||
blotch of fruit after the first
|
||
summer flush. Application for
|
||
control of greasy spot may also
|
||
occur at other times.
|
||
• Do not make more than 3
|
||
applications or apply more
|
||
than a total of 8.01 oz of
|
||
Indar 75WSP (0.375 lb
|
||
active) per acre per year.
|
||
• Preharvest Interval: Up to
|
||
day of harvest.
|
||
• Minimum Re-Treatment
|
||
Interval: 21 days.
|
||
• Do not allow livestock to
|
||
graze in treated areas.
|
||
• Do not apply Indar 75WSP
|
||
with polymer based spray
|
||
adjuvants.
|
||
• Do not apply this product
|
||
by chemigation to citrus.
|
||
scab (Elsinoe
|
||
fawcettii)
|
||
Make the first application
|
||
between feather flush and 25%
|
||
expansion of spring leaf flush.
|
||
Make a second application at
|
||
petal fall. Follow 3 to 4 weeks
|
||
later with another fungicide for
|
||
control of late scab and early
|
||
melanose.
|
||
sooty mold
|
||
(Capnodium spp.)
|
||
Applications made for control of
|
||
greasy spot or scab will also
|
||
control soot
|
||
y mold.
|
||
|
||
A3B / Indar 75WSP / MSTR / Amend / 09-03-2026 Page 15
|
||
Cranberry
|
||
|
||
Apply aerially in a minimum of 5 gallons of water per acre or by ground in a minimum of 20 gallons of
|
||
water per acre. This product may also be used in a chemigation application to cranberry (see
|
||
Chemigation Application section). For optimum disease control, use an agriculturally registered non-
|
||
polymer nonionic surfactant at the manufacturer’s specified rate.
|
||
|
||
|
||
Disease
|
||
Indar 75WSP
|
||
oz/acre
|
||
|
||
Use Directions
|
||
|
||
Restrictions
|
||
cottonball tip blight
|
||
(Monilinia oxycocci)
|
||
2 - 4
|
||
(0.094 - 0.188
|
||
lb active)
|
||
Begin applications when
|
||
50% of the shoots have
|
||
begun to elongate. Refer to
|
||
your local spray guides for
|
||
more specific application
|
||
timin
|
||
g information.
|
||
• Do not make more than 4
|
||
applications or apply more
|
||
than a total of 16 oz of Indar
|
||
75WSP (0.75 lb active) per
|
||
acre per year.
|
||
• Preharvest Interval: Do not
|
||
apply within 30 days of
|
||
harvest.
|
||
cranberry fruit rot
|
||
complex1
|
||
Begin applications prior to
|
||
bloom at the onset of
|
||
disease. Continue on a 10-
|
||
to 14-day spray schedule
|
||
depending upon local
|
||
conditions. Refer to your
|
||
local guides for more
|
||
specific application
|
||
information.
|
||
fairyring complex
|
||
(suppression)
|
||
4
|
||
(0.188 lb
|
||
active)
|
||
For maximum suppression
|
||
of fairyring complex,
|
||
measure 10 ft out from the
|
||
visible fairyring region and
|
||
apply the spray solution of
|
||
Indar 75WSP to this entire
|
||
area. Make the first
|
||
application at bud break
|
||
and repeat once, if
|
||
necessary, 14 days later.
|
||
Apply Indar 75WSP in 30 to
|
||
100 gallons of water per
|
||
acre.
|
||
To improve the performance
|
||
of Indar 75WSP against the
|
||
fairyring complex, irrigate
|
||
the treated area for 1 to 2
|
||
hours following each
|
||
application.
|
||
1Cranberry fruit rot disease complex may contain one or more of the following fungal pathogens:
|
||
Allantophomopsis lycopodina, Botryosphaeria vaccinii, Coleophoma empetri, Diaporthe vaccinii,
|
||
Glomerella cingulata-vaccinii, Godronia cassandrae, Phyllosticta vaccinii, Physalospora vaccinii,
|
||
Colletotrichum spp. , Phomopsis vaccinii and Strasseria geniculata.
|
||
|
||
A3B / Indar 75WSP / MSTR / Amend / 09-03-2026 Page 16
|
||
Peanut
|
||
|
||
|
||
Disease
|
||
Indar 75WSP
|
||
oz/acre
|
||
|
||
Use Directions
|
||
|
||
Restrictions
|
||
early leaf spot
|
||
(Cercospora
|
||
arachidicola)
|
||
1.25 - 2
|
||
(0.062 - 0.094
|
||
lb active)
|
||
Begin foliar applications
|
||
approximately 4 weeks after
|
||
planting or at first sign of
|
||
disease development and
|
||
continue application on a 10-
|
||
to 14-day schedule.
|
||
Apply aerially in a minimum of
|
||
5 gallons of water per acre or
|
||
by ground in a minimum of
|
||
20 gallons of water per acre.
|
||
• Do not make more than 4
|
||
applications or apply more
|
||
than a total of 10.67 oz of
|
||
Indar 75WSP (0.5 lb active)
|
||
per acre per year.
|
||
• Preharvest Interval: Do not
|
||
apply within 14 days of
|
||
harvest.
|
||
• Do not feed hay or threshings
|
||
or allow livestock to graze in
|
||
treated areas.
|
||
• Do not apply this product by
|
||
chemi
|
||
gation to peanut.
|
||
late leaf spot
|
||
(Cercosporidium
|
||
personatum)
|
||
2 – 2.67
|
||
(0.094 - 0.125
|
||
lb active)
|
||
|
||
Pecan
|
||
|
||
|
||
Disease
|
||
Indar 75WSP
|
||
oz/acre
|
||
|
||
Use Directions
|
||
|
||
Restrictions
|
||
downy spot
|
||
(Mycosphaerella
|
||
caryigena)
|
||
gnomonia leafspot
|
||
(Gnomonia dispora)
|
||
leaf blotch
|
||
(Mycosphaerella
|
||
dendroides)
|
||
leaf scorch
|
||
powdery mildew
|
||
(Micosphaera
|
||
penicillata)
|
||
scab (Cladosporium
|
||
caryigenum)
|
||
vein spot (Gnomonia
|
||
nerviseda)
|
||
2 - 2.5
|
||
(0.09 - 0.12 lb
|
||
active)
|
||
Begin applications at bud
|
||
break and continue at 10- to
|
||
14-day intervals through
|
||
pollination. Apply at 14- to
|
||
21-day intervals through the
|
||
cover sprays.
|
||
Apply aerially in a minimum of
|
||
10 gallons of water per acre
|
||
or by ground in a minimum of
|
||
20 gallons of water per acre.
|
||
• Do not make more than 6
|
||
applications or apply more than
|
||
a total of 16 oz of Indar 75WSP
|
||
(0.75 lb active) per acre per
|
||
season.
|
||
• Preharvest Interval: Do not
|
||
apply after shuck split or within
|
||
28 days of harvest.
|
||
• Do not graze livestock in
|
||
treated areas or feed cover
|
||
crops grown in treated areas to
|
||
livestock.
|
||
• Do not apply after shuck split.
|
||
• Do not apply this product by
|
||
chemigation to pecan.
|
||
|
||
A3B / Indar 75WSP / MSTR / Amend / 09-03-2026 Page 17
|
||
Peppers
|
||
Including bell pepper, chili pepper, cooking pepper, pimento, sweet pepper
|
||
|
||
|
||
Disease
|
||
Indar 75WSP
|
||
oz/acre
|
||
|
||
Use Directions
|
||
|
||
Restrictions
|
||
cercospora leaf spot
|
||
powdery mildew
|
||
2 - 4
|
||
(0.094 – 0.188
|
||
lb active)
|
||
Begin applications when
|
||
disease is first observed.
|
||
Reapply 10 to 14 days later
|
||
or as necessary for the level
|
||
of disease pressure present.
|
||
Apply uniformly in a spray
|
||
volume that assures
|
||
thorough coverage of the
|
||
crop. A minimum spray
|
||
volume of 30 gallons per
|
||
acre is necessary. Disease
|
||
control may be reduced at
|
||
low spray volumes or if spray
|
||
coverage is inadequate.
|
||
For optimal disease control,
|
||
apply as a ground
|
||
application. Aerial
|
||
application is permitted;
|
||
however, disease control
|
||
may be reduced when
|
||
product is applied by air.
|
||
For optimum performance, add
|
||
a nonionic surfactant to the
|
||
solution.
|
||
• Do not apply more than 4 oz of
|
||
Indar 75WSP per acre per
|
||
application or more than a total
|
||
of 16 oz of Indar 75WSP (0.75
|
||
lb active) per acre per crop.
|
||
• Do not make more than 2
|
||
consecutive applications of
|
||
Indar 75WSP. Alternate within
|
||
14 days with a product which
|
||
is effective on the target
|
||
pathogen and has a different
|
||
mode of action than Indar
|
||
75WSP.
|
||
• Preharvest Interval: Do not
|
||
apply within 7 days of harvest.
|
||
• Minimum Re-Treatment
|
||
Interval: 10 days
|
||
• Do not apply this product by
|
||
chemigation to peppers.
|
||
|
||
A3B / Indar 75WSP / MSTR / Amend / 09-03-2026 Page 18
|
||
Stone Fruits (Crop Group 12)1
|
||
1Stone fruit (crop group 12) including apricot, chickasaw plum, damson plum, fresh prune, Japanese
|
||
plum, nectarine, peach, plum, plumcot, sweet cherry, tart cherry
|
||
|
||
Apply aerially in a minimum of 5 gallons of water per acre or by ground in a minimum of 20 gallons of
|
||
water per acre. For optimum disease control, add a non-polymer spray adjuvant/wetting agent labeled for
|
||
use on food crops to spray solutions at the manufacturers' specified rate.
|
||
|
||
|
||
Crop
|
||
|
||
Disease
|
||
Indar 75WSP
|
||
oz/acre
|
||
|
||
Use Directions
|
||
|
||
Restrictions
|
||
apricot
|
||
nectarine
|
||
peach
|
||
sweet cherry
|
||
tart cherry
|
||
blossom blight
|
||
(Monilinia spp.)
|
||
2
|
||
(0.094 lb
|
||
active)
|
||
Begin applications at
|
||
early red bud stage
|
||
before infection occurs.
|
||
If conditions are
|
||
favorable for disease
|
||
development, apply
|
||
again at full bloom and
|
||
at petal fall.
|
||
• Do not make more than 8
|
||
applications or apply
|
||
more than a total of 16
|
||
oz of Indar 75WSP (0.75
|
||
lb active) per acre per
|
||
season.
|
||
• Preharvest Interval: Up
|
||
to day of harvest.
|
||
• Do not graze livestock in
|
||
treated areas or feed
|
||
cover crops grown in
|
||
treated areas to
|
||
livestock.
|
||
• Do not apply this product
|
||
by chemigation to stone
|
||
fruits.
|
||
fruit brown rot
|
||
(Monilinia spp.)
|
||
Begin applications 2 to 3
|
||
weeks before harvest
|
||
using a 7- to 10-day
|
||
spray interval.
|
||
sweet cherry
|
||
tart cherry
|
||
leaf spot
|
||
(Blumeriella spp.)
|
||
Follow blossom blight
|
||
schedule and continue
|
||
application at 10- to 14-
|
||
day intervals. Additional
|
||
foliar applications may
|
||
be made after harvest.
|
||
peach scab
|
||
(Cladosporium
|
||
spp.)
|
||
Begin applications at
|
||
shuck split. Make 2 to 3
|
||
subsequent thorough
|
||
coverage applications at
|
||
10- to 14-da
|
||
y intervals.
|
||
chickasaw
|
||
plum
|
||
damson plum
|
||
fresh prune
|
||
Japanese
|
||
plum
|
||
plum
|
||
plumcot
|
||
blossom blight
|
||
(Monilinia spp.)
|
||
Begin applications at
|
||
early red bud stage
|
||
before infection occurs.
|
||
If conditions are
|
||
favorable for disease
|
||
development, apply
|
||
again at full bloom and
|
||
at petal fall.
|
||
• Do not make more than 4
|
||
applications or apply
|
||
more than a total of 8 oz
|
||
of Indar 75WSP (0.38 lb
|
||
active) per acre per year.
|
||
• Preharvest Interval: Up
|
||
to day of harvest.
|
||
• Do not graze livestock in
|
||
treated areas or feed
|
||
cover crops grown in
|
||
treated areas to
|
||
livestock.
|
||
• Do not apply this product
|
||
by chemigation to stone
|
||
fruits.
|
||
fruit brown rot
|
||
(Monilinia spp.)
|
||
Begin applications 2 to 3
|
||
weeks before harvest
|
||
using a 7- to 10-day
|
||
spray interval.
|
||
|
||
A3B / Indar 75WSP / MSTR / Amend / 09-03-2026 Page 19
|
||
Sugarbeets
|
||
|
||
|
||
Disease
|
||
Indar 75WSP
|
||
oz/acre
|
||
|
||
Use Directions
|
||
|
||
Restrictions
|
||
cercospora leaf spot
|
||
(Cercospora
|
||
beticola)
|
||
powdery mildew
|
||
(Erysiphe spp.)
|
||
2.67
|
||
(0.125 lb
|
||
active)
|
||
Apply Indar 75WSP at
|
||
intervals of 14 to 21 days
|
||
beginning when conditions
|
||
are favorable for disease
|
||
development.
|
||
For resistance management,
|
||
alternate applications of
|
||
Indar 75WSP with a non-
|
||
triazole fungicide labeled for
|
||
use on sugarbeets.
|
||
For optimum disease control,
|
||
an adjuvant, such as crop oil
|
||
concentrate that is labeled
|
||
for crop use, may be added
|
||
to the spray mixture at the
|
||
manufacturer’s specified
|
||
rate. Add an adjuvant to the
|
||
spray solution last.
|
||
For best spray coverage of
|
||
foliage, apply aerially in a
|
||
minimum of 5 to 7 gallons of
|
||
water per acre or by ground
|
||
in a minimum of 20 gallons
|
||
of water per acre.
|
||
• Do not make more than 2
|
||
applications or apply more
|
||
than a total of 5.34 oz of
|
||
Indar 75WSP (0.25 lb active)
|
||
per acre per year.
|
||
• Preharvest Interval: Do not
|
||
apply within 14 days of
|
||
harvest.
|
||
• Do not apply this product by
|
||
chemigation to sugarbeets.
|
||
|
||
Wheat
|
||
|
||
|
||
Disease
|
||
Indar 75WSP
|
||
oz/acre
|
||
|
||
Use Directions
|
||
|
||
Restrictions
|
||
glume blotch
|
||
(Septoria nodorum)
|
||
leaf blight, spot
|
||
blotch, barley scald
|
||
(Rhynchosprium
|
||
spp.)
|
||
leaf blotch (Septoria
|
||
tritici)
|
||
powdery mildew
|
||
(Erysiphe graminis)
|
||
rusts (Puccinia spp.)
|
||
tan spot, net blotch
|
||
(Pyrenophora spp.)
|
||
1.25
|
||
(0.06 lb active)
|
||
Apply anytime through
|
||
heading (Feekes growth
|
||
stage 10.3 to 10.5) on a 7-
|
||
to 21-day schedule.
|
||
Apply aerially in a minimum
|
||
of 5 gallons of water per
|
||
acre or by ground in a
|
||
minimum of 15 gallons of
|
||
water per acre.
|
||
• Do not make more than 2
|
||
applications or apply more
|
||
than a total of 2.5 oz of Indar
|
||
75WSP (0.12 lb active) per
|
||
acre per year.
|
||
• Preharvest Interval: Do not
|
||
apply after completion of
|
||
flowering (Feekes growth
|
||
stage 10.5) or within 35 days
|
||
of harvest.
|
||
• Preharvest Interval: Do not
|
||
apply within 14 days of
|
||
harvest for forage and hay.
|
||
• Do not apply this product by
|
||
chemi
|
||
gation to wheat.
|
||
|
||
Storage and Disposal
|
||
Do not contaminate water, food or feed by storage or disposal.
|
||
Pesticide Storage: Store in a cool, dry area above freezing. If in a water-soluble pouch, the water-
|
||
soluble pouch may become brittle at storage temperatures below 32°F but the fungicide is not affected.
|
||
Do not remove the water-soluble pouches from container except for immediate use.
|
||
|
||
A3B / Indar 75WSP / MSTR / Amend / 09-03-2026 Page 20
|
||
Pesticide Disposal: Wastes resulting from the use of this product may be disposed of on site or at an
|
||
approved waste disposal facility.
|
||
|
||
Nonrefillable rigid containers 5 gallons or less:
|
||
Container Handling: Nonrefillable container. Do not reuse or refill this container. Offer for recycling if
|
||
available.
|
||
Triple rinse or pressure rinse container (or equivalent) promptly after emptying. Triple rinse as follows:
|
||
Empty the remaining contents into application equipment or a mix tank and drain for 10 seconds after the
|
||
flow begins to drip. Fill the container 1/4 full with water and recap. Shake for 10 seconds. Pour rinsate
|
||
into application equipment or a mix tank or store rinsate for later use or disposal. Drain for 10 seconds
|
||
after the flow begins to drip. Repeat this procedure two more times. Pressure rinse as follows: Empty
|
||
the remaining contents into application equipment or a mix tank and continue to drain for 10 seconds after
|
||
the flow begins to drip. Hold container upside down over application equipment or mix tank or collect
|
||
rinsate for later use or disposal. Insert pressure rinsing nozzle in the side of the container, and rinse at
|
||
about 40 psi for at least 30 seconds. Drain for 10 seconds after the flow begins to drip. Then offer for
|
||
recycling if available. Or puncture and dispose of in a sanitary landfill, or by incineration, or by other
|
||
procedures allowed by state and local authorities.
|
||
|
||
Nonrefillable nonrigid containers:
|
||
Container Handling: Nonrefillable container. Do not reuse or refill this container. Offer for recycling if
|
||
available.
|
||
|
||
Refillable rigid containers larger than 5 gal:
|
||
Container Handling: Refillable container. Refill this container with pesticide only. Do not reuse this
|
||
container for any other purpose.
|
||
Cleaning the container before final disposal is the responsibility of the person disposing of the container.
|
||
Cleaning before refilling is the responsibility of the refiller. To clean the container before final disposal,
|
||
empty the remaining contents from this container into application equipment or a mix tank. Fill the
|
||
container about 10% full with water and, if possible, spray all sides while adding water. If practical,
|
||
agitate vigorously or recirculate water with the pump for two minutes. Pour or pump rinsate into
|
||
application equipment or rinsate collection system. Repeat this rinsing procedure two more times. Then
|
||
offer for recycling if available. Or puncture and dispose of in a sanitary landfill, or by incineration, or if
|
||
allowed by state and local authorities, by burning. If burned, stay out of smoke.
|
||
|
||
Nonrefillable rigid containers larger than 5 gal:
|
||
Container Handling: Nonrefillable container. Do not reuse or refill this container. Offer for recycling if
|
||
available.
|
||
Triple rinse or pressure rinse container (or equivalent) promptly after emptying. Triple rinse as follows:
|
||
Empty the remaining contents into application equipment or a mix tank. Fill the container 1/4 full with
|
||
water. Replace and tighten closures. Tip container on its side and roll it back and forth, ensuring at least
|
||
one complete revolution, for 30 seconds. Stand the container on its end and tip it back and forth several
|
||
times. Turn the container over onto its other end and tip it back and forth several times. Empty the
|
||
rinsate into application equipment or a mix tank or store rinsate for later use or disposal. Repeat this
|
||
procedure two more times. Pressure rinse as follows: Empty the remaining contents into application
|
||
equipment or a mix tank and continue to drain for 10 seconds after the flow begins to drip. Hold container
|
||
upside down over application equipment or mix tank or collect rinsate for later use or disposal. Insert
|
||
pressure rinsing nozzle in the side of the container, and rinse at about 40 psi for at least 30 seconds.
|
||
Drain for 10 seconds after the flow begins to drip. Then offer for recycling if available. Or puncture and
|
||
dispose of in a sanitary landfill, or by incineration, or if allowed by state and local authorities, by burning.
|
||
If burned, stay out of smoke.
|
||
|
||
Terms and Conditions of Use
|
||
If terms of the following Warranty Disclaimer, Inherent Risks of Use and Limitation of Remedies are not
|
||
acceptable, return unopened package at once to the seller for a full refund of purchase price paid. To the
|
||
|
||
A3B / Indar 75WSP / MSTR / Amend / 09-03-2026 Page 21
|
||
extent permitted by law, use by the buyer or any other user constitutes acceptance of the terms under
|
||
Warranty Disclaimer, Inherent Risks of Use and Limitation, of Remedies.
|
||
|
||
Warranty Disclaimer
|
||
Corteva Agriscience warrants that this product conforms to the chemical description on the label and is
|
||
reasonably fit for the purposes stated on the label when used in strict accordance with the directions,
|
||
subject to the inherent risks set forth below. To the extent permitted by law, Corteva Agriscience MAKES
|
||
NO OTHER EXPRESS OR IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A
|
||
PARTICULAR PURPOSE OR ANY OTHER EXPRESS OR IMPLIED WARRANTY.
|
||
|
||
Inherent Risks of Use
|
||
It is impossible to eliminate all risks associated with use of this product. Crop injury, lack of performance,
|
||
or other unintended consequences may result because of such factors as use of the product contrary to
|
||
label instructions (including conditions noted on the label, such as unfavorable temperatures, soil
|
||
conditions, etc.), abnormal conditions (such as excessive rainfall, drought, tornadoes, hurricanes),
|
||
presence of other materials, the manner of application, or other factors, all of which are beyond the
|
||
control of Corteva Agriscience or the seller. Corteva Agriscience will not be responsible for losses or
|
||
damages resulting from the use of this product in any manner not specifically directed by Corteva
|
||
Agriscience. To the extent permitted by law, all such risks associated with non-directed use shall be
|
||
assumed by buyer and/or user.
|
||
|
||
Limitation of Remedies
|
||
To the extent permitted by law, the exclusive remedy for losses or damages resulting from this product
|
||
(including claims based on contract, negligence, tort, strict liability, or other legal theories), shall be limited
|
||
to, at Corteva Agriscience's election, one of the following:
|
||
|
||
1. Refund of purchase price paid by buyer or user for product bought, or
|
||
2. Replacement of amount of product used.
|
||
|
||
To the extent permitted by law, Corteva Agriscience shall not be liable for losses or damages resulting
|
||
from handling or use of this product unless Corteva Agriscience is promptly notified of such loss or
|
||
damage in writing. To the extent permitted by law, in no case shall Corteva Agriscience be liable for
|
||
consequential, incidental or special damages or losses.
|
||
|
||
The terms of the Warranty Disclaimer, Inherent Risks of Use, and this Limitation of Remedies cannot be
|
||
varied by any written or verbal statements or agreements. No employee or sales agent of Corteva
|
||
Agriscience or the seller is authorized to vary or exceed the terms of the Warranty Disclaimer or this
|
||
Limitation of Remedies in any manner.
|
||
|
||
™®Trademarks of Corteva Agriscience and its affiliated companies
|
||
|
||
EPA accepted: __/__/___
|